Color 150/RG™
General Information
Unpacking: Thank you for purchasing the Color 150/RG™ by Ameri-
can DJ®. Every Color 150/RG™ has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the ship-
ping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all accessories necessary to operate the unit have
arrived intact. In the event damage has been found or parts are miss-
ing, please contact our toll free customer support number for further
instructions. Please, do not return this unit to your dealer without first
contacting customer support.
American DJ
®
Introduction: The Color 150/RG™ is an intelligent fixture that can
run In DMX mode, as a stand alone sound active piece, or in a Master/
Slave configuration. The Color 150/RG™ comes with several build in
programs and is best used in multiples of four. This unit use a sepa-
rate color and gobo wheel. This piece is best used with a fog or haze
machine to enhance the beam output. The Color 150/RG™ comes
with two changeable gobos. This unit will take custom gobos (26mm
- 22mm viewable). An optional MINI/C blackout controller may be pur-
chased separately.
Customer Support: American DJ® provides a toll free customer sup-
port line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
5:00 p.m. Pacific Standard Time.
Voice:
Fax:
(800) 322-6337
(323) 582-2610
E-mail:
Warning! To prevent or reduce the risk of electrical shock or fire, do
User Instructions
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact
American DJ® customer support.
American DJ
4295 Charter Street
Los Angeles Ca. 90058
Please do not discard the shipping carton in the trash, recycle when
ever possible.
Revised 8/01
Download from Www.Somanuals.com. All Manuals Search And Download.
Color 150/RG™
REAR PANEL
Controls and Functions
Color 150/RG™
Controls and Functions
1. Dip Switches - These switches serve two functions. In master
slave mode these switches are used to assign a specific head
address. In DMX mode these switches are used to assign a DMX
address to the unit. In DMX mode each switch corresponds to a
specific value based on binary code. See page 7 for a detailed
explanation of DMX binary code.
2. Microphone - This microphone receives external low frequencies to
trigger the unit in Sound-Active and Master/Slave mode.
3. Audio Sensitivity Knob - This adjust audio sensitivity of the inter-
nal microphone (5). Turning the sensitivity knob in the clockwise
direction will increase the sensitivity to sound. Turning the knob in
the counter clockwise direction will decrease the fixture’s sensitivity
to sound.
4. Gobo Replacement Thumb Screw - See page 14 for Gobo replace-
ment.
5. Power Indicator - This LED will flash when it receives either an
audio or DMX signal.
6. MINI/C Controller Jack - This jack is for use with the optional
MINI/C Blackout controller only. Do not attempt to connect an audio
signal this jack, this will damage the PC board and void your manufac-
tures warranty!
1
2
3
4
5
6
7
8
9
10
11
12 13
14 15
BOTTOM PANEL
7. XLR Output Jack - This jack is used to transmit the incoming
DMX signal to another DMX fixture, or transmit a Master/Slave signal
to the nest Color 150/RG™ in the chain. For best results in DMX
or Master/Slave mode terminate this jack if it is the last unit in the
chain. See “Terminator” on page 7.
8. Power Cord - Connect only to a matching power outlet. Never use
this fixture is the ground prong has been removed or broken off.
9. Fuse Holder - This housing stores the 3 amp GMA protective
fuse. Always replace with the exact same type fuse, unless other
wise instructed, by an authorized American DJ® service technician.
10. XLR Input Jack - This jack is used to accept an incoming DMX
signal or Master/Slave signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
Color 150/RG™
Controls and Functions
Color 150/RG™
Operation
you to link up to 16 units together and operate without a controller. The
units will be sound activated. In Master-Slave operation one unit will act
as the controlling unit and the others will react to the controlling units
programs. Any unit can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units
together via the XLR connectors on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR is the
output. The first unit in the chain (master) will use the female XLR
connector only. For longer cable runs we suggest a terminator at
the last fixture. Refer to the set-up procedures beginning on page
10.
11. Cooling Fan - This fan is used to keep the unit operating at a cooler tem-
perature. Keep the fan grill clean. Never block the grill, improper cooling may
result in premature lamp failure.
12. Gobo Wheel - This wheel holds the two replaceable rotating gobos. The
gobos are 26mm (20mm viewable). For list of stock replaceable gobos contact
customer support or visit us on the web. Custom gobos may be order through
customer support. Please contact customer support for a quote on all custom
gobos.
13. Gobo Wheel Cover - This protective cover shields the gobo wheel. To
access and change the gobos remove this cover.
14. Gobo Wheel Cover Retaining Thumb Screw - This thumb screw retains
the gobo wheel cover. To access the gobo wheel remove this screw and the
gobo wheel cover.
2. Follow the Master-Slave dip-switch chart on page 16 for proper
dip-switch settings.
3. The optional MINI/C Blackout Controller may be used in this
operation mode to control the blackout.
4. After all the units settings have been set and are plugged in, adjust
the sensitivity knob on the rear of the master unit to make them
react to sound.
15. Fully Focusing Lens - This is high quality lens that is fully focusing. To
focus this lens, turn the lens in clockwise and counter-clockwise direction until
you achieve proper focus.
Color 150/RG™
Operation
5. Several unit may share the same slave setting as long as there
are no more than 16 units in a Master-Slave configuration, however
only one unit may have the “Master - Head 1” dip switch setting.
Note: Stand-Alone and Master-Slave operation require sound to acti-
vate! The units will blackout in this mode to conserve bulb life when
there is no sound present.
Linking: Your fixture comes with several built-in programs. These pro-
grams are designed to work with up to 16 units when daisy-chained
together in a master-slave configuration. Any unit can function as either
a “Master Unit” or a “Slave Unit.” Link the units together using standard
DMX cable.
Master/Slave Linking:
For a more dramatic effect, link several Color units together.
Stand-Alone Operation (Sound Active): This function allows a
single unit to run to the beat of the music. Only use this function when
running a single unit, or when running several units as individuals.
1. To activate the Sound-Active mode, set dip switch 10, on the
rear of unit to the ON position (See “Master Unit” on the DIP
SWITCH chart on page 15).
2. The unit will now react to the low frequencies of music via the inter-
nal microphone.
Optional MINI/C blackout controller
3. Adjust the audio sensitivity knob on the rear of the unit to make the
unit more or less sensitive to sound. Turning the sensitivity knob in
the clockwise direction will increase the sensitivity, turning the knob
in the counter-clockwise direction will decrease the fixture’s sensi-
tivity to sound.
4. The optional MINI/C Blackout Controller may be used with this
function. This controller is used for blackout function only.
To next Color 150/RG™ if applicable
Master-Slave Operation (Sound Active): This function will allow
Download from Www.Somanuals.com. All Manuals Search And Download.
Color 150/RG™
Operation
Color 150/RG™
Set Up
Universal DMX Control: This function allows you to use a universal
DMX 512 controller such as the American DJ® DMX Operator™ or
Show Designer™ to control lamp intensity, color, and gobo. Operating
through a DMX controller allows the freedom to create unique pro-
grams tailored to one’s individual needs.
Power Supply: Before plugging your unit in, be sure the source
voltage in your area matches the required voltage for your American
DJ® Color 150/RG.™ Because line voltage may vary from venue to
venue, you should be sure your unit voltage matches the wall outlet
voltage before attempting to operate you fixture.
1. The Color 150/RG™ uses three DMX channels. Channel one con-
trols the lamp intensity (dimmer), channel two controls the color
selection, and channel three control the gobo wheel. Please refer
to page 15 for a detailed description of the DMX traits.
2. To control your fixture in DMX mode, follow the unit set-up proce-
dures beginning on page 10 as well as the set-up specifications
that are included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create custom programs.
5. When using a DMX controller and setting up for DMX operation
follow the dip switch settings on page 15.
DMX-512: DMX is short for Digital Multiplex. This is a universal
protocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that
travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR
terminals located on all DMX fixtures (most controllers only have a
DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX
fixtures try to use the shortest cable path possible. The order in which
fixtures are connected in a DMX line does not influence the DMX
addressing. For example; a fixture assigned a DMX address of 1 may
be placed anywhere in a DMX line, at the beginning, at the end, or
anywhere in the middle. When a fixture is assigned a DMX address of
1, the DMX controller knows to send DATA assigned to address 1 to
that unit, no matter where it is located in the DMX chain.
6. For help operating in DMX operation consult the manual included
with your DMX controller.
7. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture in you DMX chain.
DMX Linking:
Dip-switches in DMX mode: This unit uses dip switches to assign a
DMX address. Each dip switch represents a binary value.
Dip Switch 1 address equals 1
DMX CHANNEL
Dip Switch 2 address equals 2
2
8
32 128 SP
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
To next DMX unit or terminate.
ON
1 2 3 4 5 6 7 8 9 10
1
4
16 65 256
Each dip switch has a preset value. A specific DMX address is set by
combining the dip switches that sum your desired value. For example:
Download from Www.Somanuals.com. All Manuals Search And Download.
Color 150/RG™
Set Up
Color 150/RG™
Set Up
To achieve a DMX address of 21, combine dip switches 1, 3, and 5.
Sense dip switch 1 has a value of 1, dip switch 3 has a value of 4,
and dip switch 5 has a value of 16, the combination of the create a
DMX value of 21.
COMMON
DMX +
1
2
1
2
DMX512 OUT
3-PIN XLR
DMX512 IN
3-PIN XLR
3
3
DMX -
Figure 7
Set DMX address 21:
Set DMX address 201:
Dip-switches # 1 = 1
Dip-switches # 1 = 1
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number ZDMX/T) will decrease the possibilities of erratic
behavior.
3 = 4
5 = 16
= 21
4 = 8
7 = 64
8 = 128
= 201
Data Cable Requirements (For DMX and Master/Slave Opera-
tion): The Color 150/RG™ can be controlled via DMX-512 protocol.
The DMX address is set using the dip-switches on the rear panel of the
Color 150/RG™. Your unit excepts 3-pin XLR connector for data input
and data output (Figure 5). When using a DMX controller with 5-Pin
XLR output jacks or when linking from a DMX fixture with 5-Pin XLR
jack to the Color 150/RG™, be sure to follow
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 8
the pin conversion chart on page 12. If you are
making your own cables, be sure to use standard
two conductor shielded cable (This cable may be
purchased at almost all pro sound and lighting
stores). Your cables should be made with a male
and female XLR connector on either end of the
cable. Also remember that DMX cable must be
daisy chained and can not be split.
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Figure 5
Notice: Be sure to follow figures 6 and 7 when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
Ground/Shield
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Pin 1
Pin 1
Pin 2
Pin 3
Data Compliment (- signal)
Data True (+ signal)
Not Used
Pin 2
Pin 3
XLR Female Socket
2 Cold
XLR Male Socket
1 Ground
XLR Pin Configuration
Pin 1 = Ground
2 Cold
1 Ground
Do Not Use
Do Not Use
Pin 2 = Data Compliment (negative)
Not Used
3 Hot
3 Hot
Pin 3 = Data True (positive)
Figure 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Color 150/RG™
Fuse & Lamp Replacement
Color 150/RG™
Halogen Lamp Warning
Caution: Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ® technician.
Replacing with anything other than the specified part can damage the
unit and will void the manufactures warranty.
Halogen Lamp Warning:
This fixture is fitted with a halogen lamp which
is highly susceptible to damage if improperly han-
dled. Never touch the lamp with your bare fingers
as the oil from your hands will shorten lamp life.
Also, never move the fixture until the lamp has
had ample time to cool. Remember, lamps are not
covered under warranty conditions.
Warning: If, after replacing the lamp or fuse either one continues
to blow, STOP using the unit. Contact customer support for further
instructions, you may have to return the unit for servicing. Continuing
to use the unit may cause serious damage.
Fuse Replacement: Disconnect the unit’s main power supply. Insert
a standard flat head screw driver in to the fuse holder housing. Turn
the screwdriver in counter-clockwise direction to remove the fuse
holder. Remove the fuse holder to expose the fuse. Remove the old
fuse and discard it. Replace the fuse with the same type. Insert the
fuse holder back into it’s housing and turn it in clockwise direction to
lock the holder in place.
Color 150/RG™
Gobo Replacement
This unit includes two interchangeable gobos. These gobo may
substituted with any 26mm gobo (20mm viewable). A detailed list of
available gobo for this unit may be found on the American DJ® web
site, if you do not have access to the internet please contact customer
support and request a catalog. To change the gobos;
1. Flip unit over so the bottom is facing up.
2. Remove the thumb screw on the rear panel of the unit and slide out
the protective fan grill plate.
3. Removing the fan grill plate will expose an addition thumb screw
that retains the gobo wheel protective cover. Remove this thumb
screw and cover.
Lamp Replacement: Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power and
allow the unit ample time to cool before attempting to replace the
lamp. Lamp replacement has been made simple by incorporating the
use of a flip-up top cover that is retained by a single thumb screw.
1. Be sure to follow the proper handling procedures that deal
with halogen lamps. Never touch the new lamp with your bare
fingers.
2. Remove the single thumb screw located on top of the unit. This
screw holds the flip-up lamp socket assembly cover in place.
3. Flip-up the cover. The cover is on hinges and will not fall off.
4. Carefully remove the old lamp and discard it in the trash.
5. Replace the lamp with an exact match and reassemble.
4. Once the gobo wheel is exposed, use a small flat head screw drive
to gently push one end of the gobo wheel down. This will expose
the opposite end of the gobo wheel, allowing you to remove a
gobo and replace it with another.
5. Use a small flat head
Fan Plate Pro-
tective Plate
screwdriver to remove the
gobo retaining ring, this
Unit Bottom
will allow you to pop out
Gobo Wheel
the gobo.
6. Insert a new gobo and
reassemble in reverse
Flip-Up Lamp Cover
Lamp/Socket Assembly
order.
Gobo Wheel
Cover
Thumb Screw Retaining Hole
Gobo Wheel Cover
Thumb Screw
Unit Top Cover
Download from Www.Somanuals.com. All Manuals Search And Download.
Color 150/RG™
Cleaning
Color 150/RG™
DMX Traits
Fixture Cleaning:
This chart below details the DMX traits of the fixture. The individual
trait can only be accessed an universal DMX controller. Note: The
Color 150/RG™ has a special DMX function
Due to fog residue, smoke, and dust cleaning the internal and external
optical lenses and mirror should be carried out periodically to optimize
light output. Cleaning frequency depends on the environment in which
the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club
use we recommend cleaning on a monthly basis. Periodic cleaning will
ensure longevity, and crisp output.
DMX CHANNEL
1
2
3
DIMMER
COLOR
GOBO
1. Use normal glass cleaner and a soft cloth to wipe down the outside
casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external lens with glass cleaner and a soft cloth every
20 days.
4. Clean the internal lens with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
CLR SCROLL FST
213-255
181-212
255
100%
50%
CLR SCROLL MED
CLR SCROLL SLW
PURPLE
255
128
255
170-180
149-169
ROTATING GOBO 2
PINK
128-148
107-127
171
170
128
ORANGE
S P O T
86
85
YELLOW
86-106
Color 150/RG™
Trouble Shooting:
Listed below are a few common problems that you may encounter,
with solutions.
Trouble Shooting
GREEN
BLUE
65-85
44-64
ROTATING GOBO 1
00
0
RED
23-43
01-22
No light output from the unit;
1. Be sure you have connected your unit into a standard 120V wall
WHITE
0
0%
outlet.
Color 150/RG™
Master/Slave Settings
2. Be sure the external fuse has not blown. The fuse is located on the
rear panel of the unit.
3. Remove the lamp cover and be sure the lamp is seated in its
socket properly. Occasionally lamps become loose during shipping
be sure the lamp is push in to its socket all the way.
4. Be sure the fuse holder is completely and properly seated.
This chart details the Master/Slave dip switch setting for Master/Slave
configuration for four units. Use these dip switch setting when you will
be using two or more fixtures in a Master/Slave configuration. The
“Master - Head 1” settings should only be used once.
ON
ON
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may not
activate the unit.
1 2 3 4 5 6 7 8 9 10
Master - Head 1
1 2 3 4 5 6 7 8 9 10
Head 2
ON
ON
2. Be sure the SENSITIVITY KNOB (3) is not set to the maximum
position.
3. Be sure the dip-switches are set for Stand-Alone mode.
1 2 3 4 5 6 7 8 9 10
Head 3
1 2 3 4 5 6 7 8 9 10
Head 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Color 150/RG™
Set Up
Color 150/RG™
DMX Dip Switch Chart
Special function dip-switch settings: The following dip-switch set-
tings detail several special functions. These function included locking
the unit on one color, locking the unit on a single gobo, or scrolling
through colors.
This chart list the DMX dip switch setting for DMX address 1 through
511. Follow the instructions below to configure fixture dip switches with
your desired DMX address.
DMX Address Quick Reference Chart
ON
ON
DIP SWITCHES
1 2 3 4 5 6 7 8 9 10
Locked on Gobo 1
1 2 3 4 5 6 7 8 9 10
Locked on Gobo 2
Dip Switch Position
#9
#8
#7
#6
X
X
X
X
X
X
X
O
X
X
O
X
X
X
X
O
X
X
X
O
X
X
O
O
X
X
O
O
O
O
X
X
X
O
X
X
O
O
X
O
X
O
X
O
O
X
X
O
O
X
O
O
O
X
O
O
O
O
Switches 3-9 only apply to
color options
Switches 3-9 only apply to
color options
DMX DIP Switch Settings
X = OFF
O =ON
O
O
O
O
O
O
ON
ON
#1 #2 #3 #4 #5
X
O
X
O
X
O
X
X
X
O
O
X
X
O
X
X
X
X
O
O
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
3
64 96 128 160 192 224 256 288 320 352 384 416 448 480
1
2
3
4
5
6
33 65 97 129 161 193 225 257 289 321 353 385 417 449 481
34 66 98 130 162 194 226 258 290 322 354 386 418 450 482
35 67 99 131 163 195 227 259 291 323 355 387 419 451 483
36 68 100 132 164 196 228 260 292 324 356 388 420 452 484
37 69 101 133 165 197 229 261 293 325 357 389 421 453 485
38 70 102 134 166 198 230 262 294 326 358 390 422 454 486
1 2 3 4 5 6 7 8 9 10
Locked on White
Switches 1 & 2 only apply
to gobo options
1 2 3 4 5 6 7 8 9 10
Locked on Yellow
Switches 1 & 2 only apply
to gobo options
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
O
X
X
X
X
O
O
O
O
X
X
X
X
O
O
O
O
X
X
X
X
O
O
O
O
X
X
7
8
9
39 71 103 135 167 199 231 263 295 327 359 391 423 455 487
40 72 104 136 168 200 232 264 296 328 360 392 424 456 488
41 73 105 137 169 201 233 265 297 329 361 393 425 457 489
ON
ON
ON
ON
O
O
O
O
O
O
O
O
X
X
X
X
10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490
11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491
12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492
13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493
14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494
15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495
16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496
17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497
18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498
19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499
20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500
21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501
22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502
23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503
24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504
25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505
26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506
27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507
28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508
29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509
30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510
31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511
X
1 2 3 4 5 6 7 8 9 10
Locked on Red
Switches 1 & 2 only apply
to gobo options
1 2 3 4 5 6 7 8 9 10
Locked on Orange
Switches 1 & 2 only apply
to gobo options
X
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
X
X
1 2 3 4 5 6 7 8 9 10
Locked on Blue
Switches 1 & 2 only apply
to gobo options
1 2 3 4 5 6 7 8 9 10
Locked on Pink
Switches 1 & 2 only apply
to gobo options
X
X
X
O
O
O
O
O
O
O
O
ON
ON
ON
ON
1 2 3 4 5 6 7 8 9 10
Locked on Green
Switches 1 & 2 only apply
to gobo options
1 2 3 4 5 6 7 8 9 10
Locked on Purple
Switches 1 & 2 only apply
to gobo options
DMX Address
The center numbers of this chart (1-511) represent a DMX address. The "X"'s
and "O"'s along the top and side of the chart represent dip switch poistion ("X"
for off and "O" for on). Find your desired DMX address from the center chart.
Identify the position for dip switches 1-5 from the chart on the left and dip
switches 6-9 from the chart on the top. Adjust the dip switches on your fixture to
match the position settings of the chart. For fixtures with 10 dip switches; dip
switch 10 is reserved for special functions.
1 2 3 4 5 6 7 8 9 10
Rotating Color Sequence 1
Switches 1 & 2 only apply
to gobo options
1 2 3 4 5 6 7 8 9 10
Rotating Color Sequence 2
Switches 1 & 2 only apply
to gobo options
Download from Www.Somanuals.com. All Manuals Search And Download.
Color 150/RG™
Warranty
Technical Specifications:
Model: Color 150/RG™
1-YEAR LIMITED WARRANTY
A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be
free of manufacturing defects in material and workmanship for a period of 1 Year (365 days)
from the date of purchase. This warranty shall be valid only if the product is purchased
within the United States of America, including possessions and territories. It is the owner’s
responsibility to establish the date and place of purchase by acceptable evidence, at the
time service is sought.
Lamps:
ZB-JCR H5 15v/150w
Voltage:
120v/60Hz
Dimensions:
14.25”(H) x 6.75”(W) x 9.75”(D)
with yoke extended
7 colors gobo, plus white spots
2 interchangeable, plus spot
12 Lbs.
Colors
Gobos:
Weight:
B. For warranty service, send the product only to the American DJ® factory. All shipping
charges must be pre-paid. If the requested repairs or service (including parts replacement)
are within the terms of this warranty, American DJ® will pay return shipping charges only
to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package. No accessories should be shipped with the product. If any
accessories are shipped with the product, American DJ® shall have no liability whatsoever
for loss of or damage to any such accessories, nor for the safe return thereof.
Fuse:
3 Amp GMA
Duty Cycle:
DMX:
15 min on/off
3 Channels
Sound Active:
Working Position:
Warranty:
Yes, Master/Slave mode
Any Safe, Secure Position
1 Year (365 days)
C. This warranty is void if the serial number has been altered or removed; if the product
is modified in any manner which American DJ® concludes, after inspection, affects the reli-
ability of the product; if the product has been repaired or serviced by anyone other than the
American DJ® factory unless prior written authorization was issued to purchaser by Ameri-
can DJ®; if the product is damaged because not properly maintained as set forth in the
instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ® will replace defec-
tive parts at its expense, and will absorb all expenses for warranty service and repair labor
by reason of defects in material or workmanship. The sole responsibility of American DJ®
under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of American DJ®. All products covered by this warranty
were manufactured after January 1, 1990, and bear identifying marks to that effect.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
E. American DJ® reserves the right to make changes in design and/or improvements upon
its products without any obligation to include these changes in any products theretofore
manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any acces-
sory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ® in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set
forth above. And no warranties, whether expressed or implied, including warranties of mer-
chantability or fitness, shall apply to this product after said period has expired. The con-
sumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly
provided above; and under no circumstances shall American DJ® be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
©American DJ Supply
American DJ Supply Group of Companies World Headquarters:
4295 Charter Street Los Angeles, CA 90058 USA
G. This warranty is the only written warranty applicable to American DJ® Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions
heretofore published.
H. Lamps are not covered under this or any other warranty, either written or implied.
Tel: 323-582-2650 Fax: 323-582-2610
Download from Www.Somanuals.com. All Manuals Search And Download.
|