Altec Lansing Speaker ATP3 User Manual

Specifications  
One Year Limited Warranty  
Altec Lansing Technologies, Inc. warrants  
to the end user that all of its computer  
speaker systems are free from defects in  
material and workmanship in the course  
of normal and reasonable use for a term of  
one year from the date of purchase.  
Overall  
Total Audio Power 30 Watts RMS  
Input Sensitivity  
output  
300 mV for full  
User’s Guide  
Computer Speaker System  
Input Impedance  
>10 kOhms  
This warranty is the exclusive and only  
warranty in effect relative to Altec  
Lansing computer speaker systems and  
any other warranties, either expressed  
or implied, are invalid. Neither Altec  
Lansing Technologies, Inc. nor any  
authorized Altec Lansing Technologies,  
Inc. reseller is responsible for any  
incidental damages incurred in the use of  
the speakers. (This limitation of  
incidental or consequential damage is not  
applicable where prohibited.)  
Frequency Response 45 Hz – 18 kHz  
Satellites  
Drivers (per satelllites) Two 28 mm  
micro drivers  
One 3” mid-bass  
Audio Power  
satellite  
6 Watts per  
(12 Watts total)  
RMS @ 1% THD  
S/N Ratio  
>70 dB  
Altec Lansing Technologies, Inc.’s  
obligation under this warranty does not  
apply to any defect, malfunction or  
failure as a result of misuse, abuse,  
improper installation, use with faulty or  
improper equipment or the use of the  
computer speaker systems with any  
equipment for which they were not  
intended.  
Subwoofer  
Driver  
throw  
One 6.5” long  
Audio Power  
18 Watts  
RMS @ 1% THD  
Crossover Frequency 150 Hz  
The terms of this warranty apply only to  
computer speaker systems when such  
speakers are returned to the respective  
authorized Altec Lansing Technologies,  
Inc. reseller where they were purchased.  
Power Requirements  
USA/CANADA  
AC  
120 Volts 60 Hz  
Europe/United Kingdom and  
various Asian countries  
50 Hz AC  
Under the terms of this warranty the  
original consumer purchaser has certain  
legal rights and may have other rights  
which vary worldwide.  
230 Volts  
ETL/cETL/CE approved  
© 2000 Altec Lansing Technologies, Inc.,  
Milford, PA 18337  
ATP3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
on and counter-clockwise to turn power  
off.  
Description  
Figure 1  
The ATP3 is an amplified speaker system  
featuring a subwoofer for extended low  
frequency response. The system is  
especially designed for multimedia  
computer applications. The unit is  
comprised of a subwoofer and two  
satellite speakers, and features separate  
VOLUME, BASS and TREBLE controls. The  
satellite speakers are uniquely designed  
to provide full tweeter and mid-bass  
response in a slim profile housing that  
complements flat panel as well as  
standard monitors. The satellite speakers  
are magnetically shielded and can be  
placed close to a monitor without  
distorting images.  
Volume Control: Turn the Volume  
Control clockwise to increase overall  
volume level. Turn counter-clockwise to  
decrease volume.  
Bass Control: The Bass Control adjusts  
the volume level of the low subwoofer  
frequencies. To increase Bass, turn the  
control clockwise. To decrease Bass, turn  
the control counter-clockwise.  
Treble Control: Treble frequencies are  
emitted from the satellite speakers. To  
increase treble (high frequencies), turn  
the control clockwise. To decrease treble,  
turn the control counter-clockwise.  
Placement of the Speakers and  
Subwoofer  
Notice: To avoid a “pop” sound when  
pulling out the power plug from the AC  
outlet or turning off power from a master  
switch, first turn off the ATP3 with the  
ON/OFF switch.  
All stereo information is heard from the  
satellite speakers. The satellite speakers  
are magnetically shielded and can be  
placed close to the monitor without  
distorting images. Best stereo effect is  
obtained by placing the satellite speakers  
as far apart as practical. The subwoofer  
contains no stereo information and sound  
is non-directional. As a result, the  
subwoofer does not have to be placed in  
any particular relation to the satellite  
speakers. Placing the subwoofer on the  
floor close to a wall or corner of a room  
provides maximum bass efficiency. The  
subwoofer is not magnetically shielded  
and should not be placed close to the  
monitor  
Use of Controls (See Figure  
1)  
Power On/Off: The ON/OFF switch is  
part of the volume control. Turn the  
volume control clockwise to turn power  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ATP3 Setup Instructions  
Set Up Instructions  
(See Figure 2)  
Figure 2  
Do not insert the AC power  
plug into the wall outlet  
until all connections are  
made.  
LEFT  
RIGHT  
INPUT  
Make connections as shown in  
Figure 1.  
1) Connect the LEFT SATELLITE  
SPEAKER to the SUBWOOFER.  
Connect BROWN PLUG from the  
LEFTSATELLITESPEAKER into  
the jack on the subwoofer  
marked LEFT.  
2)  
Connect the RIGHT  
SATELLITE SPEAKER to the  
SUBWOOFER. Plug the speaker  
wire with the ORANGE  
connector  
into  
the  
corresponding jack on the back  
of the subwoofer marked RIGHT.  
Note that this connector has an  
arrow on it. This arrow should  
face up as shown in Figure 1.  
LEFT RIGHT INPUT  
3) Connect the SUBWOOFER to  
the computer. The lime color-  
coded wire connects the input on  
the subwoofer to the audio output  
on your computer.  
ORANGE  
LIME  
BROWN  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3Com Network Router NETBuilder II User Manual
3G Green Green Globe Dishwasher SDEC1000A User Manual
Accusplit Heart Rate Monitor 605XE User Manual
AEG Washer L 87480 FL User Manual
AKG Acoustics Drums Micing User Manual
Altec Lansing Portable Speaker 515 G User Manual
Avocent Computer Monitor 416 User Manual
Axis Communications Security Camera AXIS Q1931 E User Manual
Banner American Products Work Light 150 3M User Manual
Beckett Water Gardening Outdoor Fountain CPK302 User Manual