SpeedTouch™546
Residential ADSL Gateway
User’s Guide
Release R5.3.1
Download from Www.Somanuals.com. All Manuals Search And Download.
SpeedTouch™
546
User’s Guide
R5.3.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright
Copyright ©1999-2005 THOMSON. All rights reserved.
Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization
from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice,
and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or
inaccuracies that may appear in this document.
Thomson Telecom Belgium
Prins Boudewijnlaan, 47
B-2650 Edegem
Belgium
Trademarks
The following trademarks are used in this document:
ꢀ
ꢀ
SpeedTouch™ is a trademark of THOMSON.
Microsoft®, MS-DOS®, Windows® and Windows NT® are either registered trademarks or trademarks of Microsoft Corpora-
tion in the United States and/or other countries.
ꢀ
ꢀ
UNIX® is a registered trademark of UNIX System Laboratories, Incorporated.
Apple® and Mac OS® are registered trademarks of Apple Computer, Incorporated, registered in the United States and other
countries.
ꢀ
Adobe, the Adobe logo, Acrobat and Acrobat Reader are trademarks or registered trademarks of Adobe Systems, Incorpo-
rated, registered in the United States and/or other countries.
ꢀ
ꢀ
ꢀ
ꢀ
Netscape® and Netscape Navigator® are registered trademarks of Netscape Communications Corporation.
Ethernet™ is a trademark of Xerox Corporation.
UPnP™ is a certification mark of the UPnP™ Implementers Corporation.
Wi-Fi® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance. "Wi-Fi CERTIFIED", "Wi-Fi ZONE", "Wi-Fi Alli-
ance", their respective logos and "Wi-Fi Protected Access" are trademarks of the Wi-Fi Alliance.
Other products may be trademarks or registered trademarks of their respective manufacturers.
Document Information
Status: v1.0 (May 2005)
Reference: E-DOC-CTC-20050429-0100
Short Title: User’s Guide ST546 R5.3.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Contents
Hardware Specifications.................................................................................. 5
Software Features.......................................................................................... 6
Remote Assistance....................................................................................... 16
E-DOC-CTC-20050429-0100 v1.0
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
4.1 Navigation.................................................................................... 32
Menu.......................................................................................................... 33
Language Bar............................................................................................... 34
4.2 Home............................................................................................ 38
Information.................................................................................................. 40
SpeedTouch™ Easy Setup.............................................................................. 41
Restart........................................................................................................ 42
Configuration............................................................................................... 43
Update........................................................................................................ 47
4.5 Toolbox ........................................................................................ 53
Remote Assistance....................................................................................... 54
Game or Application Definition....................................................................... 57
New Game or Application.............................................................................. 58
New Content Level....................................................................................... 64
Firewall....................................................................................................... 66
Change Default User..................................................................................... 71
E-DOC-CTC-20050429-0100 v1.0
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Devices....................................................................................................... 74
Device Settings............................................................................................ 75
Interfaces.................................................................................................... 77
Interface Settings......................................................................................... 78
E-DOC-CTC-20050429-0100 v1.0
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
E-DOC-CTC-20050429-0100 v1.0
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
About this User’s Guide
About this User’s Guide
Used Symbols
A note provides additional information about a topic.
A tip provides an alternative method or shortcut to perform an action.
A caution warns you about potential problems or specific precautions that
need to be taken.
!
Terminology Generally, the SpeedTouch™546(i) will be referred to as SpeedTouch™ in this User’s
Guide.
Typographical In interactive input and output, typed input is displayed in a bold fontand
commands are displayed like this.
Comments are added in italics.
Example:
Conventions
=>language list
CODE LANGUAGE VERSION FILENAME
en* english 4.2.0.1 <system>
Only one language is available
Documentation and THOMSON continuously develops new solutions, but is also committed to improve
its existing products.
software updates
For more information on THOMSON's latest technological innovations, documents
and software releases, visit us at:
E-DOC-CTC-20050429-0100 v1.0
1
Download from Www.Somanuals.com. All Manuals Search And Download.
About this User’s Guide
E-DOC-CTC-20050429-0100 v1.0
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
1 Your SpeedTouch™
Introduction With the SpeedTouch™546(i) Residential ADSL Gateway you can build a secure
home or small office network, connecting wired Ethernet devices and surf the
Internet at high speed.
Installation For more information on how to set up your SpeedTouch™, installation and wiring
and how to do a first Internet connection setup, refer to the provided Installation and
Setup Guide.
Contents
This User’s Guide will assist you in configuring your SpeedTouch™.
Safety instructions Before connecting the SpeedTouch™, please read the SpeedTouch™ Quick Installation
Guide and the Safety Instructions and Regularity Notices.
E-DOC-CTC-20050429-0100 v1.0
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
1.1.1 Hardware Specifications
Gateway Integrated multi-mode ADSL modem, supporting:
ꢀ
ꢀ
ꢀ
ADSL over POTS for a SpeedTouch™ADSL/POTS variant)
ADSL over ISDN for a SpeedTouch™ ADSL/ISDN variant)
ADSL/RE-ADLS2/ADSL2/ADSL2+ for both ADSL over POTS and ADSL over
ISDN
Physical interfaces
ꢀ
ꢀ
WAN: One RJ-11 port for ADSL/POTS or ADSL/ISDN connection
LAN: Four RJ-45 ports to connect up to 4 PCs to a 10/100 Base-T Ehternet
network
ꢀ
Power inlet
LEDs
LED indicators for all interfaces
Reset button
One recessed reset button for restoring the default settings
Power requirement Power supply: 15V AC, 1000mA
E-DOC-CTC-20050429-0100 v1.0
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
1.1.2 Software Features
ADSL compliance
ꢀ
ꢀ
If POTS in overlay: G. handshake, Full Rate ADSL, G.dmt, G.lite (splitterless
ADSL), ADSL2, RE-ADSL and ADSL2+
If ISDN in overlay: G.handshake, G.dmt, ADSL2, RE-ADSL and ADSL2+
ATM features
ꢀ
ꢀ
ꢀ
Up to 16 simultaneous PVCs, allowing multiple simultaneous destinations
ATM QoS per PVC: CBR, VBR-rt, VBR-nrt, UBR
RFC 1483 / 2684 multiprotocol encapsulation over AAL5 / ATM: both LLC /
SNAP and VC-based multiplexing supported
Bridging features
ꢀ
ꢀ
ꢀ
Multiport self-learning transparent bridge per IEEE 802.1D for LAN interconnect
Remote bridge ports are isolated from each other
Pre-defined bridge filters to WAN (no filter, no CPE-to-WAN broadcast, PPPoE
only) and to LAN (no filter, multicast filter)
Routing features
Services
ꢀ
ꢀ
ꢀ
Multi-port (up to 16 PVCs) router
Static routing, automatic routes (PPP, LAN)
IP address multi-homing
ꢀ
UPnP with NAT traversal capability:
ꢀ
ꢀ
enables game technologies (Xbox live, Direct X, and many others)
enables conferencing functions of Microsoft Messenger
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Transparent bridging (IEEE802.1D)
PPPoE routing/bridging with integrated PPP Relay
PPPoA routing, PPPoA-to-PPTP relaying
IP routing with static routing, packet classified routing and residential RIP
Hyper-NAT with virtual server mapping (for instance for Web, FTP, Mail
servers) and ALGs (such as NetMeeting, MSN Messenger, VPN passthrough,
and others)
ꢀ
ꢀ
Quality of Service:
ꢀ
IP QoS
Integrated Dynamic DNS client
Security
ꢀ
ꢀ
ꢀ
ꢀ
PAP (RFC1334), CHAP (RFC1994) for PPP session
Integrated Stateful Inspection Firewall, Intrusion Detection
Parental Control, URL Filtering
Multi-level SpeedTouch™ access policies, Digest Authentication
Configuration
ꢀ
ꢀ
ꢀ
ꢀ
Home Install Wizard, Easy Setup wizard
Intuitive web-based GUI (HTTP/HTTPs)
Advanced configuration via telnet - Command Line Interface (CLI)
Remote management access control
E-DOC-CTC-20050429-0100 v1.0
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
Management
ꢀ
ꢀ
ꢀ
ꢀ
Multi-level user protection, Event logging
DHCP server, client and relay, DHCP-to-PPP spoofing
DNS server, client and relay
Time synchronization:
ꢀ
SNTPv1, SNTPv2, SNTPv3 and SNTPv4
ꢀ
ꢀ
ꢀ
System logging
SNMPv1 agent with MIB-II
Firmware upgradeable via upgrade wizard on Setup CD
E-DOC-CTC-20050429-0100 v1.0
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
1.2 SpeedTouch™ LED Behaviour
Front panel LEDs The SpeedTouch™ is equipped with a number of LEDs on its front panel, indicating
the state of the device during normal operation.
Following table shows the meaning of the different LEDs:
Indicator
Name
Description
Colour State
Power
Green
Red
On
On
Power on, normal operation
Power on, self-test failed, indicating
device malfunction
Orange
Off
On
Bootloader active
Power off
Ethernet
DSL
Green
Flashing
On
Ethernet activity
Ethernet connection, no activity
No Ethernet connection
Pending DSL line synchronisation
DSL line synchronised
No DSL line
Off
Green
Flashing
On
Off
Internet
Green
Flashing
On
Internet activity
Internet connectivity, no activity
Internet connection setup failed
No Internet connection
Red
Off
On
E-DOC-CTC-20050429-0100 v1.0
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
1.3 How to Access your SpeedTouch™
Access methods Your SpeedTouch™ is accessible in one of following ways:
Access Method
Can be used to:
Web
Configure your SpeedTouch™ via HTTP or
HTTPS.
For more information, see “1.3.1 Access via
Command Line Interface (CLI)
File Transfer Protocol (FTP)
Remote Assistance
Fine tune your SpeedTouch™ configuration.
For more information, see “1.3.2 Access via
Backup and restore data on your SpeedTouch™.
For more information, see “1.3.3 Access via
Allow a remote user to help you configuring
your SpeedTouch™.
For more information, see “1.3.4 Remote
E-DOC-CTC-20050429-0100 v1.0
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
1.3.1 Access via the Web Interface
Procedure
To access the SpeedTouch™ via the web interface:
1
2
Open a web browser.
In the address bar type your SpeedTouch™’s IP address or DNS host name, by
default that is ‘http://speedtouch.lan’ or ‘192.168.1.254’.
You can access the pages via the http protocol. For remote assistance
the secure version, https, in combination with certificates is used;
provide your ISP with the https link, user name and password before
he can log on to the pages. For more information, see “1.3.4 Remote
3
to all the configurable aspects of the SpeedTouch™.
For more information on the web pages, see “4 SpeedTouch™ Web Interface” on
E-DOC-CTC-20050429-0100 v1.0
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
1.3.2 Access via CLI
Command Line
Interface (CLI)
You can access the Command Line Interface (CLI) via:
ꢀ
A Telnet session
This requires that TCP/IP connectivity exists between the host from which the
Telnet session is opened and the SpeedTouch™. Your SpeedTouch™ and the
connected PC must have an IP address in the same subnet.
ꢀ
Quote site commands (over FTP)
For information on CLI commands, see the SpeedTouch™ CLI Reference Guide.
E-DOC-CTC-20050429-0100 v1.0
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
Telnet session
Proceed as follows:
1
Open a telnet application.
You can use the Command Prompt window.
In Windows XP for instance:
1
2
On the Windows task bar, click Start.
Select (All) Programs > Accessories > Command Prompt.
2
Connect to your SpeedTouch™. .
In the Command Prompt window:
At the prompt, type telnetfollowed by the IP address of your
SpeedTouch™ (default is 192.168.1.254).
3
4
Enter your SpeedTouch™ security user name and password.
The default user is ‘Administrator’ and the default password is blank.
As soon as you’ve opened a session to the CLI, the SpeedTouch™ banner is
displayed, followed by the CLI prompt, as shown in the example below:
Username : Administrator
-----------------------------------------------------------------------
-
*
*
*
*
*
*
*
*
*
*
______ SpeedTouch
___/_____/\
/
/\\ Version 5.3
/ \\
_____/__
_/
//
_______//_______/
/ \
/\_____/___ \ Copyright (c) 1999-2005,
/
\
/\ \
THOMSON
\
/
/ _\/______
/
\
/ /
/ /
/ /
/\
/ _\__
/ / /\
__/
/ /
/
\
\
/
/
\_______\/
* /_/______/___________________/ /________/ /___/
* \ \ ___________ \ \ \ \
/\ \ \ \ \___\/
\ \
\ \________\/
\
/
\
\
*
*
*
*
*
*
*
*
*
\_\
\
/
\
\/
\_____/
/__________/
_____
/\
/
\
\
/
/
\
\
\
/
\
\
/_____\/
/___\/
\ /
/____/
\
\
\
/
\
\
/___\/
\____\/
-----------------------------------------------------------------------
{Administrator}=>
E-DOC-CTC-20050429-0100 v1.0
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
1.3.3 Access via FTP
File Transfer Protocol
You can access the file system of the SpeedTouch™ via the File Transfer Protocol
(FTP), in order to:
(FTP)
ꢀ
ꢀ
Restore or backup configuration files, templates or language packs.
Upgrade your configuration or firmware.
File system
The SpeedTouch™ file system is stored on nonvolatile memory, and contains the
SpeedTouch™ software, service template files and (optionally) default setting files.
FTP session To open an FTP session:
1
Open a Command Prompt window.
In Windows XP for instance:
1
2
On the Windows task bar, click Start.
Select (All) Programs > Accessories > Command Prompt.
2
3
At the prompt, type ftpfollowed by the IP address of your SpeedTouch™
(default is 192.168.1.254).
Enter your SpeedTouch™ security user name and password.
The default user is ‘Administrator’ and the default password is blank.
The example below shows an FTP session to the SpeedTouch™ file system:
4
File system structure
The structure of the file system is very simple: It consists of a single root directory
called root and a subdirectory called dl.
ꢀ
The root directory contains:
ꢀ
ꢀ
all the necessary files for the SpeedTouch™ to boot correctly
the dl directory
ꢀ
The dl (download) directory contains the software image.
If you made changes to the SpeedTouch™ configuration and saved
them, a user.ini configuration settings file is created in the dl
subdirectory.
E-DOC-CTC-20050429-0100 v1.0
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
File system access
On the different directories you have following privileges:
rights
Directory
root
Access rights
NO read/write
read/write
dl
Common FTP
commands
Depending on the access rights you have on a directory, you can use one of
following commands:
Command...
You can use to...
cd
access another directory than the one currently open.
Example: ftp>cd dl.
dir
list the directory files.
Example: ftp>dir.
bin
set the transfer mode to ‘binary’.
turn on the hashing option.
hash
put
upload files.
Example: ftp>put C:/MyBackupFiles/user.ini.
A configuration file must be uploaded to the dl directory.
get
download files.
Example: ftp>get user.ini.
Downloading the configuration file must be done from the dl
directory.
delete
bye
delete files.
quit FTP.
E-DOC-CTC-20050429-0100 v1.0
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
FTP file transfer To allow correct file transfers, set the transfer mode to “binary”: At the ftp prompt,
type bin and press Enter.
Turn on the hashing option to see the progression of the file transfer: At the
ftp prompt type hash and press Enter.
Example:
/home/doejohn{1}$ftp 192.168.1.254
Connected to 192.168.1.254
220 Inactivity timer = 120 seconds. Use 'site idle <secs>' to change.
Name (192.168.1.254:doejohn):
331 SpeedTouch™ (00-90-D0-01-02-03) User 'doejohn' OK. Password requir
ed.
Password : ######
330 OK
ftp>
ftp>bin
200 TYPE is now 8-bit binary
ftp>
ftp>hash
200Hash mark printing on (8192 bytes/hash mark).
ftp>cd dl
250 Changed to /dl
ftp>put C:\user.ini
200 Connected to 192.168.1.10 port 1271
150 Opening data connection for user.ini
226 File written successfully
ftp: 256 bytes sent in 0,000Seconds 256000,000Kbytes/sec.
ftp>
Quote site command
All the CLI commands can be executed from within an FTP session. Only complete
CLI commands (in other words, the complete command syntax with all the
parameters already specified) can be executed.
Example: To execute the CLI command :software cleanup: At the FTP prompt
type ‘quote site software cleanup’ and press Enter.
ftp> quote site software cleanup
200-
200 CLI command "software cleanup" executed
ftp>
For more information on CLI commands, see the CLI Reference Guide.
E-DOC-CTC-20050429-0100 v1.0
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Your SpeedTouch™
1.3.4 Remote Assistance
Remote access
You can make your SpeedTouch accessible from the Internet with regard to remote
support. This way, you can allow your helpdesk to access your SpeedTouch™
remotely.
Enabling remote access
To enable remote assistance:
1
Go to the SpeedTouch™ pages, as described in “1.3.1 Access via the Web
2
3
4
In the menu select Toolbox > Remote Assistance.
Click Enable Remote Assistance.
Provide the following parameters to your helpdesk:
ꢀ
ꢀ
ꢀ
URL (the HTTPS link)
User name
Password
5
Your ISP is now able to access your SpeedTouch™ via the secure HTTPs link in
combination with the provided certificate (a secure authentication mechanism).
For security reasons, after 20 minutes of inactivity, or on reboot, Remote
Assistance will be automatically disabled.
Disabling remote
access
To disable remote assistance:
1
Go to the SpeedTouch™ pages, as described in “1.3.1 Access via the Web
2
3
In the menu select Toolbox > Remote Assistance.
Click Disable Remote Assistance.
E-DOC-CTC-20050429-0100 v1.0
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Local Network Setup
2 Local Network Setup
Ethernet network
The Ethernet ports on the back panel of your SpeedTouch™ allow you to connect the
SpeedTouch™ to an existing 10 or 100 Base-T Ethernet network or to a computer
with installed Ethernet card.
Using the SpeedTouch™ Ethernet switch, you can create a local Ethernet network of
up to four devices, without needing extra networking devices
In the SpeedTouch™ package, a yellow full-wired straight-through RJ-45/RJ-
45 Ethernet cable is included.
Standard wiring Use the yellow Ethernet cable provided to wire your computer’s Ethernet port to the
one of the SpeedTouch™’s Ethernet ports.
procedure
The Ethernet cable can also be used to wire any Ethernet port of your SpeedTouch™
to an external hub or switch.
Please follow the installation instructions supplied with the external hub or
switch for connections and Ethernet cabling.
E-DOC-CTC-20050429-0100 v1.0
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Local Network Setup
Device settings Once you’ve connected a device, you are able to personalise its settings:
1
2
3
Go to the SpeedTouch™ web pages.
In the menu select Home Network > Devices.
Click the name of your device, or if the device’s settings haven’t been
personalised yet, click the MAC address of the device.
4
5
On the top right, click Configure.
Now you can change the device’s name, lock its IP address and assign
applications and services to the device.
Ethernet link check
Depending on the SpeedTouch™ model, LED indicators allow you to check your
E-DOC-CTC-20050429-0100 v1.0
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
3 Internet Connectivity Dial-In Clients
Introduction For setting up initial Internet connectivity, using the Home Install Wizard on the
Setup CD or the embedded Easy Setup, refer to the provided Installation and Setup
Guide.
Access methods Depending on the configuration of the SpeedTouch™ you may have:
ꢀ Direct access:
As soon as the initial configuration has been done, immediate and uninterrupted
WAN access is provided.
In case of direct access, the remote organisation might ask for a user
name and password on an Internet welcome page.
ꢀ Dial-in access:
Access must be explicitly established, that is by “dialling” into a Broadband
Remote Access Server (BRAS).
Depending on the SpeedTouch™ configuration, dial-in access is provided via the
SpeedTouch™’s Routed PPPoA or Routed PPPoE packet services with
embedded PPP client.
Connection protocols The applied connection protocol model depends on the service profile you selected to
configure the SpeedTouch™ and should correspond with the Service Provider’s
requirements. If your ISP provides PPPoE for instance, you should configure PPPoE.
More information on connection protocols can be found in the Internet Connection
Configuration Guide.
Dial-in clients
There are different ways of dialling in, depending on the operating system on your PC
and your preferences.
Dial-in method:
can be used on
following operating
system:
For more information,
see:
Embedded PPP dial-in client:
Dial-in client on
embedded pages
MS Windows, Mac, unix,
other
MS Windows XP IGD
Control Agent for UPnP
MS Windows XP
Host PPP dial-in client for a SpeedTouch™ configured in pure bridging mode:
MS Windows XP
Broadband connection
MS Windows XP
Mac OS X PPPoE dial-in
client
Mac OS X
E-DOC-CTC-20050429-0100 v1.0
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
Embedded PPP dial-in The SpeedTouch™’s embedded PPP dial-in client allows you to establish an Internet
connection for computers residing on your local network, using only one computer of
the network to control the client.
clients
If this computer runs:
ꢀ
Any Operating System
you can always use the SpeedTouch™ web pages.
ꢀ
MS Windows XP
you can use MS Windows XP’s Internet Gateway Device Control Client.
Broadband host PPPoE You can also connect to the Internet using a Broadband PPPoE dial-in application.
The PPP over Ethernet connection scenario provides PPP-like dial-in behaviour over
the virtual Ethernet segment.
dial-in clients
To be able to use a broadband dial-in application on your computer for connecting to
the Internet, the SpeedTouch™ needs to be configured for Bridged Ethernet or Routed
PPPoE (with PPPoE relay) via the SpeedTouch™ Home Install Wizard on the Setup CD
or the embedded Easy Setup.
If this computer runs:
ꢀ
MS Windows XP
you can use the MS Windows XP broadband dial-in client. See “3.3 MS
Windows XP BroadBand Connection” on page 25 for more information.
ꢀ
Mac OS X
you can use a Mac OS X broadband dial-in client. See “3.4 Mac OS X PPPoE
Dial-in Client” on page 29 for more information.
- or -
ꢀ
A broadband PPPoE dial-in client provided by your Service Provider to connect
to the Internet
Upon availability of OS-specific PPPoE dial-in client applications, the
latter method is Operating System independent.
For PPPoE session connectivity from a Mac OS 8.6/9.x, an MS
Windows 95/98(SE)/ME/2000 or a Linux system, a host PPPoE dial-in
application is mandatory.
E-DOC-CTC-20050429-0100 v1.0
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
3.1 SpeedTouch™ Web Pages
Introduction As the SpeedTouch™ web pages are controllable from any Operating System with an
installed web browser, the method to establish PPP sessions described below you
can use on any computer system.
For more information on Internet connection setup, see the provided Installation and
Setup Guide.
Starting an Internet Proceed as follows:
session
1
Open a web browser on your computer and browse to the SpeedTouch™ web
information):
By default the SpeedTouch™ shows you the Home page.
Click Connect at the appropriate broadband connection.
You might be requested to enter your user name and password.
2
3
As a result SpeedTouch™’s embedded PPP dial-in client establishes the Internet
connection.
Now you can surf the Internet.
Monitoring your
Internet connection
You are able to overview and monitor your Internet connectivity as long as the
session is running via:
ꢀ
The SpeedTouch™ System Information page: see “4.3.1 Information” on
ꢀ
The SpeedTouch™ Diagnostics task: see “4.4.1 Connectivity Check” on
E-DOC-CTC-20050429-0100 v1.0
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
Terminating an Internet
session
To close an active PPP connection:
1
2
Go to the SpeedTouch™ Home page.
Click Disconnect at the appropriate broadband connection.
As a result the SpeedTouch™’s embedded PPP dial-in client will close the Internet
connection. The Internet Link status will change to Disconnected and your PC is off-
line.
E-DOC-CTC-20050429-0100 v1.0
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
3.2 IGD Control Agent
Introduction MS Windows XP users can easily establish PPP sessions, thanks to MS Windows
XP’s Internet Gateway Device (IGD) Discovery and Control Client that allows you to
control the SpeedTouch™ directly from you PC.
The IGD control client only allows to connect or to disconnect a fully
configured connection.
Preconditions Following conditions must be met:
ꢀ
Following subcomponents of Windows XP’s Networking Services must be
added to your Windows XP system:
ꢀ
ꢀ
IGD Discovery and Control Client (see “ Adding IGD Discovery and
ꢀ
UPnP™ must be enabled on your SpeedTouch™. To enable UPnP, see
Starting an Internet Proceed as follows:
session
1
2
3
In the Windows task bar, click Start.
Select (Settings >) Control Panel.
The Control Panel window appears. Go to (Network and Internet Connections
>) Network Connections.
4
The Network Connections window appears:
You will find an Internet Gateway icon, representing the SpeedTouch™ IGD
Internet connection ability.
5
6
Double-click the Internet Connection icon.
As a result the SpeedTouch™’s embedded PPP dial-in client establishes the
Internet connection. The Internet Gateway icon displays connected and your
PC is online.
You can open a web browser and surf the Internet.
E-DOC-CTC-20050429-0100 v1.0
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
Internet connection As long as the SpeedTouch™’s embedded PPP dial-in client is connected, you are able
to overview the connection status and some counters by double-clicking the Internet
Connection icon in your PC’s Network Connections window:
status
Terminating an Internet
session
Proceed as follows:
1
2
In the Windows task bar, click Start.
Select (Settings >) Control Panel > (Network and Internet Connections >)
Network Connections.
3
4
In the Network Connections window, right-click the Internet Connection icon
and select Disconnect to close the session.
You can also double-click the icon. Then the Internet Connection
Status window will appear on which a Disconnect button is available
to close the session.
As a result the SpeedTouch™’s embedded PPP dial-in client will close the
Internet connection. The Internet Gateway icon displays Disconnected and
your computers are off-line.
E-DOC-CTC-20050429-0100 v1.0
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
3.3 MS Windows XP BroadBand Connection
Prerequisites
To be able to use the MS Windows XP BroadBand Connection, your SpeedTouch™
must be configured for either:
ꢀ
ꢀ
Bridging, or
PPPoE Relay
Configuring a Proceed as follows:
broadband connection
1
2
On the Start menu, click (Settings >) Control Panel.
The Control Panel window appears. Go to (Network and Internet Connections
>) Network Connections.
3
In the Network Tasks menu, click Create a new connection.
The New Connection Wizard appears:
Click Next.
4
5
6
Select Connect to the Internet and click Next.
Select Set up my connection manually and click Next.
Select Connect using a broadband connection that requires a user name and
password and click Next.
7
Give a name to the connection you are creating, for example YourISP:
E-DOC-CTC-20050429-0100 v1.0
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
8
Select whether the connection will be available to any user or only to yourself:
9
Fill in the Internet account information. This information should be provided by
your service provider:
10 At the end of the configuration the following window appears:
Click Finish to complete the configuration.
The Connect YourISP window (see below) appears.
E-DOC-CTC-20050429-0100 v1.0
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
Starting a broadband Proceed as follows:
Internet session
1
On the Start menu, point Connect To and click the name of the connection
you’ve created, for example YourISP.
If you are using the Classic Start menu click Start > Settings >
Network (and Dial-up) connections > YourISP.
2
The Connect YourISP window appears:
3
If requested, enter user name and password for your user account at the
Service Provider.
4
5
Click Connect.
As soon as the connection is established, the Connection message box and
Dialup window are minimised into an icon in the notification area:
6
You can open your web browser and surf the Internet.
E-DOC-CTC-20050429-0100 v1.0
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
Terminating a Proceed as follows:
broadband Internet
session
1
On the Start menu, point Connect To and click the name of the connection
you’ve created, for example YourISP.
If you are using the Classic Start menu go to Start > Settings >
Network (and Dial-up) connections > YourISP.
2
The YourISP Status window appears:
3
4
Click Disconnect.
The connection is released. As a result no Internet connectivity exists any
more.
E-DOC-CTC-20050429-0100 v1.0
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
3.4 Mac OS X PPPoE Dial-in Client
Prerequisites
To be able to use the MS Windows XP BroadBand Connection, your SpeedTouch™
must be configured for either:
ꢀ
ꢀ
Bridging, or
PPPoE Relay
Configuring a Proceed as follows:
broadband connection
1
2
3
On the Apple menu, click System Preferences.
In the System Preferences window, click the Network icon.
The Network window appears. Make sure Built-in Ethernet is selected in the
Show list and click the PPPoE tab:
4
5
Enter the Account Name and Password provided by your Service Provider.
Select Save password in case you want the computer to remember
the password for this account name.
Optionally you can enter a name for this connection in the Service
Provider field. All other fields may stay empty.
Click Apply Now.
E-DOC-CTC-20050429-0100 v1.0
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Internet Connectivity Dial-In Clients
Starting a broadband Proceed as follows:
Internet session
1
Click the Internet Connect dockling.
If the Internet Connect dockling is not available, go to the Applications
folder on the system startup disk and double-click Internet Connect.
2
The following window appears:
Make sure Built-in Ethernet is selected in the Configuration list.
3
If needed, enter user name and password for your user account at the Service
Provider.
4
5
Click Connect.
As soon as the connection is established you can open your web browser and
surf the Internet.
Terminating a Proceed as follows:
broadband Internet
session
1
Click the Internet Connect dockling.
If the Internet Connect dockling is not available, go to the Applications
folder on the system startup disk and double-click Internet Connect.
2
The following window appears:
Make sure Built-in Ethernet is selected in the Configuration list
Click Disconnect.
3
4
The connection is released. As a result no Internet connectivity exists any
more.
E-DOC-CTC-20050429-0100 v1.0
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4 SpeedTouch™ Web Interface
Introduction The SpeedTouch™ comes with embedded HTML pages, providing an interface to the
software installed on the device. It allows easy setup and management of the
SpeedTouch™ via your web browser form any PC connected to the SpeedTouch™.
SpeedTouch™
documentation
Consult:
The SpeedTouch™ Installation and Setup Guide
for more information on setup and installation procedures.
ꢀ
E-DOC-CTC-20050429-0100 v1.0
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.1 Navigation
Navigation components
The SpeedTouch™ web interface consists of following components:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Navigation bar
Notification area
Language bar
Menu
Tasks
E-DOC-CTC-20050429-0100 v1.0
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.1.1 Menu
Menu items The menu is located on the left side of the page and consists of the following menu
items:
ꢀ
ꢀ
ꢀ
Provides basic information on the SpeedTouch™.
Allows you to view/configure your broadband connections.
Allows you to assign games or applications to a device and secure your
Internet connection.
ꢀ
Allows you to manage your local network.
Collapsing and
expanding the menu
You are able to collapse/expand the menu by clicking the arrow located on the top
of the menu.
E-DOC-CTC-20050429-0100 v1.0
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.1.2 Language Bar
Language bar The language bar is located under the SpeedTouch™ logo and allows you to change
the language of the SpeedTouch™ web interface.
The language bar will only be shown if more than one language is available.
!
E-DOC-CTC-20050429-0100 v1.0
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.1.3 Navigation Bar
Navigation bar The navigation bar is located on the top of the page and allows you to:
ꢀ
View the current user name.
Click this name to change your password or switch to another user.
ꢀ
ꢀ
View the current position on the SpeedTouch™ web interface.
Get context related Help information.
Display level Depending on the page you are viewing following buttons will be available:
ꢀ
ꢀ
Overview to view a summary of the current status or configuration.
Details to view more detailed information on the current status or
configuration.
ꢀ
Configure to change the current settings.
E-DOC-CTC-20050429-0100 v1.0
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.1.4 Notification Area
ꢀ
ꢀ
ꢀ
Error messages indicated by a red traffic light.
Warnings indicated by an orange traffic light.
Information indicated by a green traffic light.
If none of these events occur, the notification area will not be shown.
E-DOC-CTC-20050429-0100 v1.0
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.1.5 Tasks
Tasks To allow a swift configuration of your SpeedTouch™, some pages may offer you a
number of related tasks. These tasks will guide you to the page where you can
perform the selected task.
E-DOC-CTC-20050429-0100 v1.0
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.3 SpeedTouch
The SpeedTouch menu The SpeedTouch menu consists of following items:
ꢀ
ꢀ
ꢀ
ꢀ
The SpeedTouch page The SpeedTouch page gives you some basic information on the SpeedTouch™:
ꢀ
ꢀ
Product Information
E-DOC-CTC-20050429-0100 v1.0
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.3.1 Information
Information The Information page summarizes important information on your SpeedTouch™. You
may need this information when you contact your helpdesk.
E-DOC-CTC-20050429-0100 v1.0
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.3.2 SpeedTouch™ Easy Setup
Easy Setup Wizard This wizard helps you configure your SpeedTouch™ Internet connection.
To configure the SpeedTouch™ using the SpeedTouch™ Easy Setup wizard:
1
2
3
On the left menu, click SpeedTouch.
In the Pick a task... list, click Set up.
The Easy Setup wizard will now guide you through the configuration of your
SpeedTouch™.
E-DOC-CTC-20050429-0100 v1.0
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.3.3 Restart
Accessing the Restart Proceed as follows:
page
1
2
On the left menu, click SpeedTouch.
In the Pick a task... list, click Restart.
Restarting your Proceed as follows:
SpeedTouch™
1
2
3
Click Yes, restart my SpeedTouch.
The SpeedTouch™ restarts.
E-DOC-CTC-20050429-0100 v1.0
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.3.4 Configuration
Overview The Overview page displays the current configuration of your SpeedTouch™.
Details The Details page displays more detailed information on the current configuration of
your SpeedTouch™.
Configure
The Configure page allows you to change the current configuration.
If you want to:
ꢀ
Reconfigure your SpeedTouch™:
Click Configuration Wizard under Service Configuration. For more information,
ꢀ
Configure the time settings of your SpeedTouch™:
ꢀ
Select Auto-configuration if you want the SpeedTouch™ to use a time
server to synchronise its clock to a dedicated time server.
ꢀ
Clear Auto-configuration to manually configure the SpeedTouch™ time
settings.
ꢀ
Disable/enable web browsing interception or set it to automatic.
If you disable web browsing interception or set it to automatic you will
!
Click Apply to save your settings.
E-DOC-CTC-20050429-0100 v1.0
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.3.5 Backup & Restore
Introduction This page allows you to:
ꢀ
ꢀ
Save your current configuration.
Restore a previously saved configuration.
Accessing the Backup Proceed as follows:
& Restore page
1
2
3
On the SpeedTouch menu, click Configuration.
Click Configure.
In the Pick a task... list, click Save or Restore Configuration.
Saving your current Proceed as follows:
configuration
1
2
3
Click Backup Configuration Now.
Click Save.
Choose a location to save your backup file and click Save.
Restoring a previously
saved configuration
Proceed as follows:
1
2
3
4
5
Click Browse.
Select the configuration file you want to restore and click Open.
Click Restore Configuration Now....
The SpeedTouch™ loads your configuration and restarts.
E-DOC-CTC-20050429-0100 v1.0
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.3.6 Reset to Factory Defaults
Introduction This page allows you to reset the SpeedTouch™ to return to the initial configuration
of your SpeedTouch™. All your changes will be deleted.
Accessing the Reset to
Proceed as follows:
Factory Defaults page
1
2
On the left menu, click SpeedTouch.
In the Pick a task... list, click Return to Factory Default Settings.
Resetting the
SpeedTouch™ to
factory defaults
If you want to reset your SpeedTouch™ to factory defaults, click Yes, reset my
SpeedTouch.
If you reset your SpeedTouch™ to factory default settings, all active
!
connections will be disconnected.
E-DOC-CTC-20050429-0100 v1.0
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.3.7 Event Logs
Event Logging
The Event Logs page summarizes the latest events recorded on your SpeedTouch™.
Recorded Events table
The Recorded Events table gives you an overview of the latest event logs that have
been recorded since power on. The first column of the table indicates the importance
of the event log
Indicator Description
Informational
Warning
Error
The Category list allows you to filter the events shown in the Recorded Events
table. For example, by clicking Security you can view all security related events, for
example generated by the SpeedTouch™ firewall.
E-DOC-CTC-20050429-0100 v1.0
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.3.8 Update
Updating the The Update page allows you to:
SpeedTouch™ system
software
ꢀ
ꢀ
ꢀ
View System Information.
View information on the current System Firmware.
Update your SpeedTouch™ from a remote server.
Use this option if you want to have yourSpeedTouch™ check on the internet for
new firmware and update if it found one.
ꢀ
Update from a PC.
Use this option if you want to install on your SpeedTouch™ that is located on
the PC.
E-DOC-CTC-20050429-0100 v1.0
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.4 Broadband Connection
The Broadband The Broadband Connection menu consists of following menu items:
Connection menu
ꢀ
ꢀ
The Broadband The Broadband Connection page gives you a short status overview of the
connections configured on the SpeedTouch™.
Connection page
Click View more to see more information on the selected broadband connection.
If you configured a dial-up connection, you are able to establish/terminate
the connection by clicking Connect/Disconnect.
E-DOC-CTC-20050429-0100 v1.0
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.4.1 Connectivity Check
Introduction This page enables you to perform a connectivity check on an Internet service of your
SpeedTouch™.
Accessing the Proceed as follows:
Connectivity Check page
1
2
On the left menu, click Broadband Connection.
In the Pick a task... list, click Check connectivity to the Internet.
Checking you Internet Proceed as follows:
Connectivity
1
In the Internet Service to Check list, click the Internet service that you want to
check.
2
3
Click Check Connectivity.
The SpeedTouch™ lists the test results in the Test Results list.
Analysing the test If the test is successful, you will get a list of green check marks. Otherwise a red
cross will indicate which tests have failed.
results
E-DOC-CTC-20050429-0100 v1.0
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.4.2 DSL Connection
Overview Click Overview to view brief information on your DSL connection.
Details Click Details to view a more detailed information on your DSL connection.
E-DOC-CTC-20050429-0100 v1.0
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.4.3 Internet Services
Internet Services
information
The Internet Services page displays information on your Internet Connection(s).
If you configured a dial-up connection you are able to establish/terminate
the connection by clicking Connect/Disconnect.
To view more detailed information on a specific connection, click the View more...
link of the corresponding connection.
E-DOC-CTC-20050429-0100 v1.0
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.4.4 Internet Service Settings
Accessing the Internet Proceed as follows:
Service Settings page
1
2
On the Broadband Connection menu click Internet Services.
Click the View more link of the internet service you want to view.
Overview The Overview page gives you basic information on the selected Internet Service.
If you configured a connection you are able to establish/terminate the
connection by clicking Connect/Disconnect.
Details The Details page gives you more detailed information on the selected Internet
Service.
If you configured a dial-up connection you are able to establish/terminate
the connection by clicking Connect/Disconnect.
E-DOC-CTC-20050429-0100 v1.0
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5 Toolbox
The Toolbox menu The Toolbox menu consists of following menu items:
ꢀ
Allows you to make your SpeedTouch™ accessible for remote support.
ꢀ
Allows you to share services and games that you run in your private network
towards the internet.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Allows you to block/allow access to specific web sites.
Allows you to configure the security level of the SpeedTouch™ firewall.
Allows you to view the intrusions you are protected against.
Allows you to assign a DNS host name to your broadband connection(s).
Allows you to manage the users configured on your SpeedTouch™.
The Toolbox page
The Toolbox page gives you an overview of the available services and their current
status. You can click on the names of these services to go to the corresponding web
page.
E-DOC-CTC-20050429-0100 v1.0
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.1 Remote Assistance
Enabling Remote
Assistance
This page allows you to make your SpeedTouch™ accessible for remote support.
You must be connected to the Internet to be able to enable remote
assistance.
!
To use remote assistance:
1
2
3
If needed, type a password in the Password box.
Click Enable Remote Assistance.
Pass the information listed under:
ꢀ
ꢀ
ꢀ
URL
Username
Password
to your technical support, in order for them to be able to access your
SpeedTouch™.
Once the technical support is connected, no other connections are
possible.
4
The remote assistance session ends:
ꢀ
ꢀ
If the technical support disables remote assistance.
After 20 minutes of inactivity, or after a reboot, remote management.
E-DOC-CTC-20050429-0100 v1.0
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.2 Game & Application Sharing
Overview The Overview page summarizes the games and applications on a particular host on
your network, for which the SpeedTouch™ accepts connections coming from the
Internet.
Configure
The Configuration page allows you to:
ꢀ
Select Use UPnP to enable UPnP on the SpeedTouch™.
Universal Plug and Play is an architecture for transparent peer-to-peer
connectivity of PCs, intelligent appliances, and (wireless) devices. It
enables seamless operation of a wide range of games and messaging
applications.
ꢀ
ꢀ
Select Use Extended Security to only allow the creation of port maps.
Assign a game or application to a specific network device.
E-DOC-CTC-20050429-0100 v1.0
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.3 Defined Games & Applications
Accessing the Defined
Games & Applications
page
Proceed as follows:
1
2
In the Toolbox menu, click Game & Application Sharing.
In the Pick a task... list, click Modify a game or application.
The Defined Games & This page gives you an overview of the games and applications defined on your
SpeedTouch™. Each game or application can be assigned to a device on your local
network.
Applications page
To:
ꢀ
ꢀ
View the translation rules of a game or application, click the name of the rule.
Change the translation rules of a game or application, click the Edit link of the
the game or application.
E-DOC-CTC-20050429-0100 v1.0
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.4 Game or Application Definition
Accessing the Game or Proceed as follows:
Application Definition
page
1
2
3
In the Toolbox menu, click Game & Application Sharing.
In the Pick a task... list, click Modify a game or application.
Click the name of the game or application you want to view/change.
Overview This page gives you an overview of the port mappings used to allow this service or
game to be initiated from the Internet.
Consult the user’s guide or support pages of your application to know which
ports are being used by this application.
A service is made of one or more TCP/UDP port ranges. Each incoming port range
can be translated into a different internal (local network) port range. Port ranges can
be statically assigned to devices or dynamically assigned using an outgoing trigger.
Configure
Under:
ꢀ
Game or Application Name you can:
Change the name of the game or application.
ꢀ
Game or Application Definition you can:
Change the TCP/UDP port definition for this game or application.
Adding a Port Proceed as follows:
Translation rule
1
2
3
In the Protocol list, click the protocol the game or application uses.
In the Port Range box, type the port range the game or application uses.
In the Translate To... box, type the port range to which the SpeedTouch™ has to
translate the ports specified under Port Range.
4
If you want to make a dynamic translation rule you must specify a trigger
protocol and port.
As soon as the SpeedTouch™ receives outgoing traffic on this trigger
port, it will activate this translation rule.
5
Click Apply.
E-DOC-CTC-20050429-0100 v1.0
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.5 New Game or Application
Accessing the Game or Proceed as follows:
Application Definition
1
2
On the Applications page, click Game & Application Sharing.
In the Pick a task... list, click Create a new game or application.
Creating a new game or Proceed as follows:
application
1
2
Type the name of the game or application in the Name box.
Click:
ꢀ
Clone Existing Game or Application if you want to start from the port
mappings of the selected game or application.
ꢀ
Manual Entry of Port Maps if you want to manually configure the port
mapping for this game or application.
3
4
The SpeedTouch™ creates the game or application and takes you to the Game
or Application Definition page to configure the port mappings for this game or
application.
Enter the necessary port mappings and click Add.
E-DOC-CTC-20050429-0100 v1.0
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.6 Parental Control
Parental Control
The SpeedTouch™ allows you to block/allow particular web sites:
Based on the web site’s URL.
ꢀ
As within a web site lots of references can be made to other URLs, it is
recommended to use this feature in combination with content based
filtering.
ꢀ
ꢀ
Based on the web site’s content.
Redirect a web site to another web site.
If your administrator account is configured as default user, make sure to
configure a password for this account or change the default user. Otherwise
users on your local network can surf to your SpeedTouch™ to disable your
filtering rules.
!
Overview The Overview page displays:
ꢀ
ꢀ
The current Address Based Filtering rules.
The current Content Based Filtering configuration.
To view which content types are blocked/allowed, click Details. For more
Address based filtering rules have priority over content based filtering
rules.
!
Configure
The Configure page allows you to:
ꢀ
ꢀ
ꢀ
ꢀ
Content levels
Following content levels are available:
ꢀ
ꢀ
ꢀ
All:
Allow all categorized web sites.
Legal:
Allow all except illegal, extreme, spam and spyware web sites.
Teenagers:
Block illegal, adult, extreme, online ordering/gambling, spam and spyware web
sites.
ꢀ
ꢀ
Children:
Only allow children-save web sites.
BlockAll:
Block all categorized web sites.
E-DOC-CTC-20050429-0100 v1.0
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
Deny access to a Use this feature if:
specific web site
ꢀ
ꢀ
Allow is selected under Action for Unknown Sites.
Block is selected under Action for Unknown Sites and you want to make an
exception on an allow rule. For example: you are allowing “provider.com” but
you want to deny access to “mail.provider.com”.
ꢀ
A content category/group is allowed by Content Based Filtering and you want
to make an exception. For example: you are allowing Web Mail content but you
want to deny access to “mail.provider.com”.
Proceed as follows:
1
Type the URL of the web site you want to block (for example
“mail.provider.com”) in the Web Site box.
2
In the Action list, click:
ꢀ
ꢀ
Block if you want to block this web site.
Redirect if you want to redirect to another page. Type the address of the
redirect page in the Redirect box.
3
Click Add.
Allow access to a Use this feature if:
specific web site
ꢀ
ꢀ
Block is selected under Action for Unknown Sites
Allow is selected under Action for Unknown Sites and you want to make an
exception on a block/redirect rule. For example: you are blocking “bank.com”
but you want to allow access to “netbanking.bank.com”.
ꢀ
A content category/group is blocked by Content Based Filtering and you want
to make an exception. For example: you are blocking Finance / Investment
content but you want to allow access to “netbanking.bank.com”.
Proceed as follows:
1
Type the URL of the web site you want to allow (for example
“netbanking.bank.com”) in the Web Site box.
Click Allow in the Action list.
Click Add.
2
3
Redirect a web site Proceed as follows:
1
Type the URL of the web site you want to redirect (for example “cracks.am”) in
the Web Site box.
2
3
Click Redirect in the Action list.
Type the URL of the web site you want to redirect to (for example
“mycompany.com/internetpolicy.htm”) in the Redirect box.
4
Click Add.
E-DOC-CTC-20050429-0100 v1.0
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
Redirecting all web Proceed as follows:
sites
1
2
3
Type “*” in the Web Site box.
Click Redirect in the Action list.
Type the URL of the web site you want to redirect to (for example
“mycompany.com/internetpolicy.htm”) in the Redirect box.
4
5
Click Add.
Type the URL of the web site you want to redirect to (for example
“mycompany.com/internetpolicy.htm”) in the Web Site box.
6
7
Click Allow in the Action list.
Click Add.
Configure content Under Content Based Filtering you are able to:
based filtering settings
ꢀ
ꢀ
ꢀ
Enable/disable content based filtering.
Allow/block uncategorized web sites.
Select a content level in the Content Level list.
To change a content level definition, click the Edit link of the content
level you want to change. For more information, see “4.5.8 Content
E-DOC-CTC-20050429-0100 v1.0
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.7 Web Filtering Activation
Accessing this page Proceed as follows:
On the Toolbox menu, click Web Site Filtering.
In the Pick a task... list, click Activate Web filtering License.
1
2
Web Filtering Activation
page
This page allows you to:
ꢀ
ꢀ
Activate a Web Filtering evaluation license.
Activate a free 30-days Web Filtering evaluation license.
Standard license Proceed as follows:
activation
1
2
3
Click Standard.
In the License Key box, type the license key provided by your ISP.
Click Apply.
E-DOC-CTC-20050429-0100 v1.0
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.8 Content Level
Accessing this page Proceed as follows:
1
2
3
On the Toolbox menu, click Web Site Filtering.
Click Configure.
Click the Edit link of the content level you want to edit.
Overview This page gives you an overview of the different categories and their rules.
Following icons indicate whether the content type is allowed or not:
Icon Description
The category/group is allowed
The category/group is not allowed.
The group is partly allowed.
Configure
This page allows you to change:
ꢀ
ꢀ
ꢀ
The content level name.
The content level description.
The content level configuration.
E-DOC-CTC-20050429-0100 v1.0
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.9 New Content Level
Introduction This page allows you to create a new content level. To access this page:
1
2
3
On the Toolbox menu, click Web Site Filtering.
In the upper right corner, click Configure.
Under Pick a task..., click Create a new content level.
Procedure
To apply a new content level following actions must be performed:
1
2
3
4
You can create up to 16 content levels.
!
Content level creation
Proceed as follows:
1
2
In the Name box, type a name for the new content level.
In the Description box, type a short text to describe what this security level will
do.
3
Click Next.
Content level Proceed as follows:
configuration
1
2
The Configuration section becomes available.
Click:
ꢀ
Clone Existing Level to start from a previously created content level.
If no levels have been defined before, this option will not be
shown.
ꢀ
ꢀ
Black List to allow all web sites by default.
White List to block all web sites by default.
3
Click Next.
Content level definition Only web sites that match the selected content level will be allowed. Proceed as
follows:
1
If you want to:
ꢀ
ꢀ
ꢀ
ꢀ
Allow a category:
Select the check box next to the category name.
Allow an entire group:
Select the check box next to the group name.
Block a category:
Clear the check box next to the category name.
Block an entire group:
Clear the check box next to the group name.
2
Click Apply.
E-DOC-CTC-20050429-0100 v1.0
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
Content level activation To activate your new content level:
1
2
3
4
On the Toolbox menu, click Web Site Filtering.
In the upper right corner, click Configure.
In the Content Level list, select your new content level.
The new content level is now active.
E-DOC-CTC-20050429-0100 v1.0
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.10 Firewall
Overview The Overview page summarizes the overall security policy configured on your
SpeedTouch™.
Configure
The Configure page allows you to select the security level of the SpeedTouch™.
Select one of following security levels:
ꢀ
Block All: to protect your network from all attempts of incoming (from
untrusted site) connection requests and to perform checks on outgoing (from
trusted site) connections. This level is meant to prevent incoming malicious
traffic.
ꢀ
ꢀ
Standard: to protect your network from all incoming (from untrusted site)
connection requests while permitting safe outgoing connections. This is the
default.
Disabled: to allow all incoming and outgoing traffic. This does not mean the
complete SpeedTouch™ firewall is disabled. It means all traffic coming in on one
interface and going out on another is allowed, but access to the embedded
services of the SpeedTouch™ (as telnet, web interface,...) is only allowed for
clients residing on the LAN side, so the SpeedTouch™ itself stays protected.
ꢀ
High:
Use this Security Level to block all outgoing connections except well known
applications (DNS, HTTP, HTTPS, FTP, TELNET, IMAP, POP) and block all
incoming connections. Game & Application sharing is not allowed by the
firewall.
E-DOC-CTC-20050429-0100 v1.0
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.11 Intrusion Detection
Intrusion Detection
Your SpeedTouch™ is protecting your network against malicious intrusions. This page
shows you the intrusions you are protected against.
The Protected Intrusions table shows the number of times the SpeedTouch™ actively
protected your network against each intrusion since last statistics reset.
E-DOC-CTC-20050429-0100 v1.0
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.12 Dynamic DNS
What is Dynamic DNS
The Dynamic DNS service allows you to assign a dynamic DNS host name (e.g.
john.dyndns.org) to a broadband connection even if it is using a dynamic IP address.
As soon as the device gets a new IP address, the dynamic DNS server updates its
entry to the new IP address.
Overview Click Overview to view the different Dynamic DNS clients with their name,
hostnames, interface and IP address.
Configure
The Configure page allows you to assign a Dynamic DNS host name to a broadband
connection:
1
Create an account at the Dynamic DNS service of your choice, for example:
ꢀ
GnuDIP for Linux
2
3
On the Dynamic DNS page, click Configure.
Select Enabled.
4
5
If needed, click the broadband connection to which you want to assign the
Dynamic DNS hostname in the Interface list.
Type the user name and password of your Dynamic DNS service account in the
corresponding fields.
6
7
In the Service list, click your Dynamic DNS service.
In the Host box, type the host name you want to assign to this interface (for
example myspeedtouch.dyndns.org).
8
Click Apply.
E-DOC-CTC-20050429-0100 v1.0
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.13 User Management
Overview The Overview page gives you an overview of the currently configured users and their
privileges.
Clicking the name of a user allows you to edit his user account.
Configure
The Configure page allows you to:
ꢀ
ꢀ
ꢀ
Click Add to create a new user account.
Click Delete to remove a user.
Click Edit to change a user account.
E-DOC-CTC-20050429-0100 v1.0
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.14 Edit User
Accessing the User Edit Proceed as follows:
page
1
2
On the Toolbox menu, click User Management.
Under Local User Data, click on the name of the user you want to edit.
Editing a user account The Edit User page allows you to:
ꢀ
Click Reset Password to reset the password of the selected user to the user
name. So, if you reset the password of John his password will be “John”.
ꢀ
Change the administration privileges of the selected user.
You can not change the administration privileges of the account you
are logged on to.
!
E-DOC-CTC-20050429-0100 v1.0
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.15 Change Default User
Changing the default This page allows you to change the default user. If users browse to the
SpeedTouch™ web pages, they will be automatically logged in under this account.
user
To allow users to automatically log on under this account, this default user
account must be configured with a blank password.
!
E-DOC-CTC-20050429-0100 v1.0
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.5.16 Add User
Adding users This page allows you to add a new user.
Under User definition you can configure:
ꢀ
The name of the new user.
The password of the new user will be equal to the user name; for
!
example if the user name is John Doe, the password will be John Doe.
Also when resetting a user, the password will be changed into the user
name.
ꢀ
The administration privileges of the new user
You can only add users with less than or equal administration
privileges as yourself.
!
E-DOC-CTC-20050429-0100 v1.0
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.6 Home Network
Home Network Menu This menu consists of following items:
ꢀ
Allows you the view/configure the devices detected on your local network.
ꢀ
Allows you to view/configure the interfaces that are available on the
SpeedTouch™.
The Home Network
page
The Home Network gives you an overview of your SpeedTouch™ network.
Viewing client If you click a on client you will be able to:
information
ꢀ
ꢀ
View the client’s network settings.
Configure the client’s network settings by clicking Configure.
E-DOC-CTC-20050429-0100 v1.0
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.6.1 Devices
Overview The Overview page gives you an overview of the devices that are currently
connected to the SpeedTouch™ network. Click on a device name to get more
information on a specific device.
Configure
The Configure page gives you an overview of the devices that are currently
connected to the SpeedTouch™ network.
To:
ꢀ
Get more information on a specific device, click on the name of the device.
ꢀ
ꢀ
Edit a device from the Detected Device(s) list, click Edit.
Delete a device from the Detected Device(s) list, click Delete.
Once a device connects to the SpeedTouch™ network, it will remain
listed in the Detected Device(s) list until you delete it.
E-DOC-CTC-20050429-0100 v1.0
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.6.2 Device Settings
Accessing the device Proceed as follows:
settings page
1
2
On the Home Network menu, click Devices.
In the Detected Device(s), click the name of the device you want to view.
Overview The Overview page displays following information:
ꢀ
Information allows you to view:
ꢀ
Status shows whether the device is currently connected to the
SpeedTouch™ network.
ꢀ
ꢀ
Type shows the device type.
Connected To shows the interface to which the device is currently
connected.
ꢀ
ꢀ
Addressing allows you to view:
ꢀ
ꢀ
Physical Address shows the MAC address of the device.
IP Address Assignment shows whether the device is using a static or
dynamic IP address.
ꢀ
IP Address shows the current IP address of the device.
Connection Sharing:
Gives you an overview of the games or services that are currently assigned to
this device. Click the name of the game or service to view the used port
mappings.
Configure
The Configure page allows you to:
ꢀ
ꢀ
Change the device information.
Allow a game or service running on this device to be initiated from the Internet.
E-DOC-CTC-20050429-0100 v1.0
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.6.3 Assign Public IP
Introduction This page allows you to assign the public IP address of your Internet Connection(s) to
a specific device on your local network. You might want to do this if:
ꢀ
ꢀ
You do not want to use the Network Address Translation engine of your
SpeedTouch™.
This device is running server applications (web server,...) and you want it to be
accessible from the Internet.
You can also achieve this by creating a port mapping for the specified
server, as described in “4.5.2 Game & Application Sharing” on
ꢀ
This device has to be considered as the unique access point to your local
network (DMZ).
It is not recommended to use this feature as this device will loose all
security offered by the SpeedTouch™.
!
Accessing the Assign Proceed as follows:
Public IP page
1
2
On the Home Network menu, click Devices.
In the Pick a task... list, click Assign the public IP address of a connection to a
device.
Assigning the public IP
address to a device
Proceed as follows:
1
2
Click the Edit link of your Internet connection.
In the Device list, select the device you want to assign the public address to.
3
4
Click Apply.
The SpeedTouch™ prompts you that you will have to make some adjustments
as a result of the new configuration, click OK.
5
Release and renew the IP address of the device.
For more information, see your operating system’s user guide or help.
If needed, reassign server applications to this device.
6
E-DOC-CTC-20050429-0100 v1.0
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.6.4 Interfaces
Interfaces overview This page gives you an overview of the interfaces used on your SpeedTouch™. If you
want to know more on the network settings of a specific interface, click the name of
the interface you want to view.
E-DOC-CTC-20050429-0100 v1.0
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.6.5 Interface Settings
Overview The Overview page gives you an overview of the current interface settings.
Configure
The Configure page allows you to:
ꢀ
ꢀ
Change the IP address settings of the SpeedTouch™.
Change the DHCP IP address pool settings.
Before changing the DHCP pools, make sure that at least one IP
address of the SpeedTouch™ uses the same subnet as the IP addresses
in the DHCP pools.
!
Assigning a new IP Under IP Addresses:
address to the
SpeedTouch™
1
Type the IP address of your choice (for example 192.168.1.1) in the left text
box.
2
3
4
Type subnet mask in the right text box (for example 255.255.255.0).
Click Add.
Network devices using the same subnet mask can now access the
SpeedTouch™ using this IP address.
E-DOC-CTC-20050429-0100 v1.0
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
4.6.6 DHCP Pool
DHCP Pool This page allows you to create/change a DHCP pool.
Accessing the DHCP
Pool page
Proceed as follows:
1
2
On the Home Network menu, click Interfaces.
Click on the name of the interface of which you want to change the DHCP pool
settings.
3
Click Configure.
4
Under DHCP Pools click:
ꢀ
ꢀ
ꢀ
Add if you want to add a new DCHP pool.
Edit if you want to edit an existing DHCP pool.
Delete if you want to delete an existing DHCP pool.
This link will only be shown if there are more than one DHCP
pools.
E-DOC-CTC-20050429-0100 v1.0
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SpeedTouch™ Web Interface
The DHCP Pool page
Following settings are available for configuration:
ꢀ
ꢀ
ꢀ
Interface:
The SpeedTouch™ interface for which the DHCP pool applies.
Start Address:
The start IP address of the DHCP server’s address pool.
End Address:
The end IP address of the DHCP server’s address pool.
Both the start and end IP address define the IP address range used by
the DHCP server to assign leases.
ꢀ
ꢀ
ꢀ
Subnet Mask:
The subnet mask of the DHCP server’s address pool.
Server:
The SpeedTouch™ IP address used as DHCP server address.
Gateway:
The IP address that will be assigned to the DHCP clients as their default
gateway.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Primary DNS:
The IP address of the primary DNS server.
Secondary DNS:
The IP address of the secondary DNS server.
Primary WINS:
The IP address of the primary WINS server.
Secondary WINS:
The IP address of the secondary WINS server.
Lease Time:
The time for which the DHCP client is allowed to use the assigned IP address:
If Always give same address to DHCP clients the lease time will be
automatically set to Infinite.
ꢀ
Always give same address to DHCP clients:
Select this check box if you always want to use the same IP address for the
DHCP clients.
E-DOC-CTC-20050429-0100 v1.0
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Software Upgrade
5 Software Upgrade
Introduction This chapter describes how to upgrade the SpeedTouch™ system software or
firmware.
System software For the availability of new system software version packages you can:
upgrades availability
ꢀ
ꢀ
Click the SpeedTouch Maintenance link, available on the Setup CD menu.
Check for SpeedTouch™ upgrades at http://www.speedtouch.com/upgrade.
System software All system software packages for the SpeedTouch™ are digitally signed and
encrypted. Packages that may have become corrupted, or been altered in any way,
will not be accepted by the SpeedTouch™.
packages and security
This way the SpeedTouch™ or its service can never be corrupted or lost.
System software Depending on the Operating System your computer is running, you can upgrade your
SpeedTouch™ via:
upgrades
ꢀ
The SpeedTouch™ Upgrade Wizard (Microsoft Windows or Mac OS X); see
“5.1 Upgrade Wizard on Setup CD” on page 82 for more information.
Preliminary steps Before you start with upgrading the SpeedTouch™, always make sure:
ꢀ
To inform all people relying on the SpeedTouch™ services, that service may be
down for some short period.
ꢀ
The new system software file is stored on your local disk or another storage
device.
E-DOC-CTC-20050429-0100 v1.0
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Software Upgrade
5.1 Upgrade Wizard on Setup CD
Introduction The procedures described in this section are valid only in case:
ꢀ
ꢀ
You run an MS Windows Operating System or Mac OS X.
Your SpeedTouch™ and computer are properly connected through Ethernet.
During the upgrade procedure in most cases configuration settings are backed up by
the wizard and restored after uploading the system software.
Starting the Upgrade
Wizard
To launch the SpeedTouch™ Upgrade Wizard:
1
Insert the Setup CD in your computer’s CD-ROM or DVD-ROM drive. The
SpeedTouch™ CD menu will pop up automatically.
If not:
ꢀ
In MS Windows:
Click Run on the Start menu and enter the following path:
D:\Setup.exe where D stands for the drive letter of your CD-ROM
or DVD-ROM drive.
ꢀ
On Mac OS X
Double-click the CD icon and then double-click Menu.
2
3
4
Optionally, in the Choose Language window, select the language of your
choice and click OK.
The SpeedTouch™ safety instructions will be displayed in your default web
browser. Close the window.
Select I have read and I fully understand the Safety Instructions and
Regularity Information and click Continue.
5
6
7
In the SpeedTouch™ CD Menu, click SpeedTouch Maintenance.
Click Upgrade My SpeedTouch, to start the SpeedTouch™ Upgrade Wizard.
E-DOC-CTC-20050429-0100 v1.0
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Software Upgrade
Upgrade procedure
1
In the Welcome to the SpeedTouch Upgrade Wizard window, click Next.
2
The SpeedTouch™ Software License Agreement window appears.
You must accept before continuing. Click Yes to accept.
If you accepted this License Agreement in a previous upgrade, this
window will not be shown.
3
4
The SpeedTouch™ Upgrade Wizard will search for the SpeedTouch™ on the
network. A progress bar is displayed.
The SpeedTouch™ Upgrade Wizard should find your SpeedTouch™ device on
the local network. This is indicated by the following window:
If more than one device is found, a list of available devices will be provided. If
this is the case, select your SpeedTouch™ device and click Next.
If the wizard does not find any SpeedTouch™ on the network an error
window appears, refer to “6.1.2 Upgrade Troubleshooting” on
5
Enter your SpeedTouch™ security User name and Password.
E-DOC-CTC-20050429-0100 v1.0
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Software Upgrade
6
The following window shows the system software version currently active on
the SpeedTouch™ as well as one or more system software versions available on
the CD:
For more information on a found software version, click Firmware Details.
Select the appropriate system software version and click Next.
If your Service Provider has included a separate disk with dedicated
upgrade system software, click Have Disk to navigate to the location
of the appropriate file.
7
The following window will allow you to overview your selection. Click Next to
continue.
8
9
A progress bar will be displayed.
Finally, click Finish to close the wizard.
System software Via the identical procedure it is also possible - although not recommended - to
downgrade the SpeedTouch™ by uploading an older system software than the
current running version.
downgrade
However, be aware that functionality added by previous upgrades may be lost, that
system password settings may be lost as well as end-to-end connectivity and other
configuration settings.
In case of a system software downgrade, in step 6, you must specifically
acknowledge your decision before being able to proceed.
!
E-DOC-CTC-20050429-0100 v1.0
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Troubleshooting
6 Troubleshooting
Introduction This chapter suggest solutions for problems you may encounter while installing or
configuring your SpeedTouch™.
If the suggestions do not resolve the problem, look at the support pages on http://
www.speedtouch.com/support or contact your service provider.
For Internet connection troubleshooting, refer to the provided Installation and Setup
Guide.
E-DOC-CTC-20050429-0100 v1.0
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Troubleshooting
6.1 General SpeedTouch™ Troubleshooting
SpeedTouch™ does not
If none of the LEDs light up, make sure that:
work
ꢀ
ꢀ
The SpeedTouch™ is plugged into a power socket outlet.
You are using the correct power supply for your SpeedTouch™ device, that is
15V AC.
ꢀ
The power on the SpeedTouch™ is turned on via the push button on the back
panel.
SpeedTouch™
unreachable
In case your SpeedTouch™ is unreachable due to misconfiguration, you might
consider a hardware reset to factory defaults as described in “6.3 Reset to Factory
However, note that resetting the SpeedTouch™ to its factory settings will
revoke all the changes you made to the configuration.
!
Poor SpeedTouch™ Make sure that the SpeedTouch™ is installed and configured as instructed in the
Installation and Setup Guide or as instructed by the Service Provider.
performance
E-DOC-CTC-20050429-0100 v1.0
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Troubleshooting
6.1.1 Ethernet Troubleshooting
LAN LED does not light
up
Make sure that:
ꢀ
ꢀ
The LAN cable is securely connected to the 10/100Base-T port.
You are using the correct cable type for your Ethernet equipment, that is UTP
CAT5 with RJ-45 connectors.
E-DOC-CTC-20050429-0100 v1.0
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Troubleshooting
6.1.2 Upgrade Troubleshooting
Introduction While upgrading your SpeedTouch™ via the Upgrade Wizard on the Setup CD, you
might encounter one of following problems.
Upgrade via Setup CD
does not find any SpeedTouch™ on the network, an error window will appear, stating
your SpeedTouch™ has not been found.
In this case check that:
ꢀ
ꢀ
ꢀ
The SpeedTouch™ is turned on and fully initialised.
Your PC is correctly connected to the SpeedTouch™.
Your PC has a valid IP address. To check this in MS Windows:
1
2
3
4
5
6
In the Windows task bar, click Start.
Select Run...
Type cmd in the Open field.
Click OK. A black window will appear with a flashing cursor.
Type ipconfig and then press Enter.
Verify that your computer has a valid IP address, that is any address but
0.0.0.0.
ꢀ
ꢀ
No dedicated firewall device or router is placed between your PC and the
SpeedTouch™.
No personal firewall software is running on your PC.
To repeat the search for your SpeedTouch™, click Back or restart the wizard. As soon
as the wizard finds your SpeedTouch™, you can continue with the Upgrade Wizard.
E-DOC-CTC-20050429-0100 v1.0
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Troubleshooting
6.2 UPnP™ on Windows XP Systems
SpeedTouch™ not
Check on following:
detected by UPnP™ or
IGD Control Client
ꢀ
ꢀ
ꢀ
Make sure the UPnP™ and Internet Gateway Device Control Client Networking
components are added to your MS Windows XP system.
Your computer doesn’t support UPnP™ if you run an operating system other
than MS Windows XP and MS Windows Millennium.
Make sure that UPnP™ is not disabled in the SpeedTouch™ web page; see
Adding UPnP™ If you are running Microsoft Windows XP, it is recommended to add the UPnP™
component to your system.
Proceed as follows:
1
2
3
On the Start menu, click (Settings >) Control Panel.
The Control Panel window appears. Click Add or Remove Programs.
In the Add or Remove Programs window appears, click Add/Remove
Windows Components.
4
In the Windows Components Wizard, select Networking Services in the
Components list and click Details.
5
In the Networking Services window, select Universal Plug and Play or UPnP
User Interface and click OK.
6
7
Click Next to start the installation and follow the instructions in the Windows
Components Wizard.
At the end of the procedure the wizard prompts you that the installation was
successful. Click Finish to quit.
E-DOC-CTC-20050429-0100 v1.0
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Troubleshooting
Adding IGD Discovery Your MS Windows XP system is able to discover and control Internet Gateway
Devices (IGD), like the SpeedTouch™ on your local network. Therefore it is
recommended to add the IGD Discovery and Control client to your system.
and Control
Proceed as follows:
1
2
3
On the Windows task bar, click Start.
Select (Settings >) Control Panel > Add or Remove Programs.
In the Add or Remove Programs window, click Add/Remove Windows
Components.
4
The Windows Components Wizard appears:
Select Networking Services in the Components list and click Details.
5
In the Networking Services window, Select Internet Gateway Device
Discovery and Control Client and click OK.
6
7
Click Next to start the installation and follow the instructions in the Windows
Components Wizard.
At the end of the procedure the wizard prompts you that the installation was
successful. Click Finish to quit.
E-DOC-CTC-20050429-0100 v1.0
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Troubleshooting
6.3 Reset to Factory Defaults
Resetting your
SpeedTouch™
You might consider a reset to factory defaults as described below.
Be aware that a reset to factory defaults will revoke all configurational
!
changes you made to the SpeedTouch™.
You can choose between:
ꢀ
ꢀ
A reset to factory default settings deletes the configuration profile settings.
Therefore, after the reset, a reconfiguration of your SpeedTouch™ will be needed.
Hardware reset Proceed as follows:
1
2
Make sure the SpeedTouch™ is powered on.
Use a pen or an unfolded paperclip to push the recessed reset button on the
back panel. The reset button is marked with a red circle. Keep it pushed until
the power LED lights red - this will take about 7 seconds.
15VAC ON/OFF
1
2
3
4
3
4
Release the reset button.
The SpeedTouch™ restarts.
Software reset Proceed as follows:
1
2
3
4
5
Go to the SpeedTouch™ web pages.
In the menu select SpeedTouch > Configuration.
In the Pick a task... list, click Reset my SpeedTouch to default settings.
The SpeedTouch™ restarts.
The SpeedTouch™ returns to the SpeedTouch™ Home page (unless the IP
address of your computer is not in the same subnet as the default IP address of
the SpeedTouch™, being 192.168.1.254).
E-DOC-CTC-20050429-0100 v1.0
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Troubleshooting
E-DOC-CTC-20050429-0100 v1.0
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
©
H
O
2
.
l
e
d
.
E
C
-CT
C
2
4
9
0
.
Need more help?
Additional help is available online at www.speedtouch.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|