MULTITASKER®
MANUAL PART NUMBER: 400-0394-007
MT106-103
VIDEO SCALER CARD
USER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
1.4 FCC NOTICE
PRECAUTIONS / SAFETY WARNINGS
1
·
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Please read this manual carefully before using your
MT106-103. Keep this manual handy for future
reference. These safety instructions are to ensure
the long life of your MT106-103 and to prevent fire
and shock hazards. Please read them carefully and
heed all warnings.
1.1 GENERAL
·
This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when the
·
Qualified ALTINEX service personnel or their
authorized representatives must perform all
service.
1.2 INSTALLATION
equipment is operated in
a
commercial
·
To prevent fire or shock, do not expose this unit
to water or moisture. Do not place the
MT106-103 in direct sunlight, near heaters or
heat-radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam can
harm internal components.
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
·
·
·
Handle the MT106-103 carefully. Dropping or
jarring can damage the card.
Do not pull any cables that are attached to the
MT106-103.
·
Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
Insert the card carefully into the slots of the
MultiTasker without bending any edges.
1.3 CLEANING
·
Clean only the connector area with a dry cloth.
Never use strong detergents or solvents, such
as alcohol or thinner. Do not use a wet cloth or
water to clean the card. Do not clean or touch
any component or PCB.
400-0394-007
2
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
ABOUT YOUR MT106-103
2
TECHNICAL SPECIFICATIONS
3
Specifications are subject to change.
MT106-103
Video Scaler Card
FEATURES/
MT106-103
DESCRIPTION
The MT106-103 Scaler converts composite video
(C-Video), S-Video, and component video into a
high-resolution RGBHV/component video output.
GENERAL
Inputs
PC Bypass
15-pin HD female (1)
4-pin Mini DIN (1)
A VGA through SXGA computer signal input can be
switched to the output via a pass-through input.
The C-Video and S-Video inputs accept NTSC and
PAL standards. These inputs are scaled to
VGA through SXGA computer video resolutions or
component video output resolutions 480p, 567p,
720p, or 1080i.
S-Video
Composite Video
Component Video
Output
BNC female (1)
15-pin HD female (1)
15-pin HD female (1)
15-pin HD female (1)
C-Video/S-Video (NTSC/PAL),
Component Video (480i)
VGA through SXGA,
The MT106-103 is controlled using the MultiTasker
command language. Available commands allow
input selection, image control/adjustment including
contrast, brightness, color, tint, and sharpness. In
addition, the MT106-103 incorporates noise
reduction filters and sophisticated 3D comb filtering.
Compatibility
Output Range
480p, 567p, 720p, 1080i
Table 1. MT106-103 General
MECHANICAL
Enclosure Slots
Weight
MT106-103
One
The HelpInside feature allows programmers to
have access to command structures and control of
the MT106-103 from any terminal. This technology
provides easier-than-ever control of the MT106-103
card with simple keyboard commands. No typing of
long keyboard strings is necessary.
1.0 lb (0.45 kg)
Black
Connector Panel
T° Operating
T° Maximum
Humidity
10°C to 35°C
0°C to 50°C
90% non-condensing
40,000 hrs
The MT106-103 also has menu-driven protocol
implemented for easier RS-232 control, eliminating
the need to type lengthy commands for video signal
adjustments.
MTBF (calc.)
Table 2. MT106-103 Mechanical
ELECTRICAL
Input C-Video/S-Video
Analog
MT106-103
1 Vp-p
Impedance
75 ohms
Output Signals
RGB Analog
Impedance
0.7 Vp-p max.
75 ohms
Horiz., Vert. Sync
Power (from enclosure)
+6V
TTL (+/-)
1 A (6.0 W)
50 mA (0.3 W)
-6V
Table 3. MT106-103 Electrical
400-0394-007
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
PRODUCT DESCRIPTION
4
TOP RETAINER SCREW
PC BYPASS INPUT
RGBHV/COMPONENT
VIDEO OUTPUT
S-VIDEO INPUT
COMPOSITE VIDEO INPUT
COMPONENT VIDEO INPUT
(480i)
BOTTOM RETAINER SCREW
400-0394-007
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
APPLICATION DIAGRAMS
DIAGRAM 1: TYPICAL SETUP
5
MT106-103
400-0394-007
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
DIAGRAM 2: INTERNAL VIEW
OUTPUT
INPUT
C-VIDEO
BNC
S-VIDEO
4-PIN
MINI-DIN
COMPUTER/
COMPONENT
VIDEO
SCALER
15-PIN HD
COMPONENT
VIDEO
15-PIN HD
(480i)
PC BYPASS
15-PIN HD
MP
400-0394-007
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
INSTALLING YOUR MT106-103
6
OPERATION
7.1 RS-232 CONTROL
The MT106-103
7
Step 1. Turn off power to the MultiTasker system
and disconnect from AC power.
has
many
advanced
Step 2. Remove a slot cover (MT200-101) from
one of the unused slots. Identify the slot
number and note that it is for RS-232
control.
remote-control capabilities accessible through
standard RS-232 communication. Control may be
accomplished through a computer control system
or any other device capable of sending RS-232
communication.
Step 3. Slide the MT106-103 into the MultiTasker
enclosure in order to connect it to the bus.
Make sure that the card fits into place and
then secure the card by tightening its
retainer screws.
7.1.1 RS-232 INTERFACE
The control commands for the MT106-103 are in
a simple ASCII character format.
1. Square brackets “[ ]” are part of the
command.
2. Use uppercase letters for all commands.
3. Spaces are not legal characters.
Step 4. Make one or more of the following input
video connections:
§ Connect a BNC-type cable from the
video source (camera, VCR, etc.) to
the Video input connector.
The cards in a MultiTasker system are capable
of performing various functions, as well as
providing feedback to the user or control
system. Commands instruct a card to perform
specific actions or request information about the
status of the card. Some commands do both
simultaneously.
§ Connect an S-Video cable from the
S-Video source (DVD, laptop, etc.) to
the S-Video input connector.
§ Use one of the two RCA to 15-pin HD
cables included with the MT106-103 to
connect the component video source
(DVD, satellite, media player, etc.) to
the component video input connector.
A command that instructs the card only to
perform an action will generate feedback of “[ ]”.
The open bracket immediately followed by a
closed bracket indicates the card received a
valid command. If the command requested
information from the card, the feedback
generated by the card is the acknowledgement
of having received a valid command. Invalid
commands generate feedback of “[ERR001]”.
§ Connect the RGBHV video output of a
computer to the PC Bypass input.
Step 5. Connect the output connector of the
MT106-103 to the display device through
a VGA-type (15-pin HD) cable. If the
output of the MT106-103 will be
component video, use the second RCA to
15-pin HD cable included with the
MT106-103 to connect the output of the
Scaler to the input of the display.
Commands ending in “S” will be saved into
memory. Commands not ending in “S” will still
be executed, but will not be restored when the
system is reset or powered off, then on.
7.2 DESCRIPTION OF COMMANDS
Step 6. Restore power to the MultiTasker system.
Each command consists of three parts:
Function, Card ID, and Unit ID.
Step 7. The default input is the Video input port.
Use AVSnap® or other communication
software to change the MT106-103 input.
See the [IN] command in section 7.2 or
section 7.4 for Menu Mode to change the
selection.
[ Function , Card ID , Unit ID ]
400-0394-007
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
Example: [VERC3U2]
VER = Function
BASIC COMMANDS
1. [C]
This command displays the status of the card.
C3
U2
= Card ID or Group ID
= Unit ID (optional for Unit ID 0)
Command Format: [Cn]
Cn = Card ID (n = # from 1 to max slots)
Example:
For Function, see a detailed explanation under
each command description.
The card ID is a unique identifier. It is equal to
the enclosure slot number, or it may be an
assigned value. As the slot number, the value
can range from 1-4 up to 1-to-20 depending on
the enclosure. If the value is assigned, the ID
may be a maximum of 99. Card ID 0 (C0) is
used for the controller and cannot be
reassigned.
There is an MT106-103 card in slot 4. Sending
the command [C4] to the MultiTasker will yield
feedback similar to the following:
Input: Composite Video
Output Resolution: 1024x768
Brightness: 24
Contrast: 40
The group ID is a number representing a group
of cards defined with the [WR] command. When
using the group ID, all cards in the group will
perform the given instruction.
Color: 24
Sharpness: 10
Hue: 0
3D Filter OFF
NR ON
NOTE: In this manual, cards will be referenced
by their ID (C1, C2...C99). Typically, the ID
number will be equivalent to the slot number.
Groups will be referenced by their ID (G1-G8).
Aspect Ratio 4:3
Freeze OFF
Changing the position of a card will significantly
affect the commands recorded on software
definitions or third-party control systems.
If there is no card in slot 4, sending the [C4]
command will not return any feedback.
2. [CnS]
The unit ID has a value from 0 to 9. Unit ID 0
should be used for single unit operation. If the
unit ID is set to zero, each command may be
used without Ui. Use the command [SETU0], as
explained in the MT100-100 User’s Guide.
This command saves the card settings. This
configuration will be restored after the system is
reset or powered-up.
Command Format: [CnS]
Example:
Cn = Card ID (n = # from 1 to max slots)
[VERC3]:
For Unit ID Zero
S
= Save configuration
[VERC3Ui]: For Unit ID other than Zero
Example:
[VERC3]:
Equivalent to [VERC3U0]
The MT106-103 has been set to a resolution of
1024x768 with Composite Video as the active
input. Send [C4S] and receive feedback similar
to the following:
400-0394-007
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
Input: Composite Video
Output Resolution: 1024x768
Brightness: 24
Contrast: 40
5. [VER]
This command displays the software version
and model number for the card.
Command Format: [VERCn]
Cn = Card ID (n = # from 1 to max slots)
Example:
Color: 24
Sharpness: 10
Hue: 0
Send the command [VERC4] to check the
version of the MT106-103 in slot 4. The system
will return the following feedback:
3D Filter OFF
NR ON
Aspect Ratio 4:3
Freeze OFF
[SAVED]
[MT106-103 690-0187-006 C04]
MT106-103 = Model Number
690-0187-006 = Firmware Version
3. [CLR]
C04
= Card ID
Reset the card to its last saved settings.
Command Format: [CLRCn]
Cn = Card ID (n = # from 1 to max slots)
Example:
6. [HELP]
This command displays information available for
the MultiTasker interface commands.
Command Format: [HELPCn]
Cn = Card ID (n = # from 1 to max slots)
Example:
Send the command [CLRC4] to reset the card in
slot 4 to its last saved settings.
4. [FRESET]
In order to display the RS-232 commands
available for the MT106-103 card in slot 4, send
the command [HELPC4]. The commands along
with a brief description will be displayed in the
Terminal Window.
This command clears the card’s memory and
returns the card to its factory default settings.
The factory defaults are as follows:
In =
Res. = 1024x768
3D Filter = Off
Noise Red. = On
Freeze = Off
Aspect Ratio 4:3
S-Video
Brightness = 24
Contrast =
Color =
40
24
FEEDBACK COMMANDS
The next several commands are a function of
both the card and the front panel and are only
available with MultiTasker Front Panel systems
that have the following firmware:
Sharpness = 10
Hue = 00
690-0122-015
690-0123-004
690-0124-018
= Version 015 or later.
= Version 004 or later.
= Version 018 or later.
Command Format: [FRESETCn]
Cn = Card ID (n = # from 1 to max slots)
Example:
Send the command [VER] to the system and the
feedback will include the following:
Send the command [FRESETC4] to reset C4 to
the settings described above. Use the
command [C4S] to save the settings so they will
be recalled upon power-up, reset, or [CLRC4].
690-0122-015 690-0123-004 690-0124-018
Check the last three digits against the numbers
above to determine if the option is available.
400-0394-007
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
7. [FBD]
This command turns feedback delay on or off. It
Example:
The MT106-103 in slot 4 has the S-Video input
selected with an output resolution set to
1024x768. Send the command [?C4] to receive
feedback status similar to the following.
is necessary when installing some newer cards
in older systems. If the system does not receive
all of the feedback from the card, the card may
be communicating too fast. This command will
slow down the card's communication rate.
[(MT106-103C04)(VR690-0187-006C04)
(IN00C04)(RS03C04)(BR24C04)(CN40C04)
(CL24C04)(SH10C04)(HU00C04)(CF0C04)
(NR1C04)(AR1C04)(FZ0C04)]
Command Format: [FBDm]
m = Delay (0= no delay, 1= delay 100mS)
Example:
All status feedback is enclosed in brackets, “[ ]“.
Each data field within the status is enclosed in
parentheses. The first two characters identify
the status type and the last three the card’s ID.
The command [HELPC4] is sent to the card in
slot 4. Some of the HELP file is displayed on the
screen, but most is missing. Send the command
[FBD1] to slow down the rate at which the card
sends feedback to the system.
MT106-103
VR690-0187-007 = Firmware version
= Card model number
IN00
RS03
BR24
CN40
CL24
SH10
HU00
CF
= Active input number
= Active resolution
= Brightness level
= Contrast level
= Color level
= Sharpness setting
= Hue setting
= Comb filter on/off
= Noise reduction
= Aspect ratio
8. [?]
This command will return general information
about the MultiTasker and cards installed in the
unit.
Command Format: [?Ui]
Ui = Unit ID (i = from 0 to 9)
Example:
NR
AR
FZ
= Freeze output image
A MultiTasker with unit ID 1 has a front panel
with part number MT101-101 and contains an
MT103-122, MT103-123, and MT106-103. Send
the command [?U1] and receive the following
feedback:
The IN status line is a 2-digit number
representing inputs 00-03 from the [IN]
command. The RS line reads the resolution
setting 0-9 from the [MODER] command.
[(MT101-101U1)(MT103-122C01)
(MT103-123C02)(MT106-103C04)]
The next 5 lines are the image settings for
brightness, contrast, color, sharpness, and hue.
The last 2 digits in each line show the actual
value.
MT101-101U1 = Panel model number/unit ID
MT103-122C01 = MT103-122 is in slot 1
MT103-123C02 = MT103-123 is in slot 2
MT106-103C04 = MT106-103 is in slot 4
The last 4 lines give the status of the remaining
output image settings. These features are either
on or off and do not have numerical values. A
“1” will be displayed if the feature is on; a “0” will
be displayed if the feature is off.
9. [?C]
This command will display general information
about the card and its status.
Command Format: [?Cn]
Cn = Card ID (n = # from 1 to max slots)
400-0394-007
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
10. [STA1]
This command enables automatic feedback
CARD CONTROL
12. [IN]
from the front panel. The command affects any
card with auto-feedback capability, not just the
MT106-103. The default at power on or reset is
STA0, off. For more details, see the [?Cn]
command definition.
This command selects the input port on the card
to be used as the source. The current image
properties, like brightness and color, do not
change when the input is selected.
Command Format: [INyCn]
Command Format: [STA1]
y = Resolution (y = # from 0 to 3)
0 = S-Video
MT
VR
RS
BR
CN
CL
SH
HU
CF
NR
AR
FZ
Card Model Number
Firmware Revision
Resolution
Brightness
Contrast
Color
Sharpness
Hue
Comb Filter
Noise Reduction
Aspect Ratio
Freeze
1 = Composite Video
2 = PC Bypass
3 = Component Video
Cn = Card ID (n = # from 1 to max slots)
Example:
Send the command [IN0C4] to select the
S-Video input.
13. [INR]
This command selects the input port on the card
to be used as the source and recalls its
previously saved settings.
Example 1:
Command = [MODER4C4]
Feedback = (RS04C04)
Command Format: [INyRCn]
RS = Resolution
04 = 1280x1024
(settings are 00-09)
C04 = Card ID/slot number
y = Resolution (y = # from 0 to 3)
0 = S-Video
1 = Composite Video
2 = PC Bypass
Example 2:
3 = Component Video
Command = [MODEA1C4]
Feedback = (AR0C04)
R = Recall video adjustment settings
Cn = Card ID (n = # from 1 to max slots)
Example:
AR = Aspect Ratio
= Wide 16:9 (1 = 4:3)
C04 = Card ID/slot number
0
Send the command [IN0RC4] to select the
S-Video input and recall the settings saved for
the S-Video input. For example, any changes
made to the brightness, hue etc. that were
saved will be recalled.
11. [STA0]
This command disables automatic feedback
from the card and front panel. The command
affects any card with auto-feedback capability,
not just the MT106-103 card. The default at
power on or reset is STA0, OFF.
Command Format: [STA0]
400-0394-007
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
14. [MODER]
Example:
This command sets the resolution of the video
output.
Send the command [BRIGHTC4] to select the
brightness function on C4. Then use the [+] and
[-] commands to increase or decrease the
brightness level as desired.
Command Format: [MODERxCn]
x
= Resolution (x = # from 0 to 7)
17. [CONTRm]
0
1
2
3
4
5
6
7
8
9
= 640x480 (VGA)
= 480p
This command sets the contrast level to an
absolute value.
= 800x600 (SVGA)
= 1024x768 (XGA)
= 1280x1024 (SXGA)
= 567p
Command Format: [CONTRmCn]
m = Level (m = # from 0 to 48,default=40)
Cn = Card ID (n = # from 1 to max slots)
Example:
= 720p
= 1080i
Send the command [CONTR30C4] to set the
output contrast to 30 on the card in slot 4.
= 1280x768 (WXGA)
= 852x480 (WVGA)
18. [CONTR]
Cn = Card ID (n = # from 1 to max slots)
Example:
This command displays the contrast setting and
makes the contrast function active for use with
the [+] and [-] control commands.
Send the command [MODER4C4] to set the
resolution of the card in slot 4 to 1280x1024.
Command Format: [CONTRCn]
Cn = Card ID (n = # from 1 to max slots)
Example:
15. [BRIGHTm]
This command sets the brightness level to an
absolute value.
Send the command [CONTRC4] to select the
contrast function on C4. Then use the [+] and [-]
commands to increase or decrease the contrast
level as desired.
Command Format: [BRIGHTmCn]
m = Level (m = # from 0 to 48, default=24)
Cn = Card ID (n = # from 1 to max slots)
Example:
19. [COLORm]
This command sets the color level to an
absolute value.
Send the command [BRIGHT12C3] to set the
output brightness to 12 on the card in slot 4.
Command Format: [COLORmCn]
m = Level (m = # from 0 to 48,default=24)
Cn = Card ID (n = # from 1 to max slots)
Example:
16. [BRIGHT]
This command displays the brightness setting
and makes the brightness function active for use
with the [+] and [-] commands.
Command Format: [BRIGHTCn]
Send the command [COLOR12C4] to set the
output color level to 12 on the card in slot 4.
Cn = Card ID (n = # from 1 to max slots)
400-0394-007
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
20. [COLOR]
Command Format: [HUEmCn]
This command displays the color setting and
makes the color function active for use with the
[+] and [-] control commands.
m = Level (m = # from 0 to 48,default=0)
Cn = Card ID (n = # from 1 to max slots)
Example:
Command Format: [COLORCn]
Cn = Card ID (n = # from 1 to max slots)
Example:
Send the command [HUE30C4] to set the output
hue level to 30 on the card in slot 4.
24. [HUE]
Send the command [COLORC4] to select the
color function on C4. Then use the [+] and [-]
commands to increase or decrease the color
level as desired.
This command displays the hue setting and
makes hue the active function for use with the
[+] and [-] controls.
NOTE: The Hue adjustment does not apply to
Component Video.
21. [SHARPm]
This command sets the sharpness level to an
absolute value.
Command Format: [HUECn]
Cn = Card ID (n = # from 1 to max slots)
Ui = Unit ID (i = # from 0 to 9)
Example:
Command Format: [SHARPmCn]
m = Level (m = # from 0 to 48,default=10)
Cn = Card ID (n = # from 1 to max slots)
Example:
Send the command [HUEC4] to select the hue
function on C4. Then use the [+] and [-]
commands to increase or decrease the hue
level as desired.
Send the command [SHARP05C4] to set the
output sharpness to 5 on the card in slot 4.
22. [SHARP]
25. [MODET]
This command displays the sharpness setting
and makes the sharpness function active for use
with the [+] and [-] control commands.
This command is used to turn the 3D Comb
Filter, Y/C Separator either on or off. The filter
should be on when using a VCR input and off
when using other formats.
Command Format: [SHARPCn]
Cn = Card ID (n = # from 1 to max slots)
Example:
Command Format: [MODETpCn]
p
= Filter ON/OFF (p = 0 or 1)
0
1
= OFF (default)
Send the command [SHARPC4] to select the
sharpness function on C4. Then use the [+] and
[-] commands to increase or decrease the
sharpness level as desired.
= ON (VCR Mode)
Cn = Card ID (n = # from 1 to max slots)
Example:
23. [HUEm]
A VCR will be used to play a video tape. Send
the command [MODET1C4] to turn on the 3D
Comb Filter for the MT106-103 in slot 4.
This command sets the hue level to an absolute
value.
NOTE: The Hue adjustment does not apply to
Component Video.
400-0394-007
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
26. [MODEN]
29. [ + ]
This command is used to turn the digital noise
reduction feature on and off.
This command increments a selected property
to be adjusted from the keyboard or front panel.
Command Format: [MODENpCn]
Command Format: [+] or [+k]
[+] = Increment by one
[+k] = Increment by “k”
Example:
p
= Noise Reduction ON/OFF (p = 0 or 1)
0
1
= OFF
= ON
Cn = Card ID (n = # from 1 to max slots)
Select the brightness command for the card in
slot 4. The current brightness level is 10, but it is
not the optimal value. After sending the following
commands, an optimum level of 15 is obtained:
Example:
Send the command [MODEN1C4] to turn on
noise reduction for the MT106-103 in slot 4.
27. [MODEA]
1. [BRIGHTC4]
This command is used to change the aspect
ratio between wide and standard formats.
The current brightness level is 10.
2. [+][+][+][+][+] or [+5]
Command Format: [MODEApCn]
The level is now 15 and no further
adjustments are required.
p
= Aspect Ratio (p = 1 or 2)
1
2
= Wide 16:9
30. [ - ]
= Standard 4:3
This command decrements a selected property
to be adjusted from the keyboard or front panel.
Cn = Card ID (n = # from 1 to max slots)
Example:
Command Format: [-] or [-k]
[-] = Decrement by one
[-k] = Decrement by “k”
Example:
Send the command [MODEA1C4] to set the
aspect ratio to Wide format on the MT106-103 in
slot 4.
28. [FREEZ]
Select the sharpness command for the card in
slot 4. The current sharpness level is 30, but it is
not the optimal value. After sending the following
commands, an optimum level of 25 is obtained:
This command is used to freeze the image
displayed on the display.
Command Format: [FREEZpCn]
p
= Freeze value (p = 0 or 1)
1. [SHARPC4]
0
1
= OFF
= ON
The current sharpness level is 30.
2. [–][–][–][–][–] or [–5]
Cn = Card ID (n = # from 1 to max slots)
Example:
The level is now 25 and no further
adjustments are required.
Send the command [FREEZ1C4] to freeze the
image generated by the MT106-103 in slot 4.
400-0394-007
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
31. [RSI]
ID COMMANDS
This command resets the card IDs in the
system. After sending this command, each card
ID in the system will match the slot number of
the card. If the card is moved to another slot, its
ID number will be the new slot number.
The default card ID is the same as the card slot
number. The next several commands allow the
user to change the card ID to a value other than
the slot number. Once the ID is changed,
moving the card to another slot will not change
the card ID. If a card in slot 4 is set to ID 1, then
moved to slot 10, its ID will remain 1. The [RSI]
command forces each installed card to take its
slot number as its ID number, regardless of the
slot in which it is installed.
Command Format: [RSI]
Example:
Send the command [RSI] to the system with
Unit ID 0. The card in slot 1 will have ID 1, the
card in slot 2 will have ID 2, and so on. If the
card in slot 1 is then moved to slot 4, the card ID
will then be 4.
Some cards require more than one slot in the
MultiTasker system. As an example, some
matrix switcher cards require 4 slots. If 5 of
these cards are installed, they would be
numbered C4, C8, C12, C16, and C20.
Changing the ID allows the user to define the
cards as C1, C2, C3, C4, and C5.
32. [SIDn]
This command sets all the cards installed in the
MultiTasker system to the same card ID. After
sending this command, all cards will be
addressed with the same ID. Use caution when
sending this command to a system with multiple
board types.
Another use for changing the card ID is to be
able to use multiple systems without having to
set each unit to a different unit ID. All systems
may be left as unit ID 0 for ease of
programming. The cards in the first unit may be
numbered 1-10 and in the second unit 11-20.
Command Format: [SIDn]
n
= Card ID (n = # from 1 to 99)
The ID commands work with all MultiTasker
systems. However, front panels that have
firmware releases prior to the following will not
be able to address card IDs greater than the
number of slots in the system:
Example:
Send the command [SID1] to the system. All the
cards in the system now have ID 1. Any
commands that are sent to card ID 1 will be
received and executed by each card.
690-0122-019 = Version 019 or later.
690-0123-005 = Version 005 or later.
690-0124-019 = Version 019 or later.
33. [SIDnCi]
This command sets the card ID of a single card
to a number from 1 to 99.
Send the command [VER] to the system and the
feedback will include the following:
Command Format: [SIDnCi]
n
= Card ID (n = # from 1 to 99)
690-0122-019 690-0123-005 690-0124-019
Ci = Slot Number (i = # from 1 to max slots)
Example:
Check the last three digits against the numbers
above to determine if the card ID commands
can address all 99 card IDs.
Send the command [SID50C10] to set the ID of
the card in slot 10 to an ID of 50.
400-0394-007
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
34. [SID+]
This command sets the ID of all the cards in a
GROUP COMMANDS
Group commands allow several cards with the
same functions to be controlled simultaneously
with a single command. Up to 8 groups (G1-G8)
may be defined. These commands apply to all
cards, not only the MT106-103.
system to their slot number plus the offset value.
Command Format: [SID+n]
n = Offset amount (n = # from 0 to 99)
The maximum card ID is 99, so subtract
the highest slot number from 99 to find
the maximum offset. For example, in an
8-slot enclosure, the maximum offset
would be 91. The slot number (8) plus the
offset (91) equals 99.
36. [WR]
This command adds cards to a group. In
MultiTasker systems with audio and video cards,
the groups are typically as follows:
Group 1 = Video Cards
Example:
Group 2 = Audio Cards
There are two 20-slot enclosures to be
connected together during normal operation.
The first unit will use the default IDs where the
card ID is equal to the slot number. The second
unit will have the same unit ID, but each card ID
will be offset by 20.
Group 3 = Video and Audio Cards
Command Format: [WRCn1Cn2…Gk]
Cn = Card ID (n = slot # from 1 to max slots)
Gk = Group ID (k = # from 1-8)
Example:
Connect the computer to the second unit only
and send [SID+20] to set the ID of all the cards
in the second enclosure to their slot number plus
20. Reconnect both units to the computer.
Add C2, C4, and C6 to G5 by sending the
command [WRC2C4C6G5]. After executing this
command, G5 will consist of C2, C4, and C6.
The cards in the first unit will be referenced as
card IDs 1-20 and the cards in the second unit
will be referenced by card IDs 21-40.
Now add C8 to G5 by sending [WRC8G5]. C8 is
added to G5, and G5 is not overwritten. View
the contents of G5 by sending [RDG5] and
receiving the following feedback:
35. [RSN]
[G5=C2C4C6C8]
This command displays the slot number of a
card with a specified ID number. If more than
one card has the same ID, each slot number will
be displayed.
37. [RMC]
This command removes one or more cards from
a group.
Command Format: [RSNCi]
Ci = Card ID (i = # from 1 to 99)
Example:
Command Format: [RMCn1Cn2…Gk]
Cn = Card ID (n= # from 1 to max slots)
Gk = Group ID (k = # from 1-8)
Example:
The card in slot 4 takes up four slots in the
enclosure. Its ID was set to 1 since it is the first
card installed in the system, reading from left to
right. Send the command [RSNC1] to find the
slot number of this card. The system responds
with the following feedback:
G5 consists of the C2, C4, C6, and C8. Remove
C6 and C8 by sending [RMC6C8G5]. View the
contents of G5 by sending [RDG5] and receiving
the following feedback:
[4]
[G5=C2C4]
400-0394-007
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
38. [RMG]
This command deletes one or all groups.
Feedback Commands
7) [FBD]
8) [?]
Feedback delay
Command Format: [RMGk]
Gk = Group ID (k = # from 1-8, * for all)
Example:
Display system cards
Display card information
Enable auto feedback
Disable auto feedback
9) [?C]
10) [STA1]
11) [STA0]
Card Control
12) [IN]
Remove all cards from G52 by sending [RMG5].
The system will return the following feedback:
[G5=0]
Select input port
Example 2:
13) [INR]
Select input and recall
Remove all cards from all groups, effectively
deleting all groups, by sending [RMG*]. The
system will return the following feedback:
14) [MODER] Set output resolution
15) [BRIGHTm] Set/select brightness
16) [BRIGHT] Display/select brightness
17) [CONTRm] Set/select contrast
G1-G8: EMPTY
39. [RD]
18) [CONTR]
Display/select contrast
This command reads and then displays the
members in a group.
19) [COLORm] Set/select color
Command Format: [RDGk]
Gk = Group ID (k = # from 1-8)
Example:
20) [COLOR] Display/select color
21) [SHARPm] Set/select sharpness
22) [SHARP]
23) [HUEm]
24) [HUE]
Display/select sharpness
Set/select hue
C2, C4, and C6 make up G5. Read the member
data for G5 by sending the command [RDG5].
The system will return feedback as follows:
Display/select hue
25) [MODET] 3D comb filter
26) [MODEN] Noise reduction
27) [MODEA] Aspect ratio
[G5=C2C4C6]
The feedback shows G5 and then the cards that
make up G5. In this case, G5 includes C2, C4,
and C6.
28) [FREEZ]
29) [ + ]
Freeze image
7.3 SUMMARY OF COMMANDS
Basic Commands
Increment property by 1
Decrement property by 1
30) [ - ]
1) [C]
Display card status
Save card settings
Restore saved settings
ID Commands
31) [RSI]
2) [CnS]
3) [CLR]
Reset Card IDs to defaults
Set all Card IDs
32) [SIDn]
33) [SIDnCi]
34) [SID+]
35) [RSN]
4) [FRESET] Reset to factory defaults
Set one Card ID
5) [VER]
Display software version
Set all Card IDs to an offset
Display card slot number
6) [HELP]
Display available commands
400-0394-007
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
Group Commands
7.4.2 USING MENU MODE
36) [WR]
37) [RMC]
38) [RMG]
39) [RD]
Add card(s) to a group
Do NOT press any keys except those relating to
the current menu. If you press the ENTER key
after entering a letter or digit, the original list of
systems will be displayed.
Remove card(s) from group
Delete group
Display group members
1. In order to enter Menu Mode, the system
needs to be connected to a computer
running RS-232 control software.
7.4 MENU MODE
Menu Mode commands allow virtually the same
functionality as programming commands. Unlike
the programming commands, menu commands
prompt the user to select from a list of available
options. The system then responds based upon
selections made by the user.
2. In the Terminal Window, press the ENTER
key on the keyboard.
3. The system checks all MultiTaskers on the
RS-232 bus and displays a list of available
systems.
The menu-driven commands are only available with
MultiTasker systems that have the following front
panel firmware:
Example:
1: U1
2: U2
3: U3
690-0122-015 = Version 015 or later.
690-0123-004 = Version 004 or later.
690-0124-018 = Version 018 or later.
4. Enter the ID number of the desired system.
In the example above, enter a “1” for the
MultiTasker with unit ID 1.
5. The system then interrogates all the cards
available in its enclosure and displays a list
of available cards.
Send the command [VER] to the system and the
feedback will include the following:
690-0122-015 690-0123-004 690-0124-018
Example:
01: MT103-122
02: MT103-123
04: MT106-103
Check the last three digits against the numbers
above to determine if Menu Mode is available.
7.4.1 MENU COMMAND DEFINITIONS
6. Enter the 2-digit ID and a menu for the card
will be displayed. In the example above,
enter “04” for the MT106-103.
Refer to section 7.2 for details on card functions
and examples. Following is a cross-reference of
menu sections versus programming commands.
7. The system will prompt for selections
specific to the selected card.
MENU
COMMAND
[IN], [INR]
8. Read each menu carefully, and continue
selecting keys as prompted.
Input Select
[MODER], [BRIGHTm],
[CONTRm], [COLORm],
[SHARPm], [HUEm],
Setup
NOTE: Menus for data entry have two
prompts: “Key=” and “ESC” (escape). Press the
escape key to return to the previous menu
without making changes.
Output
Properties
[MODEA], [MODET],
[MODEN], [FREEZ],[+], [-]
Version
Status
Help
[VER]
[C]
[HELP]
400-0394-007
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
7.4.3 MENU TYPES
MT106-103 EXPANDED MENUS
1. MAIN MENU
1. INPUT SELECT (0)
The first menu displayed after selecting the
1: INPUT 0 (S-VIDEO)
card is the Main Menu. This menu provides
access to the key functions related to the
card. Press the key representing the menu
item for access and a sub-menu will appear.
2: INPUT 1 (COMPOSITE VIDEO)
3: INPUT 2 (PC BYPASS)
4: INPUT 3 (YCbCr)
2. SUB-MENUS
5: RECALL INPUT 0 (S-VIDEO)
6: RECALL INPUT 1 (COMPOSITE VIDEO)
7: RECALL INPUT 2 (PC BYPASS)
8: RECALL INPUT 3 (YCbCr)
Each menu item will display either a
sub-menu, or a list of options. Press the key
corresponding to the desired choice.
7.4.4 MT106-103 MENUS
Following are the menus available to the
MT106-103. The first menu is the Main Menu
only. The second listing is an expanded view of
the menu items.
2. SETUP
1: OUT RESOLUTION (1024x768)
1: 640x480
The expanded menu contains values that
indicate the current setting or value of a
parameter. The value is usually in parentheses,
or otherwise indicated at the top of a sub-menu.
In some cases, additional comments are
provided for clarification and are not part of the
menu feedback.
2: 480p
3: 800x600
4: 1024x768
5: 1280x1024
6: 576p
MT106-103 MAIN MENU
7: 720p
8: 1080i
1: INPUT SELECT
2: SETUP
9: 1280x768
2: BRIGHTNESS (24)
3: VERSION
4: STATUS
5: HELP
1: +
2: -
3: CONTRAST (40)
1: +
2: -
4: COLOR (24)
1: +
2: -
5: SHARPNESS (10)
1: +
2: -
400-0394-007
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
6: HUE (0)
1. Change Output Resolution
1: +
An MT106-103 is in slot 4. Change the output
resolution to 1280x1024. Start by clicking the
mouse in the Terminal Window. Follow the
keystrokes below:
2: -
7: ASPECT RATIO (4:3)
1: 16:9
Enter
1
04
2
1
5
ESC
ESC
List of systems
Select unit ID 1
Select MT106-103 in slot 4
Select Setup Menu
Select OUT RESOLUTION
Select 1280x1024
8: 3D COMB FILTER (ON)
1: OFF
9: NOISE REDUCTION (ON)
1: OFF
A: FREEZE (OFF)
1: ON
Return to Setup Menu
Return to the Main Menu
3: VERSION
2. Adjust Brightness
This selection displays the model number
and firmware revision, and then redisplays
the Main Menu.
Increase the brightness on the output of the
MT106-103 in slot 4. Starting from the
MT106-103's Main Menu, follow the keystrokes
below:
4: STATUS
This selection displays the card status and
then redisplays the Main Menu.
2
2
1
Select SETUP
Select BRIGHTNESS
Increment by one
5: HELP
This selection displays a list of commands
available for the MT106-103 along with a
brief description.
Repeat until the desired brightness is
achieved.
ESC
ESC
Return to SETUP
Return to the Main Menu
ESC
This selection returns you to the parent
menu with the listing of all cards.
3. Display Card Status
7.4.5 MENU MODE EXAMPLES
Display the status of the MT106-103 in slot 4
All Menu Mode examples assume an
starting from its Main Menu.
MT106-103 is installed in slot 4 of unit ID 1.
4
Display card status
NOTE: The communication software you use
may echo each character as it is typed
when entering numeric values (not
selecting menu items). For example,
entering a value of 03 may appear as
0033 on the screen.
NOTE: The Main Menu will be redisplayed
after the status is displayed.
400-0394-007
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTITASKER
TROUBLESHOOTING GUIDE
8
ALTINEX POLICIES
9
We have carefully tested and have found no
problems in the supplied MT106-103. However, we
would like to offer suggestions for the following:
9.1 LIMITED WARRANTY/RETURN POLICIES
Please see the ALTINEX website at
www.altinex.com for details on warranty and
return policies.
8.1 NO DISPLAY
Cause 1: The source has a problem.
9.2 CONTACT INFORMATION
ALTINEX, Inc.
Solution: Check the source and make sure
that there is a signal present and all
source connections are correct. If
the source is working and there is
still no display, see Cause 2.
592 Apollo Street
Brea, CA 92821 USA
TEL: 714 990-2300
Cause 2: The card output is not selected.
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: [email protected]
Solution: Select the card output. See RS-232
accessible commands in Section 7.
If no display is present, see
Cause 3.
Cause 3: Cable connections are incorrect.
Solution: Make sure that cables are properly
connected. Also, make sure that the
continuity and wiring are good. If
there is still no display present, see
Cause 4.
Cause 4: The display has a problem.
Solution: Make sure the display is powered
and is turned on. If there is still no
display, please call ALTINEX at
(714) 990-2300.
400-0394-007
21
Download from Www.Somanuals.com. All Manuals Search And Download.
|