OneYear LimitedWarranty
Amcor, Inc. (“Amcor”) warrants the original retail purchaser (“Purchaser”) purchasing in the
United States that the Amcor product with which this warranty is enclosed is free from defects
in materials and workmanship.
Amcor’s sole obligation under this warranty is to replace, or at Amcor’s discretion, to repair,
free of charge, all defective parts, for a period of one (1) year from date of original purchase.
ANY IMPLIEDWARRANTY OF MERCHANTABILITY IS SIMILARLY LIMITEDTO ONE (1)
YEAR FROM DATE OF ORIGINAL PURCHASE AND NO ACTION BASED UPON ANY
IMPLIEDWARRANTY OF MERCHANTABILITY OR OTHERWISE MAY BE COMMENCED
AFTER EXPIRATION OF ONE (1)YEAR FROM DATE OF ORIGINAL RETAIL PURCHASE.
Some states do not allow limitations on how long an implied warranty lasts,so the above limitation
may not apply to you.
P O R T A B L E
Owner’s Manual
The provisions of this warranty shall not apply to any product which in Amcor’s judgment has
been (1) subject to misuse or neglect. (2) damaged in an accident. (3) used for a purpose for
which it was not designed, or (4) repaired or altered in any way that adversely affected its
performance or reliability.
For models ALD-12,000E and ALD-12,000EH
To obtain warranty service, the defective product or part must be shipped or delivered to:
Amcor’s authorized service center. All postage,insurance and shipping charges are the responsibility
of the Purchaser and are not included in this warranty.
AMCOR NEITHER ASSUMES NOR AUTHORIZES ANY PERSONTO ASSUME FOR IT ANY
OTHER ( LIABILITY IN CONNECTIONWITH ITS PRODUCTS,THEREARE NOWARRANTIES
WHICH EXTEND BEYONDTHE DESCRIPTION ONTHE FACE HEREOF. NO RESPONSIBILITY
ISASSUMED FOR INCIDENTAL OR CONSEQUENTIAL DAMAGESTHAT MAY RESULT FROM
THE USE OFANAMCOR PRODUCT,NOR FORTHE DAMAGES DUETOACCIDENT, ABUSE,
LACK OF RESPONSIBLE CARE,THE AFFIXING OF ANY UNAUTHORIZED ATTACHMENT,
LOSS OF PARTS, OR USEATAVOLTAGE OTHERTHAN SPECIFIED. Some states do not allow
the exclusion of limitation of incidental or consequential damages, so these limitations may not
apply to you.
Amcor disclaims all liabilities for defects or damages caused by use of replacement parts obtained
from or by service at any service center other than Amcor’s authorized service center.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
Product: AMCOR Portable Air Conditioner
Model: ALD-12,000E/EH
Date Purchased:_____________________________________ Production Code:________
It is important that you read
these instructions before
using your new purchase and
we strongly recommend that
you keep them in a safe place
for future reference.
Dear Customer: Please keep this warranty for your record. DO NOT return it.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Drainage
Specifications
During the process of cooling, some water will be extracted from the air into the unit. Most of this water
is used to cool the unit and make it run more efficiently. This is a feature not found in most Portable Air
Conditioners. If the unit is operated inVERY HUMID air, water will collect in the container inside the unit.
If the InternalWater Container is full, the backlight on the LCD display will flash, the unit will shut off, and
it must be drained before it will re-start.
Model Number
Cooling Capacity
Heating Capacity
Power Consumption
Humidity Removal Capacity
Recommended room size*
Power Supply
ALD-12,000E
12,000 BTU/hr
N/A
ALD-12,000EH
12,000 BTU/hr
12,000 BTU/hr
950W / 8.4A
65 Pts. / Day
Up to 400 sq. ft.
115V / 60Hz / 1 Phase
Rotary
How to Drain the Unit
Use a Shallow Container or Dish
950W / 8.4A
65 Pts. / Day
Up to 400 sq. ft.
115V / 60Hz / 1 Phase
Rotary
1. Turn off the unit.
2. Position a flat container or dish under the drain hole.
Do not allow the water to drip continuously into
the container, as it might easily overflow.
3. Remove the drain knob & rubber plug from
the drain hole.
Compressor
The condensed water will drain out automatically.
Refrigerant
R-22
R-22
4. When the container is almost full, replace the
rubber plug into the drain hole to stop the water.
Empty the container.
Fan Speed
2
2
Timer
1-12 hours
1-12 hours
5. Repeat steps 2, 3 & 4 until all the condensed water
is emptied.
Temperature Set Range
UnitWeight
62 F - 90 F
65 lbs.
62 F - 90 F
68 lbs.
6. Once all the condensed water has been removed,
replace the rubber plug into the drain hole firmly.
The FullWater indicator should be off now.
Dimensions
16"W x 17"D x 30"H
Cooling: 62 F to 110 F
16"W x 17"D x 30"H
7. Replace the drain knob.
WorkingTemperature
Cooling: 62 F to 110 F
Heating: 41 F to 81 F
8. Turn unit on, the unit will resume working.
REMARKS:
The cooling capacity of the unit may be affected by the height of the ceiling,
quality of insulation, number of windows, etc.
10
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Parts
Cool
SetTemp. Low Fan Timer
Front
Back
Control Panel
Room
Temp.
High
Fan
Not available
on all units
Fan Only
Auto
Power
Mode:
AC or Fan
3
Temp. Up
Timer
On / Off
Temp. Down
Fan Speed:
High / Low
Not available on all units
Setting Mode/Function
1. Control Panel
2. Cooling Air Outlet
3. Handle
5. Air Filter
6. Air Inlet
Press the MODE button to select the required working mode:Automatic, Cooling, Fan or Heating (Heating is only
available for ALD-12,000EH).The green indicator illustrating your selected mode lights up. It is recommended to
select Cooling or Heating mode and set your desired temperature,as theAuto mode has a preset temperature (please
see below) that cannot be changed.
7. Exhaust Air Outlet
The indicators of the functions in progress come on at the same time,e.g.Cool and Lo = Cooling mode with Low fan speed.
4. Castors
8. Cord Hanger
9. Water Stopper (Rubber Plug Inside)
Auto Mode
When this mode is selected,the unit is preset to the following temperature settings and unit will only start to:
• Cool when room temperature is higher than 75ºF
• Heat when room temperature is lower than 68ºF (ALD-12,000EH only)
If room temperature is between 68ºF and 75ºF, unit will stay in Fan mode. Again, when inAuto Mode, the temperature
settings cannot be changed.
Setting theTemperature in Cooling or Heating Mode
The display window’s default is to display the ambient room temperature. The green indicator light under RT is on.
(RT = RoomTemperature)
Accessories
10. Adaptor - for insertion over the
hose and into the back of the
air conditioner
10
12
To set your desired temperature, press theTemperature up or down buttons (ranging from 62ºF to 90ºF). Each press
will increase or decrease your set temperature by 1ºF. When pressing the temperature up or down buttons, the
window will change to display your set temperature.At this time, the green indicator will light under ST (Set
Temperature). Once the temperature up or down buttons is released, the window will return to displaying the
ambient temperature after a second.
Note: When unit is in the following modes: Auto, Cool, or Heat - the compressor will cool/heat the room to reach
the set temperature. Once the ambient temperature has reached the set temperature, the compressor will stop and
unit will run in Fan mode. To conserve energy, the compressor will not start immediately after a couple degrees
increase or decrease, but will wait for a 5ºF allowance. For example:
11. Exhaust Hose
11
12. Adjustable Slide Bar
13. Round Connector
14. Cap for Round Connector
13
In Cooling Mode with a set temperature of 70F
When compressor first stops after reaching 70ºF, unit will auto-switch to Fan.
Compressor will start cooling again when ambient temperature increases to 75ºF or above.
15. Remote Control
14
(Electronic control models only)
In Heating Mode with a set temperature of 72F
When compressor first stops after reaching 72ºF, unit will auto-switch to Fan.
Compressor will start heating again when ambient temperature drops to 67ºF or below.
15
In Auto Mode (with preset temperature of 68F for heat and 75F for cool)
Compressor will start cooling again when ambient temperature reaches above 80ºF or will start heating when
ambient temperature drops below 63ºF.
8
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
Mounting the Exhaust Pipe
Slide Bar
• The supplied Exhaust Hose can be
extended from 1 foot to 5 feet
Connector
for mounting. It is recommended that
you use the shortest possible length of Hose.
• Take care to prevent any kink or
bend in the middle of the Exhaust
Hose, as this will trap hot exhaust air,
which will radiate back into the room.
In order for this unit to function
properly,it must be vented to the
outside.
2. Attach Slide Bar Connector,
(Round Connector) to the
other end of the Hose by
extending hose at least 6".
Then tighten Hose by turning
the (Round Connector)
clockwise.
3. Place Adjustable Slide Bar in
the window and expand so it
fits tightly.
Fitting the Exhaust Hose through
the window is easy. Please see
below.
4. Lower the window.
5. Make sure the Hose has
no kinks.
1. Extend Hose at least 6" and
insert it into back of the unit,
tightening into place by turning
it clockwise.
Slide Bar has 3 sections which
allows installation in windows up
to 48" in width.
WARNING!
The length of the Exhaust Pipe is specially
designed according to the specification of
this product.
Round
Connector
Do not replace or extend it with your own hose
as this could cause the unit to malfunction.
Cleaning the Filter
Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt from the filters
and then rinse them thoroughly under running water (no hotter than 104ºF)
Dry thoroughly before replacing.
Wall Connection
1. Make a hole (5.1" in diameter)
in the wall.
3. Extend one end of the Exhaust
Pipe (part #11) and screw into
the Round Connector by
turning clockwise.
5. Push Adaptor to fit firmly
over the opening on the back
of the unit.
Notice! Never operate the unit without the filters.
2. Insert the Round Connector
(part #13) into the hole and
hold in place by using 4 small
screws (not supplied).
**When not in use, cover the
Round Connector and hole
with Cap (part #14).
4. Extend other end of exhaust
pipe and screw inAdaptor (part
#10) by turning clockwise.
7
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Use
Operation
Setting The Fan Speed
Press the SPEED button to choose the fan speed you require, high or low.
Important!
The indicator of high or low fan will light up at the same time.
• Leave the unit in an upright position for at least 2 hours before use.
• Always place the unit on an even surface.
If the unit is in AUTO mode, it will select the fan speed automatically according to the
ambient temperature (the related indicators, cool, fan or heat will light up), at this time the
fan speed switch is invalid.
• The power cord has a built-in L.C.D.I. (Leakage, Current, Detection, Interruption) circuit
breaker for added safety. If the power supply is interrupted, please press the reset
button to reconnect the unit to the power source. The green light should be on.
Setting theTimer
Press theTIMER button to set the operating hours you desire (1 to 12 hours, the timer
indicator will light up). When the set time has elapsed, the machine will turn off
automatically. The display window will show the hour(s) you set as you press theTIMER button.
If the timer button is not pressed, the unit will work continuously.
• Make sure the unit is connected to a correctly grounded power supply.
For proper operation, the unit must be vented to the outside.
• Do not cover or obstruct the appliance inlet or outlet grilles.
By pressing the timer button but without turning on the unit, you can PRE-SET the time for
the machine to work. For example, if you press the timer to ‘2’,
the unit will come on automatically after 2 hours.
• To avoid the risk of shock, the product should never be used in bathrooms, shower rooms
or in any other steamy or wet areas.
All the above functions can also be performed with the supplied remote
control. This remote control requires 2 AAA batteries to operate.
• Always transport the unit in an upright position.
• Do not sit or stand on the unit.
Regulating the Airflow Direction
• Do not place objects on the unit.
• Do not touch the unit with wet/damp hands or when standing barefoot.
Drainage of the water container is required before moving the unit or
putting it into storage.
• If the electric socket is different from the plug provided, have a professionally qualified
electrician replace the outlet with a suitable one. Avoid the use of adaptor plugs, multiple
sockets and/or extension cords; if their use is necessary, ensure that they conform to the
current safety regulations.
Move the air vent directly to adjust the
airflow direction from the horizontal louvres.
Turn the roller on the air vent to control
the airflow direction from the vertical louvres.
IMPORTANT!
The compressor will start approximately 3 minutes after the unit is turned on (this will
help prolong the life of the compressor). After switching the unit off, please wait at least
3 minutes before turning the unit back on.
• Do not pull the power cord or place it near a source of heat; always unroll it completely
to avoid the possibility of dangerous overheating.
• The cooling system will switch off if the room temperature is lower than set. The fan, however, keeps
working at the set level. If the ambient temperature rises above the chosen temperature +/ 5 F,
• If the power cord is damaged, it must be replaced by a qualified person.
the cooling will resume.
• In heating mode, the compressor will switch off if the room temperature is HIGHER than the one set
(the fan keeps working at the set level). When the room temperature drops 5 F below the chosen
temperature, heating will resume.
THE MANUFACTURER DISCLAIMS ANY RESPONSIBILITY IFTHE ABOVE
INSTRUCTIONS ARE NOT FOLLOWED.
• This machine is equipped with an ANTI-FROST function. Sometimes, while using the heating function
during low temperatures, the heating will stop for a while to melt the internal frost. When this occurs,
wait for heating to resume.
• As you switch on the heating, the fan will stop for 15-20 seconds prior to the unit starting.
4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Thank You!
Always unplug the unit from the wall outlet before beginning
the cleaning.
Thank you for choosing the portable air conditioner from AMCOR, a leading brand in
indoor air treatment. We would like you to enjoy the many benefits this unit offers, so
please read this manual carefully and take full advantage of the many advanced features
that your AMCOR Air Conditioner offers you.
Cleaning the Housing
Use a soft, damp cloth to wipe the body clean.
Never use strong chemicals, oil-based products, detergents, chemically treated cloths or other
cleaning solutions.These could possibly damage the cabinet.
AMCOR has specialized in complete indoor environment control, manufacturing
world-class air conditioners, dehumidifiers and air purifiers with innovative technology.
Cleaning the Filter
Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt from the filters and then
rinse them thoroughly under running water (no hotter than 104 F).
Dry thoroughly before replacing.
In designing these advanced products, we have listened carefully to our customers and have
passed their views on to our research and development laboratories.
We wish you many years of enjoyable use.
After reading this manual, please keep it in a safe place for future reference.
Do not wet the activated carbon filter, remove from frame before rinsing.
IMPORTANT! Never operate the unit without the filters.
Energy SavingTips
• Do not locate the air conditioner where furniture or other objects can obstruct
the airflow.
End of Season Storage
Unplug the unit.
• Keep doors closed so cool air does not escape.
• Keep the filters clean.
Drain the condensed water COMPLETELY (please refer to page 10).
Clean or change the filter.
Set the unit to maximum cooling and high speed fan initially, then adjust the unit
to a comfortable setting.
On a warm day, turn the unit to fan mode for a couple of hours so that the
inside can dry out completely.
It is recommended that the unit be put back into its original carton for storage.
Do not stack heavy objects on top of the unit.
NOTE: Use theTemperature Control (UP/DOWN) to adjust
Air Conditioner cooling to a desired level.
StoringThe Power Cord
When the unit is not in use, please store the power cord away as shown in Figure 3.
Fig. 3
2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|