CONTENTS
1. PRODUCT GENERAL INFORMATION..……………………………………………..….2
1.1. Product Description…………………………………………………………………………………….2
1.2. Product Feature…………………………………………...……………………………………………2
1.3. Product Application………………………………………………………….……………………………..2
2. PRODUCT GENERAL………………………………………………………………….….3
2.1. General Specifications………………………….………………..…………………………..… 3
2.2. LED Indicator………………………………………………………..…………..….………………3
2.3. Interface………………………………………………………….…….………………………..…..3
3. PRODUCT HARDWARE SPECIFICATION……………………….………………….….3
3.1. RF Specification…………………………………………………….………….….…………………..….3
3.1.1. General……………………………………………………….………………..………………..3
3.1.2. Transmitter…………………………………………………….…………..……………………3
3.1.3. Receiver…………………………………………………………………..……………………4
3.1.4. Antenna Type………………………………………………….…………..…………………...4
3.1.5. Typical Operating Range………………………………………….………..…………………4
3.2. H/W Specification………………………………………………………….…………………………....4
3.2.1. MAC Controller.…………………………………………………….……..……………………4
3.2.2. Memory.……………………………………………………………….…..…………………….4
3.2.3. Power……………………………………………………………………....……………………4
4. PRODUCT SOFTWARE SPECIFICATION………………………………….……...……4
4.1. Driver…………………………….……………………………...……………..……………………..…..4
4.2. Configuration Utility………………..…………………………….………..………………………..….4
5. PRODUCT COMPLIANCE………………………………………………………….……..5
6. OPERATING CONDITION……………………………………………………..……..5
6.1. Drop and Vibration test……………………………….……………………………...……….5
6.1.1. Anti-Static Voltage……………………………………………………………………..………..5
6.1.2. Vibration Test………………………………………………………..…………….….………..5
6.1.3. Package Drop Test……………………………………………………………….…..…………5
6.2. Operation Environment ……………………………………………………………………...……….…5
6.2.1. Temperature Range………………………………………………………………….…………5
6.2.2. Reliability Test…………………………………………………….…………….5
6.2.3. Humidity…….…………………………………………..…………………………………….….5
7. INSTALLATION AND CONFIGURATION……………………..………………..……..6
7.1. Installation………….……………………………….……………………………...……….6
7.2. Configuration……………………………………………………………………………...……….…6
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2. PRODUCT GENERAL
2.1. General Specifications
Standards:
IEEE802.11b Compliant
PC Card standard Ver 7.0
Data Rate:
Security:
22Mbps / 11Mbps / 5.5 Mbps / 2Mbps / 1 Mbps auto fallback
64/128/256 bit Wired Equivalent Privacy (WEP)
128 x 54 x 5.0 mm (Non-detachable card)
Dimension:
2.2. LED Indicators
Power/Status
Unlighted: Power Off
Red color LED steady On: Power on
Unlighted: no activity
RF TX/RX
Green color LED blinking: TX/RX activity
2.3. Interface
CARD BUS
PC Card standard Ver 7.0
3. PRODUCT HARDWARE SPECIFICATIONS
3.1. RF Specification
3.1.1 General
Emission Type
Direct Sequence Spread Spectrum (DSSS)
2400MHz – 2497 MHz – Japan Band
2400MHz – 2472MHz – North America
2400MHz – 2483.5MHz – Europe
2446.5MHz – 2483.5MHz – France
11 Channels (US, Canada)
RF Frequency
Operating Channel
13 Channels (Europe)
14 Channels (Japan)
Radio Chipset:
RFMD
Media Access Protocol
CSMA/CA (Collision Avoidance) with ACK
3.1.2 Transmitter
RF Output Power
15 dBm
Frequency Stability
Data modulation type
Data modulation speed
Within + 25 ppm
BPSK / QPSK / CCK / PBCC
22/11/5.5/2/1 Mbps with auto fallback
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.3 Receiver
Sensitivity
-80 dBm (Typically @25℃+5℃)
3.1.4 Antenna Type
Antenna Type
Built in diversity patch antenna
2 dBi max.
Antenna Gain
3.1.5. Typical Operation Range
22Mbps
11Mbps
5.5Mbps
2Mbps
100M
150M
250M
300M
350M
1Mbps
3.2 Hardware Specification
3.2.1 MAC controller
TI ACX100
3.2.2 Memory
8Kbit EEPROM
3.2.3 Power
Power Voltage
3.3 or 5 Volt + 5%
Power Consumption
650 mA by TX (Max)
350mA by RX
4. PRODUCT SOFTWARE SPECIFICATION
4.1. Driver
NDIS4.0 LAN driver for Win98
NDIS5.0 LAN driver for Win2000, Win ME
NDIS5.1 LAN driver for Win XP
4.2. Configuration Utility
Configuration Utility software program for Win98, Win2000, WinME and WinXP.
Configurable Parameters
Description
Networking Type
Infrastructure / Ad-Hoc
Channel
ESSID
Rx Rate
TX Rate
WEP
Channel number setting (14 channels available)
ESSID setting
Current Receiving data rate
Current Transmitting rate
Disable, 64 bit, 128 bit and 256 bit
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Link Quality
Receiving AP link quality on infrastructure networking mode
Receiving AP signal strength on infrastructure networking mode
Signal Strength
5. REGULATION COMPLIANCE
Compliant with
FCC Part 15 Class B and C
ETSI EN 300 328-2 and ETSI EN 301 489-1, -17, EN60950, CE-Mark
Telec (Japan, Customized)
WiFi Compliant
6. Environmental Requirement
6.1. Drop and Vibration
6.1.1. Anti-Static Voltage
Static voltage tests by 4 kV in card frame should not cause system fail
6.1.2. Vibration Test
The vibration test is under the frequency and amplitude 10-25 Hz 1mm in vertical and horizontal direction by 30
minutes that should not cause any damage on product.
6.1.3. Package Drop Test
Dropping the package from the height of 50cm for each of the six(6) faces onto the hard-wood floor should not cause
any damage on product.
6.2. Operation Environment
6.2.1. Temperature Range
Operating:
Storage:
-0℃ - +55℃ (Except RF output power and sensitivity)
-20℃ - +70℃
6.2.2. Reliability Test
One cycle of reliability test is keeping at -30℃ by 2 hours, switching temperature up to +60℃ within one hour , and
testing at +60℃ by 2 hours, and switching temperature to -30℃ within one hour. Three cycle should be tested and
without any product fail.
6.2.3. Humidity
Operating:
0% to 70%
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
0% to 95% Non-condensing
7. INSTALLATION AND CONFIGURATION
7.1. Installation
1. Start the computer
2. Insert the PC CARD to the slot of computer
3. Run ”E:\ Wlan PC Card\Utility\Setup.exe”. Windows will automatically start Installshield Wizard and then insert the PC
CARD into the slot of the computer.
4. Select “PC Card/PCI Card”
5. Click “Install “ Button.
6. Click “Next” button.
7. Click “Finish” button to restart computer.
7.2. Configuration
1. Please insert your Wireless Card into PCMCIA slot.
2. Click “
” icon in the right hand corner of the screen.
3. The Utility configuration link information page should appear on your monitor. It will show you the Wireless card status.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Click the “Configuration”. The Configuration page will appear. Enter your wireless network’s SSID, select the BSS Type,
suggest you use default “Infrastructure”, Then click “Apply”.
5. Click the “Security”. From the security setting screen, you can set the Wired
Equivalent Privacy (WEP) encryption by checking the “Data Encryption”. Then change the
“Key Format” to “ASC II”. It is easier than using the “HEX” format. Enter a set of
random combination of number and alphabet in the “Network Key” frame. Then click
“Apply”. Follow the appearing dialogue to adjust the length of the entering “Network Key”
based on the “Key Length”. Then click “Apply” until no dialogue appears.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
If you have an access point and enable the security function, please follow the access point
“Network Key”.
6.Click “SiteSurvey”. Select one of SSID from “Available Network” Block. Then click “Connect” button to enter Profile
page.
7. You can set all parameters or click “OK” to back to previous page. If you click “OK” directly, then you finish the connect
action.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8.Click “About”. It will show you Software Version of this Wireless Lan PC Card.
Notice : Our company reserves the right to change specifications detailed in this document at any time
without notice, and assumes no responsibility for any errors within this document.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if t not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by during the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
ꢀ
ꢀ
ꢀ
ꢀ
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 2.5cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Caution: This device includes a module which can emit RF energy. For compliance with FCC exposure rule, the user has to keep at
least 2.5cm separation distance between the radiator and the body of the user.
Printed in Taiwan
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|