Washer-Extractors
Cabinet Hardmount
A-Series Microcomputer for OPL Models
2 Speed and Variable-Speed
1 2
3 4
5 6
CHM1766C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F232224R1
May 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Identification ...........................................................................
2
Table of
Contents
Safety Information..............................................................................
Operator Safety.....................................................................................
3
Programming ......................................................................................
7
Test Cycle............................................................................................. 16
Cycles 1 - 24 .................................................................................... 19
Cycles 31 - 46 .................................................................................. 21
© Copyright 2008, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F232225
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Identification
Information in this manual is applicable to these
models:
HC80ANV
SC40AN2
SC40ANV
SC60ANV
SC60AN2
SC60ANF
SC80ANV
UC125ANV
UC20AN2
UC30AN2
UC40AN2
UC40ANV
UC60AN2
UC60ANF
UC60ANV
UC80ANV
SC125ANV
SC20AN2
SC30AN2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232224
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
Explanation of Safety Messages
Important Safety Instructions
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
DANGER
1. Read all instructions before using the washer.
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION MANUAL for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, dry-
cleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas is
flammable; do not smoke or use an open flame
during this time.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
IMPORTANT: The word “NOTE” is used to
communicate installation, operation, maintenance
or servicing information that is important but not
hazard related.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
3
Safety Information
9. Do not install or store the washer where it will be
exposed to water and/or weather.
20. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
10. Do not tamper with the controls.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT
bypass the loading door switch by permitting the
washer to operate with the loading door open.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
connect the washer to the electrical power source.
13. Use washer only for its intended purpose,
washing textiles.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
16. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
flammable chemicals, thinner, etc. or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a qualified
service person.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
4
Safety Information
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
SW025
WARNING
damage, and may void the warranty.
SW004
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance
are provided. Never allow the inspection and
maintenance space to be blocked.
the pipe can be touched.
SW014
WARNING
Safety Decals
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
damage.
W703
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
5
Safety Information
Do not bypass any safety devices in the machine.
Operator Safety
WARNING
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
SW012
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
damage.
SW039
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
6
Programming
NOTE: The machines are factory-programmed
with basic cycles to make the units operational
without programming at the installation.
NOTE: Changing degrees “FAr” or “CEL” only
has an effect if the control has a temperature probe
connected and/or heat capability.
2. Press START keypad.
Entering Program Mode
3. Select “HEAt” or “noHt”. Change the selection
1. Open machine lid.
by pressing the ∧ or ∨ keypad.
2. Locate Program/Run switch on the computer
board. This is accessed through a cutout in the
metal control unit cover. This switch protrudes
from the rear of the electronic control unit cover.
NOTE: If set for “HEAt”, the control has heat
capability enabled. The washer-extractor MUST
have electric or steam heat, and a temperature
probe. If display shows “noHt”, or if the message
“HEAt” or “noHt” does NOT display, the control
does NOT have heat capability.
3. Flip switch to the left (as seen from the front of
machine) to enter PROGRAM Mode.
4. Display will show temperature.
4. Press START keypad to continue to the next step.
5. Select “AFIL” or “SUP5”. For “SUP5”, a fifth or
sixth supply can be programmed in a cycle step.
“AFIL” allows auxiliary fills to be programmed
to low, medium or high water level in a cycle
step.
Cycle and Error Count
The control logs cycle count (total of all cycles
completed).
1. To read, enter PROGRAM Mode.
6. Press START keypad.
2. Press START (Enter) keypad. Display will show
the cycle count.
7. Select “tFIL” or “ntFL.” “tFIL” allows a
temperature controlled fill to be programmed for
any segment. Select “ntFL” to disable the
feature.
3. Press START (Enter) keypad. Display will show
certain error conditions that may have been
recorded by the control.
WARNING
4. Read the information when consulting technical
assistance as needed.
To avoid personal injury, recommended
inlet water temperature should be no
higher than 125° Fahrenheit (51° Celsius).
5. Step through the error log by pressing START
keypad repeatedly until display reverts to normal
PROGRAM Mode (“0000” or a temperature).
W709
8. Press START keypad.
Setup Mode
9. Select “COOL” or “noCL.” “COOL” enables an
automatic cooldown feature allowing cold water
to flush into wash before a drain if temperature is
140°F (60°C) or above. Select “noCL” to disable
feature.
NOTE: In SETUP Mode, certain machine
functions can be configured. The settings in this
mode are related to how the machine is equipped
from the factory. Usually, these settings would not
be changed.
10. Press START keypad.
11. Select “bEEP” (control sounds beeper during
Add Bleach [Supply 2]) or “nobP” (control does
NOT sound beeper during Add Bleach [Supply
2]). Change selection by pressing ∧ or ∨ keypad.
NOTE: Enter SETUP Mode through the Program
Mode.
1. Press (6) keypad. Display will show “FAr” or
“CEL”.
12. Press START keypad.
NOTE: This selects whether temperatures display
in degrees Fahrenheit (F) or Celsius (C), if control
is equipped with a temperature sensor. Change
selection by pressing ∧ or ∨ keypad.
13. Select “Adv” or “noAd”. “Adv” enables the
Rapid Advance feature. Select “noAd” to disable
the feature.
14. Press START keypad.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
7
Programming
NOTE: While cycle is running, pressing the START
keypad shows the temperature. Pressing the
START keypad a second time displays the cycle.
Pressing the START keypad a third time returns
display to time remaining.
Programming Cycle Segments
The machine has 30 wash cycles available. 26 wash
cycles are pre-programmed. 4 cycles are available for
custom programming. All wash cycles may be edited
as follows.
1. Enter PROGRAM Mode. Refer to Entering
Program Mode section.
2. Press “∧” keypad to enter PROGRAM Mode.
3. Press the cycle number of the cycle to be edited.
Refer to Table 1.
4. Press the START keypad to move into the menu
19
16 17 18
1
2
5
15
14
1 2
3 4
5 6
6
13
7
12
11
10
8
9
3
4
CHM1766C
1
2
3
4
5
6
7
8
9
Cycle Keypad “1”
Cycle Keypad “3”
Cycle Keypad “5”
Rapid Advance/Up “∧” Edit
Cycle Keypad “2”
Cycle Keypad “4”
Cycle Keypad “6”
Stop/Down “∨” Edit
START Keypad
11
12
13
14
15
16
Door Open LED
Spin Cycle LED
Rinse Cycle LED
Add Bleach LED
Wash Cycle LED
Out-of-Balance Indicator Dot
(Variable-speed only)
High Water Level Indicator Dot
Medium Water Level Indicator Dot
Low Water Level Indicator Dot
17
18
19
10
CLEAN FILTER Indicator LED
Figure 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232224
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Cycle
Number
Cycle Name
1
Permanent Press Light Soil
Cotton Terrycloth Light Soil
Permanent Press Medium Soil
Cotton Terrycloth Medium Soil
Permanent Press Heavy Soil
Cotton Terrycloth Heavy Soil
Table Napery Blends Colors
Table Napery Blends Whites
VISA Table Napery Colors
VISA Table Napery Whites
Rags Heavy Soil
2
3
4
5
6
11
12
13
14
15
16
21
22
23
24
25
26
31
32
33
34
35
36
41
42
43
44
45
46
Reclaim
Personals with Bleach
Personals No Bleach
Delicates Spreads Cold Water
Delicates Spreads Warm Water
Custom #1
Custom #2
Normal 90•C (Pre Wash)
Normal 90•C
Normal 60•C (Pre Wash)
Normal 60•C
Normal 40•C (Pre Wash)
Custom #3
Permanent Press 90•C (Pre Wash)
Permanent Press 90•C
Permanent Press 60•C (Pre Wash)
Permanent Press 60•C
Fine 40•C
Custom #4
Table 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
9
Programming
Options for Each Segment
Cycle Steps Available
(NOTE: WASH, ADD BLEACH, RINSE
and SPIN LEDs light ONLY when a
cycle formula is in operation.)
Display
Setting Options for Cycle Steps
Wash 1-5 (displayed as “USH1”-“USH5”)
Time for Agitation (excludes fill, drain,
spin and heat)
AG1
AG2
AG3
AG4
0 or 2-30 minutes in agitation step (increases/decreases in
each agitation segment
Fill valves (temperature)
CFIL
HFIL
bFIL
AFIL
LO
Cold, Hot or Both (warm) water fills or Auxiliary fill
Low, Medium or High water level
Fill water level control
Supply
nEd
HI
SUP0
SUP1
SUP2
SUP3
SUP4
SUP5
SUP6
SUP7
operation of each supply selection)
o
o
Heat (Models with heat or heat capability) HEAt
noHt
00F (no heat for segment) or 75 F to 200 F
o
o
00C (no heat for segment) or 25 C to 93 C
Drain (Final segment drains in stop
routine if No Drain is programmed)
drAI
nodr
SPIn
tInE
Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain segment )
Spin time
00 for No Spin or 60-240 seconds (increases/decreases in
one-second increments)
Rinse 1-5 (displayed as “rIn1”-“rIn5”)
Time for Agitation (excludes fill, drain,
spin and heat)
AG1
0 or 2-30 minutes in agitation step (increases/decreases in
each agitation segment
AG2
AG3
AG4
CFIL
HFIL
bFIL
AFIL
LO
Fill valves (temperature)
Fill water level control
Cold, Hot or Both (warm) water fills or Auxiliary fill
Low, Medium or High water level
nEd
HI
Table 2 (continued)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232224
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Table 2 (continued)
Supply
SUP0
SUP1
SUP2
SUP3
SUP4
SUP5
SUP6
SUP7
operation of each supply selection)
o
o
Heat (Models with heat or heat capability) HEAt
noHt
00F (no heat for segment) or 75 F to 200 F
o
o
00C (no heat for segment) or 25 C to 93 C
Drain (Final segment drains in stop
routine if No Drain is programmed)
drAI
nodr
SPIn
Drain or No Drain (if No Drain programmed, will skip spin
segment associated with Drain segment )
Spin time
00 for No Spin or 60-240 seconds (increases/decreases in
one-second increments)
Rinse 6 (displayed as “rIn6”)
Time for Agitation (excludes fill, drain,
spin and heat)
AG1
AG2
AG3
AG4
CFIL
HFIL
bFIL
AFIL
LO
0 or 2-30 minutes in agitation step (increases/decreases in
each agitation segment
Fill valves (temperature)
Cold, Hot or Both (warm) water fills or Auxiliary fill
Low, Medium or High water level
Fill water level control
Supply
nEd
HI
SUP0
SUP1
SUP2
SUP3
SUP4
SUP5
SUP6
SUP7
operation of each supply selection)
o
o
Heat (Models with heat or heat capability) HEAt
noHt
00F (no heat for segment) or 75 F to 200 F
o
o
00C (no heat for segment) or 25 C to 93 C
Drain (Final segment drains in stop
routine if No Drain is programmed)
drAI
nodr
Spin Speed (displayed as SPn1-SPn3)
Spin time
SPIn
1-10 minutes (increases/decreases in one-minute
increments)
Table 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232224
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
NOTE: If the wash load becomes out of balance,
the machine will attempt to balance the load. After
three failed attempts the display will light the
leftmost digit and a lower spin will be used to
1
1
3
5
2
4
6
CHM512R
1
Out-of-Balance LED
Figure 2
Supply Programmed
External Chemical Supply Signal
Compartment Flushed
None
SUP0
SUP1
SUP2
SUP3
SUP4
SUP5
SUP6
SUP7
None
Supply 1
Supply 2**
Supply 3
Supply 4
Supply 5***
Supply 6***
Supply 7
Compartment 1*
Compartment 2
Compartment 3
No compartment Flush*
No compartment Flush*
No compartment Flush*
Compartment 3
Table 3
*NOTE: Only supply 2 (SUP2) and supply 3
(SUP3) have independent water valves to flush
their respective compartment. Compartment 1 will
flush whenever machine is filling with water.
External chemical supply signals and any related
flush valves will activate approximately 15 seconds
after machine begins to fill with water. If
programmed water level is reached prior to 15
seconds, no chemical supply signal will be
activated.
**NOTE: ADD BLEACH LED lights if Supply 2 is
the only supply programmed. If set up for
"bEEP"(refer to SETUP Mode section), buzzer will
sound on and off for the first eight seconds. The
Supply 2 and ADD BLEACH LED remain on for
45 seconds or until the fill is complete, whichever
comes first.
***NOTE: Selecting "AFIL" (auxiliary fill) in
SETUP Mode will remove supply 5 and supply 6 as
optional supply signals.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
12
Programming
10. Press the ∧ or ∨ keypad to alter the selection, or
To Edit an Entire Wash Cycle
Formula
the START keypad to continue.
NOTE: Auxiliary Fill (“AFIL”) possible only if
configured for “AFIL” in SETUP Mode. If
configured, auxiliary fills can be programmed to
low, medium or high water level in a cycle step.
1. Enter PROGRAM Mode. Refer to Entering
Program Mode section.
2. Press the ∧ keypad until display shows “CY01”.
3. Select the cycle by pressing the desired cycle
number.
11. Display shows “LO”, “nEd”, or “HI” for low,
medium, or high water level, respectively.
4. Press START keypad to edit the cycle.
12. Press the ∧ or ∨ keypad to alter the selection, or
the START keypad to continue.
Agitation for the Cycle
13. Display shows “SUP0”, “SUP1”, “SUP2”,
“SUP3”, “SUP4”, “SUP5”, “SUP6” or “SUP7”.
selection.
5. With display showing “CYXX” (xx = cycle
number), press the START keypad. Display
shows “AG1”, “AG2”, “AG3” or “AG4”. Refer to
Table 4 for a description on Agitation.
14. Press the ∧ or ∨ keypad to alter the selection, or
Display Meaning
the START keypad to continue.
AG1
AG2
AG3
AG4
18 seconds forward, 3 seconds pause, 18
seconds reverse, 3 seconds pause and repeat
for the programmed time
NOTE: “SUP5” and “SUP6” appear ONLY if
control is configured for “SUP5” in SETUP Mode.
If the alternate function is selected (“AFIL”), the
output will function as an additional fill valve
signal with a programmable water level. In this
case, the extra supply function would NOT be
available.
3 seconds forward, 27 seconds pause, 3
seconds reverse, 27 seconds pause and repeat
for the programmed time
10 seconds forward, 20 seconds pause, 10
seconds reverse, 20 seconds pause and repeat
for the programmed time
NOTE: If programmed for “SUP2”, the ADD
BLEACH indicator LED light turns on and the
buzzer sounds while supply 2 is on.
4 seconds forward, 56 seconds pause, 4
seconds reverse, 56 seconds pause and repeat
for the programmed time
15. Display shows “bEEP” or “nobP”.
Table 4
16. Press the ∧ or ∨ keypad to alter the selection or
START keypad to continue.
Wash 1 – Wash 5
The leftmost supply compartment (as seen from front
of machine), which can be used for detergent, flushes
during fill cycles whether Supply 1 option is enabled
or disabled. When Supply 1 option is enabled, Supply
1 (S1) output energizes and is available for external
chemical supply if desired. The Supply 2 option
controls the middle compartment, which can be used
for bleach. Supply 3 and Supply 7 options control the
rightmost compartment, which can be used for fabric
softener. Supply 4, Supply 5 and Supply 6 options
control external chemical supplies, as desired. Refer to
Table 3 for operation of each supply selection.
NOTE: Programming a time other than “00” for
Wash 1 will make the WASH indicator LED light
while this step is running, but NOT in PROGRAM
Mode.
6. The main display shows “USH1” indicating you
are in the Wash segment (number will reflect
selected Wash segment 1-5).
7. Press START keypad. Display shows agitation
time during the step: “00” (skips segment) or
2-30 minutes. This is the time after the fill and
before the drain and does not include spin time or
time to first reach a programmed temperature (if
your machine is configured for heat).
NOTE: For additional assistance, refer to
installation instructions.
8. Press the ∧ or ∨ keypad to alter the selection, or
the START keypad to continue.
9. Display shows “CFIL”, “HFIL”, “bFIL” (for
cold, hot, or warm [both]) or “AFIL”.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
13
Programming
Temperature Controlled Fill
Rinse 1 – Rinse 6
17. Display shows temperature in degrees F or C.
Display will show degrees F if configured for
“FAr” in SETUP Mode, or degrees C if
NOTE: Programming a time other than “00” for
this step will make the RINSE indicator LED light
while this step is running, but not in PROGRAM
Mode.
configured for “CEL” in SETUP Mode. Range is
75°F to 200°F, or 00F (no heat for segment), or
25°C to 93°C, or 00C (no heat for segment).
25. The main display shows “rIN1” indicating you
are in the Rinse segment (number will represent
Rinse cycle selected 1-6).
18. Press the ∧ keypad to increase, or ∨ keypad to
decrease temperature in one-degree increments.
26. Press START keypad. Display shows the time for
agitation during the step: “00” (skips segment) or
2-30 minutes.
The control will energize heat and pause cycle timing
for up to 40 minutes until the programmed
temperature is first reached.
NOTE: This is the time after the fill and before the
drain and does not include spin time.
NOTE: If temperature not reached after
40 minutes, control resumes cycle.
27. Press the ∧ or ∨ keypad to alter the selection.
After cycle resumes, control will attempt to maintain
programmed temperature if it senses water in the
machine.
28. Press the START keypad to continue.
29. Display shows “CFIL”, “HFIL”, “bFIL” (for
cold, hot, warm [both]) or “AFIL”.
19. If display shows “drAI”/“nodr” during segment
programming, a drain step option can be selected.
Select “drAI” for a drain step followed by an
optional spin. Select “nodr” for no drain step.
30. Press the ∧ or ∨ keypad to alter the selection.
31. Press the START keypad to continue.
NOTE: The machine will proceed directly to the
next segment if “nodr”.
NOTE: Auxiliary Fill (“AFIL”) possible only if
configured for “AFIL” in SETUP Mode. If
configured, auxiliary fills can be programmed to
low, medium, or high water level in cycle step.
20. Change the selection by pressing the ∧ or ∨
keypad.
32. Display shows “LO”, “nEd”, or “HI” for low,
medium, or high water level, respectively.
21. Press START to continue.
22. If “drAI” is selected (or if your model does not
provide the option of selecting “drAI”/“nodr”),
the display will show “SPIn” one second, “tInE”
one second, and then the time for spin: “00” (no
spin) or 60-240 seconds.
33. Press the ∧ or ∨ keypad to alter the selection.
34. Press the START keypad to continue.
35. Display shows “SUP0”, “SUP1”, “SUP2”,
“SUP3”, “SUP4”, “SUP5”, “SUP6” or “SUP7”.
selection.
23. Change the selection by pressing the ∧ or ∨
keypad.
24. Press START to continue.
36. Press the ∧ or ∨ keypad to alter the selection.
37. Press the START keypad to continue.
NOTE: “SUP5” and “SUP6” appear ONLY if
control is configured for “SUP5” in SETUP Mode.
If the alternate function is selected (“AFIL”), the
output will function as an additional fill valve
signal with a programmable water level. In this
case, the extra supply function would NOT be
available.
NOTE: If programmed for “SUP2”, the ADD
BLEACH indicator LED light turns on and the
buzzer sounds, if programmed, while supply 2 is
on.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
14
Programming
The leftmost supply compartment (as seen from front
of machine), which can be used for detergent, flushes
during fill cycles whether Supply 1 option is enabled
or disabled. When Supply 1 option is enabled, Supply
1 (S1) output energizes and is available for external
chemical supply if desired. The Supply 2 option
controls the middle compartment, which can be used
for bleach. Supply 3 and Supply 7 options control the
rightmost compartment, which can be used for fabric
softener. Supply 4, Supply 5, and Supply 6 options
control external chemical supplies, as desired. Refer to
Table 3 for operation of each supply selection.
45. If you are in Rinse 6, the time for spin will show
0 or 1-10 minutes.
46. Change the selection by pressing the ∧ or ∨
keypad.
47. Press START to continue.
IMPORTANT: The spin time in Rinse 6 is
programmed in minutes (0-10 minutes, in
one-minute increments). (Rinse 6 segment should
be used as the final rinse, even where there may be
fewer than four rinses. Program zero time for
preceding rinses you wish to exclude.)
NOTE: For additional assistance, refer to
installation instructions.
48. Display shows temperature.
49. Exit PROGRAM Mode by moving the Program/
Run switch back to the right as seen from the
front of the machine.
Temperature Controlled Fill
38. Display shows temperature in degrees F or C.
Display will show degrees F if configured for
“FAr” in SETUP Mode, or degrees C if
NOTE: The SPIN indicator LED will automatically
light during the wash cycle when the last spin
programmed in a cycle is operating (regardless of
which segment).
configured for “CEL” in SETUP Mode. Range is
75°F to 200°F, or 00F (no heat for segment), or
25°C to 93°C, or 00C (no heat for segment).
39. Press the ∧ keypad to increase, or ∨ keypad to
decrease temperature. Temperature changes in
one-degree increments.
The control will energize heat and pause cycle timing
for up to 40 minutes until the programmed temperature
is first reached.
NOTE: If temperature is not reached after
40 minutes, control resumes cycle.
After cycle resumes, control will attempt to maintain
programmed temperature if it senses water in the
machine.
40. If display shows “drAI”/“nodr” during segment
programming, a drain step option can be selected.
41. Select “drAI” for a drain step followed by an
optional spin. Select “nodr” for no drain step.
NOTE: The machine will proceed directly to the
next segment if “nodr”.
42. Change the selection by pressing the ∧ or ∨
keypad.
43. Press START to continue.
44. If “drAI” is selected (or if your model does not
provide the option of selecting “drAI”/“nodr”),
the display will show “SPIn” one second, “tInE”
one second, and then the time for spin:
“00” (no spin) for 60-240 seconds IF you are in
Rinse 1 – 5.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
15
Programming
Temperature Probe Sensor Problem
Abnormal Conditions
If display shows “tSFL”, the machine has a
temperature sensor failure. This could mean the sensor
is not connected or the sensor has failed.
Door Open During Operation
If the control senses either a momentary or sustained
open door while the machine is operating in a wash
cycle, the control immediately attempts to halt rotation
of the cylinder, and all outputs not required to effect
rapid halting of the cylinder rotation de-energize
immediately. The message “dOOr” then displays as
long as the condition persists. Regardless of the
duration of the open door condition, once it is
recognized by the control, the control aborts the cycle
and goes to the stop routine if the door is closed
(otherwise all outputs turn off and display shows
“dOOr”).
Clean Filter LED On
Variable-Speed Models Only
If the bottom indicator LED on front panel decal
lights, the temperature sensor in the inverter drive
compartment is indicating the temperature is
undesirably high. Check and clean the drive
compartment filter if necessary. Once corrected, the
light turns off AFTER one cycle runs at a normal
temperature.
Excessive Fill Time
WARNING
As indicated elsewhere in this definition, fill times
exceeding 10 minutes cause the cycle to abort and the
display flashes “StOP”/“FILL” or “ErFL” and sounds
the buzzer for ten seconds prior to entering the stop
routine (display shows “01” minutes remaining while
in the stop routine).
To reduce risk of electric shock, severe
injury or death, allow machine power to
remain off for three minutes minimum prior
to working in and around AC drive. Proceed
with caution.
W662
Out of Balance
Test Cycle
If the wash load becomes out of balance, the machine
will attempt to balance the load. After three failed
attempts, the display will light the leftmost digit and a
lower spin will be used to complete the cycle.
The test cycle provides a convenient means of
troubleshooting and testing all machine functions
quickly.
1. Enter PROGRAM Mode.
WARNING
2. Press the ∨ keypad. Display shows “tESt”.
3. Return the Program/Run switch to the right.
Operating the machine with severe out-of-
balance loads could result in personal
injury and serious equipment damage.
4. Press START keypad. The door locks and the
TEST Mode starts.
W728
5. Display shows “SPC?”. This is a factory test
procedure. Ignore it and the machine will
advance into the test cycle after about
Door Will Not Open
At the end of a cycle or at power up, before the control
will allow the door to unlock, control checks for low,
medium or high water level. Control allows the door to
unlock only when machine is empty. If any water level
is indicated, display shows “FULL” while keeping all
outputs off. This condition could indicate a slow drain
system or a mechanical blockage of the drain. Contact
a qualified service technician about display on control.
five seconds or go to “bAl?” if variable-speed.
NOTE: For variable-speed models ONLY, display
shows “bAl?”. This is also a special factory test
procedure. Ignore it and the machine will begin the
test cycle after a few seconds.
Excessive Drain Time
If cycle aborts, with display flashing “Erdn” with
buzzer sounding, the machine did not empty after
4 minutes 15 seconds in a drain step.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
F232224
16
Programming
Control Test
Warm fill to low water level
Display flashes “bFIL”/“LO” (WASH LED on) with agitation, LOW water level dot on
when level reached, then to next step.
Outputs: Motor ON, Drain closed, hot fill on, cold fill on
Cold fill to medium water level Display flashes “CFIL”/“nEd” (WASH LED on) with agitation, MEDIUM water level dot
on when level reached, then to next step.
Outputs: Motor ON, Drain closed, cold fill on
Hot fill to high water level
Heat and Supply 1 on
Heat and Supply 2 on
Heat and Supply 3 on
Supply 4 on
Display flashes “HFIL”/“HI” (WASH LED on) with agitation, HIGH water level dot on
when level reached, then to next step.
Outputs: Motor ON, Drain closed, hot fill on
Display flashes “HEAt”/“SUP1” (WASH LED on) with agitation, Supply 1 is on for 5
seconds, then to next step.
Outputs: Motor ON, Drain closed, Supply 1 on, Heat on
Display flashes “HEAt”/“SUP2” (BLEACH LED on) with agitation, Supply 2 is on for 5
seconds, then to next step.
Outputs: Motor ON, Drain closed, Supply 2 on, Heat on
Display flashes “HEAt”/“SUP3” (RINSE LED on) with agitation, Supply 3 is on for 5
seconds, then to next step.
Outputs: Motor ON, Drain closed, Supply 3 on, Heat on
Display shows “SUP4” (RINSE LED on) with agitation, Supply 4 is on for 5 seconds, then
to next step.
Outputs: Motor ON, Drain closed, Supply 4 on
Supply 5 or Auxilliary fill on
Display shows “SUP5” or “AFIL” (RINSE LED on) with agitation, Supply 5 is on for 5
seconds, then to next step.
Outputs: Motor ON, Drain closed, Supply 5/Auxilliary fill on
Motor rotates slow wash reverse Display flashes “SLo”/“rEv” for 60 seconds, then to next step.
Outputs: Motor ON (slow reverse)
Motor rotates slow wash
forward
Display flashes “SLo”/“For” for 60 seconds, then to next step.
Outputs: Motor ON (slow forward)
Motor rotates normal wash
reverse
Display flashes “norn”/“rEv” for 60 seconds, then to next step.
Outputs: Motor ON (normal reverse)
Motor rotates normal wash
forward
Display flashes “norn”/“For” for 60 seconds, then to next step.
Outputs: Motor ON (normal forward)
Drain and Distribution
Display flashes “drai”/“For” until machine drains, then to next step.
Outputs: Motor ON (distribution), Drain opens in 15-27 seconds
Display shows “SPn1” (SPIN LED on) for 60 seconds, then to next step.
Outputs: Motor ON (Low Spin)
Spin 1
Spin 2
Spin 3
Display shows “SPn2” (SPIN LED on) for 60 seconds, then to next step.
Outputs: Motor ON (Medium Spin)
Display shows “SPn3” (SPIN LED on) for 60 seconds, then to next step.
Outputs: Motor ON (High Spin)
Table 5 (Continued)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232224
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Table 5 (Continued)
Control Test
Spin coast delay
Stop routine
Displays “SdLY”, then to normal stop routine.
Outputs: All off
Display shows “StoP”, agitates briefly, shows “donE”, and allows door to unlock.
Table 5
NOTE: ON appears ONLY where motor control
outputs are on (otherwise they are off). Outputs
referenced are on control unit fuse board. Outputs
are as labeled on the fuse board.
Motor Speed Chart
Fixed-Speed and
2 Speed Motor
Outputs
Variable-Speed Motor Control
Outputs
STF
STR
RH
RM
RL
Fwd
Rev
Spin
Motor off (no rotation)
Wash speed forward
ON
ON
ON
ON
NA
ON
ON
NA
Wash speed reverse
ON
ON
ON
NA
ON
Distribution (variable-speed ONLY)
ON
ON
ON
ON
Lowest spin (low spin speed “SPn1” for
variable-speed)
ON
ON
ON
ON
NA
NA
NA
NA
NA
NA
Medium spin (“SPn2” – variable-speed ONLY)
Highest spin (“SPn3” – variable-speed ONLY)
NA – Not Applicable
NOTE: For variable-speed machines smaller than
C80, SPn1 and SPn2 are not the same speed.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232224
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Domestic Cycle Charts Custom
Cycles 1 - 24
Permanent Cotton
Table
Napery
Blends
Colors
Table
Napery
Blends
Whites
Delicates
Spreads
Cold
Delicates
Spreads
Warm (Both)
Water
Permanent Cotton
Press Terrycloth
Light Soil Light Soil
Permanent
Press
Cotton
VISA Table VISA Table
Personals Personals
Press
Medium
Soil
Terrycloth
Medium
Soil
Rags
Heavy Soil
Cycle Steps
Terrycloth
Napery
Colors
Napery
Whites
Reclaim
with
No
Heavy Soil Heavy Soil
Bleach
Bleach
Water
Cycle reference (display in Program Mode)
Agitation
CY01
AG1
CY02
AG1
CY03
AG1
CY04
AG1
CY05
AG1
CY06
AG1
CY11
AG1
CY12
AG1
CY13
AG1
CY14
AG1
CY15
AG1
CY16
AG1
CY21
AG1
CY22
AG1
CY23
AG1
CY24
AG1
Wash 1 (WASH Indicator On)
Time for agitation (minutes)
7
Hot
Low
1
7
Hot
Low
1
2
2
2
2
2
2
2
2
2
2
7
Hot
Low
1
7
5
Cold
High
1
5
Fill Valves (temperature)
Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both)
Warm (Both)
Warm (Both)
Fill water level
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
1
Low
1
High
1
Supply
Heat (If enabled)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Drain
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Spin (only if preceded by ‘drain’) seconds
Wash 2 (WASH Indicator On)
Time for agitation (minutes)
6
Hot
Low
1
6
Hot
Low
1
7
Hot
Low
1
7
Hot
Low
1
9
Hot
Low
1
9
Hot
Low
1
12
Hot
Low
1
12
Hot
Low
1
10
Hot
Low
1
12
Hot
Low
1 & 2
0
7
Hot
Low
2
7
2
Cold
High
0
2
Fill Valves (temperature)
Warm (Both)
Warm (Both)
Fill water level
High
0
High
0
Supply
Heat (if enabled)
0
0
0
0
0
0
0
0
0
0
0
0
0
Drain
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Spin (only if preceded by ‘drain’) seconds
Wash 3 (WASH Indicator On)
Time for agitation (minutes)
7
Hot
Low
2
7
Hot
Low
2
7
Hot
Low
2
7
Hot
Low
2
2
7
Hot
Low
2
2
2
6
Hot
High
2
12
Hot
Low
1 & 2
0
Fill Valves (temperature)
Warm (Both)
Warm (Both) Warm (Both)
Fill water level
High
0
High
0
High
0
Supply
Heat (if enabled)
0
0
0
0
0
0
0
0
0
Drain
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Spin (only if preceded by ‘drain’) seconds
Wash 4 (WASH Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Wash 5 (WASH Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Table 6 (continued)
Download from Www.Somanuals.com. All Manuals Search And Download.
Permanent Cotton
Table
Napery
Blends
Colors
Table
Napery
Blends
Whites
Delicates
Spreads
Warm (Both)
Water
Cotton
Terrycloth
Light Soil
Permanent
Press
Cotton
VISA Table VISA Table
Personals Personals Delicates
Permanent
Light Soil
Press
Medium
Soil
Terrycloth
Medium
Soil
Rags
Heavy Soil
Cycle Steps
Terrycloth
Napery
Colors
Napery
Whites
Reclaim
with
No
Spreads
Heavy Soil Heavy Soil
Bleach
Bleach Cold Water
Cycle reference (display in Program Mode)
Agitation
CY01
AG1
CY02
AG1
CY03
AG1
CY04
AG1
CY05
AG1
CY06
AG1
CY11
AG1
CY12
AG1
CY13
AG1
CY14
AG1
CY15
AG1
CY16
AG1
CY21
AG1
CY22
AG1
CY23
AG1
CY24
AG1
Rinse 1 (Rinse Indicator On)
Time for agitation (minutes)
2
2
2
Hot
High
0
2
Hot
High
0
2
Hot
High
0
2
Hot
High
0
2
2
2
2
2
Hot
High
0
4
2
2
2
Cold
High
0
2
Fill Valves (temperature)
Warm (Both) Warm (Both)
Warm (Both) Warm (Both) Warm (Both) Warm (Both)
Warm (Both) Warm (Both) Warm (Both)
Warm (Both)
Fill water level
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
0
Supply
Heat (If enabled)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Drain
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
0
Yes
60
Yes
60
Yes
60
Yes
60
Spin (only if preceded by ‘drain’) seconds
Rinse 2 (Rinse Indicator On)
Time for agitation (minutes)
2
2
2
2
2
2
2
2
2
2
2
Fill Valves (temperature)
Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both)
Warm (Both) Warm (Both) Warm (Both)
Fill water level
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
0
High
0
Supply
Heat (if enabled)
0
0
0
0
0
0
0
0
0
0
0
Drain
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
0
Yes
60
Yes
0
Spin (only if preceded by ‘drain’) seconds
Rinse 3 (Rinse Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Rinse 4 (Rinse Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Rinse 5 (Rinse Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Final Spin (Rinse Indicator On)
Time for agitation (minutes)
4
4
4
4
5
4
4
4
4
4
4
4
4
4
4
Cold
High
3
4
Cold
High
3
Fill Valves (temperature)
Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both) Warm (Both)
Fill water level
Low
3
Low
3
Low
3
Low
3
Low
3
Low
3
Low
3
Low
3
Low
3
Low
3
Low
3
Low
3
Low
3
Low
3
Supply
Heat (if enabled)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Drain
Yes
SPN3
5
Yes
SPN3
5
Yes
SPN3
5
Yes
SPN3
5
Yes
SPN3
5
Yes
SPN3
5
Yes
SPN3
5
Yes
SPN3
5
Yes
SPN1
5
Yes
SPN1
5
Yes
SPN3
5
Yes
SPN3
5
Yes
SPN1
5
Yes
SPN1
5
Yes
SPN1
3
Yes
SPN1
3
Spin Speed
Spin (only if preceded by ‘drain’) minutes
Table 6 (continued)
Download from Www.Somanuals.com. All Manuals Search And Download.
International Cycle Charts Custom
Cycles 31 - 46
Permanent
Press 90°C
(Pre Wash)
Permanent
Permanent
Normal 90°C
(Pre Wash)
Normal 60°C
Normal 40°C
(Pre Wash)
Permanent
Press 90°C
Cycle Steps
Normal 90°C
Normal 60°C
Press 60°C Press 60°C
(Pre Wash)
Fine 40°C
Custom #1 Custom #2 Custom #3 Custom #4
CY25 CY26 CY36 CY46
(Pre Wash)
CY31
AG1
CY32
AG1
CY33
AG1
CY34
AG1
CY35
AG1
CY41
AG1
CY42
AG1
CY43
AG1
CY44
AG1
CY45
AG2
Cycle reference (display in Program Mode)
Agitation
Wash 1 (WASH Indicator On)
Time for agitation (minutes)
8
Cold
High
1
10
Hot
Low
1 & 2
90°
Yes
0
8
Cold
High
1
10
Hot
Low
1 & 2
60°
Yes
0
6
Cold
High
1
8
Cold
High
1
10
Hot
Low
1 & 2
90°
Yes
0
8
Cold
High
1
10
Hot
Low
1 & 2
60°
Yes
0
6
Cold
High
1
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
40°
Yes
0
40°
Yes
0
40°
Yes
0
40°
Yes
0
40°
Yes
0
40°
Yes
0
Drain
Spin (only if preceded by ‘drain’) seconds
Wash 2 (WASH Indicator On)
Time for agitation (minutes)
10
Hot
Low
2
2
Cold
Medium
0
10
Hot
Low
2
2
Cold
Medium
0
8
10
Hot
Low
2
2
Cold
Medium
0
10
Hot
Low
2
2
Cold
Medium
0
8
Fill Valves (temperature)
Warm (Both)
Warm (Both)
Fill water level
Low
2
Low
2
Supply
Heat (if enabled)
90°
Yes
0
0
60°
Yes
0
0
40°
Yes
0
90°
Yes
0
0
60°
Yes
0
0
40°
Yes
0
Drain
Yes
60
Yes
60
Yes
60
Yes
60
Spin (only if preceded by ‘drain’) seconds
Wash 3 (WASH Indicator On)
Time for agitation (minutes)
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
0
0
0
0
0
0
Drain
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Spin (only if preceded by ‘drain’) seconds
Wash 4 (WASH Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Wash 5 (WASH Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Table 6 (continuted)
Download from Www.Somanuals.com. All Manuals Search And Download.
T
Permanent
Press 90°C
(Pre Wash)
Permanent
Press 60°C
(Pre Wash)
Permanent
Normal 90°C
(Pre Wash)
Normal 60°C
(Pre Wash)
Normal 40°C
(Pre Wash)
Permanent
Press 90°C
Cycle Steps
Normal 90°C
Normal 60°C
Press 60°C Fine 40°C Custom #1 Custom #2 Custom #3 Custom #4
CY31
AG1
CY32
AG1
CY33
AG1
CY34
AG1
CY35
AG1
CY41
AG1
CY42
AG1
CY43
AG1
CY44
AG1
CY45
AG2
CY25
CY26
CY36
CY46
Cycle Reference (Display in Program Mode)
Agitation
Rinse 1 (Rinse Indicator On)
Time for agitation (minutes)
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
0
0
0
0
0
0
0
0
0
0
Drain
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Spin (only if preceded by ‘drain’) seconds
Rinse 2 (Rinse Indicator On)
Time for agitation (minutes)
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
0
0
0
0
0
0
0
0
0
0
Drain
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Yes
60
Spin (only if preceded by ‘drain’) seconds
Rinse 3 (Rinse Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Rinse 4 (Rinse Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Rinse 5 (Rinse Indicator On)
Time for agitation (minutes)
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
Drain
Spin (only if preceded by ‘drain’) seconds
Final Spin (Rinse Indicator On)
Time for agitation (minutes)
2
Cold
Medium
3
2
Cold
Medium
3
2
Cold
Medium
3
2
Cold
Medium
3
2
Cold
Medium
3
2
Cold
Medium
3
2
Cold
Medium
3
2
Cold
Medium
3
2
Cold
Medium
3
2
Cold
Medium
3
Fill Valves (temperature)
Fill water level
Supply
Heat (if enabled)
0
0
0
0
0
0
0
0
0
0
Drain
Yes
SPN3
2
Yes
SPN3
2
Yes
SPN3
2
Yes
SPN3
2
Yes
SPN3
2
Yes
SPN3
2
Yes
SPN3
2
Yes
SPN3
2
Yes
SPN3
2
Yes
SPN3
2
Spin Speed
Spin (only if preceded by ‘drain’) minutes
Table 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|