RAVENNA™
PEDESTAL SINK
VITREOUS CHINA
RAVENNA™ PEDESTAL SINK
• Contemporary sleek design
• Made from vitreous china
• Rear overflow
• Faucet ledge with generous shelf area
• Supplied with mounting kit
• Optional integral mounted towel bar
(ordered separately, installed by customer)
• Shown with 2000.101 Ceramix single lever faucet
(not included)
❏ 0268.800 Faucet holes on 8" (203mm) centers
❏ 0268.400 Faucet holes on 4" (102mm) centers
❏ 0268.100 Center faucet hole only
Nominal Dimensions:
24-1/4" x 20" x 34"
(616 x 508 x 864mm)
20-1/4 (514mm)
4
3-1/4
(83mm)
FINISHED WALL
Separate Components:
(102mm)
❏ 0268.008 Pedestal top-8" (203mm) centers
❏ 0268.004 Pedestal top-4" (102mm) centers
❏ 0268.001 Pedestal top-Center hole only
❏ 0041.000 Pedestal only
8
PEDESTAL
TO WALL
(203mm)
5-1/4 (133mm)
PEDESTAL ANCHORING
SCREW HOLES 5/16 (8mm) DIA.
20
(508mm)
Bowl sizes:
19-3/8" (492mm) wide
11-7/8 (302mm) front to back
6" (152mm) deep
24-1/2
(622mm)
OPTIONAL
TOWEL BAR
9-3/8
(238mm)
REF.
Compliance Certifications -
DRAIN
CHASE
8
Meets or Exceeds the Following Specifications:
• ASME A112.19.2M for Vitreous China Fixtures
• CAN/CSA B45 Series
3/4" (19mm) DIA.
HOLES FOR
(203mm)
ANCHOR BOLTS
SUPPLIES
AS REQ'D
8 (203mm)
7
(178mm)
1-1/4 O.D.
WASTE
34
(864mm)
REF.
OPEN
TO
FLOOR
23
*
(584 mm)
20-1/2
*
1-1/4 O.D.
TAILPIECE
(521mm)
Recommended Component:
❏ Integral Towel Bar: 3520.000
FINISHED
FLOOR
(Specify 002 Chrome or 295 Satin Nickel)
PEDESTAL
SIDE SECTION
6-1/2 (165mm)
To Be Specified:
❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
NOTES:
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
*
SUGGESTED.
▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.
■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST
BE TAKEN FROM FIXTURE.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
* See faucet section for additional models available
IMPORTANT: Dimensions of fixtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided pages.
J13
© 2008 AS America Inc.
Revised 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|