ELECTRONIC
GAS DRYER
Use & Care Guide
For questions about features, operation/performance,
parts, accessories or service, call: 1-800-688-9900
or visit our website at...
Table of Contents................................................. 2
W10216187A
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
•
•
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
– Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
In the State of Massachusetts, the following installation instructions apply:
■
Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
■
■
If using a ball valve, it shall be a T-handle type.
A flexible gas connector, when used, must not exceed 3 feet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
■
■
Read all instructions before using the dryer.
■
Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch fire.
■
Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
■
■
Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
■
■
Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
■
■
Clean lint screen before or after each load.
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
■
■
The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
■
■
Do not reach into the dryer if the drum is moving.
Do not install or store the dryer where it will be exposed
to the weather.
See installation instructions for grounding requirements.
■
Do not tamper with controls.
SAVE THESE INSTRUCTIONS
IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.
INSTALLATION INSTRUCTIONS
Parts needed
Check local codes and with gas supplier. Check existing gas
Tools and Parts
supply, electrical supply, and venting. Read “Electrical
Gather the required tools and parts before starting installation.
Requirements,” “Gas Supply Requirements,” and “Venting
Read and follow the instructions provided with any tools listed
Requirements” before purchasing parts.
here.
■
For close-clearance installations between 31.5" (800.1 mm)
and 37" (939.8 mm), see “Plan Vent System” section for
venting requirements.
■
■
8" or 10" pipe wrench
■
■
■
■
Level
8" or 10" adjustable wrench
(for gas connections)
Vent clamps
Knife
■
■
Flat-blade screwdriver
Pipe-joint compound
resistant to LP gas
Adjustable wrench that
opens to 1" (25.4 mm) or
hex-head socket wrench
(for adjusting dryer feet)
■
Caulking gun and
compound (for installing
new exhaust vent)
37"
(939.8 mm)
■
¼" nut driver or socket
wrench
■
■
Pliers
Tape measure
Mobile home installations require metal exhaust system hardware
available for purchase from the dealer from whom you purchased
your dryer. For further information, please refer to the “Assistance
or Service” section.
Parts supplied
Remove parts package from dryer drum. Check that all parts are
included.
■
Mobile Home Installation Kit. Ask for Part Number 346764.
Metal exhaust system hardware.
■
4 Leveling legs
NOTE: Do not use leveling legs if installing the dryer on a
pedestal.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
■
For a garage installation, you will need to place the dryer
at least 18" (460 mm) above the floor. If using a pedestal, you
will need 18" (460 mm) to the bottom of the dryer.
Optional Pedestal
Are you placing the dryer on a pedestal? You have the option of
purchasing pedestals of different heights separately for this dryer.
You may select a 10" (254 mm) pedestal or a 15.5" (394 mm)
pedestal with a storage drawer. The pedestal will add to the total
height of the dryer for a total height of approximately
Do not operate your dryer at temperatures below 45ºF (7ºC).
At lower temperatures, the dryer might not shut off at the end of
an automatic cycle. Drying times can be extended.
The dryer must not be installed or stored in an area where it will
be exposed to water and/or weather.
46" (1168 mm) or 51.5" (1308 mm), respectively.
For a garage installation, you will need to place the 10" (254 mm)
pedestal at least 9" (229 mm) above the floor. You will need to
place the 15.5" (394 mm) pedestal at least 3" (76 mm) above the
floor.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
Installation clearances
The location must be large enough to allow the dryer door to
open fully.
Dryer Dimensions
50½"
(1282.7 mm)
Optional pedestal (15.5" [394 mm] model shown)
To order, call the dealer from whom you purchased your dryer or
refer to the “Assistance or Service” section.
38"
(965.2 mm)
Pedestal Height
10" (254 mm)
Color
Part Number
WHP1000SQ
XHP1550VW
XHP1550VM
White
15.5" (394 mm)
15.5" (394 mm)
White
Burgundy
*31½"
(800.1 mm)
27"
(686 mm)
Location Requirements
*Most installations require a minimum 5" (127 mm) clearance
behind the dryer for the exhaust vent with elbow. See “Venting
Requirements.”
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this
dryer. This dryer has been tested for spacing of 0" (0 mm)
clearance on the sides and rear. Recommended spacing should
be considered for the following reasons:
■
■
■
■
Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door, and
floor moldings.
Additional spacing should be considered on all sides of the
dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
You will need
■
A location that allows for proper exhaust installation. A gas
dryer must be exhausted to the outdoors. See “Venting
Requirements.”
■
Companion appliance spacing should also be considered.
Custom undercounter installation - Dryer only
0"
■
■
A grounded electrical outlet located within 2 ft (610 mm) of
either side of the dryer. See “Electrical Requirements.”
(0 mm)
A sturdy floor to support the total dryer weight of 200 lbs
(90.7 kg). The combined weight of a companion appliance
should also be considered.
38" min.
(965.2 mm)
■
A level floor with a maximum slope of 1" (25 mm) under entire
dryer. (If slope is greater than 1" [25 mm], install Extended
Dryer Feet Kit, Part No. 279810.) Clothes may not tumble
properly and automatic sensor cycles may not operate
correctly if dryer is not level.
1"*
(25 mm)
1"*
(25 mm)
27"
(686 mm)
*Required spacing
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Closet installation - Dryer only
Recommended installation spacing for recessed or
closet installation, with stacked washer and dryer
3"*
(76 mm)
14" max.*
(356 mm)
48 in.2*
The dimensions shown are for the recommended spacing.
(3100 mm2)
48 in.2
*
18" min.*
(31000 mm2)
(457.2 mm)
3"* (76 mm)
24 in.2*
(1550 mm2)
3"*
(76 mm)
1"*
31½"
5"**
(25 mm)
(800 mm) (127 mm)
A
B
A. Side view - closet or confined area
B. Closet door with vents
3"* (76 mm)
24 in.2
*
1"* (25 mm)
(15500 mm2)
*Required spacing
**For side or bottom venting, 0" (0 mm) spacing is allowed.
*Required spacing
Recessed or closet installation - Dryer on pedestal
6"* (152 mm)
14" max.*
(356 mm)
18" min.*
(457.2 mm)
76"
(1930 mm)
1"
(25 mm)
27"
(686 mm)
1"
1"*
31½"
**
5"
5½"**
(140 mm)
27"
(686 mm)
1"
(25 mm)
1"
(25 mm)
(25 mm) (25 mm) (800 mm)
(127 mm)
A
B
*Required spacing
A. Recessed area
**For side or bottom venting, 0" (0 mm) spacing is allowed.
B. Side view - closet or confined area
*Required spacing
Mobile home - additional installation requirements
This dryer is suitable for mobile home installations.
**For side or bottom venting, 0" (0 mm) spacing is allowed.
The installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280).
Installation spacing for cabinet installation
■
For cabinet installation, with a door, minimum ventilation
openings in the top of the cabinet are required.
Mobile home installations require:
7"* (178 mm)
7"* (178 mm)
■
■
■
Metal exhaust system hardware, which is available for
purchase from your dealer.
Mobile Home Installation Kit Part Number 346764. See “Tools
and Parts” section for information on ordering.
Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
9"*
(229 mm)
1"*
(25 mm)
5"**
31½"
27"
1"
1"
(127 mm) (800 mm)
(25 mm)(686 mm) (25 mm)
*Required spacing
**For side or bottom venting, 0" (0 mm) spacing is allowed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Requirements
Gas Supply Requirements
WARNING
WARNING
Electrical Shock Hazard
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Securely tighten all gas connections.
Do not use an extension cord.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (330 mm) water
column.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
■
120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is also recommended that a separate circuit
serving only this dryer be provided.
Failure to do so can result in death, explosion, or fire.
GROUNDING INSTRUCTIONS
Gas Type
■
For a grounded, cord-connected dryer:
Natural gas:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an
This dryer is equipped for use with Natural gas. It is design-
certified by CSA International for LP (propane or butane) gases
with appropriate conversion.
equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances.
■
Your dryer must have the correct burner for the type of gas in
your home. Burner information is located on the rating plate
in the door well of your dryer. If this information does not
agree with the type of gas available, contact your dealer or
call the phone numbers referenced in the “Assistance or
Service” section.
WARNING: Improper connection of the
equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service
representative or personnel if you are in doubt as to
whether the dryer is properly grounded. Do not modify the
plug provided with the dryer: if it will not fit the outlet, have
a proper outlet installed by a qualified electrician.
LP gas conversion:
Conversion must be made by a qualified technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting your gas company.
SAVE THESE INSTRUCTIONS
Gas supply line
■
Must include 1/8" NPT minimum plugged tapping accessible
for test gauge connection, immediately upstream of the gas
connection to the dryer (see illustration).
■
■
½" IPS pipe is recommended.
3/8" approved aluminum or copper tubing is acceptable for
lengths under 20 ft (6.1 m) if local codes and gas supplier
permit.
■
■
If you are using Natural gas, do not use copper tubing.
Lengths over 20 ft (6.1 m) should use larger tubing and a
different size adapter fitting.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
■
■
If your dryer has been converted to use LP gas, 3/8" LP
compatible copper tubing can be used. If the total length of
the supply line is more than 20 ft (6.1 m), use larger pipe.
Dryer gas pipe
■
The gas pipe that comes out through the rear of your dryer
has a 3/8" male pipe thread.
NOTE: Pipe-joint compounds that resist the action of LP gas
must be used. Do not use TEFLON®† tape.
Must include a shutoff valve:
B
*6¼"
(159 mm)
An individual shutoff valve must be installed within
6 feet (1.8 m) of the dryer in accordance with the National
Fuel Gas Code, ANSI Z223.1. The location should be easy to
reach for opening and closing.
C
E
A
1½"
(38 mm)
A
A. ½" NPT gas supply line
D
B
B. 3/8" NPT dryer pipe
A. 3/8" flexible gas connector
B. 3/8" pipe to flare adapter fitting
C. 1/8" NPT minimum plugged tapping
D. 1/2" NPT gas supply line
■
*NOTE: If the dryer is mounted on a pedestal, the gas pipe
height must be an additional 10" (254 mm) or 15.5" (394 mm)
from the floor, depending on the pedestal model. For a
garage installation, the gas pipe height must be an additional
18" (460 mm) from the floor.
E. Gas shutoff valve
Gas supply connection requirements
Venting Requirements
■
Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting
between the flexible gas connector and the dryer gas pipe, as
needed to avoid kinking.
WARNING
■
■
Use only pipe-joint compound. Do not use TEFLON®† tape.
This dryer must be connected to the gas supply line with a
listed flexible gas connector that complies with the standard
for connectors for gas appliances, ANSI Z21.24.
Burner input requirements
Fire Hazard
Use a heavy metal vent.
Elevations up to 10,000 ft (3,048 m):
Do not use a plastic vent.
Do not use a metal foil vent.
■
The design of this dryer is certified by CSA International for
use at altitudes up to 10,000 ft (3,048 m) above sea level at
the Btu rating indicated on the model/serial number plate.
Burner input adjustments are not required when the dryer is
operated up to this elevation.
Failure to follow these instructions can result in death
or fire.
Elevations above 10,000 ft (3,048 m):
■
When installed above 10,000 ft (3,048 m) a 4% reduction of
the burner Btu rating shown on the model/serial number plate
is required for each 1,000 ft (305 m) increase in elevation.
WARNING: To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
Gas supply pressure testing
The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, attic, crawlspace, or a concealed space of
a building.
■
The dryer must be disconnected from the gas supply piping
system during pressure testing at pressures greater than
½ psi.
If using an existing vent system
■
Clean lint from the entire length of the system and make sure
exhaust hood is not plugged with lint.
■
■
Replace any plastic or metal foil vent with rigid metal vent.
Review Vent system chart. Modify existing vent system if
necessary to achieve the best drying performance.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Exhaust
Recommended hood styles are shown here.
If this is a new vent system
Vent material
B
■
Use a heavy metal vent. Do not use plastic or metal foil vent.
■
4" (102 mm) heavy metal exhaust vent and clamps must be
used. DURASAFE™ venting products are recommended.
A
4"
(102 mm)
4"
(102 mm)
4"
102 mm
A. Louvered hood style
B. Box hood style
4" (102 mm) heavy metal exhaust vent
The angled hood style (shown here) is acceptable.
DURASAFE™ vent products can be purchased from your
dealer or by calling Whirlpool Parts and Accessories. For
more information, see the “Assistance or Service” section.
4"
(102 mm)
Rigid metal vent
■
For best drying performance, rigid metal vents are
recommended.
2½"
(63.5 mm)
■
Rigid metal vent is recommended to avoid crushing and
kinking.
■
■
An exhaust hood should cap the vent to keep rodents and
insects from entering the home.
Elbows
Exhaust hood must be at least 12" (305 mm) from the ground
or any object that may be in the path of the exhaust (such as
flowers, rocks or bushes, snow line, etc.).
45° elbows provide better airflow than 90° elbows.
■
Do not use an exhaust hood with a magnetic latch.
Improper venting can cause moisture and lint to collect
indoors, which may result in:
Moisture damage to woodwork, furniture, paint, wallpaper,
carpets, etc.
Good
Better
Housecleaning problems and health problems.
Clamps
■
Use clamps to seal all joints.
■
Exhaust vent must not be connected or secure with screws or
other fastening devices that extend into the interior of the
duct and catch lint. Do not use duct tape.
Plan Vent System
Choose your exhaust installation type
Recommended exhaust installations
Typical installations vent the dryer from the rear of the dryer.
Other installations are possible.
Clamp
B
C
D
A
E
F
G
H
A. Dryer
B. Elbow
C. Wall
E. Clamps
F. Rigid metal vent
G. Vent length necessary to connect elbows
H. Exhaust outlet
D. Exhaust hood
†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number 4396011 - 18" (457.2 mm) to 29" (736.6 mm)
mismatch
Optional exhaust installations
This dryer can be converted to exhaust out the right side, left
side, or through the bottom. Contact your local dealer to have the
dryer converted.
Part Number 4396014 - 29" (736.6 mm) to 50" (1270 mm)
mismatch
Special provisions for mobile home installations
WARNING
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.
Fire Hazard
Cover unused exhaust holes with one of the
following kits:
279818 (white)
W10186596 (midnight grey)
Contact your local dealer.
Failure to follow these instructions can result in death,
fire, electrical shock, or serious injury.
Determine vent path
■
■
■
Select the route that will provide the straightest and most
direct path outdoors.
Plan the installation to use the fewest number of elbows and
turns.
When using elbows or making turns, allow as much room
as possible.
■
■
Bend vent gradually to avoid kinking.
Use the fewest 90° turns possible.
A
B
C
A. Standard rear offset exhaust installation
B. Left or right side exhaust installation
C. Bottom exhaust installation (not an option
with pedestal installations)
Determine vent length and elbows needed for best
drying performance
■
■
Use the following Vent system chart to determine type of vent
material and hood combinations acceptable to use.
Alternate installations for close clearances
Venting systems come in many varieties. Select the type best for
your installation. Two close-clearance installations are shown.
Refer to the manufacturer’s instructions.
NOTE: Do not use vent runs longer than those specified in
the Vent system chart. Exhaust systems longer than those
specified will:
■
■
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and
increased energy usage.
The Vent system chart provides venting requirements that will
help to achieve the best drying performance.
Vent system chart
NOTE: Side and bottom exhaust installations have a 90º turn
inside the dryer. To determine maximum exhaust length, add one
90º turn to the chart.
A
B
A. Over-the-top installation (also available with one offset elbow)
B. Periscope installation
Number of
90º turns
or elbows
Type of vent
Box or
Louvered
hoods
Angled
hoods
NOTE: The following kits for close clearance alternate
installations are available for purchase. To order, please see
the “Assistance or Service” section.
0
Rigid metal
Rigid metal
Rigid metal
Rigid metal
Rigid metal
64 ft (20 m)
58 ft (17.7 m)
1
2
3
4
54 ft (16.5 m) 48 ft (14.6 m)
44 ft (13.4 m) 38 ft (11.6 m)
35 ft (10.7 m) 29 ft (8.8 m)
■
Over-the-Top Installation:
Part Number 4396028
■
Periscope Installation (For use with dryer vent to wall vent
mismatch):
27 ft (8.2 m)
21 ft (6.4 m)
Part Number 4396037 - 0" (0 mm) to 18" (457.2 mm)
mismatch
10
Download from Www.Somanuals.com. All Manuals Search And Download.
For mobile home use
Gas dryers must be securely fastened to the floor at the time of
installation.
Install Vent System
1. Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
2. Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4" (102 mm) clamp.
3. Run vent to dryer location. Use the straightest path possible.
See “Determine vent path” in “Plan Vent System.” Avoid 90º
turns. Use clamps to seal all joints. Do not use duct tape,
screws, or other fastening devices that extend into the
interior of the vent to secure vent. Items sticking through the
vent can catch lint.
Mobile home installations require a Mobile Home Installation Kit.
For more information, please reference the service numbers in
the “Assistance or Service” section.
Install Leveling Legs
Level Dryer
Check the levelness of the dryer. Check levelness first side to
side, then front to back.
WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
1. To protect the floor, use a large flat piece of cardboard from
the dryer carton. Place cardboard under the entire back edge
of the dryer.
If the dryer is not level, prop up the dryer using a wood block.
Use a wrench to adjust the legs up or down and check again
for levelness.
2. Firmly grasp the body of the dryer (not the console panel).
Gently lay the dryer on the cardboard. See illustration.
Make Gas Connection
1. Remove the red cap from the gas pipe.
2. Using a wrench to tighten, connect the gas supply to the
dryer. Use pipe-joint compound on the threads of all non-
flared male fittings. If flexible metal tubing is used, be sure
there are no kinks.
A
B
3. Examine the leveling legs. Find the diamond marking.
A. Flared male fitting
B. Non-flared male fitting
4. Screw the legs into the leg holes by hand. Use a wrench to
finish turning the legs until the diamond marking is no longer
visible.
NOTE: For LP gas connections, you must use pipe-joint
compound resistant to the action of LP gas. Do not use
TEFLON®† tape.
5. Place a carton corner post from dryer packaging under each
of the 2 dryer back corners. Stand the dryer up. Slide the
dryer on the corner posts until it is close to its final location.
Leave enough room to connect the exhaust vent.
†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
A combination of pipe fittings must be used to connect the
dryer to the existing gas line. Shown is a recommended
connection. Your connection may be different, according to
the supply line type, size, and location.
2. Open the dryer door. Remove the 5 screws that hold the door
hinge on the front panel of the dryer.
A
C
B
D
A
A. Dryer front panel
B. Dryer door
C. Screws
B
C
A. 3/8" flexible gas connector
B. 3/8" dryer pipe
C. 3/8" to 3/8" pipe elbow
D. 3/8" pipe-to-flare adapter fitting
3. Remove the door.
4. Lay the dryer door on a flat, protected surface with the inside
door assembly facing up.
Remove the 5 screws to release the outer door assembly
from the inner door assembly, as indicated below. It is
important that you remove only the 5 indicated screws.
3. Open the shutoff valve in the supply line. The valve is open
when the handle is parallel to the gas pipe.
A
B
A. Closed valve
B. Open valve
4. Test all connections by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show a
leak. Correct any leak found.
Connect Vent
5. Lift the inner door assembly off of the outer door assembly.
Set the outer door assembly aside.
1. Using a 4" (102 mm) clamp, connect vent to exhaust outlet
in dryer. If connecting to existing vent, make sure the vent is
clean. The dryer vent must fit over the dryer exhaust outlet
and inside the exhaust hood. Check that the vent is secured
to exhaust hood with a 4" (102 mm) clamp.
Reverse the hinge
1. Place the inner door, screw head side up, on the work space.
2. Remove the 4 hinge screws that hold the hinge to the door
2. Move dryer into its final location. Do not crush or kink vent.
and remove hinge.
3. (On gas models) Check that there are no kinks in the flexible
A
B
C
gas line.
4. Once the exhaust vent connection is made, remove the
corner posts and cardboard.
Reverse Door Swing
You can change your door swing from a right-side opening to a
left-side opening, if desired.
NOTE: For ease of installation, you may want to use 2 or more
C
B
people to remove and reattach the dryer door.
A
Remove the door
1. Place a towel or soft cloth on top of the dryer or work space
to protect the surface.
A. Hinge side screw
B. Locator pins on hinge
C. Top side screw
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Move the large hole screw to the opposite side. Remove the
2 plug screws and plastic plugs, and insert them in the
original screw holes on the opposite side.
2. Reassemble the inner and outer door assemblies with the
5 screws.
A
C
B
3. Remove existing label from the opposite side of the door and
discard. Find label provided with the Use and Care Guide and
apply over original hinge holes.
A. Hinge screws
B. Large hole screw
C. Plug screws and plastic plugs
4. Move hinge to the other side and reattach with the 4 screws
removed in Step 2. Make sure locator pins line up in holes
and drive the top 2 screws in place first to help drive locator
pins into proper location.
4. Align the door by placing the locating tabs on the hinge with
the locating holes on the dryer front panel. Insert and tighten
the center hinge screw. The door will hang in place while you
insert and tighten the remaining 4 screws.
5. Set the inner door assembly aside.
Reverse the door handle
1. Place the outer door assembly face down on work space.
2. Remove the 6 screws that hold the intermediate door to the
outer door assembly. Remove the intermediate door, and set
hinge shield aside. Remove the hinge hole cover.
NOTE: Two or more people may be needed to reattach the
dryer door.
A
B
C
B
C
A. Dryer door
B. Dryer front panel
C. Insert this hinge screw first.
A
A. Intermediate door
B. Hinge shield
5. Close the door and check that it latches securely.
C. Hinge hole cover
6. Check for fingerprints on the glass. Clean the glass if
3. Rotate the window assembly 180º and reattach the
intermediate door, hinge shield, and hinge hole cover
with the 6 screws removed in Step 2.
necessary.
Complete Installation
Reinstalling the door
1. Check that all parts are now installed. If there is an extra part,
1. Place the inner door assembly into the outer door assembly.
To fit correctly, the inside door assembly edge is completely
inside the outside door assembly edge.
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Check the dryer’s final location. Be sure the vent is not
crushed or kinked.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Check that the dryer is level. See “Level Dryer.”
8. Read “Dryer Use.”
9. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
WARNING
10. Select a Timed Dry heated cycle, and start the dryer. Do not
select the Air Dry Temperature setting.
If the dryer will not start, check the following:
■
■
■
■
■
Controls are set in a running or “On” position.
Start button has been pushed firmly.
Dryer is plugged into a grounded 3 prong outlet.
Electrical supply is connected.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Household fuse is intact and tight, or circuit breaker has
not tripped.
■
Dryer door is closed.
11. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat. If you feel heat, cancel cycle and
close door. If you do not feel heat, turn off the dryer and
check that the gas supply line shutoff valve is open.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
■
If the gas supply line shutoff valve is closed, open it, then
repeat the 5-minute test as outlined above.
5. Plug into a grounded 3 prong outlet. Turn on power.
6. Remove any protective film or tape remaining on the dryer.
7. Dispose of/recycle all packaging materials.
■
If the gas supply line shutoff valve is open, contact a
qualified technician.
DRYER USE
Starting Your Dryer
WARNING
WARNING
Fire Hazard
Explosion Hazard
No washer can completely remove oil.
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Do not dry anything that has ever had anything
flammable on it (even after washing).
Items containing foam, rubber, or plastic must be dried
on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in death,
explosion, or fire.
Failure to follow these instructions can result in death
or fire.
Follow these basic steps to start your dryer. Please refer to
specific sections of this manual for more detailed information.
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
1. Clean lint screen before each load. See “Cleaning the Lint
Screen.”
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Place laundry in dryer and shut door.
■
Press MORE TIME or LESS TIME until the desired drying
time is displayed. Tap MORE TIME or LESS TIME, and the
time will change by 1-minute intervals. Press and hold
MORE TIME or LESS TIME, and the time will change by
5-minute intervals.
3. Press the POWER button. Then rotate the dial or press a
Timed Cycles button to select the desired Automatic or
Timed Cycle. The indicator light for the selected Automatic or
Timed cycle will glow green. The preset modifiers for the
selected cycle will glow green. Selectable options will glow
amber. If an option or modifier is unavailable with the selected
cycle, the light will not illuminate. The estimated or actual
cycle time
NOTE: The More Time and Less Time buttons can be
used only with Timed Cycles.
(in minutes) will show in the display.
To use an Automatic Cycle
NOTE: A light next to each feature will glow green when the
feature is selected or will glow amber when the feature is
selectable. The light will not glow when the selection is
unavailable with the cycle or option combinations selected.
■
Press TEMPERATURE until the desired temperature
glows.
NOTE: During a Timed Cycle, you can change the settings for
Time, Temperature, Wrinkle Prevent, and End of Cycle Signal.
Press STOP twice to stop the dryer and clear the settings.
Select another cycle or option.
■
■
Select an Automatic Cycle.
Select DRYNESS LEVEL to adjust how dry you want the
load. As the cycle runs, the control senses the dryness of
the load and adjusts the time automatically for the
selected dryness level.
4. (OPTIONAL STEP) If desired, select OPTIONS. For more
details, see “Options.”
NOTE: Most loads may be dried using Normal dryness
level, which is shown in bold letters on your control panel.
Normal is the energy preferred dryness level and will use
the least energy.
5. (OPTIONAL STEP) If desired, set the End of Cycle Signal
.
Select LOUD or SOFT by pressing the Cycle Signal button
to alert you when a cycle ends.
■
Select the desired Options.
6. Press and hold START for approximately 3 seconds until
dryer starts. Be sure the door is closed.
To make changes during an Automatic Cycle:
■
If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
■
■
Press STOP once.
Adjust Dryness Level.
■
If you wish to end your drying cycle after pressing Start,
press Stop twice.
NOTE: Dryness Level selections can be made only while
using Automatic Cycles. You can select a different
dryness level, depending on your load, by pressing
Dryness Level and choosing More Dry, Normal, or Less
Dry. Selecting More Dry, Normal, or Less Dry
Stopping Your Dryer
To stop your dryer at any time
Press STOP twice or open the door.
automatically adjusts the sensed time needed.
Pausing or Restarting
To pause the dryer at any time
Open the door or press STOP once.
To restart the dryer
Close the door. Press and hold START until dryer starts.
How Automatic Cycles work
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press START within 5 minutes. If the
cycle is interrupted for more than 5 minutes, the dryer will shut
off. Select new cycle settings before restarting the dryer.
The AccelerCare function improves drying performance with Auto
Moisture Sensing Plus, which advances the cycle as moisture is
extracted from clothing. A thermistor (electronic temperature
sensor) and moisture sensing strips in the dryer drum help
measure the amount of moisture in the clothes as they tumble.
An electronic control determines the load type to help save time,
avoid overdrying, and increase the accuracy of the end dryness
level. After the first 5 minutes of an automatic cycle, the
estimated time display will adjust based on the approximate load
size, cycle, dryness level selected, and amount of moisture left in
the clothes. When the clothes have reached approximately 80%
of the dryness level selected, the estimated time display will
adjust again, showing the final drying time. Auto Moisture
Sensing Plus takes the guesswork out of drying time and
enhances fabric care.
Control Locked
This feature allows you to lock your settings to avoid unintended
use of the dryer. You can also use the Control Locked feature to
avoid unintended cycle or option changes during dryer operation.
To enable the Control Locked feature:
Press and hold CYCLE SIGNAL for 3 seconds. The Control
Locked indicator light glows, and a single beep tone is heard.
To unlock, press and hold CYCLE SIGNAL for 3 seconds.
The indicator light turns off.
To use a Timed Cycle
NOTE: A light next to each feature will glow green when the
feature is selected or will glow amber when the feature is
selectable. The light will not glow when the selection is
unavailable with the cycle or option combinations selected.
Drying and Cycle Tips
Select the correct cycle and dryness level or temperature for your
load. If an Automatic Cycle is running, the display shows the
estimated cycle time, which is determined by your dryer
automatically sensing the dryness level of your load. If a Timed
Cycle is running, the display shows the exact number of minutes
remaining in the cycle.
■
Press a Timed Cycles button or, to select Air Fluff, rotate
the control knob to the desired cycle.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Cool Down
The Cool Down light glows green during the cool down part of
the cycle. Laundry cools for ease in handling.
Clothes Dry
Drying tips
The Clothes Dry light glows green when the drying cycle is
finished. This indicator stays on during Wrinkle Prevent.
■
Follow care label directions when they are available.
■
If desired, add a fabric softener sheet. Follow package
instructions.
Wrinkle Prevent
■
■
To reduce wrinkling, remove the load from the dryer as soon
as tumbling stops. This is especially important for permanent
press, knits, and synthetic fabrics.
The Wrinkle Prevent light glows green when this option is
selected. This indicator stays on with Clothes Dry.
Sensing/Revising Est. Time
Avoid drying heavy work clothes together with lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.
The Sensing/Revising Est. Time light glows green when moisture
sensing strips in the dryer drum are measuring the amount of
moisture in the clothes. The estimated time display may adjust
to show a more accurate drying time.
Cycle tips
■
Dry most loads using the preset cycle settings.
Indicator lights
■
Refer to the Automatic or Timed Cycles Preset Settings chart
(in the “Cycles” section) for a guide to drying various loads.
Other indicator lights show Cycle, Options, Modifiers, End of
Cycle, and Control Lock settings selected. The display shows
the estimated or actual time remaining.
■
Drying temperature and Dryness Level are preset when
you choose an Automatic Cycle. You can select a
different dryness level, depending on your load, by
pressing Dryness Level and choosing More Dry, Normal,
or Less Dry.
Cycles
Select the drying cycle that matches the type of load you are
drying. See Automatic Dry chart or Timed Preset Cycle Settings
chart.
NOTE: You cannot use the Timed Cycle Adjust and you
cannot modify temperature with the Automatic cycles.
■
If you wish to adjust the cycle length of a Timed Cycle,
press More Time or Less Time. Adjust the temperature of
a Timed Cycle by pressing TEMPERATURE until the
desired temperature is selected.
NOTE: You cannot use the Dryness Level with Timed
Cycles.
Status Lights
You may follow the progress of your dryer with the drying Status
indicator lights.
Automatic Cycles
Automatic Cycles allow you to match the cycle to the load you
are drying. See the following Automatic Dry Preset Cycle Settings
chart. Each cycle dries certain fabrics at the recommended
temperature. A sensor detects the moisture in the load and
automatically adjusts the drying time for optimal drying.
Timed Cycle
The Timed Cycle light glows green during a Timed Cycle.
Heavy Duty
Use this cycle to get high heat for heavyweight mixed loads,
cotton towels, or bedspreads.
Wet
The Wet light glows green at the beginning of Automatic Cycle if
a wet item is detected or in a timed cycle after 5 minutes.
Denim
■
■
In an Automatic Cycle, if a wet item is not detected after
5 minutes, the dryer will run for a preset minimum run time
(based on the selected cycle and dryness level setting) and
then go into Cool Down. The Cool Down and Wrinkle Prevent
indicators will glow green, if selected.
Use this cycle to get medium high heat for drying denims.
Normal
Use this cycle to get medium heat for drying sturdy fabrics such
as work clothes and sheets.
In a Timed Cycle, the Wet light will glow green after 5 minutes
and remain on until the dryer enters Cool Down.
Casual
Use this cycle to get low heat for drying no-iron fabrics, such
as sport shirts, casual business clothes, and permanent press
blends.
Damp
The Damp light glows green in an Automatic Cycle when the
laundry is approximately 80% dry. This is useful when you want
to remove lightweight items in a mixed load to avoid overdrying
or remove partially dry items that may need ironing. To be alerted
when the load is about 80% dry, you may use the damp dry
signal option. See Damp Dry Signal in “Options.”
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Delicate
Air Fluff
Use this cycle to get extra-low heat to gently dry items such as
lingerie, blouses, or washable knit fabrics.
Rotate the dial to Air Fluff to use this cycle for items that require
drying without heat such as rubber, plastic, and heat-sensitive
fabrics. This table shows examples of items that can be dried
using Air Fluff. The temperature setting is not adjustable with
this cycle.
Automatic Dry Preset Cycle Settings
Automatic Cycles
Load Type
Temperature
Time*
(Minutes)
Type of Load
Time*
(Minutes)
HEAVY DUTY
High
45
Heavyweight mixed loads,
cotton towels, bedspreads
Foam rubber - pillows, padded bras, stuffed toys 20 - 30
Plastic - Shower curtains, tablecloths
Rubber-backed rugs
20 - 30
40 - 50
10 - 20
DENIM
Denim jeans, jackets
Medium High
Medium
55
40
Olefin, polypropylene, sheer nylon
NORMAL
Corduroys, work clothes,
sheets
*Reset cycle to complete drying, if needed.
When using Air Fluff
CASUAL
Permanent press,
synthetics
Low
35
30
■
■
■
Check that coverings are securely stitched.
Shake and fluff pillows by hand periodically during the cycle.
Dry item completely. Foam rubber pillows are slow to dry.
DELICATE
Extra Low
Lingerie, blouses, washable
knit fabrics
Timed Preset Cycle Settings
Timed Cycles
Load Type
Default
Temperature
Default Time
(Minutes)
*Estimated Time with Dryness Level (Normal) setting. Time will
vary depending on load type and load size.
TIMED DRY
Heavyweight, bulky items,
bedspreads, work clothes
High
40
Timed Cycles
Use Timed Cycles to select a specific amount of drying time and
a drying temperature. (Temperatures are not selectable with Air
Fluff.) When a Timed Cycle is selected, the Estimated Time
Remaining display shows the actual time remaining in your cycle.
You can change the actual time in the cycle by pressing More
Time or Less Time. See “Changing Cycles, Options, and
Modifiers.”
QUICK DRY
High
23
20
Small loads
TOUCH UP
Helps to smooth out
wrinkles
Medium High
AIR FLUFF
Dry without heat
Air Dry
(no heat)
36
Timed Dry
Use this cycle to complete drying if items are still damp after an
Automatic Cycle. Timed Dry is also useful for drying heavyweight
and bulky items, such as bedspreads and work clothes.
Lightweight garments, such as exercise wear, can be dried using
Timed Dry on a low temperature setting.
*Use the Air Fluff cycle for items that require drying without heat
such as rubber, plastic, and heat-sensitive fabrics.
Options
You can customize your cycles by selecting options. Not all
Options are available with all cycles. Current selections will glow
green. If an option is unavailable with a selected cycle, the light
will not illuminate when pressed and an error sound will be heard.
Quick Dry
Use this cycle for drying small loads or loads that need a short
drying time.
Touch Up
Use this cycle to help smooth out wrinkles from items, such as
clothes packed in a suitcase or items wrinkled from being left in
the dryer too long.
Wrinkle Prevent
Wrinkle Prevent helps smooth out wrinkles that form when you
cannot unload the dryer promptly at the end of a cycle. During
this option, the dryer stops tumbling and then tumbles again for
a brief period.
■
Press WRINKLE PREVENT to get up to 2 hours of heat-free,
periodic tumbling at the end of a cycle.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
■
■
Stop Wrinkle Prevent at any time by pressing WRINKLE
PREVENT or opening the dryer door.
Dryness Level
Press DRYNESS LEVEL until the desired Dryness Level is
selected. Dryness Level cannot be adjusted with Timed Cycles.
For the Casual cycle, Wrinkle Prevent is preset to ON.
The other cycles will retain the Wrinkle Prevent setting.
For example, if you select Wrinkle Prevent in the Normal
cycle, Wrinkle Prevent will be on the next time you select the
Normal cycle.
NOTE: If you do not select Wrinkle Prevent, the dryer stops
after cool down.
Damp Dry Signal
Select the Damp Dry Signal to alert you that your clothes are
approximately 80% dry. This is useful when you want to remove
lightweight items in a mixed load to avoid overdrying or remove
partially dry items that may need ironing.
Changing Cycles, Options, and Modifiers
You can change Automatic Cycles, Timed Cycles, Modifiers, and
Options anytime before pressing Start.
■
Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
NOTE: The Damp Dry Signal is available only with the Automatic
Cycles.
Changing Cycles after pressing Start
Button Sounds
1. Press STOP twice. This ends the current cycle.
You can change the volume of the sound of the beeps. Press
BUTTON SOUNDS until the desired volume (Loud, Soft, or Off)
glows. The Power and Cancel buttons will still beep softly when
the Button Sounds volume is set to Off.
2. Select the desired cycle and options.
3. Press and hold START. The dryer starts at the beginning of
the new cycle.
NOTE: If you do not press START within 5 minutes of selecting
Drum Light
the cycle, the dryer automatically shuts off.
Press DRUM LIGHT to turn on the light inside the dryer drum.
During a cycle, if Drum Light is selected, the drum light turns on
and will remain on until Drum Light is pressed again, the door is
open and closed, or the door is left open for 5 minutes.
Changing Modifiers and Options after pressing Start
You can change a Modifier or Option anytime before the selected
Modifier or Option begins.
When the dryer is not running, the drum light will turn on when
Drum Light is pressed or the dryer door is opened, and it will
remain on until the dryer door has been open for 5 minutes, the
dryer door is closed or Drum Light is pressed again.
1. Press STOP once.
2. Select the new Modifier and/or Option.
3. Press and hold START to continue the cycle.
Press DRUM LIGHT at any time to turn the drum light ON or OFF.
NOTE: If you happen to press Stop twice, the program clears and
your dryer shuts down. Restart the selection process.
Modifiers
Changing the Preset Dryness Level Settings
Use Modifiers to select time, temperatures, and dryness levels for
the Timed Cycles. Not all Modifiers are available with all options
and cycles. Available modifier settings will glow amber. Current
selections will glow green. If a modifier is unavailable with a
selected cycle, the light will not illuminate.
If all of your loads on all Automatic Dry cycles are consistently not
as dry as you would like, you may change the preset Dryness
Level settings to increase the dryness. This change will affect all
of your Automatic Dry cycles.
Your Dryness Level settings can be adjusted to adapt to different
installations, environmental conditions or personal preference.
There are 3 drying settings: 1 (factory preset dryness level),
2 (slightly dryer clothes, approximately 15% more drying time),
and 3 (much dryer clothes, approximately 30% more drying
time).
Time
Press MORE TIME or LESS TIME until the desired drying time is
displayed. The time cannot be changed with Automatic Cycles.
1. The Dryness Level settings cannot be changed while the
dryer is running.
2. Press and hold the DRYNESS LEVEL button for 5 seconds.
The dryer will beep, and “CF” will be displayed for 1 second
followed by the current drying setting.
3. To select a new drying setting, press the DRYNESS LEVEL
button again until the desired drying setting is shown.
NOTE: While you are cycling through the settings, the current
setting will not flash, but the other settings will flash.
Temperature
Press TEMPERATURE until the desired temperature setting
glows. Temperature modifiers cannot be used with the Automatic
Cycles or the Air Fluff cycle.
4. Press START to save the drying setting.
The drying setting you selected will become your new preset
drying setting for all Automatic Dry cycles.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Place wet items on top of the rack. Allow space around items
for air to circulate. The rack does not move, but the drum will
rotate. Make sure items do not hang over the edges or
between rack grille.
End of Cycle Signal
End of Cycle Signal
The End of Cycle Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the end
of the cycle reduces wrinkling.
4. Close the door.
5. Rotate the dial to the Air Fluff cycle or press Timed Dry.
Select a drying time by pressing MORE TIME or LESS TIME.
Press TEMPERATURE until the desired temperature glows.
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using the Air Fluff cycle. Refer to the
following table.
Press CYCLE SIGNAL to adjust the sound level or turn off the
signal.
NOTE: When Wrinkle Prevent is selected and the End of Cycle
Signal is on, a tone sounds every 5 minutes until the clothes are
removed, or Wrinkle Prevent ends.
6. When Air Fluff is selected, the Estimated Time Remaining
display shows the default time. You can change the actual
time in the cycle by pressing More Time or Less Time.
Drying Rack Options
7. Start the dryer.
NOTE: Check the lint screen and remove any lint accumulated
from items dried on the rack after the cycle is finished.
The drying rack is useful for drying items you would not
necessarily want to tumble dry or that you would normally line dry
(for example, sweaters).
Dryer Rack
Cycle
Temp.
Time*
If your model does not have a drying rack, you may be able to
purchase one for your model. To find out whether your model
allows drying rack usage and for information on ordering, please
refer to the front page of the manual or contact the dealer from
whom you purchased your dryer.
Wool Sweaters
Timed Dry Low
60
Block to shape and lay flat
on the rack
The dryer rack is recommended for use with the Air Fluff cycle or
with Timed Dry cycles. The dryer rack cannot be used with
Automatic Cycles.
Stuffed toys or pillows
Cotton or polyester fiber
filled
Timed Dry Low
60
To use the heated dryer rack:
Do not remove the lint screen.
1. Open dryer door.
Stuffed toys or pillows
Air Fluff
Air Fluff
Air Only
(no heat)
90
90
Foam rubber filled
Sneakers or canvas
shoes
Air Only
(no heat)
*Reset cycle to complete drying if needed.
NOTE: You must remove rack for normal tumbling. To remove the
dryer rack, lift it straight up and out of the dryer.
A
A. Front edge
2. Place dryer rack over the bottom of the dryer door opening.
Rest the back wire on the dryer back ledge. Push down on
the frame front to secure over lint screen.
B
A
A. Dryer rack front edge
B. Dryer back panel
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER CARE
To wash
1. Roll lint off the screen with your fingers.
2. Wet both sides of lint screen with hot water.
Cleaning the Dryer Location
Keep dryer area clear and free from items that would obstruct the
flow of combustion and ventilation air.
3. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel. Replace screen
in dryer.
Cleaning the Dryer Interior
To clean dryer drum
Cleaning the Lint Screen
1. Make a paste with powdered laundry detergent and very
warm water.
Every load cleaning
2. Apply paste to a soft cloth.
The lint screen is located in the door opening of the dryer. The
control panel has an indicator light to remind you to clean the lint
screen before each load. A screen blocked by lint can increase
drying time.
OR
Apply a liquid, nonflammable household cleaner to the
stained area and rub with a soft cloth until all excess dye and
stains are removed.
To clean
3. Wipe drum thoroughly with a damp cloth.
1. Pull the lint screen straight up. Roll lint off the screen with
your fingers. Do not rinse or wash screen to remove lint.
Wet lint is hard to remove.
4. Tumble a load of clean cloths or towels to dry drum.
NOTE: Garments that contain unstable dyes, such as denim blue
jeans or brightly colored cotton items, may discolor the dryer
interior. These stains are not harmful to your dryer and will not
stain future loads of clothes. Dry unstable dye items inside out to
avoid transfer of dye.
Removing Accumulated Lint
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
2. Push the lint screen firmly back into place.
IMPORTANT:
From the Exhaust Vent
Lint should be removed every 2 years, or more often, depending
on dryer usage.
■
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
Vacation and Moving Care
■
If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint. See “Venting
Requirements.”
Vacation care
As needed cleaning
Operate your dryer only when you are at home. If you will be on
vacation or not using your dryer for an extended period of time,
you should:
Laundry detergent and fabric softener residue can build up on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off while the screen
is in the dryer.
1. Unplug dryer or disconnect power.
2. Close shutoff valve in gas supply line.
3. Clean lint screen. See “Cleaning the Lint Screen.”
Clean the lint screen with a nylon brush every 6 months, or more
frequently, if it becomes clogged due to a residue buildup.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Open the dryer door. Locate the light bulb cover on the back
wall of the dryer. Remove the screw located in the lower right
corner of the cover. Remove the cover.
Moving care
1. Unplug the power supply cord.
2. Close shutoff valve in gas supply line.
3. Disconnect gas supply line pipe and remove fittings attached
to dryer pipe.
4. Cap the open fuel supply line.
5. Make sure leveling legs are secure in dryer base.
6. Use masking tape to secure dryer door
Changing the Drum Light
The dryer light automatically turns on inside the dryer drum when
you open the door.
3. Turn bulb counterclockwise. Replace the bulb with a 10-watt
appliance bulb only. Replace the cover and secure with the
screw.
To change the drum light
1. Unplug dryer or disconnect power.
4. Plug in dryer or reconnect power.
TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
■
■
■
Is a coin, button, or paper clip caught between the drum
and front or rear of the dryer?
Dryer Operation
Check the front and rear edges of the drum for small objects.
Clean out pockets before laundering.
Dryer will not run
Are the four legs installed, and is the dryer level front to
back and side to side?
The dryer may vibrate if not properly installed. See the
Installation Instructions.
■
■
Has a household fuse blown, or circuit breaker tripped?
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
Is the clothing knotted or balled up? When balled up, the
load will bounce, causing the dryer to vibrate. Separate the
load items, and restart the dryer.
Was a regular fuse used?
Use a time-delay fuse.
■
■
Is the dryer door firmly closed?
Was the Start button firmly pressed?
Large loads may require pressing and holding the Start
button for 2-5 seconds.
Dryer displaying code message
■
■
“PF” (power failure), check the following:
Was the drying cycle interrupted by a power failure?
Press and hold START to restart the dryer.
No heat
“F” Variable (F1, F2, F20) service codes:
Call for service.
■
■
Has a household fuse blown, or has a circuit breaker
tripped?
The drum may be turning, but you may not have heat.
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
Is the valve open on the gas supply line?
Unusual sounds
■
■
Has the dryer had a period of non-use?
If the dryer hasn’t been used for a while, there may be a
thumping sound during the first few minutes of operation.
Is it a gas dryer?
The gas valve clicking is a normal operating sound.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
■
Is the dryer located in a closet?
Closet doors must have ventilation openings at the top and
bottom of the door. The front of the dryer requires a minimum
of 1" (25 mm) of airspace, and, for most installations, the rear
of the dryer requires 5" (127 mm). See “Installation
Instructions.”
Dryer Results
Clothes are not drying satisfactorily, drying times are too
long, or load is too hot
■
■
Has an air dry cycle been selected?
Select the right cycle for the types of garments being dried.
See “Modifiers.”
■
Is the lint screen clogged with lint?
Lint screen should be cleaned before each load.
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
WARNING
Cycle time too short
WARNING
Excessive Weight Hazard
Fire Hazard
Use a heavy metal vent.
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
■
Is the automatic cycle ending early?
The load may not be contacting the sensor strips. Level the
dryer.
Change the dryness level setting on Automatic Cycles.
Increasing or decreasing the dryness level will change the
amount of drying time in a cycle.
■
Is the exhaust vent or outside exhaust hood clogged
with lint, restricting air movement?
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not
feel air movement, clean exhaust system of lint or replace
exhaust vent with heavy metal or flexible metal vent. See
“Venting Requirements.”
Do not use a dryer rack with an automatic cycle.
Lint on load
■
■
Are fabric softener sheets blocking the lint screen grille?
■
■
Is the lint screen clogged?
Use only one fabric softener sheet, and use it only once.
Clean lint screen. Check for air movement.
Is the exhaust vent the correct length?
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See “Plan Vent
System.”
Stains on load or drum
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments.
■
Is the exhaust vent diameter the correct size?
Use 4" (102 mm) diameter vent material.
Drum stains are caused by dyes in clothing (usually blue
jeans). This will not transfer to other clothing.
Loads are wrinkled
■
■
Was the load removed from dryer at the end of the cycle?
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
Odors
■
Have you recently been painting, staining, or varnishing
in the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
■
Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
For Assistance and Service
Call Maytag Services, LLC Customer Assistance toll free:
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
Our consultants provide assistance with:
■
■
■
■
■
Features and specifications on our full line of appliances.
Installation information.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only factory specified parts. Factory specified parts will fit
right and work right because they are made with the same
precision used to build every new MAYTAG® appliance.
Use and maintenance procedures.
Accessory and repair parts sales.
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
To locate factory specified parts in your area, call the following
customer assistance telephone number or your nearest
designated service center.
■
Referrals to local dealers, repair parts distributors and service
companies. Maytag® appliances designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in the United States.
To locate the Maytag® appliances designated service
company in your area, you can also look in your telephone
directory Yellow Pages.
For further assistance
If you need further assistance, you can write to Maytag®
appliances with any questions or concerns at:
Maytag Services, LLC
Attn: CAIR® Center
P.O. Box 2370
Cleveland, TN 37320-2370
Please include a daytime phone number in your correspondence.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
AMANA® LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Amana brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “Amana”) will pay for factory
specified parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased.
Service must be provided by a Amana designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada
and applies only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required
to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is
used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty
coverage.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Amana.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Amana within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Amana servicer is not available.
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with Amana’s published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or
cannot be easily determined.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This
warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
AMANA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Amana dealer to determine if another warranty applies.
If you think you need repair service, first see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the
problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by calling
Amana. In the U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777.
6/08
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Dealer name____________________________________________________
Address________________________________________________________
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
W10216187A
7/08
Printed in U.S.A.
®Registered trademark/™ Trademark of Maytag Corporation or its related companies.
© 2008
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|