Mac Pro
ATI Radeon HD 4870 Card Cable
Replacement Instructions
Note: Follow these instructions carefully. Failure to do so could damage your equipment and
First Steps
void its warranty.
1
2
Shut down computer.
Wait 10 minutes.
Warning: Parts inside
computer can be very
hot. Allow computer
to cool down before
continuing.
3
Unplug all external
cables except power
cord.
4
5
Touch metal PCI cover
on back of computer.
Unplug power cord.
Opening the
Computer
1
Hold side access
panel and lift latch on
back of computer.
Warning: Edges of
access panel and
enclosure can be
sharp. Be careful
when handling.
2
Remove access panel
and place it on flat
surface covered by
soft, clean cloth.
© 2009 Apple Inc. All rights reserved.
073-1250 Rev. A
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If card is held in place by retention bar, complete steps 4 and 5. Otherwise, release small
locking clip at front of card’s connector by pushing clip up. Then go to step 6.
4
5
Press button on PCIe
fan.
Move fan to left,
which releases
retention bar.
6
7
Disconnect card’s
cables from
backplane board.
Holding card by top
corners, pull it up out
of slot and remove
card from computer.
Checklist for handling card:
•
•
•
•
When removing or installing card, handle it only by the edges. Do not touch its connectors
or any components.
Don’t rock card from side to side; instead, lift card straight up from connecotr to remove it,
and press card straight into slot to install it.
Don’t force card. If you meet a lot of resistance, pull card out. Check connector and slot for
damage or obstructions, then try inserting card again.
Pull card gently to see if it is properly connected. If it resists and stays in place and its gold
connectors are barely visible, card is connected.
© 2009 Apple Inc. All rights reserved.
073-1250 Rev. A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Disconnect cable
from card.
Installing the
Replacement Cable
and the Card
1
Connect replacement
cable to card.
2
Re-install card in slot.
Note: You can install
card in PCI slot 1, 2, or
3. Installed in slot 2, it
blocks slot 3. Installed
in slot 3, it blocks slot
4. Because of card’s
height, do not install
it in slot 4.
Note: Make sure
end of card goes
into correct card
guide. Then align
card’s connector
with expansion slot
and press down until
connector is inserted
all the way into slot.
3
Connect card’s cables
to connectors on
backplane board.
© 2009 Apple Inc. All rights reserved.
073-1250 Rev. A
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
If card is held in place
by retention bar, slide
PCIe fan to the right
to lock card in place.
Replace PCI bracket
and tighten screws.
Note: Slide bracket
under circled tab
before securing
screws.
Closing the
Computer
1
Replace access panel.
Note: Make sure
latch is up before you
replace panel. If latch
is down, panel will
not seat correctly.
2
Push latch down
to close and secure
access panel.
Warning: Never turn
on computer unless
all its internal and
external parts are in
place and it is closed.
Operating computer
when open or missing
parts can cause
damage or injury.
© 2009 Apple Inc. All rights reserved.
073-1250 Rev. A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Apple Inc.
© 2009 Apple Inc. All rights reserved.
This document is protected under U.S. Copyright Law and International Treaties, and no part of this
document may be reproduced in any form without written permission from Apple.
Apple is not responsible for typographical, printing, or inadvertent errors.
Apple Inc.
1 Infinite Loop
Cupertino, CA 95014-2084 USA
+ 1 408 996 1010
Apple, the Apple logo, and Mac are trademarks of Apple Inc., registered in the U.S. and other countries.
© 2009 Apple Inc. All rights reserved.
073-1250 Rev. A
6
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2009 Apple Inc. All rights reserved.
073-1250 Rev. A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|