2083 SERIES
BATHING POOL
STANDARD®
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
INSTALLATION INSTRUCTIONS
60"
(1524mm)
7-3/4"
(197mm)
70mm
(2-3/4)
3/4"
(19mm)
FINISHED
WALL
THANK YOU...
for selecting an American Standard bath. Your
new bath is shipped to you after careful
inspection. All you need to finish the installation
are your selected fittings.
4"
15-3/8"
(391mm)
(102mm)
229mm x 305mm
(9 x 12)
FLOOR
CUTOUT
4"
(102mm)
32"
(813mm)
To insure maximum performance and pleasure
from this product, please follow the instructions
and cautions.
+
2-3/8" 13mm
+
(2-3/8) (1/2)
25mm
(1)
4-1/2"
(114mm)
C/L OF 1/2
SUPPLIES
AS REQ'D
C/L OF
DRAIN
SHOWER ARM- 1/2 N.P.T.
1-1/4"(32mm) DIA. HOLE
List of Optional Components (not included):
• Standard Bath Caddie 9533.100*
C/L OF CURTAIN ROD
USUALLY 76"(1930mm) FROM
FINISHED FLOOR
* see your American Standard Distributor
FINISHED
WALL
4"
C/L OF
VALVES
(2) 2-1/8"(54mm)
DIA. HOLES
(102mm)
List of Required Components (not included):
• Standard Bath Drain 1501.170*
• Bath Filler*
OPTIONAL
TO FLOOR
USUALLY
BETWEEN
65 & 78
4"
4"
SPOUT-
1/2 N.P.T.
3-1/2"
(89mm)
(102mm)
(102mm)
16"
(406mm16)
(1651 & 1981mm)
1"
* see your American Standard Distributor
(25mm)
SEE
NOTE
19-3/4"
(502mm)
20"
(508mm)
TOP OF DECK
2"
(51mm)
ROUGH
FLOOR
4-5/8"
(117mm)
1-1/2 N.P.T. THREADS
1-1/2 O.D. TAILPIECE
List of Required Tools and Supplies:
BATH SUPPORT MATERIAL
Tools
Supplies
• Nails
• Putty
• Caulk
• Level
GENERAL SPECIFICATIONS FOR 2083 BATHING POOL
INSTALLED SIZE
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
60 x 32 x 20 In.
(1524 x 813 x 508mm)
100 Lbs. (45 Kg.)
(waterproof)
WEIGHT
• 1 x 3 or 2 x 4
Stringers
• Drop Cloth
• Mortar Mix
or Grout
551 Lbs. (250 Kg.)
WEIGHT w/WATER
54 Gal. (204 L)
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
18 x 42 In. (457 x 1067mm)
25 X 54 In. (635 x 1372mm)
14 In. (356mm)
Woodworking Tools
• Personal Safety
Equipment
41 Lbs./Sq.Ft. (202 Kgs./Sq.m)
• Caulking Gun
(PROJECTED AREA)
20.8
35.3
PTS.
3
CUBE (FT
)
GENERAL INSTALLATION INFORMATION
BATH MAY ONLY BE INSTALLED IN A RECESS TYPE INSTALLATION.
Locate studs as required. Insure rough dimensions are proper, plumb, and square. The following procedure must be used for all
installations: Leveling support stringer should be as indicated. This bath is not self-supporting and must be supported along it's entire
bottom. Support with mortar or grout.
Position bathtub within the recess, check level front to back and side to side, shim as necessary. To secure the tub to wood studs, use
drywall screws with flatwashers or roofing nails immediately above the flange of the bath. To secure the tub to steel studs, use 4" drywall
screws and flatwashers.
SEE PAGE 2 FOR COMPLETE INSTALLATION INFORMATION.
CAUTION: TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE BATH.
The tile or similar finished floor will be butted against the bottom of the tub apron, also holding the tub in place.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
© AS America, Inc. 2008
All product names listed herein are trademarks
of AS America, Inc. unless otherwise noted.
753450-100 REV. B
Download from Www.Somanuals.com. All Manuals Search And Download.
|