MULTITASKER®
MANUAL PART NUMBER: 400-0372-005
MT107-303
8-OUT, TWISTED PAIR, SINGLE CHANNEL
OUTPUT CARD FOR MATRIX SWITCHER
USER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
PRECAUTIONS / SAFETY WARNINGS
1
·
This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when the
Please read this manual carefully before using your
MT107-303. Keep this manual handy for future
reference. These safety instructions are to ensure
the long life of your MT107-303 and to prevent fire
and shock hazards. Please read them carefully and
heed all warnings.
equipment is operated in
a
commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions found herein, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
1.1 GENERAL
·
Qualified ALTINEX service personnel or their
authorized representatives must perform all
service.
1.2 INSTALLATION
·
To prevent fire or shock, do not expose this unit
to water or moisture. Do not place the
MT107-303 in direct sunlight, near heaters, or
heat-radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam can
harm internal components.
·
Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
·
·
·
Handle the MT107-303 carefully. Dropping or
jarring can damage the card.
Do not pull any cables that are attached to the
MT107-303.
Insert the card carefully into the slots of the
MultiTasker without bending any edges.
1.3 CLEANING
·
Clean only the connector area with a dry cloth.
Never use strong detergents or solvents such as
alcohol or thinner. Do not use a wet cloth or
water to clean the card. Do not clean or touch
any component or PCB.
1.4 FCC NOTICE
·
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
400-0372-005
2
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
ABOUT YOUR MT107-303
2
TECHNICAL SPECIFICATIONS
3
Specifications are subject to change.
MT107-303
8-Out, Twisted Pair, Single Channel
FEATURES/
MT107-303
The MT107-303 is an 8 Output expansion card for
use with the MT107-104 64X64 Matrix Engine. The
MT107-303 outputs are single channel differential
outputs for use over long cable lengths. The
Twisted Pair signals from the MT107-303 may be
easily combined into a single CAT-5 cable using
ALTINEX MS8704TP adapter cables. The CAT-5
cable is then run to an ALTINEX Twisted Pair
receiver such as the DA1931CT.
DESCRIPTION
GENERAL
Input
Twisted Pair
Internal Box Header (1)
RJ-45 female (8)
Output Connectors
Twisted Pair
Compatibility
ALTINEX Standard for
Twisted Pair
Signal Types
Each MT107-303 connects to an output connector
on the MT107-104 Matrix Engine. Up to 8
MT107-303 cards may be connected to the engine
and each card is connected with the engine via
specially provided, high-bandwidth video cables.
Video Signal
Resolutions
VGA through UXGA
480p through 1080i
VGA:
640x480@60Hz
900 ft (274 m)
Recommended Max.
Cable Lengths
Note: Measurements
made using ALTINEX
low-skew cable,
As part of the MT107-104 Matrix Engine, the
MT107-303 has special built-in features. Signal
detection circuitry allows the user to determine the
presence of an output signal on any channel.
XGA: 1024x768@60Hz
700 ft (213 m)
SXGA: 1280x1024@60Hz
650 ft (198 m)
CB3150PV.
Output signals are driven by high-speed,
high-bandwidth differential amplifiers.
UXGA: 1600x1200@60Hz
600 ft (183 m)
ALTINEX’s software and hardware allow for the
switching of any input to output combination and
prevents illegal switching combinations that may
damage components.
Table 1. MT107-303 General
MECHANICAL
Enclosure Slots Required
Weight
MT107-303
1
The latest generation of Twisted Pair devices uses
an innovative, patented technology* developed by
ALTINEX. The new signal processing technology
allows transmitting and receiving fully equalized
computer video signals, stereo, and audio signals
over long distances.
0.4 lb (0.18 kg)
Black Anodized
10°C-50°C
Connector Panel
T° Operating
T° Maximum
75°C
Humidity
90% non-condensing
38,000 hrs
* US Patent 7,065,190
MTBF (calc.)
Table 2. MT107-303 Mechanical
400-0372-005
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
ELECTRICAL
Output
MT107-303
Video/Sync/Audio Signals
ALTINEX Standard
Twisted Pair
Analog Signal Level
Input
1.5 Vp-p max.
Bus from Matrix Engine
0 dB gain
Power Consumption (from enclosure)
+6V
0.225 A (1.3 W)
-6V
0.190 A (1.1 W)
2.4 W max.
Total Power
Table 3. MT107-303 Electrical
400-0372-005
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
PRODUCT DESCRIPTION
4
8 1TP OUTPUTS
BOTTOM RETAINER SCREW
400-0372-005
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
APPLICATION DIAGRAMS
DIAGRAM 1: TYPICAL SETUP
5
MT107-303
400-0372-005
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
DIAGRAM 2: INTERNAL VIEW
POWER
IN1
IN2
IN3
OUT1
OUT2
OUT3
IN4
OUT4
INPUT
TWISTED
40-PIN
IDC
PAIR
RJ-45
IN5
IN6
IN7
IN8
OUT5
OUT6
OUT7
OUT8
SIGNAL
DETECT
400-0372-005
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
INSTALLING YOUR MT107-303
6
OPERATION
7.1 RS-232 CONTROL
The MT107-303
7
Step 1. Turn off power to the MultiTasker
enclosure and remove the input AC power
cord.
has
many
advanced
remote-control capabilities as part of an
MT107-104 Matrix Switcher. These capabilities
are accessible through standard RS-232
communication. The actual controlling can be
Step 2. Locate the MT107-104 currently installed
in the MultiTasker. Verify there is an
empty slot in the enclosure for the new
MT107-303 card.
accomplished through
a
computer control
system or any other device capable of sending
RS-232 commands.
The MT107-303 must be installed directly
to the right of the MT107-104 Matrix
Engine. For example, if the engine is
installed in slots 9 and 10, the first
MT107-303 output card should be
installed in slot 11, the second in slot 12,
and so on.
7.2 DESCRIPTION OF COMMANDS
Please see the MT107-104 User's Guide for a
full listing of commands available for the
MT107-303 as part of a MultiTasker Matrix
Switcher.
Step 3. Route the ribbon cables through the notch
in the add-on boards and connect to the
MT107-104 base assembly using the
special high-bandwidth cables provided
with the engine. Make sure the cable
connector is secured in the socket of the
output connector card.
TROUBLESHOOTING GUIDE
8
We have carefully tested and found no problems in
the supplied MT107-303. However, we would like to
offer suggestions for the following:
8.1 NO DISPLAY
Cause 1: The source has a problem.
Step 4. Attach the opposite end of the ribbon
cable to the card and carefully slide the
MT107-303 into the empty slot in the
MultiTasker enclosure.
Solution: Check the source and make sure
that there is a signal present and all
source connections are correct. If
the source is working and there is
still no display, see Cause 2.
Step 5. Secure the card by tightening the retainer
screws at the top and bottom.
Cause 2: The input signal is not detected.
Step 6. Connect the output of the MT107-303 to
the input of a Twisted Pair receiver using
ALTINEX cable part number MS8704TP.
Solution 1: In AVSnap®, or other control
software, send the [SDI] command.
This command is detailed in the
MT107-104's User Guide. Verify a
signal is detected for the output
number in question. If a signal is not
detected, see Solution 2.
Step 7. Restore AC power to the enclosure.
Step 8. The MT107-303 is now ready for
operation.
Solution 2: Verify the MT107-303 is connected
to the MT107-104 and that the cable
is in good condition. If a signal is
detected, see Cause 3. If there is no
signal
detected,
please
call
ALTINEX at (714) 990-2300.
400-0372-005
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
Cause 3: The path is not selected.
ALTINEX POLICIES
9
Solution: Make sure the input to output path is
9.1 LIMITED WARRANTY/RETURN POLICIES
correctly selected.
Please see the ALTINEX website at
www.altinex.com for details on warranty and
return policies.
For example, Input 2 is connected to
Output 1 in the Matrix Engine status.
Physically, the source signal should
be connected to Input 2 and the
display cable should be connected
to Output 1. See RS-232 accessible
commands in Section 7 of the
9.2 CONTACT INFORMATION
ALTINEX, Inc.
592 Apollo Street
MT107-104 User’s
command details.
Guide for
Brea, CA 92821 USA
TEL: 714 990-2300
If no display is present, see
Cause 4.
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: [email protected]
Cause 4: Cable connections are incorrect.
Solution: Make sure that cables are properly
connected. Also, make sure that the
continuity and wiring are good. If
there is still no display present, see
Cause 5.
Cause 5: The display has a problem.
Solution: Make sure the display is powered
and is turned on. If there is still no
display, please call ALTINEX at
(714) 990-2300.
400-0372-005
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|