RONDALYN™
COUNTERTOP SINK
VITREOUS CHINA
BARRIER FREE
RONDALYN™ COUNTERTOP SINK
• Made from vitreous china
• Self-rimming with cutout template supplied
• Front overflow
• Faucet ledge
Shown with 4801.862 Amarilis/Heritage faucet
with Triune cross handles (not included)
❏ 0490.011 Faucet holes on 8" (203mm) centers
(illustrated)
❏ 0491.019 Faucet holes on 4" (102mm) centers
❏ 0491.027 Faucet holes on 4" (102mm) centers
• Extra right-hand hole
❏ 0491.035 Faucet holes on 4" (102mm) centers
• Extra left-hand hole
❏ 0490.156 Center hole only
610mm
(24)
102mm
(4)
203mm
(8)
OPTIONAL
Nominal Dimensions:
486mm (19-1/8") Round
83mm
(3-1/4)
184mm
(7-1/4)
FINISHED
WALL
OR
Bowl sizes:
SPLASH BACK
381mm (15") wide
308mm (12-1/8") front to back
146mm (5-3/4") deep
203mm
(8)
MIN.
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
C/L
851mm
(33-1/2)
Compliance Certifications -
Meets or Exceeds the
Following Specifications:
• ASME A112.19.2M for
Vitreous China Fixtures
686mm
(27)
MIN.
152mm
(6)
MAX.
486mm
(19-1/8)
COUNTERTOP (BY OTHERS)
SEALING
COMPOUND
11mm
(7/16)
BARRIER FREE
CLEARANCE
229mm
(9)
MIN.
*
273mm
(10-3/4)
187mm
(7-3/8)
318mm
(12-1/2)
*
178mm
(7)
203mm
(8)
SUPPLIES
AS REQ'D.
To Be Specified:
❏ Color: ❏ White ❏ Bone
❏ Linen ❏ Silver
❏ Fawn Beige ❏ Black
❏ Faucet*:
787mm (31)
851mm (33-1/2)
1-1/4 O.D.
WASTE
FINISHED
FLOOR
1-1/4 O.D.
TAILPIECE
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
SEE REVERSE FOR ADDITIONAL ROUGHING-IN
DIMENSIONS
NOTES:
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
* See faucet section for additional models available
*
SUGGESTED.
FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE
TEMPLATE SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 ACCESSIBLE AND USABLE
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Install lavatory 864mm (34") from finished floor.
Lavatory installed 51mm (2") minimum from front edge
of countertop provides 686mm (27") knee clearance area.
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
J45
© 2008 AS America Inc.
Revised 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|