V-MATRIX
MANUAL PART NUMBER: 400-0172-003
VM2143VS
8-IN VIDEO/SYNC INPUT CARD FOR
V-MATRIX™ WITH COVER PLATE
USER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
PRECAUTIONS / SAFETY WARNINGS
1
Please read this manual carefully before using your
VM2143VS. Keep this manual handy for future
reference. These safety instructions are to ensure
the long life of your VM2143VS and to prevent fire
and shock hazard. Please read them carefully and
heed all warnings.
·
Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
1.1 GENERAL
·
Qualified ALTINEX service personnel, or their
authorized representatives must perform all
service.
1.2 INSTALLATION
·
To prevent fire or shock, do not expose this unit
to rain or moisture. Do not place the VM2143VS
in direct sunlight, near heaters or heat radiating
appliances, or near any liquid. Exposure to direct
sunlight, smoke, or steam can harm internal
components.
·
·
Handle the VM2143VS carefully. Dropping or
jarring can damage the card.
Insert the card carefully into the slots of the
V-Matrix™ without bending any edges.
1.3 CLEANING
·
Clean only the connector area with a dry cloth.
Never use strong detergents or solvents, such
as alcohol or thinner. Do not use a wet cloth or
water to clean the card. Do not clean or touch
any component or PCB.
1.4 FCC / CE NOTICE
·
·
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in
a
commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
2
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
ABOUT YOUR VM2143VS
2
PRODUCT DESCRIPTION
4
VM2143VS
8-in V-MATRIX™ Video Input Card
The VM2143VS is an 8-In Video Input Card
designed for use in a V-Matrix™ System and can
handle a wide array of signal formats.
The
VM2143VS can be used for video signals including
Composite Video, S-Video, Component Video,
RGsB, RGBS and RGBHV. Easily accessible
jumpers allow the user to select AC or DC
Couplings, as well as, High or Low input impedance
for each of the 8 individual inputs.
The 8-Input Video Cards provide built-in ground
loop isolation (GLI on Board™) through the use of
differential inputs. This is an extremely important
feature because it protects against hum bars and
other interference caused by ground loops, which
notoriously wreak havoc on large-scale matrix
systems. Both the input and output video cards
provide a bandwidth of 450 MHz @ –3dB, allowing
them to pass extremely high-resolution computer
video signals without signal degradation.
VM2143VS cards are “hot-swappable” with finger
adjustable lock-down screws and secure, positive
engagement card-edge connections into the
V-Matrix™ Enclosure.
TECHNICAL SPECIFICATIONS
FEATURES/
3
VM2143VS
DESCRIPTION
Input
(8)
Input Connectors
Level
8 Female BNC's
1.2Vp-p
75 Ohms, 1%/High Z
Selectable by Jumper
<40dB @ 10MHz
DC (Balanced)
Isolated/Balanced
450MHZ @-3dB
DC/AC
Impedance
Return Loss
Coupling
Type
Bandwidth
Coupling
Selectable by Jumper
Table 1. VM2143VS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
APPLICATION DIAGRAM
Diagram 1 : Connections
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
Diagram 2 : AC Coupled/75 Ohms
Jumper Settings for Video Signal
AC Coupled/75 Ohm Input Impedance
AC/DC COUPLING
JUMPERS
INPUT IMPEDANCE
JUMPERS
P1,P5 OPEN-AC
P1,P5 CLOSE-DC
P20
HIZ
75
75
75
P10,P11 OPEN-AC
P10,P11 CLOSE-DC
P23
P21
HIZ
P6,P7 OPEN-AC
P6,P7 CLOSE-DC
HIZ
P8,P9 OPEN-AC
P8,P9 CLOSE-DC
P22
P24
P27
HIZ
HIZ
HIZ
75
75
P12,P13 OPEN-AC
P12,P13 CLOSE-DC
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
75
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
P25
HIZ
75
P26
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
HIZ
75
Note: In the diagram above, the jumpers are set for 75 ohms input impedance on the following ports:
P20, P23, P21, P22, P24, P27, P25 and P26. (Jumpered pins have dark circles.)
The jumpers on P1, P5, P6, P7, P8, P9, P10, P11, P12, P13 , P14, P15, P16, P17, P18 and P19 are
removed for AC Coupling.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
Diagram 3 : DC Coupled/75 Ohms
Jumper Settings for Video Signal
DC Coupled/75 Ohm Impedance
AC/DC COUPLING
JUMPERS
INPUT IMPEDANCE
JUMPERS
P1,P5 OPEN-AC
P1,P5 CLOSE-DC
P20
HIZ
75
75
75
P10,P11 OPEN-AC
P10,P11 CLOSE-DC
P23
P21
HIZ
HIZ
P6,P7 OPEN-AC
P6,P7 CLOSE-DC
P8,P9 OPEN-AC
P8,P9 CLOSE-DC
P22
P24
HIZ
HIZ
HIZ
75
75
P12,P13 OPEN-AC
P12,P13 CLOSE-DC
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
P27
75
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
P25
HIZ
75
P26
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
HIZ
75
Note: In the diagram, above, the jumpers are set for 75 ohms input impedance on the following ports:
P20, P23, P21, P22, P24, P27, P25 and P26. (Jumpered pins have dark circles.)
The jumpers on P1, P5, P6, P7, P8, P9, P10, P11, P12, P13, P14, P15, P16, P17, P18 and P19 are
installed for DC Coupling.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
Diagram 4 : AC Coupled/High Z
Jumper Settings for Video Signal
AC Coupled/High Impedance
AC/DC COUPLING
JUMPERS
INPUT IMPEDANCE
JUMPERS
P1,P5 OPEN-AC
P1,P5 CLOSE-DC
P20
HIZ
75
75
75
P10,P11 OPEN-AC
P10,P11 CLOSE-DC
P23
P21
HIZ
HIZ
P6,P7 OPEN-AC
P6,P7 CLOSE-DC
P8,P9 OPEN-AC
P8,P9 CLOSE-DC
P22
P24
P27
HIZ
HIZ
HIZ
75
75
P12,P13 OPEN-AC
P12,P13 CLOSE-DC
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
75
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
P25
HIZ
75
P26
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
HIZ
75
Note: In the diagram above, the jumpers are set for High impedance on the following ports:
P20, P23, P21, P22, P24, P27, P25 and P26. (Jumpered pins have dark circles.)
The jumpers on P1, P5, P6, P7, P8, P9, P10, P11, P12, P13, P14, P15, P16, P17, P18 and P19 are
removed for AC Coupling.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
Diagram 5 : DC Coupled/High Z
Jumper Settings for Video Signal
DC Coupled/High Impedance
AC/DC COUPLING
JUMPERS
INPUT IMPEDANCE
JUMPERS
P1,P5 OPEN-AC
P1,P5 CLOSE-DC
P20
HIZ
75
75
75
P10,P11 OPEN-AC
P10,P11 CLOSE-DC
P23
P21
HIZ
HIZ
P6,P7 OPEN-AC
P6,P7 CLOSE-DC
P8,P9 OPEN-AC
P8,P9 CLOSE-DC
P22
P24
HIZ
HIZ
HIZ
75
75
P12,P13 OPEN-AC
P12,P13 CLOSE-DC
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
P27
75
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
P25
HIZ
75
P26
P18,P19 OPEN-AC
P18,P19 CLOSE-DC
HIZ
75
Note: In the diagram above, the jumpers are set for High impedance on the following po rts:
P20, P23, P21, P22, P24, P27, P25 and P26. (Jumpered pins have dark circles.)
The jumpers on P1, P5, P6, P7, P8, P9, P10, P11, P12, P13, P14, P15, P16, P17, P18 and P19 are
installed for DC Coupling.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
Diagram 6 : Internal View
VM2143VS Internal Block Diagram
BNC
INPUT
OUT
1
1
GLI
GLI
GLI
GLI
GLI
GLI
GLI
GLI
HI Z
(SYNC)
LOW Z
(VIDEO)
DC/AC
DC/AC
DC/AC
DC/AC
DC/AC
DC/AC
DC/AC
DC/AC
2
3
4
5
6
7
8
2
3
4
5
6
7
HI Z
(SYNC)
LOW Z
(VIDEO)
HI Z
(SYNC)
LOW Z
(VIDEO)
HI Z
(SYNC)
LOW Z
(VIDEO)
HI Z
(SYNC)
LOW Z
(VIDEO)
HI Z
(SYNC)
LOW Z
(VIDEO)
HI Z
(SYNC)
LOW Z
(VIDEO)
8
HI Z
(SYNC)
LOW Z
(VIDEO)
POWER
9
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
INSTALLING YOUR VM2143VS
6
TROUBLESHOOTING GUIDE
8
Step 1. Decide which type of input video signal
will be used on each input and what the
impedance requirements are of the input
source. Refer to Diagram 2 through
Diagram 5 for jumper settings. Note that
DC Coupling is most commonly used with
DVD players and VCR's and AC Coupling
is most often used with video
conferencing equipment and cameras.
We have carefully tested and have found no
problems in the supplied VM2143VS. However, we
would like to offer suggestions for the following:
8.1 CARD LED'S ARE NOT ON
There are two LED's on the VM2143VS that
indicate power is being supplied to the card.
The LED's are toward the bottom of the card
and facing to the left as viewed from the back of
the enclosure. It may be necessary to remove
other cards to see the LED's.
Step 2. Slide the VM2143VS into one of the slots
on the top half of the V-Matrix™
Enclosure. The top half of the enclosure
is for input cards and the bottom half is for
Cause 1: Enclosure has no power.
Solution: Make sure the V-Matrix enclosure is
plugged in and the power switch is
ON. The LED's on the front of the
enclosure should be ON. If the
enclosure has power and its LED's
are ON, see Cause 2.
output cards.
Make sure that the
VM2143VS fits into place. Secure the
card to the V-Matrix™ by tightening the
retainer screws located on the top and
bottom of each cover plate.
Step 3. Connect a cable from the video source to
the input connector of the VM2143VS.
Cause 2: Card has no power.
Solution: Check the LED's on the card. Both
must be ON for the unit to function
properly. If one or both of the LED's
are OFF, make sure the board is
pushed in all the way. If the LED's
are still not ON, see Cause 3.
Note:
The VM2143VS is an input card for the
V-Matrix™ system. An output card, such
as the VM2144VS, will need to be present
in the output portion of the enclosure in
order to get an output signal.
Cause 3: Card cage slot has a problem.
Solution 1: Test the card in other slots of the
enclosure. If the slot was damaged,
the card may work in other slots. If
other slots work and the LED's light,
the problem is the card cage slot.
The enclosure may require service.
Call ALTINEX at (714) 990-2300. If
the other slots do not work and the
LED's are still not ON, see
Solution 2.
OPERATION
7
Refer to the VM2210BE V-Matrix™ Basic
Enclosure User's Guide (P/N 400-0167-001) for
complete instructions on using the VM2143VS as
part of a V-Matrix™ System
The VM2143VS card will operate successfully as
long as the card is installed properly and other
technical specifications are followed.
Solution 2: Take any other known good card
and verify that the slot used is good
by seeing if the other card’s LED's
light in that slot. If they light, then the
original card may be the source of
the problem. Call ALTINEX at
(714) 990-2300.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
8.2 POOR DISPLAY QUALITY
Cause 4: The card has a problem.
Cause 1: Incompatible devices.
Solution 1: Look at the card and verify that there
is no damage. If there is no damage,
see Solution 2.
Solution: Make sure the video source and the
display
being
connected
are
Solution 2: Verify that all IC’s are seated in their
sockets and that there are no
jumpers missing. If there is still an
error, see Solution 3.
compatible devices.
manufacturer's
Check the
specifications
if
necessary.
If the devices are
compatible, see Cause 2.
Cause 2: Jumpers settings are wrong.
Solution 3: Make sure the display has power
and is turned ON. If there is still no
display, see Cause 4.
Solution: Check the jumper settings per the
diagrams in this manual. If there is
a question as to which position the
jumpers should be in, try each
combination. Note which gives the
best display quality.
Cause 4: Unknown problem.
Solution: Connect the source directly to the
display. If possible, use the same
cables as are being used with the
V-Matrix™ System. If the display
works properly, there may be a
problem with the V-Matrix™ System
or in the setup. Please, call Altinex
at (714) 990-2300.
Cause 3: Inferior cable quality.
Solution: If the image quality is poor, please
make sure that high quality cables
are being used. We recommend
ALTINEX-made cables for best
results.
ALTINEX POLICY
9
8.3 NO DISPLAY
9.1 LIMITED WARRANTY/RETURN POLICY
Cause 1: Cable connections are incorrect.
Please
see
the
Altinex
website
at
Solution: Make sure that cables are properly
connected. First, ensure the correct
input on the VM2143VS is receiving
the input signal from the source.
Next, make sure the selected output
on the output card is connected to
the display. Also, make sure that
the continuity and wiring are good. If
there is still no display, see Cause 2.
www.altinex.com for details on warranty and
return policy.
9.2 CONTACT INFORMATION
ALTINEX, INC
592 Apollo street
Brea, CA 92821 USA
TEL: 714 990-2300
Cause 2: VM2143VS to output card path is
not selected.
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: [email protected]
Solution: Verify the signal is being properly
routed through the V-Matrix™
System. See RS-232 accessible
commands for the VM2210BE
V-Matrix™ Basic Enclosure User's
Guide. If there is still no display, see
Cause 2.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|