V-MATRIX
MANUAL PART NUMBER: 400-0171-001
8-OUT AUDIO OUTPUT CARD FOR
TM
V-MATRIX WITH COVER PLATE
USER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
PRECAUTIONS / SAFETY WARNINGS
1
Please read this manual carefully before using your
VM2142AU. Keep this manual handy for future
reference. These safety instructions are to ensure
the long life of your VM2142AU and to prevent fire
and shock hazard. Please read them carefully and
heed all warnings.
cause
harmful
interference
to
radio
communications. Operation of this equipment
in a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
1.1 GENERAL
·
Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could
void the user’s authority to operate the
equipment.
·
Qualified ALTINEX service personnel, or their
authorized representatives must perform all
service.
1.2 INSTALLATION
·
To prevent fire or shock, do not expose this
unit to rain or moisture. Do not place the
VM2142AU in direct sunlight, near heaters or
heat radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam
can harm internal components.
·
·
Handle the VM2142AU carefully. Dropping or
jarring can damage the card.
Insert the card carefully into the slots of the V-
Matrix™without bending any edges.
1.3 CLEANING
Clean only the connector area with a dry cloth.
·
Never use strong detergents or solvents, such
as alcohol or thinner. Do not use a wet cloth or
water to clean the card. Do not clean or touch
any component or PCB.
1.4 FCC / CE NOTICE
·
·
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable
protection
against
harmful
interference when the equipment is operated
in a commercial environment. This equipment
2
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
ABOUT YOUR VM2142AU
2
TECHNICAL SPECIFICATIONS
3
VM2142AU
8-out V-MATRIX™ Audio Output Card
FEATURES/
DESCRIPTION
VM2142AU – 8-
Output Audio Card
(8)
Output
Connectors
Type
The VM2141AU is an 8-out Audio Output Card
designed for use in a V-Matrix™ enclosure can
handle a wide array of signal formats and
connector types. When installed in a V-Matrix™
Basic Enclosure, these Audio Output cards enable
the connection of eight audio sources. For inputs,
the VM2142AU can be used with the VM2141AU 8-
in Audio Input Card. See the VM2141AU for more
information.
5-pin terminal blocks
Differential (Balanced)
<22 Ohms (drives 600
Ohms directly)
<80dB @ 1kHz
(all channels hostile)
95dB
Impedance
Crosstalk
Signal-to-noise-ratio
Bandwidth
10Hz to 40Hz
Table 1. VM2142AU
The 8-input video cards provide built-in ground loop
isolation (GLI on Board™) through the use of
differential inputs. This is an extremely important
feature because it protects against hum bars and
other interference caused by ground loops, which
notoriously wreak havoc on large-scale matrix
systems. Both the input and output video cards
provide a bandwidth of 350 MHz @ –3dB, allowing
them to pass extremely high-resolution computer
video signals without signal degradation.
All input and output cards are “hot-swappable” with
finger adjustable lock-down screws and secure,
positive engagement card-edge connections.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
PRODUCT DESCRIPTION
4
APPLICATION DIAGRAM
5
Note that card is shown with cover plate
attached.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
TROUBLESHOOTING GUIDE
8
INSTALLING YOUR VM2142AU
6
We have carefully tested and have found no
problems in the supplied VM2142AU; however, we
would like to offer suggestions for the following:
Step 1. Slide the VM2142AU and the VM2141AU
into available slots in the V-Matrix™
Enclosure. Make sure that the cards fit
into place. Secure the cards to the V-
Matrix™ by tightening the retainer screws
located on the top and bottom of each
cover plate.
·
Make sure that power is connected to the
enclosure and also check to see if the
VM2142AU is pushed in all the way.
·
If there is no sound, check the source and
make sure that it is working at an appropriate
volume level and all source connections are
correct.
Step 2. Connect audio cables from the audio
source to the input connector of the
VM2141AU.
Connect
the
output
connectors of the VM2142AU to the audio
·
·
·
Make sure that cables are connected properly.
Also, make sure that the continuity and wiring
are good.
equipment through an audio cable.
OPERATION
7
Make sure that the destination amplifier is
powered. Set the volume of the destination
amplifier to a reasonable level.
The VM2142AU will operate successfully as long
as the card is installed properly and other technical
specifications are followed.
Make sure that the source signal level is high
enough so that the destination amplifier does
not have to provide excessive amplification and
thereby distort the signal.
·
If there is problem with the VM2142AU please
call ALTINEX at (714) 990-2300.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
V-MATRIX
(Return Material Authorization). Products returned
without an RMA number may experience a delay in
service. The service charges will be quoted to you
before the actual repairs are done.
ALTINEX POLICY
9
9.1 LIMITED WARRANTY
ALTINEX warrants that its products and cables are
free from defects in materials under normal use and
service. This warranty is limited to repairing at
company’s factory any part or parts of the product,
which upon company’s examination shall disclose to
be, thus defective. Products considered defective
should be returned to company with transportation
charges pre-paid within 2 years (90 days for cables)
from date of shipment to the purchaser. The
warranty is expressly instead of all other warranties
expressed or implied. ALTINEX neither assumes
nor authorizes any other person to assume for it any
other liability in connection with the sale of the
products. This warranty shall not apply to any
product that shall have been repaired or altered
outside of company’s factory in any way so as, in its
judgment, to affect its stability or reliability, or that
has been subject to misuse, negligence or accident.
9.3 CONTACT INFORMATION
ALTINEX, INC.
592 Apollo Street
Brea, CA 92821 USA
TEL: 714-990-2300
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: [email protected]
FAX: 714-990-3303
9.2 RETURN POLICY
It is very important to ALTINEX that you receive the
products that you have ordered and that this product
fulfills your need. In the unlikely event, that an
ALTINEX product needs to be returned please
follow the policies below:
ALTINEX will accept product returns for a period of
30 days from authorized ALTINEX dealers.
Products must be returned in an unopened
package.
If a product has been opened, the restocking fees
will apply. For the restocking fee amount, please
contact an ALTINEX Sales Representative.
If the product is in your possession for more than 30
days, the restocking fees will apply.
ALTINEX will not accept any returns on cables or
custom products.
If your product is in warranty and needs service,
contact the ALTINEX Sales Department for an RMA
(Return Material Authorization). Products returned
without an RMA number may experience a delay in
service.
If your product is out of warranty and needs service,
contact the ALTINEX Sales Department for an RMA
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|