DISTRIBUTION AMPLIFIERS
MANUAL PART NUMBER: 400-0003-003
PRODUCT REVISION: 1
DA1203RM
1-IN, 3-OUT RGBS
DISTRIBUTION AMPLIFIER
USER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
DISTRIBUTION AMPLIFIERS
to a table or wall, use only Altinex made
PRECAUTIONS / SAFETY WARNINGS
1
mounting accessories (Rack Mount Shelf
DA1298FC, Rack Mount Ears DA1299RM) and
cables for optimum setup.
Please read this manual carefully before using your
DA1203RM Distribution Amplifier. Keep this
manual handy for future reference. These safety
instructions are to ensure the long life of your
DA1203RM and to prevent fire and shock hazard.
Please read them carefully and heed all warnings.
·
To turn off main power, be sure to remove the
cord from power outlet. The power outlet socket
should be installed as near to the equipment as
possible, and should be easily accessible.
1.1 GENERAL
·
·
Do not pull power cord or any cable that is
attached to the DA1203RM Distribution
Amplifier.
·
Unauthorized personnel shall not open the unit
since there are high-voltage components inside.
If the DA1203RM Distribution Amplifier is not to
be used for an extended period of time,
disconnect the power cord from the power
outlet.
·
Qualified Altinex service personnel, or their
authorized representatives must perform all
service.
1.2 SAFETY GUIDELINES FOR THE RACK-
MOUNTING OF THE DA1203RM
1.4 CLEANING
·
Unplug the DA1203RM power cord before
cleaning. Clean surfaces with a dry cloth. Never
use strong detergents or solvents such as
alcohol or thinner. Do not use a wet cloth or
water to clean the unit.
·
·
·
Maximum operating ambient temperature is 35
(degrees C).
Never restrict the air flow through the devices’
fan or vents.
When installing equipment into a rack,
distribute the units evenly. Otherwise,
hazardous conditions may be created by an
uneven weight distribution.
1.5 FCC / CE NOTICE
·
·
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
·
·
Connect the unit to a properly rated supply
circuit.
Reliable Earthing (Grounding) of Rack-
Mounted Equipment should be maintained.
1.3 INSTALLATION
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
·
For best results, place the DA1203RM
Distribution Amplifier on a flat, level surface in a
dry area away from dust and moisture.
·
To prevent fire or shock, do not expose this unit
to rain or moisture. Do not place the DA1203RM
Distribution Amplifier in direct sunlight, near
heaters or heat radiating appliances, or near any
liquid. Exposure to direct sunlight, smoke, or
steam can harm internal components.
equipment is operated in
a
commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
·
·
Handle the DA1203RM Distribution Amplifier
carefully. Dropping or jarring can damage
internal components.
Do not place heavy objects on top of the
DA1203RM. If the DA1203RM is to be mounted,
2
Download from Www.Somanuals.com. All Manuals Search And Download.
DISTRIBUTION AMPLIFIERS
TECHNICAL SPECIFICATION
3
·
Any changes or modifications to the unit not
expressly approved by Altinex, Inc. could void
the user’s authority to operate the equipment.
FEATURES/DESCRIPTION
GENERAL
DA1203RM
1
Inputs
Input Connector
Outputs
Output Connectors
Compatibility
ABOUT YOUR DISTRIBUTION AMPLIFIER 2
4-BNC Female
3
Three 4-BNC Female
High resolution RGBS,
RGsB and RsGsBs,
Component, S-Video
and Composite Video
The DA1203RM Distribution Amplifier is designed
to allow the connection of a single computer or
other video source to as many as three scan-rate
compatible display devices.
Though primarily designed to pass RGBS format
signals, the DA1203RM can also pass RGsB,
Component Video (Y, R-Y, B-Y), S-Video (Y/C),
and Composite Video by using the appropriate
analog channels (Red, Green, Blue).
Table 1. DA1203RM General
MECHANICAL
DA1203RM
Material
Finish
Top Panel
0.1” Al
Gray
Lexan
The analog channels (Red, Green, Blue) are
designed to pass video levels up to 1.5V p-p
offering a 0.15% differential gain and 0.16 degree
differential phase to assure the highest quality
video signal.
Height (inches)
Width (inches)
Depth (inches)
Weight (pounds)
Ship Weight (pounds)
T° Operating
T° Maximum
Humidity
3.40in (86mm)
8.50in (216mm)
4.75in (121mm)
2.6lbs (1.18kg)
3.8lbs (1.73kg)
10°C-35°C
The DA1203RM offers switches for Gain, Sync
Level, and Sync Polarity. The Gain Switch boosts
the output of the amplifier by 35% for use, with long
cable runs. The DA1203RM uses AGC (automatic
gain control) circuitry, which converts all incoming
sync levels to either 4V p-p or 2V p-p. This AGC
circuitry is selectable with the Sync Level switch.
This enables it to be compatible, with current and
older display equipment. The Sync Polarity switch
reverses the polarity of the incoming sync for
compatibility with various displays.
50°C
90% non-condensing
MTBF (calculations)
40,000 hrs
Table 2. DA1203RM Mechanical
ELECTRICAL
DA1203RM
Input Video Signals
Analog Signal
Impedance
1.5V p-p max
75 Ohms
The DA1203RM Distribution Amplifier is a state-of-
the-art product with a video bandwidth of 350 MHz,
enabling it to remain transparent to the video signal
passing through it. Each output is individually
buffered and is not affected by other output
loading.
Input Sync Signals
Horizontal, Vertical, & C-Sync
Sync on Green
Impedance
Output Video Signals
Analog Signal
Fall/Rise Time (ns)
Impedance
Output Sync Signals
Composite Sync
Sync on Green
TTL(+/-)
-0.3V
10 k Ohms
1.0V p-p/0.7V p-p
1.4
The DA1203RM offers an internal 90-140/200-
240V power supply and can be rack mounted using
optional accessories hardware ( DA1299RM – rack
ears for single unit and DA1298RM – rack shelf for
two units side-by-side).
75 Ohms
TTL(+/-)
-0.3V
22 Ohms
Impedance
Frequency Compatibility
Horizontal
Vertical
15-200 kHz
47-180 Hz
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DISTRIBUTION AMPLIFIERS
Minimum Video Bandwidth
Typical Video Bandwidth
Cable Equalization
Coupling
350MHz @ -3dB
380MHz @ -3dB
3dB @120MHz
DC
-40dB @10MHz
Cross-talk
Power
Internal Power Supply
Power Consumption
90-140V/200-240V
10 watts max.
Table 3. DA1203RM Electrical
DESCRIPTION OF DA1203RM
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DISTRIBUTION AMPLIFIERS
4.3 VIDEO LEVEL SWITCH
4.1 SYNC POLARITY SWITCH
The Video Level Switch can be set to either the
standard 0.7V output or to 1.0V output. When
the switch is set in the 1.0V output position, this
provides approximately a 35% increase in the
video signal level. This can be used in
installations where cable runs exceed 150 feet.
It is not recommended that this switch be set in
the 1.0V position for shorter cable lengths as the
increased level may reduce the life of CRT
displays if they are over-driven.
The SYNC POLARITY switch is located on the
back panel of the DA1203RM. It has two
switching positions — one designated (+) and
the other (-). By setting the sync polarity switch
to (+), the signal is processed unchanged and
the sync polarity of the output signal matched
the sync polarity of the unit. By setting sync
polarity to (-) the sync polarity of the output is
changed to the opposite of the input.
4.2 SYNC LEVEL SWITCH
4.4 POWER
The SYNC LEVEL switch is also located on the
back panel of the DA1203RM and has two
positions for switching — sync level of 2V and
sync level of 4V. Most often a 4V sync level is
used. This should be considered as default
setting. The 2V setting allows compatibility with
some older equipment that would be overdriven
if a stronger signal were used.
The DA1203RM offers an internal 90-140/200-
240V power supply. A variety of different power
supplies are available for international use.
APPLICATION DIAGRAM
5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DISTRIBUTION AMPLIFIERS
INSTALLING YOUR DISTRIBUTION
AMPLIFIER
OPERATION
7
6
The settings of the DA1203RM Distribution
Amplifier can be adjusted using Input Termination,
Video Level and Sync Level switches as described
in Section no. 4. There are no other adjustments
necessary to operate the unit. The DA1203RM will
operate successfully as long as cables are
attached properly and other technical specifications
are followed.
Step 1.
Step 2.
Step 3.
Make sure that the proper power supply
is being used with the DA1203RM.
Note: The use of an incorrect power
supply can result in equipment damage
not covered by warranty.
Connect the power cord to the
DA1203RM and plug it into the power
outlet. The power indicator LED on the
front panel will light. This indicates that
the unit is operational.
ACCESSORIES
Model No.
8
Description
Connect the high resoluti on RGsB or
RGBS source to the DA1203RM using
coaxial cable with BNC connectors,
making sure that the colors match
correctly. Then connect one or two
monitors or projectors to the output(s) of
the DA1203RM. The monitors or
projectors must be scan-rate compatible
with the source signal - the DA1203RM
does not affect scan rate.
TABLE MOUNT BRACKET
Table Mount Bracket for 2U High, ½
rack units
TM1276
RACK MOUNTING BRACKETS
Rack Mount shelf for two units
Rack Mount shelf for single unit
POWER CABLES
DA1298RM
DA1299RM
9V 500mA Power Supply for US
9V 500mA Power Supply for UK
9V 500mA Power Supply for Australia
9V 500mA Power Supply for Germany
HIGH RESOLUTION 4 BNC to 4 BNC
COAXIAL CABLE
PC5301US
PC5302UK
PC5303AU
PC5304GR
Step 5.
If the image is less than perfect, check
all the connections. Also check the
settings of the switches. The default
settings are Sync Polarity (+), Sync
Level (4V), Video Level (0.7V). Check
all the connections. The unit is very
reliable and seldom will this be the
cause of malfunction. Poor quality
cables may often degrade the
performance of the product. Make sure
that the cables used are coaxial cables
and that all pins are in good condition.
Bulk Cable 4 coaxes (500ft minimum)
3 feet, 4 BNC to 4 BNC coaxial cable
6 feet, 4 BNC to 4 BNC coaxial cable
12 feet, 4 BNC to 4 BNC coaxial cable
25 feet, 4 BNC to 4 BNC coaxial cable
50 feet, 4 BNC to 4 BNC coaxial cable
75 feet, 4 BNC to 4 BNC coaxial cable
100 feet, 4 BNC to 4 BNC coaxial cable
150 feet, 4 BNC to 4 BNC coaxial cable
SUPER HIGH RESOLUTION 4 BNC to
4 BNC COAX
CB4100MR
CB4103MR
CB4106MR
CB4112MR
CB4125MR
CB4150MR
CB4175MR
CB41100MR
CB41150MR
CONGRATULATIONS! YOU ARE DONE.
If you experience any problems, please call
1-800-258-4623 or 1-714-990-2300 for
international calls.
Bulk Cable 4 coaxes (500ft minimum)
6 feet, 4 BNC to 4 BNC coaxial cable
12 feet, 4 BNC to 4 BNC coaxial cable
25 feet, 4 BNC to 4 BNC coaxial cable
50 feet, 4 BNC to 4 BNC coaxial cable
75 feet, 4 BNC to 4 BNC coaxial cable
100 feet, 4 BNC to 4 BNC coaxial cable
150 feet, 4 BNC to 4 BNC coaxial cable
CB4300MR
CB4306MR
CB4312MR
CB4325MR
CB4350MR
CB4375MR
CB43100MR
CB43150MR
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DISTRIBUTION AMPLIFIERS
when the
Video Level
switch is set in level. This can be used in
approximately a 35%
increase in video signal
FREQUENTLY ASKED QUESTIONS
No. Question Answer
9
1
2
3
What is a
Distribution
Amplifier?
A Distribution Amplifier is a
device that allows you to
connect a single video
source to multiple display
devices, such as monitors
or projectors used in
the 1.0V
output
position?
installations where cable
runs exceed 150 feet. It is
not recommended that this
switch be set in the 1.0V
position for shorter cable
lengths as the increased
level may reduce the life of
CRT displays if they are
over-driven.
presentation applications.
When do I use In some cases, you need a
the
DA1203RM?
non-simultaneous
connection of a single C-
Video source or a single S-
Video source to as many
as three different display
or recording devices.
The DA1203RM can pass
RGBS, RGsB, Component
Video (Y, R-Y, B-Y), S-
Video (Y/C), and
TROUBLESHOOTING GUIDE
10
We have carefully tested and have found no
problems in the supplied DA1203RM unit; however,
we would like to offer the following suggestions .
Which signal
formats can be
passed
·
Please make sure that input amplitude levels
are as follows:
through?
Composite Video by using
the appropriate analog
channels (Red, Green,
Blue).
1. Analog signal is less than 1.5V.
2. Sync signal is less than 0.3V.
·
·
Please check the settings of Sync Level, Video
level and Sync Polarity Switches.
4
5
6
When do I use By setting the sync polarity
“+” position of
the Sync
Polarity
switch to (+) the signal is
processed unchanged and
the sync polarity of the
output signal matches the
sync polarity of the
DA1203RM. By setting
sync polarity to (-) the sync
polarity of the output is
changed to the opposite of
the input.
Please make sure that the proper quality of
cables is used. We recommend Altinex made
cables for best results.
switch?
·
If the problem shows up after continuous
usage at higher voltage, higher temperature,
higher humidity, or at other extreme
environmental conditions, please correct those
conditions.
When do I use The SYNC LEVEL switch
the Sync Level has two positions — 2V
switch?
and 4V. Most often a 4V
Sync Level is used. This
should be considered as
default setting. The 2V
setting allows compatibility
with some older equipment
that would be overdriven if
a stronger signal were
being used.
What do I have This provides
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DISTRIBUTION AMPLIFIERS
If your product is out of warranty and needs
ALTINEX POLICY
11
service, contact the Altinex Sales Department
for an RMA (Return Material Authorization).
Products returned without an RMA number may
experience a delay in service. The service
charges will be quoted to you before the actual
repairs are done.
11.1 LIMITED WARRANTY
Altinex warrants that its products and cables are
free from defects in materials under normal use
and service. This warranty is limited to repairing
at company’s factory any part or parts of the
product, which upon company’s examination
shall disclose to be, thus defective. Products
considered defective should be returned to
company with transportation charges pre-paid
within 2 years (90 days for cables) from date of
shipment to the purchaser. The warranty is
expressly instead of all other warranties
expressed or implied. Altinex neither assumes
nor authorizes any other person to assume for it
any other liability in connection with the sale of
the products. This warranty shall not apply to
any product that shall have been repaired or
altered outside of company’s factory in any way
so as, in its judgment, to affect its stability or
reliability, or that has been subject to misuse,
negligence or accident.
11.3 CONTACT INFORMATION
Sales Department
Phone:
Fax:
714-990-2300
714-990-3303
Accounting Department
Phone:
Fax:
714-990-6088
714-990-5778
11.2 RETURN POLICY
It is very important that you receive the product
that you have ordered and that this product
fulfills your need. In the unlikely event that an
Altinex product needs to be returned, please
follow the policies below:
Altinex will accept product returns for a period of
30 days from authorized Altinex dealers.
Products must be returned in an unopened
package.
If product has been opened, the restocking fees
will apply. For the restocking fee amount, please
contact an Altinex Sales Representative.
If product is in your possession for more than 30
days, the restocking fees will apply.
Altinex will not accept any returns on cables or
custom products.
If your product is in warranty and needs service,
contact the Altinex Sales Department for an
RMA (Return Material Authorization). Products
returned without an RMA number may
experience a delay in service.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|