American Standard Plumbing Product 2555602 User Manual

Installation  
Instructions  
TOWNSQUARE  
2555.602  
PRESSURE BALANCING BATH AND  
SHOWER-Built-in Diverter for TUB FILLER  
Thank you for selecting American-Standard...the benchmark  
of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--please  
read these instructions carefully before you begin.  
Certified to comply with ANSI A112.18.1  
M968789 Rev. 1.5  
Required Tools  
ROUGHING-IN DIMENSIONS  
To assure proper positioning in relation to wall, note  
roughing-in dimensions.  
1-5/8" TO 3-1/4"  
FINISHED WALL  
Phillips Screwdriver  
1
1/2" I.P.S.  
2" REF.  
OPTIONAL TO  
FINISHED FLOOR  
USUALLY BETWEEN  
65'' AND 78''  
Flat Blade Screwdriver  
OUTLETS 1/2" NPT  
8" REF.  
74" FOR  
HEAD CLEARANCE  
"SEE ILLUSTRATION"  
SHW  
Plumbers' Putty or Caulking  
5-5/8"  
7-1/2"  
TUB  
18"  
OPTIONAL  
1-3/4"  
7-1/4" REF.  
4"  
Channel Locks  
5-5/8"  
INLETS  
1/2" NPT  
1/2" COPPER  
1-3/4" REF.  
THREADED INLETS (STOPS)  
TOP OF  
TUB RIM  
Adjustable Wrench  
BOTTOM OF  
TUB  
Turn off water at main supply.  
CAUTION  
ROUGHING-IN  
1
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering,  
flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread  
sealant or Teflon tape on threaded connections.  
NOTE  
5
7
See Roughing-in diagram before starting.  
Connections are:  
1/2" female NPT for threaded inlets  
Connect RISER PIPE (1) to MANIFOLD (2)  
top outlet marked "SHR".  
Connect TUB FILLER PIPE (3) at bottom  
outlet marked "TUB".  
For proper positioning the finished wall  
must be within side wall of PLASTER  
GUARD (4).  
If the valve is installed on a fiberglass  
or other thin wall application, the  
1
2
PLASTER GUARD (4) can be used as a support.  
COLD  
4
Cut a 4" dia. hole in the shower stall.  
Drill two additional 1" holes to allow access  
to the stops.  
Remove PLASTER GUARD (4), rotate 180˚  
so that indicated screw holes fit MANIFOLD (2).  
Push CAP on valve, place ESCUTCHEON on and  
attach with screws.  
HOT  
3
Connect hot and cold water supplies.  
Cap off shower pipe (5) and tub filler pipe (6).  
For support, use pipe BRACES (7) secured to wooden braces.  
6
With valve turned off, turn on water supplies. Check for leaks.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALL HANDLE  
5
6
Install HANDLE BUSHING (1) onto CAP (2).  
7
Find correct position of HANDLE (3) and push HANDLE (3)  
onto VALVE STEM (4).  
Install HANDLE SCREW (5) and push in INDEX CAP (6).  
Check proper operation of HANDLE.  
5
6
Screw on DIVERTER KNOB (7).  
2
1
4
3
TO GAIN ACCESS TO VALVE FOR SERVICING  
Pull INDEX CAP, unscrew HANDLE SCREW and pull HANDLE off valve stem.  
Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON. Remove COVER by pulling straight out.  
Shut off water supply by either closing off main water supply, or closing off the hot and cold CHECK STOPS on valve, if present.  
VALVE LEAKS WHEN SHUT OFF  
Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and  
pull out PRESSURE BALANCING (5) unit.  
Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove  
CAPS (7) and check O-RINGS on inside of CAPS (7). Clean inside sealing surfaces of VALVE BODY (8).  
Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws.  
Turn on water supply and see above for installing TRIM and HANDLE.  
UNABLE TO MAINTAIN CONSTANT TEMPERATURE  
Remove PRESSURE BALANCE UNIT (5). Remove CAPS (7) and clean valve thoroughly.  
Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair  
Part M952100-0070A if balancing unit is defective.  
Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting.  
Top flange should butt-up against top of casting.  
BACK TO BACK INSTALLATION  
Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the  
large outlet port faces down.  
Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should  
butt up against top of casting.  
Reassemble FIXATION RING (4) and CARTRIDGE (1).  
ROTATE 180˚  
4
LARGE OUTLET  
1
5
6
8
INLETS  
7
BACK TO BACK INSTALLATION  
5
3
2
9
CARE INSTRUCTIONS:  
7
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A  
CLOTH WITH A COARSE SURFACE.  
M968789 Rev. 1.5  
Download from Www.Somanuals.com. All Manuals Search And Download.  

ADC Network Card DSX 4R RZX3 User Manual
Aiphone Telephone R24 A User Manual
Altinex Stereo Amplifier DAA0106 V0A2 User Manual
Aluratek Computer Drive AUHR200 User Manual
Atlona TV Mount AT 80120HD User Manual
Bacharach Home Security System 2772 0803 User Manual
Barco Projector R 9849999 User Manual
BC Speakers Speaker 18 RXB User Manual
Behringer Musical Instrument PMP3000 User Manual
Behringer Speaker System EX2200 User Manual