Part No. 031496-00, Rev. C
September 2005
OmniSwitch 6624/6648/
6800/7700/7800/8800
Troubleshooting Guide
www.alcatel.com
OmniSwitch Troubleshooting Guide September 2005
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
About This Guide .........................................................................................................xv
What is Not in this Manual? ...........................................................................................xvii
How is the Information Organized? ...............................................................................xvii
Related Documentation ..................................................................................................xvii
Before Calling Alcatel’s Technical Assistance Center .................................................... xx
Troubleshooting the Switch System ......................................................................1-1
In This Chapter ................................................................................................................1-1
Introduction .....................................................................................................................1-2
Advanced Troubleshooting .............................................................................................1-9
Dshell Troubleshooting .................................................................................................1-11
Accessing Dshell on Idle Switches ..................................................................1-25
Using AlcatelDebug.cfg ................................................................................................1-26
Debugging IPC .......................................................................................................1-27
OmniSwitch 6624/6648 Example ..........................................................................1-34
Port Numbering Conversion Overview .........................................................................1-36
ifindex to gport .......................................................................................................1-36
gport to ifindex .......................................................................................................1-36
Converting from lport .............................................................................................1-36
In This Chapter ................................................................................................................2-1
Overview of Troubleshooting Approach ........................................................................2-2
Verify Physical Layer Connectivity ................................................................................2-3
Verify Current Running Configuration ...........................................................................2-5
OmniSwitch Troubleshooting Guide September 2005
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Verify Source Learning ...................................................................................................2-6
Verify Switch Health .......................................................................................................2-7
Verify ARP ......................................................................................................................2-7
Using the Log File ...........................................................................................................2-8
Checking the 7700/7800 Nantucket Fabric ..............................................................2-8
Checking the 7700/7800 Nantucket Fabric for Interrupts, Data Counts and
Error Counts ............................................................................................................2-9
Checking the Traffic Queue on the NI .....................................................................2-9
Check for Catalina (MAC) or Port Lockup ............................................................2-10
Troubleshooting Source Learning .........................................................................3-1
In This Chapter ................................................................................................................3-1
Introduction .....................................................................................................................3-2
Troubleshooting a Source Learning Problem .................................................................3-3
Advanced Troubleshooting .............................................................................................3-5
Dshell Troubleshooting ...................................................................................................3-7
OS-6600 .................................................................................................................3-10
Troubleshooting Spanning Tree ............................................................................4-1
In This Chapter ................................................................................................................4-1
Introduction .....................................................................................................................4-1
Troubleshooting Spanning Tree ......................................................................................4-2
Dshell ..............................................................................................................................4-5
Generic Troubleshooting in Dshell ...............................................................................4-10
Event Trace (stpni_traceprint) ................................................................................4-10
PORTATCH ....................................................................................................4-11
PORTDELE .....................................................................................................4-11
ADDVLAN .....................................................................................................4-11
MODVLADM .................................................................................................4-12
MODVLSTP ....................................................................................................4-12
ADDQTAG .....................................................................................................4-12
DELQTAG ......................................................................................................4-12
MDEFVLAN ...................................................................................................4-13
PORTAGGR ....................................................................................................4-13
PORTDISG ......................................................................................................4-13
AGGR_UP .......................................................................................................4-13
AGGRDOWN .................................................................................................4-13
PORTJOIN ......................................................................................................4-14
PORTLEAV ....................................................................................................4-14
BRGPARAM ...................................................................................................4-14
PTSTPMOD ....................................................................................................4-15
PORTMOD ......................................................................................................4-15
PORTVLBK ....................................................................................................4-15
PVLANBLK ....................................................................................................4-15
GMBPDU ........................................................................................................4-16
iv
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
GMIGBPDU ....................................................................................................4-16
GM2FIXED .....................................................................................................4-17
VMADDVPA ..................................................................................................4-17
VMDELVPA ...................................................................................................4-17
VMDEFVPA ...................................................................................................4-17
TOPOCHGT ....................................................................................................4-18
LINK_UP ........................................................................................................4-18
LINKDOWN ...................................................................................................4-18
NI_UP ..............................................................................................................4-18
NI_DOWN ......................................................................................................4-18
Physical and Logical Port Dumps ..........................................................................4-19
Logical Ports (stpni_debugLport) ....................................................................4-19
Physical Port (stpni_debugPport) ....................................................................4-20
Socket Handler Traces ...........................................................................................4-22
stpNISock_globals ...........................................................................................4-22
stpNISock_warningprint ..................................................................................4-23
stpNISock_traceprint .......................................................................................4-23
Inter-NI Trace (stpNISock_intraceprint) .........................................................4-24
Board Up (stpNISock_boardupprint) ..............................................................4-24
stpNISock_printon ...........................................................................................4-24
StpNISock_printoff .........................................................................................4-24
CMM Spanning Tree Traces ..................................................................................4-25
Trace Menu ......................................................................................................4-25
stpCMM_traceprint .........................................................................................4-25
Writing a PR for Spanning Tree ....................................................................................4-26
Port Does Not Forward ..........................................................................................4-26
Other Cases ............................................................................................................4-27
In This Chapter ................................................................................................................5-1
Starting the Troubleshooting Procedure ..........................................................................5-1
Use a Network Diagram ...........................................................................................5-2
UDP Relay Configuration Problems ........................................................................5-2
Incorrect Server IP Address ...............................................................................5-2
Forward Delay Timer ........................................................................................5-3
Displaying DHCP Statistics ..............................................................................5-3
UDP Relay and Group Mobility ...............................................................................5-4
Advanced Troubleshooting for UDP Relay ....................................................................5-5
Dshell ..............................................................................................................................5-6
Troubleshooting DNS ................................................................................................6-1
In This Chapter ................................................................................................................6-1
Introduction .....................................................................................................................6-1
OmniSwitch Troubleshooting Guide September 2005
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting a DNS Failure ......................................................................................6-2
Starting the Troubleshooting Procedure ...................................................................6-2
Layer 7 DNS or Name Resolution Issue ..................................................................6-2
DNS Configuration Considerations ................................................................................6-3
Troubleshooting Link Aggregation .......................................................................7-1
In This Chapter ................................................................................................................7-1
Link Aggregation Limits and Guidelines ........................................................................7-2
OmniSwitch 6624/6648 Restrictions .......................................................................7-2
Troubleshooting a Link Aggregation Failure ..................................................................7-3
Verify the Configuration ..........................................................................................7-3
Source Learning .......................................................................................................7-5
Link Aggregation Affecting Other Traffic ...............................................................7-5
Problems Creating a Group ......................................................................................7-5
Problems Deleting a Group ......................................................................................7-5
LACP 802.3AD ........................................................................................................7-6
Advanced Link Aggregation Troubleshooting ................................................................7-7
6800 Link Aggregation Debug Functions .....................................................................7-10
la_ni_agg_prt ..........................................................................................................7-10
la_ni_port_prt .........................................................................................................7-10
la_ni_port_up_prt ...................................................................................................7-11
la_ni_port_stats_prt ................................................................................................7-11
la_ni_info ...............................................................................................................7-11
lagg_ni_Sock_help .................................................................................................7-11
la_ni_trace_freeze ..................................................................................................7-12
la_ni_trace_unfreeze ..............................................................................................7-12
la_ni_kite_help .......................................................................................................7-12
Troubleshooting 802.1Q ..........................................................................................8-1
In This Chapter ................................................................................................................8-1
Troubleshooting 802.1Q .................................................................................................8-2
Default VLAN Traffic ..............................................................................................8-3
Tagged Packet on an Untagged Port ........................................................................8-3
802.1Q with VLAN ID of 0 ..............................................................................8-4
802.1Q and 64 Byte Packets ..............................................................................8-4
Advanced Troubleshooting .............................................................................................8-5
Dshell Commands ...........................................................................................................8-7
Troubleshooting Group Mobility ............................................................................9-1
In This Chapter ................................................................................................................9-1
Troubleshooting a VLAN Mobility Failure ....................................................................9-2
Binding Rules ...........................................................................................................9-3
Port Rules .................................................................................................................9-3
Precedence ................................................................................................................9-4
Advanced Troubleshooting .............................................................................................9-5
vi
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell ..............................................................................................................................9-6
NI Debug Dshell .......................................................................................................9-6
6800 Group Mobility Troubleshooting ...........................................................................9-7
show vlan rules .........................................................................................................9-7
gmHelp .....................................................................................................................9-7
gmcKiteDebug .........................................................................................................9-8
gmcShowPorts ..........................................................................................................9-8
gmcShowRules .........................................................................................................9-8
gmnKiteDebug .........................................................................................................9-9
gmnKiteShowRules ..................................................................................................9-9
gmnMacVlanShowBuffer ........................................................................................9-9
Troubleshooting QoS ...............................................................................................10-1
In This Chapter ..............................................................................................................10-1
QoS Behavior ................................................................................................................10-2
Default ....................................................................................................................10-2
QoS Queues and Ports ............................................................................................10-2
Troubleshooting QoS ....................................................................................................10-3
Starting the Troubleshooting Procedure .................................................................10-3
QoS Activation .......................................................................................................10-3
QoS Apply ..............................................................................................................10-4
Invalid Policies .......................................................................................................10-4
Rules Order ............................................................................................................10-4
Viewing QoS Settings ............................................................................................10-5
Viewing QoS Policy Rules .....................................................................................10-5
Validation ...............................................................................................................10-6
Example 1 ........................................................................................................10-6
Example 2 ........................................................................................................10-6
Example 3 ........................................................................................................10-7
Correction ...............................................................................................................10-8
Reflexive Rules ......................................................................................................10-8
QoS Log .................................................................................................................10-9
QoS Statistics .......................................................................................................10-11
Debug QoS ...........................................................................................................10-11
Debug QoS Internal ..............................................................................................10-12
qosIxHelp ......................................................................................................10-13
qosDBState ....................................................................................................10-13
QoS Dump .....................................................................................................10-13
Example QoS Rules ....................................................................................................10-15
Troubleshooting ARP ...............................................................................................11-1
In This Chapter ..............................................................................................................11-1
ARP Protocol Failure ....................................................................................................11-2
Common Error Conditions ............................................................................................11-5
Advanced ARP Troubleshooting ..................................................................................11-6
OmniSwitch Troubleshooting Guide September 2005
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting .................................................................................................11-8
Troubleshooting IP Routing ...................................................................................12-1
In This Chapter ..............................................................................................................12-2
Introduction ...................................................................................................................12-3
IP Routing Protocol Failure ..........................................................................................12-3
Troubleshooting via the CLI .........................................................................................12-3
Troubleshooting with Debug CLI ...............................................................................12-11
RIP Troubleshooting ...................................................................................................12-13
OSPF Troubleshooting ................................................................................................12-19
BGP Troubleshooting ..................................................................................................12-27
Dshell Troubleshooting Advanced IP Routing ...........................................................12-29
ipdbg=x .................................................................................................................12-29
ifShow ..................................................................................................................12-29
iprmShowRoutes ..................................................................................................12-30
iprmCountRoutes .................................................................................................12-30
ipni_ifShow ..........................................................................................................12-30
Iprm_routeShow ...................................................................................................12-31
Ipni_routeCount ...................................................................................................12-31
ospfDbgDumpEnv ................................................................................................12-31
In This Chapter ..............................................................................................................13-1
Overview .......................................................................................................................13-2
Protocol Information .....................................................................................................13-3
IP Field Descriptions ..............................................................................................13-3
VRRP Field Descriptions .......................................................................................13-3
VRRP States ...........................................................................................................13-3
OmniSwitch 7700/7800/8800 Implementation .............................................................13-4
VRRP Security .......................................................................................................13-4
OmniSwitch VRRP Limitations .............................................................................13-4
CMM Failover ...............................................................................................................13-5
OmniSwitch VRRP Troubleshooting ............................................................................13-9
ARP Table ...................................................................................................................13-10
Dshell Troubleshooting ...............................................................................................13-11
In This Chapter ..............................................................................................................14-1
Troubleshooting IPMS in Debug CLI ...........................................................................14-7
viii
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting .................................................................................................14-9
Troubleshooting DVMRP ........................................................................................15-1
In This Chapter ..............................................................................................................15-1
Introduction ...................................................................................................................15-2
DVMRP Troubleshooting .............................................................................................15-2
DVMRP Global and Interface Commands .............................................................15-2
DVMRP Debug Commands ...................................................................................15-4
Troubleshooting PIM-SM ........................................................................................16-1
In This Chapter ..............................................................................................................16-1
Introduction ...................................................................................................................16-2
Definition of Terms .......................................................................................................16-2
Protocol Overview ........................................................................................................16-3
DR Election ............................................................................................................16-3
Simplified Hello Message Format ...................................................................16-3
Debugging Hello Messages .............................................................................16-4
Related CLI Command ....................................................................................16-5
BSR Election .................................................................................................................16-6
Simplified Packet Format .......................................................................................16-7
Debugging BSR/Bootstrap .....................................................................................16-7
Election of a New BSR ....................................................................................16-8
Related CLI Command ....................................................................................16-9
C-RP Advertisements ..................................................................................................16-10
Simplified RP-Advertisement Packet Format ......................................................16-10
Debugging C-RP-Adv ..........................................................................................16-11
Related CLI Command ..................................................................................16-12
RP-SET .......................................................................................................................16-13
Debugging RP-SET ..............................................................................................16-16
On Non BSR You Should See .......................................................................16-16
Related CLI Command ..................................................................................16-17
Simplified Join Packet ..........................................................................................16-18
Simplified PRUNE Packet ...................................................................................16-20
Debugging JOIN/PRUNE Event ..........................................................................16-20
Register .......................................................................................................................16-21
Simplified REGISTER Packet Format .................................................................16-22
Shared Tree .................................................................................................................16-23
Related CLI Command ..................................................................................16-24
Source-Based Tree ......................................................................................................16-25
Related CLI Command ..................................................................................16-26
Troubleshooting Examples: Limitations .....................................................................16-27
Incorrect BSR ID ..................................................................................................16-27
OmniSwitch Troubleshooting Guide September 2005
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Multicast Group Status is Shown as Disabled .....................................................16-27
PIM-SM Limitations ............................................................................................16-28
Troubleshooting Server Load Balancing ...........................................................17-1
In This Chapter ..............................................................................................................17-1
Introduction ...................................................................................................................17-2
Server Load Balance Failure .........................................................................................17-2
What is an SLB Failure? ........................................................................................17-2
Description of a Complete Failure of Service ........................................................17-2
Description of a Partial Failure of Service .............................................................17-2
Troubleshooting Commands .........................................................................................17-3
Troubleshooting a Complete Failure .............................................................................17-4
Troubleshooting a Partial Failure ..................................................................................17-5
The Troubleshooting Procedure ....................................................................................17-5
Troubleshooting Authenticated VLANs ..............................................................18-1
In This Chapter ..............................................................................................................18-1
Introduction ...................................................................................................................18-1
Troubleshooting AVLAN .............................................................................................18-2
DHCP Request Failure ...........................................................................................18-2
Authentication Failure ............................................................................................18-3
Useful Notes on Client Issues ................................................................................18-5
Troubleshooting Using Debug Systrace ........................................................................18-5
Telnet Authentication and De-authentication ........................................................18-5
Initiate the Telnet Authentication ....................................................................18-6
Release/Renew IP ............................................................................................18-7
De-Authenticating ...........................................................................................18-7
HTTP/S Authentication ..........................................................................................18-8
Start of Authentication using https://x.x.x.253 ................................................18-8
De-Authenticate using https://x.x.x.253 ..........................................................18-9
AVClient ..............................................................................................................18-10
AVClient Authentication Start ......................................................................18-10
AVClient logout: ...........................................................................................18-11
Dshell Troubleshooting ...............................................................................................18-12
x
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1X .........................................................................................19-1
In This Chapter ..............................................................................................................19-1
Troubleshooting with the CLI .......................................................................................19-2
Troubleshooting Using Debug CLI ...............................................................................19-4
Dshell Troubleshooting .................................................................................................19-7
In This Chapter ...............................................................................................................A-1
The MAC ASIC .............................................................................................................A-2
Catalina ....................................................................................................................A-2
Firenze .....................................................................................................................A-4
The Coronado ASIC ................................................................................................A-5
Functional Description ............................................................................................A-6
Coronado: The “Brain” of the System ..............................................................A-7
Coronado Specifications ...................................................................................A-7
Software Module Interaction ............................................................................A-8
Queue Driver Interaction ................................................................................................A-8
Ethernet Driver ........................................................................................................A-8
Queue Dispatcher ....................................................................................................A-8
NI Supervision .........................................................................................................A-9
Source Learning ......................................................................................................A-9
L3 Manager/IPMS ...................................................................................................A-9
QoS Manager ...........................................................................................................A-9
Destination MAC Learning ..............................................................................A-9
L3 Pseudo CAM Learning ................................................................................A-9
QoS Policy Change ...........................................................................................A-9
QoS Policy Deleted ........................................................................................A-10
L2 destination MAC Aged/Deleted ................................................................A-10
Link Goes Up/Down .......................................................................................A-10
Link Aggregation .........................................................................................................A-11
Coronado Tables ..........................................................................................................A-11
Layer 2 Tables .......................................................................................................A-11
Layer 3 Tables .......................................................................................................A-11
Source Learning ...........................................................................................................A-12
Hardware Routing Engine (HRE) ................................................................................A-13
QoS/Policy Manager ....................................................................................................A-15
Coronado Egress Logic ................................................................................................A-15
The Fabric Architecture ...............................................................................................A-16
Nantucket ASIC ...........................................................................................................A-17
Additional Nantucket Specifications .....................................................................A-17
Functional Description: ..................................................................................A-18
Data Flow .......................................................................................................A-18
OmniSwitch Troubleshooting Guide September 2005
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Calendar Manager Module ....................................................................................A-19
Data Port Output Module ......................................................................................A-19
Nantucket Redundancy .........................................................................................A-19
Roma ............................................................................................................................A-22
Functional Description ..........................................................................................A-23
Initialization ....................................................................................................A-24
NI Slot Insertion .............................................................................................A-25
NI Slot Extraction ...........................................................................................A-25
CMM Takeover and Hot Swap .............................................................................A-25
Framing Error ........................................................................................................A-26
Chassis Management Module (CMM) .........................................................................A-26
OS7000 CMM .......................................................................................................A-27
OS8800 CMM .......................................................................................................A-27
Functional Description of CMM ...........................................................................A-28
CMM Software Startup Process .....................................................................A-28
AOS ................................................................................................................A-29
MiniBoot ........................................................................................................A-30
AOS Start ........................................................................................................A-30
CMM Reload of NI Module ..................................................................................A-30
Overall System Architecture .................................................................................A-32
Packet Walk .................................................................................................................A-34
Packet Walk Principles ..........................................................................................A-34
Data Flow Overview .............................................................................................A-34
Specific Packet Flows ..................................................................................................A-35
The Catalina ASIC .........................................................................................A-35
The Coronado ASIC .......................................................................................A-35
The Nantucket ASIC ......................................................................................A-35
The Coronado ASIC .......................................................................................A-35
The Catalina ASIC .........................................................................................A-35
Unknown Destination ...................................................................................................A-36
The Catalina ASIC .........................................................................................A-36
The Coronado ASIC .......................................................................................A-36
The Nantucket ASIC ......................................................................................A-36
The Coronado ASIC .......................................................................................A-37
The Catalina ASIC .........................................................................................A-37
Traffic is Being Passed; the Switch is Attempting to Put a Correct L2 DA
Entry on the NI .....................................................................................................A-37
The Coronado ASIC .......................................................................................A-37
Unknown L3 DA ...................................................................................................A-38
The Coronado ASIC .......................................................................................A-38
Xybus ....................................................................................................................A-41
Fbus .......................................................................................................................A-41
Bbus .......................................................................................................................A-41
xii
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Xybus Mapping .....................................................................................................A-42
Fbus Mapping ........................................................................................................A-42
OS6624/6648 Architecture ...........................................................................................A-43
Hardware Architectural Overview ........................................................................A-44
Layer 2 Forwarding ...............................................................................................A-46
Address Resolution Protocol ..........................................................................A-46
Address Learning ............................................................................................A-47
Location of Address Tables ............................................................................A-47
Address Look-up Methodology ......................................................................A-48
L2 Data Structures ..........................................................................................A-48
3-Protocol Entry .............................................................................................A-49
Layer 3 Forwarding ...............................................................................................A-50
VLANs ..................................................................................................................A-51
Port Based VLANs .........................................................................................A-51
Protocol Based VLANs ..................................................................................A-51
Address Based VLANs ...................................................................................A-51
Tag Net ID Entry ............................................................................................A-52
Priority ............................................................................................................A-52
802.1p Priority ................................................................................................A-52
Rules-Based Priority .......................................................................................A-53
QOS Flow .......................................................................................................A-53
CMM Functionality for OS6600 ..................................................................................A-54
OS6600 IPC Communication .......................................................................................A-58
OS6600 BOOT Sequence ............................................................................................A-59
Debug Commands ..................................................................................................... B-1
Technical Support Commands ............................................................................... C-1
Modifying Files with VI Editor ................................................................................D-1
In This Chapter ...............................................................................................................D-1
Useful VI Commands .....................................................................................................D-2
Sample VI Session .........................................................................................................D-3
Index ...................................................................................................................... Index-1
OmniSwitch Troubleshooting Guide September 2005
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
xiv
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
This OmniSwitch Troubleshooting Guide describes how to use Command Line Interface (CLI) and Dshell
commands available on the OmniSwitch 6600 Family, OmniSwitch 6800 Series, OmniSwitch 7700/7800,
and the OmniSwitch 8800 to troubleshoot switch and network problems.
Supported Platforms
This information in this guide applies to the following products:
• OmniSwitch 6624 (OmniSwitch 6600-24)
• OmniSwitch 6648 (OmniSwitch 6600-48)
• OmniSwitch 6600-P24
• OmniSwitch 6600-U24
• OmniSwitch 6602-24
• OmniSwitch 6602-48
• OmniSwitch 6800
• OmniSwitch 7700
• OmniSwitch 7800
• OmniSwitch 8800
Note. All references to OmniSwitch 6624 and 6648 switches also apply to the OmniSwitch 6600-P24,
OmniSwitch 6600-U24, OmniSwitch 6602-24, and OmniSwitch 6602-48 unless specified otherwise.
Unsupported Platforms
The information in this guide does not apply to the following products:
• OmniSwitch (original version with no numeric model name)
• Omni Switch/Router
• OmniStack
• OmniAccess
OmniSwitch Troubleshooting Guide September 2005
page -xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Note. Troubleshooting documentation for legacy products (e.g., Omni Switch/Router) can be downloaded
at http://support.ind.alcatel.com/releasefiles/indexpage.cfm.
Who Should Read this Manual?
The principal audience for this user guide is Service and Support personnel who need to troubleshoot
switch problems in a live network. In addition, network administrators and IT support personnel who need
to configure and maintain switches and routers can use this guide to troubleshoot a problem upon advice
from Alcatel Service and Support personnel..
However, this guide is not intended for novice or first-time users of Alcatel OmniSwitches. Misuse or fail-
ure to follow procedures in this guide correctly can cause lengthy network down time and/or permanent
damage to hardware. Caution must be followed on distribution of this document.
When Should I Read this Manual?
Always read the appropriate section or sections of this guide before you log into a switch to troubleshoot
problems. Once you are familiar with the commands and procedures in the appropriate sections you can
use this document as reference material when you troubleshoot a problem.
What is in this Manual?
The principal sections (i.e., the chapters numbered numerically) use CLI and Dshell commands to analyze
and troubleshoot switch problems. Each section documents a specific switch feature (e.g., hardware, server
load balancing, routing).
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
Appendix A provides an architecture overview for the OmniSwitch 6600 Family, OmniSwitch 7700/7800,
and the OmniSwitch 8800.
Appendices B and C provide the following for debug and technical support CLI commands:
• Command description.
• Syntax.
• Description of keywords and variables included in the syntax.
• Default values.
• Usage guidelines, which include tips on when and how to use the command.
• Examples of command lines using the command.
page -xvi
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
• Related commands.
• Release history, which indicates the release when the command was introduced.
Appendix D provides a list of useful VI editor commands and a sample VI session that modifies the
boot.params file.
What is Not in this Manual?
This guide is intended for troubleshooting switches in live networks. It does not provide step-by-step
instructions on how to set up particular features on the switch or a comprehensive reference to all CLI
commands available in the OmniSwitch. For detailed syntax on non debug CLI commands and compre-
hensive information on how to configure particular software features in the switch, consult the user
How is the Information Organized?
Each chapter in this guide includes troubleshooting guidelines related to a single software feature, such as
server load balancing or link aggregation.
Related Documentation
The following are the titles and descriptions of all the Release 5.1 and later OmniSwitch user guides:
• OmniSwitch 6600 Family Getting Started Guide
Describes the hardware and software procedures for getting an OmniSwitch 6624 or 6648 up and
running. Also provides information on fundamental aspects of OmniSwitch software and stacking
architecture.
• OmniSwitch 6800 Series Getting Started Guide
Describes the hardware and software procedures for getting an OmniSwitch 6800 up and running. Also
provides information on fundamental aspects of OmniSwitch software and stacking architecture.
• OmniSwitch 7700/7800 Getting Started Guide
Describes the hardware and software procedures for getting an OmniSwitch 7700 or 7800 up and
running. Also provides information on fundamental aspects of OmniSwitch software architecture.
• OmniSwitch 8800 Getting Started Guide
Describes the hardware and software procedures for getting an OmniSwitch 8800 up and running. Also
provides information on fundamental aspects of OmniSwitch software architecture.
• OmniSwitch 6600 Family Hardware Users Guide
Complete technical specifications and procedures for all OmniSwitch 6624 and 6648 chassis, power
supplies, fans, uplink modules, and stacking modules.
OmniSwitch Troubleshooting Guide September 2005
page -xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
• OmniSwitch 6800 Series Hardware Users Guide
Complete technical specifications and procedures for all OmniSwitch 6800 chassis, power supplies,
fans, uplink modules, and stacking modules.
• OmniSwitch 7700/7800 Hardware Users Guide
Complete technical specifications and procedures for all OmniSwitch 7700 and 7800 chassis, power
supplies, fans, and Network Interface (NI) modules.
• OmniSwitch 8800 Hardware Users Guide
Complete technical specifications and procedures for all OmniSwitch 8800 chassis, power supplies,
fans, and Network Interface (NI) modules.
• OmniSwitch CLI Reference Guide
Complete reference to all CLI commands supported on the OmniSwitch 6624/6648, 7700/7800, and
8800. Includes syntax definitions, default values, examples, usage guidelines and CLI-to-MIB variable
mappings.
• OmniSwitch 6600 Family Switch Management Guide
Includes procedures for readying an individual switch for integration into a network. Topics include the
software directory architecture, image rollback protections, authenticated switch access, managing
switch files, system configuration, using SNMP, and using web management software (WebView).
• OmniSwitch 6800 Series Switch Management Guide
Includes procedures for readying an individual switch for integration into a network. Topics include the
software directory architecture, image rollback protections, authenticated switch access, managing
switch files, system configuration, using SNMP, and using web management software (WebView).
• OmniSwitch 7700/7800/8800 Switch Management Guide
Includes procedures for readying an individual switch for integration into a network. Topics include the
software directory architecture, image rollback protections, authenticated switch access, managing
switch files, system configuration, using SNMP, and using web management software (WebView).
• OmniSwitch 6600 Family Network Configuration Guide
Includes network configuration procedures and descriptive information on all the major software
features and protocols included in the base software package. Chapters cover Layer 2 information
(Ethernet and VLAN configuration), Layer 3 information (RIP and static routes), security options
(authenticated VLANs), Quality of Service (QoS), and link aggregation.
• OmniSwitch 6800 Series Network Configuration Guide
Includes network configuration procedures and descriptive information on all the major software
features and protocols included in the base software package. Chapters cover Layer 2 information
(Ethernet and VLAN configuration), Layer 3 information (RIP and static routes), security options
(authenticated VLANs), Quality of Service (QoS), and link aggregation.
page -xviii
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
• OmniSwitch 7700/7800/8800 Network Configuration Guide
Includes network configuration procedures and descriptive information on all the major software
features and protocols included in the base software package. Chapters cover Layer 2 information
(Ethernet and VLAN configuration), Layer 3 information (routing protocols, such as RIP and IPX),
security options (authenticated VLANs), Quality of Service (QoS), link aggregation, and server load
balancing.
• OmniSwitch 6600 Family Advanced Routing Configuration Guide
Includes network configuration procedures and descriptive information on the software features
included in the advanced routing software package (OSPF).
• OmniSwitch 6800 Series Advanced Routing Configuration Guide
Includes network configuration procedures and descriptive information on the software features and
protocols included in the advanced routing software package (OSPF, DVMRP, PIM-SM).
• OmniSwitch 7700/7800/8800 Advanced Routing Configuration Guide
Includes network configuration procedures and descriptive information on all the software features and
protocols included in the advanced routing software package. Chapters cover multicast routing
(DVMRP and PIM-SM) and OSPF.
• Technical Tips, Field Notices
Includes information published by Alcatel’s Service and Support group.
• Release Notes
Includes critical Open Problem Reports, feature exceptions, and other important information on the
features supported in the current release and any limitations to their support.
These user guides are included on the Alcatel Enterprise User Manual CD that ships with every switch.
You can also download these guides at http://www.ind.alcatel.com/library/manuals/index.cfm?cnt=index.
OmniSwitch Troubleshooting Guide September 2005
page -xix
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Calling Alcatel’s Technical Assistance
Center
Before calling Alcatel’s Technical Assistance Center (TAC), make sure that you have read through the
appropriate section (or sections) and have completed the actions suggested for your system’s problem.
Additionally, do the following and document the results so that the Alcatel TAC can better assist you:
• Have a network diagram ready. Make sure that relevant information is listed, such as all IP addresses
and their associated network masks.
• Have any information that you gathered while troubleshooting the issue to this point available to
provide to the TAC engineer.
• If the problem appears to be with only a few-fewer than four-switches, capture the output from the
When calling Alcatel TAC in order to troubleshoot or report a problem following information can be help-
ful to get a quick resolution:
• All the dump files that were created, if any
• Output of switch log or the switch log files swlog1.log and swlog2.log
• Configuration file boot.cfg
• A capture of the show microcode command
• A capture of the show module long command
• If a CMM fail over to the redundant CMM happened because of this failure then include this informa-
tion from both of the CMMs.
Dial-in or Telnet access can also helpful for effective problem resolution.
page -xx
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Troubleshooting the Switch
System
In order to troubleshoot the system, a basic understanding of the operation of Chassis Management
Modules (CMMs) and their interaction with Network Interface (NI) modules is required. Some concepts
are covered in this chapter:
• Understanding of the “Diagnosing Switch Problems” chapter in the appropriate OmniSwitch Switch
Management Guide.
• Understanding of the “Using Switch Logging” from the appropriate OmniSwitch Network Configura-
tion Guide is highly recommended.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Troubleshooting the Switch System
Introduction
The CMM is the Management Module of the switch. All of the critical operations of the switch including
the monitoring is the responsibility of the CMM. CMM not only provides monitoring but also synchro-
nizes all of the NI for different operations. The operation of the CMM is the same in OS-6/7/8XXX
switches. The only difference is that OS-6/7XXX has the switching fabric inherent to the module whereas
OS-8800 has fabric at the back of the chassis.
NI has a build in CPU. Each NI has its own CPU, which acts independently of the CMM. The CPU of the
NI has to interact with the CPU on the CMM for certain operations. If this operation becomes out of sync
then it can create problems specific to that NI.
In order to troubleshoot the system, an understanding of the CMM and NI operation is essential.
page 1-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Troubleshooting System for OS-6624/6648 and OS-7/8XXX
Troubleshooting System for OS-6624/6648 and
OS-7/8XXX
If the switch is having any problems the first place to look for is the CMM. All the task are supervised by
CMM. Any in coherency between CMM and the NI can cause problems to appear.
1 The first step for troubleshooting problems with the switch is to look at the overall general health of the
switch.
OmniSwitch 7700/7800/8800
Verify that all of the modules in the chassis are up and operational, using the command:
-> show module status
Operational
Slot Status
Firmware
Admin-Status Rev
MAC
------+-------------+------------+---------+-----------------
CMM-A
NI-1
NI-3
NI-5
UP
UP
UP
UP
POWER ON
POWER ON
POWER ON
POWER ON
36
00:d0:95:6b:09:40
00:d0:95:6b:22:5c
00:d0:95:6b:23:2e
00:d0:95:6b:3a:20
5
5
5
OmniSwitch 6624/6648
If the switch is having any problems the first place to look for is the CMM. All the task are supervised by
CMM. Any in coherency between CMM and the NI can cause problems to appear. For OS-6600 with 8
units stacked together, the CMM will be:
• Primary
• Secondary
• Idle
The switch with the lowest ID will become the primary CMM.
The first step for troubleshooting problems with the switch is to look at the overall general health of the
switch.
Verify that all of the modules in the chassis are up and operational, using the command:
-> show module status
Operational
Status
Firmware
Admin-Status Rev
Slot
MAC
------+-------------+------------+---------+-----------------
CMM-1
CMM-2
NI-1
UP
POWER ON
POWER ON
POWER ON
N/A
N/A
N/A
00:d0:95:84:4b:d2
00:d0:95:84:4b:d2
00:d0:95:84:4b:d4
SECONDARY
UP
OmniSwitch Troubleshooting Guide September 2005
page 1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting System for OS-6624/6648 and OS-7/8XXX
Troubleshooting the Switch System
NI-2
NI-3
NI-4
NI-5
NI-6
NI-7
NI-8
UP
UP
UP
UP
UP
UP
UP
POWER ON
POWER ON
POWER ON
POWER ON
POWER ON
POWER ON
POWER ON
N/A
N/A
N/A
N/A
N/A
N/A
N/A
00:d0:95:84:3d:26
00:d0:95:86:50:f4
00:d0:95:84:49:be
00:d0:95:84:39:be
00:d0:95:84:4a:90
00:d0:95:84:39:f4
00:d0:95:84:3c:44
OmniSwitch 6600 with 8 stackable switches show up. Notice that the switch with ID 1 is the primary
CMM and the switch with ID of 2 is the secondary. All the switch also show up as NI because each switch
has a CPU and is also a NI.
To verify the stacking topology, use the following command:
-> show stack topology
Link A
State
Link A
Link A
Link B
Link B
RemoteNI RemoteLink
Link B
NI
Role
RemoteNI RemoteLink State
---+-----------+---------+---------+-----------+---------+---------+----------
1 PRIMARY
2 SECONDARY
3 IDLE
4 IDLE
5 IDLE
6 IDLE
7 IDLE
8 IDLE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
8
3
2
5
4
7
6
1
51
27
51
51
51
51
51
51
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
2
1
4
3
6
5
8
7
52
52
52
28
52
52
52
2
The above command shows the stacking topology. Switch 1 is the primary connected to Switch 8 on port
51 and Switch 2 on port 52. The state of CPUs for all the switches in the stack is shown by the output of
this command.
2 Verify the power supply (or supplies).
OmniSwitch 7700/7800/8800
Omni Switch 7/8XXX has build-in mechanism to power off the modules if the power supply is not
enough. Switching off a power supply in a chassis which does not have redundant power supply will result
in power off of the modules. Make sure that there is no power involvement.
Check the power supply status, using the command:
-> show power supply 1
Module in slot PS-1
Model Name:
Description:
Part Number:
OSR-PS-06,
OSR-PS-06,
901750-10,
page 1-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Troubleshooting System for OS-6624/6648 and OS-7/8XXX
Hardware Revision:
Serial Number:
,
B42N101P2,
Manufacture Date:
Firmware Version:
Admin Status:
OCT 18 2001,
,
POWER ON,
UP
Operational Status:
Make sure that all the known good power supplies are operational.
OmniSwitch 6624/6648
Check the power supply status, using the command:
-> show power supply
Power Supplies in chassis 1
PS
Operational Status
-----+-------------------
PS-1 UP
PS-2
NOT PRESENT
Power Supplies in chassis 2
PS Operational Status
-----+-------------------
PS-1 UP
PS-2
NOT PRESENT
Power Supplies in chassis 3
PS Operational Status
-----+-------------------
PS-1 UP
PS-2
NOT PRESENT
Power Supplies in chassis 4
PS Operational Status
-----+-------------------
PS-1 UP
PS-2
NOT PRESENT
Power Supplies in chassis 5
PS Operational Status
-----+-------------------
PS-1 UP
PS-2
NOT PRESENT
Power Supplies in chassis 6
PS Operational Status
-----+-------------------
PS-1 UP
PS-2
NOT PRESENT
Power Supplies in chassis 7
PS Operational Status
-----+-------------------
PS-1 UP
PS-2
NOT PRESENT
OmniSwitch Troubleshooting Guide September 2005
page 1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting System for OS-6624/6648 and OS-7/8XXX
Troubleshooting the Switch System
Power Supplies in chassis 8
PS
Operational Status
-----+-------------------
PS-1 UP
PS-2
NOT PRESENT
Make sure that all the known good power supplies are operational.
3 Verify the CPU utilization.
OmniSwitch 6624/6648 and 7700/7800/8800
The CPU utilization of CMM can be viewed by using the command:
-> show health
* - current value exceeds threshold
Device
Resources
Min 1 Hr 1 Hr
Limit Curr Avg Avg Max
----------------+-------+-----+------+-----+-----+-------
Receive
Transmit/Receive
Memory
80 00
80 00
80 43
80 02
50 38
50 32
00
00
43
06
37
32
00
00
43
05
37
31
0
00
43
07
37
32
Cpu
Temperature Cmm
Temperature Cmm Cpu
The above command shows the receive, transmit/receive, memory, CPU, temperature CMM and tempera-
ture CMM CPU statistics for current, 1 minimum average, 1 hour average and 1 hour maximum. All the
values should be within the threshold. Anything above the threshold depicts that some abnormal behavior.
Normally 1 hour average maximum might be high if the switch was booted up in the last hour but it should
be fairly steady during normal operation.
If none of the above are above the threshold then the next step is to try to isolate the problem to a particu-
lar NI. Due to the distributed architecture every NI has it own CPU to perform some operations locally. It
is possible that a particular NI might be at high CPU utilization at a time when other NI as well as the CPU
are within the thresholds.
If none of the above are above the threshold then the next step is to try to isolate the problem to a particu-
lar NI (or a switch within an OmniSwitch 6624/6648 stack) with the show health slot_number CLI
command:
-> show health 5
* - current value exceeds threshold
Slot 05
Resources
1 Min 1 Hr 1 Hr
Limit Curr Avg Avg Max
----------------+-------+-----+------+-----+-----+-------
Receive
Transmit/Receive
Memory
80 01
80 01
80 39
80 21
01
01
39
22
01
01
39
21
01
01
39
24
Cpu
The principle for the health of an NI is the same as for CMM.
page 1-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Troubleshooting System for OS-6624/6648 and OS-7/8XXX
The average on one minute is calculated from the average of 12 samples. Each sample is an average of the
CPU utilization during 5 seconds. Those values are stored in a table. The current minute (1 Min Avg or
“min”) displays the average of the last 12 samples.
Every 60 seconds the average of the 12 samples is recorded into the average value for this minute. Those
values are stored in a form of 60 samples which represent one hour.
Most probably one of the above would help to localize the problem to a particular NI or to CMM. For
more details see, Section “Monitoring Switch Health” in the chapter titled “Diagnosing Switch Problems”
in the appropriate OmniSwitch Network Configuration Guide.
4 Check the switch log.
OmniSwitch 6624/6648 and 7700/7800/8800
Now, one of the most important things to check is the switch log. Switch log would contain the error
messages depending on the settings of the log levels and applications configured to generate error
messages. Default settings of the log switch log can be view using the command:
-> show swlog
Switch Logging is:
- INITIALIZED
- RUNNING
Log Device(s)
----------------
flash
console
Only Applications not at the level ‘info’ (6) are shown
Application ID
----------------------------
CHASSIS (64) debug3 (9)
Level
By default, log devices are set to be flash and console. This can be changed and specific log servers can be
used to log the messages, please refer to the Switch Management Guide for further details. The applica-
tion trace level is set for ‘info’. Any error messages or informational messages would be logged in the
switch log.
Switch log should be viewed to see if any errors messages were generated by the switch. The command to
use is:
-> show log swlog
Displaying file contents for 'swlog2.log'
FILEID: fileName[swlog2.log], endPtr[32]
configSize[64000], currentSize[64000], mode[2]
Displaying file contents for 'swlog1.log'
FILEID: fileName[swlog1.log], endPtr[395]
configSize[64000], currentSize[64000], mode[1]
Time Stamp
Application
Level Log Message
------------------------+--------------+-------+--------------------------------
MON AUG 21 23:09:57 2023 HSM-CHASSIS info == HSM == GBIC extraction detect
ed on NI slot 1, GBIC port 2
MON AUG 21 23:28:33 2023 HSM-CHASSIS info == HSM == GBIC Insertion detecte
d on NI slot 1, GBIC port 1
MON AUG 21 23:28:33 2023 HSM-CHASSIS info == HSM == GBIC Insertion detecte
OmniSwitch Troubleshooting Guide September 2005
page 1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting System for OS-6624/6648 and OS-7/8XXX
Troubleshooting the Switch System
d on NI slot 1, GBIC port 2
MON AUG 21 23:28:39 2023 HSM-CHASSIS info == HSM == GBIC extraction detect
ed on NI slot 5, GBIC port 2
MON AUG 21 23:30:39 2023 HSM-CHASSIS info == HSM == GBIC Insertion detecte
d on NI slot 5, GBIC port 2
MON AUG 21 23:30:41 2023 HSM-CHASSIS info == HSM == GBIC extraction detect
ed on NI slot 1, GBIC port 1
MON AUG 21 23:30:45 2023 HSM-CHASSIS info == HSM == GBIC extraction detect
ed on NI slot 1, GBIC port 2
TUE AUG 22 00:05:45 2023 CSM-CHASSIS info == CSM == !!!ACTIVATING!!!
TUE AUG 22 00:05:45 2023 CSM-CHASSIS info == CSM == !!! REBOOT !!!
TUE AUG 22 00:05:53 2023
restart type=0x2 (COLD)
SYSTEM alarm System rebooted via ssReboot(),
The log message are kept in two log files: swlog1.log and swlog2.log in flash. In the above example, log
messages show that some GBICs were extracted and inserted at a particular time. In addition, the switch
was rebooted. This information helps to relate the time of the problem together with the events happening
at the switch. In addition, it also provides an idea about if the source of the problem was external or inter-
nal to the switch.
If the log messages do not show enough information then they can be changed for specific applications to
a higher log level or for all the applications running in the switch. For setting up different log levels in
switch log, please refer to the “Using Switch Logging” chapter in the appropriate OmniSwitch Network
Configuration Guide.
If the switch is running in redundant configuration make sure that the two CMMs are completely synchro-
nized. This can be done using the command:
-> show running-directory
Running CMM
: PRIMARY,
Running configuration : WORKING,
Certify/Restore Status : CERTIFIED,
Synchronization Status : SYNCHRONIZED
If the two CMMs are not synchronized and the problem leads to the failure of Primary CMM then it will
result in re-initialization of all of the modules. If the two CMMs are properly synchronized and primary
CMM failed, the take over mechanism will be transparent to the end user. So, for complete redundancy
keep the two CMMs synchronized.
Look for any post-mortem dump files that may be created due to the problem with the switch. Post
Mortem Dump files have an extension of *.dmp and are created in /flash directory of the CMM (be sure to
check the secondary CMM, if running in redundant mode). System dump files are normally named as
“cs_system.dmp”, Memory related dump files are normally created as “MemMon000.dmp” and NI related
dump files are named as “SloXSliYver1.dmp”, where X is the slot number and Y is the slice number.
The creation of a dump file indicates a problem with the switch. System related dump files can be viewed
through CLI but other dump files cannot. For system related dump files use the command:
-> show log pmd cs_system.pmd
Capture the output of this command. In addition, if there are any dump files created in the switch, they
should be downloaded through FTP to forward them to technical support. Technical Support can have
them analyzed to find the source of the problem.
page 1-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Advanced Troubleshooting
Advanced Troubleshooting
One level of switch logging is stored in the two log files located in the /flash directory. There is another
low level debug that can be enabled and used for diagnosing the problems. This debug is known as
“systrace”, meaning system trace. The information in this trace is stored in NVRAM on the CMM, so it is
valid until powered off. Soft reboot of the switch will retain the trace information but powering off the
switch will result in loosing all of the information. This is less CMM intensive so can be used to collect all
the background information about the different tasks running in the switch.
The command to look at the default settings for systrace is
-> debug systrace show
sysTrace is:
- INITIALIZED
- RUNNING
- configured to TRACE CALLERS
- configured to NOT WATCH on stdout
All Applications have their trace level set to level ’info’ (6)
Systrace is set for the level of “info” for all the applications. Any application with trace level other than 6
is displayed in the above command output. Notice that it is initialized by default and is running in the
background. By default it is configured not to display messages on the console. The purpose of systrace is
to track all the system processes called and the caller.
Application log levels can be changed and specific applications can also be set for the logging purposes.
The commands are similar to switch log.
-> debug systrace appid ?
WEB VRRP VLAN TRAP TELNET SYSTEM STP SSL SSH
SNMP SMNI SLB SESSION RSVP RMON QOS QDRIVER
QDISPATCHER PSM PRB-CHASSIS PORT-MGR POLICY PMM
NOSNMP NI-SUPERVISION NI-INTERFACE NAN-DRIVER
MODULE MIPGW LINKAGG LDAP IPX IPMS IPC-MON
IPC-LINK IPC-DIAG IP-HELPER IP INTERFACE
HSM-CHASSIS HEALTH GMAP GM FTP EPILOGUE EIPC
DRC DISTRIB DIAG CVM-CHASSIS CSM-CHASSIS CONFIG
CMS-CHASSIS CMM-INTERFACE CLI CHASSIS
CCM-CHASSIS BRIDGE AMAP ALL AAA 802.1Q <num>
(System Service & File Mgmt Command Set)
The applications and the log levels are the same as switch log applications. Please refer to the “Section
Switch Logging Commands Overview” section in the “Using Switch Logging” chapter in the appropriate
OmniSwitch Network Configuration Guide.
Systrace can be enabled using the command:
-> debug systrace enable
To look at the systrace log file use the following command:
swnygb02 > debug systrace show log
TStamp(us) AppId Level Task
Comment
----------+------+------+----------+---------------------------------------
3349119104 CSM-CH info tCsCSMtask ***HELLO FSM TRACE***
3349118980 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> Event = CS_CSM_HELLO
OmniSwitch Troubleshooting Guide September 2005
page 1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Troubleshooting
Troubleshooting the Switch System
_SM_IPCUP_TIMEOUT
3349118948 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> CS_TIMEOUT
3345200526 CSM-CH info tCsCSMtask ***HELLO FSM TRACE***
3342928783 CSM-CH info tCsCSMtask ***HELLO FSM TRACE***
3342928661 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> Event = CS_CSM_HELLO
_SM_IPCUP_TIMEOUT
3342928628 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> CS_TIMEOUT
3336738410 CSM-CH info tCsCSMtask ***HELLO FSM TRACE***
3336738287 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> Event = CS_CSM_HELLO
_SM_IPCUP_TIMEOUT
3336738256 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> CS_TIMEOUT
3334849145 CSM-CH info tCsCSMtask ***HELLO FSM TRACE***
3330548020 CSM-CH info tCsCSMtask ***HELLO FSM TRACE***
3330547902 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> Event = CS_CSM_HELLO
_SM_IPCUP_TIMEOUT
3330547869 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> CS_TIMEOUT
3324495309 CSM-CH info tCsCSMtask ***HELLO FSM TRACE***
3324357940 CSM-CH info tCsCSMtask ***HELLO FSM TRACE***
3324357816 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> Event = CS_CSM_HELLO
_SM_IPCUP_TIMEOUT
3324357782 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> CS_TIMEOUT
3318167293 CSM-CH info tCsCSMtask ***HELLO FSM TRACE***
3318167171 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> Event = CS_CSM_HELLO
_SM_IPCUP_TIMEOUT
3318167139 CSM-CH info tCsCSMtask csCsmHelloReceptio - -> CS_TIMEOUT
This information is useful to analyze the different processes taking place in the switch.
Other useful command to use in case of problem is:
-> show tech-support
This command captures all of the information from the chassis, including the hardware information,
configuration, software release active and some other statistics about the number of buffers being used at
the time of the use of command. The output of the command is saved in /flash as “tech_support.log”.
Other variation of this command is:
-> show tech-support layer2
This command collects Layer 2 data only.
-> show tech-support layer3
This command collects Layer 3 data only.
page 1-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Dshell Troubleshooting
Dshell Troubleshooting
To further diagnose the task consuming the CPU on the CMM one needs to use the following Dshell
commands:
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
Working: [Kernel]->spyReport
NAME
ENTRY
TID PRI total % (ticks) delta % (ticks)
----- --- --------------- ---------------
--------
tExcTask
tLogTask
tShell
tWdbTask
IPC_tick
tSpyTask
--------
excTask
logTask
shell
7545100
753f800
41b1600
73ae6a0
6862660
0
0
1
3
4
5
0% (
0% (
0% (
0% (
179)
0)
25)
0)
0% (
0% (
1% (
0% (
0% (
0% (
0% (
0% (
0)
0)
1)
0)
0)
0)
0)
0)
7)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
IPC_tick
spyComTask 41aab10
6% ( 11855)
0% (
0% (
0% (
1% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0)
0)
0)
tAioIoTask1 aioIoTask 7528580 50
tAioIoTask0 aioIoTask 75212d0 50
tNetTask
tIpedrMsg
tAioWait
bbussIntMoni tBbusIntMo 6864a00 70
ipc_monitor ipc_monito 67ff4a0 70
tL2Stat
Gateway
EIpc
netTask
ipedrKerne 53043b0 50
aioWaitTas 752f830 51
741c820 50
2047) 10% (
25)
0)
0)
10)
701)
2)
0)
124)
0)
19)
18)
132)
0)
438)
207)
0)
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
esmStatMsg 57626b0 70
mipGateway 67e1770 80
eipcMgr_ma 678ac10 80
EsmDrv
esmDrv
579f990 80
tMemMon
tCS_PTB
tCS_CCM
tCS_PRB
tCS_CMS
tCS_HSM
tCsCSMtask Letext
tNanISR
SwLogging
DSTwatcher dstWatcher 7214f00 100
tWhirlpool batch_entr 71fb210 100
ipc_tests
PortMgr
PsMgr
VlanMgr
TrapMgr
PartMgr
SNMPagt
SesMgr
SsApp
memMonTask 7230d60 90
csPtbMain 67ee930 93
csCcmMain 722d590 93
csPrbMain 72299f0 93
csCmsMain 7227720 93
Letext
7225420 93
67f3c10 94
nanProcInt 4ae2660 95
swLogTask 724b900 100
4)
0)
4)
3)
6)
0)
ipc_tests_ 67fd1f0 100
pmMain
psm_main
Letext
trap_task 6774fc0 100
partm_eup_ 675fcf0 100
snmp_task 6980d70 100
sesmgr_mai 697b8a0 100
tssAppMain 59126b0 100
67df2f0 100
67d9030 100
678f1d0 100
292)
10)
0)
93)
1)
11)
38)
0)
414)
7)
Ftpd
cmmFtpd
58f3a80 100
NanDrvr
Health
L3Hre
DbgNiGw
SrcLrn
nanDriver 58da2b0 100
healthMonM 58d7b70 100
l3hre_cmm_ 58709d0 100
dbgGw_main 585f170 100
slCmmMain 5798ab0 100
0)
91)
OmniSwitch Troubleshooting Guide September 2005
page 1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting the Switch System
GrpMob
Stp
8021q
LnkAgg
gmcControl 5793320 100
stpCMM_mai 56b3eb0 100
main_8021q 5841290 100
la_cmm_mai 543dbc0 100
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
3% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
1% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
3% (
0% (
80)
82)
0)
57)
70)
924)
164)
3)
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0)
0)
0)
0)
0)
0)
0)
0)
17)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
6)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
11)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0)
0
tSlcMsgHdl slcMsgProc 54397f0 100
AmapMgr
GmapMgr
PMirMon
Ipedr
xmap_main_ 53f0140 100
gmap_main_ 535c750 100
pmmMain
ipedrMain 5327730 100
aaa_main 5324110 100
5340e20 100
6664) 26% (
AAA
152)
27)
0)
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
9% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
stpTick
tIpedrPkt
AVLAN
onex
Ipmem
stpcmm_tim 5316800 100
ipedrPktDu 52f3d90 100
aaaAvlanMa 5256670 100
onex_main 52513e0 100
ipmem_main 522fad0 100
7)
15)
398)
19)
23)
24)
41)
1318)
804)
36)
3)
la_cmm_tick la_cmm_tic 522b370 100
ipmfm
ipmpm
Ipx
Vrrp
UdpRly
Qos
PolMgr
SlbCtrl
WebView
SNMP GTW
ipmfm_main 51e7cc0 100
ipmpm_main 58b99e0 100
ipxMain
vrrpMain
4fbd180 100
4fba330 100
udpRlyMain 4f926d0 100
qos_main 4f70ac0 100
pyPolicyMa 4e7cdb0 100
slbcMain
tEmWeb
4e787f0 100
4e74000 100
4)
2)
1)
2)
snmp_udp_g 4add0a0 100
SNMP TIMER snmp_timer 4ada6e0 100
GmapTimer
DrcTm
tDrcIprm
tOspf
tPimsm
gmap_proc_ 4ad7080 100
2)
tmMain
iprmMain
ospfMain
4acf630 100
499bba0 100
4898d60 100
28)
336)
3419) 16% (
371)
66)
0)
pimsmMain 46d39e0 100
ipmrmMain 46132e0 100
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
0% (
tDrcIpmrm
cliConsole clishell_m 44b3b00 100
tWebTimer web_timer 4b7e520 107
tssApp_SNMP_ tssAppChil 58fbbf0 110
tssApp_3_4 tssAppChil 4251500 110
CfgMgr
tCS_CCM2
Sshd
Telnetd
Rmon
2)
0)
0)
confMain
csCcmChild 4ae03b0 130
cmmsshd 5b38d50 150
cmmtelnetd 590d420 150
rmonMain 5873ff0 150
csCvmMain 72194a0 200
67ec480 120
455)
0)
0)
13)
86)
0)
0)
8)
0)
0)
0)
0)
tCS_CVM
SmNiMgr
tIpxTimer
smNiTask
ipxTimer
586e060 200
4f83f90 200
tIpxGapper ipxGapper 4f7b1c0 200
SesMon_3 Letext 429ef90 200
tTelnetOut0 cmmtelnetO 429c5d0 200
tTelnetIn0 cmmtelnetI 42652e0 200
0)
0)
0)
0)
0)
0)
0)
15)
0)
8)
65)
CliShell0
clishell_m 42611b0 200
0)
1)
41)
tPolMonSvr pyMonitorM 4e45ae0 210
tDcacheUpd dcacheUpd 74f8e70 250
KERNEL
INTERRUPT
IDLE
6051) 23% (
19) 0% (
79% ( 154794) 12% (
93% ( 193565) 97% (
TOTAL
page 1-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Dshell Troubleshooting
2 tasks were created.
2 tasks were deleted.
spyStop
value = 0 = 0x0
It seems that the CPU task is high because of tNetTask, Ipedr, and tOSPF.
Check to see if any of the task is suspended on the CMM.
Working: [Kernel]->i
NAME
ENTRY
TID
PRI STATUS
PC
SP
ERRNO DELAY
---------- ------------ -------- --- ---------- -------- -------- ------- -----
tExcTask excTask
tLogTask logTask
7545100 0 PEND
753f800 0 PEND
41b1600 1 READY
73ae6a0 3 PEND
6862660 4 READY
499bba0 100 PEND+T
4898d60 100 SUSPEND
17fd68 7544d40 3d0001
17fd68 753f430
15c0e0 41b09a0 30065
0
0
0
0
0
0
tShell
shell
tWdbTask 150520
IPC_tick IPC_tick
tDrcIprm iprmMain
158540 73ae130
158540 6862340
158540 499b520
158540 48986d0
0
0
b 243
b 299
tOspf
ospfMain
value = 0 = 0x0
Working: [Kernel]->
In the above example, the OSPF task is suspended. Typically when a task is suspended, the system will
automatically reboot and generate a system dump file. In the event that the system does not reboot, then
try to gather the task trace and memory dump for that specific task using the following command:
Working: [Kernel]->tt 0x4898d60
108e9c vxTaskEntry +c : Letext (&dataInfo, 67f3920, 67f3a20, 34000000, 66ff800,
6a69800)
66b69b4 Letext +2d4: zcSelect (5, 67f3a20, 0, 0, 6a6c800, 247)
6ff56f8 zcSelect +458: semTake (67eedc0, ffffffff, a, 28, a, 0)
158b4c semTake +2c : semBTake (67eedc0, ffffffff, &semTakeTbl, 0, &semBTake,
264c00)
value = 0 = 0x0
Working: [Kernel]->ti 0x4898d60
NAME
---------- ------------ -------- --- ---------- -------- -------- ------- -----
tOspf ospfMain 4898d60 100 SUSPEND 13e060 490f920
ENTRY
TID
PRI STATUS
PC
SP
ERRNO DELAY
b
0
stack: base 0x49103d0 end 0x49009d0 size 63312 high 10036 margin 53276
options: 0x4
VX_DEALLOC_STACK
%pc = 13e060 %npc = 13e064 %ccr =
0 %y
0 %tl =
=
0
0
%asi =
%pil =
%g0 =
%g3 =
%g6 =
%i1 =
%i4 =
%i7 =
%l2 =
%l5 =
0 %cwp =
0 %pstate =
0 %tt =
1e
0 %g1 =
0 %g2 =
0
0
0
0
0 %g4 =
0 %g7 =
0 %i2 =
0 %i5 =
0 %l0 =
0 %l3 =
0 %l6 =
0 %g5 =
0 %i0 =
0 %i3 =
0 %fp =
0 %l1 =
0 %l4 =
0 %l7 =
490f9e0
0
0
0
OmniSwitch Troubleshooting Guide September 2005
page 1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting the Switch System
%o0 =
%o3 =
%sp =
490f9e0 %o1 =
0 %o4 =
490f920 %o7 =
0 %o2 =
0 %o5 =
0
0
0
value = 76612560 = 0x49103d0
Certified: [Kernel]->
To troubleshoot a CPU or memory spike with 5.1.5.X, you can start a software routine in dshell and it will
log the task name to the swlog whenever there is a spike in CPU or memory usage.
Switch/> dshell
Certified: [Kernel]->lkup "Hog"
catchCpuHog
catchMemHog
releaseCpuHog
releaseMemHog
0x00152700 text
0x0013fa80 text
0x00152720 text
0x0013fb60 text
=> to turn on CPU watch
=> to turn on Memory watch
=> to turn off CPU watch
=> to turn off Memory watch
value = 58685232 = 0x37f7730
Certified: [Kernel]->
To troubleshoot a problem related to stack overflow:
Working: [Kernel]->checkStack
NAME
ENTRY
TID
SIZE CUR HIGH MARGIN
------------ ------------ -------- ----- ----- ----- ------
tExcTask
tLogTask
excTask
logTask
7525070 19992 960 4344 15648
751f750 8184 976 2176 6008
tPingTmo854 0x0000103d60 3d9c580 8184 800 1068 7116
tShell
tWdbTask
IPC_tick
shell
0x0000168200 7395dc0 7904 1392 2060 5844
IPC_tick 6efb040 32760 800 4952 27808
3c13ef0 19048 6368 8644 10404
tCsCSMtask2 csCsmHelloBa 7214c40 19992 1200 4264 15728
tCS_PTB
tCS_CCM
tCS_PRB
tCS_CMS
tCS_HSM
csPtbMain
csCcmMain
csPrbMain
csCmsMain
csHsmMain
5ca5960 8184 800 5152 3032
720f8e0 13312 1632 9436 3876
720bc50 9320 1504 5588 3732
7209240 8176 1872 3044 5132
7206f20 29320 1472 7556 21764
5cb2240 29320 2304 14516 14804
tCsCSMtask csCsmMain
tCsCSMtask3 csCsmChecksu 5caaa40 19984 848 6724 13260
tAioIoTask1 aioIoTask
tAioIoTask0 aioIoTask
7508450 28664 944 1136 27528
7501180 28656 944 1136 27520
74040a0 14992 944 5204 9788
tNetTask
tIpedrMsg
tTrapPing
netTask
ipedrKernelM 4d4a7a0 19984 944 2828 17156
0x0005b89e60 3aa7830 19984 2864 3172 16812
OmniSwitch 7700/7800/8800 Dshell Task Definitions
tExcTask
tLogTask
tShell
Exception Handling Task
Log Task
Shell Task
tWdbTask
IPC_tick
tSpyTask
tAioIoTask1
Wind Debug Agent
IPC ticks
Spy Task monitor the system utilization
Asynchronous I/O Support
page 1-14
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Dshell Troubleshooting
tAioIoTask0
tNetTask
tIpedrMsg
tAioWait
bbussIntMoni
ipc_monitor
tL2Stat
Asynchronous I/O Support
Routing Task
IP Ethernet Driver Message Handle Task
Asynchronous I/O Support
BBUS monitor Task
IPC monitor Task
L2 statistics gathering task
Management Information Protocol Gateway
Extended IPC task
Gateway
EIpc
EsmDrv
Ethernet switching manager Driver Task
Memory Monitor Task
tMemMon
tCS_PTB
tCS_CCM
tCS_PRB
tCS_CMS
tCS_HSM
tCsCSMtask
tNanISR
SwLogging
DSTwatcher
tWhirlpool
ipc_tests
Chassis Supervision Pass-through Support
Chassis Configuration Manager
Chassis Supervision Prober Task
Chassis MAC Server
Chassis Supervision Hardware Services Manager
Chassis Supervision Chassis State Manager
Nantucket Interrupt Service Routine
Switch Logging Task
Clock Task of the switch
Encryption Support
IPC debugging and test support
Port Manager Task
PortMgr
PsMgr
Power Supply Manager Task
VLAN Manager Task
VlanMgr
TrapMgr
PartMgr
SNMPagt
SesMgr
Trap Manager Task
Partition management task
SNMP agent task
Session Manager Task
SsApp
Session Application Task
FTP Daemon Task
Ftpd
NanDrvr
Nantucket Driver Task
OmniSwitch Troubleshooting Guide September 2005
page 1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting the Switch System
Health
Health Task
L3Hre
Layer 3 HRE Task
DbgNiGw
SrcLrn
NI Debug support
Source Learning Task
Group Mobility Task
Spanning Tree Task
802.1Q Task
GrpMob
Stp
8021q
LnkAgg
tSlcMsgHdl
AmapMgr
GmapMgr
PMirMon
Ipedr
Link Aggregation Task
Source Learning Message Handler Task
AMAP Manager Task
GMAP Manager Task
Port Mirror Monitoring Task
IP Extended Dynamic Routing Task
AAA task
AAA
stpTick
tIpedrPkt
AVLAN
onex
STP Timing Task
IP Ethernet Driver Task
Authenticated VLAN Task
802.1X Task
Ipmem
IP Multicast Task
la_cmm_tick
ipmfm
CMM Link Aggregation Timer
IP Multicast Forwarding
IP Multicast Management
IPX Task
ipmpm
Ipx
Vrrp
VRRP Task
UdpRly
Qos
UDP Relay Task
QOS Task
PolMgr
SlbCtrl
WebView
SNMP GTW
SNMP TIMER
GmapTimer
Policy Manager Task
Server Load Balancing Control Task
WebView Task
SNMP Gateway
SNMP Timer
GMAP Timer Task
page 1-16
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Dshell Troubleshooting
DrcTm
Dynamic Routing Control Timer Task
tDrcIprm
tOspf
Dynamic Routing Control Task for IP Route Manager
OSPF Task
tPimsm
PIM SIM Task
tDrcIprm
cliConsole
tWebTimer
tssApp_SNMP
tssApp_3_4
CfgMgr
Dynamic Routing Control IP Route Manager task
CLI Console Task
Web Session Timer
Temporary System Services task to support SNMP
Temporary System Services task to support CLI
Configuration Manager Task
Chassis Configuration Manager
Secure Shell Daemon Task
Telnet Task
tCS_CCM2
Sshd
Telnetd
Rmon
RMON Task
tCS_CVM
SmNiMgr
TIpxTimer
TIpxGapper
SesMon_3
tTelnetOut0
tTelnetIn0
CliShell0
TPolMonSvr
TDcacheUpd
Chassis Version Manager Task
CMM-NI Shared Memory Manager
IPX Timer
IPX Routing Protocol InterPacket Gap Control
Session Monitor for Session Number
Telnet Session 0 out task
Telnet Session 0 in Task
CLI session 0 shell Task
Policy Manager Monitor LDAP Servers
FPGA Support
OmniSwitch 6624/6648 Dshell Task Definitions
tExcTask
tLogTask
tShell
Exception Handling Task
Log Task
Shell Task
tNetTask
qdrCpu
qdsCpu
Routing Task
Queue Driver of from CPU queues
Queue Dispatcher of to CPU queues
OmniSwitch Troubleshooting Guide September 2005
page 1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting the Switch System
tIpedrMsg
tahw_sch
qdsUnr
IP Ethernet Driver Task Message handler
Spanning Tree Support
Queue Dispatcher of unresolved queues
NI Stack Manager
taSM_DVR
ipcReceive
taSM_NI
la_ni_tick_
tahw_stp
IPC Receive Task
NI Stack Manager
NI Link Aggregation Timer
Spanning Tree Support
IPC Timer
IPCHAWKTIME
ipc_monitor
tNiSup&Prb
tL2Stat
IPC monitor task
NI supervision and Prober task
L2 statistics gathering task
Extended IPC task
taEipc
CfgMgr
Configuration Manager Task
MIP gateway
Gateway
EIpc
Extended IPC task
Ftpd
FTP Daemon Task
taStp
Spanning Tree task
tMemMon
tssApp_SNMP
tssApp_12_4
tCS_CCM
tCS_PRB
tCS_CMS
tCS_HSM
tCsCSMtask
SwLogging
DSTwatcher
tWhirlpool
ipc_tests
Memory Monitor task
Temporary task to support SNMP
Temporary task to support CLI
Chassis Configuration Manager
Chassis supervision Prober task
Chassis MAC Server
Chassis Supervision Hardware Services Manager
Chassis Supervision Chassis State Manager
Switch Logging task
Daylight saving task
Encryption Support
IPC debugging and test support
IPC ping task
ipc_ping
IXE2424_
IXE2424 task
page 1-18
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Dshell Troubleshooting
taNiEsmDrv
tsLnkState
PortMgr
PsMgr
NI Ethernet switching driver task
Link State monitor task
Port manager task
Power supply Manager task
VLAN Manager task
Trap manager task
VlanMgr
TrapMgr
SM_CMM
PartMgr
SNMPagt
SNMP GTW
SNMP TIMER
SesMgr
CMM Stack Manager
Partition Manager task
SNMP agent
SNMP Gateway
SNMP Agent Timer
Session Manager Task
Session Application Task
NTP Daemon Task
SsApp
Ntpd
Health
Health Monitor task
EsmDrv
SrcLrn
Ethernet NI software (ESM) driver task
Source learning task
tSlcMsgHdl
GrpMob
Stp
Source learning message handler task
Group Mobility task
Spanning tree task
stpTick
CMM Spanning tree timer
802.1Q task
8021q
LnkAgg
la_cmm_tick
AmapMgr
GmapMgr
GmapTimer
PMirMon
Ipedr
Link Aggregation task
CMM Link Aggregation timer
AMAP manager task
GMAP manager task
GMAP timer task
Port Mirroring task
IP Ethernet driver task
IP ethernet packet handler task
AAA task
tIpedrPkt
AAA
AVLAN
Authenticated VLAN task
OmniSwitch Troubleshooting Guide September 2005
page 1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting the Switch System
onex
802.1X
Vrrp
VRRP task
UdpRly
UDP Relay task
Qos
CMM QOS
PolMgr
Policy Manager task
IP Multicast Task
IP Multicast Forwarding
IP Multicast Management
Dynamic Routing Control Timer task
Ipmem
ipmfm
ipmpm
DrcTm
TDrcIprm
taDot1q_
taSLNEvent
taGmnCtrl
taVmnCtrl
taLnkAgg
taQoS
Dynamic Routing Control IP Route Manager task
802.1Q task
Source learning event handler
NI group mobility
NI VLAN manager
NI link aggregation
NI QOS task
taIpni
IP task on a NI
taIpms
IPMS task
taXMAP_ni
taUdpRelay
taAvlan
XMAP task on a NI
NI UDP relay
NI Authenticated VLAN
NI Port Mirroring
taPortMir
taQFab
Software fabric for stacks
NI source learning task
Radius task
tSLNAdrLrn
RADIUS
cliConsole
tWebTimer
tCS_CCM2
Sshd
Console
Web Session Timer
Chassis Configuration Manager
SSH daemon (secure shell)
NTP daemon (network time protocol)
RMON task
NtpDaemon
Rmon
WebView
WebView Task
page 1-20
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Dshell Troubleshooting
tCS_CVM
Chassis Version Manager
Session Monitor
SesMon_12
tTelnetOut0e4208c
tTelnetIn0
Telnet Outgoing
Telnet Incoming
CliShell0
CLI session 0 shell Task
Policy Manager Monitor LDAP Servers
FPGA Support
tPolMonSvr
tDcacheUpd
To further qualify the source of the problem we need to look at each and every NI.
Troubleshooting NIs on OmniSwitch 7700/7800/8800
Looking at the health statistics of each NI would give an idea about which one is causing the problem.
Following CLI command can be used to diagnose:
Show health <slot number>
Example:
-> show health 5
* - current value exceeds threshold
Slot 05
Resources
1 Min 1 Hr 1 Hr
Limit Curr Avg Avg Max
----------------+-------+-----+------+-----+-----+-------
Receive
Transmit/Receive
Memory
80 01
80 01
80 39
80 21
01
01
39
22
01
01
39
21
01
01
39
24
Cpu
The NI Debugger software can be launched in Dshell using the following command:
Working: [dshell]-> <nidebug
This will launch the NI Debugger. To change to a specific slot and slice (Coronado) the following
command can be used:
changeSlot slot,slice
Now the processor on that slot can be accessed just like CMM to see all tasks (running or suspended),
tasks consuming the CPU the most, and other commands like task trace (tt) or task info (ti).
Working: [Kernel]->NiDebug
1:0 nidbg>
1:0 nidbg> nisup_cpuShow
1:0
1:0 Task
1:0 Id
Cpu
Abs Rel
Name
1:0 -------- ----------- ---- ----
1:0 017fd170 tsHw_qdisp 13% 13%
1:0 015ea1c0 taIpni
1:0 015fae50 taVmnCtrl
2% 9%
0% 2%
OmniSwitch Troubleshooting Guide September 2005
page 1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting the Switch System
1:0 0160cef8 t_ipc_cmm_p 1% 1%
1:0 015f61d0 taL3Hre
0% 1%
0% 1%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
1:0 015ee670 taXMAP_ni
1:0 015f7768 taStp
1:0 015f4080 taQoS
1:0 015ed4c0 taIpms
1:0 017fb470 tExcTask
1:0 017f8fb8 tDBG_sp_tk
1:0 017f6290 tNiSup&Prb
1:0 01602bf8 taHw_qdrv
1:0 01601e30 taIpc_ni
1:0 01601450 taEipc
1:0 015fed08 taSLNEvent
1:0 015fbc18 taGmnCtrl
1:0 015fa088 taLnkAgg
1:0 015f0f90 taDot1q_ni
1:0 015eb370 taIpx
1:0 015e70d0 taUdpRelay
1:0 015e47b0 taAvlan
1:0 015e2e30 taPortMir
1:0 015e1030 tQDriverSub 0% 0%
1:0 015c09e0 la_ni_tick_ 0% 0%
1:0 015a2b28 taEniMsgHdl 0% 0%
1:0 015a16d0 tahw_stp
1:0 015a0ca0 tahw_sch
1:0 01593e98 tSLNAdrLrn
1:0 01590da8 tSLNDAMgr
1:0 014f5e80 tsLnkState
0% 0%
0% 0%
0% 0%
0% 0%
0% 0%
1:0 014f4cd0 tsStatistic 0% 0%
1:0
1:0
1:0
KERNEL
INTERRUPT
IDLE
1% 1%
0% 0%
78% 69%
1:0 value = 0 = 0x0
To force a NI to create a dump file the following command can be used in Dshell:
Working: [Kernel]->pmdni_generate 1,0,"slo1slic0.pmd"
Syntax is pmdni_generate slot,slice, file_name.
This will result in generating a PMD file for slot 1 slice 0 in /flash directory, which can then be forwarded
to Engineering for analysis. In addition, there is a software available known as “ni_pmdexploit” which can
be used on UNIX OS to exploit the PMD files in VI format. The OMD files generated on the switch for NI
are in binary format and cannot be viewed by switch log commands on the switch. These files need to be
converted to VI format to be analyzed.
The format to exploit a NI pmd file is “ni_pmdexploit <filename> < <new filename”. Once it is exploited,
it can be viewed using normal UNIX editors.
page 1-22
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Dshell Troubleshooting
OmniSwitch 6624/6648 Dshell Troubleshooting
One of the important things in OS-6600 is to confirm the stack topology. This can be confirmed using the
command:
Working: [Kernel]->smctx
****************************************************
local_slot=1 * base_mac= 00:d0:95:84:4b:d2 * local_mac=0000 1111 1111 * TYPE_48
* heart_beat=19007
state=SUPERV role=PRIMARY (primary_slot=1 secondary_slot=2) opposite_way=0
nb=7 elements=0x300ff in_loop=1 supervision=ON (check=0x10100 change=0x0)
gport1=0x1a lport1=0x1a status=1 * gport2=0x1b lport2=0x1b status=1
neighbor1 (nb1=7) [0]=0|0 [1]=8|1a [2]=7|1b [3]=6|1a [4]=5|1b [5]=4|1a [6]=3|1b
[7]=2|1a
neighbor2 (nb2=7) [0]=2|1b [1]=2|1b [2]=3|1a [3]=4|1b [4]=5|1a [5]=6|1b [6]=7|1a
[7]=8|1b
topology role
[1]=1 [2]=2 [3]=3 [4]=3 [5]=3 [6]=3 [7]=3 [8]=3
topology outport [1]=ff [2]=1b [3]=1b [4]=1b [5]=1a [6]=1a [7]=1a [8]=1a
topology base mac
[2]= 00:d0:95:84:3d:24
[3]= 00:d0:95:86:50:f2
[4]= 00:d0:95:84:49:bc
[5]= 00:d0:95:84:39:bc
[6]= 00:d0:95:84:4a:8e
[7]= 00:d0:95:84:39:f2
[8]= 00:d0:95:84:3c:42
netid [1]=1|1 [2]=0|0 [3]=0|0 [4]=0|0 [5]=0|0 [6]=0|0 [7]=0|0 [8]=0|0
lookup [1]=ff [2]=1b [3]=1b [4]=1b [5]=1b [6]=1b [7]=1b [8]=1a
subrole [1]=2 [2]=4 [3]=7 [4]=7 [5]=7 [6]=7 [7]=6 [8]=5
list
[1]=1 [2]=2 [3]=3 [4]=4 [5]=5 [6]=6 [7]=7 [8]=8 [0]=8
hop
[0] [1] [2] [3] [4] [5] [6] [7] [8]
[0] -1 -1 -1 -1 -1 -1 -1 -1 -1
[1] -1 0 1 2 3 4 5 6 1
[2] -1 1 0 1 2 3 4 5 6
[3] -1 2 1 0 1 2 3 4 5
[4] -1 3 2 1 0 1 2 3 4
[5] -1 4 3 2 1 0 1 2 3
[6] -1 5 4 3 2 1 0 1 2
[7] -1 6 5 4 3 2 1 0 1
[8] -1 1 6 5 4 3 2 1 0
*****************************************************************
value = 2 = 0x2
This command indicates the role of the local stack.
output definitions
Local slot
Base Mac
Local Stack ID.
Base Mac Address of this Stack.
OmniSwitch Troubleshooting Guide September 2005
page 1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting the Switch System
output definitions (continued)
Local Mac
Local Mac address used for IPC communication across the stacking
cables.
Role
Primary or Secondary.
Nb
Neighbor ID (1-Based).
In_loop
1 if the stacks are connected in a loop for redundant path.
Shows the connections to other stacks through the port number.
1=Primary, 2= Secondary, 3=Idle.
Neighbor1
Topology Role
Topology Outport
Topology base Mac
Lookup
Displays the port used to access the other stacks.
Displays the base mac addresses of all the other stacks.
The stacking port to be used to do a lookup for another stack.
Displays the hops for each stack to the other stack.
Hop
Gport
Global port used for stacking (either stack_number a or stack_number
b).
Lport
Status
Logical port used for stacking (either stack_number a or stack_number
b).
1=up, 0=down.
To view the stack topology in detail, use the following command:
Working: [Kernel]->stack_topo
local_slot=1 role=PRIMARY P=1 S=2 (elements=0x300ff nb=8 loop=1 sup=2 type=2)
7 elements seen by link1 (gport=0x1a lport=0x1a status=1)
slot=8 originate_port=26 role=IDLE
slot=7 originate_port=27 role=IDLE
slot=6 originate_port=26 role=IDLE
slot=5 originate_port=27 role=IDLE
slot=4 originate_port=26 role=IDLE
slot=3 originate_port=27 role=IDLE
slot=2 originate_port=26 role=SECONDARY
7 elements seen by link2 (gport=0x1b lport=0x1b status=1)
slot=2 originate_port=27 role=SECONDARY
slot=3 originate_port=26 role=IDLE
slot=4 originate_port=27 role=IDLE
slot=5 originate_port=26 role=IDLE
slot=6 originate_port=27 role=IDLE
slot=7 originate_port=26 role=IDLE
slot=8 originate_port=27 role=IDLE
NI=1 CMM=65 role=1
* state_linkA=1 remote_slotA=8 remote_linkA=51
* state_linkB=1 remote_slotB=2 remote_linkB=52
NI=2 CMM=66 role=2
* state_linkA=1 remote_slotA=3 remote_linkA=27
* state_linkB=1 remote_slotB=1 remote_linkB=52
NI=3 CMM=0 role=3
* state_linkA=1 remote_slotA=2 remote_linkA=51
* state_linkB=1 remote_slotB=4 remote_linkB=52
page 1-24
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Dshell Troubleshooting
NI=4 CMM=0 role=3
* state_linkA=1 remote_slotA=5 remote_linkA=51
* state_linkB=1 remote_slotB=3 remote_linkB=28
NI=5 CMM=0 role=3
* state_linkA=1 remote_slotA=4 remote_linkA=51
* state_linkB=1 remote_slotB=6 remote_linkB=52
NI=6 CMM=0 role=3
* state_linkA=1 remote_slotA=7 remote_linkA=51
* state_linkB=1 remote_slotB=5 remote_linkB=52
NI=7 CMM=0 role=3
* state_linkA=1 remote_slotA=6 remote_linkA=51
* state_linkB=1 remote_slotB=8 remote_linkB=52
NI=8 CMM=0 role=3
* state_linkA=1 remote_slotA=1 remote_linkA=51
* state_linkB=1 remote_slotB=7 remote_linkB=52
output definitions
local slot number
Local stack number.
role
Either Primary, secondary or idle.
Number of stacks.
nb
loop
If redundant path is available
elements seen by link
Number of elements seen by the link with the global/local port number
as 1a, in the order they are seen and the role of each stack
NI
NI number of the switch in the stack.
CMM
CMM number of the switch in the stack. CMM number can be 65 (Pri-
mary), 66 (Secondary) or 0 (Idle). Role can be 1 (Primary), 2 (Second-
ary) or 3 (Idle).
state_link
Status of link A and B which can be 1 if up or 0 if down.
Remote slot number.
remote_slot
remote_link
Remote link number.
Accessing Dshell on Idle Switches
OS6600 in standalone environment is like one NI for OmniSwitch 7000 and 8000 series switches. Just
going into Dshell will allow the use of normal Vx Works commands.
There are two ways to access Dshell. One is using the dshell command from CLI or pressing control-w,
control-w (twice). The second method is used when the console or telnet is not accessible. However,
before doing so, it must be enabled by following the steps below on the primary and secondary switches:
1 From the CLI prompt enter:
->dshell
2 From the Dshell prompt enter
Certified: [Kernel]->WWON=1
OmniSwitch Troubleshooting Guide September 2005
page 1-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using AlcatelDebug.cfg
Troubleshooting the Switch System
In stacking environment, only the primary and secondary switches have console enabled whereas console
is disabled for the idle switches. To enable the Dshell access to the idle switches use the following
command on primary stack:
Nisup_control_WW_on slot
You must execute this command on each idle switch in the stack. Please note that these switches will not
allow to exit with the exit command. To restore normal Dshell access you will need to reboot the switch.
Using AlcatelDebug.cfg
When you are using IPMS/DVMRP with 802.1Q it is recommended that debug interfaces set backpres-
sure enable be used. This command can be put in the boot.cfg file, but it is overwritten as soon as write
memory is issued, since it is a debug command and the setting is lost after a reboot. To retain the debug
settings after a system reboot, put debug commands into a file called AlcatelDebug.cfg in both the work-
ing and certified directories. Use Notepad or VI editor to create the AlcatelDebug.cfg file.
Example:
-> vi AlcatelDebug.cfg
-> debug set WWON 1 => to allow dshell access in the event of the console lockup
-> debug set esmDebugLevel 4 => see port up/down event on swlog
-> debug interfaces set backpressure enable => to enable system backpressure
page 1-26
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Troubleshooting IPC on OS-6/7/8XXX Series of Switches
Troubleshooting IPC on OS-6/7/8XXX Series of
Switches
IPC (Inter Process Communication) is should by the system to communicate between different software
modules. This communication can be between different processes in the same software module or between
two entirely separate modules. This process can be between NI and CMM or between CMM to CMM.
Burst Bus commonly known as BBUS (management bus) is used for the IPC communication. IPC uses
connectionless build-in Vx Works sockets to communicate.
Typical problems that can arise because of the problems with IPC can cause the following symptoms:
• Loss of access to the console of the switch
• Loss of messages between CMM and NI resulting in switching and routing problems.
• High CPU utilization on CMM
Debugging IPC
IPC has 5 different buffer pools:
• Urgent Pools
• Control Pools for control messages
• Normal Pools for some control messages as well as other messages
• Jumbo Pools
• Local Pools
Each of these pools have some dedicated buffers available. Once any of these processes initiates a socket
to communicate, it is suppose to tear the socket down after the communication is done. If it does not tear
the socket then it might result in occupying the buffer space which will not be available for other
processes.
IPC pools can be looked in dshell using the command:
Working: [Kernel]->ipc_pools
UrgentPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
ControlPool: Full size is 5096, remaining: 5090
In socket queues: 1 Not queued: 3:
In DMA queues: 2
NormalPool: Full size is 2024, remaining: 2022
In socket queues: 0 Not queued: 2:
In DMA queues: 0
JumboPool: Full size is 256, remaining: 255
In socket queues: 1 Not queued: 0:
In DMA queues: 0
OmniSwitch Troubleshooting Guide September 2005
page 1-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IPC on OS-6/7/8XXX Series of Switches
Troubleshooting the Switch System
LocalPool: Full size is 64, remaining: 64
In socket queues: 0 Not queued: 0:
In DMA queues: 0
Each type of pool has the following listed in the command output:
• Maximum size of buffers available
• Currently available buffers
• Socket Queues being used
• Not Queued in pool
• Direct Memory Access Queues
Currently available buffers should always be around the maximum available in normal operation. In some
scenarios, it might happen that the remaining pools are decrementing at a fast rate and are never freeing up
the buffers. This can lead to problem with IPC.
Iterative use of the command will help to identify the situation.
An example is as follows:
Working: [Kernel]->ipc_pools
UrgentPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
ControlPool: Full size is 5096, remaining: 5062
In socket queues: 4 Not queued: 20:
In DMA queues: 10
NormalPool: Full size is 2024, remaining: 2022
In socket queues: 0 Not queued: 2:
In DMA queues: 0
JumboPool: Full size is 256, remaining: 255
In socket queues: 1 Not queued: 0:
In DMA queues: 0
LocalPool: Full size is 64, remaining: 64
In socket queues: 0 Not queued: 0:
In DMA queues: 0
Working: [Kernel]->ipc_pools
UrgentPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
ControlPool: Full size is 5096, remaining: 5060
In socket queues: 6 Not queued: 20:
In DMA queues: 10
NormalPool: Full size is 2024, remaining: 2022
In socket queues: 0 Not queued: 2:
In DMA queues: 0
JumboPool: Full size is 256, remaining: 255
In socket queues: 1 Not queued: 0:
In DMA queues: 0
page 1-28
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Troubleshooting IPC on OS-6/7/8XXX Series of Switches
LocalPool: Full size is 64, remaining: 64
In socket queues: 0 Not queued: 0:
DMA queues: 0
In the above two outputs it seems that the control pool is stuck and the socket queues are incrementing. In
order to find out which task is using these queues we need to look at the socket information.
To look in detail about these pools the following commands can be used in Dshell:
• Ipc_urgent_pools_detail number
• Ipc_control_pools_detail number
• Ipc_normal_pools_detail number
• Ipc_jumbo_pools_detail number
• Ipc_local_pools_detail number
The above commands have an option to specify the number of sockets to be displayed in Dshell. If no
number is specified then it will display all the sockets in use which can be real problem in case of thou-
sands of sockets being used.
Working: [Kernel]->ipc_control_pools_detail
ipc_control_pools_details
ControlPool: Full size is 5096, remaining: 5090
Socket ID = 0x3, dest slot = 66, remote addr = 0x0, ipc status = D
Task ID = 0x67f3c10, PayLoad Len= 68, ipc priority = 0x1, data ptr = 0x5e09f9
8
next = 0x0, pFreeQ = 0x6f565d0, data_offset = 0, free_list_num = 3
Socket ID = 0x5, dest slot = 66, remote addr = 0x8400041, ipc status = D
Task ID = 0x67f3c10, PayLoad Len= 68, ipc priority = 0x1, data ptr = 0x5e09ff
8
next = 0x0, pFreeQ = 0x6f565d0, data_offset = 0, free_list_num = 3
Socket ID = 0x8, dest slot = 66, remote addr = 0xf400042, ipc status = G
Task ID = 0x6862660, PayLoad Len= 64, ipc priority = 0x1, data ptr = 0x5e0a1d
8
next = 0x6818ba4, pFreeQ = 0x6f565d0, data_offset = 0, free_list_num = 3
Socket ID = 0x8, dest slot = 66, remote addr = 0xf400042, ipc status = G
Task ID = 0x6862660, PayLoad Len= 64, ipc priority = 0x1, data ptr = 0x5e1ba5
8
next = 0x68231d8, pFreeQ = 0x6f565d0, data_offset = 0, free_list_num = 3
Socket ID = 0x8, dest slot = 65, remote addr = 0x5090041, ipc status = S
Task ID = 0x6862660, PayLoad Len= 68, ipc priority = 0x1, data ptr = 0x5e202b
8
next = 0x0, pFreeQ = 0x6f565d0, data_offset = 0, free_list_num = 3
Socket ID = 0x1, dest slot = 66, remote addr = 0x10400042, ipc status = G
Task ID = 0x6862660, PayLoad Len= 64, ipc priority = 0x1, data ptr = 0x5e6999
8
next = 0x0, pFreeQ = 0x6f565d0, data_offset = 0, free_list_num = 3
In socket queues: 1 Not queued: 3:
In DMA queues: 2
OmniSwitch Troubleshooting Guide September 2005
page 1-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IPC on OS-6/7/8XXX Series of Switches
Troubleshooting the Switch System
value = 10 = 0xa
Working: [Kernel]->
The above command displays a lot of information but we are interested in the most repeating socket ID. In
the above example it is 0x8. To look into what does this socket means the following command can be used
in Dshell:
Working: [Kernel]->ipc_socket_info 0x8
ipc_socket_info
Socket 8:
LocalSocketID = 0x8, localidx = 0x8, Local_address = 0xf400041
RemoteSocketID = 0x8, Remote_Address = 0xf400042
QnumBufs = 1, NumBufs = 1588, seqSent = 1588, seqRecv = 1588
USRnumBufs = 1, State = 0x3, OptionFlgs = 0x0, priority = 1
blk_timeout = 0, LingerTime = 0, RxQ_Full_Threshold = 65536,
RxQ_Numbuf_Threshold = 128 congestion = 0, SockMask = 0x100,
SockMsbs = 0x0, use_sw_buf = 1
remote_cong = 0, init_done = 13, sem_use = 0, alignmentSpace = 0
Task id = 0x67f3c10 (tCsCSMtask), LastTimeStamp = 1046954691
recvErrs = 0, txCnt = 1588, txErr = 0, eagainCnt = 0
xoffsent = 0, xonsent = 0, xoffrecv = 0, xonrecv = 0, congcount = 0
value = 8 = 0x8
Working: [Kernel]->
The output of the above command shows that tCsCSMtask is the one consuming this socket.
Older versions of the code might not show the task name in the task ID so the following command can be
used to find out the tasked:
Working: [Kernel]->ti 0x67f3c10
NAME
---------- ------------ -------- --- ---------- -------- -------- ------- -----
tCsCSMtask csCsmMain 67f3c10 94 PEND 158540 67f34a0 3d0002
ENTRY
TID
PRI STATUS
PC
SP
ERRNO DELAY
0
stack: base 0x67f3c10 end 0x67eede8 size 19320 high 15072 margin 4248
options: 0x4
VX_DEALLOC_STACK
%pc = 158540 %npc = 158544 %ccr =
44 %y
0 %tl =
=
0
0
%asi =
%pil =
%g0 =
%g3 =
%g6 =
15 %cwp =
0 %pstate =
0 %tt =
1e
0 %g1 =
0 %g4 =
0 %g7 =
0 %g2 =
0 %g5 =
0 %i0 =
0
0
67eedc0
%i1 = ffffffffffffffff %i2 =
1e5c54 %i3 =
264c00 %fp =
0 %l1 =
0
%i4 =
%i7 =
%l2 =
%l5 =
%o0 =
%o3 =
%sp =
158440 %i5 =
158b4c %l0 =
0 %l3 =
6a62038 %l6 =
0 %o1 =
67f3560
67eedc0
66fc800
14 %l4 =
66ff810 %l7 =
0 %o2 =
0 %o5 =
0
4
0
0
0 %o4 =
67f34a0 %o7 =
value = 109001744 = 0x67f3c10
Working: [Kernel]->
page 1-30
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Troubleshooting IPC on OS-6/7/8XXX Series of Switches
Now doing a task trace on this task can be helpful to see if the task is moving:
Working: [Kernel]->tt 0x67f3c10
108e9c vxTaskEntry
00, 6a69800)
+c : Letext (&dataInfo, 67f3920, 67f3a20, 34000000, 66ff8
66b69b4 Letext
6ff56f8 zcSelect
158b4c semTake
ke, 264c00)
+2d4: zcSelect (5, 67f3a20, 0, 0, 6a6c800, 247)
+458: semTake (67eedc0, ffffffff, a, 28, a, 0)
+2c : semBTake (67eedc0, ffffffff, &semTakeTbl, 0, &semBTa
value = 0 = 0x0
Working: [Kernel]->
Using this command multiple times will give an idea if the task is stuck in some routine.
Gathering this data and attaching in the Problem Report will help Engineering to identify the source of the
problem.
The CMM also keeps a prospective of NI for their IPC Pools. These can be displayed using the following
commands:
• IpcSlotPools slot,slice
• IpcSlotUrgentPoolsDetail slot,slice
• IpcSlotControlPoolsDetail slot,slice
• IpcSlotNormalPoolsDetail slot,slice
• IpcSlotJumboPoolsDetail slot,slice
• IpcSlotLocalPoolsDetail slot,slice
Rest of the information about the sockets and the tasks can be found using the same commands as
discussed above.
If a NI generating many IPC messages then CMM might not be able to see the IPC pools of that and as
well as any other NI. E.g.
Certified: [Kernel]->ipcSlotPools 6,0
ipcSlotPools slot 6, slice 0
UrgentPool: Full size is 0, remaining: 256
In socket queues: 0 Not queued: 0:
In DMA queues: 0
ControlPool: Full size is 0, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
NormalPool: Full size is 0, remaining: 255
In socket queues: 0 Not queued: 0:
In DMA queues: 0
JumboPool: Full size is 0, remaining: 64
In socket queues: 0 Not queued: 0:
In DMA queues: 0
OmniSwitch Troubleshooting Guide September 2005
page 1-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IPC on OS-6/7/8XXX Series of Switches
Troubleshooting the Switch System
LocalPool: Full size is 0, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
value = 6 = 0x6
The above display of the command does not show the Full size of any of the pools. This indicates that
CMM is unable to view the IPC pools of the NI. In this scenario, one needs to load the NI Debugger and
go to the NI and look at the IPC Pools. One of the NI would be generating many IPC messages that would
result in IPC sockets to be eaten up by that NI resulting in flooding of enormous amount of IPC messages
and in turn loosing communication with the CMM.
The following is an example of using the NiDebug command to display the IPC pools of all NIs.
Certified:[Kernel]->NiDebug
nidbg> ipc_pools
ipc_pools
UrgentPool: Full size is 256, remaining: 256
In socket queues: 0 Not queued: 0:
In DMA queues: 0
ControlPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
NormalPool: Full size is 256, remaining: 131
In socket queues: 123 Not queued: 2:
In DMA queues: 0
JumboPool: Full size is 64, remaining: 64
In socket queues: 0 Not queued: 0:
In DMA queues: 0
LocalPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
value = 0 = 0x0
nidbg> ipc_normal_pools_detail 10
ipc_normal_pools_details
NormalPool: Full size is 256, remaining: 135
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
62d108
next = 0x17ca60c, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
630108
next = 0x17c8bec, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
page 1-32
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Troubleshooting IPC on OS-6/7/8XXX Series of Switches
631908
next = 0x17c8c44, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
632108
next = 0x17caab0, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
632908
next = 0x17c98d0, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
633908
next = 0x17c9d1c, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
634108
next = 0x17c9e7c, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
634908
next = 0x17ca244, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
635908
next = 0x17ca1ec, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
Socket ID = 0x19, dest slot = 2, remote addr = 0x3030002, ipc status = S
Task ID = 0x17fd170, PayLoad Len= 128, ipc priority = 0x1, data ptr = 0x1
636908
next = 0x0, pFreeQ = 0x2fc7a8, data_offset = 0, free_list_num = 6
In socket queues: 119 Not queued: 2:
In DMA queues: 0
value = 10 = 0xa
LocalSocketID = 0x19, localidx = 0x19, Local_address = 0x100b0002
RemoteSocketID = 0x0, Remote_Address = 0x0
QnumBufs = 124, NumBufs = 4276, seqSent = 0, seqRecv = 0
USRnumBufs = 0, State = 0x2, OptionFlgs = 0x0, priority = 1
blk_timeout = 0, LingerTime = 0, RxQ_Full_Threshold = 65536, RxQ_Numbuf_Thre
shold = 128
congestion = 0, SockMask = 0x2000000, SockMsbs = 0x0, use_sw_buf = 0
remote_cong = 0, init_done = 0, sem_use = 0, alignmentSpace = 0
Task id = 0x15f7768 (taStp), LastTimeStamp = 0
recvErrs = 0, txCnt = 68, txErr = 0, eagainCnt = 0
xoffsent = 0, xonsent = 0, xoffrecv = 0, xonrecv = 0, congcount = 0
value = 25 = 0x19
OmniSwitch Troubleshooting Guide September 2005
page 1-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IPC on OS-6/7/8XXX Series of Switches
Troubleshooting the Switch System
nidbg> tt 0x15f7768
1e6ce0 vxTaskEntry
0, 0)
f22e8 stp_task_entry +80 : stpNISock_start (22bc00, 22bea0, 22bdc4, 3, 22bd
f4, 3)
+c : stp_task_entry (0, 0, 0, 0,
Multiple task trace of the task with IPC Pools should be taken. This process might have to be repeated on
multiple NI in order to find out the cause of the problem and identify the NI causing the problem to
happen.
OmniSwitch 6624/6648 Example
Follow the steps below for an example of displaying IPC pool data on an OmniSwitch 6624/6648;r
1 Check the In socket queues and Not queued fields for all the pools and identify the pool that has the
highest value with the ipc_pools command as shown below:
Working: [Kernel]->ipc_pools
ipc_pools
UrgentPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
ControlPool: Full size is 4096, remaining: 3451
In socket queues: 640 Not queued: 5:
In DMA queues: 0
NormalPool: Full size is 1024, remaining: 377
In socket queues: 620 Not queued: 16:
In DMA queues: 0
JumboPool: Full size is 256, remaining: 256
In socket queues: 0 Not queued: 0:
In DMA queues: 0
LocalPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
value = 1 = 0x1
2 Find the most repeated socket ID ipc_normal_pools_detail command as shown below:
Working: [Kernel]->ipc_pools_detail 1,0
NormalPool: Full size is 1024, remaining: 377
Socket ID = 0x7, dest slot = 1, remote addr = 0x60001, ipc status = G
Task ID = 0x756ba38, PayLoad Len= 20, ipc priority = 0x1, data ptr = 0x6cfcba
0
next = 0x0, pFreeQ = 0x74fb4e0, data_offset = 0, free_list_num = 6
Socket ID = 0x100, dest slot = 90, remote addr = 0x50001, ipc status = S
Task ID = 0x7571700, PayLoad Len= 812, ipc priority = 0x1, data ptr = 0x6cfd3
a0
next = 0x739fac0, pFreeQ = 0x74fb4e0, data_offset = 0, free_list_num = 6
page 1-34
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Troubleshooting IPC on OS-6/7/8XXX Series of Switches
Socket ID = 0x100, dest slot = 5, remote addr = 0x5400042, ipc status = S
Task ID = 0x7571700, PayLoad Len= 812, ipc priority = 0x1, data ptr = 0x6cfe3
a0
a0
0
next = 0x739b810, pFreeQ = 0x74fb4e0, data_offset = 0, free_list_num = 6
Socket ID = 0x100, dest slot = 65, remote addr = 0x8440041, ipc status = S
Task ID = 0x7571700, PayLoad Len= 812, ipc priority = 0x1, data ptr = 0x6cfeb
next = 0x7396da4, pFreeQ = 0x74fb4e0, data_offset = 0, free_list_num = 6
Socket ID = 0x2, dest slot = 65, remote addr = 0x11b0001, ipc status = G
Task ID = 0x5514c80, PayLoad Len= 20, ipc priority = 0x1, data ptr = 0x6cffba
next = 0x73a1cac, pFreeQ = 0x74fb4e0, data_offset = 0, free_list_num = 6
3 Obtain the task ID with the ipc_socket_info command. Use the most-repeated socket ID discovered in
Step 2.
Certified: [Kernel]->ipc_socket_info 0x100
ipc_socket_info
Socket 100:
LocalSocketID = 0x100, localidx = 0x100, Local_address = 0x5450041
RemoteSocketID = 0x0, Remote_Address = 0x0
QnumBufs = 128, NumBufs = 193, seqSent = 0, seqRecv = 0
USRnumBufs = -65, State = 0x2, OptionFlgs = 0x0, priority = 1
blk_timeout = 0, LingerTime = 0, RxQ_Full_Threshold = 65536,
RxQ_Numbuf_Threshold = 128
congestion = 0, SockMask = 0x200, SockMsbs = 0x5, use_sw_buf = 0
remote_cong = 0, init_done = 0, sem_use = 0, alignmentSpace = 0
Task id = 0x4e105c0 (WebView), LastTimeStamp = 1063601688
recvErrs = 0, txCnt = 0, txErr = 0, eagainCnt = 0
xoffsent = 0, xonsent = 0, xoffrecv = 0, xonrecv = 0, congcount = 0
value = 68 = 0x44 = 'D'
4 Dump the task ID discovered in Step 3 with the tt command as shown below:
Certified: [Kernel]->tt 0x4e105c0
Run this command 3–4 times.
On the primary switch in the stack you can execute the debugDisplayRcvDesc Dshell command to see the
near-end of IPC health as shown below:
->dshell
Certified: [Kernel]-> debugDisplayRcvDesc
OmniSwitch Troubleshooting Guide September 2005
page 1-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Port Numbering Conversion Overview
Troubleshooting the Switch System
Port Numbering Conversion Overview
The sections below document how to convert port number parameters.
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
ifindex to gport
To convert from ifindex to global port (gport) number use the findGlobalPortFromIfIndex Dshell
command as shown below:
-> dshell
Working: [Kernel]->findGlobalPortFromIfIndex 16011
value = 505 = 0x1f9
gport to ifindex
To convert from global port (gport) to ifindex use the findIfIndexFromGlobalPort Dshell command as
shown below:
-> dshell
Working: [Kernel]->findIfIndexFromGlobalPort 505
value = 16011 = 0x3e8b
Converting from lport
The lport numbering process varies on each platform type (e.g., Falcon/Eagle or Hawk), as well as
module type (e.g., ENI-C24, GNI-C2, GNI-U12, GNI-U8, GNI-C24, GNI-U24, etc.). To determine the
lport value use two Dshell commands: dmpValidPorts and dmpAbsPort.
The following subsections describe conversions based on platform type. You need to be careful that both
commands can be used on either Dshell or Nidebug based on platform type. In addition, input values for
dmpAbsPort vary depending on platform type.
OmniSwitch 7700/7800/8800 (Falcon/Eagle) Example
The following displays all valid lport values with the dmpValidPorts command from NiDebug. After-
wards, you should do a dump for each slice.
1 Use the dmpValidPorts command as shown below:
8:0 nidbg> dmpValidPorts
8:0
8:0
valid lports: [ 0 ][ 1 ][ 2 ][ 3 ][ 4 ][ 5 ]
8:0 valid uports: [ 1 ][ 2 ][ 3 ][ 4 ][ 5 ][ 6 ]
2 Find the corresponding lport value from the uport value using dmpAbsPort command. Please note
that you must use the uport value for this command.
8:0 nidbg> dmpAbsPort 1
page 1-36
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the Switch System
Port Numbering Conversion Overview
Note that 1 is the uport number. Output similar to the following will be displayed:
8:0
8:0
8:0
Valid
in LSM
1
0
8:0 ---------- Port Numbers ------------------
8:0
8:0
8:0
8:0
8:0
8:0
8:0
8:0
8:0
8:0
Slot
Slice
Mac
Bus
phy
gport
lport
iport
pport
uport
8
0
0
0
0
224
0
0
0
1
OmniSwitch 6624/6648 (Hawk) Example
Find all valid lports values with the dmpValidPorts command from Dshell on each element (i.e., each
slot in a stack). Afterwards, you should do a dump for each slot.
1 Use the dmpValidPorts command as shown below:
Certified: [Kernel]->dmpValidPorts
valid lports: [ 0 ][ 1 ][ 2 ][ 3 ][ 4 ][ 5 ][ 6 ][ 7 ][ 8 ][ 9 ][ 10 ][ 11 ][ 12
][ 13 ][ 14 ][ 15 ][ 16 ][ 17 ][ 18 ][ 19 ][ 20 ][ 21 ][ 22 ][ 23 ][ 24 ][ 25 ][
26 ][ 27
][ 32 ][ 33 ][ 34 ][ 35 ][ 36 ][ 37 ][ 38 ][ 39 ][ 40 ][ 41 ][ 42 ][ 43 ][ 44 ][
45 ][ 46 ][ 47 ][ 48 ][ 49 ][ 50 ][ 51 ][ 52 ][ 53 ][ 54 ][ 55 ][ 58 ][ 59 ]
value = 1 = 0x1
2 Find the corresponding uport value from lport value using the dmpAbsPort command. Make sure you
use the lport value as the input value. This is different from Falcon/Eagle.
Certified: [Kernel]->dmpAbsPort 49
Note that 49 is the lport number. Output similar to the following will be displayed:
Valid
in LSM
portType
1
0
4
---------- Port Numbers ------------------
Slot
3
177
49
17
17
gport
lport
dport
pport
uport
42
OmniSwitch Troubleshooting Guide September 2005
page 1-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Port Numbering Conversion Overview
Troubleshooting the Switch System
page 1-38
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Switched
Ethernet Connectivity
This chapter assumes that it has been verified that the connectivity problem is across Ethernet media and
the connection between the non-communicating devices is switched/bridged not routed (i.e., Devices are
in the same IP Subnet).
For configuration assistance in designing and configuring switched Ethernet connectivity, please refer to
the “Configuring Ethernet Ports” chapter in the appropriate OmniSwitch Network Configuration Guide.
For known specifications and limitations, Please refer to the appropriate Release Notes Revision.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of Troubleshooting Approach
Troubleshooting Switched Ethernet Connectivity
Overview of Troubleshooting Approach
• Verify physical layer connectivity.
• Verify current running configuration is accurate.
• Verify source learning.
• Investigate any error conditions.
• Verify health of NIs involved.
• Verify health of CMM.
Client A
Client B
OmniSwitch 7800
5/1
5/2
IP = 192.168.10.2
IP = 192.168.103
VLAN 7
Diagram 1
page 2-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Switched Ethernet Connectivity
Verify Physical Layer Connectivity
Verify Physical Layer Connectivity
Verify that there is valid link light along the entire data path between the devices that can not switch to
each other. Make sure to include all interswitch links. Verify LED’s on all involved CMMs and NIs are
Solid OK1, Blinking OK2. If this is not the case, contact technical support.
Use the show interfaces command to verify operational status is Up, speed and duplex are correct and
match the other side of the connection. Run this command on the same interface multiple times to verify
errors (Error Frames, CRC Error Frames, Alignment Errors) are not incrementing. If the error counts are
incrementing verify the health of the cabling as well as the NIC involved. Also note that if the Collision
Frames is incrementing, this is normal for a half duplex connection. If the port is set to full duplex and
these errors are still incrementing, verify the duplex setting on the other side of the connection. Finally, if
these commands were run while the end stations were trying to ping each other, verify Bytes Received is
incrementing. If is not, verify the NIC card.
Note. Remember to do this for each port along the data path, not just the ports that directly attached to the
end stations.
-> show interfaces 5/1
Slot/Port 5/1 :
Operational Status
Type
MAC address
: up,
: Fast Ethernet,
: 00:d0:95:7a:63:87,
BandWidth (Megabits) : 100,
Duplex
: Full,
Long Accept
: Enable,
Runt Accept
: Disable,
Long Frame Size(Bytes) : 1553,
Input :
Runt Size(Bytes) : 64
Bytes Received
Lost Frames
Unicast Frames
:
:
:
14397,
0,
6,
Broadcast Frames :
Multicast Frames :
UnderSize Frames :
OverSize Frames :
Collision Frames :
93,
7,
0,
0,
0,
Error Frames
:
0,
CRC Error Frames :
Alignments Error :
Output :
0,
0
Bytes transmitted :
83244,
0,
10,
84,
1106,
0,
Lost Frames
Unicast Frames
:
:
Broadcast Frames :
Multicast Frames :
UnderSize Frames :
OverSize Frames :
Collision Frames :
0,
0,
Error Frames
:
0
If the port reports operational status down, verify the physical link, but also verify the necessary NIs and
CMM are receiving power and are up and operational. Use the show ni command followed by the slot
number and the show cmm command to verify this.
OmniSwitch Troubleshooting Guide September 2005
page 2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Verify Physical Layer Connectivity
Troubleshooting Switched Ethernet Connectivity
-> show ni 5
Module in slot 5
Model Name:
OS7-ENI-C24 ,
Description:
24PT 10/100 MOD,
Part Number:
902136-10,
Hardware Revision:
Serial Number:
Manufacture Date:
Firmware Version:
Admin Status:
A02,
22030298,
MAY 18 2002,
6,
POWER ON,
Operational Status:
Power Consumption:
Power Control Checksum:
MAC Address:
UP,
44,
0x808,
00:d0:95:7a:63:87,
ASIC - Physical:
0x1a01 0x0201 0x0201 0x001e 0x001e 0x001e
-> show cmm
Module in slot CMM-A-1
Model Name:
OS7800-CMM ,
Description:
BBUS Bridge,
Part Number:
901753-10,
Hardware Revision:
Serial Number:
306,
2153117A,
Manufacture Date:
Firmware Version:
Admin Status:
APR 11 2002,
38,
POWER ON,
Operational Status:
Power Consumption:
Power Control Checksum:
MAC Address:
UP,
85,
0x80e,
00:d0:95:79:62:8a,
ASIC - Physical:
Module in slot CMM-A-2
Model Name:
0x0801 0x0801 0x0801 0x0801 0x0801 0x0801 0x08
,
Description:
Part Number:
Hardware Revision:
Serial Number:
Manufacture Date:
Firmware Version:
Processor,
901753-10,
303,
2133035A,
APR 11 2002,
38
page 2-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Switched Ethernet Connectivity
Verify Current Running Configuration
Verify Current Running Configuration
If the physical layer looks OK, then verify the configuration. Use the show configuration snapshot all to
display the current running configuration. Use this command to verify the ports that are involved are in the
correct VLAN. Also review the output of the command to verify there is nothing explicit in the configura-
tion that would cause the problem, such as a deny ACL that could be found under the QoS subsection.
-> show configuration snapshot all
! Chassis :
system name OS7800
! Configuration:
! VLAN :
vlan 7 enable name "VLAN 7"
vlan 7 port default 5/1
vlan 7 port default 5/2
! 802.1Q :
! Spanning tree :
! Bridging :
! IPMS :
! AAA :
aaa authentication console "local"
! QOS :
qos apply
! Policy manager :
! Session manager :
! SNMP :
! IP route manager :
ip router router-id 127.0.0.1
ip router primary-address 127.0.0.1
! RIP :
! OSPF :
! BGP :
! IP multicast :
! Health monitor :
! Interface :
! Link Aggregate :
! Port mirroring :
! UDP Relay :
! Server load balance :
! System service :
! VRRP :
! Web :
! AMAP :
! GMAP :
! Module :
OmniSwitch Troubleshooting Guide September 2005
page 2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Verify Source Learning
Troubleshooting Switched Ethernet Connectivity
To further verify the ports are in the correct VLAN and that they are in spanning tree forwarding instead of
blocking use the show vlan port command. Also note that the port type must match what it is connecting
to. If the port is 802.1Q tagged enabled for the required vlan, then the device it attaches to must also be Q
tagged enabled for that vlan. Remember to run this command on all ports in the data path.
-> show vlan 7 port
port
type
status
--------+---------+--------------
5/1
5/2
5/9
default forwarding
default forwarding
qtagged
inactive
If ports that should be in forwarding are in blocking, or vice versa, please consult Chapter 4, “Trouble-
Verify Source Learning
If the configuration looks correct, source learning should be examined. If connectivity exists but is slow,
or intermittent source learning could be the root cause, since data packets would be flooded. However, if
there is no packet throughput between the devices the problem is likely not due to a source learning prob-
lem.
To verify that the MAC addresses are being learned correctly use the show mac-address-table slot
command. Verify that the correct mac address is being learned of the correct port, in the correct vlan.
-> show mac-address-table slot 5
Legend: Mac Address: * = address not valid
Vlan
Mac Address
Type
Protocol
Operation
Interface
------+-------------------+--------------+-----------+------------+-----------
7 00:00:39:73:13:0e
7 00:b0:d0:75:f1:97
learned
learned
10800
10800
bridging
bridging
5/1
5/2
Total number of Valid MAC addresses above = 2
page 2-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Switched Ethernet Connectivity
Verify Switch Health
Verify Switch Health
If source learning appears to be not working correctly, verify the health of the switch with the show health,
and show health slot commands. Be sure to run the latter command on all necessary NIs. Any variables
that have reached or exceeded their limit value could cause forwarding problems on the switch. In this
case please contact Technical Support. For more detailed source learning trouble shooting, please see
-> show health
* - current value exceeds threshold
Device
Resources
1 Min 1 Hr 1 Hr
Limit Curr Avg Avg Max
-----------------+-------+------+------+-----+----
Receive
Transmit/Receive
Memory
80
80
80
80
50
00
00
39
02
39
31
00
00
39
02
39
31
00
00
39
02
39
31
00
00
39
03
39
31
Cpu
Temperature Cmm
Temperature Cmm Cpu 50
-> show health 5
* - current value exceeds threshold
Slot 05
Resources
1 Min 1 Hr 1 Hr
Limit Curr Avg Avg Max
-----------------+-------+------+------+-----+----
Receive
Transmit/Receive
Memory
80
80
80
80
00
01
16
29
00
01
16
33
00
01
16
32
01
01
16
35
Cpu
Verify ARP
If everything checked appears to be valid, verify that this is not an ARP problem. On the end stations
involved, enter a static mac address for the device it is trying to communicate with. If connectivity is
restored, please see Chapter 11, “Troubleshooting ARP.”
OmniSwitch Troubleshooting Guide September 2005
page 2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Log File
Troubleshooting Switched Ethernet Connectivity
Using the Log File
If none of the above suggest a reason as to why Ethernet switching is not properly working, look into the
log file and see if there are any messages that may suggest why switching is not working properly. Use the
show log swlog command to view the system log file. Look for evidence of a system or interface problem
around the time the problem began.
-> show log swlog
Displaying file contents for ’swlog2.log’
FILEID: fileName[swlog2.log], endPtr[32]
configSize[64000], currentSize[64000], mode[2]
Displaying file contents for ’swlog1.log’
FILEID: fileName[swlog1.log], endPtr[48903]
configSize[64000], currentSize[64000], mode[1]
Time Stamp
Application
Level Log Message
------------------------+--------------+-------+--------------------------------
THU DEC 12 08:13:51 2002
THU DEC 12 08:13:53 2002
THU DEC 12 08:13:56 2002
THU DEC 12 08:13:56 2002
THU DEC 12 08:13:56 2002
THU DEC 12 08:13:56 2002
THU DEC 12 08:13:56 2002
THU DEC 12 08:13:56 2002
SYSTEM
SYSTEM
SYSTEM
info Switch Logging device ’swlog1.lt
info Switch Logging device ’swlog2.lt
info Switch Logging device ’/dev/cont
info == CSM == start up
info == CSM == Activating a new vers
info == CSM == The working version i
info == CSM == MONITORING ON
CSM-CHASSIS
CSM-CHASSIS
CSM-CHASSIS
CSM-CHASSIS
CSM-CHASSIS
info == CSM == This CMM is primary
After following the troubleshooting steps via CLI for physical connection, configuration validation,
system health and source learning, here are the additional commands in dshell to troubleshoot problems
related connectivity problem:
Checking the 7700/7800 Nantucket Fabric
nanlistB04
Certified: [Kernel]->nanListB04
No SOP Interrupt: 0
Multicast FIFO Full Interrupt: 0
Multicast Buffer Full Interrupt: 0
Unicast Buffer Full Interrupt: 0
Multicast Dump Interrupt: 0
Unicast Dump Interrupt: 0
Unicast Attempt Count: 8a620
Multicast Attempt Count: acecf
Unicast In Count: 8a627
Multicast In Count: acecf
Unicast Out Count: 8a634
Multicast Out Count: 3600e
Dummy Count: 61578
Total FLength Count: 0
value = 0 = 0x0
Certified: [Kernel]->
The total Flengtlh Count value should be 0 or a small value, a large value indicating that there are frames
being back up in the fabric queue.
page 2-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Switched Ethernet Connectivity
Using the Log File
Checking the 7700/7800 Nantucket Fabric for Interrupts, Data
Counts and Error Counts
Working: [Kernel]->nanListB02
HB Out of Sync Interrupts: 0
Error Count Exceeded Interrupts: 0
Framing Error Interrupts: 0
Parity Error Interrupts: 0
B02 Data Port 0 Frame Count = 690dbd37
B02 Data Port 1 Frame Count = 0
B02 Data Port 2 Frame Count = 542e70d9
B02 Data Port 3 Frame Count = 0
B02 Data Port 4 Frame Count = 0
B02 Data Port 5 Frame Count = 0
B02 Data Port 6 Frame Count = 0
B02 Data Port 7 Frame Count = 9e75d47
B02 Data Port 8 Frame Count = 690dbd39
B02 Data Port 9 Frame Count = 0
B02 Data Port 10 Frame Count = 542e70d9
B02 Data Port 11 Frame Count = 0
B02 Data Port 12 Frame Count = 0
B02 Data Port 13 Frame Count = 0
B02 Data Port 14 Frame Count = 0
B02 Data Port 15 Frame Count = 9e75d47
Checking the Traffic Queue on the NI
Working: [Kernel]->FindBuffer 3,0 => where 3 is the slot number
Queue = 0x62 length = 0x40, Address 0x6881880
Queue = 0x63 length = 0x40, Address 0x68818c0
value = 3 = 0x3
The above capture shows one of the queues is backed up on the NI. Check if the queue is sending traffic
using the following command syntax:
esmDumpCoronado slot,slice,address,bytes
Working: [Kernel]->esmDumpCoronado 3,0,0x6881880,20
6881880 :
40
68818a0 :
0
90
40
0
0
0
2f906d3
0
0
0
0
0
0
0
0
0
d8d0620
68818c0 :
value = 3 = 0x3
10090
2f906d3
Working: [Kernel]->esmDumpCoronado 3,0,0x6881880,20
6881880 :
40
68818a0 :
0
90
40
0
0
0
2f906d3
0
0
0
0
0
0
0
0
0
d8d0620
68818c0 :
value = 3 = 0x3
10090
2f906d3
The above capture shows the queue is stuck and not moving.
OmniSwitch Troubleshooting Guide September 2005
page 2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Log File
Troubleshooting Switched Ethernet Connectivity
Check for Catalina (MAC) or Port Lockup
Lab-Span1 > dshell
Working: [Kernel]->getNiResetCount
Slot 1, ASICResetCnt_p addr 0x2c3ee0
Slot 2, ASICResetCnt_p addr 0x2c3ee0
ENI HALF Duplex Reset count addr 0x2c3f60
phy 0:
0
0
0
0
0
0
0
0
0
0
0
0
phy 1:
0
0
0
0
PHY FIFO LOCKUP Reset count addr 0x2c3fc0
phy 0:
0
0
0
0
0
0
0
0
0
0
0
0
phy 1:
0
0
0
0
value = 0 = 0x0
Working: [Kernel]->
page 2-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Troubleshooting Source
Learning
In order to troubleshoot Source Learning problems, a basic understanding of the process is required.
A review of the “Managing Source Learning” chapter from the appropriate OmniSwitch Network Configu-
ration Guide is required. The following RFC and IEEE standards are supported:
RFCs supported
2674 - Definitions of Managed Objects for Bridges
with Traffic Classes, Multicast Filtering and
Virtual LAN Extensions
IEEE Standards supported
802.1Q - Virtual Bridged Local Area Networks
802.1D - Media Access Control Bridges
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Troubleshooting Source Learning
Introduction
VLAN 114
Port: 8/23
IP: 10.40.114.50
MAC:00-C0-4f-12-F7-1B
OmniSwitch 7800
VLAN 114
Port: 16/16
IP: 10.40.114.100
MAC: 00-10-A4-B5-B5-38
Source Learning Example
When a packet first arrives on NI source learning examines the packet and tries to classify the packet to
join its correct VLAN. If a port is statically defined in a VLAN, the MAC address is classified in the
default VLAN. Otherwise, if Group Mobility is being used the MAC address is classified into the correct
VLAN based on the rules defined.
As soon as the MAC address is classified in a VLAN, an entry is made in Source Address Pseudo-CAM
associating the MAC address with the VLAN ID and the Source Port. This Source Address is then relayed
to the CMM for management purposes.
If an entry already exists in MAC address database with the same VLAN ID and the same source port
number then no new entry is made. If VLAN ID or the source port is different from the existing entry in
MAC address database then the previous entry is aged out and a new entry is made in the MAC address
database. This process of adding a MAC address in the MAC address database is known as Source Learn-
ing.
A MAC address can be denied to learn on a port based on different policies configured through QOS or
Learned Port Security. A MAC address may be learned in a wrong VLAN based on the policies defined
for the port.
Note: This document does not discuss the basic operation of Source Learning. To learn about how Source
Learning works, refer to the “Managing Source Learning” in the appropriate OmniSwitch Network Config-
uration Guide.
page 3-2
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Source Learning
Troubleshooting a Source Learning Problem
Troubleshooting a Source Learning Problem
In order to troubleshoot a source learning problem the first step is to verify that the physical link is up and
the port has correctly auto-negotiated with the end-station.
The next thing is to verify that the port is a member of the right VLAN, if a port is statically configured
for a VLAN, or the Group Mobility policies are correctly defined. The workstation configuration should
also be verified.
The first thing to look for is the MAC address table to verify that the MAC address is being learned:
-> show mac-address-table
Vlan
Mac Address
Type
Protocol
Operation
Interface
------+-------------------+--------------+-----------+------------+-----------
105 00:00:5e:00:01:69
105 00:d0:95:6b:4c:d8
105 00:d0:95:79:62:eb
150 00:d0:95:6b:4c:e7
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
learned
10800
10800
10806
10800
10800
10800
10800
10800
10800
10806
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10800
10806
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
bridging
4/2
4/2
4/2
4/2
6/1
6/1
7/1
8/23
9/2
9/2
1
00:d0:95:79:65:ea
108 00:d0:95:6b:4c:db
110 00:d0:95:6b:4c:dd
114 00:c0:4f:12:f7:1b
112 00:d0:95:6b:4c:df
112 00:d0:95:79:65:10
50
50
51
51
52
52
53
53
54
54
55
55
56
56
57
57
58
58
59
59
60
60
61
61
62
62
00:00:5e:00:01:32
00:d0:95:83:e7:81
00:00:5e:00:01:33
00:d0:95:83:e7:82
00:00:5e:00:01:34
00:d0:95:83:e7:83
00:00:5e:00:01:35
00:d0:95:83:e7:84
00:00:5e:00:01:36
00:d0:95:83:e7:85
00:00:5e:00:01:37
00:d0:95:83:e7:86
00:00:5e:00:01:38
00:d0:95:83:e7:87
00:00:5e:00:01:39
00:d0:95:83:e7:88
00:00:5e:00:01:3a
00:d0:95:83:e7:89
00:00:5e:00:01:3b
00:d0:95:83:e7:8a
00:00:5e:00:01:3c
00:d0:95:83:e7:8b
00:00:5e:00:01:3d
00:d0:95:83:e7:8c
00:00:5e:00:01:3e
00:d0:95:83:e7:8d
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
11/1
16/16
114 00:10:a4:b5:b5:38
Total number of Valid MAC addresses above = 37
The above command shows all the MAC addresses learned by the switch.
OmniSwitch Troubleshooting Guide September 2005
page 3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting a Source Learning Problem
Troubleshooting Source Learning
In order to narrow down to a specific NI the following command can be used (any valid slot number can
be specified):
-> show mac-address-table slot 8
Legend: Mac Address: * = address not valid
Vlan
------+-------------------+--------------+-----------+------------+-----------
114 00:c0:4f:12:f7:1b learned 10800 bridging 8/23
Total number of Valid MAC addresses above = 1
Mac Address
Type
Protocol
Operation
Interface
This does show that the MAC address 00:c0:4f:12:f7:1b is learned on port 8/23, see the figure on page 3-2.
So, the source learning process for this workstation has been completed successfully.
Now, a single MAC address can be a member of multiple VLANs based on different protocols. To verify
that the MAC address has been learned in all of the VLANs, the above command can be used. The proto-
col field will be different based on different protocols being used and classified into different VLANs.
MAC addresses can also be viewed based on VLAN ID, using the following command:
->show mac-address-table 114
Legend: Mac Address: * = address not valid
Vlan
Mac Address
Type
Protocol
Operation
Interface
------+-------------------+--------------+-----------+------------+-----------
114 00:c0:4f:12:f7:1b
114 00:10:a4:b5:b5:38
learned
learned
10800
10806
bridging
bridging
8/23
16/16
Total number of Valid MAC addresses above = 2
The above command shows the two workstations learned in VLAN 114 on NI 8 and 16.
Whether it be a Layer 3 packet or layer 2, the first step is to have the source MAC address learned in the
MAC address table. Layer 3 involves resolution of ARP, for more details on ARP see troubleshooting
section of ARP, and then the available routes to the destination which involves routing, for more details on
Routing see troubleshooting section of Routing.
By default the MAC address aging time is set to 300 seconds. This can be viewed:
->show mac-address-table aging-time
Mac Address Aging Time (seconds) for Vlan 1 = 300
Mac Address Aging Time (seconds) for Vlan 114 = 300
This can be changed using the command:
->mac-address-table aging-time 500
Mac Address Aging Time (seconds) for Vlan 1 = 500
Mac Address Aging Time (seconds) for Vlan 114 = 500
This can also be changed on a particular VLAN:
->mac-address-table aging-time 600 vlan 114
It may be required to change the aging timer to a higher value to prevent the aging time of silent devices.
Another method by which silent devices can be accommodated is to use the permanent/static MAC
address assigned to a port using the command:
->mac-address-table permanent 00:10:a4:b5:b5:38 16/16 114
page 3-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Source Learning
Advanced Troubleshooting
Once, the MAC addresses are learned on the ports then the devices should be able to communicate
depending on the upper layers. Variations of MAC-related commands can be viewed in the “Managing
Source Learning” chapter from the appropriate OmniSwitch Network Configuration Guide.
Advanced Troubleshooting
The advanced troubleshooting for Source learning related problems is to look whether the traffic is
coming in from a port and the NI is not learning the MAC, if not prevented by using any other rules.
->debug ip packet board ni 8 start
R 8/23 00c04f12f71b->00d0957962c4 IP 10.40.114.50->10.40.114.2 ICMP 8,0
seq=58460.
8 S 8/23 00d0957962c4->00c04f12f71b IP 10.40.114.2->10.40.114.50 ICMP 0,0
seq=58460.
ebug ip 8 R 8/23 00c04f12f71b->00d0957962c4 IP 10.40.114.50->10.40.114.2 ICMP
8,0 seq=58716.
8 S 8/23 00d0957962c4->00c04f12f71b IP 10.40.114.2->10.40.114.50 ICMP 0,0
seq=58716.
packet 8 R 8/23 00c04f12f71b->00d0957962c4 IP 10.40.114.50->10.40.114.2 ICMP 8,0
seq=58972.
8 S 8/23 00d0957962c4->00c04f12f71b IP 10.40.114.2->10.40.114.50 ICMP 0,0
seq=58972.
stop8 R 8/23 00c04f12f71b->00d0957962c4 IP 10.40.114.50->10.40.114.2 ICMP 8,0
seq=59228.
8 S 8/23 00d0957962c4->00c04f12f71b IP 10.40.114.2->10.40.114.50 ICMP 0,0
seq=59228.
->debug ip packet stop
This command shows that the packets are coming into the switch and a reply is being sent by the switch to
the end station.
Various combinations of debug ip packet command can be used to find out the incoming traffic. The
combinations possible are as follows:
debug ip packet [start] [timeout seconds] [stop] [direction {in | out | all}] [format {header | text | all}]
[output {screen | switchlog}] [board {cmm | ni [1-16] | all | none} [ether-type {arp | ip | hex [hex] |
all}] [ip-address ip_address] [ip-pair [ip1] [ip2]] [protocol {tcp | udp | icmp | igmp | num [integer] |
all}] [show-broadcast {on | off}] show-multicast {on | off}]
start
Starts an IP packet debug session.
timeout
Sets the duration of the debug session, in seconds. To specify a dura-
tion for the debug session, enter timeout, then enter the session length.
seconds
The debug session length, in seconds.
Stops IP packet debug session.
Debugs incoming packets
stop
direction in
direction out
direction all
format header
Debugs outgoing packets.
Debugs both incoming and outgoing packets.
Debugs the packet header.
OmniSwitch Troubleshooting Guide September 2005
page 3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Troubleshooting
Troubleshooting Source Learning
format text
format all
Debugs the packet text.
Debugs the entire packet.
Output will appear on screen.
Output will be saved to a log file.
Debugs CMM packets.
output screen
output switchlog
board cmm
board ni
Debugs packets for a Network Interface (NI). To debug a specific inter-
face, enter ni, then enter the slot number of the NI.
board all
Debugs packets for all CMMs and NIs on the switch
Clears the previous board settings.
board none
If the problems are associated with the source learning on a specific NI then the limitations of the Number
of MAC addresses learned should also be considered. Current limitations are:
Number of learned MAC
addresses per network interface
(NI) module
32K
Number of learned MAC
addresses per switch
64K
The total number of MAC addresses learned per switch can be viewed using the command:
-> show mac-address-table count
Mac Address Table Count:
Permanent Address Count
= 0,
= 0,
= 0,
= 36,
= 36
DeleteOnReset Address Count
DeleteOnTimeout Address Count
Dynamic Learned Address Count
Total MAC Address In Use
If the problem is still not resolved then kindly contact Tech Support for further troubleshooting.
page 3-6
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Source Learning
Dshell Troubleshooting
Dshell Troubleshooting
The OmniSwitch 6/7/8XXX has a distributed architecture. Source Learning is specific to a NI. Each NI
has a layer 2 pseudo-cam which is which can hold 64K entries. 32K entries are reserved for L2 Source
Addresses which are local to that NI in L2SA table and the rest of 32K entries are reserved for L2 Destina-
tion Addresses which can be from local or remote NI in L2DA table.
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
If a problem is specific to a NI and the MAC address is not being learned by the switch, then the first step
is to verify from the pseudo-cam of that NI that the MAC address has been learned. There can be a possi-
bility that the NI has learned the MAC but CMM is not reporting that MAC because of IPC messages lost
between the CMM and NI.
The commands available to troubleshoot this problem are:
slcDumpL2SA: Display all the SA PseudoCAM entries on one slot/slice.
• Format: slcDumpL2SA slot_num, slice_num
slcDumpL2DA: Display all the Destination Address (DA) PseudoCAM entries on one slot/slice.
• Format: slcDumpL2DA slot_num, slice_num
slcLkupL2SA: Display the SA PCAM entries with MAC, VLAN) tuple on a slot/slice, the high 4 bytes of
MAC are MacHi, other 2 bytes are macLo, VLAN non-significant value is 0.
Format: slcLkupL2SA slot_num, slice_num, macHi, macLo, vlanId
slcLkupL2DA: Display the DA PCAM entries with (MAC, VLAN} tuple on a slot/slice, the high 4 bytes
of MAC are MacHi, other 2 bytes are macLo, VLAN non-significant value is 0.
• Format: slcLkupL2DA slot_num, slice_num, macHi, macLo, vlanId
Now, if device A connected on slot 8 is unable to communicate to device B in slot 16 then the following
steps can be taken to verify configuration on the NI
First look at the source MAC on slot 8 using the command:
Working: [Kernel]->slcDumpL2SA 8,0
Index
Mac Address
Vlan GlobalPort 4-words content
-------+-------------------+------+-----------+---------------------------------
----
0x371b 00:c0:4f:12:f7:1b 114
0000003a
250
007200c0 4f12f71b 00000000
Total L2 SA entry amount = 1
Look at the source MAC on slot 16:
Working: [Kernel]->slcDumpL2SA 16,0
Index
Mac Address
Vlan GlobalPort 4-words content
-------+-------------------+------+-----------+---------------------------------
----
0x3538 00:10:a4:b5:b5:38 114
499
00720010 a4b5b538 00000000
OmniSwitch Troubleshooting Guide September 2005
page 3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting Source Learning
000001f3
Total L2 SA entry amount = 1
Both of the MAC addresses are learned in the correct VLANs on the right NI.
Now, if device A is trying to communicate to device B then the next thing to look for is the destination
MAC address table. This is to verify that the destination MAC address table has the information about the
device B.
Working: [Kernel]->slcDumpL2DA 8,0
Index
Mac Address
Vlan GlobalPort 4-words content
-------+-------------------+------+-----------+---------------------------------
----
0x3004 00:20:da:00:70:04
00024000
1
0
00010020 da007004 c0004000
0x3538 00:10:a4:b5:b5:38 114
1f057f3
499
00720010 a4b5b538 00180000
So the entry do show up for the destination device.
Similarly for bidirectional traffic the entry should show up on slot 16.
Working: [Kernel]->slcDumpL2DA 16,0
Index
Mac Address
Vlan GlobalPort 4-words content
-------+-------------------+------+-----------+---------------------------------
----
0x3004 00:20:da:00:70:04
00024000
1
0
00010020 da007004 c0004000
0x371b 00:c0:4f:12:f7:1b 114
1f05b3a
250
007200c0 4f12f71b 00180000
So, the two devices should be able to communicate.
The L2SA and L2DA tables will be different for each slot. L2SA table will be based on the MAC address
learned on that slot. This will not be synchronized to all the other modules. Only the CMM will know
about it. When the request comes in from device A for device B, first a lookup is done on the local L2SA
and L2DA tables to see if there is a matching entry. If there is no matching entry then a request is sent on
the BBUS to all the other Coronados, if any Coronado has the matching entry in its L2SA table it responds
back with the Global port number of that entry. L2DA table is updated on the originating Coronado and
the packet is forwarded to the Global port to reach the destination.
If no other Coronado responds back to the request then the packet is sent over the flood queue to all the
other Coronado to be flooded out of the ports in the same VLAN. If a device responds back on the flooded
request, L2SA for that NI is updated and the Global port number is send to the originating device using the
same lookup as the response will be a unicast packet.
To see Source learning in action on an NI, set the debug level higher (levels are 1-6):
-> Sl_NiDebug=4
To see Source Learning in action on a CMM, set the debug level higher (levels are 1-6):
-> Sl_CmmDebug=5
To view the messages on the console, disable systrace:
-> Sl_no_systrace=1
The following is a sample output:
page 3-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Source Learning
Dshell Troubleshooting
Working: [Kernel]->Sl_no_systrace=1
Sl_no_systrace = 0x56402f4: value = 1 = 0x1
Working: [Kernel]->nidbg
3:0 nidbg> Sl_NiDebug=4
3:0
Sl_NiDebug = 0x2d1fc4: value = 4 = 0x4
3:0 nidbg> 3:0
3:0 ----------------------------- HRE PACKET HRADER -----------------------
3:0 isIPMS = 0, isSAMatched = 0, isDAMatched = 0, isMcst = 1, qId = 49, isRouted =
0, isTagged = 0, isFlood = 1, protoco
l = 0, sPort = 64
3:0 payLoadLength = 66, isLocked = 0, lockId = 0
3:0 isFBMsg = 0, isIPCMsg = 0, isSTPfrm = 0, isPrtTagged = 0, sVlanId = 21, reQId =
2, mcVlanId = 21
3:0 conditionCodes = 0x180, daMac = 0x00005e000115
3:0 saMac = 0x006008:91bb72, tagType = 0x8100, taginfo = 15, ethType = 800
3:0 ------------------------------ HRE PACKET HEADER END -----------------------
3:0
3:0 sln_salrn: gport = 64, vlanId = 21
3:0
SA 00:60:08:91:bb:72 successfully added to SA CAM
OmniSwitch Troubleshooting Guide September 2005
page 3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting Source Learning
OS-6600
To look at the forwarding database on OS-6600 in Dshell use the slcDumpSlotSlice command., which
displays which slot/slice is considered to be up and operational by the source learning software:
Certified: [Kernel]->slcDumpSlotSlice
Source Learning Slice Up List:
slot/slice 2/0, type = 838930434, firstgport = 64, lastgport = 123
value = 68 = 0x44 = ’D’
To look at the forwarding database on OS-6600 in Dshell use the dumpL2 command:
Certified: [Kernel]->dumpL2
Addr# VID
Addr
DN PN Age
AVID
-----------------------------------------------
00000 0001 00:01:02:03:00:00 00 30 STATIC xxxx
00001 0001 00:10:a4:f5:89:e2 03 00 DYNAMIC xxxx
00002 0002 00:00:5e:00:01:02 02 26 DYNAMIC xxxx
00003 0002 00:d0:95:84:07:1e 02 26 STATIC xxxx
00004 0003 00:00:5e:00:01:03 02 26 DYNAMIC xxxx
00005 0003 00:d0:95:84:07:1e 02 26 STATIC xxxx
00006 0004 00:d0:95:84:07:1e 02 26 STATIC xxxx
00007 0320 00:d0:95:84:3c:ce 02 01 DYNAMIC xxxx
00008 0333 00:d0:95:84:3c:ce 02 13 DYNAMIC xxxx
00009 0334 00:d0:95:82:12:ef 02 08 STATIC xxxx
00010 0334 00:d0:95:84:3c:ce 02 08 DYNAMIC xxxx
00011 0336 00:d0:95:79:64:ab 03 24 STATIC xxxx
00012 0340 00:d0:95:84:3c:ce 03 10 DYNAMIC xxxx
00013 0451 00:d0:95:84:3c:ce 03 11 DYNAMIC xxxx
00014 0999 00:00:5e:00:01:02 02 00 STATIC xxxx
00015 0999 00:00:c0:e0:29:e6 02 00 DYNAMIC xxxx
00016 0999 00:20:da:0a:54:10 02 00 STATIC xxxx
00017 0999 00:20:da:6c:20:4c 02 00 STATIC xxxx
00018 0999 00:90:27:17:f7:eb 02 00 STATIC xxxx
00019 0999 00:a0:24:d2:3f:cb 02 00 STATIC xxxx
Do you want to printf more addresses 0 -> No 1 -> Yes a -> all 1
Addr# VID Addr
DN PN Age
AVID
-----------------------------------------------
00020 0999 00:b0:d0:77:3e:3d 02 00 STATIC xxxx
00021 0999 00:d0:95:2a:02:4c 02 00 STATIC xxxx
00022 0999 00:d0:95:6a:84:51 02 00 STATIC xxxx
00023 0999 00:d0:95:84:3b:a0 02 00 DYNAMIC xxxx
00024 0999 00:d0:95:84:3d:90 02 00 DYNAMIC xxxx
00025 0999 00:d0:95:88:a7:28 02 00 STATIC xxxx
00026 0999 08:00:20:87:44:61 02 00 STATIC xxxx
No more addr in Master DB.
page 3-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Source Learning
Dshell Troubleshooting
L2 Physical Pool Stats:
Total Used
Free
16384
16384
2045
DstSwp Tables
NetID Tables
16384
16384
2046
0
0
1
Protocol Tables
ASIC Rsrc Wraps
2048
26
2022
value = 294 = 0x126
Output of many fields are described below:
output definitions
Addr
The index.
The VLAN ID.
VID
Addr
The MAC address learned.
The device number (stack number).
The port number.
DN
PN
Age
The MAC address type, which can be Dynamic or Static.
The Authenticated VLAN ID.
AVID
DstSwp Tables
NetID Tables
The entry for Next Hop info.
Contains transmit enables, prepend information, and address based
VLAN information.
To see Source learning in action, set the debug level higher (levels are 1-6):
SlnDebugLevel=1
The following is a sample output:
Certified: [Kernel]->SlnDebugLevel=1
SlnDebugLevel = 0x65c8af8: value = 1 = 0x1
=============== Start of CPU Unresolved Packet ===============
TxFlags = 0x2017, BufSize = 64, DiffservCodePoint = 0x0, CpuCode = 0x20, PrtclCode
= 0x1f, RxPNum = 10
PrepRxDevNum = 1, PrepRxPNum = 10, DstUnrCode = 0x1f, SrcUnrCode = 0x0, PacketRa-
mAddr = 0x68228
DstMacAddr16_48 = 0x3d9f8000, DstMacAddr0_15 = 0xe639
SrcMacAddr32_47 = 0x8000, SrcMacAddr0_31 = 0x180a539f
IPPayLoadOffset = 38, EnetType = 0x800, TagPriority = 1, TagVID = 3072
DstIPAddr = 0xc0a80b1b, SrcIPAddr = 0xc0a80b06
SrcIPSkt = 0x7f80, DstIPSkt = 0x7d00
hslnProcessL2Packet(258): vlanid = 0, gport = 42.
hsln_core_adrlrn_handler: Get the packet from Q-Dispatcher...
=======================
address pktPtr = 0x63e255c
queue_port_id = 0x402a
length = 60
lock = 0
packet_info = 0x0
ccode = 0x80
da = 00:80:9f:3d:50:b3
sa = 00:80:9f:53:0a:18
=== End of E_FRAME_PARAMS ===
OmniSwitch Troubleshooting Guide September 2005
page 3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting Source Learning
page 3-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Troubleshooting Spanning
Tree
In order to troubleshoot spanning tree related problems an understanding of the protocol and its features
are needed. The OmniSwitch supports two Spanning Tree Algorithms; 802.1D (standard) and 802.1w
(rapid reconfiguration). In addition, the Omniswitch supports two Spanning Tree operating modes: flat
(single STP instance per switch) and 1x1 (single STP instance per VLAN).
Spanning Tree Protocol is defined in the IEEE 802.1D standard.
The 802.1w amendment to that standard, Rapid Reconfiguration of Spanning Tree, improves upon STP by
providing rapid reconfiguration capability via Rapid Spanning Tree Protocol
For configuration assistance please read the “Configuring Spanning Tree Parameters” in the appropriate
OmniSwitch Network Configuration Guide.
In This Chapter
Introduction
The primary purpose for spanning tree is to allow for physical redundancy in a bridged network, while
assuring the absence of data loops. The protocol allows for dynamic fail-over as well.
One of the most important tools needed in troubleshooting a STP problem, is to be prepared before it
happens. It is essential to have a network diagram that depicts both the physical (cables) and logical
(VLANs) configurations. It also very useful to know which ports are normally in blocking/forwarding
prior to any problem.
OmniSwitch Troubleshooting Guide September 2005
page 4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Troubleshooting Spanning Tree
Troubleshooting Spanning Tree
A failure of the Spanning Tree Protocol (STP) will usually cause either a bridge loop on the LAN or
constant reconvergence of STP. This in turn can cause several resultant problems.
• If there is a bridge loop on the LAN, there can appear to be a broadcast storm since broadcast packets
will continuously loop the network. In addition, unicast traffic can be affected as the port a unicast
address is learned off of, can toggle from one port to another in a very short time period.
• If STP is constantly reconverging, this can cause temporary network outages as ports could through the
30 seconds of listening and learning as defined by 802.1D. One can see if STP is constantly reconverg-
ing that the LAN could be perpetually down.
In determining the cause of the STP problem, its useful to first verify the configuration, especially if the
network having problems has recently been installed.
Use the show spantree command to verify that STP is enabled and that both sides of the link are running
the same STP protocol.
-> show spantree
Vlan STP Status Protocol Priority
-----+----------+--------+--------
1
10
ON
ON
802.1D 32768
802.1D 32768
Use the show spantree command and specify a VLAN to verify the correct mode, designated root ID, root
port, and configurable timers. The timers need to be consistent across a physical link running STP. Also
very useful to note in this command are Topology changes and Topology age. If topology changes are
incrementing quickly, the LAN can not agree who is root. This can be caused by dropped BPDUs (which
will be discussed later), a bridge that insists it is root regardless of received BPDUs, or a physical link
going in and out of service.
-> show spantree 10
Spanning Tree Parameters for Vlan 10
Spanning Tree Status :
ON,
Protocol
:
IEEE 802.1D,
mode
Priority
: 1X1 (1 STP per Vlan),
: 32768 (0x8000),
Bridge ID
Designated Root
Cost to Root Bridge :
: 8000-00:d0:95:79:62:8a,
: 8000-00:d0:95:79:62:8a,
0,
Root Port
Next Best Root Cost :
Next Best Root Port :
Hold Time
Topology Changes
Topology age
:
None,
0,
None,
1,
:
:
:
0,
0:0:0
Current Parameters (seconds)
Max Age
Forward Delay
Hello Time
=
=
=
20,
15,
2
Parameters system uses when attempting to become root
System Max Age
System Forward Delay =
System Hello Time
=
20,
15,
2
=
page 4-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Troubleshooting Spanning Tree
Use the show spantree ports command to determine if the port is in forwarding or blocking and are in the
correct VLAN. Remember that in any LAN with physical redundancy there must be at least one port in
blocking status. If it is known which ports are usually in blocking, those ports can be a good place to start
to verify they are still in blocking status.
-> show spantree ports
Vlan Port Oper Status Path Cost Role
-----+-----+------------+---------+-----
10 5/10
FORW
100 DESG
If ports that should be in blocking are now in forwarding, there are two likely causes. The first is that there
was a physical failure in a link that was previously in forwarding. The second is that the BPDUs from the
root are being dropped. If it appears that BPDUs are being dropped, troubleshoot this as if it were any
other packet being dropped.
Use the show interfaces command to look for errors incrementing on the port as well as to verify duplex
settings match on either side of the link.
-> show interfaces 5/10
Slot/Port 5/10 :
Operational Status
Type
MAC address
: up,
: Fast Ethernet,
: 00:d0:95:7a:63:90,
BandWidth (Megabits) : 10,
Duplex
: Half,
Long Accept
: Enable,
Runt Accept
: Disable,
Long Frame Size(Bytes) : 1553,
Input :
Runt Size(Bytes) : 64
Bytes Received
Lost Frames
Unicast Frames
Broadcast Frames :
Multicast Frames :
UnderSize Frames :
OverSize Frames :
Collision Frames :
:
:
:
765702,
0,
2317,
3855,
480,
0,
0,
0,
Error Frames
:
0,
CRC Error Frames :
Alignments Error :
Output :
0,
0
Bytes transmitted :
566131,
0,
Lost Frames
Unicast Frames
:
:
2153,
8,
5931,
0,
Broadcast Frames :
Multicast Frames :
UnderSize Frames :
OverSize Frames :
Collision Frames :
0,
0,
Error Frames
:
0
OmniSwitch Troubleshooting Guide September 2005
page 4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Troubleshooting Spanning Tree
Since STP is run in a distributed fashion it is important to verify that each NI that is involved is not having
a resource problem. Use the show health command to verify the resources available on an NI.
-> show health 5
* - current value exceeds threshold
Slot 05
Resources
1 Min 1 Hr 1 Hr
Limit Curr Avg Avg Max
-----------------+-------+------+------+-----+----
Receive
Transmit/Receive
Memory
80
80
80
80
01
01
39
26
01
01
39
29
01
01
39
28
01
01
39
30
Cpu
If the problem has been ascertained to be layer 2 data loop, and it is needed to restore network connectiv-
ity quickly, it is recommended to disable all redundant links either administratively or by disconnecting
cables.
page 4-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Dshell
Dshell
As mentioned previously, it is important to verify the health of the NI as well as the CMM. Please refer to
Chapter 1, “Troubleshooting the Switch System,” for directions.
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
The commands run above to verify STP configuration on a particular port give the CMM perspective.
Since STP is run on the NI it is important to query the NI to verify what was seen from the CMM. To
verify a ports forwarding status use the esmDumpCoronado slot,slice, 0x6608000+vlan_id*4,32
command. This will indicate if the port as the NI sees it is in forwarding/blocking. The 32 in the above
command shows 32 register values starting from the vlan_id specified. If the vlan_id used is 1 then the
above command will display the values from VLAN 1 to VLAN 31. The bits are dedicated to the ports in
the following order, starting from least significant bit. The bits are set (value=1) to indicate that the ports
are forwarding for that VLAN. If 0 then the port is blocking for that VLAN.
Please note that the examples in this section have the following assumptions:
• Ports 1-12: First 12 Ethernet ports.
• Port 13: First Gigabit port.
• Ports 14,15,16: Not used.
• Ports 17-28: Second half of 12 Ethernet ports.
• Port 29: Second Gigabit port.
• Port 1/1 is a member of VLANs 1,140,141,150, and 511.
-> show vlan port 1/1
vlan
type
status
--------+---------+--------------
1
140
141
150
511
default forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
-> dshell
Working: [Kernel]->esmDumpCoronado 1,0,0x6608000+1*4,32
6608004 :
1000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
6608024 :
0
6608044 :
0
6608064 :
0
value = 1 = 0x1
OmniSwitch Troubleshooting Guide September 2005
page 4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell
Troubleshooting Spanning Tree
Working: [Kernel]->esmDumpCoronado 1,0,0x6608000+140*4,32
6608230 :
1000
1000
0
1000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
6608250 :
0
0
0
0
6608270 :
0
6608290 :
0
0
value = 1 = 0x1
Working: [Kernel]->esmDumpCoronado 1,0,0x6608000+511*4,32
66087fc :
1000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
660881c :
0
660883c :
0
660885c :
0
value = 1 = 0x1
The above commands that the spanning tree vector is set for Gigabit port 1/1 for VLANs 1, 140, 141, 150,
and 511.
Now, the following:
-> show vlan port 9/1
vlan
--------+---------+--------------
default forwarding
type
status
1
-> show vlan port 9/2
vlan type
--------+---------+--------------
default forwarding
status
1
-> show vlan port 9/24
vlan type
--------+---------+--------------
default forwarding
status
2
-> show vlan 3 port
port type
status
--------+---------+--------------
9/11 default forwarding
9/12 default forwarding
-> dshell
Working: [Kernel]->esmDumpCoronado 1,0,0x6608000+1*4,32
66087fc :
203
0
8000000
c00
0
0
0
0
660881c :
0
0
0
0
0
0
0
0
0
0
0
0
0
660883c :
0
page 4-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Dshell
0
660885c :
0
0
0
0
0
0
0
0
0
value = 1 = 0x1
Binary: 0000 0000 0011
For VLAN 1 the bits set are 203 which are equivalent to binary 0000 0000 0011. Bits 1 and 2 are set indi-
cating that ports 1 and 2 have the spanning tree vector set for VLAN 1. The next register value is for
VLAN 2, hex value is 8000000.
Binary: 1000 0000 0000 0000 0000 0000 0000
Binary value indicates that bit 28 is set which means that port 24 is set for VLAN 2. The next register
value will indicate the value for VLAN 3. Hex value is c00.
Binary: 1100 0000 0000
Bits 11 and 12 are set indicating that spanning tree has been set for ports 11 and 12. These ports are
forwarding.
Each NI when boots up sends a message to every other NI indicating that it is up and running. This
message is critical for setting up the port Queues to transfer data as well as for Spanning tree. If an IPC
message is lost by a particular NI then other NI will not see that NI as being a part of spanning tree
domain. This may result in split spanning tree leading to a layer 2 loop. This kind of scenario might
happen in the case of hot swaps.
To verify that each NI known about every other NI the following command should be used in NI Debug-
ger, This should be run on all NIs that are used in STP.
Working: [Kernel]->NiDebug
1:0 nidbg> stpNISock_boardupprint
1:0
1:0 STP boards up :
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
board in slot : 2 slice : 0 is up
board in slot : 4 slice : 0 is up
board in slot : 5 slice : 0 is up
board in slot : 6 slice : 0 is up
board in slot : 7 slice : 0 is up
board in slot : 8 slice : 0 is up
board in slot : 9 slice : 0 is up
board in slot : 10 slice : 0 is up
board in slot : 11 slice : 0 is up
board in slot : 12 slice : 0 is up
board in slot : 13 slice : 0 is up
board in slot : 14 slice : 0 is up
board in slot : 16 slice : 0 is up
1:0 value = 0 = 0x0
This command will show all the other slots except for itself.
To look at all the BPDUs being received and transmitted on a particular slot and slice the following
command can be used in NiDebug command. This will display, BPDUs as well as notifications when
there is a topology change in real time.
1:0 nidbg> stp_printf_flag=1
1:0 *** stpkern_bpduIn stp_id=511 portid=c type=2
1:0 PIM port c state 4 1024 0
OmniSwitch Troubleshooting Guide September 2005
page 4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell
Troubleshooting Spanning Tree
1:0 Message age of received BPDU : 0
1:0 PIM port c state 5 1024 0
1:0 recordProposed operPointToPointMAC=1
1:0 PIM port c state 7 1536 0
1:0 PIM port c state 4 1536 0
1:0 port 12 is forward (5)
1:0 tick (tack) time is now 701603
1:0
1:0 RSTBPDU transmitted on port 33
1:0 Root bridge ID = 3200d0 95820514
1:0 Path to Root cost = 3
on STP 57
1:0 Designated bridge ID = 800000d0 957962aa
1:0 Designated portId = 29697
1:0 Bridge
1:0 Message age
1:0 Proposing
1:0
portId = 29697
: 256
1:0 RSTBPDU transmitted on port 33
1:0 Root bridge ID = 3200d0 95820514
1:0 Path to Root cost = 3
on STP 51
1:0 Designated bridge ID = 800000d0 957962aa
1:0 Designated portId = 29697
1:0 Bridge
1:0 Message age
1:0 Proposing
portId = 29697
: 256
1:0 tick (tack) time is now 701628
1:0 tick (tack) time is now 701634
1:0 tick (tack) time is now 701635
1:0
1:0 RSTBPDU transmitted on port 33
1:0 Root bridge ID = 3200d0 95820514
1:0 Path to Root cost = 3
on STP 60
1:0 Designated bridge ID = 800000d0 957962aa
1:0 Designated portId = 29697
1:0 Bridge
1:0 Message age
1:0 Proposing
portId = 29697
: 256
1:0 tick (tack) time is now 701636
1:0
1:0 RSTBPDU transmitted on port 12
1:0 Root bridge ID = c800d0 957962aa
1:0 Path to Root cost = 0
on STP 140
1:0 Designated bridge ID = c800d0 957962aa
1:0 Designated portId = 29196
1:0 Bridge
1:0 Message age
portId = 29196
: 0
1:0 tick (tack) time is now 701637
1:0
1:0 RSTBPDU transmitted on port 33
1:0 Root bridge ID = 3200d0 95820514
1:0 Path to Root cost = 3
on STP 52
1:0 Designated bridge ID = 800000d0 957962aa
1:0 Designated portId = 29697
1:0 Bridge
1:0 Message age
1:0 Proposing
portId = 29697
: 256
1:0 RSTBPDU transmitted on port 33
1:0 Root bridge ID = 3200d0 95820514
1:0 Path to Root cost = 3
on STP 61
page 4-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Dshell
1:0 Designated bridge ID = 800000d0 957962aa
1:0 Designated portId = 29697
1:0 Bridge
1:0 Message age
1:0 Proposing
portId = 29697
: 256
1:0 tick (tack) time is now 701647
1:0 tick (tack) time is now 701648
1:0
1:0 RSTBPDU transmitted on port 33
1:0 Root bridge ID = 3200d0 95820514
1:0 Path to Root cost = 3
on STP 53
1:0 Designated bridge ID = 800000d0 957962aa
1:0 Designated portId = 29697
1:0 Bridge
1:0 Message age
1:0 Proposing
portId = 29697
: 256
OmniSwitch Troubleshooting Guide September 2005
page 4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Generic Troubleshooting in Dshell
Troubleshooting Spanning Tree
Generic Troubleshooting in Dshell
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
The stp_help command (executed from the NiDebug Dshell command prompt) displays the trace menu
for the Spanning Tree algorithm on NIs. Enter stpNI_help at ???? at what? Text missing here. ????
-> dshell
Working: [Kernel]->NiDebug
NiDebug>>stp_help
stpNISock_globals : Global variables
stpNISock_warningprint : warning trace
stpNISock_totraceprint : time-out trace
stpNISock_traceprint : event trace
stpNISock_intraceprint : inter-NI trace
stpNISock_boardupprint : boards up
stpNISock_printon : activates STP Socket Handler printf
stpNISock_printoff : desactivates STP Socket Handler printf
stpni_printStaFied : status field description trace
stpni_debugPport : Physical Port editing trace
stpni_debugLport : Logical Port editing trace
stpni_debugport : Physical & Logical Port editing trace
stpni_traceprint : event and warning trace
stpni_printon : activates STP NI printf
stpni_printoff : desactivates STP NI printf
These NI spanning tree trace utilities are described in the subsections that follow.
Event Trace (stpni_traceprint)
This trace includes the events received and generated by the Spanning Tree and the warning detected
while processing an event. A warning entry contains the name of the C source file and a line number. The
explanation of the warning can be given by Engineering.
Each event trace entry is built as follows:
• An ASCII pattern reflecting the event.
• Up to 4 parameters (a -1 (or 0xffffffff) indicates that the parameter is not significant).
The following is an example of the stpni_traceprint command printout:
Nidebug>> stpni_traceprint
64 - PVLANBLK (1,1000000,18,ffffffff)
65 - PORTATCH (19,1,ffffffff,ffffffff)
66 - PVLANBLK (1,2000000,19,ffffffff)
67 - PORTATCH (1a,1,ffffffff,ffffffff
68 - PVLANBLK (1,4000000,1a,ffffffff)
69 - PORTATCH (1b,1,ffffffff,ffffffff)
70 - PVLANBLK (1,8000000,1b,ffffffff)
71 - PORTATCH (1900001,1,ffffffff,ffffffff)
72 - PORTDELE (1,ffffffff,ffffffff,ffffffff)
73 - PORTATCH (1,1,ffffffff,ffffffff)
page 4-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Generic Troubleshooting in Dshell
74 - PORTDELE (2,ffffffff,ffffffff,ffffffff)
75 - PORTATCH (2,1,ffffffff,ffffffff)
76 - LINK_UP (1,64,1,ffffffff)
77 - LINK_UP (2,64,1,ffffffff)
78 - LINK_UP (14,64,1,ffffffff)
79 - LINKDOWN (1,ffffffff,ffffffff,ffffffff)
80 - LINKDOWN (2,ffffffff,ffffffff,ffffffff
81 - LINK_UP (1,64,1,ffffffff)
82 - LINK_UP (2,64,1,ffffffff)
83 - AGGR_UP (1,120,2e,ffffffff)
84 - Warning File:stpni_bpduEvt.c line:744
85 - PORTJOIN (1,121,ffffffff,ffffffff)
Event names displayed by the stpni_traceprint command are described in the subsections that follow.
PORTATCH
This corresponds to a port attached event received from the Spanning Tree CMM. The Spanning Tree
CMM generates this event when it receives a Port attach indication from the Port Manager.
The parameters are:
• First parameter: Global port identifier.
• Second parameter: Default VLAN associated to the port.
PORTDELE
This corresponds to a port detach event received from the Spanning Tree CMM. The Spanning Tree CMM
generates this event when either it receives a Port detach indication from the Port Manager or there is
change in the port type (e.g. transition from aggregable to fixed, mobile to fixed).
• First parameter: Global port identifier.
ADDVLAN
This event is generated by the Spanning Tree CMM when it receives a VLAN added event from the
VLAN Manager. This events is sent to all the NI that are up and running by the Spanning Tree CMM.
The parameters are:
• First parameter: The VLAN identifier.
• Second parameter: The Spanning Tree type. A 1 indicates Flat Spanning Tree while a 2 indicates 1x1
Spanning Tree.
• Third parameter: The VLAN administrative state. A 1 indicates Enable while a 2 indicates Disable.
• Fourth parameter: The Spanning Tree administrative state. A 1 indicates Enable while a 2 indicates
Disable.
OmniSwitch Troubleshooting Guide September 2005
page 4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Generic Troubleshooting in Dshell
Troubleshooting Spanning Tree
MODVLADM
This event is received is sent by the Spanning Tree CMM to the NIs when the administrative state of a
VLAN is changed (event generated by the VLAN Manager to the Spanning Tree CMM).
The parameters are:
• First parameter: The VLAN identifier.
• Second parameter: The VLAN administrative state. A 1 indicates Enable while a 2 indicates Disable.
MODVLSTP
This event is received is sent by the Spanning Tree CMM to the NIs when the Spanning Tree state of a
VLAN is changed (event generated by the VLAN Manager to the Spanning Tree CMM).
The parameters are:
• First parameter: The VLAN identifier.
• Second parameter: New Spanning Tree. A 1 indicates Enable while a 2 indicates Disable.
Note. When the Spanning Tree state is Disable, all the ports (Up) are moved to the forwarding state and
are removed from the Spanning Tree scope.
ADDQTAG
This event is received is sent by the Spanning Tree CMM to the NI when a tag is added to a port belong-
ing to that NI. This event is generated on the CMM by the 802.1Q application.
The parameters are:
• First parameter: Global port identifier.
• Second parameter: The 802.1Q tag.
Note. This event is processed by the Spanning Tree NI as a port attach event.
DELQTAG
This event is received is sent by the Spanning Tree CMM to the NI when a tag is removed a port belong-
ing to that NI. This event is generated on the CMM by the 802.1q application.
The single parameters is:
• First parameter: Global port identifier.
Note. This event is processed by the Spanning Tree NI as a port attach event.
page 4-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Generic Troubleshooting in Dshell
MDEFVLAN
This event is received is sent by the Spanning Tree CMM to the NI when the default VLAN of a fixed or
q-tagged port is change (this also applies to logical port). This event is generated on the CMM by VLAN
Manager application.
The parameters are:
• First parameter: Global port identifier.
• Second parameter: new default VLAN.
PORTAGGR
This event is currently unused.
PORTDISG
This event is currently unused.
AGGR_UP
This event is sent by Link Aggregation NI when it detects that a aggregator comes up; It could be either a
static aggregator (OmniChannel) or a dynamic aggregator (802.3ad). This message is generated when the
first port joins the aggregator only.
The parameters are:
• First parameter: The aggregator identifier (logical port ID value between 0 and 31).
• Second parameter: The global port identifier of the physical port that has joined the aggregator.
• Third parameter: The output QID to be used by the Spanning Tree (not significant).
Note. The output QID is no more used by the Spanning Tree since at the time Link aggregation is asking
for the default queue associated to the physical port, Qdriver might not be ready the provide it. However
Link Aggregation keeps providing this parameter even if now this one is not significant.
AGGRDOWN
This event is sent by Link Aggregation NI when it detects that a aggregator goes down; It could be either a
static aggregator (OmniChannel) or a dynamic aggregator (802.3ad). This message is generated when the
last port has leaved the aggregator.
The single parameter is:
• First parameter: The aggregator identifier (logical port ID value between 0 and 31).
OmniSwitch Troubleshooting Guide September 2005
page 4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Generic Troubleshooting in Dshell
Troubleshooting Spanning Tree
PORTJOIN
This event is sent by Link Aggregation NI when a physical port is joining an aggregator; It could be either
a static aggregator (OmniChannel) or a dynamic aggregator (802.3ad). This message is generated after the
The parameters are:
• First parameter: The aggregator identifier (logical port ID value between 0 and 31).
• Second parameter: The global port identifier of the physical port that has joined the aggregator.
PORTLEAV
This event is sent by Link Aggregation NI when a physical port is leaving an aggregator; It could be either
a static aggregator (OmniChannel) or a dynamic aggregator (802.3ad). This message is generated after the
first port has joined the aggregator (see “AGGR_UP” on page 4-13). Link aggregation provides the aggre-
gator identifier, the global port identifier of the port which is leaving it and the global port identifier of the
newly primary port
The parameters are:
• First parameter: The aggregator identifier (logical port ID value between 0 and 31).
• Second parameter: The global port identifier of the physical port that has joined the aggregator.
• Third parameter: The global port identifier of the physical port that will have the primary port role.
• Fourth parameter: The output QID of the newly primary port (not significant; see note of “AGGR_UP”
BRGPARAM
The is event is generated by the Spanning Tree CMM when a configuration parameter of the Spanning
Tree is changed by the operator. This message is sent to all the NI that are up and running.
The parameters are:
• First parameter: The spanning identifier (i.e., VLAN identifier).
• Second parameter: The type of the parameter. A 1 indicates Spanning Protocol (802.1w(third parame-
ter=4)/802.1D(third parameter=3)), a 2 indicates Spanning Tree (Flat (third parameter=1)/ or 1x1 (third
parameter=2)/), a 3 indicates the bridge priority value, a 4 indicates the Hello timer value, and a 5 indi-
cates the forward delay value, and a 6 indicates the maximum age.
• Third parameter: The value of the parameter.
page 4-14
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Generic Troubleshooting in Dshell
PTSTPMOD
The is event is generated by the Spanning Tree CMM when the Spanning Tree configuration parameter of
a port is changed by the operator.
The parameters are:
• First parameter: The spanning identifier (i.e., VLAN identifier).
• Second parameter: The global port identifier.
• Third and fourth parameters: The type of the parameter/value. A 0x11 indicates mode of the port
(dynamic(1), blocking(2), forwarding(3)), a 0x12 indicates Spanning Tree administrative state of the
port (enable(1),disable(2)), a 0x13 indicates port administrative state, a 0x14 indicates port priority, a
0x15 indicates port path cost, and a 0x16 indicates port connection type (half-duplex(1),point to point
(2),auto point to point(3),edge(4)).
PORTMOD
The is event is sent by the Spanning Tree CMM to the Spanning Tree NI when the administrative state of
a port is modified by the operator.
The parameters are:
• First parameter: The spanning identifier (i.e., VLAN identifier).
• Second parameter: The global port identifier.
• Third and fourth parameters: The type of the parameter/value. A 0x13 indicates port administrative
state (enable (1),disable(2)).
PORTVLBK
This event is an internal event which generated by the Spanning Tree when STP is processing a Port/
VLAN blocking that can take place at VLAN level or port level.
The parameters are:
• First parameter: The blocking status. A 0x44 indicates blocking already done, a 0x88 indicates nothing
to do, a 0x55 indicates blocking at port level, and a 0xaa indicates blocking at VLAN level.
• Second parameter: The local port identifier.
• Third parameter: The VLAN identifier.
PVLANBLK
This event is registered when the Spanning Tree is generated a Port VLAN Blocking message to Source
Learning NI.
The parameters are:
• First parameter: The VLAN identifier.
• Second parameter: The port vector.
• Third parameter: The local port identifier.
OmniSwitch Troubleshooting Guide September 2005
page 4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Generic Troubleshooting in Dshell
Troubleshooting Spanning Tree
The Port VLAN blocking message sent to the Source Learning NI has the following structure:
uint16 VlanId, uint32 PortVector
This event has the following values for the message ID:
• appID: APPID_SPANNING_TREE.
• subMsgNum: STP_PortVlanBlocking.
These event fields are defined below:
• VlanId: A value 1 to 4095 identifies a VLAN (0 means that the message is applied to ports defined by
the PortVector on all VLANs).
• PortVector: A field of bits, one bit by the physical port, which indicates if the port is concerned by the
change of state.
GMBPDU
This message is sent by the Spanning tree NI to the local Group Mobility NI each time a BPDU is received
on a mobile port. Group mobility can take two actions depending on how the mobile port has been config-
ured:
• Ignore BPDU: In this case Spanning Tree will keep on sending GMBPDU each time a BPDU will be
received on the port (there is no Spanning Tree computation for the port).
• Move port to fixed: Group Mobility asks Spanning Tree to revert the mobile port to the fixed state and
the port will be added to Spanning Tree associated to VLAN 1.
The BPDUonMobPort message sent by the Spanning Tree NI has the following format:
uint8 LocalPortId, uint8 bpdu_lgth, uint8 bpdu_data[STP_BPDULGTH]
This event has the following values for the message ID:
• appID: APPID_SPANNING_TREE
• subMsgNum: STP_BPDUonMobPort
These event fields are defined below:
• LocalPortId: Identifies the physical Port (local reference: 0 to 23) which received the BPDU.
• bpdu_lgth: The length in bytes of the following BPDU.
• bpdu_data: The BPDU.
GMIGBPDU
This message is sent by Group Mobility NI in response to a BPDU on mobile port message sent by the
Spanning Tree. By sending this message group mobility tells to Spanning Tree to ignore BPDU on the
mobile port.
The single parameters is:
• First parameter: The global port identifier.
page 4-16
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Generic Troubleshooting in Dshell
GM2FIXED
This message is sent by Group Mobility NI in response to a BPDU on mobile port message sent by the
Spanning Tree. By sending this message group mobility tells to Spanning Tree that the mobile port must
be reverted to the fixed state.
The parameters are:
• First parameter: The global port identifier.
• Second parameter: The default VLAN.
VMADDVPA
The event is sent by the VLAN manager NI when a new VLAN needs to be added to a mobile port (no
longer used by the VLAN manager).
The parameters are:
• First parameter: The global port identifier.
• Second parameter: The default VLAN.
VMDELVPA
The event is sent by the VLAN manager NI when a VLAN needs to be removed from a mobile port (no
more used by VLAN manager).
The parameters are:
• First parameter: The global port identifier.
• Second parameter: The default VLAN.
VMDEFVPA
The event is sent by the VLAN manager NI when a the default VLAN of a mobile port needs to be
changed.
The parameters are:
• First parameter: The global port identifier.
• Second parameter: The default VLAN.
OmniSwitch Troubleshooting Guide September 2005
page 4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Generic Troubleshooting in Dshell
Troubleshooting Spanning Tree
TOPOCHGT
This event notifies a change of Spanning Tree topology. The format of the message is:
uint16 VlanId, uint16 aging_timer
This event has the following values for the message ID:
• appID: APPID_SPANNING_TREE
• subMsgNum: STP_TopologyChange
These event fields are defined below:
• VlanId: A value of 1 to 4095 identifies a VLAN and 0 means that the message is applied to all the
VLANs (single Spanning Tree per switch).
• aging_timer: The value in second of the aging timer.
LINK_UP
This event is sent by the ENI driver when a link goes up.
The parameters are:
• First parameter: The global port identifier.
• Second parameter: The default link bandwidth.
• Third parameter: The link mode (full-duplex(1),half-duplex(2),auto-negociate(3)).
LINKDOWN
This event is sent by the ENI driver when a link goes down.
The parameters are:
• First parameter: The global port identifier.
NI_UP
This event is sent by NI Supervision when it detects that a new NI is up and running.
The parameters are:
• First parameter: The slot number.
• Second parameter: The slice number.
NI_DOWN
This event is sent by NI Supervision when it detects that a new NI is up and running.
The parameters are:
• First parameter: The slot number.
• Second parameter: The slice number.
page 4-18
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Generic Troubleshooting in Dshell
Physical and Logical Port Dumps
Logical Ports (stpni_debugLport)
Here follows the display of the Logical port seen by the Spanning Tree. Each line corresponds to the local
port identifier index.
Certified: [Kernel]->stpni_debugLport
Logical Ports array:
sta field:
- 0x80 -> 1:Point to point Port
- 0x20 -> 1:Aggregable port
- 0x02 -> 1:Link up ; 0:link Down
- 0x01 -> 1:Adm up ; 0:Adm Down
- 0x04 -> Fixed Port
- 0x08 -> Q-tagged Port
- 0x10 -> Mobile Port
sta dGid qid portid nTag vector Prim Mac Address
Bw Duplex
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
0b 0001 0233 01900001 0001 00000000 03000000 38 00:00:00:00:00:00 03e8 00
0b 0001 0187 01900002 0001 00000300 00000000 09 00:00:00:00:00:00 0064 00
0b 0001 01cb 01900003 0003 0c000000 00000000 1a 00:00:00:00:00:00 03e8 00
0b 0001 01a3 01900004 0001 00030000 00000000 10 00:00:00:00:00:00 0064 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 00000000 00000000 ff 00:00:00:00:00:00 0000 00
value = 9 = 0x9
OmniSwitch Troubleshooting Guide September 2005
page 4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Generic Troubleshooting in Dshell
Troubleshooting Spanning Tree
The fields displayed by the stpni_debugLport command are described below:
output definitions
dGid
The field contains the value of the default VLAN associated to the port.
When the default GID is 0, it indicates that the port is in the IDLE state
(field sta=00).
Qid
Default QID (not used).
Portid
Global port identifier (0x0190xxxx indicates that it is a logical port, and
0x0001 indicates that it is logical port 1).
NTag
Number of tags (802.1q) attached to that port. This field should always
be 0 when the port is FIXED or MOBILE.
Vector
Bitmap of the local ports that belong to the aggregator (logical port). In
the example local port 1 and 2 belong to the aggregator (MSB= port 31
and LSB = port 0).
Prim
Local port identifier of the primary port. If the primary port does not
belong to that NI, the primary reference is set to 0xff.
Bw
Bandwidth as received on Link up from the ENI driver.
Duplex mode as received from ENI driver on Link Up.
Duplex
Physical Port (stpni_debugPport)
Here is the display of the Physical Port seen by the Spanning Tree NI:
Certified: [Kernel]->stpni_debugPport
Physical Ports array:
sta field:
- 0x80 -> 1:Point to point Port
- 0x20 -> 1:Aggregable port
- 0x02 -> 1:Link up ; 0:link Down
- 0x01 -> 1:Adm up ; 0:Adm Down
- 0x04 -> Fixed Port
- 0x08 -> Q-tagged Port
- 0x10 -> Mobile Port
sta dGid qid portid nTag lpid prim Mac Address
Bw Duplex
07 03e7 0162 00000040 0000 ff ff 00:d0:95:84:3c:d0 0064 00
07 0140 0166 00000041 0000 ff ff 00:d0:95:84:3c:d1 0064 01
05 0001 016a 00000042 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 016e 00000043 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 0172 00000044 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 0176 00000045 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 017a 00000046 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 017e 00000047 0000 ff ff 00:00:00:00:00:00 0000 00
23 0000 0182 00000048 0000 82 ff 00:d0:95:84:3c:d8 0064 01
23 0000 0186 00000049 0000 82 ff 00:d0:95:84:3c:d9 0064 01
05 0001 018a 0000004a 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 018e 0000004b 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 0192 0000004c 0000 ff ff 00:00:00:00:00:00 0000 00
07 014d 0196 0000004d 0000 ff ff 00:d0:95:84:3c:dd 0064 01
05 0001 019a 0000004e 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 019e 0000004f 0000 ff ff 00:00:00:00:00:00 0000 00
23 0000 01a2 00000050 0000 84 ff 00:d0:95:84:3c:e0 0064 01
page 4-20
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Generic Troubleshooting in Dshell
23 0000 01a6 00000051 0000 84 ff 00:d0:95:84:3c:e1 0064 01
05 0001 01aa 00000052 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01ae 00000053 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01b2 00000054 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01b6 00000055 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01ba 00000056 0000 ff ff 00:00:00:00:00:00 0000 00
0b 0001 01be 00000057 0003 ff ff 00:d0:95:84:3c:e7 0064 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
23 0000 01ca 0000005a 0000 83 ff 00:d0:95:84:3d:02 03e8 01
23 0000 01ce 0000005b 0000 83 ff 00:d0:95:84:3d:03 03e8 01
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
07 0001 01d2 00000060 0000 ff ff 00:d0:95:84:3c:e8 000a 00
05 0001 01d6 00000061 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01da 00000062 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01de 00000063 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01e2 00000064 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01e6 00000065 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01ea 00000066 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01ee 00000067 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01f2 00000068 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 01f6 00000069 0000 ff ff 00:00:00:00:00:00 0000 00
07 0154 01fa 0000006a 0000 ff ff 00:d0:95:84:3c:f2 0064 01
07 01c3 01fe 0000006b 0000 ff ff 00:d0:95:84:3c:f3 0064 01
05 0001 0202 0000006c 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 0206 0000006d 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 020a 0000006e 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 020e 0000006f 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 0212 00000070 0000 ff ff 00:00:00:00:00:00 0000 00
07 0002 0216 00000071 0000 ff ff 00:d0:95:84:3c:f9 0064 01
05 0001 021a 00000072 0000 ff ff 00:00:00:00:00:00 0000 00
07 0003 021e 00000073 0000 ff ff 00:d0:95:84:3c:fb 0064 01
05 0001 0222 00000074 0000 ff ff 00:00:00:00:00:00 0000 00
07 0004 0226 00000075 0000 ff ff 00:d0:95:84:3c:fd 0064 01
05 0001 022a 00000076 0000 ff ff 00:00:00:00:00:00 0000 00
05 0001 022e 00000077 0000 ff ff 00:00:00:00:00:00 0000 00
23 0000 0232 00000078 0000 81 ff 00:d0:95:84:3d:00 03e8 01
23 0000 0236 00000079 0000 81 ff 00:d0:95:84:3d:01 03e8 01
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
00 0000 0000 00000000 0000 ff ff 00:00:00:00:00:00 0000 00
value = 9 = 0x9
The fields displayed by the stpni_debugPport command are described below:
output definitions
dGid
Qid
The field contains the value of the default VLAN associated to the port.
When the default GID is 0, it indicates that the port is in the IDLE state
(field sta=00).
The information displayed for the QID is significant if the Link up bit is
set (sta field).
OmniSwitch Troubleshooting Guide September 2005
page 4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Generic Troubleshooting in Dshell
Troubleshooting Spanning Tree
output definitions (continued)
Portid
Global port identifier (0x0190xxxx indicates that it is a logical port, and
0x0001 indicates that it is logical port 1).
NTag
Number of tags (802.1q) attached to that port. This field should always
be 0 when the port is FIXED or MOBILE.
Vector
Bitmap of the local ports that belong to the aggregator (logical port). In
the example local port 1 and 2 belong to the aggregator (MSB= port 31
and LSB = port 0).
lpid
Local port identifier of the logical port to which to physical port is
bounded. In the current display, it indicates that physical ports 1 and 2
are bounded to logical port 1 (0x81). Within the Spanning Tree NI, a
logical port type is identified by setting bit 7 to 1 in the local port (1
byte field). This field is not significant if the port is not aggregable (see
the interpretation of the sta field in the display).
Prim
Bw
Not significant for the physical port.
Bandwidth as received on Link up from the ENI driver.
Duplex mode as received from ENI driver on Link Up.
Duplex
Physical and Logical Port Trace Display (stpni_debugport)
This is a combination of the Logical and Physical port display. See “Logical Ports (stpni_debugLport)” on
Socket Handler Traces
These traces include Global data, warning, and event traces. They are implemented on the CMM and NI.
These traces are listed below and described in the following subsections:
stpNISock_globals
Global variables.
stpNISock_warningprint
stpNISock_totraceprint
stpNISock_traceprint
stpNISock_intraceprint
stpNISock_boardupprint
stpNISock_printon
Warning trace.
Time-out trace.
Event trace.
Inter-NI trace.
Boards seen alive by the Socket Handler.
Activates STP Socket Handler printf.
Deactivates STP Socket Handler printf.
stpNISock_printoff
stpNISock_globals
This trace handles the Socket Handler. Its components are listed below:
• sockGlobal_protThreshold: This parameter is the maximum number of message that can be
processed consecutively on the Protocol Manager channel (CMM/NI STP channel).
• sockGlobal_maxmsgprot: This counter is the maximum number of message (counter) processed
consecutively on the Protocol Manager channel (CMM/NI STP channel).
• sockGlobal_evtThreshold: This parameter is the maximum number of message that can be processed
consecutively on the Message Event Manager channel (inter-NI STP channel).
page 4-22
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Generic Troubleshooting in Dshell
• sockGlobal_maxmsgevt: This counter is the maximum number of message (counter) processed
consecutively on the Message Event Manager channel (inter-NI STP channel).
• sockGlobal_looptick: This flag is set to 1 indicates that we loop until the maximum number of
message processed (Threshold) is overtaken.
• sockGlobal_maxtick: This counter is the maximum number of ticks processed consecutively.
• sockGlobal_maxtickact: This parameter is the maximum number of times the function attached to the
tick can be called consecutively.
• sockGlobal_tmoval: This parameter is the value of the time-out for retry mechanism.
• sockGlobal_localchannelevt: This counter is the number of message received on the Message event
channel (inter-NI STP channel).
• sockGlobal_localchannelservice: This counter is the number of message received on the service chan-
nel.
stpNISock_warningprint
A warning entry contains the name of the C source file and a line number. The explanation of the warning
is found in the STP Socket Handler source code:
/home/perforce/xxxx/engr/sw/bridging/spanning_tree/common/src/stp_sockHdl.c
stpNISock_traceprint
This trace records all the event received by the Socket Handler. This following is a sample output:
Trace Index : 4
remote_addr : 3 0 12 20
msg -> 0 or ack -> 1 : 1 seqID : 2
message ID : 0
Trace Index : 5
remote_addr : 3 0 12 20
msg -> 0 or ack -> 1 : 0 seqID : 2
message ID : c00ab
This trace displays the following parameters:
output definitions
Remote_addr
Consists of the transmitting slot, transmitting slice, transmitting AppId,
transmitting SnapId.
msg or ack
seqID
A 0 indicates a message while a 1 indicates an acknowledgement.
The sequence identifier of the message or acknowledgement.
message ID
The first word consists of the AppId of the transmitting application.
The last word consists of an event identifier message or acknowledge-
ment and sequence identifier parameters, which appear only in case of
reliable mode. The reliable mode concerns only the Protocol Manager
(CMM/NI STP) and Message event Manager (inter-NI STP) channels.
OmniSwitch Troubleshooting Guide September 2005
page 4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Generic Troubleshooting in Dshell
Troubleshooting Spanning Tree
Inter-NI Trace (stpNISock_intraceprint)
This trace records all the inter-NI STP events received by the Socket Handler and has the following
format:
• An ASCII pattern reflecting the event.
• Up to 4 parameters (a -1 (or 0xffffffff) indicates that the parameter is not significant).
Time-out Trace (stpNISock_totraceprint)
This trace records all the time-out on the Protocol Manager channel (CMM/NI STP channel) and the
Message Event Manager channel (inter-NI STP channel). The following is a sample output:
Trace Index : 1
Slot : 255 Slice : 255 seqID : 1 eventID : 25
currentretry : 0 maxretry : 31
This trace displays the following parameters:
output definitions
Slot
Slot of the transmitting processor.
Slice of the transmitting processor.
The message sequence identifier.
The event identifier.
Slice
seqID
EventID
Currentretry
Maxretry
The number of time-out always appeared.
The maximum time-out allowed.
Board Up (stpNISock_boardupprint)
This trace indicates the boards seen alive by the Socket Handler.
stpNISock_printon
This trace activates the printf of the following traces:
• Warning trace.
• Time-out trace.
• Event trace.
• Inter-NI trace.
StpNISock_printoff
page 4-24
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Generic Troubleshooting in Dshell
CMM Spanning Tree Traces
Trace Menu
The stpCMMSock_help Dshell command displays the Spanning Tree Manager menu as shown below.
-> dshell
Certified: [Kernel]->stpCMMSock_help
CMM
Slot : 65
Slice : 0
stpCMMSock_globals
: Global variables
: warning trace
: time-out trace
: event trace
stpCMMSock_warningprint
stpCMMSock_totraceprint
stpCMMSock_traceprint
stpCMMSock_ttimetraceprint : treatment time trace
stpCMMSock_boardupprint
stpCMMSock_printon
stpCMMSock_printoff
stpCMMSock_bufferprint
value = 0 = 0x0
: boards up
: activates STP Socket Handler printf
: desactivates STP Socket Handler printf
: internal buffer statistics
stpCMM_traceprint
The following is an example of the stpCMM_traceprint trace display:
Certified: [Kernel]->stpCMM_traceprint
********** STP CMM TRACE **********
1 PSMREG 0 0 0
2 MACADDR 0 0 0
3 BOARDUP 1 1 302059521
4 MSGtoNI 9 1 0
5 MSGtoNI 14 1 0
6 MSGtoNI 9 1 0
7 PMATTCH 0 0 0
8 MSGtoNI 21 1 0
9 PMATTCH 1 0 0
10 MSGtoNI 21 1 0
11 PMATTCH 2 0 0
12 MSGtoNI 21 1 0
13 PMATTCH 3 0 0
14 MSGtoNI 21 1 0
15 PMATTCH 4 0 0
OmniSwitch Troubleshooting Guide September 2005
page 4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Writing a PR for Spanning Tree
Troubleshooting Spanning Tree
Writing a PR for Spanning Tree
The following subsections describe some guidelines to follow when writing a PR that addresses Spanning
Tree. Please note that the following subsections use Dshell commands, not CLI commands.
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
Exception in Spanning Tree (NI and CMM case)
When there is an exception in a task, the task is suspended by the Operating system. This could happen
when the application tries to access to an un-aligned memory area, release of buffer that is already release,
etc. If the Spanning Tree does not respond, ask for the task information (i Dshell command). If the task is
suspended do the following:
1 Get the task registers with the ti task_id command.
2 Get the task stack with the tt task_id command.
3 Disassemble the code around the faulty PC (exception program counter).
Note. Perform the step above between address - 0x20 and address+0x100.
Port Does Not Forward
If the show spanning tree command indicates that the port is forwarding, but no traffic is seen through that
port do the following:
1 Perform the following steps on the NI:
a Select the suspected NI (changeSlot).
b Dump the event trace (stpni_traceprint).
c Dump the port trace (stpni_debugport).
2 Perform the following steps on the CMM.
a Dump the event trace.
b Dump the Spanning Tree memory for the VLAN (0x6608000+(vlan_id*4))
page 4-26
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Spanning Tree
Writing a PR for Spanning Tree
Spanning Tree Unchanged When Port State Has Changed
If the show spanning tree CLI command still displays the same information while a port state has changed
then the problem could be due to a broken communication path between the CMM and NI. In this case do
the following (for both the CMM and NI):
• Time-out trace of the socket handler (stpNISock_totraceprint or stpCMMSock_totraceprint).
• Warning trace of the socket handler (stpNISock_warningprint or stpCMMSock_warningprint).
• Event trace (stpni_traceprint and stpCMM_traceprint).
• Board-up trace (stpNISock_boardupprint or stpCMMSock_boardupprint).
Other Cases
For analysis of Spanning Tree on an NI do the following:
• Event trace (stpni_traceprint).
• Dump the port trace (stpni_debugport).
• Time-out trace of the socket handler (stpNISock_totraceprint or stpCMMSock_totraceprint).
• Warning trace of the socket handler (stpNISock_warningprint or stpCMMSock_warningprint).
• Inter-NI trace: (stpNISock_intraceprint).
• Boards seen alive by the Socket Handler (stpNISock_boardupprint or
stpCMMSock_boardupprint).
For analysis of Spanning Tree on a CMM do the following:
• Event trace (stpCMM_traceprint).
• Time-out trace of the socket handler (stpNISock_totraceprint or stpCMMSock_totraceprint).
• Warning trace of the socket handler (stpNISock_warningprint or stpCMMSock_warningprint).
• Boards seen alive by the Socket Handler (stpNISock_boardupprint or
stpCMMSock_boardupprint).
OmniSwitch Troubleshooting Guide September 2005
page 4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Writing a PR for Spanning Tree
Troubleshooting Spanning Tree
page 4-28
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting BOOTP/
DHCP/UDP Relay
In order to troubleshoot a BOOTP/DHCP and UDP Relay, a basic understanding of the protocol is
required. Some basic concepts are covered below. The OmniSwitch supports UDP Relay.
Reading the “DHCP Relay” chapter from the appropriate OmniSwitch Network Configuration Guide is
also highly recommended.
In This Chapter
Starting the Troubleshooting Procedure
There are two key ingredients for any troubleshooting episode. These are:
• Network Diagram.
• OSI Model.
OmniSwitch Troubleshooting Guide September 2005
page 5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting the Troubleshooting Procedure
Troubleshooting BOOTP/DHCP/UDP Relay
Use a Network Diagram
It is extremely important to know where the server is in relation to the client, which switch both the client
and the server is directly connected to and their port numbers. A network diagram presents this kind of
information, for example, in an easily understood matter.
VLAN 10
DHCP Server
IP Address: 10.10.10.58
OmniSwitch 7800
Switch VLAN IP Addresses:
10.10.10.200
20.20.20.200
Client
Client
VLAN 20
Sample Diagram Showing the Relay Point, Client, and Server
Use the OSI Model to Guide Your Troubleshooting
Note that bridging cannot work unless the physical layer is working. The same is true for all layers above
the physical. Start with this layer first then work your way up through the other layers.
UDP Relay Configuration Problems
Incorrect Server IP Address
Specifying the incorrect IP address for the server is a simple and common mistake that causes UDP relay
to fail. The show ip helper CLI command lists the IP address (s) of all DHCP servers. This is the most
useful command to determine if the IP address for the server is correct.
The following is a sample of the show ip helper CLI command:
-> show ip helper
Ip helper :
Forward Delay(seconds) = 3,
Max number of hops
Forward option
= 4,
= standard
Forwarding Address :
10.10.10.58
Note that if the forward option is set to any thing other than standard, there will be restrictions as to which
UDP frames will be forwarded via the UDP relay function. the “DHCP Relay” chapter from the appropri-
ate OmniSwitch Network Configuration Guide.
page 5-2
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting BOOTP/DHCP/UDP Relay
Starting the Troubleshooting Procedure
Preliminary
6/5/06
Forward Delay Timer
Forward delay is the amount of time in seconds UDP relay will wait before forwarding a request to a
DHCP server, or the same DHCP server. (If only one is configured on the switch.) This allows the DHCP
server who initially got the DHCP request packet from the client to respond before the request is
forwarded to another DHCP server.
Additionally, the relay agent uses the forward delay value to determine if the client has waited long
enough before sending another DHCP request. The relay agent will discard the DHCP request packet sent
by the client if the delay variable in the DHCP request packet is less than the forward delay time.
Please note that the show ip helper CLI command is a universal command. It applies for all DHCP
server(s) configured on the switch.
Maximum number of hops
This value lists the maximum number of relays/hops a DHCP request packet will pass through before
being discarded. This prevents a DHCP request packet from looping through a network. A DHCP request
packet will be discarded if its hop count is greater than or equal to the maximum number of hops.
Displaying DHCP Statistics
The show ip helper stats CLI command lists the total number of DHCP packets sent by both the client
and the server. It also lists forward delay violations and violations for maximum hop count. This command
is especially useful to determine if the client is not incrementing its forward delay variable or if DHCP
request packets are looping through the network. And it also gives you a clear sense if the UDP Relay
agent is forwarding packets to or from either the client or the server. If there are incrementing Delay of
Hops Violations, this would explain why a pc is unable to get a DHCP address. A sniffer trace would be
useful in this instance.
The following is an example of the show ip helper stats CLI command:
-> show ip helper stats
Global Statistics :
Reception From Client :
Total Count =
Forw Delay Violation :
Total Count =
Max Hops Violation :
Total Count =
567, Delta =
18, Delta =
0, Delta =
66,
10,
0,
Server Specific Statistics :
Server 10.10.10.58
Tx Server :
Total Count =
31, Delta =
28
Note. See the “DHCP Relay Commands” chapter in the OmniSwitch CLI Reference Guide for more infor-
mation.
OmniSwitch Troubleshooting Guide September 2005
page 5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting the Troubleshooting Procedure
Troubleshooting BOOTP/DHCP/UDP Relay
UDP Relay and Group Mobility
If UDP Relay is being used with a Mobile DHCP Rule, determine if the end station is simply getting the
wrong IP address scope. If this is the case, verify group mobility, as the source VLAN of the UDP request
could be wrong when it reaches the UDP Relay function.
If no address is received and AVLAN forwarding is being used, again check group mobility and verify the
UDP request is being classified into the correct VLAN. This can be done by using the show mac-address-
table CLI command.
Take a trace both on the client connection as well as on the server connection can often be helpful to illu-
minate configuration errors.
page 5-4
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting BOOTP/DHCP/UDP Relay
Advanced Troubleshooting for UDP Relay
Preliminary
6/5/06
Advanced Troubleshooting for UDP Relay
To monitor the UDP traffic, the debug ip packet protocol udp CLI command can be used.
Note. See the “IP Commands” chapter in the OmniSwitch CLI Reference Guide for more information.
The output below shows the entire conversation of a DHCP client with MAC address 000039:73130 in
VLAN 20 to a DHCP server in VLAN 10 with a IP address of 10.10.10.58. (Note the sequence of
This output can be very verbose if done on a live switch and it can be useful to type in the stop command
prior to the start command and use the arrow up key to stop the debug display. (The stop command is the
debug ip packet protocol udp stop CLI command.
-> debug ip packet protocol udp start
C R 5/3 00003973130e->ffffffffffff IP 0.0.0.0->255.255.255.255 UDP 68,67
Discover with time=0
C R 5/3 00003973130e->ffffffffffff IP 0.0.0.0->255.255.255.255 UDP 68,67
Discover
C S 5/10 00d09579628b->00c04f046c2a IP 10.10.10.200->10.10.10.58 UDP 67,67
Relayed Discover
C R 5/10 00c04f046c2a->00d09579628b IP 10.10.10.58->20.20.20.200 UDP 67,67 Offer
C S 1/F 00d09579628d->ffffffffffff IP 10.10.10.58->255.255.255.255 UDP 67,68
Relayed Offer
C R 5/3 00003973130e->ffffffffffff IP 0.0.0.0->255.255.255.255 UDP 68,67 Request
C S 5/10 00d09579628b->00c04f046c2a IP 10.10.10.200->10.10.10.58 UDP 67,67
Relayed Request
C R 5/10 00c04f046c2a->00d09579628b IP 10.10.10.58->20.20.20.200 UDP 67,67
Acknowledge
C S 1/F 00d09579628d->ffffffffffff IP 10.10.10.58->255.255.255.255 UDP 67,68
Relayed Acknowledge
5 R CMM (00d09579628b)->(00c04f046c2a) IP 10.10.10.200->10.10.10.58 UDP 67,67
5 S 5/10 00d09579628b->00c04f046c2a IP 10.10.10.200->10.10.10.58 UDP 67,67
5 R CMM (00d09579628b)->(00c04f046c2a) IP 10.10.10.200->10.10.10.58 UDP 67,67
5 S 5/10 00d09579628b->00c04f046c2a IP 10.10.10.200->10.10.10.58 UDP 67,67
5 R 5/3 00003973130e->(ffffffffffff) ARP Request 20.20.20.1->20.20.20.1
OmniSwitch Troubleshooting Guide September 2005
page 5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell
Troubleshooting BOOTP/DHCP/UDP Relay
Dshell
To send the UDP Relay debug to the console, follow the following commands:
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
• Use the command udprelay_do_systrace = 0 to disable systrace and enable console output.
• Use the command C = x (where x=1 to 9.) This increases the levels of udprelay debug. A level of 5
will display the source, destination IP, and MAC lines seen below. A level of 8 will include the hex
dump of the packet. In addition, this level is very CPU intensive and will delay the UDP function. A
level of 9 displays all packets as well as IPC messages. At this time running a level of 9 uses up so
much of the UDP function that the relay agent can not pass traffic. A level of 9 is not recommended.
• And to turn it off use the udprelayDebugLevelCMM = -1 command.
The following is a sample UDP relay debug session:
enqueue_to_ip_using_ipc: Packet sent to IP using IPC
handle_event_udprelay_cmm(): Received on bsd socket
handle_event_bsd_udprelay_cmm: Recieved message from the bsd socket Received 284
bytes from bsd
socket 0x1a
We got in a tweaked zero IP address packet on bsd socket
Recvd on bsd socket pkt from 0.0.0.0, rtr-port addr=192.168.20.254, 0x-1062726402
Received short packet from bsd socket from 192.168.20.254, len=284 bytesReceived
request packet
for the bootp service on bsd socket BOOTP REQ: secs=0 hops=0x0
BOOTP REQ: Haven't waited long enough: secs=0 s/b >= 3
handle_event_udprelay_cmm(): received on ipc socket
handle_event_ipc_udprelay_cmm: num of bytes received = 352
handle_event_ni_udprelay_cmm: Recieved message from the NI
handle_event_ni_udprelay_cmm: Recieved message from the NI for regular UDP packet
hex_dump_udprelay_cmm: Printing the buffer at address = 0x60c3b10
00
03 00 01 01 5d 0e 70 50 -- 31 20 30 01 4a 00 00 00
14 60 14 41 00 ff ff ff -- ff ff ff 00 0b 85 03 07
f0 81 00 00 14 08 00 45 -- 00 01 38 4d cb 40 00 20
11 0b eb 00 00 00 00 ff -- ff ff ff 00 44 00 43 01
24 9e a6 01 01 06 00 73 -- 02 3f 32 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
0b 85 03 07 f0 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 00
page 5-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting BOOTP/DHCP/UDP Relay
Dshell
Preliminary
6/5/06
00 00 00 00 00 00 00 00 -- 00 00 00 00 00 00 00 63
82 53 63 35 01 03 32 04 -- c0 a8 14 9a 36 04 c0 a8
1e 05 39 02 02 4e 37 04 -- 01 1c 03 2b 3c 10 41 69
72 65 73 70 61 63 65 2e -- 41 50 31 32 30 30 ff
In the example above, the BOOTP request was dropped because the number of seconds elapsed since the
start of the process was not incremented (secs=0), and the forward delay was set to 3 seconds.
We got in a tweaked zero IP address packet on BSD socket shown below:
Recvd on bsd socket pkt from 0.0.0.0, rtr-port addr=20.20.20.200, 0x336860360
Received request packet for the bootp service on bsd socket BOOTP REQ: secs=0
hops=0x0
The BOOTP REQ field shows that we haven’t waited long enough. (The seconds shown is 0, when it
should be greater than or equal to 3.)
handle_uevent_udprelay_cmm(d): received on ipcp socket
relayDebug
handle_event_ipc_Ludprelay_cmm: num oef bytes received = v368elCMM =-1
handle_event_ni_udprelay_cmm: Recieved message from the NI
handle_event_ni_udprelay_cmm: Recieved message from the NI for regular UDP pack
Finally, the Dshell command bootpSizeCheck turns on/off the bootpSizeCheck function. (By default it is
off.) To turn it on enter the following:
Working: [Kernel]-> bootpSizeCheck = 1
To turn it on enter the following:
Working: [Kernel]-> bootpSixeCheck = 0
Note. OS-6600 supports minimum of 64 byte size packets.
OmniSwitch Troubleshooting Guide September 2005
page 5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell
Troubleshooting BOOTP/DHCP/UDP Relay
page 5-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Troubleshooting DNS
In order to troubleshoot a DNS problem, a basic understanding of the protocol/feature is required. Some
basic concepts are covered below. Reading the “Enabling the DNS Resolver” section in the “Logging Into
the Switch” chapter in the appropriate OmniSwitch Switch Management Guide is highly recommended.
In This Chapter
Introduction
The primary function of Domain Name Service or DNS enables the user to enter a pre-configured name
rather than an IP address to reach another host, via telnet, ftp, or ping. Once requested the switch contacts
a DNS server to find out what IP address is mapped to the name. If the server finds the entry a response is
sent to the switch indicating what IP address the name is associated with. The switch then attempts to
execute the command to the IP address. You can set up to 3 DNS servers from the CLI, WebView, or
through SNMP. If one server does not know the resolution the next server is queried to see if it knows the
resolution. You can also configure a domain name that the switch can belong to.
For example, say you want to set the domain name to “Alcatel.com” rather than entering
-> ping switch1.Alcatel.com
you could just enter
-> ping switch1
For all other domains you still need to enter the full syntax (ping switch2.xylan.com).
OmniSwitch Troubleshooting Guide September 2005
page 6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting a DNS Failure
Troubleshooting DNS
Troubleshooting a DNS Failure
Starting the Troubleshooting Procedure
If you try to use DNS resolution and it does not resolve, or connect from the switch with error such as
“unknown host” take the following steps.
Verify IP connectivity from the switch in question to the DNS server by pinging the server (destination) in
question from the switch (source) by its IP address. If successful, move on to layer 7 DNS or Name resolu-
tion issue. If ping fails, verify IP configuration. If ping is successful, verify that UDP port 53 is not being
filtered.
Layer 7 DNS or Name Resolution Issue
First verify that the switch is configured properly by using the show dns CLI command. Using this
command will show you the current settings and whether it is enabled and properly configured.
-> show dns
Resolver is : enabled
domainName : Alcatel.com
nameServer(s): 10.255.10.254
: 11.255.10.254
: 12.255.10.254
If there is more than one server on the network, make sure that the switch is pointing to the proper DNS
server(s).
If it is configured properly, then verify that you can still ping the server(s) by IP address; if successful ping
by name. If a ping by IP works but name doesn’t, verify the spelling of the name and that the proper
domain has been specified (labdevice.Alcatel.com).
If configuration appears ok to this point you may want to look at the DNS server to verify that the name
you are entering is configured in the server and is active, so that it will know how to respond properly. Can
another device use the DNS server to resolve the name in question? What about resolution of names in
other domains? If the server configuration appears ok, and other devices work with that server, then you
can take a trace (sniff) to see if the request is being sent to the server and what the server is responding
with.
A proper request and response will look similar to the following:
• In the request you should see a DLC header that has the Mac address of the switch as the source and
the MAC address of the DNS server as the destination.
• Next you will see the IP header, which should state that the protocol is UDP (17), the source IP address
should be the switch, and the destination IP address should be the DNS server.
• Next you have a UDP header that should have the DNS destination port of 53 (source port would vary).
The last portion is the DNS header, which should indicate the ID number (the response will have the
same number); it will show you the name the switch is asking to resolve to an IP address.
page 6-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DNS
DNS Configuration Considerations
• If you find conflicting information, then see which portion has the wrong information and focus on that
layer again (layer 2, 3, or 7).
• The response packet should contain the following fields: DLC with the source Mac address of the DNS
server, and the destination MAC address of the switch. The IP header will contain the source IP
address of the DNS server, and the destination IP address of the switch. The UDP header will contain
the source port 53 (the destination port varies). The DNS header will contain a response flag, and the
answer section will contain the name and the IP address that the name references.
DNS Configuration Considerations
CLI has a limitation when entering the domain name to 126 characters. If you enter the name from
WebView you can enter up to 255 characters, and it will show up properly from the CLI. There is a limit
of up to a maximum of 3 DNS servers.
OmniSwitch Troubleshooting Guide September 2005
page 6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
DNS Configuration Considerations
Troubleshooting DNS
page 6-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Troubleshooting Link
Aggregation
In order to troubleshoot a Link Aggregation issue a basic understanding of the protocol is required. Read-
ing the “Configuring Static Link Aggregation” and “Configuring Dynamic Link Aggregation” chapters in
the appropriate OmniSwitch Network Configuration Guide is also highly recommended.
The OmniSwitch supports two Link Aggregation Algorithms:
Two methods exist for configuring Link Aggregation:
• Static Link Aggregation Groups—Also referred to as OmniChannel used for Aggregation of Multi-
ple Link Segments between Alcatel Omniswitches.
• Dynamic Link Aggregation Groups—Also referred to as the IEEE 802.1ad standard used for Aggre-
gation of Multiple Link Segments between Alcatel Omniswitch and other Vendor.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Link Aggregation Limits and Guidelines
Troubleshooting Link Aggregation
Link Aggregation Limits and Guidelines
Consider the following when configuring Static Link Aggregation groups:
• Maximum number of link aggregation groups: 30 (OmniSwitch 6624/6648), 32 (OmniSwitch 7700/
7800), or 16 (OmniSwitch 8800).
• Number of links per group supported: 2, 4, 8, or 16
• Link aggregation groups are identified by unique MAC addresses, which are created by the switch.
• Load balancing is performed on ingress ports by the link aggregation groups to evenly balance traffic
flows on the physical links.
• The load is to be balanced between parallel links; because of this, Spanning Tree will be shut off on all,
but one link, which belongs to a channel. This port is referred to as the Primary port and the rest of the
ports are Secondary ports.
By default, first-generation Network Interface (NI) modules are not optimized for link aggregation. The
table below shows which NI modules are first-generation modules and are not optimized for link aggrega-
tion. ???? Where is this table, not provided in CS edits. ???? Use the show ni, show module, or show ni
commands to display the part number of the NI module. Second-generation NI modules are distinguished
from first-generation NI modules by "ENI2" or "GNI2" in the part number. (First-generation modules have
ENI, GNI, or 10GNI in their part numbers instead.) If the NI is a second-generation module you do not
need to optimize it.
To modify the optimization status of an NI module use the linkagg slot optimization command. To use
this command, enter linkagg slot followed by the slot number of the NI module then optimization and
either enable or disable. For example, to enable link aggregation optimization on an NI module is Slot 5
enter:
-> linkagg slot 5 optimization enable
When a port is a member of an aggregate group and optimization is enabled on this NI, all bridged traffic
sent from any other port (not part of the aggregate group) on the same switching ASIC to the aggregate
will be dropped. In this case, traffic needs to be routed between that port and the aggregate group. In a
chassis with both first-generation and second-generation NI modules you must configure static link aggre-
gation on all of the first-generation NI modules before you must configure static link aggregation on all of
these NI modules before you configure it on any of the second-generation NI modules. In addition, hot
insertion or hot swapping of a first-generation NI module into a chassis that has only second-generation NI
modules can cause configuration problems.
OmniSwitch 6624/6648 Restrictions
You can create up to 4 link aggregation (both dynamic and static) groups on a single OmniSwitch 6624
switch, up to 8 link aggregation groups on a single 6648 switch, and up to 30 link aggregation groups per
stack. In addition, ports must be configured sequentially and the first port configured must begin with port
number 1, 9, 17, or 25 on an OmniSwitch 6624 or 1, 9, 17, 25, 33, 41, 49, or 51 on an OmniSwitch 6648.
(In a stack, ports on different switches can be assigned to the same dynamic aggregate group.)
page 7-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Link Aggregation
Troubleshooting a Link Aggregation Failure
Troubleshooting a Link Aggregation Failure
Switch A
Switch B
OmniSwitch 7800
OmniSwitch 7800
Link Aggregation Setup
The figure above has the following setup:
• Switch A and Switch B connected back to back and Link Aggregation configured.
• Port 7/1 of Switch A is connected to port 7/1 of Switch B.
• Port 7/2 of Switch A is connected to port 7/2 of Switch B.
• VLAN 10 is assigned to this aggregate.
• PC1 connected to Switch A slot/port 1/5.
• PC2 connected to Switch B slot/port 1/5.
Verify the Configuration
First, verify that the ports and aggregates involved are assigned correctly. The CLI command show
linkagg will confirm that the aggregates are configured and are enabled and up as shown below:
-> show linkagg
Number Aggregate SNMP Id Size Admin State Oper State
Att/Sel Ports
-------+----------+---------+----+------------+--------------+-------------
2
3
Dynamic 40000002 8
Static 40000003 2
ENABLED
ENABLED
UP
UP
2 2
2 2
The show linkagg command followed by the aggregation number will show the aggregate state, size,
number of active ports, number of inactive ports, as well as the primary port. (See the sample below.) Note
also the primary port is the port that spanning tree runs on. It is important to verify that this port is not
changing regularly as that could cause spanning tree problems.
-> show linkagg 3
SNMP Id
Aggregate Number
: 40000003,
: 3,
SNMP Descriptor
Name
: Omnichannel Aggregate Number 3 ref 40000003 size 2,
: ,
Admin State
Operational State
Aggregate Size
: ENABLED,
: UP,
: 2,
Number of Selected Ports : 2,
Number of Reserved Ports : 2,
Number of Attached Ports : 2,
Primary Port
: 7/1
OmniSwitch Troubleshooting Guide September 2005
page 7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting a Link Aggregation Failure
Troubleshooting Link Aggregation
The show linkagg port CLI command followed by the slot and port number will display the port and link
state as well as if it is the primary port. (See the samples below.) If the operational or administrative state
is down and the port is primary, this indicates a software problem.
-> show linkagg port 7/1
Static Aggregable Port
SNMP Id
Slot/Port
: 7001,
: 7/1,
Administrative State
Operational State
Port State
: ENABLED,
: UP,
: ATTACHED,
: UP,
Link State
Selected Agg Number
: 3,
Port position in the aggregate: 0,
Primary port
: YES
-> show linkagg 2
Dynamic Aggregate
SNMP Id
: 40000002,
Aggregate Number
SNMP Descriptor
Name
: 2,
: Dynamic Aggregate Number 2 ref 40000002 size 8,
: ,
Admin State
Operational State
Aggregate Size
: ENABLED,
: UP,
: 8,
Number of Selected Ports : 2,
Number of Reserved Ports : 2,
Number of Attached Ports : 2,
Primary Port
LACP
: 8/1
MACAddress
: [00:d0:95:6b:54:0c],
Actor System Id
Actor System Priority
Actor Admin Key
Actor Oper Key
Partner System Id
: [00:00:00:00:00:00],
: 0,
: 0,
: 2,
: [00:00:00:00:00:00],
Partner System Priority : 0,
Partner Admin Key
Partner Oper Key
: 0,
: 2
Verify spanning tree on the virtual port that represents the link aggregate is in forwarding with the show
spantree command. Note the aggregate group will be displayed as 0/aggregate ID.
-> show spantree 10 ports
Spanning Tree Port Summary for Vlan 10
Adm Oper Man. Path Desig Fw Prim. Adm Op
Port Pri St St mode Cost Cost Role Tx Port Cnx Cnx Desig Bridge ID
-----+---+---+----+----+-----+-----+----+---+-----+---+---+---------------------
- 5/1
00:d0:95:79:62:8a
0/3 7 ENA FORW No
7 ENA FORW No
19
3 DESG 1 5/1 AUT PTP C350-
3
0 ROOT 1 0/3 AUT PTP 8000-00:d0:95:88:67:ca
If there are still connectivity problems across the aggregate link, make sure to check basic Ethernet
connectivity including spanning tree
page 7-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Link Aggregation
Troubleshooting a Link Aggregation Failure
Source Learning
When one of the primary links go down, the filtering database is purged and the process of learning the
source addresses is started again. The next available port is chosen to be the primary port. If the port that
goes down happens to be a secondary port, the MAC addresses learned on that particular port are re-
assigned to other ports evenly.
Link Aggregation Affecting Other Traffic
Note that depending on what software and hardware is being used, enabling link aggregation on a port
could affect other traffic on the same NI. Please call Customer Support if you suspect this to be the case.
Problems Creating a Group
Note that if there are problems creating a linkagg group or adding ports to an existing group the below
should be considered:
• Ports involved in a link aggregate need to all be of the same line speed.
• Mobile ports can not be a part of a link aggregate.
• There are a maximum of 32 aggregate groups allowed on an OmniSwitch 7700/7800/8800switch, 30
on a stack of OmniSwitch 6624/6648 switches, and 8 on a single OmniSwitch 6624/6648 switch. The
number goes down on OmniSwitch 7700/7800/8800 switches depending on the size of the aggregate,
see below.
Problems Deleting a Group
To delete a static link aggregate, the attached ports must first be deleted with the no static agg CLI
command. To delete a dynamic (802.3AD) aggregate, use the no lacp linkagg CLI command.
OmniSwitch Troubleshooting Guide September 2005
page 7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting a Link Aggregation Failure
Troubleshooting Link Aggregation
LACP 802.3AD
Most of the steps followed previously in this chapter apply to troubleshooting LACP. To verify the config-
uration use the show linkagg [agg. Number]. Again, verify the aggregate is enabled and up.
The most important aspect in troubleshooting LACP is to verify the transmission of valid LACPDUs. For
this you can go to the Dshell section as well as use a sniffer tool.
page 7-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Link Aggregation
Advanced Link Aggregation Troubleshooting
Advanced Link Aggregation Troubleshooting
To verify that the link aggregate software recognizes all the available slices, perform the following steps:
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
1 Use the lagg_Sock_cmm_boardupprint Dshell command, which displays all Network Interface (NI)
modes that are currently operating.
2 Verify that all NIs are present in the output.
-> dshell
Working: [Kernel]->lagg_Sock_cmm_boardupprint
LAGG boards up :
board in slot : 2 slice : 0 is up
board in slot : 5 slice : 0 is up
board in slot : 6 slice : 0 is up
board in slot : 7 slice : 0 is up
board in slot : 8 slice : 0 is up
value = 0 = 0x0
Working: [Kernel]->
To view the status of all ports and weather they are part of an aggregate use the la_pm_port_prt Dshell
command, which displays the the status of port mirroring and whether any ports are part of a link aggrega-
tion group. Note that status=2 indicates that port is part of an aggregate.
Working: [Kernel]->la_pm_port_prt
7/ 1 -> 0x0443e818 ifdx=7001 port_id=-1 assign=1 mirrored=0
admin_status=1 agg_status=2 bop_checked=1
7/ 2 -> 0x04442fa0 ifdx=7002 port_id=-1 assign=1 mirrored=0
admin_status=1 agg_status=2 bop_checked=1
8/ 1 -> 0x04442d30 ifdx=8001 port_id=-1 assign=1 mirrored=0
admin_status=1 agg_status=2 bop_checked=1
8/ 2 -> 0x04444090 ifdx=8002 port_id=-1 assign=1 mirrored=0
admin_status=1 agg_status=2 bop_checked=1
8/ 3 -> 0x04443ff0 ifdx=8003 port_id=-1 assign=1 mirrored=0
admin_status=1 agg_status=2 bop_checked=1
8/ 4 -> 0x044375c8 ifdx=8004 port_id=-1 assign=1 mirrored=0
admin_status=1 agg_status=2 bop_checked=1
8/ 5 -> 0x043d1348 ifdx=8005 port_id=-1 assign=1 mirrored=0
admin_status=1 agg_status=0 bop_checked=1
8/ 6 -> 0x043d1318 ifdx=8006 port_id=-1 assign=1 mirrored=0
admin_status=1 agg_status=0 bop_checked=1
To display an aggregate’s configuration use the command la_cmm_agg_prt Dshell command. This will
display the aggregate as well as the individual ports that are configured. Note the ifindex as it will be
needed.
-> dshell
Working: [Kernel]->la_cmm_agg_prt
2 -> 0x0443a958 ifindex=40000002 id=2 type=1 max_size=8 selected=2 reserved=2 a
ttached=2
OmniSwitch Troubleshooting Guide September 2005
page 7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Link Aggregation Troubleshooting
Troubleshooting Link Aggregation
MAC=00:d0:95:6b:54:0c name=
primary_port_index=0 admin_state=1 oper_state=2
Individual=0
Actor : ID=00:00:00:00:00:00 Prio=0 Admin Key=0 Oper Key=2
Partner : ID=00:00:00:00:00:00 Prio=0 Admin Key=0 Oper Key=2
0x04442ea8 status=6 ifindex=8001 port_id=224 port_type=1 port_index=0
adminstate=1 operstate=1 link_up_down=1
activation_order=1 bandwidth=100 agg_ctx_p=0x0443a958
agg_port_ctx_p=0x04442ea8 obj_port_ctx_p=0x04442d30
0x04442c20 status=6 ifindex=8002 port_id=225 port_type=1 port_index=1
adminstate=1 operstate=1 link_up_down=1
activation_order=2 bandwidth=100 agg_ctx_p=0x0443a958
agg_port_ctx_p=0x04442c20 obj_port_ctx_p=0x04444090
3 -> 0x0443c090 ifindex=40000003 id=3 type=0 max_size=2 selected=2 reserved=2 a
ttached=2
MAC=00:d0:95:87:a5:f2 name=
primary_port_index=0 admin_state=1 oper_state=2
0x04443288 status=6 ifindex=7001 port_id=204 port_type=0 port_index=0
adminstate=1 operstate=1 link_up_down=1
activation_order=1 bandwidth=1000 agg_ctx_p=0x0443c090
agg_port_ctx_p=0x04443288 obj_port_ctx_p=0x0443e818
0x0443e7d0 status=6 ifindex=7002 port_id=220 port_type=0 port_index=1
adminstate=1 operstate=1 link_up_down=1
activation_order=2 bandwidth=1000 agg_ctx_p=0x0443c090
agg_port_ctx_p=0x0443e7d0 obj_port_ctx_p=0x04442fa0
value = 84125696 = 0x503a800
To understand the output better, note that help is available in nidebug Dshell with the command
la_ni_info.
-> dshell
Working: [Kernel]->NiDebug
:0 nidbg> la_ni_info
7:0
7:0 LAGG values translation BOOL TRUE(1) FALSE(0)
7:0 NO CONFIG(0) CONF_NOT_SAVE(0x1) CONF_SAVED(0x2) CONF_CERTIFIED(0x4)
7:0 PORT_STATUS CREATED(1) CONFIGURABLE(2) CONFIGURED(3) SELECTED(4)
RESERVED(5) ATTACHED(6)
7:0 AGGREGABLE_STATUS NS(0) NOT_AGGREGABLE(1) AGGREGABLE(2)
7:0 TOKEN MSGTYPE NS(0) TRANSIT(1) TRANSIT_RSP_NOK(2) JOIN(3) DYN_DATA_REQ(4) D
YN_DATA_RSP_OK(5) DYN_DATA_RSP_NOK(6)
7:0 TOKEN STATE IDLE(0) UPDATE(1) PASSIVE(2) READY(3) REQUEST(4) GOT(5)
7:0 value = 0 = 0x0
To look at traffic statistics per aggregate use the command la_cmm_agg_stats_prt ifindex Dshell
command.
-> dshell
Working: [Kernel]->la_cmm_agg_stats_prt 40000003
Aggregate Statistics [40000003]
agg_nb_octets_rx_ok
= 0
agg_multicast_frm_rx_ok = 0
agg_broadcast_frm_rx_ok = 0
agg_unicast_frm_rx_ok
agg_frm_discard_rx
agg_frm_with_rx_errors
= 0
= 0
= 0
agg_unknown_protocol_frms = 0
agg_nb_octets_tx_ok = 0
page 7-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Link Aggregation
Advanced Link Aggregation Troubleshooting
agg_multicast_frm_tx_ok = 0
agg_broadcast_frm_tx_ok = 0
agg_unicast_frm_tx_ok
agg_frm_discard_tx
agg_frm_with_tx_errors
= 0
= 0
= 0
value = 40000003 = 0x2625a03
Since LACP is run on the NI it is important to verify the NI has the proper information. Many of the same
commands run above are available in the NI debugger. (See the table below.) The syntax and output are
the same.
la_ni_agg_prt
Displays aggregates.
Displays ports.
la_ni_port_prt
la_ni_port_up_prt
la_ni_lacp_port_stats_prt
la_ni_trace_prt
Displays ports up.
Displays LACP statistics.
Dumps link aggregation trace.
An event trace.
lagg_Sock_ni_traceprint
lagg_Sock_ni_boardupprint
Displays boards up.
To look at LACP statistics use the la_ni_lacp_port_stats_prt command. It monitors real time LACP-
DUs. It is important to verify that receive and transmit are incrementing on all active ports in a LACP
aggregate.
-> dshell
Working: [Kernel]->NiDebug
8:0 nidbg> la_ni_lacp_port_stats_prt
8:0
8:0 8:0: 0
8:0
8:0
lacpdus_rx
marker_pdus_rx
= 252289
= 0
8:0
marker_response_pdus_rx = 0
8:0
unknown_rx
= 0
8:0
illegal_rx
= 0
8:0
8:0
lacpdus_tx
marker_pdus_tx
= 252289
= 0
8:0
marker_response_pdus_tx = 0
8:0 8:0: 1
8:0
lacpdus_rx
= 252289
= 0
8:0
marker_pdus_rx
8:0
marker_response_pdus_rx = 0
8:0
unknown_rx
= 0
8:0
illegal_rx
= 0
8:0
8:0
lacpdus_tx
marker_pdus_tx
= 252289
= 0
8:0
marker_response_pdus_tx = 0
Note. LACPDUs are processed on the CMM.
If writing a PR for link aggregation it can be useful to attach the output of the Dshell command
la_cmm_trace_prt, which displays the actions/events the CMM handled.
OmniSwitch Troubleshooting Guide September 2005
page 7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
6800 Link Aggregation Debug Functions
Troubleshooting Link Aggregation
6800 Link Aggregation Debug Functions
The following functions are available for Link Aggregation debugging on the NI. A summary is shown
below.
Display Aggregates : la_ni_agg_prt
Display Ports
: la_ni_port_prt
Display Ports Up
: la_ni_port_up_prt
Display LACP stats : la_ni_lacp_port_stats_prt
Dump
LA Trace
: la_ni_trace_prt
Freeze LA Trace
Unfreeze LA Trace
: la_ni_trace_freeze
: la_ni_trace_unfreeze
Global variables : la_ni_display_add
Display Token : la_ni_token_prt
Display To unit tab : la_ni_tok_table_prt
values translation : la_ni_info
KITE debug
: la_ni_kite_help
Socket Handler debug : lagg_ni_Sock_help
la_ni_agg_prt
Certified: [Kernel]->la_ni_agg_prt
-> 0x0b8203c8 status=6 ifindex=1047 port_id=55 port_type=0 port_index=2adminstate=1
operstate=1 link_up_down=1 activation_order=3 multicast_state_origin=0x0
agg_ctx_p=0x0b8
la_ni_port_prt
Certified: [Kernel]->la_ni_port_prt
1:0: 0 -> 0x0ce87d28 status=0 ifdx=-1 id=0 type=0 agg_id=-1 port_index=-1
adminstate=1 operstate=2 link_up_down=1 activation_order=0 agg_ctx_p=0x0
1:0: 2 -> 0x0ce93e98 status=0 ifdx=-1 id=2 type=0 agg_id=-1 port_index=-1
adminstate=1 operstate=2 link_up_down=1 activation_order=0 agg_ctx_p=0x0
1:0: 4 -> 0x0ce92f90 status=0 ifdx=-1 id=4 type=0 agg_id=-1 port_index=-1
adminstate=1 operstate=2 link_up_down=1 activation_order=0 agg_ctx_p=0x0
1:0: 5 -> 0x0f75fe30 status=0 ifdx=-1 id=5 type=0 agg_id=-1 port_index=-1
adminstate=1 operstate=2 link_up_down=1 activation_order=0 agg_ctx_p=0x0
1:0: 6 -> 0x0ce736e0 status=0 ifdx=-1 id=6 type=0 agg_id=-1 port_index=-1
adminstate=1 operstate=2 link_up_down=1 activation_order=0 agg_ctx_p=0x0
1:0: 7 -> 0x0ce93050 status=0 ifdx=-1 id=7 type=0 agg_id=-1 port_index=-1
adminstate=1 operstate=2 link_up_down=1 activation_order=0 agg_ctx_p=0x0
1:0:48 -> 0x0ce92bd0 status=0 ifdx=-1 id=48 type=0 agg_id=-1 port_index=-1
adminstate=1 operstate=2 link_up_down=1 activation_order=0 agg_ctx_p=0x0
value = 87 = 0x57 = 'W'
page 7-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Link Aggregation
6800 Link Aggregation Debug Functions
la_ni_port_up_prt
Certified: [Kernel]->la_ni_port_up_prt
1:0: 0 -> 0x0ce87d28 status=0 port_id=0 adminstate=1 link_up_down=1
agg_ctx=0x00000000
1:0: 2 -> 0x0ce93e98 status=0 port_id=2 adminstate=1 link_up_down=1
agg_ctx=0x00000000
1:0: 4 -> 0x0ce92f90 status=0 port_id=4 adminstate=1 link_up_down=1
agg_ctx=0x00000000
1:0: 5 -> 0x0f75fe30 status=0 port_id=5 adminstate=1 link_up_down=1
agg_ctx=0x00000000
1:0: 6 -> 0x0ce736e0 status=0 port_id=6 adminstate=1 link_up_down=1
agg_ctx=0x00000000
1:0: 7 -> 0x0ce93050 status=0 port_id=7 adminstate=1 link_up_down=1
agg_ctx=0x00000000
1:0:48 -> 0x0ce92bd0 status=0 port_id=48 adminstate=1 link_up_down=1
agg_ctx=0x00000000
value = 91 = 0x5b = '['
la_ni_port_stats_prt
Certified: [Kernel]->la_ni_lacp_port_stats_prt
value = 1 = 0x1
la_ni_info
Certified: [Kernel]->la_ni_info
LAGG values translationBOOL TRUE(1) FALSE(0)
NO CONFIG(0) CONF_NOT_SAVE(0x1) CONF_SAVED(0x2) CONF_CERTIFIED(0x4)
PORT_STATUS CREATED(1) CONFIGURABLE(2) CONFIGURED(3) SELECTED(4) RESERVED(5)
ATTACHED(6)
AGGREGABLE_STATUS NS(0) NOT_AGGREGABLE(1) AGGREGABLE(2)
TOKEN MSGTYPE NS(0) TRANSIT(1) TRANSIT_RSP_NOK(2) JOIN(3) DYN_DATA_REQ(4)
DYN_DATA_RSP_OK(5) DYN_DATA_RSP_NOK(6)
TOKEN STATE IDLE(0) UPDATE(1) PASSIVE(2) READY(3) REQUEST(4) GOT(5)
value = 69 = 0x45 = 'E'
lagg_ni_Sock_help
Certified: [Kernel]->lagg_ni_Sock_help
NI
Slot : 1
Slice : 0
lagg_Sock_ni_globals
: Global variables
: warning trace
: time-out trace
: event trace [appid]
lagg_Sock_ni_warningprint
lagg_Sock_ni_totraceprint
lagg_Sock_ni_traceprint
lagg_Sock_ni_ttimetraceprint : treatment time trace
lagg_Sock_ni_intraceprint
lagg_Sock_ni_boardupprint
lagg_Sock_ni_printon
lagg_Sock_ni_printoff
lagg_Sock_ni_bufferprint
lagg_Sock_ni_Qtraceprint
lagg_Sock_dump_stats
: inter-NI trace
: boards up
: activates STP Socket Handler printf
: desactivates STP Socket Handler printf
: internal buffer statistics
: inQ trace [evtid]
: Event Tx stats
value = 49 = 0x31 = '1'
OmniSwitch Troubleshooting Guide September 2005
page 7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
6800 Link Aggregation Debug Functions
Troubleshooting Link Aggregation
la_ni_trace_freeze
Certified: [Kernel]->la_ni_trace_freeze
value = 244315184 = 0xe8ff430
la_ni_trace_unfreeze
Certified: [Kernel]->la_ni_trace_unfreeze
#_LA_SRV_TRACE_NI_LINKAGG_TRAC_UNFROZEN
value = 40 = 0x28 = '('
la_ni_kite_help
The la_ni_kite_help function may be accessed from the D-shell and will display the following output:
Working: [Kernel]->la_ni_kite_help
la_ni_kite_get_bcm_trunk_info(unit,agg_id) : display BCM info for given unit,agg
value = 83 = 0x53 = 'S'
page 7-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Troubleshooting 802.1Q
In order to troubleshoot an 802.1Q problem on a port, a basic understanding of the networking OSI model
is required to assist one with the troubleshooting steps to resolve a particular network problem.
Alcatel’s OmniSwitch supports 802.1Q specifications as defined by RFC 2674/IEEE 802.1Q/D11.
Reading the “Configuring 802.1Q” in the appropriate OmniSwitch Network Configuration Guide is also
highly recommended.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1Q
Troubleshooting 802.1Q
Troubleshooting 802.1Q
When troubleshooting an 802.1Q problem, it is important to not only investigate the 802.1Q feature and
configuration, but also the basic Ethernet connectivity between the problematic switches. Please refer to
Chapter 2, “Troubleshooting Switched Ethernet Connectivity,” of this document.
Switch A
Switch B
OmniSwitch 7800
OmniSwitch 7800
802.1Q Example
If there is no traffic passing at all across an 802.1Q link, verify basic Ethernet connectivity.
If there are particular VLANs that are not able to pass traffic, verify the configuration on both sides of the
link using the show vlan port CLI command. This will display the 802.1Q VLANs that are configured. It
will also display the default untagged VLAN. Confirm that these are configured correctly.
-> show vlan port 1/24
vlan
type
status
--------+---------+--------------
1
30
40
50
default forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
Verify the ports are in forwarding as expected. Note which bridge mode the switch is running in (1 per
VLAN or 1 per switch) If spanning tree appears to not be working correctly, please see Chapter 4, “Trou-
bleshooting Spanning Tree,” of this document.
Note that different spanning tree protocols can be used on the same tagged port.
To verify which VLAN a specific flow is being classified into, use the show mac-address-table command
shown below:
-> show mac-address-table 5/24
Legend: Mac Address: * = address not valid
Vlan
Mac Address
Type
Protocol
Operation
Interface
------+-------------------+--------------+-----------+------------+-----------
30 00:d0:95:88:67:ce
50 00:d0:95:88:67:d0
learned
learned
10806
10806
bridging
bridging
5/24
5/24
Total number of Valid MAC addresses above = 2
page 8-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1Q
Troubleshooting 802.1Q
Default VLAN Traffic
If traffic that should be in the default VLAN is not passing properly, first verify that the default VLAN is
set correctly, as see above. Also note the switch can be configured to either accept or deny untagged pack-
ets.
When enabling a port on the OmniSwitch 7700/7800/8800 to accept tagged traffic, you can specify
whether only 802.1Q tagged traffic is allowed on the port (deny all bridged traffic), or whether the port
accepts both tagged and untagged traffic.
OmniSwitch 7700/7800/8800 has a feature that enables it to accept all data on a bridged VLAN or deny all
of the bridged traffic.
The vlan 802.1q frame type all CLI command allows all the bridged traffic to be accepted on a tagged
link. When using an OmniSwitch 7700/7800/8800 with an OmniSwitch or Omni Switch/Router where
default VLAN needs to be bridged, this command should be set to all so that the bridged traffic can be
accepted by the OmniSwitch 7700/7800/8800 in addition to the tagged traffic.
For devices that cannot bridge on the tagged link, e.g. an OmniCore, the OmniSwitch 7700/7800/8800 can
be configured to accept only tagged traffic and ignore all the bridged traffic using the command. If frame
type is set to tagged, all non tagged traffic will be dropped.
The vlan 802.1q frame type tagged CLI command will deny all of the bridged traffic. Bridged traffic is
classified as traffic without a VLAN Identification (VID). Any packet without VID will be discarded.
Only tagged traffic will be accepted.
To verify if the port will receive untagged frames use the show 802.1q CLI command as shown below.
Note the Acceptable Frame Type field, Any Frame Type indicates this port will receive untagged
frames as well as tagged frames.
-> show 802.1q 5/24
Acceptable Frame Type
Force Tag Internal
:
:
Any Frame Type
on
Tagged VLANS
Internal Description
-------------+------------------------------------------+
30 TAG PORT 5/24 VLAN 30
40 TAG PORT 5/24 VLAN 40
50 TAG PORT 5/24 VLAN 50
Tagged Packet on an Untagged Port
If a tagged packet comes on an untagged or group mobility port (i.e., the vlan 802.1q CLI command has
not been used), then it can be classified in a VLAN other than the VLAN it currently belongs to. If this
classified VLAN (i.e., different then the packet tag) is now tagged on the egress side, then there are two
possible options.
One option is to carry the original tag of the packet and other option is to replace it with the classified
VLAN as the tag. If the force tag internal is disabled (on), then the tag is not replaced with the classified
VLAN. If the force tag internal is enabled (off), then the tag is replaced with the classified VLAN as the
tag.
Please note the above output of show 802.1Q CLI command shown in “Default VLAN Traffic” on
OmniSwitch Troubleshooting Guide September 2005
page 8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1Q
Troubleshooting 802.1Q
Question: What needs to be done if the native VLAN needs to be tagged when connected to an
OmniSwitch 7700/7800/8800?
Answer: The Gigabit/Ethernet port can be moved into a different dummy VLAN, and then the tagged
service can be created for the previous native VLAN. CLI Commands are as follows:
1 Dummy VLAN 99 created:
>vlan 99
2 A tag service is to be created on port 99 in VLAN 1.
->vlan 99 port default 1/1
3 Tag service created on VLAN 1.
->vlan 1 802.1q 1/1
4 (View the 802.1Q services created on port 1/1.
->show 802.1q 1/1
802.1Q with VLAN ID of 0
A VLAN ID of 0 means that Tag Header contains only user priority information; no VLAN identifier is
present in the frame. This frame will be claimed in the default VLAN for processing.
802.1Q and 64 Byte Packets
The Omni Switch 7700/7800/8800 was designed to send out tagged frames with a minimum size of 68
bytes. If the Omni Switch 7700/7800/8800 receives a tagged packet of 64 bytes it will be padded and sent
out 68 bytes (if untagged it will be 64 bytes).
page 8-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1Q
Advanced Troubleshooting
Advanced Troubleshooting
To verify the 802.1Q configuration from the CMM perspective use the debug 802.1q CLI command.
If frame type is set to all, then the egress default VLAN will equal the ports default VLAN. If force tag
internal is set to off, e.g. force tag internal will equal 0, otherwise it will be ffffffff.
The following shows the debug 802.1q CLI command used to verify that the slot and port are up.
-> debug 802.1q 5/24
Slot Status =
Port Status =
slot up
port up
GENERAL INFO ESM: USER PORT 1-12 = CORONADO PORT 0-11
GENERAL INFO ESM: USER PORT 13-24 = CORONADO PORT 16-27
GENERAL INFO GSM-2: USER PORT 1 = CORONADO PORT 12
GENERAL INFO GSM-2: USER PORT 2 = CORONADO PORT 28
GENERAL INFO GSM-8: USER PORT 1 = CORONADO PORT 0
GENERAL INFO GSM-8: USER PORT 2 = CORONADO PORT 16
GENERAL INFO GSM-8: USER PORT 3 = CORONADO PORT 1
GENERAL INFO GSM-8: USER PORT 4 = CORONADO PORT 17
GENERAL INFO GSM-8: USER PORT 5 = CORONADO PORT 2
GENERAL INFO GSM-8: USER PORT 6 = CORONADO PORT 18
GENERAL INFO GSM-8: USER PORT 7 = CORONADO PORT 3
GENERAL INFO GSM-8: USER PORT 8 = CORONADO PORT 19
HARDWARE INFO for slot = 5 and port = 24:
At reg_addr = 660012c, Ingress tag-untag:= 8000000:
At reg_addr = 6a00010, Eg tag-untag: = 8000000:
At reg_addr = 660106c,for protocol = 0,ing default vlan: = a
At reg_addr = 66010ec,for protocol = 1,ing default vlan: = a
At reg_addr = 660116c,for protocol = 2,ing default vlan: = a
At reg_addr = 66011ec,for protocol = 3,ing default vlan: = a
At reg_addr = 660126c,for protocol = 4,ing default vlan: = a
At reg_addr = 66012ec,for protocol = 5,ing default vlan: = a
At reg_addr = 660136c,for protocol = 6,ing default vlan: = a
At reg_addr = 66013ec,for protocol = 7,ing default vlan: = a
At reg_addr = 660146c,for protocol = 8,ing default vlan: = a
At reg_addr = 66014ec,for protocol = 9,ing default vlan: = a
At reg_addr = 660156c,for protocol = a,ing default vlan: = a
At reg_addr = 66015ec,for protocol = b,ing default vlan: = a
At reg_addr = 660166c,for protocol = c,ing default vlan: = a
At reg_addr = 66016ec,for protocol = d,ing default vlan: = a
At reg_addr = 660176c,for protocol = e,ing default vlan: = a
At reg_addr = 66017ec,for protocol = f,ing default vlan: = a
At reg_addr = 6a7006c, egress default vlan: = a
At reg_addr = 6600118, protocol cam on/off: = 0 :
At reg_addr = 660011c, trusted/untrusted: = 0
At reg_addr = 6600130, secure/unsecure: = 0
At reg_addr = 6608078, for vlan = 1e,spanning tree vector: = 8000000
At reg_addr = 66080a0, for vlan = 28,spanning tree vector: = 8000000
At reg_addr = 66080c8, for vlan = 32,spanning tree vector: = 8000000
At reg_addr = 6a00014, Eg force tag internal: = ffffffff:
OmniSwitch Troubleshooting Guide September 2005
page 8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Troubleshooting
Troubleshooting 802.1Q
output definitions
Aggregate/Slot Status
Port Status
Whether the slot or aggregate link is actively running.
Whether the port is actively running.
General Info
Provides general information on the modules in the chassis, including
module type, number of ports, and ASIC.
Hardware Info
Lists the various debug messages for the selected slot and port.
page 8-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1Q
Dshell Commands
Dshell Commands
The first step in troubleshooting for an 802.1Q problem through Dshell is to verify the configurations.
Validating the configurations in Dshell remove the chances of inconsistency between the CLI and Dshell.
Following is the list of commands to verify the configuration of the 802.1Q ports in Dshell. These
commands will verify that there is no inconsistency between the CLI and Dshell.
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
The Dshell command print_default_vlan_8021q_cmm shows the default or native VLAN for all of the
802.1Q ports. Slot and port are zero based.
-> dshell
Working: [Kernel]->print_default_vlan_8021q_cmm 4,23
For slot = 4 and port = 23, default_vlan = 10value = 4 = 0x4
Working: [Kernel]->print_port_aggregation_status_8021q_cmm 6,0
print_port_aggregation_status_8021q_cmm: Slot number = 6, Port number = 0, por
t_aggregation_status = AGGREGABLE PORT
value = 6 = 0x6
Working: [Kernel]->print_configured_list_aggregate_8021q_cmm 6,0
print_configured_list_8021q_cmm: aggregate_id = 6, number_of_configured_vlans =
0, vlan list =
value = 0 = 0x0
Note. Use the Dshell NIDebuger to run the following command.
To see the 802.1Q VLANs for a particular port use the print_configured_list_8021q_ni zero_based_port
command as shown below: ???? This command was not marked for deletion but the example below was.
Is this correct and/or is there a new example if this command should stay? ????
-> dshell
Working: [Kernel]->NiDebug
5:0 nidbg> print_configured_list_8021q_ni 23
5:0
5:0 print_configured_list_8021q_ni: Port number = 23, number_of_configured_vlan
s = 3, vlan list = 30,40,50,
5:0 value = 23 = 0x17
5:0 nidbg> print_acceptable_frame_type_8021q_ni 23
5:0
5:0 print_acceptable_frame_type_8021q_ni: Port number = 23, acceptable_frame_t
ype = ANY FRAME TYPE
5:0 value = 23 = 0x17
5:0 nidbg> print_force_tag_internal_8021q_ni 23
5:0
5:0 print_force_tag_internal_8021q_ni: Port number = 23, force_tag_internal =
OmniSwitch Troubleshooting Guide September 2005
page 8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Commands
Troubleshooting 802.1Q
ON
5:0 value = 23 = 0x17
5:0 nidbg> print_default_vlan_8021q_ni 23
5:0
5:0 print_default_vlan_8021q_ni: For port = 23, default vlan = 10 value = 23 =
0x17
5:0 nidbg> print_configured_list_aggregate_8021q_ni 2
5:0
5:0 print_configured_list_8021q_ni: Aggregate number = 2, number_of_configured_
vlans = 3, vlan list = 30,40,50,
5:0 value = 2 = 0x2
5:0 nidbg> print_port_aggregation_status_8021q_ni 2
5:0
5:0 print_port_aggregation_status_8021q_ni: Port number = 2, port_aggregation_
status = NOT AGGREGABLE PORT
5:0 value = 2 = 0x2
5:0 nidbg> print_port_list_in_aggregate_8021q_ni 3
5:0
5:0 print_port_list_in_aggregate_8021q_ni: aggregate_id = 3, number_of_ports =
0, port_list =
5:0 value = 3 = 0x3
5:0 nidbg> print_default_vlan_aggregate_8021q_ni 2
5:0
5:0 print_default_vlan_aggregate_8021q_ni: For aggregate = 2, default vlan = 1
value = 2 = 0x2
page 8-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Troubleshooting Group
Mobility
In order to troubleshoot a VLAN Mobility problem, a basic understanding of the technology is required.
Reviewing the “Assigning Ports to VLANs” and “Defining VLAN Rules” chapters in the appropriate
OmniSwitch Network Configuration Guide is highly recommended.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting a VLAN Mobility Failure
Troubleshooting Group Mobility
Troubleshooting a VLAN Mobility Failure
There is no systematic procedure to troubleshoot a VLAN mobility issue. This section will give you a
checklist, with a generally best course of action to take to determine the source of the VLAN mobility fail-
ure.
1 Verify that port mobility has been turned on for a given port and is still active.
2 Determine VLAN rules.
3 Determine mobile port membership.
4 Verify Traffic on a mobile port.
5 Correct rules, or move devices appropriately.
In general, the above steps are a good guideline for determining what is causing mobile port(s) to join
incorrect VLAN(s) or to not join any VLAN(s). Most likely, all troubleshooting steps will not be needed.
After each step in the troubleshooting process, determine if a configuration modification is necessary, and
make any needed corrections.
Note that mobility is different in AOS products when compared to legacy XOS products. The newer AOS
products implement mobility on the port level. There is no longer the concept of having a “mobile group”
as there was in the legacy XOS.
For dynamic assignment of a port to a VLAN, port mobility must be enabled on a given port. To deter-
mine if port mobility is enabled for given port, issue the show vlan port mobile CLI command, or for a
specific port, use the show vlan port mobile CLI command with the slot/port option. If port mobility has
not been enabled, use the show vlan port mobile CLI command to enable it. All variables in this output
are important to understand if there are problems with group mobility. (See below for an example of this
command.)
• Verify the feature is enabled ON for this port. The default is OFF.
• If mobile is on and the feature appears to still not be working, understand that if ignore BPDU is off,
and the port is an interswitch connection, the arrival of a BPDU will turn mobility off on the port.
• If traffic is not passing on the default vlan, verify that it is configured to the correct vlan and that
Default Vlan is enabled. If it is not enable, only traffic matching a specific rule will pass.
• If there is a device such as a printer, that only sources traffic when it boots, it may be advantageous to
turn off default VLAN restore.
Note. OS-6600 supports only one rule per port. One port can only become a member of one rule unlike
OS-7700/7800/8800, which support multiple rules per port. Hubs are also not supported on a mobile port.
-> show vlan port mobile 6/1-3
Mobility
: on,
Config Default Vlan: 1,
Default Vlan Enabled: on,
Default Vlan Restore: on,
Authentication
Ignore BPDUs
: off,
: off
page 9-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Group Mobility
Troubleshooting a VLAN Mobility Failure
With VLAN mobility, it is critical that the network administrator have a good understanding of the traffic
on their network in order to assign proper rules. It is not only important to verify the required rules have
been configured, but it is also important to understand the concept of precedence for rules that may over-
lap. In addition, it is important not to design beyond the limitations of the software. This can be verified by
referencing the latest release notes for the current software revision.
To verify the rules that have been configured, use the show vlan rules CLI command as shown below:
-> show vlan rules
11.2.1.1.1.1.1 Legend: type: * = binding rule
type
vlan
rule
-----------------+------+-------------------------------------------------------
ip-net
protocol
255
355
21.0.0.0, 255.0.0.0
ipx-e
mac-ip-port*
dhcp-mac-range
1500
255
00:da:95:00:ce:3f, 21.0.0.43, 3/10
00:da:95:00:59:10, 00:da:95:00:59:9f
To determine if a port has seen traffic that has matched a configured rule, use the show vlan port [slot/
port] CLI command with the slot/port option shown below:
-> show vlan port 6/1
vlan
type
status
--------+---------+--------------
1
255
default forwarding
mobile forwarding
If the desired group is not present, and there are no other mobile groups present for the switch, verify the
port is set to mobile and that a BPDU has not turned off mobility.
If there are other groups learned on the port, but one is missing verify both the rule configuration as well
as the traffic on the ingress of that port. Note rule precedence if there is a possibility for overlapping rules.
A sniffer may be useful to verify the traffic coming into the port is what is expected.
Binding Rules
Note that for a frame to be classified into a vlan with binding rules, the frame must match ALL binding
rules, for it to be classified into that particular vlan. If it does not match all binding rules, the frame will
either be classified as default, or another vlan should it match other rules configured on the switch
Port Rules
Port rules only apply to outgoing mobile port traffic and do not classify incoming traffic. If a mobile port
is specified in a port rule, its incoming traffic is still classified for VLAN assignment in the same manner
as all other mobile port traffic.
OmniSwitch Troubleshooting Guide September 2005
page 9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting a VLAN Mobility Failure
Troubleshooting Group Mobility
Precedence
Due to the variety of rules that can be configured there can be traffic that can match multiple rules, i.e. an
IP frame could match a network address rule as well as a protocol rule. For this reason, all rules are
arranged in a precedence. When a frame is received on a mobile port, switch software starts with rule one
in the rule precedence table and progresses down the list until there is a successful match between rule
criteria and frame contents. The higher the rule is in the list, the higher its level of precedence. To verify
which VLAN a frame is being classified into use the show mac-address-table CLI for the MAC address
in question as shown below:
-> show mac-address-table 00:b0:d0:75:f1:97
Legend: Mac Address: * = address not valid
Vlan
------+-------------------+--------------+-----------+------------+-----------
255 00:b0:d0:75:f1:97 learned 10800 bridging 6/1
Total number of Valid MAC addresses above = 1
Mac Address
Type
Protocol
Operation
Interface
Please see the “Defining VLAN Rules” chapter in the appropriate OmniSwitch Network Configuration
Guide for a detailed list of all rules and their relative precedence. has important information about VLAN
Rule precedence.
page 9-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Group Mobility
Advanced Troubleshooting
Advanced Troubleshooting
To verify if a port is a candidate for mobility as well as if mobility as been turned on for a given port use
the debug vlan rule ports CLI command. Note that ports 6/1-2 are mobile ports. Ports 7/1-2 and 8/1-2 are
not a candidate for mobility because they are either 802.1Q ports or part of a link aggregate.
-> debug vlan rule ports
port candidate mobile
------+-----------+---------
2/1
2/2
6/1
6/2
7/1
7/2
8/1
8/2
+
+
+
+
-
-
-
-
-
-
+
+
-
-
-
-
To look at the protocol indicator map use the debug vlan rule protocol-map CLI command as shown
below. This command displays the Protocol Indicator (PI) map. In order for group mobility to classify
packets on the OmniSwitch, it needs to program the hardware with protocol type and protocol indicator.
The Protocol Indicator is later used in the CAM lookup. This command displays the protocols
programmed and the Protocol Indicator.
-> debug vlan rule protocol-map
*** Protocol Indicator Map ***
proto = Ethernet II IP
proto = Ethernet II ARP
proto = Ethernet II RARP
Frame = E-II PI = 0
Frame = E-II PI = 0
Frame = E-II PI = 0
proto = SNAP IP
proto = SNAP ARP
proto = SNAP RARP
Frame = 802.3PI = 1
Frame = 802.3 PI = 1
Frame = 802.3 PI = 1
proto = IPX Ethernet II
proto = IPX Novell
Frame = E-II PI = 4
Frame = 802.3 PI = 3
proto = IPX LLC
proto = IPX SNAP
Frame = 802.3 PI = 2
Frame = 802.3 PI = 5
Note. OmniSwitch 6624/6648 switches do not have the protocol CAM. Instead, database shown above is
maintained in software.
The debug vlan rule memory command displays the memory allocated for the group mobility rules, as
shown below:
-> debug vlan rule memory
*** RULE MEM BLOCKS ***
1. 4443338 1
The debug vlan rule database command displays the group mobility rules database, as shown below:
-> debug vlan rule database
IP NETWORK RULES
B ssz=2 p=56644e0 l=56644e0 r=4443364 v=60
R ssz=1 p=4443340 l=56644e0 r=56644e0 v=90
PROTOCOL RULES
B ssz=1 p=56644e0 l=56644e0 r=56644e0 v=70
OmniSwitch Troubleshooting Guide September 2005
page 9-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell
Troubleshooting Group Mobility
Dshell
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
NI Debug Dshell
Use the gmnSetPrintDestination command from the NiDebug Dshell command to redirect the output of
the group mobility commands to the current session.
-> dshell
Working: [dshell]->NiDebug
6:0 nidbg> gmnSetPrintDestination
6:0
value = 0 = 0x0
All NIs should have a copy of all rules configured on the switch, regardless if that NI has used the rule yet.
To verify that the rules have been loaded on the NI use the gmnShowRules command from the NiDebug
Dshell command. Use the same rule index from above, i.e. 0 = IP net address rule.
-> dshell
Working: [dshell]->NiDebug
6:0 nidbg> gmnShowRules 0
6:0
6:0 NI IP Network Address Rules (2 rules)
6:0 ---------------------------
6:0 net = 5a5a5a00 mask = ffffff00 vid = 90
6:0 net = 3c3c3c00 mask = ffffff00 vid = 60
6:0 value = 0 = 0x0
To verify that the NI sees a port as mobile use the gmnIsPortMobile (port number (zero based))
command from the NiDebug Dshell command. (Please note that 1= mobile and 0=non-mobile.)
-> dshell
Working: [dshell]->NiDebug
6:0 nidbg> gmnIsPortMobile 1
6:0
value = 1 = 0x1
This gmnClassifyDebug command displays group mobility classification process on the NI as the pack-
ets are received. This has to be issued in conjunction with the gmnPrintDestination command to see the
output on the console. This command is issued on the NiDebug prompt for the NI we want to debug.
-> dshell
Working: [dshell]->gmnPrintDestination = 0
Working: [dshell]->gmnClassifyDebug = 1
page 9-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Group Mobility
6800 Group Mobility Troubleshooting
6800 Group Mobility Troubleshooting
The following commands and debugging functions are available for troubleshooting Group Mobility on
the NI. A summary is shown below.
• gmHelp
show vlan rules
SW_2T19-> show vlan rules
Legend: type: * = binding rule
type
vlan
rule
-----------------+------+-------------------------------------------------------
ip-net
ip-net
ip-net
dhcp-port
dhcp-port
dhcp-port
dhcp-port
9
104
112
104
104
104
104
166.24.9.0, 255.255.255.0
166.24.104.0, 255.255.248.0
166.24.112.0, 255.255.248.0
1/1
1/2
1/3
1/4
gmHelp
Working: [Kernel]->gmHelp
***************************************************
Group Mobility Help for CMM
***************************************************
'gmcKiteDebug = 1' must be done in order to see the outputs on below debug
commands.
It also enables the real time debugger. To disable 'gmcKiteDebug = 0'.
gmcShowPorts ---------------Displays all the ports in the system
gmcShowMipTables -----------Displays all MIP tables used
gmcShowRules (GmcRuleType) -Displays all rules of specified type
gmcShowPiMap ---------------Displays Protocol Indicator Map
gmcShowConnections ---------Displays connections with all CMM interfaces
gmcShowNiConnections -------Displays connections with all NI interfaces
gmcMacVlanShowBuffer (int type) - If type=0, display macvlan_sw malloc counter only
- If type=1, display above and macvlan_sw table
gmcDebugKiteShowCML (int slot) -- Display CML setting at CMM
OmniSwitch Troubleshooting Guide September 2005
page 9-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6800 Group Mobility Troubleshooting
Troubleshooting Group Mobility
***************************************************
Group Mobility Help for NI
***************************************************
gmnKiteDebug = 1 ------- Enable real time debugging
gmnKiteDebug = 0 ------- Disable real time debugging
gmnKiteShowEframe = 1 -- Display E_FRAME_PARAM when gmnKiteDebug is enabled
gmnKiteShowEframe = 0 -- Do not display E_FRAME_PARAM when gmnKiteDebug is enabled
gmnKiteShowDefVlan -------- Display def vlan stored at gmn
gmnKiteShowPiMap -------- Display protoCam0 and protoCam1
gmnKiteDebugPI
setting
-------- Display the proto and port-proto rule's PI map
gmnKiteShowPortSet -------- Display port configuration stored at gmn
gmn_bcm_port_ifilter_get -- Read ingress filtering setting from HW
gmn_bcm_port_learn_get ---- Read CML setting from HW
gmn_bcm_port_discard_get -- Read whether the port is tagged or untagged port
from HW
gmn_bcm_vlan_port_get (int vid) -- Read VPM for the vlan from HW
gmnKiteShowRules ----------------- Display Mobile rule table at gmn
gmnMacVlanShowBuffer (int type) -- If type=0, display macvlan_sw malloc counter
only
-- If type=1, display above and macvlan_sw table
gmcKiteDebug
Certified: [Kernel]-> gmcKiteDebug = 1
gmcShowPorts
Certified: [Kernel]->gmcShowPorts
GMC_LOG: "gmcShowPorts", gmc: 1/1 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/2 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/3 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/4 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/5 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/6 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/7 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/8 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/9 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/10 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/11 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/12 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/13 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/14 pot=1 mob=1
GMC_LOG: "gmcShowPorts", gmc: 1/15 pot=1 mob=1
gmcShowRules
Certified: [Kernel]->gmcShowRules
GMC_LOG: "gmcShowRule", ht=1 bht=0 col=R GMC_LOG: "gmcShowRule", GMC_LOG: "gmcSh
owRule", vid =
9
GMC_LOG: "gmcShowRule", ht=2 bht=1 col=B GMC_LOG: "gmcShowRule", GMC_LOG: "gmcSh
owRule", vid = 104
page 9-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Group Mobility
6800 Group Mobility Troubleshooting
GMC_LOG: "gmcShowRule", ht=1 bht=0 col=R GMC_LOG: "gmcShowRule", GMC_LOG: "gmcSh
owRule", vid = 112
value = 12 = 0xc
gmnKiteDebug
Certified: [Kernel]->gmnKiteDebug = 1
Certified: [Kernel]->gmnKiteShowPortSet
port mobile enabled restore ignoreBPDU auth ifilter
----+------+-------+-------+----------+----+-------
0
1
2
3
4
5
6
7
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
gmnKiteShowRules
Certified: [Kernel]->gmnKiteShowRules
IP Network Address Rules
---------------------------
net = a6186800 mask = fffff800 vid = 104
net = a6180900 mask = ffffff00 vid = 9
net = a6187000 mask = fffff800 vid = 112
DHCP Port Rules
---------------------------
port = 74 vid = 104
port = 39 vid = 104
port = 98 vid = 104
port = 16 vid = 104
gmnMacVlanShowBuffer
Certified: [Kernel]->gmnMacVlanShowBuffer
gmnKiteMacVlan_bufferCount = 0
gmnKiteMallocCount
gmnKiteFreeCount
value = 31 = 0x1f
= 0
= 0
OmniSwitch Troubleshooting Guide September 2005
page 9-9
Download from Www.Somanuals.com. All Manuals Search And Download.
6800 Group Mobility Troubleshooting
Troubleshooting Group Mobility
page 9-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Troubleshooting QoS
In order to troubleshoot Quality of Service (QoS), a basic understanding of the concept is required. Some
basic concepts are covered below.
Reading the “Configuring QoS” and “Configuring ACLs” chapters in the appropriate OmniSwitch
Network Configuration Guide is also highly recommended.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 10-1
Download from Www.Somanuals.com. All Manuals Search And Download.
QoS Behavior
Troubleshooting QoS
QoS Behavior
It is important to know how QoS behaves by default in order to understand the way it works and to be able
to troubleshoot it. So first of all, a list of default behaviors.
Default
By default, flows that do not match any policies are accepted on the switch. This applies to bridged,
routed, and multicast flows.
Use the following command to change the defaults:
• qos default routed disposition deny
• qos default bridged disposition deny
• qos default multicast disposition deny
When QoS is enabled, make sure that you create policy rules on the switch to allow traffic when you
change the global disposition to deny; otherwise no traffic will go through.
When QoS is enabled and policy rules have been defined, if there is more than one policy that matches the
flow, the switch uses the policy with the highest precedence.
To view the current global configuration for QoS, use the show qos config CLI command.
Be aware of the following limitations:
• Maximum number of policy rules 2048.
• Maximum number of policy conditions 2048.
• Maximum number of policy actions 2048.
QoS Queues and Ports
There are 2048 queues per NI and by default 4 default queues per port on OmniSwitch 7700/7800/8800
switches. Default queues are created for each port on the switch at start up. The switch creates additional
queues based on policy rules that match incoming flows.
On the OmniSwitch 6624/6648, 4 default queues are created for each port at startup. Additional queues are
not created.
When a flow matches a policy, it is placed in a QoS queue. If the disposition is accept and no other action
parameters are configured, the flow is placed in a default queue.
By default, QoS is enabled on all ports. If QoS is disabled on a port, only default queues will be created on
the disabled port. However, ACL and NAT will continue to be enforced on that port.
Note. In Release 5.1.5 and later, QoS can no longer be disabled on a port.
page 10-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
On the OmniSwitch 6624/6648, flows always share queues. On the OmniSwitch 7700/7800/8800, flows
may share queues if they match the same policy and the policy action is configured for sharing through the
policy action CLI command. In order to be shared, the flows must arrive on the same slice and be destined
for the same egress port.
The default maximum reserve bandwidth is the physical bandwidth allowed by the port (use the CLI
command qos port slot/port maximum default bandwidth to alter it).
By default switch ports are not trusted; that is, they do not recognize 802.1p or ToS/DSCP settings in
packets of incoming traffic. By default, the port defaults for 802.1p and ToS/DSCP are 0.
Troubleshooting QoS
Information Gathering on Symptoms and Recent Changes
The first step in any troubleshooting process is to gather information. The more information you have
about the symptoms and characteristics of a problem—including when it first occurred—the better your
chances are of solving the problem quickly and efficiently.
Starting the Troubleshooting Procedure
There is no systematic procedure to troubleshoot a QoS issue. This section will give you a checklist, reca-
pitulating some of the actions available to you to troubleshoot QoS issues.
QoS Activation
By default the QoS Manager is enabled on the switch. If QoS is disabled, policies will not work. To check
whether or not QoS is enabled, use the show qos config command. To enable QoS if it is disabled, use the
following command:
-> qos enable
Note. Use the qos enable CLI command to activate QoS globally.
When QoS is disabled globally, any flows coming into the switch are not matched to policies. Note that
individual policy rules may be enabled or disabled with the policy rule command. The global setting over-
rides the setting for individual rules.
OmniSwitch Troubleshooting Guide September 2005
page 10-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
QoS Apply
Another common mistake for having a policy not work is to forget to apply the QoS configuration to the
configuration. Most QoS commands require a qos apply CLI command before the configuration is active.
This is valid for QoS configuration on the CLI. Loading a QoS ASCII configuration file does not require a
qos apply command.
Note. Use the qos apply CLI command to activate your QoS settings. (You still need to save on exit.)
Rebooting without applying the changes will cause the settings to return to their last applied values.
Invalid Policies
Valid condition/action combinations are listed in the user manual. The CLI prevents you from configuring
invalid condition combinations that are never allowed.
Use the Policy Condition/Action Combinations table in the user documentation as a guide when creating
policy rules.
Two important limitations to remember:
• Layer 2 and Layer 3/4 conditions should not be combined.
• Layer 2 conditions cannot combine source and destination parameters.
• On the OmniSwitch 6624/6648, source and destination parameters may not be combined in the same
condition.
Rules Order
The order of entry when defining rules use policy rule command with the precedence option. The Range
for precedence is 0-65535. The rule with the highest precedence will be applied.
When a flow comes into the switch, the Layer 2 source rules are examined first for a match. If no match is
found, the Layer 2 destination rules are examined. If no match is found, the Layer 3 rules are examined. If
a flow matches more than one rule in a particular precedence list (for example, the Layer 2 source list), the
precedence determines which rule the switch will apply to the flow.
More than one rule may have the same condition, but the rule with the highest precedence will be applied
to the flow matching the condition. If a policy is configured with the same precedence value as another
policy, the policy that was created first has the higher precedence. The new policy is considered lower
priority.
For the following rules, if condition “oktftp” and “noip” are satisfied, the rule “oktftp” would take prece-
dence over rule “nopip” because it has a higher precedence number. See the examples below:
-> policy rule oktftp precedence 200 condition oktftp action oktftp
-> policy rule noip precedence 100 condition noip action noip
page 10-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
Viewing QoS Settings
When troubleshooting, it is essential to keep track of all your QoS settings that are effective; i.e. that have
been applied. A good way to display all the QoS settings is to use the show configuration snapshot qos
CLI command, which generates a snapshot file of the switch’s QoS current running configuration. See the
following example below:
-> show configuration snapshot qos
! QOS :
qos disable stats interval 30 log level 7 log console
policy condition noip source ip 192.168.10.0 mask 255.255.255.0
policy condition oktftp source ip 192.168.10.0 mask 255.255.255.0 ip protocol 17
destination ip port 69
policy action noip disposition deny
policy action oktftp
policy rule oktftp precedence 200 condition oktftp action oktftp
policy rule noip precedence 100 condition noip action noip
qos apply
Viewing QoS Policy Rules
To display all your pending and applied policy, use the show policy rule CLI command to display infor-
mation about all pending and applied policy rules or a particular policy rule. For example:
-> show policy rule
Policy
+BLOCK_20
Cnd/Act:
From Prec Enab Inact Refl Log Save
cli 0 Yes No No No Yes
BLOCK_20 -> BLOCK_20
The above display indicates that rule BLOCK_20 is active and is used to classify traffic on the switch (the
Inact field displays No). The rule BLOCK_20 has been configured since the last qos apply command
was entered, as indicated by the plus (+) sign. If the rule has been created recently, it will not be used to
classify traffic until the next qos apply. If the rule has been modified recently, the changes will not be
effective until the next qos apply.
output definitions
+
Indicates that the policy rule has been modified or has been created
since the last qos apply command.
From
Prec
Where the rule originated.
The precedence of the rule. Precedence determines the order in which
the switch will apply rules.
Enable
Inactive
Reflexive
Log
Whether or not the rule is enabled.
Whether or not the rule is currently being enforced on the switch.
Whether the rule is reflexive or not.
Whether the log is activated or not.
Cnd/Act
The condition and the action associated with the rule; configured
through the policy condition and policy action commands respectively.
OmniSwitch Troubleshooting Guide September 2005
page 10-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
Validation
In order to validate the policy which are not applied yet (pending policies) or you may want to see how
theoretical traffic would be classified by policies that are already applied on the switch, the show policy
classify CLI command can be used.
-> show policy classified L3 applied
The switch will display information about the potential L3 traffic and attempt to match it to a policy
(applied policies only).
-> show policy classified L3
The same as above but this time attempt to match to applied and pending policies.
Note. The following test might result in an invalid combination of condition/action parameters.
Example 1
This policy denies access to subnet 192.168.20.0 from any source.
-> policy condition BLOCK_20 destination ip 192.168.20.0 mask 255.255.255.0
-> policy action BLOCK_20 disposition deny
-> policy rule BLOCK_20 condition BLOCK_20 action BLOCK_20
A theoretical traffic going to 192.168.20.4 can be tested against that policy as following:
-> show policy classify L3 destination ip 192.168.20.4
Packet headers:
L2:
*Port
*MAC
*VLAN
:
:
:
0/0 (any) -> 0/0 (any)
000000:000000 -> 000000:000000
0 ->
0
*802.1p : 0
L3/L4:
*IP
:
0.0.0.0 -> 192.168.20.4
*TOS/DSCP: 0/0
Using pending l3 policies
Classify L3:
*Matches rule 'BLOCK_20': action BLOCK_20 (deny)
In this example, the display indicates that the switch found a rule, BLOCK_20, to classify destination traf-
fic with the specified Layer 3 information.
Example 2
This policy allows TFTP traffic (IP protocol = 17 =UDP; UDP port =69 = TFTP) from subnet
192.168.10.0 to the outside.
-> policy condition oktftp destination ip port 69 ip protocol 17 source ip
192.168.10.0 mask 255.255.255.0
-> policy action oktftp disposition accept
-> policy rule oktftp condition oktftp action oktftp
page 10-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
What happens when some traffic comes in for ip destination port 80? Since it does not satisfy condition
“oktftp”, it depends on the global disposition for router and bridged traffic (qos default routed
disposition and qos default bridged disposition). In our case, the global disposition is default; i.e. accept.
We will receive the result below to accept the traffic when no rules are matched.
-> show policy classify L3 destination ip port 80 /* just to test the rule */
Packet headers:
L2:
*Port
*MAC
*VLAN
:
:
:
0/0 (any) -> 0/0 (any)
000000:000000 -> 000000:000000
0 ->
0
*802.1p : 0
L3/L4:
*IP
:
0.0.0.0 -> 0.0.0.0
*TOS/DSCP: 0/0
Using pending l3 policies
Classify L3:
*No rule matched: (accept)
Example 3
This policy allows TFTP traffic (specified in the condition by IP protocol 17 and UDP port 69) from
subnet 192.168.10.0 to the outside but denies any other traffic to go out from this subnet.
-> show configuration snapshot qos
qos disable stats interval 30 log level 7 log console
policy condition noip source ip 192.168.10.0 mask 255.255.255.0
policy condition oktftp source ip 192.168.10.0 mask 255.255.255.0 ip protocol 17
destination ip port 69
policy action noip disposition deny
policy action oktftp
policy rule oktftp precedence 200 condition oktftp action oktftp
policy rule noip precedence 100 condition noip action noip
-> show policy rule
Policy
From Prec Enab Inact Refl Log Save
oktftp
cli 200 Yes
No No No Yes
Cnd/Act:
oktftp -> oktftp
noip
Cnd/Act:
cli 100 Yes
noip -> noip
No No No Yes
The policy rules can be tested for TFTP traffic coming from subnet 192.168.10.0:
-> show policy classify L3 destination ip port 69 ip protocol 17 source ip
192.168.10.0
Packet headers:
L2:
*Port
*MAC
*VLAN
:
:
:
0/0 (any) -> 0/0 (any)
000000:000000 -> 000000:000000
0 ->
0
*802.1p : 0
L3/L4:
OmniSwitch Troubleshooting Guide September 2005
page 10-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
*IP
*UDP
:
:
192.168.10.0 -> 0.0.0.0
0 -> 69
*TOS/DSCP: 0/0
Using pending l3 policies
Classify L3:
*Matches rule 'oktftp': action oktftp (accept)
In this example, the display indicates that the switch found a rule, “oktftp”, to classify destination traffic
with the specified Layer 3 information.
Correction
If the policy is found invalid, you can use the qos revert CLI command. This command ignores any pend-
ing policies (any additions, modifications, or deletions to the policy configuration since the last qos apply)
and writes the last applied policies to the pending configuration.
Note. Use the qos revert CLI command to delete any QoS configuration that has not been applied to the
configuration through the qos apply command.
In some cases, you may want to remove all of your rules (pending and applied) and start over again.
Note. Use the qos flush CLI command to deletes any QoS configuration that has been applied to the
configuration through the qos apply command.
To return the global QoS configuration to its default settings, use the qos reset CLI command. The
defaults will then be active on the switch.
Note. Use the qos reset CLI command to reset the QoS configuration to its defaults.
Reflexive Rules
Forgetting to set a rule to be reflexive could be the cause of troubles. Ask yourself when you configure a
rule, “what about the reverse flow?”
Note. The OmniSwitch 6624/6648 does not support reflexive rules; you have to configure a rule for the
reverse flow.
When implementing unidirectional layer 3 rules, make sure to address the policy for the reverse flow. By
default, the reverse flow is treated like a “standalone” flow and policy rules need to be configured to
address the reverse flow. On the other hand, implementing reflexive rules address both directions of a
flow, eliminating the need for specific rules for the reverse flow.
Reflexive policies allow a reverse flow back through the switch when the reverse flow would normally be
denied. If a rule is reflexive, the reply packets will be filtered the same as the initial flow.
page 10-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
For example, a TFTP session in one direction will prompt a reply back from the host. If a policy is created
to deny traffic from that host to the switch, the replies from the host will still be accepted on the switch if
the TFTP session policy is configured as a reflexive policy.
If we do not define the rule “oktftp” below, no TFTP session would take place between TFTP client
192.168.10.4 and TFTP server 192.168.20.10.
-> policy condition noip destination ip 192.168.10.0 mask 255.255.255.0
-> policy condition oktftp source ip 192.168.10.0 mask 255.255.255.0 ip
protocol 17 destination ip port 69
-> policy action noip disposition deny
-> policy action oktftp
-> policy rule oktftp precedence 200 condition oktftp action okftp reflexive
-> policy rule noip precedence 100 condition noip action noip
-> qos apply
Another problem could be that the reflexive timer is too low. When reflexive policy rules are configured
and traffic that matches a reflexive rule arrives on the switch, the switch will wait for the reverse flow.
When the timer expires, the reflexivity will not be effective anymore. To change the timeout, enter the qos
reflexive timeout CLI command with the desired number of seconds.
Typically Layer 3 ACLs are configured to be reflexive. Reflexive policies are only supported for TCP or
UDP traffic. Dynamic port negotiation is not supported.
QoS Log
The QoS software in the switch creates its own log for QoS-specific events. By default the QoS log
displays a maximum of 256 lines. To change the maximum number of lines that may display or change the
level of detail given in the log.
To change the number of lines in the log use the qos log lines CLI command. To change the log level use
the qos log level CLI command.
Log events may also be forwarded to the console in real time by using the qos log console CLI command.
To display information about any QoS rules on the switch, use the qos debug CLI command with the
rules keyword (i.e., debug qos rules).
To change the type of debugging, use no with the relevant type of information that you want to remove.
For example:
-> debug qos no rules
To turn off debugging (which effectively turns off logging), enter the following CLI command:
-> no debug qos
Enter the qos apply CLI command to save the changes.
The qos log level CLI command configures the level of detail for these messages. The level of log detail is
in the range from 1 (least detail) to 9 (most detail).
OmniSwitch Troubleshooting Guide September 2005
page 10-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
To view the QoS log, use the show qos log command. The display is similar to the following:
-> show qos log
**QOS Log**
Validate classify: valid
Conditionop noip (3)
Validate condition: valid
Conditionop noip (3)
Validate condition: valid
Conditionop noip (1)
Actionop noip (3)
Validate action: valid
Actionop noip (1)
Ruleop(0) noip (3)
Validate rule: valid
Ruleop(0) noip (3)
Validate rule: valid
Ruleop(0) noip (1)
Update rule 0 with flags 9000402f
Update cond noip for rule 0 (1)
Update QOS_CONDITION_NAME for rule 0 (1)
Update QOS_CONDITION_SRCIPADDRMASK for rule 0 (1)
Classify on item 75 for 0 (1,1)
Update QOS_CONDITION_L3SRCIPADDR for rule 0 (1)
Update QOS_CONDITION_L3SRCIPMASK for rule 0 (1)
Update QOS_CONDITION_STATUS for rule 0 (1)
Validate classify: valid
Validate classify: valid
Validate config: valid
Validate config: valid
Apply QoS configuration
Validate config: valid
Validate config: valid
Apply QoS configuration
Ruleop(0) oktftp (2)
Validate rule: valid
Ruleop(0) oktftp (2)
Validate rule: valid
Ruleop(1) oktftp (0)
Update cond oktftp for rule 1 (0)
page 10-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
QoS Statistics
The show qos statistics CLI command displays statistics about the global QoS configuration as shown
below:
-> show qos statistics
QoS stats
Events
Matches
Drops
L2:
L3 Ingress:
L3 Egress:
IGMP Join:
21
0
0
2
0
0
0
1
0
0
0
0
Fragments: 0
Bad Fragments: 0
Unknown Fragments: 0
Sent NI messages: 9
Received NI messages: 4322
Failed NI messages: 0
Load balanced flows: 0
Reflexive flows: 0
Reflexive correction: 0
Flow lookups: 0
Flow hits: 0
Max PTree nodes: 0
Max PTree depth: 0
Flow hits: 0
output definitions
Events
The number of Layer 2 or Layer 3 flows transmitted on the switch.
The number of Layer 2 or Layer 3 flows that match policies.
The number of Layer 2 or Layer 3 flows that were dropped.
Matches
Drops
Note. See the Omniswitch CLI Reference Guide for more information.
Debug QoS
The CLI command debug qos option configures the type of QoS events that will be displayed in the QoS
log. This command has the following syntax:
debug qos [info] [config] [rule] [main] [route] [hre] [port] [msg] [sl] [mem] [cam] [mapper] [flows]
[queue] [slot] [l2] [l3] [classifier] [nat] [sem] [pm] [ingress] [egress] [rsvp] [balance] [nimsg]
OmniSwitch Troubleshooting Guide September 2005
page 10-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
Debug QoS Internal
The CLI command debug qos internal displays debugging information for QoS internal to the switch.
This command has the following syntax:
debug qos internal “[slice slot/slice] [flow] [queue] [port] [l2tree] [vector] [pending] [verbose]
[mapper] [pool] [log]”
One of the most useful commands to debug all your QoS policy rules is debug qos internal slice/slot flow
where slot is the slot number and slice is the slice (ASIC) number. On the OmniSwitch 7700/7800, each
slot has one slice (slice 0). On the OmniSwitch 8800, each slot may have up to 4 slices (slices 0 to 3). On
the OmniSwitch 6624/6648, each block of 24 ports makes up a slice (slice 0 and slice 1). (The uplink slots
are part of slice 0.)
-> debug qos internal "slice 1/0 flow"
L3 Flows (3 entries):
QID CAM P
Flow
Timeout
*0002d: 0 TCP ( 0) 192.168.10.11:*
- 192.168.20.11:20
HRE
HRE
(rule 0, flags 00006001 vpn 0 pdi 5 HREDONE accept)
*0002d: 0 TCP ( 0) 192.168.10.11:*
- 192.168.20.11:21
(rule 1, flags 00006001 vpn 0 pdi 5 HREDONE accept)
*fffff: 0 UDP ( 0) 192.168.10.11:*
-255.255.255.255:*
240
(rule 2, flags 00002001 vpn 29 pdi 0 FORHRE deny)
output definitions
QID
P
Queue ID Identifying the physical port. Range 0- 512.
The IP port.
Rule
Vpn
Pdi
The rule number in QoS policy configuration file.
The virtual port number.
The priority descriptor index. Used to match an entry in the PDI or
DSCP table, which contains the QoS policies.
HREDONE
Flow
The result of the classification by the HRE.
The flow with the format IP address:port.
page 10-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
OmniSwitch 6624/6648 Dshell Troubleshooting
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
qosIxHelp
dshell->qosIxeHelp
???? Example output of qosIxHelp needed ????
qosDBState
Shows the IP and CAM usage and Semaphore.
Working: [Kernel]->qosDBState
protectDataMutex ID: 0x0000078f
protectDataMutex : 0x6a78920
DB status:
Semaphore Id
Semaphore Type
Task Queuing
Pended Tasks
Owner
: 0x6a78920
: MUTEX
: PRIORITY
: 0
: NONE
IP count 40
Mac count 79
value = 13 = 0xd
Working: [Kernel]->
QoS Dump
There are several QoS DUMP as well: qosL2Dump, qosL3Dump, and qosL4Dump. The most useful
dump is qosL3DumpC "IP", as show below:
Working: [Kernel]->qosL3DumpC "51.51.51.200"
Count IP
Subnet
NHMac
NSR
INGR VLAN QVID EGR0 EGR1 IR TG BC
33: 051.051.051.200 00:00:00:00:00:00 3/25 0110 0000 03/25 -1/-1 0/-1 0/-1 0/-1
051.051.051.000 255
output definitions
IP
IP address
NHMAC
Next Hop MAC address. Should match the ARP entry for the IP
address.
INGR
VLAN
Ingress slot/port. The source port for the packet containing the IP
address as the source IP.
Ingress VLAN ID. The VLAN for the INGR port.
OmniSwitch Troubleshooting Guide September 2005
page 10-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Troubleshooting QoS
output definitions (continued)
QVID
Egress VLAN ID. A value appears in this field if the packet is being
routed to the destination IP address, which is the address that appears in
the IP field.
EGR0
EGR1
IR
The egress slot/port on ASIC 0. The port that will forward a routed
packet to the destination IP address, which is the address that appears in
the IP field. EGR0 must be equal to EGR1. A -1 in this field indicates
that packets cannot be routed to the IP on this slot.
The egress slot/port on ASIC 1. The port that will forward a routed
packet to the destination IP address, which is the address that appears in
the IP field. EGR0 must be equal to EGR1. A -1 in this field indicates
that packets cannot be routed to the IP on this slot.
Ignore routing. Packets to this IP are switched and not routed on this
ASIC. The value of this field is usually 1 on all ASICs, except the
ASIC where the address resides. A value of 0 on all ASICs may indi-
cate that the ARP for the IP address is not yet available.
TG
BC
Tagged, if 1 set the QVID value on the egress routed packet, if the
egress port (as indicated by EGR0 EGR1) is tagged.
If 1 this is an IP broadcast packet, and packets to this destination IP are
flooded out on the ports of the egress VLAN.
subnet
NSR
The IP subnet.
Always 255.
page 10-14
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting QoS
Example QoS Rules
Example QoS Rules
See below for the steps to create a rule for blocking an offending MAC address using the CLI on the
OmniSwitch. Please note the rule does not take effect until you use the qos apply CLI command. Any time
you make a change you need to reissue the qos apply command for it to take.
To setup the Rule and have it run:
-> policy condition block_mac source mac 00:02:A5:1E:E3:6C
-> policy action block_mac disposition deny
-> policy rule block_mac condition block_mac action block_mac
-> qos apply
To view QoS policy rules (example of a traffic-shaping rule):
-> show configuration snapshot qos
! QOS :
qos stats interval 30 log level 7 log console
policy condition ip_traffic2 source ip 192.168.10.20
policy action BW maximum bandwidth
40.0M
policy rule flowShape condition ip_traffic2 action BW
qos apply
To disable the Rule:
-> policy rule block_mac disable
-> qos apply
To verify rule is active:
-> show active policy rule
Policy
From Prec Enab Inact Refl Log Save Matches
block_mac
Cnd/Act:
cli
0 Yes
No No No Yes
1
block_mac -> block_mac
To delete the rule:
-> no policy rule block_mac
-> qos apply
To delete the whole rule set:
-> no policy rule block_mac
-> no policy condition block_mac
-> no policy action block_mac
-> qos apply
To delete all QoS:
-> qos flush
-> qos apply
OmniSwitch Troubleshooting Guide September 2005
page 10-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Example QoS Rules
Troubleshooting QoS
Example of a traffic shaping rule:
-> qos stats interval 30 log level 7 log console
-> policy condition ip_traffic2 source ip 192.168.10.20
-> policy action BW maximum bandwidth
40.0M
-> policy rule flowShape condition ip_traffic2 action BW
-> qos apply
Example of a Layer 2 ACL:
-> policy condition block_mac source mac 00:02:A5:1E:E3:6C
-> policy action block_mac disposition deny
-> policy rule block_mac condition block_mac action block_mac
-> qos apply
Example of a QoS mapping rule:
-> qos trust ports
-> policy map group Group2 1-2:5 4:5 5-6:7
-> policy condition QoS_map source ip 192.168.11.0 mask 255.255.255.0
-> policy action Map1 map tos to dscp using Group2
-> policy rule R1 condition QoS_map action Map1
-> qos apply
page 10-16
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Troubleshooting ARP
The OmniSwitch supports Address Resolution Protocol (ARP). In order to troubleshoot issues related to
ARP, a basic understanding of the protocol is required. Some basic concepts are covered in the sections
below.
RFCs supported
IETF RFC 826
Reading the IETF RFC 826 specification is highly recommended to anyone implementing or troubleshoot-
ing an ARP issue on their network. Reading “Configuring IP” in the appropriate OmniSwitch Network
Configuration Guide is also highly recommended.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 11-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ARP Protocol Failure
Troubleshooting ARP
ARP Protocol Failure
Gateway
Gateway
00:d0:95:79:62:d1
00:d0:95:79:62:8b
Segment: A
Segment: B
Workstation: A
08:00:20:a8:f0:8a
Workstation: B
00:C0:4F:04:6C:2A
If device A is not able to communicate with device B, it could be a result of ARP resolution failure. To
troubleshoot ARP the first reference point is to make sure that the MAC address of device A and device B
are learned on the right port and in correct VLAN.
Use the following command syntax:
show mac-address-table slot number
In our case we have a device connected in slot 16, so the command to verify the MAC address is as
follows:
-> show mac-address-table slot 16
Legend: Mac Address: * = address not valid
Vlan
------+-------------------+--------------+-----------+------------+-----------
10 08:00:20:a8:f0:8a learned 10800 bridging 16/2
Total number of Valid MAC addresses above = 1
Mac Address
Type
Protocol
Operation
Interface
This command displays that MAC Address 08:00:20:a8:f0:8a, belonging to Device A, is learned on port
16/2 and in VLAN 10.
A more comprehensive look for all the MAC addresses learned by the switch can be done by using the
show mac-address-table command. For example:
-> show mac-address-table
Now, verify that the gateway defined in device A points towards the correct IP address. In our case, the
gateway of device A is defined as 10.10.42.1.
page 11-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting ARP
ARP Protocol Failure
When device A ARPs for the gateway IP address exist on the switch, an associated ARP cache entry is
created by the switch. This entry can be viewed by using the show arp command.
To search for a specific ARP entry, use the following command syntax:
show arp ip-address
For example:
-> show arp 10.255.11.219
Total 39 arp entries
Flags (P=Proxy, A=Authentication, V=VRRP)
IP Addr
-----------------+-------------------+----------+-------+--------+-----------
10.10.42.159 08:00:20:a8:f0:8a DYNAMIC 16/ 2 vlan 10
Hardware Addr
Type
Flags Port
Interface
To search for an ARP entry associated with a MAC address use the following command syntax:
show arp mac-address
For example:
-> show arp 10.255.11.219
Total 39 arp entries
Flags (P=Proxy, A=Authentication, V=VRRP)
IP Addr
-----------------+-------------------+----------+-------+--------+-----------
10.10.42.159 08:00:20:a8:f0:8a DYNAMIC 16/ 2 vlan 10
Hardware Addr
Type
Flags Port
Interface
This confirms that the switch has learned the ARP entry of the device A.
Now, device A should have also resolved the ARP entry to the gateway IP address. It can be verified on
the workstation’s command prompt using the following DoS command:
C:\> arp -a
Interface: 10.10.42.1 on Interface 0x1000003
Internet Address
10.10.42.1
Physical Address
00-d0-95-79-62-d1
Type
dynamic
OmniSwitch Troubleshooting Guide September 2005
page 11-3
Download from Www.Somanuals.com. All Manuals Search And Download.
ARP Protocol Failure
Troubleshooting ARP
To confirm the MAC address of the routing instance, use the following command:
-> show ip interface vlan 10
vlan 10
Link type
= ETH_II,
= UP,
Link status
SNMP interface index
Interface index
Enable IP forwarding
Administrative status
Operational status
Enable trap
= 13600010
= 4
= YES,
= ENABLED,
= ACTIVATED,
= NO,
Internet address
Broadcast address
Subnet mask
= 10.10.42.1,
= 10.10.42.255,
= 255.255.255.0,
= 00:d0:95:79:62:d1,
= 00:00:00:00:00:00,
= 00:00:00:00:00:00,
= 1500
Hardware address
Vrrp MAC
Auth MAC
Maximum Transfer Unit (MTU)
Packets received
Packets sent
= 1969,
= 12094,
= 55510,
= 774556,
= 0,
Bytes received
Bytes sent
Multicast packets received
Multicast packets sent
Broadcast packets received
Broadcast packets sent
Input errors
= 10122,
= 0,
= 4,
= 0
Output errors
= 0
Collisions
= 0
Dropped
= 0
Similar steps should be taken to verify the ARP resolution on the other device B.
page 11-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting ARP
Common Error Conditions
Common Error Conditions
If the ARP is not getting resolved in either of the two workstations, then the following conditions may
exist:
• General health of the switch or NI.
• Physical link status might not be operational
• MAC address not learned on the port
• ARP request not reaching the switch, which may be possible because:
- The workstation is not sending an ARP request
- The workstation is not able to understand the ARP request
- ARP packet might have got corrupted
- Duplicate IP addresses configured on the workstations in the same VLAN
OmniSwitch Troubleshooting Guide September 2005
page 11-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced ARP Troubleshooting
Troubleshooting ARP
Advanced ARP Troubleshooting
If the MAC addresses is already learned on the port and the ARP is not getting resolved then we can
further troubleshoot on the switch to see if the ARP request is reaching the switch and switch is respond-
ing back.
To troubleshoot the ARP packets we need to use the diagnostic CLI commands. Precaution must be taken
when using these commands as it might dump a lot of information on the screen.
The command to use is as follows:
-> debug ip packet start ip-address 10.10.42.159 start
-> 16 R 16/2 080020a8f08a->(ffffffffffff) ARP Request 10.10.42.159->10.10.42.1
16 S 16/2 00d0957962d1->080020a8f08a ARP Reply 10.10.42.1->10.10.42.159
16 R 16/2 080020a8f08a->00d0957962d1 IP 10.10.42.159->10.10.42.1 ICMP 8,0 seq=0.
16 S 16/2 00d0957962d1->080020a8f08a IP 10.10.42.1->10.10.42.159 ICMP 0,0 seq=0.
-> debug ip packet stop
The above capture shows that a request for ARP came in on slot 16 port 2 for ip address 10.10.42.1. The
reply was sent by the switch to 10.10.42.159 at MAC address 08:00:20:a8:f0:8a.
This confirms that the switch is replying back to the ARP. Now the ARP cache of the workstation should
also show the correct ARP entry for the switch. If not, then a sniffer should be placed between the switch
and the workstation to look at the packets to analyze if the packets are corrupted or either one of the
devices is not responding in the correct format.
If the debug ip packet command does not show any output when specified with IP address then other
variations like traffic from that NI can be analyzed using the command:
-> debug ip packet start board ni 16
-> debug ip packet stop
This command will show all the packets coming in NI 16, so the output will be a little confusing and pack-
ets will have to be filtered to gather the required information.
If none of the above commands show any traffic coming in from the IP address for the device then it will
point towards the physical layer issue. Workstation as well as the physical port to which the workstation is
connected needs to be examined for further analysis.
page 11-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting ARP
Advanced ARP Troubleshooting
Some devices may be silent like printers. They ARP at the time of the bootup but after that they do not
ARP at all. In order to accommodate those devices OmniSwitch allows different choices:
• To increase the ARP time out value. By default the ARP timeout value is set for 300 seconds. It can be
increased up to 1200 seconds using the following command:
-> arp time-out 1200
• MAC Address aging time can also be increased from the default value of 300 seconds to any higher
value using the following command:
-> mac-address-table aging-time <value>
• Silent devices MAC address can be added in the MAC address table as permanent using the following
command:
-> mac-address-table permanent 08:00:20:a8:f0:8a 16/2 10 bridging
Refer to Source learning section for more details about permanent MAC entries.
If the ARP cache of the switch is not showing the correct ARP entries for the edge devices then the
following command can be used to clear the ARP table and re-learn all the ARP entries:
-> clear arp-cache
Note. Clearing the ARP cache might cause a slight interruption in the network, if done at peak hours and
on the Core switch. This will re invoke the process of ARP learning for each and every devices associated
with that particular switch.
OmniSwitch Troubleshooting Guide September 2005
page 11-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting ARP
Dshell Troubleshooting
In order to troubleshoot ARP cache make sure all the steps mentioned in the earlier sections have been
taken. Dshell should be used when no more error collection can be done from the CLI and debug CLI.
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
According to the architecture of BOP, ARP is processed on the NI. It is never sent to the CMM for
processing. This is done to prevent high CPU utilization on CMM and to have distributed ARP. This
feature was implemented in 5.1.1.R03. Software revision before 5.1.1.R03 processed ARP on the CMM,
CMM synchronized the ARP tables with all of the NIs.
With 5.1.1.R03 and onwards ARP is processed on the NI. In normal scenario ARP table on the CMM
which can be displayed using show arp command in the CLI will be the same as the NI arp table. In case,
an ARP entry is missing in the CMM arp table and debug CLI shows that the ARP is getting into the
switch and a reply is being sent by the NI then NI arp table can be viewed using the NI Debugger.
Load the NI debugger and go to the specific NI in question. One needs to be in the correct slot/slice to
view the routing table on that slice. (For more details about loading the NI debugger and going to the
correct slot/slice, please refer to the NI Debugger section.)
NiDebug>>>ipni_arpShow
NiDebug>>>
Slot 16. NI Arp Table
destination
10.10.42.159 08:00:20:a8:f0:8a 481 0x0
10.11.5.1
10.40.105.1
10.40.105.4
10.40.106.1
10.40.106.3
10.40.108.1
10.40.108.3
10.40.108.4
gateway
port la_hold expire
1948474 0
1948e70 0
arp_flags rt_flags
refcnt use vlan
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
10
00:d0:95:6b:4c:eb 12
00:00:5e:00:01:69 29
00:d0:95:79:62:eb 124 0x0
00:00:5e:00:01:6a 29 0x0
00:d0:95:6b:4c:d9 140 0x0
00:00:5e:00:01:6c 29 0x0
0x0
0x0
511
105
105
106
106
108
108
108
108
110
110
110
110
110
111
111
112
112
112
117
117
140
140
141
150
150
211
211
212
0
8e
1946736 0
0
8e
194827b 0
0
8e
00:d0:95:6b:4c:db 172 0x0
00:d0:95:79:65:f0 172 0x0
1948272 0
194790a 0
19488e3 0
10.40.108.129 08:00:20:c0:92:43 172 0x0
10.40.110.1
10.40.110.3
10.40.110.4
10.40.110.139 08:00:20:b1:1c:49 204 0x0
10.40.110.240 00:00:39:2c:6d:0e 204 0x0
10.40.111.3
10.40.111.4
10.40.112.1
10.40.112.3
10.40.112.4
10.40.117.3
10.40.117.4
10.40.140.1
10.40.140.3
10.40.141.3
10.40.150.1
00:00:5e:00:01:6e 29
00:d0:95:6b:4c:dd 204 0x0
00:d0:95:7c:5b:9b 204 0x0
0x0
0
8e
19484c1 0
1946868 0
19484a5 0
1947a84 0
1948453 0
194672c 0
00:d0:95:6b:4c:de 33
00:d0:95:79:65:67 33
00:00:5e:00:01:70 29
00:d0:95:6b:4c:df 284 0x0
00:d0:95:79:65:10 284 0x0
00:d0:95:6b:4c:e3 428 0x0
00:d0:95:7c:48:59 428 0x0
00:00:5e:00:01:8c 29
00:d0:95:6b:4c:e5 12
00:d0:95:6b:4c:e6 12
00:00:5e:00:01:96 29
0x0
0x0
0x0
0
8e
1948273 0
194674f 0
194827d 0
1947cfc 0
0x0
0x0
0x0
0x0
0
8e
194827b 0
194827b 0
0
8e
10.40.150.110 00:d0:95:7c:5b:9c 204 0x0
19482ff 0
1948273 0
194757e 0
10.40.211.3
10.40.211.4
10.40.212.1
00:d0:95:6b:4c:e8 268 0x0
00:d0:95:79:66:48 268 0x0
00:00:5e:00:01:d4 29
0x0
0
8e
page 11-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting ARP
Dshell Troubleshooting
10.40.212.3
10.40.212.4
00:d0:95:6b:4c:e9 300 0x0
00:d0:95:7c:7d:78 300 0x0
1948275 0
1946929 0
1948092 0
1947153 0
194847e 0
1948e5c 0
1948165 0
194693a 0
194673b 0
1945b2a 0
1946746 0
19469e4 0
1948764 0
1948041 0
1948165 0
1948165 0
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
405
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
212
212
212
212
50
50
50
51
52
53
54
56
57
57
57
10.40.212.127 08:00:20:b0:ea:d1 300 0x0
10.40.212.238 00:c0:4f:12:f7:1b 300 0x0
192.168.50.1 00:d0:95:82:05:16 380 0x0
192.168.50.2 00:d0:95:83:e7:81 380 0x0
192.168.50.5 00:d0:95:6a:f5:bb 380 0x0
192.168.51.5 00:d0:95:6a:f5:bc 380 0x0
192.168.52.5 00:d0:95:6a:f5:bd 380 0x0
192.168.53.5 00:d0:95:6a:f5:be 380 0x0
192.168.54.5 00:d0:95:6a:f5:bf 380 0x0
192.168.56.2 00:d0:95:83:e7:87 380 0x0
192.168.57.1 00:d0:95:82:05:1d 380 0x0
192.168.57.2 00:d0:95:83:e7:88 380 0x0
192.168.57.5 00:d0:95:6a:f5:c2 380 0x0
192.168.58.5 00:d0:95:6a:f5:c3 0380 0x0
NiDebug>>>quit
Source Port is shown as 481. It is calculated based on Coronado ports. Each Coronado has 32 ports.
32*16=512 ports is the total Coronado port that can exist on OS7800.
First 15 modules will have 480 ports. The count starts from 0 so ports 0 to 479 exist on the first 15 slots.
480 is the first port on slot 16 and 481 is the second port on slot 16. So, this does confirm that the arp was
learned on port 16/2.
The table on the NI shows all the ARP entries as on the CMM. If a particular NI is having problems to
another NI then the arp table of that NI should also be looked at. The ARP entry for device A does exist
on NI 16, source NI of the device.
If an entry exists on an NI ARP table and is not fully synchronized with all the other NIs then the problem
might be because the IPC message is lost from that NI to the CMM which holds the master ARP table.
This will result in un synchronized ARP across the NIs which will cause problems when routing between
NIs.
To look at the number of ARP entries being added and deleted in the switch use the following command:
Working: [Kernel]->ipedrArpStatShow
arp add : 3
arp add fail : 0
arp del : 3
arp del fail: 1
arp change : 0
arp refresh : 0
arp putlist : 0
value = 0 = 0x0
Working: [Kernel]->
If arp add, del and fail are changing in large numbers then it might indicate unusual activity in the network
which may be a result of some virus or spoof attack. In normal conditions the entries should be quite
stable.
If everything from the switch point of view looks fine then the best tool to find out the source of the prob-
lem is to use a sniffer.
OmniSwitch Troubleshooting Guide September 2005
page 11-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting ARP
Viewing the ARP Table on OmniSwitch 6624/6648 Switches
To look at the ARP table on OS-6600 use the following command in Dshell:
Working: [Kernel]->ipni_arpShow
Slot 2. NI Arp Table
destination
2.2.2.100
4.4.4.1
4.4.4.100
10.255.13.2
10.255.13.90 00:d0:95:6a:84:51 64
131.118.33.41 00:d0:95:79:64:ab 120 0x0
value = 0 = 0x0
gateway
port la_hold expire
arp_flags rt_flags
refcnt use vlan
00:00:5e:00:01:02 29
00:d0:95:84:07:1e 90
00:00:5e:00:01:04 29
00:20:da:0a:54:10 64
0x0
0x0
0x0
0x0
0x0
0
8e
405
405
405
405
405
05
0
0
0
0
0
0
2
4
4
999
999
336
1ddddf1 0
0
1ddddd1 0
1dded3e 200
1ddec01 0
8e
Working: [Kernel]->
To look at the ARP statistics use the following command in Dshell:
Working: [Kernel]->ipni_arplookup "10.255.13.2"
value = 0 = 0x0
Working: [Kernel]->ipedrArpStatShow
arp add : 3161
arp add fail : 0
arp del : 3155
arp del fail: 0
arp change : 476
arp refresh : 7686
arp putlist : 0
value = 16 = 0x10
page 11-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Troubleshooting
IP Routing
In order to troubleshoot an IP Routing problem, a basic understanding of the IP protocol/feature is
required. Some basic concepts are covered below. Reading RFCs 791, 1812 and 1716 are highly recom-
mended to anyone implementing or troubleshooting IP Routing on their switch/network. IP Routing is a
process by which layer 3 packets are forwarded between two different subnets or networks.
Here is a list of the IP RFCs to review:
• RFC 791 (IP)
• RFC 1812 (Requirements for IP Version 4 Routers)
• RFC 1716 (Towards Requirements for IP Routers)
Here is a list of the RIP RFCs to review:
• RFC 1058 (RIP v1)
• RFC 2453 (RIP v2)
• RFC 1722 (RIP v2 Protocol Applicability Statement)
• RFC 1723 (RIP v2 Carrying Additional Information)
• RFC 1724 (RIP v2 MIB Extension)
Here is a list of the OSPF RFCs to review:
• RFC 2328 (OSPF Version 2)
• RFC 1403 (BGP OSPF Interaction)
• RFC 1587 (The OSPF NSSA Option)
• RFC 1765 (OSPF Database Overflow)
• RFC 2370 (The OSPF Opaque LSA Option)
• RFC 1745 (BGP4/IDRP for IP-OSPF Interaction)
• RFC 1586 (Guidelines for Running OSPF Over Frame Relay Networks)
• RFC 1370 (Applicability statement for OSPF)
• RFC 1850 (OSPF v2 MIB)
Reading the “Configuring IP” chapter in the appropriate OmniSwitch Network Configuration Guide is also
highly recommended.
OmniSwitch Troubleshooting Guide September 2005
page 12-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
Introduction
Introduction
The primary function of IP Routing is processing Layer 3 IP packets and forwarding them in between two
different networks or subnets. This is broken down into two functions. First is determining the best path to
get from one network or subnet to the next and second is to forwarding the packet into that destination
network.
With that being said you need to figure out what type of routing the client is doing. This section will only
go over basic IP Routing. If the client is using an advanced routing protocol such as OSPF, VRRP, RIP II,
etc., please refer to the appropriate sections in the index.
Note. This document does not discuss the basic operation of IP. To learn about how IP works, refer to the
“Configuring IP” chapter in the appropriate OmniSwitch Network Configuration Guide.
IP Routing Protocol Failure
A failure of IP Routing would be a particular device that is unable to get out of the network; you will have
problems getting to a different subnet.
Troubleshooting via the CLI
If devices in different VLANs cannot communicate, we have a routing failure. The first thing to do is
verify the IP setup of the devices in question to make sure they are correct; check for IP address, subnet
mask, and default gateway address on both devices.
If the devices can communicate within their respective VLANs, but not outside of the VLAN, verify the
default gateway is correct for the subnet, and try pinging it. If it responds, the device should be able to get
out of its VLAN without issue.
The next step is to ping the gateway to the destination VLAN. Assuming the Falcon is doing the routing
for the VLANs, this address will show in the output of a show vlan router ip command.
-> show vlan router ip
vlan
ip address
ip mask
encap
mode
oper mtu
------+-----------------+-----------------+---------+---------+------+-----
1
2
192.168.001.001 255.255.255.000
192.168.002.001 255.255.255.000
e2
e2
forward
forward off
on
1500
1500
If the address does not respond to a ping, verify that a port in the VLAN is forwarding via the
show vlan port command. Without an active port in a VLAN, the router instance is not active and
will not respond to pings.
-> show vlan 1 port
port
type
status
--------+---------+--------------
1/1
1/2
1/3
default
default
default
inactive
inactive
inactive
OmniSwitch Troubleshooting Guide September 2005
page 12-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting via the CLI
Troubleshooting IP Routing
.....
4/19
4/20
4/21
4/22
4/23
.....
default
default
default
default forwarding
default inactive
inactive
inactive
inactive
If the destination VLAN gateway address does respond to a ping, there should be no issue with routing,
and the cause is likely to be with Source Learning assuming all other items check out properly (i.e. PC IP
setup, link status, etc.) (see Chapter 2: Managing Source Learning). If source and destination devices can
both ping their respective default gateways and the gateway address to the other VLAN/subnet, the next
step after verifying that Source Learning is functioning properly would be to take a Sniffer trace to see if
in fact the packets are arriving at the destination machine. (Refer to “Troubleshooting with Debug CLI” on
Check for physical issues via the show interfaces command to see if the switch is dropping packets.
-> show interfaces ethernet 4/2
Slot/Port 4/2 :
Operational Status
Type
MAC address
: down,
: Fast Ethernet,
: 00:d0:95:6b:53:95,
BandWidth (Megabits) : 100,
Duplex
: -,
Long Accept
: Enable,
Runt Accept
: Disable,
Long Frame Size(Bytes) : 1553,
Input :
Runt Size(Bytes) : 64
Bytes Received
Lost Frames
Unicast Frames
:
:
:
14397,
0,
6,
Broadcast Frames :
Multicast Frames :
UnderSize Frames :
OverSize Frames :
Collision Frames :
93,
7,
0,
0,
0,
Error Frames
:
0,
CRC Error Frames :
Alignments Error :
Output :
0,
0
Bytes transmitted :
83244,
0,
10,
84,
1106,
0,
Lost Frames
Unicast Frames
:
:
Broadcast Frames :
Multicast Frames :
UnderSize Frames :
OverSize Frames :
Collision Frames :
0,
0,
Error Frames
:
0
Any error conditions in this display should be corrected prior to proceeding.
If you are attempting to ping a device by name rather than by IP address, verify that the name server
configuration is correct, and that the DNS servers in question are functioning, and that the addresses it
returns are correct for the device you are trying to ping.
-> show dns
Resolver is : disabled
page 12-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
Troubleshooting via the CLI
domainName :
nameServer(s):
Verify that the switch has a valid route to the destination subnet via the show ip route command:
-> show ip route
Dest Address
Subnet Mask
Gateway Addr
Age
Protocol
------------------+-----------------+-----------------+---------+-----------
127.0.0.1
255.255.255.255 127.0.0.1
00:14:39 LOCAL
00:13:08 LOCAL
00:14:35 LOCAL
00:14:35 NETMGT
192.168.1.0
192.168.10.0
192.168.10.1
255.255.255.0
255.255.255.0
192.168.1.1
192.168.10.50
255.255.255.255 192.168.11.1
If a route is listed to the destination’s network, you should be able to ping it. If this ping fails, you will
need to determine why. Verify RIP, OSPF, or BGP configurations so that the unit can learn the proper
route to the destination.
The show ip protocols command will tell you what routing protocols are loaded, giving you a starting
point for investigation.
-> show ip protocols
Router ID
Primary addr
RIP status
OSPF status
BGP status
DVMRP status
PIMSM status
Debug level
Debug sections
= 192.168.1.1,
= 192.168.1.1,
= Not Loaded,
= Not Loaded,
= Not Loaded,
= Not Loaded,
= Not Loaded,
= 1,
= none
A traceroute command (tracert in Windows, traceroute from a UNIX/Linux machine, and from the
Falcon CLI) should indicate where the path has failed. If it fails on an intermediate hop between the
Falcon and the destination, your efforts should be expended on the device that showed a failure in the
path. Note that this may lead you back to another device to troubleshoot some other sort of failure, such as
link down, etc. If the traceroute ends at the gateway to the destination VLAN, you do not have a routing
problem, but rather a likely problem in the destination VLAN with either physical issues (cabling, bad
NICs, dropped packets, etc.), Source Learning, or device IP setup.
-> traceroute 192.168.1.2
traceroute to 192.168.1.2, 30 hops max, 40 byte packets
192.168.1.2 50 ms 33.3333 ms 33.3333 ms
The show icmp statistics command may help by giving you an indication of redirect messages being sent.
These usually indicate that the route in question has an issue, and that the router instance knows of a
different route to get to the destination. From there you can look at the show ip route command to see
what your routing table looks like. Verify via this command that the routes you think a packet should take
are properly displayed in the table, and contrast that with any differences noted by the traceroute
command output.
-> show icmp statistics
Messages
Received
Sent
---------------------------+----------+-------------
Total
Error
9579
0
9392
15
OmniSwitch Troubleshooting Guide September 2005
page 12-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting via the CLI
Troubleshooting IP Routing
Destination unreachable
201
15
Time exceeded
Parameter problem
Source quench
Redirect
0
0
0
0
0
0
0
0
Echo request
Echo reply
Address mask request
Address mask reply
9377
0
9377
0
1
0
0
0
The show ip router database command may yield a clue, possibly telling you that an interface that is
designated as a router interface is down or disabled for some reason.
-> show ip router database
Destination
Gateway
Protocol Metric VLAN
-------------------+----------------+--------+------+-----
192.168.1.0/24
192.168.1.0/24
192.168.1.1
192.168.1.1
LOCAL
STATIC 1
1
1
1
Inactive Static Routes
Destination Gateway
Metric
-----------------+--------------+------
If a route shows up as inactive, that must be investigated and corrected.
-> show ip interface
Total 3 interfaces
Name
IP Address
Subnet Mask
Type
Status Forward
---------+---------------+---------------+--------+--------+----------
loopback 127.0.0.1
255.0.0.0
255.0.0.0
ETH_II
ETH_II
UP
DOWN
UP
NO
NO
YES
EMP
24.24.24.24
vlan 1
10.255.11.224 255.255.255.0 ETH_II
Or:
-> show ip interface vlan 1
vlan 1
Link type
Link status
= ETH_II,
= UP,
SNMP interface index
Interface index
Enable IP forwarding
Administrative status
Operational status
Enable trap
= 13600001
= 3
= YES,
= ENABLED,
= ACTIVATED,
= NO,
Internet address
Broadcast address
Subnet mask
= 10.255.11.224,
= 10.255.11.255,
= 255.255.255.0,
Hardware address
Vrrp MAC
Auth MAC
Maximum Transfer Unit (MTU)
Packets received
Packets sent
= 00:d0:95:6a:f4:58,
= 00:00:00:00:00:00,
= 00:00:00:00:00:00,
= 1500
= 239333,
= 168910,
Bytes received
= 42210028,
Bytes sent
Multicast packets received
= 100375790,
= 20802,
page 12-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
Troubleshooting via the CLI
Multicast packets sent
= 0,
= 51008,
= 155,
= 0
Broadcast packets received
Broadcast packets sent
Input errors
Output errors
= 1
Collisions
= 0
Dropped
= 0
The show ip traffic command gives switch-wide statistics for traffic, and the “No Route Discards” statis-
tic should somewhat resemble the “icmp stats destination unreachable” number, in that both numbers
should be increasing at a similar rate. This can be misleading, as a number of “No Route Discards” on a
network is normal; the key here is to see that the numbers are increasing in similar proportion.
-> show ip traffic
Datagrams received
------------------------+------------
Total
426277
IP header error
Destination IP error
Unknown protocol
Local discards
Delivered to users
Reassemble needed
Reassembled
0
2
0
0
249109
0
0
0
Reassemble failed
Datagrams sent
------------------------+------------
Fowarded
1
Generated
178466
Local discards
No route discards
Fragmented
426
15
1
Fragment failed
Fragments generated
0
0
The show tcp ports command displays the TCP connection table.
-> show tcp ports
Local Address
Local Port Remote Address
Remote Port
State
------------------+------------+-----------------+--------------+-------------
0.0.0.0
0.0.0.0
21 0.0.0.0
23 0.0.0.0
0
0
LISTEN
LISTEN
0.0.0.0
80 0.0.0.0
0
LISTEN
0.0.0.0
0.0.0.0
0.0.0.0
10.255.11.228
10.255.11.228
260 0.0.0.0
6778 0.0.0.0
7170 0.0.0.0
23 128.251.17.224
443 0.0.0.0
0
0
0
LISTEN
LISTEN
LISTEN
ESTABLISHED
LISTEN
1677
0
Output fields are described below:
OmniSwitch Troubleshooting Guide September 2005
page 12-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting via the CLI
Troubleshooting IP Routing
output definitions
Local Address
Local IP address for this TCP connection. If a connection is in the LIS-
TEN state and will accept connections for any IP interface associated
with the node, IP address 0.0.0.0 is used.
Local Port
Remote Address
Remote Port
State
Local port for this TCP connection.
Remote IP address for this TCP connection.
Remote port number for this TCP connection.
Describes the state of the TCP connection, as defined in RFC 973. Pos-
sible values are: closed, listen, synSent, synReceived, established,
finWait1, finWait2, closeWait, lastAck, closing, timeWait, and
deleteTCB.
The show udp statistics command displays UDP errors and statistics.
-> show udp statistics
Total datagrams received = 349,
Error datagrams received = 0,
No port datagrams received = 28,
Total datagrams sent
= 317
Output fields are described below:
output definitions
Total datagrams received
Error datagrams received
No port datagrams received
Total number of UDP datagrams delivered to UDP applications.
Number of UDP datagrams that could not be delivered for any reason.
Number of UDP datagrams that could not be delivered for reasons
other than lack of application at the destination.
Total datagrams sent
Total number of UDP datagrams sent from this switch.
The show udp ports command displays the UDP Listener table. The table shows the local IP addresses
and the local port number for each UDP listener.
-> show udp ports
Local Address
Local Port
------------------+--------------
0.0.0.0
0.0.0.0
67
161
Output fields are described below:
output definitions
Local Address
Local Port
Local IP address for this UDP connection.
Local port number for this UDP connection.
page 12-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
Troubleshooting via the CLI
The show ip config command displays IP configuration on the switch:
-> show ip config
IP directed-broadcast = ON,
IP default TTL
= 64
There are user-configurable parameters that can be changed as per requirement. The vlan mtu-ip
command sets the MTU (Maximum Transmission Unit) size for a VLAN.
-> vlan 110 mtu-ip 1500
The show ip interface command displays statistics of a particular IP interface.
-> show ip interface vlan 110
vlan 110
Link type
Link status
= ETH_II,
= UP,
SNMP interface index
Interface index
Enable IP forwarding
Administrative status
Operational status
Enable trap
= 13600110
= 26
= YES,
= ENABLED,
= ACTIVATED,
= NO,
Internet address
Broadcast address
Subnet mask
Hardware address
Vrrp MAC
= 10.40.110.2,
= 10.40.110.255,
= 255.255.255.0,
= 00:d0:95:79:62:c1,
= 00:00:00:00:00:00,
= 00:00:00:00:00:00,
= 1500
Auth MAC
Maximum Transfer Unit (MTU)
Packets received
Packets sent
= 1094,
= 5740,
Bytes received
Bytes sent
= 108592,
= 331560,
= 749,
= 5424,
= 0,
Multicast packets received
Multicast packets sent
Broadcast packets received
Broadcast packets sent
Input errors
= 4,
= 2
Output errors
= 0
Collisions
= 0
Dropped
= 0
The show ip router database command displays a list of all routes (static and dynamic) that exist in the IP
router database. This database serves as a central repository where routes are first processed for redistribu-
tion and where duplicate routes are compared to determine the best route to use. If a route does not appear
in the IP router database list, then the switch does not know about it. In the case of dynamically learned
routes, this could indicate that the route was never received by the switch.
-> show ip router database
Destination
Gateway
Protocol Metric VLAN
-------------------+----------------+--------+------+-----
10.1.96.0/24
10.1.96.0/24
10.1.96.0/24
10.1.96.0/24
10.1.99.0/24
192.168.59.2
192.168.60.2
192.168.61.2
192.168.62.2
192.168.59.2
OSPF
OSPF
OSPF
OSPF
OSPF
1
1
1
1
1
59
60
61
62
59
OmniSwitch Troubleshooting Guide September 2005
page 12-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting via the CLI
Troubleshooting IP Routing
10.1.99.0/24
10.1.99.0/24
10.1.99.0/24
10.11.5.0/24
10.40.100.0/24
10.40.105.0/24
10.40.108.0/24
10.40.110.0/24
192.168.60.2
192.168.61.2
192.168.62.2
10.11.5.2
10.40.100.2
10.40.105.2
10.40.108.2
10.40.110.2
OSPF
OSPF
OSPF
LOCAL
LOCAL
LOCAL
LOCAL
LOCAL
1
1
1
1
1
1
1
1
60
61
62
511
100
105
108
110
page 12-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
Troubleshooting with Debug CLI
Troubleshooting with Debug CLI
As always, being able to obtain a trace of the traffic via a Sniffer application will tell you the bottom line.
If the packets leave the source and arrive at the destination segment properly, the issue does not lie with
routing, the switch, or any intermediate device.
In debug you can look at certain types of traffic crossing through the switch. In this instance, we are look-
ing to see if packets are being transmitted from source to destination, specifically to see if ARP request
and responses are traversing the switch. (These examples are pings being sent to a non-existent IP
address.)
debug ip packet
IP routing can be debugged in debug CLI using the following command:
debug ip packet [start] [timeout seconds] [stop] [direction {in | out | all}] [format {header | text | all}]
[output {console | file filename}] [board {cmm | ni [1-16] | all | none} [ether-type {arp | ip | hex
[hex_number] | all}] [ip-address ip_address] [ip-address ip_address] [ip-pair [ip1] [ip2]] [protocol {tcp
| udp | icmp | igmp | num [integer] | all}] [show-broadcast {on | off}] show-multicast {on | off}]
There are several options available which helps to classify the kind of traffic one may be interested in.
start
Starts an IP packet debug session.
timeout
Sets the duration of the debug session, in seconds. To specify a dura-
tion for the debug session, enter timeout, then enter the session length.
seconds
stop
The debug session length, in seconds.
Stops IP packet debug session.
direction
Specifies the type of the packets you want to debug. Specify in to debug
incoming packets; specify out to debug outgoing packets; specify all to
debug both incoming and outgoing packets.
format
output
Specifies the area of the packet you want to debug. Specify header to
debug the packets header; specify hex to debug the packet text; specify
all to debug the entire packet.
Specifies where you want the debug information to go. Specify console
to print the output to the screen; specify file to save the output to a log
file.
filename
The filename for the output file.
board
Specifies the slot (board) that you want to debug. Specify cmm to
debug CMM packets; specify ni, then enter the slot number of the NI to
debug a network interface card; specify all to debug packets for all
CMMs and NIs on the switch; specify none to clear the previous board
settings.
ether-type
Specifies a specific Ethernet packet type to debug. Specify arp to debug
ARP packets; specify ip to debug IP packets; specify hex and enter an
ethernet packet type in hex format (e.g., 800) to debug a specific ether-
net packet type; specify all to debug all Ethernet packet types.
OmniSwitch Troubleshooting Guide September 2005
page 12-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting with Debug CLI
Troubleshooting IP Routing
ip-address
Specifies an IP address to debug. The debug output will only be for
packets received from this IP address. Enter ip-address, then enter the
IP address that you want to debug.
ip-pair
Use this option to match packets exchanged between two network
addresses. Enter ip-pair, then enter each IP address.
protocol
Specifies a protocol type to debug. Specify tcp to debug TCP packets;
specify udp to debug UPD packets; specify icmp to debug ICMP pack-
ets; specify igmp to debug IGMP packets; specify num to numerically
specify a protocol (e.g., 89); specify all to debug all protocol types.
show-broadcast
show-multicast
Specifies whether or not to display broadcast packets. Specify on to
display broadcast packets on the screen or in the log; specify off if you
do not want to display broadcast packets.
Specifies whether or not to display multicast packets. Specify on to
display multicast packets on the screen or in the log; specify off if you
do not want to display multicast packets.
The debug ip packet command syntax starts IP debugging on NI #1 to show only broadcast packets,
which will include ARPs, and then outputs them to console. For example:
-> debug ip packet start board ni 1 show-broadcast on output console
1 R 1/22 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
1 S CMM 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
1 R 1/22 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
1 S CMM 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
This should be done on the destination machine’s Falcon NI; if the output shows ARP Requests from your
source IP, the issue does not lie with routing.
To stop the output, use the debug ip packet stop command syntax. For example:
-> debug ip packet stop board ni 1 show-broadcast on output console
To be more specific, we can use the debug ip packet command to look only for packets destined to our
troubled destination IP address. For example:
-> debug ip packet start ip-address 192.168.1.24 output console
1 R 1/22 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
1 S CMM 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
1 R 1/22 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
1 S CMM 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
1 R 1/22 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
1 S CMM 00d095206408->(ffffffffffff) ARP Request 192.168.1.2->192.168.1.24
To stop the output, enter the following command syntax:
-> debug ip packet stop ip-address 192.168.1.24 output console
page 12-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
RIP Troubleshooting
RIP Troubleshooting
The following commands are used to troubleshoot RIP failures:
show ip rip interface
show ip rip redis-filter
show ip rip
//check for status enable and version Rip V1 or V2
show ip rip peer
show ip rip routes
show ip rip debug
//level 0 is disabled
7700-> ip rip debug-type ?
^
WARNING TIME SETUP SEND REDIST RECV RDB INFO ERROR
CONFIG ALL AGE
(IP Routing & Multicast Command Set)
To debug RIP:
1) ip rip debug-level 0
2) ip rip debug-type all
3) ip rip debug-level 255
4) ip rip debug-level 0
Verify the required parameters for a RIP interface using the show ip rip interface command:
-> show ip rip interface 11.40.150.1
Interface IP Address
= 11.40.150.1,
= 6,
= disabled,
= enabled,
= None,
= ,
= v1,
= v1,
= 1,
= Active,
= 0,
IP Interface Number (VLANId)
Interface Admin status
IP Interface Status
Interface Config AuthType
Interface Config AuthKey
Interface Config Send-Version
Interface Config Receive-Version
Interface Config Default Metric
RIP Config Status
Received Packets
Received Bad Packets
= 0,
Received Bad Routes
= 0,
Sent Updates
= 0
This interface can be configured for RIP v 1 or RIP v 2. Now, enable the RIP interface using the
command:
-> ip rip interface 10.40.150.1 status enable
->show ip rip interface
Intf Admin IP Intf
vlan status status
Updates
sent/recv(bad)
IP Address
----------------+-----+----------+----------+---------------
11.40.211.4
11.41.211.4
9.9.1.1
2
3
4
enabled
enabled
enabled
enabled
enabled
enabled
0/0(0)
0/0(0)
0/0(0)
OmniSwitch Troubleshooting Guide September 2005
page 12-13
Download from Www.Somanuals.com. All Manuals Search And Download.
RIP Troubleshooting
Troubleshooting IP Routing
11.40.150.1
6
enabled
enabled
0/0(0)
The interface is enabled. Verify that local interface redistribution is enabled, using the commands:
->show ip rip redist
Status: ACT - Active
Protocol Metric
NIS - Not In Service
Route-Tag Status
-------------+-----------+----------+------
LOCAL ACT
1
0
-> show ip rip redist-filter
Control:
All-Sub - All Subnets
Aggreg - Aggregate
No-Sub - No Subnets
Deny - Deny
Permit:
Status:
Perm
ACT
- Permit
- Active
NIS
- Not In Service
Proto Destination
Control Permit Metric Tag Status
-------+---------------------+-------+------+------+-----+------
LOCAL 0.0.0.0/0 All-Sub Perm ACT
0
0
Verify that RIP is enabled globally and redistribution is also enabled, using the command:
-> show ip rip
Status
Host Route Support
= Enabled,
= Enabled,
Redistribution cfg status = Enabled,
Redistribution oper status = Enabled,
Route Tag
Hold Down Timer
= 0,
= 0
Now, verify if the peer relationship is established between the two routers.
-> show ip rip peer
Total Bad
Bad
Secs since
IP Address Recvd Packets Routes Version last update
----------------+------+-------+------+-------+-----------
9.9.1.2
10
12
10
12
12
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
17
17
12
21
12
11.40.150.2
11.40.150.100
11.40.211.1
11.41.211.1
This command shows the number of updates received as well as the time since the last update.
If the peer relationship is not formed then the next thing to look for will be the other router to check if it is
setup correctly.
Now, look at the routing table for RIP protocol, using the command:
-> show ip rip routes
Destination
Mask
Gateway
Metric
------------------+------------------+------------------+-------
0.0.0.0
6.0.0.0
8.0.0.0
9.9.1.0
10.10.41.57
10.10.42.57
0.0.0.0
255.0.0.0
255.0.0.0
255.255.255.0
255.255.255.255
255.255.255.255
11.41.211.1
9.9.1.2
11.40.150.100
9.9.1.1
11.40.211.1
11.41.211.1
2
2
2
1
2
2
page 12-14
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
RIP Troubleshooting
10.10.42.159
11.40.117.0
11.40.150.0
11.40.211.0
11.41.117.0
11.41.211.0
192.168.10.0
255.255.255.255
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
11.41.211.1
11.40.211.1
11.40.150.1
11.40.211.4
11.41.211.1
11.41.211.4
11.40.150.100
2
2
1
1
2
1
2
Notice, that route 6.0.0.0 and 8.0.0.0 appears with the natural subnet mask, even though it is configured to
be class C mask. This is because RIP v1 does not advertise the mask and router always assume the natural
mask.
9.9.1.0 appears with a class C mask because it is locally defined network on the switch. If the protocol
used was RIP v2 then the routing tables will be as follows:
-> show ip rip routes
Destination
Mask
Gateway
Metric
------------------+------------------+------------------+-------
0.0.0.0
6.0.0.0
8.0.0.0
9.9.1.0
10.10.41.57
10.10.42.57
10.10.42.159
11.40.117.0
11.40.150.0
11.40.211.0
11.41.117.0
11.41.211.0
192.168.10.0
0.0.0.0
11.41.211.1
9.9.1.2
11.40.150.100
9.9.1.1
11.40.211.1
11.41.211.1
11.41.211.1
11.40.211.1
11.40.150.1
11.40.211.4
11.41.211.1
11.41.211.4
11.40.150.100
2
2
2
1
2
2
2
2
1
1
2
1
2
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
At this point the route tables should be coherent and the end users should be able to reach any portion of
the network.
In case of any RIP problems debug CLI commands can be used to troubleshoot the protocol. By default,
debug of RIP is disabled with the debug-level of 0. The debug levels set by default can be seen by the
following command:
-> show ip rip debug
Debug Level
Types/Sections
error
= 0
= on
warning
recv
send
rdb
age
config
redist
info
setup
time
= off
= off
= off
= off
= off
= off
= off
= off
= off
= off
In case of any problems with protocol operation of RIP different kinds of debug messages can be turned
on to look at the protocol operations being performed by the switch. Debug level 255 is the highest.
Following is the details of the different debug-types:
OmniSwitch Troubleshooting Guide September 2005
page 12-15
Download from Www.Somanuals.com. All Manuals Search And Download.
RIP Troubleshooting
Troubleshooting IP Routing
error
warning
recv
send
rdb
Includes error conditions, failures, processing errors, etc.
Includes general warnings, non-fatal conditions.
Enables debugging in the receive flow path of the code.
Enables debugging in the send flow path of the code.
Debugs RIP database handling.
age
Debugs code handling database entry aging/timeouts.
Debugs redistribution code.
redist
info
Provides general information.
setup
time
all
Provides information during initialization.
Debugs timeout handler.
Enables all debug options.
Any combination of debug-types can be set.
Lets look at all the RIP debug messages by using the option all:
-> ip rip debug-type all
-> ip rip debug-level 255
tRip-: processRipNetQueue: Enter.
tRip-: processRipNetQueue: Received RIP packet:24
tRip-: ripRecv:Received packet from 11.40.211.4
tRip-: ripRecv:Received my own packet on VLAN 2
tRip-: processRipNetQueue: Received RIP packet:244
tRip-: ripRecv:Received packet from 11.40.211.1
tRip-: ripRecv: Rx: RESP ver=v1 src=11.40.211.1 inIf=11.40.211.4 port=520
tuples=12 len=244
(Received RIP packet from interface 11.40.211.1, version 1 with 12 routes.)
tRip-: ripPeerLookupEntry: looking for peer->11.40.211.1
tRip-: ripPeerAddEntry: Adding Peer->11.40.211.1 to PeerTable
tRip-: ripPeerLookupEntry: looking for peer->11.40.211.1
tRip-: ripPeerRefreshAgeoutTimer: peer->11.40.211.1 age set to 68
tRip-: ripPeerLookupEntry: looking for peer->11.40.211.1
(Looking in peer table, if the peer 11.40.211.1 already exists or not.)
tRip-: in ripRdbLookup for 0.0.0.0 (0.0.0.0)
tRip-: Adding 0.0.0.0/0->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 6.0.0.0 (255.0.0.0)
tRip-: Adding 6.0.0.0/8->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 8.0.0.0 (255.0.0.0)
tRip-: Adding 8.0.0.0/8->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 10.10.41.57 (255.255.255.255)
tRip-: Adding 10.10.41.57/32->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 10.10.42.57 (255.255.255.255)
tRip-: Adding 10.10.42.57/32->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 10.10.42.159 (255.255.255.255)
tRip-: Adding 10.10.42.159/32->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 11.40.1.0 (255.255.255.0)
page 12-16
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
RIP Troubleshooting
tRip-: Adding 11.40.1.0/24->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 11.40.117.0 (255.255.255.0)
tRip-: Adding 11.40.117.0/24->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 11.40.150.0 (255.255.255.0)
tRip-: Adding 11.40.150.0/24->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 11.41.117.0 (255.255.255.0)
tRip-: Adding 11.41.117.0/24->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 11.41.211.0 (255.255.255.0)
tRip-: Adding 11.41.211.0/24->11.40.211.1 to FIB
tRip-: in ripRdbLookup for 192.168.10.0 (255.255.255.0)
tRip-: Adding 192.168.10.0/24->11.40.211.1 to FIB
(Looking for all the received routes in the Routing Database and adding in Forward Information Base
(FIB).)
tRip-: processRipNetQueue: Exit after 2 msgs
tRip-: processRipMsgQ: Enter
tRip-: processRipMsgQ: Received DRC message. payload_len 4
tRip-: Got DRC msg of type 1 from tDrcTm
tRip-: processRipMsgQ: Received DRC message. payload_len 4
tRip-: Got DRC msg of type 0 from tRip
tRip-: ripRdbSendCreateRouteMsg: Adding 12 routes to IPRM database ...
(Adding the received 12 routes in IP Router Manager Database.)
tRip-: ripPeerAgeout: Currtime=69
tRip-: enqueueRipPipeMsg: Enter.
tRip-: processRipMsgQ: Exit after 2 msgs
tRip-: ripMain: Entering select.
tRip-: ripMain: select exited with n 1
tRip-: processRipMsgQ: Enter
tRip-: processRipMsgQ: Received DRC message. payload_len 4
tRip-: Got DRC msg of type 0 from tRip
tRip-: ripPeerAgeout: Currtime=70
tRip-: processRipMsgQ: Received DRC message. payload_len 4
tRip-: Got DRC msg of type 0 from tRip
tRip-: ripPeerAgeout: Currtime=71
tRip-: enqueueRipPipeMsg: Enter.
tRip-: processRipMsgQ: Exit after 2 msgs
tRip-: ripMain: Entering select.
tRip-: ripMain: select exited with n 1
tRip-: processRipMsgQ: Enter
tRip-: processRipMsgQ: Received DRC message. payload_len 4
tRip-: Got DRC msg of type 0 from tRip
tRip-: Entering ripUpdate
(Sending RIP update to the Peer.)
tRip-: ripUpdate: Sending flash update on interface=11.40.211.4, vlan=2
tRip-: ripSupply: Forcing metric for 0.0.0.0 to INFINITY (split horizon)
tRip-: ripSupply:
met=16
Adding tuple(1) dst=0.0.0.0 mask=0.0.0.0 gw=0.0.0.0
tRip-: ripSupply: Forcing metric for 6.0.0.0 to INFINITY (split horizon)
tRip-: ripSupply:
met=16
Adding tuple(2) dst=6.0.0.0 mask=0.0.0.0 gw=0.0.0.0
tRip-: ripSupply: Forcing metric for 8.0.0.0 to INFINITY (split horizon)
tRip-: ripSupply:
met=16
Adding tuple(3) dst=8.0.0.0 mask=0.0.0.0 gw=0.0.0.0
tRip-: ripSupply: Forcing metric for 10.10.41.57 to INFINITY (split horizon)
OmniSwitch Troubleshooting Guide September 2005
page 12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
RIP Troubleshooting
Troubleshooting IP Routing
tRip-: in ripRdbLookup for 10.0.0.0 (255.0.0.0)
tRip-: ripSupply:
gw=0.0.0.0 met=16
Adding tuple(4) dst=10.10.41.57 mask=0.0.0.0
tRip-: ripSupply: Forcing metric for 10.10.42.57 to INFINITY (split horizon)
tRip-: in ripRdbLookup for 10.0.0.0 (255.0.0.0)
tRip-: ripSupply:
gw=0.0.0.0 met=16
Adding tuple(5) dst=10.10.42.57 mask=0.0.0.0
tRip-: ripSupply: Forcing metric for 10.10.42.159 to INFINITY (split horizon)
tRip-: in ripRdbLookup for 10.0.0.0 (255.0.0.0)
tRip-: ripSupply:
gw=0.0.0.0 met=16
Adding tuple(6) dst=10.10.42.159 mask=0.0.0.0
tRip-: ripSupply: Forcing metric for 11.40.1.0 to INFINITY (split horizon)
tRip-: ripSupply:
met=16
Adding tuple(7) dst=11.40.1.0 mask=0.0.0.0 gw=0.0.0.0
tRip-: ripSupply: Forcing metric for 11.40.117.0 to INFINITY (split horizon)
tRip-: ripSupply:
gw=0.0.0.0 met=16
Adding tuple(8) dst=11.40.117.0 mask=0.0.0.0
tRip-: ripSupply: Forcing metric for 11.40.150.0 to INFINITY (split horizon)
tRip-: ripSupply:
gw=0.0.0.0 met=16
Adding tuple(9) dst=11.40.150.0 mask=0.0.0.0
tRip-: ripSupply: Forcing metric for 11.41.117.0 to INFINITY (split horizon)
tRip-: ripSupply:
gw=0.0.0.0 met=16
Adding tuple(10) dst=11.41.117.0 mask=0.0.0.0
tRip-: ripSupply: Forcing metric for 11.41.211.0 to INFINITY (split horizon)
tRip-: ripSupply:
gw=0.0.0.0 met=16
Adding tuple(11) dst=11.41.211.0 mask=0.0.0.0
tRip-: ripSupply: Forcing metric for 192.168.10.0 to INFINITY (split horizon)
Notice that the routes received on the same interfaces are being sent out with metric of 16, split horizon.
tRip-:ripSupply:
met=16
Adding tuple(12) dst=192.168.10.0 mask=0.0.0.0 gw=0.0.0.0
tRip-:ripSupply: Tx RESP ver=v1 dest=11.40.211.255 OutIf=11.40.211.4 dport=520
routes=12 len=244
tRip-:ripPeerAgeout: Currtime=72
This command is useful in understanding the protocol as well as troubleshooting the problem If one has
thorough understanding of the protocol then looking at this capture will help to identify the cause of the
problem.
If the advanced troubleshooting does not help to identify the cause of the problem kindly contact tech-
support for further troubleshooting.
page 12-18
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
OSPF Troubleshooting
OSPF Troubleshooting
The following commands are used to troubleshoot OSPF failures:
show ip ospf interface x.y.z.
show ip ospf area 2.2.2.2
show ip ospf
show ip ospf neighbor
//state is FULL (connect to DR or BDR) or 2 Ways (router to router)
show ip ospf interface
show ip ospf lsdb
//DR or BDR
//within area
A debug-level of 50 for detail and 75 for more detail.
7700-> ip ospf debug-type ?
^
WARNING VLINK TM TIME SUMMARY STATE SPF SETUP
SEND RESTART REDIST RECV RDB MIP LSDB INTF INFO
HELPER HELLO FLOOD ERROR DBEXCH AUTH AREA ALL
AGE
(IP Routing & Multicast Command Set)
To debug OSPF:
1) show ip ospf debug
//level 0 is disabled
2) ip ospf debug-level 0
3) ip ospf debug-type warning
4) ip ospf debug-type error
5) ip ospf debug-type state
6) ip ospf debug-level (50 detail; 75 more detail)
7) ip ospf debug-level 0 //to stop
Verify the required parameters for an OSPF interface using the show ip ospf interface command:
-> show ip ospf interface 10.40.110.2
VLAN Id
= 110,
Interface IP Address
Interface IP Mask
Admin Status
Operational Status
OSPF Interface State
Interface Type
Area Id
Designated Router IP Address
Designated Router RouterId
= 10.40.110.2,
= 255.255.255.0,
= Disabled,
= Up,
= Down,
= Broadcast,
= 0.0.0.5,
= 0.0.0.0,
= 0.0.0.0,
Backup Designated Router IP Address = 0.0.0.0,
Backup Designated Router RouterId
MTU (bytes)
Metric Cost
= 0.0.0.0,
= 1492,
= 1,
Priority
= 1,
Hello Interval (seconds)
Transit Delay (seconds)
Retrans Interval (seconds)
Dead Interval (seconds)
Poll Interval (seconds)
Link Type
= 10,
= 1,
= 5,
= 40,
= 120,
= Broadcast,
= none,
= 0,
Authentication Type
# of Events
OmniSwitch Troubleshooting Guide September 2005
page 12-19
Download from Www.Somanuals.com. All Manuals Search And Download.
OSPF Troubleshooting
Troubleshooting IP Routing
# of Init State Neighbors
# of Exchange State Neighbors
# of Full State Neighbors
= 0,
= 0,
= 0
This interface has been assigned to area 0.0.0.5. OSPF interface status is down because the administrative
status of the OSPF interface is down. If the priority of the interface is set to 0 then this interface will not
participate in the elections for DR and BDR.
Check to verify that the area 0.0.0.5 was created on the switch and is operational.
-> show ip ospf area 0.0.0.5
Area Id
AdminStatus
Type
OperStatus
---------------+-------------+-------------+------------
0.0.0.0
0.0.0.5
enabled
enabled
normal
normal
up
up
Verify that the area-type on both the interfaces is same.
-> show ip ospf area 0.0.0.5
-> show ip ospf area 0.0.0.5
Area Identifier
Admin Status
Operational Status
= 0.0.0.5,
= Enabled,
= Up,
Area Type
Area Summary
= normal,
= Enabled,
= 00h:00m:00s,
= 0,
= 0,
= 0,
Time since last SPF Run
# of Area Border Routers known
# of AS Border Routers known
# of Active Virtual Links
# of LSAs in area
= 0,
# of SPF Calculations done
= 0,
# of Incremental SPF Calculations done = 0,
# of Neighbors in Init State
# of Neighbors in Exchange State
# of Neighbors in Full State
# of Interfaces attached
Attached Interfaces
= 0,
= 0,
= 0,
= 1,
=10..40.110.2
Note, that the interface 10.40.110.2 should appear in the area configuration as an attached interface.
Now, check to see if OSPF is enabled globally.
-> show ip ospf
Router Id
OSPF Version Number
Admin Status
Area Border Router ?
AS Border Router Status
Route Redistribution Status
Route Tag
= 192.168.50.4,
= 2,
= Enabled,
= Yes,
= Enabled,
= Disabled,
= 0,
SPF Hold Time (in seconds)
SPF Delay Time (in seconds)
MTU Checking
= 10,
= 5,
= Disabled,
= 0,
# of Routes
# of AS-External LSAs
# of self-originated LSAs
# of LSAs received
= 0,
= 0,
= 0,
page 12-20
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
OSPF Troubleshooting
External LSDB Limit
Exit Overflow Interval
# of SPF calculations done
= 0,
= 0,
= 0,
# of Incr SPF calculations done = 0,
# of Init State Nbrs
# of Exchange State Nbrs
# of Full State Nbrs
# of attached areas
# of Active areas
= 0,
= 0,
= 0,
= 0,
= 0,
= 0,
= 0
# of Transit areas
# of attached NSSAs
Since, OSPF is enabled globally so enable OSPF on the interface.
-> ip ospf interface 10.40.110.2 status enable
Verify the neighbor relationship between the two routers using the show ip ospf neighbor CLI command.
-> show ip ospf neighbor
IP Address
----------------+----------------+----------------+----+-------+--------
10.40.110.3 0.0.0.5 192.168.50.3 110 Full Master
Area Id
Router Id
Vlan State
Mode
The neighbor relationship is full. Neighbor relationship can be one of the following six states:
Init
Initialization State
2way
The two routers are able to receive hello packets from each other. This
will also be the state when neighbor adjacency is formed with a router
other than DR and BDR
Exstart
Exchange
Load
Starting the synchronization process
Exchanging the database
Performing SPF calculations and loading routes in route table
Neighbors are completely synchronized
Full
To view the DR and BDR for this interface, the following command can be used:
-> show ip ospf interface
IP
Address
DR
Address
Backup DR
Address
Admin
Oper
Vlan Status Status State
----------------+----------------+----------------+----+--------+------+-------
10.40.110.2 10.40.110.3 10.40.110.2 110 enabled up BDR
So, the above command shows that 10.40.110.3 is the Designated Router and 10.40.110.2 is the Backup
Designated Router. So, if there were two more routers in this subnet then they should form full adjacency
with these routers but between themselves they will have 2way relationship. As, all the routes are to be
synchronized by the DR and the BDR.
To look at the Link State Database use the show ip ospf lsdb CLI command:
-> show ip ospf lsdb
Area Id
----------------+-------+----------------+----------------+------------+-----
0.0.0.0 rtr 192.168.50.4 192.168.50.4 0x80000002 10
Type
LS Id
Orig Router-Id
SeqNo
Age
OmniSwitch Troubleshooting Guide September 2005
page 12-21
Download from Www.Somanuals.com. All Manuals Search And Download.
OSPF Troubleshooting
Troubleshooting IP Routing
0.0.0.0
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
0.0.0.5
sumnet 10.40.0.0
192.168.50.4
11.40.211.1
11.41.211.1
192.168.50.3
192.168.50.4
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.4
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
192.168.50.3
0x80000002 5
0x80000041 6
0x80000033 6
0x800000b8 1
0x80000003 5
0x80000007 1
0x80000047 5
0x80000003 5
0x8000007b 2
0x80000002 5
0x80000072 2
0x8000007d 2
0x80000051 5
0x8000003e 5
0x8000003e 5
0x8000003d 5
0x80000051 5
0x8000007f 2
0x8000003f 5
0x8000003f 5
0x8000003b 5
0x8000003a 5
0x8000003d 5
0x8000003d 5
rtr
rtr
rtr
rtr
net
net
net
11.40.211.1
11.41.211.1
192.168.50.3
192.168.50.4
10.40.110.3
10.40.111.3
10.40.212.3
sumnet 10.0.128.0
sumnet 10.10.42.0
sumnet 10.26.0.0
sumnet 10.32.64.0
sumnet 10.190.0.0
sumnet 10.210.0.0
sumnet 10.211.0.0
sumnet 10.216.0.0
sumnet 11.11.1.0
sumnet 192.168.99.0
sumasbr 10.26.0.1
sumasbr 10.45.192.1
sumasbr 10.48.64.1
sumasbr 10.190.0.5
sumasbr 192.168.50.2
sumasbr 192.168.50.6
The Link State table should have all of the routes synchronized between the two neighbors. It will not have
any entries for any external protocol. To look at external link state database use the command:
-> show ip ospf ext-lsdb
LS Id
Orig Router-Id
SeqNo
Age
Protocol
-----------------+------------------+----------+--------+----------
10.0.128.0
10.10.42.0
10.26.64.0
10.32.64.0
10.40.150.0
10.40.150.0
10.40.150.0
10.190.0.0
10.190.0.0
10.210.0.0
10.211.0.0
10.212.0.0
10.213.0.0
10.214.0.0
10.216.0.0
10.217.0.0
11.11.1.0
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
11.40.211.1
11.41.211.1
10.26.0.1
10.48.64.1
10.26.0.1
10.26.0.1
10.26.0.1
10.48.64.1
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
11.40.211.1
11.41.211.1
11.40.211.1
11.40.211.1
11.41.211.1
11.41.211.1
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
0x80000032 123
0x80000032 123
0x80000072 123
0x80000032 123
0x80000032 123
0x80000035 121
0x8000002d 121
0x80000032 123
0x80000028 57
0x80000032 123
0x80000032 123
0x80000032 123
0x80000034 57
0x80000032 123
0x80000032 123
0x80000032 123
0x80000032 123
0x80000036 121
0x8000002d 121
0x80000035 121
0x80000036 121
0x8000002d 121
0x8000002f 121
0x80000032 123
0x80000032 123
0x80000032 123
0x80000032 123
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
11.40.1.0
11.40.1.0
11.40.117.0
11.40.211.0
11.41.117.0
11.41.211.0
192.168.50.0
192.168.51.0
192.168.52.0
192.168.53.0
page 12-22
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
OSPF Troubleshooting
192.168.54.0
192.168.55.0
192.168.56.0
192.168.57.0
192.168.58.0
192.168.59.0
192.168.60.0
192.168.61.0
192.168.62.0
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
10.26.0.1
0x80000032 123
0x80000032 123
0x80000032 123
0x80000032 123
0x80000032 123
0x80000032 123
0x80000032 123
0x80000032 123
0x80000032 123
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
OSPF
These routes may be using RIP v1 or v2, static or local route redistribution. Therefore a separate table is
maintained for all the external link states.
The routing table can be viewed using the following commands:
Now, the routing table should have all of the OSPF routes.
-> show ip route
+ = Equal cost multipath routes
Total 14 routes
Dest Address
Subnet Mask
Gateway Addr
Age
Protocol
------------------+-----------------+-----------------+---------+-----------
10.10.42.0
10.40.108.0
10.40.110.0
10.40.111.0
10.40.112.0
10.40.150.0
10.40.212.0
10.255.13.0
11.40.1.0
11.40.117.0
11.40.211.0
11.41.117.0
11.41.211.0
127.0.0.1
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
10.10.42.1
23:54:47 LOCAL
00:03:07 OSPF
23:54:51 LOCAL
00:03:07 OSPF
00:03:07 OSPF
23:54:51 LOCAL
00:03:07 OSPF
23:55:57 LOCAL
00:03:02 OSPF
00:03:02 OSPF
00:03:02 OSPF
00:03:02 OSPF
00:03:02 OSPF
1d 0h LOCAL
10.40.110.3
10.40.110.2
10.40.110.3
10.40.110.3
10.40.150.2
10.40.110.3
10.255.13.151
10.40.110.3
10.40.110.3
10.40.110.3
10.40.110.3
10.40.110.3
255.255.255.255 127.0.0.1
-> show ip ospf routes
Destination/Mask
Gateway
Metric Vlan
Type
---------------------+-----------------+--------+------+----------
10.10.42.0/24
10.40.0.0/13
10.10.42.1
127.0.0.1
1
2
2
1
2
2
2
2
1
1
1
1
1
10
-1
Intra
Intra
Intra
Intra
Intra
Intra
Intra
Intra
AS-Ext
AS-Ext
AS-Ext
AS-Ext
AS-Ext
10.40.108.0/24
10.40.110.0/24
10.40.111.0/24
10.40.112.0/24
10.40.150.0/24
10.40.212.0/24
11.40.1.0/24
11.40.117.0/24
11.40.211.0/24
11.41.117.0/24
11.41.211.0/24
10.40.110.3
10.40.110.2
10.40.110.3
10.40.110.3
10.40.110.3
10.40.110.3
10.40.110.3
10.40.110.3
10.40.110.3
10.40.110.3
10.40.110.3
110
110
110
110
110
110
110
110
110
110
110
OmniSwitch Troubleshooting Guide September 2005
page 12-23
Download from Www.Somanuals.com. All Manuals Search And Download.
OSPF Troubleshooting
Troubleshooting IP Routing
If local, static, or any other external protocol routes need to be redistributed into OSPF then the first step is
to make that OSPF router to be a AS Border Router. This need OSPF status to be disabled.
-> ip ospf status disable
-> ip ospf asbr
-> ip ospf redist local
-> ip ospf redist-filter 0.0.0.0 0.0.0.0
->ip ospf redist status enable
-> ip ospf status enable
For any redistribution into OSPF, OSPF status needs to be disabled and then re-enabled. This allows all of
the routing tables on the NI to get synchronized.
Debug CLI has some OSPF commands just like RIP which shows the setup process. Debug Level by
default is set to 0. Debug type by default is set for errors.
-> show ip ospf debug
Debug Level
Types/Sections
error
warning
state
recv
send
flood
spf
lsdb
rdb
age
vlink
redist
summary
dbexch
hello
auth
= 0,
= on,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
area
intf
mip
info
setup
time
tm
error
Administratively enables/disables debugging error messages only. Error
messages provide information of program faults.
warning
state
Administratively enables/disables debugging warning messages only.
Administratively enables/disables debugging OSPF state messages only.
State messages show the switch state in relation to its neighbors.
recv
Administratively enables/disables debugging messages for packets
received by OSPF only.
page 12-24
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
OSPF Troubleshooting
send
flood
spf
Administratively enables/disables debugging messages for packets sent
by OSPF only.
Administratively enables/disables debugging messages for the flooding
of Link State Advertisements (LSAs) in OSPF only.
Administratively enables/disables debugging messages for OSPF’s
Shortest Path First (SPF) calculations only.
lsdb
Administratively enables/disables debugging messages for OSPF’s Link
State Database (LSDB) related operations only.
rdb
Administratively enables/disables debugging messages for OSPF’s rout-
ing database (RDB) related operations only.
age
Administratively enables/disables debugging messages for OSPF’s
aging process of LSAs only. LSAs are sent out on a periodic basis.
vlink
redist
summary
Administratively enables/disables debugging messages for OSPF's
virtual links operations only.
Administratively enables/disables debugging messages for OSPF’s
route redistribution process only.
Administratively enables/disables debugging messages for all OSPF's
summarizations only. Summarization of routes can be set for stubby
areas and NSSAs.
dbexch
hello
auth
area
intf
Administratively enables/disables debugging messages for OSPF neigh-
bors’ database exchange only.
Administratively enables/disables debugging messages for OSPF's hello
handshaking process only.
Administratively enables/disables debugging messages for OSPF’s
authentication process only. Authentication can be simple or MD5.
Administratively enables/disables debugging messages for OSPF's area
events only.
Administratively enables/disables debugging messages for OSPF’s
interface operations only.
mip
Administratively enables/disables debugging messages for MIP process-
ing of OSPF specific commands only.
info
Administratively enables/disables debugging messages for purpose to
provide OSPF information only.
setup
time
tm
Administratively enables/disables debugging messages for OSPF’s
initialization setup only.
Administratively enables/disables debugging messages for OSPF’s time
related events only. Timers are set for interfaces and LSAs.
Administratively enables/disables debugging messages for OSPF’s Task
Manager communication events only.
OmniSwitch Troubleshooting Guide September 2005
page 12-25
Download from Www.Somanuals.com. All Manuals Search And Download.
OSPF Troubleshooting
Troubleshooting IP Routing
Let’s look at all the messages that appear on the console during the setup of OSPF adjacency. The enabled
debug types are state, hello and area using the command:
This command is too verbose so special care should be taken when using this command.
-> ip ospf debug-type warning
-> ip ospf debug-type error
-> ip ospf debug-type state
-> ip ospf debug-level 255
(Building Router LSA to advertise on the interface.)
tOspf-: ospfAreaTimer:3356 ospfBuildRouterLsa(area 0.0.0.5, flags 0x5).
[curTime = 7404s]
tOspf-: ospfBuildRouterLsa: Built Router LSA: Area 5 Seq 0x80000001 numLinks 1
Age 0
tOspf-: ospfNbrStateMachine: NBR 10.40.110.3; EVENT HELLORX; STATE DOWN.
(Neighbor state is down, received Hello packet from Neighbor.)
tOspf-: ospfNbrStateMachine: (10.40.110.3) Change! PREV DOWN; EVENT HELLORX;
NEXT INIT.
tOspf-: ospfNbrStateMachine: NBR 10.40.110.3; EVENT 2WAYRX; STATE INIT.
tOspf-: ospfNbrStateMachine: (10.40.110.3) Change! PREV INIT; EVENT 2WAYRX;
NEXT 2WAY.
(Received Hello, neighbor state is 2 WAY.)
tOspf-: ospfNbrStateMachine: NBR 10.40.110.3; EVENT ADJOK; STATE 2WAY.
tOspf-: ospfNbrAdjOk: nbr 10.40.110.3: moving to EXSTART
tOspf-: ospfNbrClearAdjacency: Clearing Adjacency : NBR 10.40.110.3, Intf addr
10.40.110.2
tOspf-: ospfNbrStateMachine: (10.40.110.3) Change! PREV 2WAY; EVENT ADJOK; NEXT
EXSTART.
tOspf-: ospfBuildRouterLsa: Built Router LSA: Area 5 Seq 0x80000002 numLinks 1
Age 0
tOspf-: ospfRecvDD: EXSTART: ddPkt I_M_MS (Master, More, Init) Nbr Addr
10.40.110.3:
len = 0, nbr rtrId = 192.168.50.3, nbr seqnum = 7408000, ddPkt seqnum =
106867000
tOspf-: ospfRecvDD: EXSTART: ddPkt I_M_MS (Slave, noMore, noInit) Nbr Addr
10.40.110.3:
len = 20, nbr rtrId = 192.168.50.3, nbr seqnum = 7408000, ddPkt seqnum
= 7408000
(Negotiating for Master and Slave relationship.)
tOspf-: ospfNbrStateMachine: NBR 10.40.110.3; EVENT NEGODONE; STATE EXSTART.
tOspf-: ospfNbrStateMachine: (10.40.110.3) Change! PREV EXSTART; EVENT
NEGODONE; NEXT EXCHANGE.
tOspf-: ospfNbrStateMachine: NBR 10.40.110.3; EVENT EXCHDONE; STATE EXCHANGE.
Exchange Done with the Neighbor
tOspf-: ospfNbrStateMachine: (10.40.110.3) Change! PREV EXCHANGE; EVENT EXCH-
DONE; NEXT LOADING.
tOspf-: ospfNbrStateMachine: NBR 10.40.110.3; EVENT LOADDONE; STATE LOADING.
tOspf-: ospfBuildRouterLsa: area 0.0.0.5, lsa time = 7408, curTime =
7409.Aborting!
page 12-26
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
BGP Troubleshooting
tOspf-: ospfNbrStateMachine: (10.40.110.3) Change! PREV LOADING; EVENT LOAD-
DONE; NEXT FULL.
(Loading of the LSAs done, spf calculations being done and the routes are getting loaded in the route
table. The state moves to Full with the neighbor.)
tOspf-: ospfAreaTimer:3356 ospfBuildRouterLsa(area 0.0.0.5, flags 0x5).
[curTime = 7410s]
tOspf-: ospfBuildRouterLsa: Built Router LSA: Area 5 Seq 0x80000003 numLinks 1
Age 0
tOspf-: ospfNbrStateMachine: NBR 10.40.110.3; EVENT HELLORX; STATE FULL.
tOspf-: ospfNbrStateMachine: NBR 10.40.110.3; EVENT 2WAYRX; STATE FULL.
tOspf-: ospfNbrStateMachine: NBR 10.40.110.3; EVENT HELLORX; STATE FULL.
Other debug-types may be enabled as per need. The output of this command is verbose so care should be
taken before enabling the debug types.
For further troubleshooting the problem contact tech support.
BGP Troubleshooting
Be sure that the BGP neighbor Operational State is 'established'. The BGP neighbor 'maximum-prefix'
default is 5000. This value may be increased to 65000, which is the limitation of the NI routing table; a
total of 64K route entries. The maximum number of BGP routes will be a subset of this number, depend-
ing on how many other routes exist (RIP, OSPF, etc.). The number of BGP routes can be learn, depends
on the system memory resources.
When the Operation State is idle or active, increasing the maximum-prefix may resolve the issue.
The following commands are used to troubleshoot BGP failures:
show ip bgp neighbors
show ip bgp routes
show ip bgp statistics
show ip bgp aggregate-address
show ip bgp path
show ip bgp network
-> show ip bgp neighbors
Legends: Nbr = Neighbor
As = Autonomous System
Nbr address
As
Admin state Oper state BGP Id
Up/Down
---------------+-----+-----------+------------+---------------+-----------
152.23.1.9
152.23.1.10
227 enabled
227 enabled
established 20.23.24.20
established 20.23.24.17
17h:00m:17s
19h:21m:18s
OmniSwitch Troubleshooting Guide September 2005
page 12-27
Download from Www.Somanuals.com. All Manuals Search And Download.
BGP Troubleshooting
Troubleshooting IP Routing
-> show ip bgp neighbors statistics 152.23.1.9
Neighbor address
# of UP transitions
= 152.23.1.9,
= 4,
Time of last UP transition
# of DOWN transitions
Time of last DOWN transition
Last DOWN reason
# of msgs rcvd
# of Update msgs rcvd
# of prefixes rcvd
= 21d:11h:42m,
= 6,
= 21d:11h:43m,
= hold_timeout,
= 102904,
= 4,
= 1,
# of Route Refresh msgs rcvd
# of Notification msgs rcvd
Last rcvd Notification reason
Time last msg was rcvd
# of msgs sent
= 0,
= 1,
= update message error [malformed aspath]
= 00h:00m:06s,
= 187265,
# of Update msgs sent
# of Route Refresh msgs sent
# of Notification msgs sent
Last sent Notification reason
Time last msg was sent
= 85668,
= 0
= 1,
= hold time out [none]
= 00h:00m:00s,
7700-> ip bgp debug-type ?
^
WARNINGS TM TCP SYNC SENDUPD ROUTE REDIST
RECVUPD POLICY PEER OPEN NOTIFY MIP LOCAL
KEEPALIVE INFO FSM ERRORS DAMP ALL AGGR
(IP Routing & Multicast Command Set)
To debug BGP:
1) ip bgp debug-level 51
2) ip bgp debug-type peer
3) ip bgp debug-type open
4) ip bgp debug-level 0
page 12-28
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
Dshell Troubleshooting Advanced IP Routing
Dshell Troubleshooting Advanced IP Routing
The following Dshell commands are used to troubleshoot advanced IP routing.
ipdbg=x
This command runs on the NI of the 7700/8800. Value can be 'OR'ed (for example, 0x20001000 is 'OR'ed
with IPDBG_DBG and IPDBG_WARN). The most common value is 0x20000000. The default value is
0x10000000. Please run this command with a taskDelay <tick value>. A value of 300 ticks equals 5
seconds. To change to a different module, use the command 'changeslot <slot#>. For the 6600 and 6800,
this command is run directly on the stack in Dshell.
->dshell
1:0 nidbg>ipdbg=0x20000000;taskDelay 600;ipdbg=0x10000000
Working: [Kernel]->ipdbgHelp
IPDBG_IPRCV
IPDBG_ARPRCV
IPDBG_IPSND
IPDBG_ARPSND
IPDBG_DECODE
IPDBG_HEXDMP
0x1
0x2
0x10
0x20
0x100
0x200
IPDBG_ARPTIMER 0x400
IPDBG_DBG
0x1000
0x2000
0x4000
0x8000
0x10000
0x20000
IPDBG_AVLAN
IPDBG_ROUTE
IPDBG_ARP
IPDBG_CMMRCV
IPDBG_CMMSND
IPDBG_CMMDECODE 0x40000
IPDBG_CMMHEX
IPDBG_CMMDBG
IPDBG_CMMDMP
IPDBG_ECMP
IPDBG_VRRP
IPDBG_SOCK
IPDBG_DOS
0x80000
0x100000
0x200000
0x400000
0x800000
0x1000000
0x2000000
IPDBG_PRODSPEC 0x4000000
IPDBG_NOERR
IPDBG_WARN
IPDBG_VERBOSE
IPDBG_HEX
0x10000000
0x20000000
0x40000000
0x80000000
value = 0 = 0x0
Working: [Kernel]->
ifShow
Shows the IP router interfaces on the CMM.
->dshell
Certified: [Kernel]->ifShow
lo (unit number 0):
Flags: (0x8069) UP LOOPBACK MULTICAST ARP R
Type: SOFTWARE_LOOPBACK
OmniSwitch Troubleshooting Guide September 2005
page 12-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting Advanced IP Routing
Troubleshooting IP Routing
Internet address: 127.0.0.1
Netmask 0xff000000 Subnetmask 0xff000000
Metric is 0
Maximum Transfer Unit size is 32768
46 packets received; 46 packets sent
0 multicast packets received
0 multicast packets sent
0 input errors; 0 output errors
0 collisions; 0 dropped
iprmShowRoutes
Shows the types of routes on the CMM.
->dshell
Working: [Kernel]->iprmShowRoutes
tShell-:
TOS Destination
Gateway
Protocol Metric Pri VLAN tShell-:
-
tShell-: 0 0.0.0.0/0
tShell-: 0 128.0.0.0/8
tShell-: 0 172.50.0.0/16 172.50.1.23
172.50.1.254 STATIC-0 1
10.255.13.1 STATIC-0 1
0 0
0 0
0 0
0x0
0x400
0x0
LOCAL -0 1
iprmCountRoutes
Shows the total number of IP routes on the CMM.
->dshell
Working: [Kernel]->iprmCountRoutes
25 routes in IPRM RIB
21 OSPF
0 RIP
1 STATIC
3 LOCAL
0 BGP
0 others
value = 15 = 0xf
ipni_ifShow
Shows the IP router interfaces per NI.
1:0 nidbg> ipni_ifShow
1:0
1:0 fe8 vlan202. [@0x014885a0]
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
Flags 0x1041 State 0x1
Internet address: 169.10.108.3
Netmask 0xfffffc00 Subnetmask 0xfffffc00
Ethernet Address: 00:d0:95:86:88:69
VRRP Ethernet Address: 00:00:00:00:00:00
Maximum Transfer Unit size is 1500
Arp timeout is 300.
If address list pointer 1488510
page 12-30
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
Dshell Troubleshooting Advanced IP Routing
1:0
1:0 fe7 vlan180. [@0x01488690]
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
Flags 0x1041 State 0x1
Internet address: 169.10.208.3
Netmask 0xfffff000 Subnetmask 0xfffff000
Ethernet Address: 00:d0:95:86:88:68
VRRP Ethernet Address: 00:00:00:00:00:00
Maximum Transfer Unit size is 1500
Arp timeout is 300.
If address list pointer 1488600
Iprm_routeShow
Shows the type of routes per NI.
1:0 nidbg> ipni_routeShow
1:0
1:0 Slot 1. NI Routes
1:0 destination
1:0 169.10.0.0
1:0 169.10.8.0
1:0 169.10.8.0
1:0 169.10.32.0
1:0 169.10.64.0
1:0 169.10.80.0
1:0 169.10.108.0
1:0 169.10.128.0
1:0 169.10.160.0
1:0 169.10.176.0
gateway
169.10.0.5
flags refcnt
vlan
5
101
c003
8003
101
0
0
0
0
0
0
0
0
0
0
169.10.0.134
169.10.0.135
169.10.32.3
169.10.64.3
169.10.80.3
169.10.108.3
169.10.128.3
169.10.160.3
169.10.176.3
5
5
120
110
130
202
160
150
140
101
101
101
101
101
101
Ipni_routeCount
Shows the total number of IP routes per NI.
1:0 nidbg> ipni_routeCount
1:0
1:0 routes: 166 ecmps: 156 Unique Destinations: 88 arps: 3017 other: 0
1:0 value = 0 = 0x0
ospfDbgDumpEnv
Working: [Kernel]->ospfDbgDumpEnv
Dumping ospfEnv contents...
curTime/upTime
operStatus
= 1742821s
= 1
iprmTaskStatus
iprmRegd
= 1
= 1
numAreas
= 1
numActiveAreas
numRoutes
isShuttingDown
= 1
= 148 (23)
= 0
OmniSwitch Troubleshooting Guide September 2005
page 12-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting Advanced IP Routing
Troubleshooting IP Routing
sessionId
spfCount
incrSpfCount
ageTimer
= 0
= 97
= 0
= 180
= 61
ageTicks
***Dumping myConfig contents***
cfg.flags
cfg.mcastExtensions
cfg.spfHold
= 0x223
= 0x0
= 10
cfg.spfDelay
cfg.routeTag
cfg.redistHostRoutes
routerId
= 5
= 0
= 0
= 0xa111b67
= 2
version
areaBdrRtrStatus
spfStatus
= 0
= 1
***Dumping Global spfInfo contents***
incrSpfCount
spfLast
= 0x0
= 0x18fadb
= 0x0
= 0x1388
= 0x1388
spfSignature
spfMaxNodes
incrSpfMaxNodes
.................
candidateList
pathTypeMask
intraSignature
interSignature
extSignature
startEvent
= NULL!!
= 0x0
= 0x0
= 0x0
= 0x1
= 0x0
nextEvent
= 0x0
maxNodes
= 0x0
numNodes
= 0x0
totalNodes
= 0x0
handle
= 0x0
spfRunCount
startTime
= 0x0
= 0x0
schedTime
= 0xffffffff
= 0x0
= 0x0/0x0/0x0
transAreaId
lsType/lsId/advRtr
.................
*** List/Lsdb/Rdb pointers ***
*ifList
= 0x4793410
*vlinkList
*hostList
*nbrList
*asExtLsdb
*netSum
*asbrSum
*freeExtLsaList
*freeSumLsaList
*stubAreaList
*areaList
&areaTable[]
redistProtoMask
redistTable[0] = 0x0
= 0x47a54a8
= 0x47a55b8
= 0x47a5530
= 0x4795048 (16)
= 0x4777c18
= 0x4777b90
= 0x0
= 0x0
= 0x0
= 0x47940b8
= 0x48f2cc8
= 0x2
redistTable[1] = 0x47936f0
redistTable[2] = 0x0
redistTable[3] = 0x0
redistTable[4] = 0x0
page 12-32
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Routing
Dshell Troubleshooting Advanced IP Routing
redistTable[5] = 0x0
redistTable[6] = 0x0
redistTable[7] = 0x0
*rdbRtr
*rdbNet
*rdbAsbr
= 0x47a5640
= 0x48ed4a8
= 0x47cb6a0
= 0x47adbd4
*extRdb
*** ipConfig contents ***
defaultEncap
defaultTTL
= 0
= 0
primaryAddr
= 0
defaultGwAddr
ifCfgList
rdbSyncCount
rdbSyncTimer
= 0
= 0x0
= 0
= -1
*** Fast Memory Pool Ids ***
NbrPoolId
= 0x48edbd8
RoutePoolId
= 0x48ed858
= 0x48ed818
= 0x48ed7d8
= 0x48ed678
= 0x48ed798
= 0x48ed558
= 0x48ed598
= 0x48ed4d8
= 0x48ed518
= 1744861 [0x1a9fd
LsaQueuePoolId
RdbSyncMsgPoolId
AreaAggrNodePool
AreaAggrLeafPool
RouteNodePool
RouteLeafPool
RedistNodePool
RedistLeafPool
blockResizeTimer
**** OSPF Graceful Restart Info ****
CONFIG:
restartSupport
helperSupport
= 1
= 1
helperStrictLSAChecking = 1
restartInterval
RUNNING STATE:
inRestart
= 120
= 0
= 0
inHelper
restartExitReason = 1
restartTimer = 0
restartDelayTimer = 0
value = 23 = 0x17
Working: [Kernel]->
OmniSwitch Troubleshooting Guide September 2005
page 12-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting Advanced IP Routing
Troubleshooting IP Routing
page 12-34
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
Overview
VRRP specifies an election protocol. All protocol messaging (not user data) is performed using IP multi-
cast datagrams. The Multicast IP address is 224.0.0.18. This allows VRRP to operate over a variety of
LAN technologies supporting IP. There source MAC address for these datagrams is also specified in the
RFC. That is 00-00-5E-00-01-(VRID).
The last pair in the Mac address is the Virtual Router ID (VRID). This is a configurable item. A virtual
router is defined by the VRID and a set of IP addresses. Thus a router may associate a virtual router with a
real address on an interface as well as different addresses for the virtual router and the interface. The
mapping between VRID and addresses must be coordinated among all VRRP routers on a LAN. It is
allowed reuse the same VRID with a different address mapping on a different VLAN. Each Virtual Router
is restricted to a single VLAN.
Only the Master Router for each Virtual Router sends periodic VRRP Advertisements. A back-up router
will not preempt a Master unless it has a higher priority. It is possible to preempt all preempt attempts. The
only exception is when there is a VRRP router that has the virtual router as an interface address. In that
case that router will always preempt.
After election of the Master Router, the Master Router will send VRRP Advertisements.
As long the Backup Router receives the VRRP Advertisements, it will only listen. The moment it’s not
receiving VRRP advertisements for a configured amount of time, the Backup Router will announce itself
as new Master Router in the VLAN.
In case more then one Backup Router exist, the one with the second highest priority will become Master
Router.
It should be noted that while the VRRP router must reply to ARP messages for the IP/MAC address infor-
mation it must not reply to echo request unless the virtual address is a real address on that switch.
VRRP defines three possible types of authentication. Do not mistake this authentication for access to the
network or its resources. This refers to whether or not a VRRP router will accept another VRRP routers
messages. The 3 types are None, Simple Text Password, and IP security.
page 13-2
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
Protocol Information
Protocol Information
This next section describes how VRRP routers exchange information.
IP Field Descriptions
Source Address
Destination Address
TTL
The primary address of the interface the packet is being sent from.
The IP Multicast address 224.0.0.18
Must be 255 or packet is dropped.
112 decimal.
Protocol
VRRP Field Descriptions
Version
Specifies the VRRP version of the packet. Currently this is version 2.
Type
There is only one type. 1-Advertisement. A packet set to anything other
than 1 is discarded.
VRID
The virtual Router Identifier.
Priority
Priority field can be 1-255 decimal. Higher Priorities have preference.
255 is always used by a VRRP router that uses the Virtual IP address as
a real address on an interface. Default is 100.
Count IP Address
The number of IP addresses in this advertisement.
Authentication Type
Indicates the method of authentication. As mentioned before, there are 3
types: No Authentication, Simple Text Password, IP authentications.
VRRP States
There are only 3 states that a VRRP Router can be in. They are initialize, Master, and Back-up.
OmniSwitch Troubleshooting Guide September 2005
page 13-3
Download from Www.Somanuals.com. All Manuals Search And Download.
OmniSwitch 7700/7800/8800 Implementation
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
OmniSwitch 7700/7800/8800 Implementation
This section will cover how and what the OmniSwitch 7700/7800/8800s will support.
VRRP Security
The OmniSwitch7700/7800/8800 will support no authentication and simple text password. However the
third method mentioned in the RFC, IP Authentication with HD5 HMAC is not supported in this the
current release of VRRP software.
OmniSwitch VRRP Limitations
VRRP has a 255 VRRP Instance Limit in a chassis. In addition, VRRP is done in hardware for all VRRP
IDs. However, you can only use a VRRP ID once. It cannot be reused in another VLAN. The RFC indi-
cated no limitation on reusing VRRP IDs in multiple VLANs, but OmniSwitch7700/7800/8800 does not
support this in the first release. This could cause a problem if the VRRP Partner Router is limited on the
number of Hardware Routed VRRP IDs like the OmniCore.
The OmniCore is limited to 4 VRRP IDs (0-3) because it can route in hardware only 4 Virtual MAC
addresses. These Virtual MAC addresses can be reused in separate VLANs however. When used with the
OmniSwitch7700/7800/8800 switches with the same limitations as the OmniCore will need to be the
stand-by router. If you do not design the network this way the limited VRRP Router will have to route in
software. This will slow communications and may be too much for the device to handle. For example, the
OmniCore EMM can handle only about 28 Kbps at the upper level.
page 13-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
CMM Failover
CMM Failover
When the CMM receives a Takeover message from the Chassis Supervisor it will first inform ARP to
purge all entries for the virtual router IP/Mac addresses.
VRRP will then continue with a normal start-up procedure, even though interfaces are already enabled
upon bootup of secondary. If the switch is the virtual IP address owner the switch will become the Master
and add the appropriate entries for the Virtual IP address/MAC address to the ARP table. For all other
configured virtual routers the routers will become back up.
There will be a time during a fail over that the system will not be sending VRRP advertisements. If the
failover interval exceeds the Master Timeout Interval (the timer that tells a back-up it needs to take over as
the master. Formula for this interval is found in the RFC.) The backup Router will take over as the Master.
However the ARP and HRE tables on the Network Interface (NI) cards will still contain the virtual IP/
MAC entries. As a consequence there could be a short period of time that 2 routers will be responding to
packets for the Virtual address. This will stop when VRRP is activated on the secondary CMM and the
ARP and HRE tables are cleared.
Important Information about using the CLI Command set for VRRP:
• A virtual router must be disabled before it may be modified.
• If a password is configured for VRRP authentication, the same password must be configured for all
participating VRRP routers.
• A value of 255 indicates that the VRRP router owns the IP address, that is, that the router contains the
real physical interface to which the IP address is assigned. The system automatically sets this value to
255 if it detects that this router is the IP address owner. The IP address owner will always be the master
router if it is available.
• VRRP routers backing up a virtual router must use priority values from 1 to 254. The default priority
value for VRRP routers backing up a virtual router is 100. If you configure more than one backup, their
priority values should be different. Preempt and no preempt settings specifies whether or not a higher
priority router may preempt a lower priority router.
• The system sets the priority value to zero in the last VRRP advertisement packet before a master router
is shut down (when a router is added or deleted to the configuration).
OmniSwitch Troubleshooting Guide September 2005
page 13-5
Download from Www.Somanuals.com. All Manuals Search And Download.
CMM Failover
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
show vrrp statistics
Displays statistics about VRRP packets for all virtual routers configured on the switch or for a particular
virtual router.
show vrrp [vrid] statistics
Syntax Definitions
vrid
The virtual router ID, in the range from 1–255 (OmniSwitch 7700,
7800, or 8800) or 1–7 (OmniSwitch 6624 or 6648).
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
Use the show vrrp statistics command to display information about VRRP packets. Use the show vrrp
command to display information about the virtual router configuration.
Examples
-> show vrrp statistics
Checksum
Errors
Version
Errors
VRID
Errors
----------+-----------+---------
0
0
0
VRID VLAN State
UpTime Become Master Adv. Rcvd
----+ ----+ -------------+----------+--------------+------------
1
2
7
1 master
15 backup
2 initialize
378890
4483
0
1
0
0
0
64783
0
output definitions
Checksum Errors
The total number of VRRP packets received with an invalid checksum
value.
Version Errors
VRID Errors
The total number of VRRP packets received with an invalid version
number.
The total number of VRRP packets received with an invalid VRID for
this virtual router.
VRID
The virtual router identifier.
VLAN
The VLAN associated with the VRRP instance.
page 13-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
CMM Failover
output definitions (continued)
State
The administrative state of the VRRP instance; initialize means that
this VRRP instance is waiting for a startup event, such as a reboot or
when the virtual router is disabled; backup means that this instance is
monitoring the availability and the state of the master router; master
means that this instance is functioning as the master router.
UpTime
Time interval (in hundredths of a second) since this virtual router was
last initialized.
Become Master
The total number of times this virtual router’s state has transitioned
from backup to master.
Adv. Rcvd
The total number of VRRP advertisements received by this instance.
-> show vrrp 1 statistics
Virtual Router VRID = 1 on VLAN = 1
State
= master
= 378890
= 1
UpTime (1/100th second)
Become master
Advertisement interval errors
Password errors
= 0
= 0
Authentication errors
Authentication type errors
IP TTL errors
= 0
= 0
= 0
IP address list errors
Zero priority advertisements sent
= 0
= 0
Zero priority advertisements received = 0
output definitions
VRID
VLAN
State
The virtual router identifier.
The VLAN associated with the VRRP instance.
The administrative state of the VRRP instance; initialize means that
this VRRP instance is waiting for a startup event, such as a reboot or
adding a new virtual router to the configuration; backup means that
this instance is monitoring the availability and the state of the master
router; master means that this instance is functioning as the master
router.
UpTime
Time interval (in hundredths of a second) since this virtual router was
last initialized.
Become master
The total number of times this virtual router’s state has transitioned
from backup to master.
Advertisements received
Type errors
The total number of VRRP advertisements received by this instance.
The total number of VRRP packets received with an invalid value in
the VRRP type field.
Advertisement interval errors The total number of VRRP packets received in which the advertisement
interval was different than the one configured for the virtual router.
Password errors
The total number of VRRP packets received that did not pass the sim-
ple text password authentication check.
Authentication errors
The total number of VRRP packets received with an unknown or
invalid authentication type.
OmniSwitch Troubleshooting Guide September 2005
page 13-7
Download from Www.Somanuals.com. All Manuals Search And Download.
CMM Failover
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
output definitions (continued)
Authentication type errors
The total number of VRRP packets received in which the AuthType
value was different than the one configured for the virtual router.
IP TTL errors
The total number of VRRP packets received in which the IP address list
does not match the configured list for the virtual router.
IP address list errors
The total number of VRRP packets in which the IP address list does not
match the configured list for the virtual router.
Zero priority advertisements
sent
The total number of VRRP advertisements with a priority of 0 sent by
the virtual router.
Zero priority advertisements
received
The total number of VRRP advertisements with a priority of 0 received
by the virtual router.
Release History
Release 5.1; command was introduced.
page 13-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
OmniSwitch VRRP Troubleshooting
OmniSwitch VRRP Troubleshooting
The following commands can be used to troubleshoot VRRP:
swlog appid vrrp level debug3
Example output:
sw-2> swlog appid vrrp level debug3
+++ vrrpAdverTimer
+++ vrrpSendAdvPkt: vrid=1 pri0=0
+++ vrrpSendAdvPkt: VRID 10 (0xa) sent 20 bytes
+++ vrrpAdverTimer
+++ vrrpSendAdvPkt: vrid=1 pri0=0
+++ vrrpSendAdvPkt: VRID 10 (0xa) sent 20 bytes
+++ vrrpAdverTimer
+++ vrrpSendAdvPkt: vrid=1 pri0=0
+++ vrrpSendAdvPkt: VRID 10 (0xa) sent 20 bytes
debug ip packet protocol num 112 start timeout 30
Example output:
C S 1/F 00005e00010b->01005e000012 IP 192.168.101.254->224.0.0.18 VRRP
C S 1/F 00005e00010c->01005e000012 IP 192.168.102.254->224.0.0.18 VRRP
1 R CMM (00005e00010a)->01005e000012 IP 192.168.100.254->224.0.0.18 VRRP 33,10
1 S IPM 00005e00010a->01005e000012 IP 192.168.100.254->224.0.0.18 VRRP 33,10
1 R CMM (00005e00010b)->01005e000012 IP 192.168.101.254->224.0.0.18 VRRP 33,11
1 S IPM 00005e00010b->01005e000012 IP 192.168.101.254->224.0.0.18 VRRP 33,11
1 R CMM (00005e00010c)->01005e000012 IP 192.168.102.254->224.0.0.18 VRRP 33,12
Other things to check in case of problems:
• Use a sniffer to see if packets are send by the master VRRP router and received at the backup VRRP
routers.
• If two VRRP routers both believe that they are the masters and you have check the cabling and the port
membership of the VLAN the VRRP instance is in then it is possible that there is a disagreement in
one or more of the VRRP configured parameters. The show vrrp vrrpid statistics command will show
you if you are receiving advertisements from the other VRRP Routers and if those advertisements are
being dropped because of an error in the packet. Here is an example of the output.
OmniSwitch Troubleshooting Guide September 2005
page 13-9
Download from Www.Somanuals.com. All Manuals Search And Download.
ARP Table
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
ARP Table
The ARP Table of the OmniSwitch that is the Master Router will have the Virtual MAC Learned in the
ARP Table. It will not be learned on a port. In the example below I use the show arp command to illus-
trate before and after a switch the VRRP master.
-> show arp
Total 3 arp entries
Flags (P=Proxy, A=Authentication, V=VRRP)
IP Addr
Hardware Addr
Type
Flags Port
Interface
-----------------+-------------------+----------+-------+--------+----------
172.50.1.254
172.51.1.254
172.52.1.254
00:00:5e:00:01:32 STATIC
00:00:5e:00:01:33 STATIC
00:00:5e:00:01:34 STATIC
PV
PV
PV
UNKNOWN vlan 500
UNKNOWN vlan 501
UNKNOWN vlan 502
-----------------+-------------------+----------+-------+--------+----------
-> vrrp 1 2 disable
SUN FEB 19 23:05:28 : VRRP (77) info message : Virtual router VRID=1 VLAN=2 state
is initialize
-> SUN FEB 19 23:05:28 : VRRP (77) info message : Virtual router VRID=1 VLAN=2
disabled
vrrp 1 2 priority 110
-> vrrp 1 2 enable
SUN FEB 19 23:05:41 : VRRP (77) info message : Virtual router VRID=1 VLAN=2 enabled
-> SUN FEB 19 23:05:42 : VRRP (77) info message : Virtual router VRID=1 VLAN=2
state is backup
SUN FEB 19 23:05:46 : VRRP (77) info message : Virtual router VRID=1 VLAN=2 state
is master
Total 1 arp entries
Flags (P=Proxy, A=Authentication, V=VRRP)
IP Addr
-----------------+-------------------+----------+-------+--------+----------
10.1.96.5 00:50:04:b2:c9:ee STATIC PV UNKNOWN vlan 2
Hardware Addr
Type
Flags Port
Interface
page 13-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
Dshell Troubleshooting
Dshell Troubleshooting
In a situation where VRRP is flapping, go into Dshell of the switch that is configured as the backup virtual
router that is flapping and enter vrrpTMon(1, vrid, vlanId). For example, for virtual router 200 on VLAN
200 the command will be: vrrpTMon(1,200,200). You should then see the advertisements arriving once
per second on your console. Before running Dshell commands make sure to verify the configuration of all
VRRP participated switches.
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
7800-1 -> dshell
Working: [Kernel]->vrrpTMon (1,200,200)
vrrpDbg = 00000010 vrrpDbgVR = 00C800C8
value = 1 = 0x1
Working: [Kernel]->
I 54758886 VRID 200 VLAN 200
4500 0014 0DC3 0000 FF70 0000 ACC8 011C
E000 0012 21C8 FF01 0001 3150 ACC8 011C
0000 0000 0000 0000
I 54758986 VRID 200 VLAN 200
4500 0014 7449 0000 FF70 0000 ACC8 011C
E000 0012 21C8 FF01 0001 3150 ACC8 011C
0000 0000 0000 0000
I 54759086 VRID 200 VLAN 200
4500 0014 E847 0000 FF70 0000 ACC8 011C
E000 0012 21C8 FF01 0001 3150 ACC8 011C
0000 0000 0000 0000
Watch for the sequence number increasing. This indicates 3 hello packets received in 3 seconds.
Disable this Dshell command by setting value 0.
Working: [Kernel]->vrrpTMon 0
OmniSwitch Troubleshooting Guide September 2005
page 13-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting Virtual Router Redundancy Protocol (VRRP)
page 13-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
14 Troubleshooting IP
Multicast Switching (IPMS)
In order to troubleshoot IP Multicast Switching, a basic understanding of its function is required. Some
basic concepts are covered below. OmniSwitch 7700/7800/8800 supports IP Multicast Switching and
Routing.
Reading the “Configuring IP Multicast Switching” chapter in the appropriate OmniSwitch Network
Configuration Guide is also highly recommended.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 14-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Troubleshooting a Device that Cannot Join an IP Multicast Stream
Troubleshooting a Device that Cannot Join an IP
Multicast Stream
If a device cannot join a stream, the first thing to do is to verify Layer 2/Layer 3 connectivity and that no
physical errors exist. The next step is to look at the switch the device is attache to, see if the device is a
member of the multicast group. This is done by issuing the show ip multicast groups command:
-> show ip multicast groups
Destination IP
Source IP
VLAN Slot/Port Expire
--------------------+--------------------+----+---------+------
224.0.0.9
224.0.1.22
224.0.1.24
239.255.255.250
239.255.255.250
239.255.255.254
239.255.255.254
10.10.10.50
10.10.10.65
10.10.10.5
10.10.10.50
10.10.10.66
10.10.10.5
10.10.10.70
1
1
1
1
1
1
1
5/23
5/23
5/23
5/23
5/23
5/23
5/23
250
249
247
244
140
251
137
Note. Complete details of the output of this and other IP Multicast commands can be obtained from the
“IP Multicast Switching” chapter in the appropriate OmniSwitch CLI Reference Guide.
This will show a listing of the multicast groups currently known by this switch, listing the IP address of
the stream (Destination IP), and the source of the IGMP join message (Source IP, in this instance the
“client”). If the switch has seen an IGMP message it will add the client to this list, you can verify the slot
and port from the table. The above example shows the multicast streams available on the switch, which is
connected via slot 5 port 23. In the next example, a client (10.10.10.64) has join a VLAN 1 multicast
stream:
-> show ip multicast groups
Destination IP
Source IP
VLAN Slot/Port Expire
--------------------+--------------------+----+---------+------
224.0.0.9
224.0.1.22
224.0.1.24
224.77.1.0
224.77.205.58
239.255.255.250
239.255.255.254
10.10.10.50
10.10.10.65
10.10.10.5
10.10.10.64
10.10.10.64
10.10.10.50
10.10.10.70
1
1
1
1
1
1
1
5/23
5/23
5/23
5/15
5/15
5/23
5/23
192
191
195
217
221
196
191
This shows a functional stream is now being sent to slot 5 port 15, and gives the multicast stream’s IP
address(es). The expiry timer shows the number of seconds left before the particular stream times out on
the slot/port if an IGMP message is not received. When the switch receives an IGMP message it will reset
the timer to 260 seconds; this process repeats until the station leaves the stream, or the stream itself fails
for some reason.
If your device cannot join a stream, you will not see it in the list. The next step to take is to repeat the
show ip multicast groups command on the next switch in line between the end station and the stream
source until you find out where the stream fails. You will find a point where a stream exists on one switch,
but not on the next one in line to the destination. The task then becomes configuring those units to prop-
erly pass IP Multicast traffic (see the “Configuring IP Multicast” chapter in the appropriate OmniSwitch
Network Configuration Guide.
OmniSwitch Troubleshooting Guide September 2005
page 14-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Troubleshooting a Device that Drops Out of an IP Multicast Stream
Troubleshooting a Device that Drops Out of an IP
Multicast Stream
If the issue is a device can actually join a multicast stream, but loses it after a period of time, there are a
few items to check. First, does the device lose the stream when the Expiry timer reaches zero in the show
ip multicast groups command?
-> show ip multicast groups
Destination IP
Source IP
VLAN Slot/Port Expire
--------------------+--------------------+----+---------+------
224.0.0.9
224.0.1.22
224.0.1.24
224.77.1.0
224.77.205.58
239.255.255.250
239.255.255.254
239.255.255.254
10.10.10.50
10.10.10.65
10.10.10.5
10.10.10.64
10.10.10.64
10.10.10.66
10.10.10.5
10.10.10.70
1
1
1
1
1
1
1
1
5/23
5/23
5/23
5/15
5/15
5/23
5/23
5/23
242
239
235
235
234
236
235
260
Once this timer reaches zero, the switch will stop sending the multicast stream to this port, as it believes
there are no longer any devices requesting it. This could happen if in the VLAN where the device
connects, an IP multicast router does not exist. The multicast client will send IGMP messages on layer 3,
and if the VLAN has no L3 instance, there is no way for it to listen to those messages. It is then recom-
mended to have at least one IP multicast router configured and enabled on the VLAN.
Issue a show vlan command to check the configuration of the VLAN. For example:
-> show vlan 1
Name
: VLAN 1,
Administrative State: enabled,
Operational State : disabled,
Spanning Tree State : enabled,
Authentication
IP Router Port
IPX Router Port
: disabled,
: none,
: none
Assign the VLAN an IP address that is proper for your network:
-> vlan 1 router ip 10.10.10.7 mask 255.255.255.0
Then reissue the show vlan command to verify:
-> show vlan 1
Name
: VLAN 1,
Administrative State: enabled,
Operational State : disabled,
Spanning Tree State : enabled,
Authentication
IP Router Port
IPX Router Port
: disabled,
: 10.10.10.7 255.255.255.0 forward e2,
: none
Now that an IP address has been assigned, recheck the show ip multicast groups command and verify
that the slot/port in question has an entry. You should see the timer decrement and reset as described
above.
OmniSwitch Troubleshooting Guide September 2005
page 14-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Troubleshooting a Device that Drops Out of an IP Multicast Stream
Is Multicast Switching enabled on your switch? If it is not enabled, you will likely notice high utilization
for the switch, and devices in the VLANs where multicast traffic is flowing will be being flooded with the
stream(s). As Multicast Switching comes standard with this release, it should be enabled.
Use the show ip multicast switching command to display the current IPMS configuration on a switch.
If it is not enabled, you will see:
-> show ip multicast switching
IPMS Configuration
IPMS State:
Hardware Routing:
Priority:
Disabled,
Disabled,
high,
Max Ingress Bandwidth: 10,
Leave Timeout:
1,
Membership Timeout:
Neighbor Timeout:
Querier Timeout:
Query Interval:
260,
90,
260,
125
To enable it, enter:
-> ip multicast switching
Then the show ip multicast switching command will show:
-> show ip multicast switching
IPMS Configuration
IPMS State:
Hardware Routing:
Priority:
Enabled,
Disabled,
high,
Max Ingress Bandwidth: 10,
Leave Timeout:
1,
Membership Timeout:
Neighbor Timeout:
Querier Timeout:
Query Interval:
260,
90,
260,
125
With the presence of multicast router on the network, you need to see if IP Multicast enabled switch has
this router listed as a multicast neighbor. In addition, one multicast querier should exist per network, this
querier corresponds to the one switch or router participant of the multicast domain with the lowest IP
address.
-> show ip multicast neighbors
Source IP
--------------------+----+---------+------+-------
10.10.10.187 4/5 NeverStatic
VLAN Slot/Port Expire Type
5
The above example has a static-neighbor configured. A static-neighbor is a port configured to receive all
multicast streams on a VLAN, as well as to receive all IGMP reports for the VLAN.
If you do not see the neighbor switch in the output, as a work around you may want to add it as a Static
Neighbor and verify connectivity. See the “Configuring a Static Neighbor” section in the appropriate
OmniSwitch Troubleshooting Guide September 2005
page 14-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Troubleshooting a Device that Drops Out of an IP Multicast Stream
OmniSwitch Network Configuration Guide. Also, see the “IPMS Application Example” section as it gives
a good example of how and when to use several of the IPMS commands.
To find where a multicast stream begins in your network, you can use the show ip multicast forwarding
command. This is similar to the show ip multicast groups command, but notice that “Source IP” in this
command differs in that this states the entry point of the stream (server), whereas the show ip multicast
group command displays the source IP of the IGMP join message (client). The slot/port output also gives
you the “trail” to follow in tracking down the source of the multicast stream/server.
-> show ip multicast forwarding
Source
Type VLAN Slot/Port Type VLAN Slot/Port
-------------------+-------------------+----+----+---------+----+----+---------
Destination
Multicast Group
Source IP
224.77.1.0
224.77.205.58
10.10.10.68 NATV
10.10.10.68 NATV
1
1
5/13 NATV
5/13 NATV
1
1
5/15
5/15
Is your switch set up so that there are policies preventing multicast traffic from entering or leaving a
particular VLAN? Use the show ip multicast policy-cache command to check:
-> show ip multicast policy-cache
Policy Group Address
Src Address
Vlan Port Disp Time
-------+----------------+----------------+------+------+------+------
MBR
MBR
MBR
MBR
MBR
MBR
MBR
MBR
MBR
224.0.0.9
10.10.10.50
10.10.10.65
10.10.10.5
10.10.10.68
10.10.10.64
10.10.10.64
1
1
1
1
1
1
1
1
1
5/23 ACPT 133
5/23 ACPT 132
5/23 ACPT 136
5/13 ACPT 138
5/15 ACPT 259
5/15 ACPT 258
5/23 ACPT 137
5/23 ACPT 258
5/23 ACPT 259
224.0.1.22
224.0.1.24
224.77.0.0
224.77.1.0
224.77.205.58
239.255.255.250 10.10.10.50
239.255.255.250 10.10.10.66
239.255.255.254 10.10.10.70
The “DISP” column should display ACPT for “Accept.”
IPMS follows the IGMP V2 specification, which means that the queriers are elected based on the switch/
router with the lowest IP address. During startup, all switches will be listed because they all send initial
IGMP queries. After the official querier is elected, the other switches will stop flooding IGMP queries of
their own. Eventually, only one querier in the network will remain, and will be the only one listed in the
show ip multicast queriers command for all switches in the VLAN. The querier periodically sends a
Membership Query message to the all-systems group (224.0.0.1). The hosts then respond with a host
membership report message to the group address for the stream(s) they want to receive. The querier
receives the message, and adds the group to its’ membership list.
-> show ip multicast queriers
Source IP
--------------------+----+---------+------+-------
10.10.10.190 5/1 167 Dynamic
VLAN Slot/Port Expire Type
1
Type of “Dynamic” means that the IP address was learned via IGMP messages, so the address should be
alive and functioning; it is worth verifying that you can ping the addresses along your path, however.
OmniSwitch Troubleshooting Guide September 2005
page 14-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Troubleshooting a Device that Drops Out of an IP Multicast Stream
You may also have a misconfigured or malfunctioning ip multicast static-querier. In the show ip
multicast queriers command, look for Type of “Static” and check to see if the IP addresses configured
exist and are functioning properly.
Also mentioned was that if a group membership expires it may be because it isn’t on an IP VLAN. This is
probably due to a querying problem. IPMS cannot send IGMP queries on a VLAN that doesn’t have an IP
address, but you can still have another switch in the same VLAN that is configured for IP and is querying.
In this case, things will work because there is still a querier present, even if it is not a local switch.
Remember that queriers are required for the re-solicitation of IGMP clients. Queries are sent every 120
seconds, to which all clients must respond with a membership report.
Also check the flood limits (show interfaces flood rate) to see if the switch is dropping packets due to
them being over the limit:
You want to see Flood only in an IPMS environment. If you see:
-> show interfaces flood rate
Slot/Port peak rate(Mb/second) Enable
-----------+----------------------+---------------
4/1
4/2
4/3
47
47
47
Flood/multicast
Flood/multicast
Flood/multicast
You will want to set it back to Flood only via:
-> interfaces 4 flood
Note that this is by slot, not by VLAN.
OmniSwitch Troubleshooting Guide September 2005
page 14-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Troubleshooting IPMS in Debug CLI
Troubleshooting IPMS in Debug CLI
The Debug CLI will allow you to view traffic traversing the switch in many ways. The most useful
command for troubleshooting IP Multicast is:
-> debug ip packet show-multicast on board ni 1 output console
This command turns on debug for IP packets, turns on the ability to show multicast packets, looks only on
blade #1, and outputs to console. The output is:
-> 1 R IPM 00d095206406->(01005e000001) IP 10.10.10.190->224.0.0.1 IGMPv2 MQ
1 S CMM 00d095206406->01005e000001 IP 10.10.10.190->224.0.0.1 IGMPv2 MQ
1 R IPM 00a0c955af3e->(01005e4d0100) IP 10.10.10.51->224.77.1.0 IGMPv2 MR
1 S CMM 00a0c955af3e->01005e4d0100 IP 10.10.10.51->224.77.1.0 IGMPv2 MR
1 R IPM 00c04f0c3b2d->(01005e7ffffe) IP 10.10.10.5->239.255.255.254 IGMPv2 MR
1 S CMM 00c04f0c3b2d->01005e7ffffe IP 10.10.10.5->239.255.255.254 IGMPv2 MR
1 R IPM 00c04f0c3b2d->(01005e7ffffe) IP 10.10.10.5->239.255.255.254 IGMPv2 MR
1 S CMM 00c04f0c3b2d->01005e7ffffe IP 10.10.10.5->239.255.255.254 IGMPv2 MR
1 R IPM 0060971c0c45->(01005e000009) IP 10.10.10.220->224.0.0.9 IGMPv2 MR
1 S CMM 0060971c0c45->01005e000009 IP 10.10.10.220->224.0.0.9 IGMPv2 MR
1 R IPM 0008c709f671->(01005e3796d0) IP 10.10.10.222->229.55.150.208 IGMPv2 MR
1 S CMM 0008c709f671->01005e3796d0 IP 10.10.10.222->229.55.150.208 IGMPv2 MR
1 R IPM 0008c709f671->(01005e3796d0) IP 10.10.10.222->229.55.150.208 IGMPv2 MR
1 S CMM 0008c709f671->01005e3796d0 IP 10.10.10.222->229.55.150.208 IGMPv2 MR
1 R IPM 00d095265480->(01005e000004) IP 10.10.10.34->224.0.0.4 IGMPv1 DV RSP
1 S CMM 00d095265480->01005e000004 IP 10.10.10.34->224.0.0.4 IGMPv1 DV RSP
1 R IPM 00a0c955af3e->(01005e4db6d6) IP 10.10.10.51->224.77.182.214 IGMPv2 MR
1 S CMM 00a0c955af3e->01005e4db6d6 IP 10.10.10.51->224.77.182.214 IGMPv2 MR
1 R IPM 0008c709f671->(01005e000118) IP 10.10.10.222->224.0.1.24 IGMPv2 MR
1 S CMM 0008c709f671->01005e000118 IP 10.10.10.222->224.0.1.24 IGMPv2 MR
1 R IPM 0008c709f671->(01005e000118) IP 10.10.10.222->224.0.1.24 IGMPv2 MR
1 S CMM 0008c709f671->01005e000118 IP 10.10.10.222->224.0.1.24 IGMPv2 MR
1 R IPM 0010a4c59c87->(01005e000116) IP 10.10.10.54->224.0.1.22 IGMPv2 MR
1 S CMM 0010a4c59c87->01005e000116 IP 10.10.10.54->224.0.1.22 IGMPv2 MR
1 R IPM 0010a4c59c87->(01005e000116) IP 10.10.10.54->224.0.1.22 IGMPv2 MR
1 S CMM 0010a4c59c87->01005e000116 IP 10.10.10.54->224.0.1.22 IGMPv2 MR
For this example, Ghost was used to multicast to a client as follows: Ghost server at 10.10.10.222,
connected to an OSR9, which was uplinked to a Falcon 7700 via 10/100 Ethernet on 1/22; the Ghost
multicast client was at 10.10.10.51 on 1/7. From the output, we can see that the client is receiving a stream
with multicast address 224.77.182.214, which matches with the output of the show ip multicast
forwarding command:
-> show ip multicast forwarding
Source
Type VLAN Slot/Port Type VLAN Slot/Port
-------------------+-------------------+----+----+---------+----+----+---------
Destination
Multicast Group
Source IP
224.77.182.214
10.10.10.222 NATV
1
1/22 NATV
1
1/7
Showing the IP address of the source of the actual stream as 10.10.10.222.
OmniSwitch Troubleshooting Guide September 2005
page 14-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Troubleshooting IPMS in Debug CLI
Note the output of the show ip multicast queriers command during this test:
-> show ip multicast queriers
Source IP
--------------------+----+---------+------+-------
10.10.10.190 1/22 146 Dynamic
VLAN Slot/Port Expire Type
1
The .190 address is that of the uplinked OSR9 in the test.
The show ip multicast neighbors command will show the neighbors in this test network:
-> show ip multicast neighbors
Source IP
--------------------+----+---------+------+-------
10.10.10.34 1/22 85 Dynamic
VLAN Slot/Port Expire Type
1
It is actually unrelated to the test, other than it being in the test network while testing was being done. It is
worthwhile to note that there is a neighbor being listed, and that it, too, was learned from port 1/22, the
uplink port to the OSR9.
The show ip multicast groups command during the test:
-> show ip multicast groups
Destination IP
Source IP
VLAN Slot/Port Expire
--------------------+--------------------+----+---------+------
224.0.0.9
224.0.1.22
224.0.1.24
224.77.1.0
224.77.182.214
229.55.150.208
239.255.255.254
239.255.255.254
10.10.10.220
10.10.10.54
10.10.10.222
10.10.10.51
10.10.10.51
10.10.10.222
10.10.10.5
1
1
1
1
1
1
1
1
1/22
1/22
1/22
1/7
157
210
210
156
162
210
210
85
1/7
1/22
1/22
1/22
10.10.10.222
You can match the groups to the associated IP addresses from the above debug command to verify that all
is functioning properly.
Note for the debug CLI command:
The command
-> debug ip packet show-multicast on board ni 1 output console
will only set the options for debug. In order to actually see the output, you must enter:
-> debug ip packet start
And to stop the output:
-> debug ip packet stop
Another tip is to enter the full debug ip packet command, then enter debug ip packet stop, to which you
will get a response “...already stopped,” and then enter debug ip packet start. That way, in order to stop the
display, you can simply up-arrow twice and hit enter to stop the display, which will likely be scrolling by
quickly enough so that you cannot see what you are entering!
OmniSwitch Troubleshooting Guide September 2005
page 14-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
Dshell Troubleshooting
The IPMS application has its own shell to verify the specific data displayed on the CLI. Use a question
mark to display the local list of commands for each level. Every CLI commend has a corresponding output
on this shell with extended information on each entry. See examples below:
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
Certified: [Kernel]->ipmsdbg_shell
IPMS Debug Session
type '~' to quit session
MAIN> ?
Main Menu
main
- Main Menu
clist - Display Sub-tasks
restart - Restart IPMS
MAIN> clist
Connected Tasks
ipmem
ipmfm
ipmni1 [slot/slice 1/0] [chipset C1] [ONLINE] []
ipmni2 [slot/slice 8/0] [chipset C1] [ONLINE] []
ipmni3 [slot/slice 9/0] [chipset C2] [ONLINE] []
ipmni4 [slot/slice 16/0] [chipset C1] [ONLINE] []
ipmni5 [slot/slice 2/0] [chipset C1] [ONLINE] []
ipmni6 [slot/slice 7/0] [chipset C1] [ONLINE] []
ipmni7 [slot/slice 10/0] [chipset C1] [ONLINE] []
ipmni8 [slot/slice 15/0] [chipset C1] [ONLINE] []
ipmni9 [slot/slice 6/0] [chipset C1] [ONLINE] []
ipmni10 [slot/slice 3/0] [chipset C1] [ONLINE] []
ipmni11 [slot/slice 11/0] [chipset C1] [ONLINE] []
ipmni12 [slot/slice 14/0] [chipset C2] [ONLINE] []
ipmni13 [slot/slice 4/0] [chipset C1] [ONLINE] []
ipmni14 [slot/slice 5/0] [chipset C2] [ONLINE] []
ipmni15 [slot/slice 12/0] [chipset C1] [ONLINE] []
ipmni16 [slot/slice 13/0] [chipset C2] [ONLINE] []
MAIN> ipmem
IPMEM> ?
Current State:
Enabled
Hardware Routing: Enabled
Priority:
0
Max Bandwidth:
10
RP Rate Threshold: 65536
PIM CKSUM mode:
Header Only
Available Commands:
OmniSwitch Troubleshooting Guide September 2005
page 14-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
grp - Group Membership
nbr - Neighbors
qry - Queriers
src - Sources
prx - Proxy
vprx - Proxy by Vlan
v3prx - IGMPv3 Proxies
qint - Querier interface list
qtmr - Querier timer list
hwrt - Toggle hardware flag
enbl - Toggle enable flag
IPMEM> grp
Hash
IDX
Destination IP
Source MAC
Client IP
VLAN VPN EXP TYP Mode Version Flags
==== =================== =================== ==== === ===== === ==== ======= =====
0001 239.1.1.1
0014 00b0d0:43d3f5
0022 224.0.1.22
0001 0000c0:4affec
0024 224.0.1.24
0001 0000c0:4affec
0090 239.0.0.90
0001 0000c0:4affec
0101 239.1.1.101
0014 00b0d0:43d3f5
0254 239.255.255.254
0001 0000c0:4affec
172.50.255.23
172.99.255.153
172.99.255.153
172.99.255.153
172.50.255.23
172.99.255.153
0500 128 241 NAT Excl 2
0549 012 243 NAT Excl 2
0549 012 247 NAT Excl 2
0549 012 244 NAT Excl 2
0500 128 245 NAT Excl 2
0549 012 247 NAT Excl 2
00000
00000
00000
00000
00000
00000
IPMEM> nbr
Hash
Source IP
VLAN VPN EXP TYP ID FLAGS
==== ==================== ==== === === === ==== =====
0000
0001
172.62.1.28 512 128 90 NAT 0014 00000
172.63.1.28 513 128 90 NAT 0014 00000
[ Deleted lines to reduce size]
0062
0063
172.60.1.28 510 128 90 NAT 0014 00000
172.61.1.28 511 128 90 NAT 0014 00000
IPMEM> qry
Hash
Source IP
VLAN VPN EXP TYP ID FLAGS
==== ==================== ==== ==== ==== === === =====
0000
0001
172.62.1.23 512 128 204 NAT 14 00000
172.63.1.23 513 128 204 NAT 14 00000
[ Deleted lines to reduce size]
0062
0063
172.60.1.23 510 128 204 NAT 14 00000
172.61.1.23 511 128 204 NAT 14 00000
OmniSwitch Troubleshooting Guide September 2005
page 14-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
IPMEM> src
Hash Multicast Source IP/ Multicast Dest IP VLAN VPN TYP EXP RTY Pkt Cnt
INDX Unicast Source IP
==== ==================== ==================== ==== === === === === =======
0291
0001
172.99.255.153
0.0.0.0
239.1.1.101 549 12 NAT -63009 0
0
IPMEM> qint
VLAN
Intf Addr/
MAC
ACT State Version Nbr V1 Port Timeout
Querier Addr
-------- -------------------- ------------- --- ----- ------- --- ------- -------
0100
0200
0500
172.100.1.25 000001:005e00 1 Self
172.100.1.25
172.200.1.25 ac4401:1ce000 1 Self
172.200.1.25
172.50.1.25 000001:000000 1 Other
172.50.1.23
3 0
3 0
3 0
…[ Deleted lines to reduce size]....
172.97.1.23
0548
0549
172.98.1.25 000000:000000 1 Other
172.98.1.23
172.99.1.25 000000:000000 1 Other
172.99.1.23
3 0
3 0
IPMEM> qtmr
Last Total Total
Expire VLAN Change Joins Groups
--------- ---- ------ ----- ------
00000089 0200 63060 0000 0000
00000089 0100 63060 0000 0000
00000255 0522 62902 0000 0000
….[ Deleted lines to reduce size]...
00000255 0502 62902 0000 0000
00000255 0500 62902 0000 0000
IPMEM> v3prx
Group Address
VLAN Mode
Source IP
Mode Port Time Client IP
==================== ==== ==== ==================== ==== ==== ==== ================
239.255.255.254
224.0.1.22
224.0.1.24
239.1.1.101
239.0.0.90
239.1.1.1
0549 Excl
0549 Excl
0549 Excl
0500 Excl
0549 Excl
0500 Excl
0012 0254
0012 0256
0012 0256
0128 0237
0012 0238
0128 0256
172.99.255.153
172.99.255.153
172.99.255.153
172.50.255.23
172.99.255.153
172.50.255.23
OmniSwitch Troubleshooting Guide September 2005
page 14-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
MAIN> ?
Main Menu
main
- Main Menu
clist - Display Sub-tasks
restart - Restart IPMS
MAIN> clist
Connected Tasks
ipmem
ipmfm
ipmni1 [slot/slice 1/0] [chipset C1] [ONLINE] []
ipmni2 [slot/slice 8/0] [chipset C1] [ONLINE] []
ipmni3 [slot/slice 9/0] [chipset C2] [ONLINE] []
ipmni4 [slot/slice 16/0] [chipset C1] [ONLINE] []
ipmni5 [slot/slice 2/0] [chipset C1] [ONLINE] []
ipmni6 [slot/slice 7/0] [chipset C1] [ONLINE] []
ipmni7 [slot/slice 10/0] [chipset C1] [ONLINE] []
ipmni8 [slot/slice 15/0] [chipset C1] [ONLINE] []
ipmni9 [slot/slice 6/0] [chipset C1] [ONLINE] []
ipmni10 [slot/slice 3/0] [chipset C1] [ONLINE] []
ipmni11 [slot/slice 11/0] [chipset C1] [ONLINE] []
ipmni12 [slot/slice 14/0] [chipset C2] [ONLINE] []
ipmni13 [slot/slice 4/0] [chipset C1] [ONLINE] []
ipmni14 [slot/slice 5/0] [chipset C2] [ONLINE] []
ipmni15 [slot/slice 12/0] [chipset C1] [ONLINE] []
ipmni16 [slot/slice 13/0] [chipset C2] [ONLINE] []
MAIN> ipmfm
IPMFM> ?
IPMFM State: Enabled
Hardware Routing: Enabled
Available Commands:
fwd - IPMFM Forwarding Table
dst - IPMFM Destination Table
task - IPMFM Display connections
dgid - IPMFM DGID usage
rtvl - IPMFM Router MAC VLAN Table
IPMFM> fwd
Hsh/ Multicast Dest IP/
Source IP
Tunnel Source IP DTYPE DVLN TTTL
PRNT TTL CGRP VFLG DVPN DVCI DFLG
STYPE SVLN SVPN SVCI
ID
Tunnel Dest IP/
Router MAC Address
==== ==================== ==================== ===== ==== ==== ==== ==== ==== ====
0291
0001
239.1.1.101
0.0.0.0
172.99.255.153 NATV 0549 0012 0000
0.0.0.0 NATV 0549 0000
00:00:00:00:00:00
0000 0000 3078 0004
0128 0000 0013
0128 0000
OmniSwitch Troubleshooting Guide September 2005
page 14-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
IPMFM> dst
HASH
Destination IP
VLAN VPN VCI
TYPE
ID
==== ==================== ==== === ==== ========== ====
0000
0.0.0.0 0526 128 0000
0534 128 0000
NATV 0014 0001
NATV 0014 0001
NATV 0014 0001
0535 128 0000
….[ Deleted lines to reduce size]....
0532 128 0000
0508 128 0000
0527 128 0000
NATV 0014 0001
NATV 0014 0001
NATV 0014 0001
NATV 0001 0001
NATV 0014 0001
NATV 0001 0001
NATV 0001 0001
NATV 0014 0001
NATV 0001 0001
0090
0257
0278
0280
0357
0510
239.0.0.90 0549 012 0000
239.1.1.1 0500 128 0000
224.0.1.22 0549 012 0000
224.0.1.24 0549 012 0000
239.1.1.101 0500 128 0000
239.255.255.254 0549 012 0000
IPMFM> task
ipmfm
ipmni1 [ipmem id 1] [NP Not Present] [CORO 1]
ipmni2 [ipmem id 2] [NP Not Present] [CORO 1]
ipmni3 [ipmem id 3] [NP Not Present] [CORO 2]
ipmni4 [ipmem id 4] [NP Not Present] [CORO 1]
ipmni5 [ipmem id 5] [NP Not Present] [CORO 1]
ipmni6 [ipmem id 6] [NP Not Present] [CORO 1]
ipmni7 [ipmem id 7] [NP Not Present] [CORO 1]
ipmni8 [ipmem id 8] [NP Not Present] [CORO 1]
ipmni9 [ipmem id 9] [NP Not Present] [CORO 1]
ipmni10 [ipmem id 10] [NP Not Present] [CORO 1]
ipmni11 [ipmem id 11] [NP Not Present] [CORO 1]
ipmni12 [ipmem id 12] [NP Not Present] [CORO 2]
ipmni13 [ipmem id 13] [NP Not Present] [CORO 1]
ipmni14 [ipmem id 14] [NP Not Present] [CORO 2]
ipmni15 [ipmem id 15] [NP Not Present] [CORO 1]
ipmni16 [ipmem id 16] [NP Not Present] [CORO 2]
To run the following commands you need to specify an NI.
1:0 nidbg> ipmni_print_flags
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
flow error
- 0x1
flow commit
flow hardware
flow aged
flow flood
flow local
flow drop
- 0x2
- 0x4
- 0x8
- 0x10
- 0x20
- 0x40
forward last
forward hardware - 0x2
- 0x1
port last
- 0x1
menu switch
menu port
- 0x1
- 0x2
OmniSwitch Troubleshooting Guide September 2005
page 14-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
menu route
menu cmm
- 0x4
- 0x8
alarm
error
alert
config
table
egress
hardware
ingress igmp
message
ingress native
port updates
ingress tunnel
- 0x8
- 0x80
- 0x800
- 0x8000
- 0x80000
- 0x800000
- 0x8000000
- 0x80000000
- 0x4000
- 0x40000
- 0x400000
- 0x40000000
1:0 value = 0 = 0x0
1:0 nidbg> ipms_dbg|=0x40000; taskDelay 120; ipms_dbg = 0xfc
1:0 value = 262396 = 0x400fc
THU JUN 09 11:50:49 : IPMS (17) info message:
+++ IPMNI1 1/0
ipmni_mpm 285: 224.0.0.18 172.77.1.25 527 29
= test_free_buf_list + 0xb8
1:0
THU JUN 09 11:50:50 : IPMS (17) info message:
+++ IPMNI1 1/0
+++ IPMNI1 1/0
ipmni_mpm 285: 224.0.0.18 172.93.1.25 543 29
ipmni_mpm 285: 224.0.0.18 172.77.1.25 527 29
THU JUN 09 11:50:51 : IPMS (17) info message:
+++ IPMNI1 1/0
+++ IPMNI1 1/0
value = 0 = 0x0
1:0
ipmni_mpm 285: 224.0.0.18 172.93.1.25 543 29
ipmni_mpm 285: 224.0.0.18 172.77.1.25 527 29
ipms_dbg = 0x2d3bdc: value = 252 = 0xfc
1:0 nidbg> ipmni_print_state
1:0
mode
- (0xc3)
- (0xc3)
BU HW EN
BU
BU HW EN
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
configuration
capability
run
loop
init
ready
ok
recovery
- (0x40)
- y
- y
- y
- y
- y
- n
clock
id
flood
debug
- 246149
- 1
- 51
- 0xfc
priority
pay
length
max
- 0
- 10
- 100
- 380
entry
queue
watermark
pending
- 0
- 0
- 0
- 0
OmniSwitch Troubleshooting Guide September 2005
page 14-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
1:0
create
enqueue
global drop
flow drop
buffer
lock
queue
no frame
drops
lookup
fragment
frame
ip cksum
igmp cksum
grp
alloc
modify
free
- 0
- 0
- 0
- 3
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
- 0
send
recv
flow
duplicate
recovery
1:0 value = 0 = 0x0
OmniSwitch Troubleshooting Guide September 2005
page 14-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
OmniSwitch Troubleshooting Guide September 2005
page 14-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
OmniSwitch Troubleshooting Guide September 2005
page 14-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
OmniSwitch Troubleshooting Guide September 2005
page 14-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
OmniSwitch Troubleshooting Guide September 2005
page 14-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting IP Multicast Switching (IPMS)
Dshell Troubleshooting
OmniSwitch Troubleshooting Guide September 2005
page 14-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Troubleshooting DVMRP
Introduction
DVMRP is used to route Multicast packets through different IP Networks. This is a Dense Mode Multi-
cast Routing Protocol. Dense Mode refers to the network environment the protocol was designed to
service. Dense Mode protocols are designed for LAN environments where there are a lot of users and
bandwidth is plentiful. Sparse Mode Multicast Routing Protocols (Protocol Independent Multicast/Sparse-
Mode PIM/SM is an example) are designed for WAN environments where there are few users and a
limited amount of bandwidth.
Why have a Multicast Routing Protocol in your network? Multicast will not work in a routed environ-
ment. If a switch receives a multicast packet it will flood that packet out all ports in the VLAN, but it will
not forward out the router port. So, in order to have multicast packet across the network you will have to
bridge that packet across. This is not an ideal solution. A routed protocol like DVMRP will allow you to
keep your broadcasts domains intact and allow the multicast packets to go to the IP networks that need that
traffic.
DVMRP is a Flood/Prune protocol. What that means is when a switch has DVMRP enabled and receives a
multicast stream it floods that stream to all ports in that VLAN letting the DVMRP router know that the
multicast is available. Then the forwarding router listens for prune messages, indicating that certain
devices do not need that multicast. It can then stop sending to that port. If a prune message is not received,
the flooding will continue. If, after a prune, a multicast router receives an IGMP join for that multicast it
will send a Graft message. When a switch receives a Graft message for a multicast stream it does not know
about, it will forward that message to the other DVMRP switches connected to it. This process continues
until the graft reaches a switch with the multicast already being sent to clients.
DVMRP forwards multicast datagrams by computing the shortest (reverse) path tree from the source
(physical) network to all possible recipients of the multicast datagram.
A router is called a “parent” of the virtual network if that router is responsible for forwarding datagrams
onto that virtual network. The Virtual network can be considered a “child” virtual network of that router.
Using the child’s information the router can do Reverse path Broadcasting.
DVMRP Troubleshooting
Note that if a multicast stream is not working, it does not necessarily mean that IP multicast routing is at
fault. Verify that IP multicast switching is working properly.
DVMRP Global and Interface Commands
See the “DVMRP Commands” chapter in the OmniSwitch CLI Reference Guide for more information
about the following commands:
-> show ip dvmrp
DVMRP Admin Status
Flash Interval
Graft Timeout
= enabled,
= 5,
= 5,
Neighbor Interval
Neighbor Timeout
Prune Lifetime
Prune Timeout
= 10,
= 35,
= 7200,
= 3,
Report Interval
Route Holddown
= 60,
= 120,
page 15-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DVMRP
DVMRP Troubleshooting
Route Timeout
= 140,
= 6,
Number of Routes
Number of Reachable Routes = 6
-> show ip dvmrp interface
Address Vlan Tunnel Metric Admin-Status Oper-Status
-----------------+------+--------+--------+---------------+-------------
192.168.10.1
192.168.11.1
192.168.12.1
1
2
3
No
No
No
1
1
1
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
If an interface is not enabled then no multicast traffic will be routed to that VLAN the Interface represents.
What if everything is enabled in this switch correctly? It could be another switches problem or this switch
may be unable to process the messages correctly. Now see if you are seeing all the correct neighbors with
the following command.
-> show ip dvmrp neighbor
Neighbor Address Vlan
Uptime
Expires
GenID
Version State
----------------+------+-----------+-----------+-----------+---------+-------
192.168.12.3
192.168.11.2
3
2
00h:24m:19s 00h:00m:31s 1024473904 3.8
00h:23m:40s 00h:00m:35s 760301
active
3.255 active
If a neighbor is missing then it is likely that DVMRP does not recognize that device as a DVMRP neigh-
bor. Here is the way to see the multicast routing information.
-> show ip dvmrp route
Legends: Flags: L = Local, R = Remote, F = Flash, H = Holddown, I = Invalid
Address/Mask
Gateway
Metric
Age
Expires Flags
-------------------+------------------+------+-----------+---------+-----
192.168.10.0/24
192.168.11.0/24
192.168.12.0/24
192.168.13.0/24
192.168.14.0/24
192.168.15.0/24
-
-
-
1
1
1
2
2
2
00h:27m:13s
00h:27m:13s
00h:27m:13s
00h:25m:17s 02m:03s
00h:24m:49s 01m:45s
00h:24m:49s 01m:45s
-
-
-
L
L
L
R
R
R
192.168.11.2
192.168.12.3
192.168.12.3
The above commands are made easier if you have a detailed diagram. Using the diagram you can know
you Multicast VLANS and where they can be seen from any switch in the network. Local routes will not
be seen if the IP interface is not enabled in the switch or in DVMRP. If you see this, make sure the inter-
face is enabled with the following commands.
-> show ip dvmrp interface
Address
Vlan Tunnel Metric Admin-Status Oper-Status
-----------------+------+--------+--------+---------------+-------------
192.168.10.1
192.168.11.1
192.168.12.1
1
2
3
No
No
No
1
1
1
Disabled
Enabled
Enabled
Disabled
Enabled
Enabled
-> ip dvmrp interface 192.168.10.1
-> show ip dvmrp interface
Address
Vlan Tunnel Metric Admin-Status Oper-Status
-----------------+------+--------+--------+---------------+-------------
OmniSwitch Troubleshooting Guide September 2005
page 15-3
Download from Www.Somanuals.com. All Manuals Search And Download.
DVMRP Troubleshooting
Troubleshooting DVMRP
192.168.10.1
192.168.11.1
192.168.12.1
1
2
3
No
No
No
1
1
1
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Remote routes will be seen if they are learned from another switch. Again be sure that the interfaces are
enabled. If that is the case it possible that the other switch is not configured correctly.
If the above commands look good in your switch and in the other switches you can use the following
command to see if the switch has a next hop. If it does the problem may not be this switch. It may be the
next switch on the VLAN indicated here.
-> show ip dvmrp nexthop
Src Address/Mask
--------------------+-------+----------
192.168.10.25/24 branch
Vlan Hop Type
2
DVMRP Debug Commands
If you have looked at all the switches and you are sure you have configured correctly then it is time to use
the DVMRP Debug command.
-> show ip dvmrp debug
Debug Level
Error
Flash
Grafts
IGMP
Init
IPMRM
MIP
= 1,
= on,
= off,
= off,
= off,
= off,
= off,
= off,
= off
Misc
Nbr
= off,
= off,
= off,
= off,
= off,
= off,
Probes
Prunes
Routes
Time
TM
Notice that by default the Debug Level is 1 and the only Debug Type configured is error messages. These
can be changed with the following commands.
-> ip dvmrp debug-type ?
^
TM TIME ROUTES PRUNES PROBES NBR MISC MIP IPMRM INIT
IGMP GRAFTS FLASH ERROR ALL
(IP Routing & Multicast Command Set)
-> no ip dvmrp debug-type ?
^
TM TIME ROUTES PRUNES PROBES NBR MISC MIP IPMRM INIT
IGMP GRAFTS FLASH ERROR ALL
(IP Routing & Multicast Command Set)
-> ip dvmrp debug-level 95
-> ip dvmrp debug-level 1
The first command turns on a debug-type while the second turns off a debug type.
page 15-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DVMRP
DVMRP Troubleshooting
The third command turns on the debug level. The low is 0, which is no debugging at all, and the high is
110, which prints everything to the screen. There is so much going on in the switch and so much put to the
screen that an explanation of what level would bring what output. Instead we are recommending that a
setting of 95 is the most useful setting. If that setting does not yield the required information to derive the
problem the Customer Support will engage Engineering for more help.
Below is a recommended setting for use in conjunction with customer support. Keep in mind that more
testing may be needed, as this may not yield a reason for a failure. Follow the Customer Support Engi-
neers instructions. It is a good practice to disable DVMRP and then enable after the debug set-up is
accomplished. This is so you capture the entire communication between DVMRP routers.
-> show ip dvmrp debug
Debug Level
Error
Flash
Grafts
IGMP
Init
IPMRM
MIP
Misc
Nbr
Probes
Prunes
Routes
Time
= 1,
= on,
= off,
= on,
= on,
= on,
= on,
= off,
= off
= on,
= on
= on,
= on,
= off,
= off,
TM
-> ip dvmrp debug-level 95
-> ip dvmrp status enable
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
dvmrpSetGenId: Genid is 1025108923
dvmrpEnable: V1 Config=1 Oper=2
dvmrpProtoEnabledOnVlan: V1 mprotos=0x0
dvmrpSendIpmrmProto: V1 Configured
MIP and TM says we’re enabled.
dvmrpAddMembership: V1 do IP_ADD_MEMBERSHIP
dvmrpSendIpmrmProto: V1 Enabled
dvmrpAddIntf: look for 192.168.10.1-255.255.255.0
dvmrpAddIntf: found
dvmrpAddIntf: in holddown
dvmrpRibRemoveHoldDown: 192.168.10.0-255.255.255.0
dvmrpRibDelinkHoldDownQ: 192.168.10.0-255.255.255.0
V1 Remove-Discard-Source S,G 192.168.10.25,224.2.142.227
V1 Remove-Discard-Source S,G 192.168.10.25,224.2.178.69
dvmrpDeleteGListEntry: rt 192.168.10.0-255.255.255.0
dvmrpPurgeGroup:
dvmrpDelPrnSentForGrp:
dvmrpPurgeGroup:
dvmrpDelPrnSentForGrp:
dvmrpEnable: V2 Config=1 Oper=2
dvmrpProtoEnabledOnVlan: V2 mprotos=0x0
dvmrpSendIpmrmProto: V2 Configured
MIP and TM says we’re enabled.
dvmrpAddMembership: V2 do IP_ADD_MEMBERSHIP
dvmrpSendIpmrmProto: V2 Enabled
dvmrpAddIntf: look for 192.168.11.1-255.255.255.0
dvmrpAddIntf: found
dvmrpAddIntf: in holddown
OmniSwitch Troubleshooting Guide September 2005
page 15-5
Download from Www.Somanuals.com. All Manuals Search And Download.
DVMRP Troubleshooting
Troubleshooting DVMRP
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.11.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.12.0
tDvmrp-:
192.168.12.0
tDvmrp-:
tDvmrp-> -:
255.255.255.255
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
224.2.178.69
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.255
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
dvmrpRibRemoveHoldDown: 192.168.11.0-255.255.255.0
dvmrpRibDelinkHoldDownQ: 192.168.11.0-255.255.255.0
dvmrpInitChildAndSubs: All V1 nbrs dependent on us for rt
dvmrpDeleteGListEntry: rt 192.168.11.0-255.255.255.0
dvmrpEnable: V3 Config=1 Oper=2
dvmrpProtoEnabledOnVlan: V3 mprotos=0x0
dvmrpSendIpmrmProto: V3 Configured
MIP and TM says we’re enabled.
dvmrpAddMembership: V3 do IP_ADD_MEMBERSHIP
dvmrpSendIpmrmProto: V3 Enabled
dvmrpAddIntf: look for 192.168.12.1-255.255.255.0
dvmrpAddIntf: found
dvmrpAddIntf: in holddown
dvmrpRibRemoveHoldDown: 192.168.12.0-255.255.255.0
dvmrpRibDelinkHoldDownQ: 192.168.12.0-255.255.255.0
dvmrpInitChildAndSubs: All V1 nbrs dependent on us for rt
dvmrpInitChildAndSubs: All V2 nbrs dependent on us for rt
dvmrpDeleteGListEntry: rt 192.168.12.0-255.255.255.0
dvmrpRecvIpmrmSGInfo: V1 Lookup ipsa 192.168.10.25-
ipda 224.2.178.69, tsrc 0.0.0.0
Found route 192.168.10.0 to ipsa
Route looks good
Lookup S,G 192.168.10.25-255.255.255.255 224.2.178.69 on rib
dvmrpRecvIpmrmSGInfo: A new (S,G) entry
Insert S,G in rib’s list
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.178.69
#subords=0, pruncnt=0
Looking at V1...
V1 not sub/nbr
Looking at V2...
V2 not sub/nbr
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V2
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V3
# of IFs to fwd to: 0
No change in Forwarding vector list, return 0
Send NullRoute to IPMRM.
Null Route to IPMRM V1 192.168.10.25-255.255.255.255
dvmrpSendPrune:
Learned from local route, don’t send prune
dvmrpRecvIpmrmSGInfo: V1 Lookup ipsa 192.168.10.25-
ipda 224.2.142.227, tsrc 0.0.0.0
Found route 192.168.10.0 to ipsa
Route looks good
Lookup S,G 192.168.10.25-255.255.255.255 224.2.142.227 on rib
dvmrpRecvIpmrmSGInfo: A new (S,G) entry
Insert S,G in rib’s list
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.142.227
page 15-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DVMRP
DVMRP Troubleshooting
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
224.2.142.227
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.255
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
224.2.142.227
tDvmrp-:
255.255.255.255
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
224.2.178.69
tDvmrp-:
255.255.255.255
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
224.2.201.38
tDvmrp-:
tDvmrp-:
#subords=0, pruncnt=0
Looking at V1...
V1 not sub/nbr
Looking at V2...
V2 not sub/nbr
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V2
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V3
# of IFs to fwd to: 0
No change in Forwarding vector list, return 0
Send NullRoute to IPMRM.
Null Route to IPMRM V1 192.168.10.25-255.255.255.255
dvmrpSendPrune:
Learned from local route, don’t send prune
dvmrpRecvIpmrmSGInfo: V2 Lookup ipsa 192.168.13.25-
ipda 224.2.142.227, tsrc 0.0.0.0
Found route 192.168.13.0 to ipsa
Route looks good
Lookup S,G 192.168.13.25-255.255.255.255 224.2.142.227 on rib
dvmrpRecvIpmrmSGInfo: V2 S,G found 192.168.13.25 224.2.142.227
Prune state pending, send another Prune
dvmrpSendPrune:
Learned S,G from non-local route, upstrGw=192.168.11.2
dvmrpSendPrune: Unable to find nbr for Prune.
Null Route to IPMRM V2 192.168.13.25-255.255.255.255
dvmrpRecvIpmrmSGInfo: V2 Lookup ipsa 192.168.13.25-
ipda 224.2.178.69, tsrc 0.0.0.0
Found route 192.168.13.0 to ipsa
Route looks good
Lookup S,G 192.168.13.25-255.255.255.255 224.2.178.69 on rib
dvmrpRecvIpmrmSGInfo: V2 S,G found 192.168.13.25 224.2.178.69
Prune state pending, send another Prune
dvmrpSendPrune:
Learned S,G from non-local route, upstrGw=192.168.11.2
dvmrpSendPrune: Unable to find nbr for Prune.
Null Route to IPMRM V2 192.168.13.25-255.255.255.255
dvmrpRecvIpmrmSGInfo: V2 Lookup ipsa 192.168.13.25-
ipda 224.2.201.38, tsrc 0.0.0.0
Found route 192.168.13.0 to ipsa
Route looks good
Lookup S,G 192.168.13.25-255.255.255.255 224.2.201.38 on rib
dvmrpRecvIpmrmSGInfo: V2 S,G found 192.168.13.25 224.2.201.38
Prune state pending, send another Prune
dvmrpSendPrune:
Learned S,G from non-local route, upstrGw=192.168.11.2
dvmrpSendPrune: Unable to find nbr for Prune.
Null Route to IPMRM V2 192.168.13.25-255.255.255.255
IGMP packet from 192.168.10.1
IGMP packet from 192.168.10.1
OmniSwitch Troubleshooting Guide September 2005
page 15-7
Download from Www.Somanuals.com. All Manuals Search And Download.
DVMRP Troubleshooting
Troubleshooting DVMRP
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.10.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.11.0
tDvmrp-:
IGMP packet from 192.168.10.1
IGMP packet from 192.168.11.1
IGMP packet from 192.168.12.1
IGMP packet from 192.168.11.1
IGMP packet from 192.168.11.1
IGMP packet from 192.168.12.1
IGMP packet from 192.168.12.1
dvmrpRecvReport:
On V3 Unable to peer with nbr 192.168.12.3
dvmrpAddNeighbor: 192.168.12.3 new nbr
dvmrpAddAsSubordinate: No fwdr, add 192.168.12.3 as sub to rt
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.142.227
#subords=1, pruncnt=0
Looking at V1...
V1 not sub/nbr
Looking at V2...
V2 not sub/nbr
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V2
Looking at V3...
V3 is a sub/nbr, numFwdIfs=1
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.142.227
V1, GW 0.0.0.0, PruneSent 0
V3 (forward on)
Forward on 0 tunnels
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.178.69
#subords=1, pruncnt=0
Looking at V1...
V1 not sub/nbr
Looking at V2...
V2 not sub/nbr
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V2
Looking at V3...
V3 is a sub/nbr, numFwdIfs=1
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.178.69
V1, GW 0.0.0.0, PruneSent 0
V3 (forward on)
Forward on 0 tunnels
dvmrpAddAsSubordinate: No fwdr, add 192.168.12.3 as sub to rt
IGMP packet from 192.168.10.1
page 15-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DVMRP
DVMRP Troubleshooting
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
IGMP packet from 192.168.10.1
IGMP packet from 192.168.10.1
IGMP packet from 192.168.10.1
IGMP packet from 192.168.11.1
IGMP packet from 192.168.12.1
IGMP packet from 192.168.12.1
IGMP packet from 192.168.11.1
IGMP packet from 192.168.11.1
IGMP packet from 192.168.11.1
IGMP packet from 192.168.12.1
IGMP packet from 192.168.12.1
dvmrpRecvReport:
dvmrpUpdateRoute: V3 UPDATE route for 192.168.10.0-
orig metric 34 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=34, adj=34
dvmrpUpdatePoisoned:
Received on diff vlan
dvmrpUpdateRoute: V3 UPDATE route for 192.168.11.0-
orig metric 34 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=34, adj=34
dvmrpUpdatePoisoned:
Received on diff vlan
dvmrpUpdateRoute: V3 UPDATE route for 192.168.12.0-
orig metric 33 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Local, same vlan
dvmrpUpdateRoute: V3 UPDATE route for 192.168.13.0-
orig metric 35 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=35, adj=35
dvmrpUpdatePoisoned:
Received on diff vlan
dvmrpUpdateRoute: V3 UPDATE route for 192.168.14.0-
orig metric 1 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=1, adj=2
dvmrpUpdateReachable:
dvmrpRibRemoveHoldDown: 192.168.14.0-255.255.255.0
dvmrpRibDelinkHoldDownQ: 192.168.14.0-255.255.255.0
While holddown same nbr with same metric
dvmrpUpdateRoute: V3 UPDATE route for 192.168.15.0-
orig metric 1 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=1, adj=2
dvmrpUpdateReachable:
dvmrpRibRemoveHoldDown: 192.168.15.0-255.255.255.0
dvmrpRibDelinkHoldDownQ: 192.168.15.0-255.255.255.0
While holddown same nbr with same metric
dvmrpRecvPrune:
No netmask, so using 255.255.255.0
Pruning 192.168.10.0-255.255.255.0, 224.2.142.227
OmniSwitch Troubleshooting Guide September 2005
page 15-9
Download from Www.Somanuals.com. All Manuals Search And Download.
DVMRP Troubleshooting
Troubleshooting DVMRP
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.10.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
Found S,G matching source network 255.255.255.0
Creating a new prune state S,G 192.168.10.25 224.2.142.227
V3 time:218 Nbr:192.168.12.3
dvmrpPruneTimeEnQ:
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.142.227
#subords=1, pruncnt=1
Looking at V1...
Looking at V2...
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V2
Looking at V3...
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V3
# of IFs to fwd to: 0
Forwarding vector list changed, return 1
(dvmrpRecvPrune updates IPMRM)
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.142.227
V1, GW 0.0.0.0, PruneSent 0
Forward on 0 tunnels
dvmrpSendPrune:
Learned from local route, don’t send prune
dvmrpAddNeighbor: 192.168.11.2 new nbr
dvmrpAddAsSubordinate: No fwdr, add 192.168.11.2 as sub to rt
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.142.227
#subords=2, pruncnt=1
Looking at V1...
V1 not sub/nbr
Looking at V2...
V2 is a sub/nbr, numFwdIfs=1
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V2
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.142.227
V1, GW 0.0.0.0, PruneSent 0
V2 (forward on)
Forward on 0 tunnels
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.178.69
#subords=2, pruncnt=0
Looking at V1...
V1 not sub/nbr
Looking at V2...
V2 is a sub/nbr, numFwdIfs=1
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V2
Looking at V3...
page 15-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DVMRP
DVMRP Troubleshooting
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.12.0
tDvmrp-:
192.168.14.0
tDvmrp-:
192.168.15.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
V3 is a sub/nbr, numFwdIfs=2
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V3
# of IFs to fwd to: 2
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.178.69
V1, GW 0.0.0.0, PruneSent 0
V2 (forward on)
V3 (forward on)
Forward on 0 tunnels
dvmrpAddAsSubordinate: No fwdr, add 192.168.11.2 as sub to rt
dvmrpAddAsSubordinate: No fwdr, add 192.168.11.2 as sub to rt
dvmrpAddAsSubordinate: No fwdr, add 192.168.11.2 as sub to rt
IGMP packet from 192.168.12.3
dvmrpRecvPrune:
No netmask, so using 255.255.255.0
Pruning 192.168.10.0-255.255.255.0, 224.2.178.69
Found S,G matching source network 255.255.255.0
Creating a new prune state S,G 192.168.10.25 224.2.178.69
V3 time:255 Nbr:192.168.12.3
dvmrpPruneTimeEnQ:
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.178.69
#subords=2, pruncnt=1
Looking at V1...
V1 not sub/nbr
Looking at V2...
V2 is a sub/nbr, numFwdIfs=1
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V2
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
(dvmrpRecvPrune updates IPMRM)
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.178.69
V1, GW 0.0.0.0, PruneSent 0
V2 (forward on)
Forward on 0 tunnels
dvmrpRecvReport:
dvmrpUpdateRoute: V3 UPDATE route for 192.168.13.0-
orig metric 32 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=32, adj=32
IGMP packet from 192.168.12.3
dvmrpRecvReport:
dvmrpUpdateRoute: V2 UPDATE route for 192.168.10.0-
orig metric 32 frm 192.168.11.2
dvmrpUpdatePresentRoute:
OmniSwitch Troubleshooting Guide September 2005
page 15-11
Download from Www.Somanuals.com. All Manuals Search And Download.
DVMRP Troubleshooting
Troubleshooting DVMRP
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
Metric orig=32, adj=32
dvmrpUpdateUnreachable:
Nbr[192.168.11.2] no longer a subordinate for rt 192.168.10.0
dvmrpUpdateUnreachable Nbr[192.168.11.2] no longer a subordi-
nate for rt 192.168.10.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.142.227
#subords=1, pruncnt=1
Looking at V1...
Looking at V2...
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V2
Looking at V3...
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V3
# of IFs to fwd to: 0
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.142.227
V1, GW 0.0.0.0, PruneSent 0
Forward on 0 tunnels
dvmrpSendPrune:
Learned from local route, don’t send prune
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.178.69
#subords=1, pruncnt=1
Looking at V1...
Looking at V2...
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V2
Looking at V3...
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V3
# of IFs to fwd to: 0
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.178.69
V1, GW 0.0.0.0, PruneSent 0
Forward on 0 tunnels
dvmrpSendPrune:
Learned from local route, don’t send prune
dvmrpUpdateRoute: V2 UPDATE route for 192.168.11.0-
orig metric 1 frm 192.168.11.2
dvmrpUpdatePresentRoute:
Local, same vlan
dvmrpUpdateRoute: V2 UPDATE route for 192.168.12.0-
orig metric 32 frm 192.168.11.2
dvmrpUpdatePresentRoute:
Metric orig=32, adj=32
dvmrpUpdateUnreachable:
Nbr[192.168.11.2] no longer a subordinate for rt 192.168.12.0
dvmrpUpdateUnreachable Nbr[192.168.11.2] no longer a subordi-
nate for rt 192.168.12.0
page 15-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DVMRP
DVMRP Troubleshooting
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.11.2
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
dvmrpUpdateRoute: V2 UPDATE route for 192.168.13.0-
orig metric 1 frm 192.168.11.2
dvmrpUpdatePresentRoute:
Metric orig=1, adj=2
dvmrpUpdateReachable:
dvmrpRibRemoveHoldDown: 192.168.13.0-255.255.255.0
dvmrpRibDelinkHoldDownQ: 192.168.13.0-255.255.255.0
V2 Remove-Discard-Source S,G 192.168.13.25,224.0.1.24
V2 Remove-Discard-Source S,G 192.168.13.25,224.2.142.227
V2 Remove-Discard-Source S,G 192.168.13.25,224.2.178.69
V2 Remove-Discard-Source S,G 192.168.13.25,224.2.201.38
While holddown same nbr with same metric
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.13.0 - grp 224.0.1.24
#subords=0, pruncnt=0
Looking at V1...
V1 not sub/nbr
V1 not rib->upstrVl=2, may need forwarding
Group 224.0.1.24 not learned on V1
Looking at V2...
V2 not sub/nbr
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=2, may need forwarding
Group 224.0.1.24 not learned on V3
# of IFs to fwd to: 0
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.13.25-255.255.255.255 224.0.1.24
V2, GW 192.168.11.2, PruneSent 0
Forward on 0 tunnels
dvmrpSendPrune:
Learned S,G from non-local route, upstrGw=192.168.11.2
dvmrpSetMinPruneTime:
Set prSent timer 7200
Prune S,G 192.168.13.25 224.0.1.24 time 7200 V2 Nbr
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.13.0 - grp 224.2.142.227
#subords=0, pruncnt=0
Looking at V1...
V1 not sub/nbr
V1 not rib->upstrVl=2, may need forwarding
Group 224.2.142.227 not learned on V1
Looking at V2...
V2 not sub/nbr
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=2, may need forwarding
Group 224.2.142.227 not learned on V3
# of IFs to fwd to: 0
No change in Forwarding vector list, return 0
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.13.0 - grp 224.2.178.69
OmniSwitch Troubleshooting Guide September 2005
page 15-13
Download from Www.Somanuals.com. All Manuals Search And Download.
DVMRP Troubleshooting
Troubleshooting DVMRP
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
#subords=0, pruncnt=0
Looking at V1...
V1 not sub/nbr
V1 not rib->upstrVl=2, may need forwarding
Group 224.2.178.69 not learned on V1
Looking at V2...
V2 not sub/nbr
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=2, may need forwarding
Group 224.2.178.69 not learned on V3
# of IFs to fwd to: 0
No change in Forwarding vector list, return 0
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.13.0 - grp 224.2.201.38
#subords=0, pruncnt=0
Looking at V1...
V1 not sub/nbr
V1 not rib->upstrVl=2, may need forwarding
Group 224.2.201.38 not learned on V1
Looking at V2...
V2 not sub/nbr
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=2, may need forwarding
Group 224.2.201.38 not learned on V3
# of IFs to fwd to: 0
No change in Forwarding vector list, return 0
dvmrpUpdateRoute: V2 UPDATE route for 192.168.14.0-
orig metric 32 frm 192.168.11.2
dvmrpUpdatePresentRoute:
Metric orig=32, adj=32
dvmrpUpdateUnreachable:
Nbr[192.168.11.2] no longer a subordinate for rt 192.168.14.0
dvmrpUpdateUnreachable Nbr[192.168.11.2] no longer a subordi-
nate for rt 192.168.14.0
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
dvmrpUpdateRoute: V2 UPDATE route for 192.168.15.0-
orig metric 32 frm 192.168.11.2
dvmrpUpdatePresentRoute:
Metric orig=32, adj=32
dvmrpUpdateUnreachable:
Nbr[192.168.11.2] no longer a subordinate for rt 192.168.15.0
dvmrpUpdateUnreachable Nbr[192.168.11.2] no longer a subordi-
nate for rt 192.168.15.0
tDvmrp-:
dvmrpNegCacheTout: (S,G) timeout 192.168.13.25-255.255.255.0
224.0.1.24
tDvmrp-:
dvmrpRecvReport:
tDvmrp-:
dvmrpUpdateRoute: V3 UPDATE route for 192.168.13.0-
255.255.255.0
tDvmrp-:
tDvmrp-:
orig metric 35 frm 192.168.12.3
dvmrpUpdatePresentRoute:
tDvmrp-:
Metric orig=35, adj=35
tDvmrp-:
dvmrpUpdatePoisoned:
tDvmrp-:
Received on diff vlan
tDvmrp-:
Nbr 192.168.12.3 indicating dependency for [192.168.13.0-
255.255.255.0]
page 15-14
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DVMRP
DVMRP Troubleshooting
tDvmrp-:
192.168.13.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.11.2
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.11.2
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
dvmrpUpdatePoisoned: nbr 192.168.12.3 is dependent on us for rt
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.13.0 - grp 224.0.1.24
#subords=1, pruncnt=0
Looking at V1...
V1 not sub/nbr
V1 not rib->upstrVl=2, may need forwarding
Group 224.0.1.24 not learned on V1
Looking at V2...
V2 not sub/nbr
Looking at V3...
V3 is a sub/nbr, numFwdIfs=1
V3 not rib->upstrVl=2, may need forwarding
Group 224.0.1.24 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.13.25-255.255.255.255 224.0.1.24
V2, GW 192.168.11.2, PruneSent 1
V3 (forward on)
Forward on 0 tunnels
dvmrpSendGraft: cancel prSent timer
dvmrpSendGraftPkt: V2 S,G 192.168.13.25 224.0.1.24 Nbr
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.13.0 - grp 224.2.142.227
#subords=1, pruncnt=0
Looking at V1...
V1 not sub/nbr
V1 not rib->upstrVl=2, may need forwarding
Group 224.2.142.227 not learned on V1
Looking at V2...
V2 not sub/nbr
Looking at V3...
V3 is a sub/nbr, numFwdIfs=1
V3 not rib->upstrVl=2, may need forwarding
Group 224.2.142.227 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.13.25-255.255.255.255 224.2.142.227
V2, GW 192.168.11.2, PruneSent 1
V3 (forward on)
Forward on 0 tunnels
dvmrpSendGraft: cancel prSent timer
dvmrpSendGraftPkt: V2 S,G 192.168.13.25 224.2.142.227 Nbr
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.13.0 - grp 224.2.178.69
#subords=1, pruncnt=0
Looking at V1...
V1 not sub/nbr
V1 not rib->upstrVl=2, may need forwarding
OmniSwitch Troubleshooting Guide September 2005
page 15-15
Download from Www.Somanuals.com. All Manuals Search And Download.
DVMRP Troubleshooting
Troubleshooting DVMRP
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.11.2
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
192.168.11.2
tDvmrp-:
192.168.11.2
tDvmrp-:
224.0.1.24
tDvmrp-:
192.168.11.2
tDvmrp-:
224.2.142.227
tDvmrp-:
192.168.11.2
tDvmrp-:
224.2.178.69
tDvmrp-:
192.168.11.2
tDvmrp-:
224.2.201.38
Group 224.2.178.69 not learned on V1
Looking at V2...
V2 not sub/nbr
Looking at V3...
V3 is a sub/nbr, numFwdIfs=1
V3 not rib->upstrVl=2, may need forwarding
Group 224.2.178.69 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.13.25-255.255.255.255 224.2.178.69
V2, GW 192.168.11.2, PruneSent 1
V3 (forward on)
Forward on 0 tunnels
dvmrpSendGraft: cancel prSent timer
dvmrpSendGraftPkt: V2 S,G 192.168.13.25 224.2.178.69 Nbr
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.13.0 - grp 224.2.201.38
#subords=1, pruncnt=0
Looking at V1...
V1 not sub/nbr
V1 not rib->upstrVl=2, may need forwarding
Group 224.2.201.38 not learned on V1
Looking at V2...
V2 not sub/nbr
Looking at V3...
V3 is a sub/nbr, numFwdIfs=1
V3 not rib->upstrVl=2, may need forwarding
Group 224.2.201.38 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.13.25-255.255.255.255 224.2.201.38
V2, GW 192.168.11.2, PruneSent 1
V3 (forward on)
Forward on 0 tunnels
dvmrpSendGraft: cancel prSent timer
dvmrpSendGraftPkt: V2 S,G 192.168.13.25 224.2.201.38 Nbr
dvmrpRecvGraftAck: V2 S,G 192.168.13.25 224.0.1.24 Nbr
dvmrpDelGacksForGroup: Delete Gack for S,G 192.168.13.0
dvmrpRecvGraftAck: V2 S,G 192.168.13.25 224.2.142.227 Nbr
dvmrpDelGacksForGroup: Delete Gack for S,G 192.168.13.0
dvmrpRecvGraftAck: V2 S,G 192.168.13.25 224.2.178.69 Nbr
dvmrpDelGacksForGroup: Delete Gack for S,G 192.168.13.0
dvmrpRecvGraftAck: V2 S,G 192.168.13.25 224.2.201.38 Nbr
dvmrpDelGacksForGroup: Delete Gack for S,G 192.168.13.0
page 15-16
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DVMRP
DVMRP Troubleshooting
-> tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrps-:
tDvmrp-:
tDvmrp-:
tDvmrph-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvrp - :
dvmrpRecvIpmrmDelEntry: V2 S,G 192.168.13.25-255.255.255.255
224.2.142.227
Found route 192.168.13.0 to ipsa
S,G entry found for deletion
dvmrpPurgeGroup:
dvmrpDelPrnSentForGrp:
dvmrpRecvIpmrmDelEntry: V2 S,G 192.168.13.25-255.255.255.255
224.2.201.38
Found route 192.168.13.0 to ipsa
S,G entry found for deletion
dvmrpPurgeGroup:
dvmrpDelPrnSentForGrp:
dvmrpRecvIpmrmDelEntry: V2 S,G 192.168.13.25-255.255.255.255
224.2.178.69
Found route 192.168.13.0 to ipsa
S,G entry found for deletion
dvmrpPurgeGroup:
dvmrpDelPrnSentForGrp:
dvmrpRecvReport:
dvmrpUpdateRoute: V3 UPDATE route for 192.168.10.0-
orig metric 34 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=34, adj=34
dvmrpUpdatePoisoned:
Received on diff vlan
dvmrpUpdateRoute: V3 UPDATE route for 192.168.11.0-
orig metric 34 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=34, adj=34
dvmrpUpdatePoisoned:
Received on diff vlan
dvmrpUpdateRoute: V3 UPDATE route for 192.168.12.0-
orig metric 33 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Local, same vlan
dvmrpUpdateRoute: V3 UPDATE route for 192.168.13.0-
orig metric 35 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=35, adj=35
dvmrpUpdatePoisoned:
Received on diff vlan
dvmrpUpdateRoute: V3 UPDATE route for 192.168.14.0-
orig metric 1 frm 192.168.12.3
dvmrpUpdatePresentRoute:
Metric orig=1, adj=2
dvmrpUpdateReachable:
dvmrpRibResetAgeoutTimer:
dvmrpUpdateRoute: V3 UPDATE route for 192.168.15.0-
orig metric 1 frm 192.168.12.3
dvmrpUpdatPresentRoute:
OmniSwitch Troubleshooting Guide September 2005
page 15-17
Download from Www.Somanuals.com. All Manuals Search And Download.
DVMRP Troubleshooting
Troubleshooting DVMRP
tDvm-> rpshow -:
tDvmrp-:
tDvmrp-:
Metric orig=1, adj=2
dvmrpUpdateReachable:
dvmrpRibResetAgeoutTimer:
-> show ip dvmrp route
tDvmrp-:
tDvmrp-:
255.255.255.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
255.255.255.0]
tDvmrp-:
192.168.10.0
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
tDvmrp-:
dvmrpRecvReport:
dvmrpUpdateRoute: V2 UPDATE route for 192.168.10.0-
orig metric 34 frm 192.168.11.2
dvmrpUpdatePresentRoute:
Metric orig=34, adj=34
dvmrpUpdatePoisoned:
Received on diff vlan
Nbr 192.168.11.2 indicating dependency for [192.168.10.0-
dvmrpUpdatePoisoned: nbr 192.168.11.2 is dependent on us for rt
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.142.227
#subords=2, pruncnt=1
Looking at V1...
V1 not sub/nbr
Looking at V2...
V2 is a sub/nbr, numFwdIfs=1
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V2
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.142.227 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.142.227
V1, GW 0.0.0.0, PruneSent 0
V2 (forward on)
Forward on 0 tunnels
dvmrpComputeForwardingVectorForRoute: call it...
dvmrpComputeForwardingVector:
For rt 192.168.10.0 - grp 224.2.178.69
#subords=2, pruncnt=1
Looking at V1...
V1 not sub/nbr
Looking at V2...
V2 is a sub/nbr, numFwdIfs=1
V2 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V2
Looking at V3...
V3 not sub/nbr
V3 not rib->upstrVl=1, may need forwarding
Group 224.2.178.69 not learned on V3
# of IFs to fwd to: 1
Forwarding vector list changed, return 1
dvmrpComputeForwardingVectorForRoute: Update IPMRM
dvmrpSendIpmrmRoute: Update/add to IPMRM S,G
192.168.10.25-255.255.255.255 224.2.178.69
page 15-18
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting DVMRP
DVMRP Troubleshooting
tDvmrp-:
tDvmrp-:
tDvmrp-:
V1, GW 0.0.0.0, PruneSent 0
V2 (forward on)
Forward on 0 tunnels
tDvmrp-:
dvmrpUpdateRoute: V2 UPDATE route for 192.168.11.0-
255.255.255.0
tDvmrp-:
tDvmrp-:
orig metric 1 frm 192.168.11.2
dvmrpUpdatePresentRoute:
tDvmrp-:
Local, same vlan
tDvmrp-:
dvmrpUpdateRoute: V2 UPDATE route for 192.168.12.0-
255.255.255.0
tDvmrp-:
tDvmrp-:
orig metric 34 frm 192.168.11.2
dvmrpUpdatePresentRoute:
tDvmrp-:
Metric orig=34, adj=34
tDvmrp-:
dvmrpUpdatePoisoned:
tDvmrp-:
Received on diff vlan
tDvmrp-:
Nbr 192.168.11.2 indicating dependency for [192.168.12.0-
255.255.255.0]
tDvmrp-:
192.168.12.0
tDvmrp-:
dvmrpUpdatePoisoned: nbr 192.168.11.2 is dependent on us for rt
dvmrpUpdateRoute: V2 UPDATE route for 192.168.13.0-
255.255.255.0
tDvmrp-:
tDvmrp-:
orig metric 1 frm 192.168.11.2
dvmrpUpdatePresentRoute:
tDvmrp-:
Metric orig=1, adj=2
tDvmrp-:
dvmrpUpdate Reachable:
tDvmrp-:
dvmrpRibResetAgeoutTimer:
tDvmrp-:
dvmrpUpdateRoute: V2 UPDATE route for 192.168.14.0-
255.255.255.0
tDvmrp-:
tDvmrp-:
orig metric 35 frm 192.168.11.2
dvmrpUpdatePresentRoute:
tDvmrp-:
Metric orig=35, adj=35
tDvmrp-:
dvmrpUpdatePoisoned:
tDvmrp-:
Received on diff vlan
tDvmrp-:
Nbr 192.168.11.2 indicating dependency for [192.168.14.0-
255.255.255.0]
tDvmrp-:
192.168.14.0
tDvmrp-:
dvmrpUpdatePoisoned: nbr 192.168.11.2 is dependent on us for rt
dvmrpUpdateRoute: V2 UPDATE route for 192.168.15.0-
255.255.255.0
tDvmrp-:
tDvmrp-:
orig metric 35 frm 192.168.11.2
dvmrpUpdatePresentRoute:
tDvmrp-:
Metric orig=35, adj=35
tDvmrp-:
dvmrpUpdatePoisoned:
tDvmrp-:
Received on diff vlan
tDvmrp-:
Nbr 192.168.11.2 indicating dependency for [192.168.15.0-
255.255.255.0]
tDvmrp-:
dvmrpUpdatePoisoned: nbr 192.168.11.2 is dependent on us for rt
192.168.15.0
-> ip dvmrp debug-level 0
-> debug ip dvmrp route vlan 515
Address|
172.66.0.0|
Mask|Met|
255.255.0.0| 2| 107| 515|
Exp|Vlan|
Gateway|Flags
172.65.1.23| R
1.
Total # Routes learned on Vlan [515] --------------: 1
-> debug ip dvmrp nbr
Vlan| Intf Address|
Mask|Metric| # Nbrs
OmniSwitch Troubleshooting Guide September 2005
page 15-19
Download from Www.Somanuals.com. All Manuals Search And Download.
DVMRP Troubleshooting
Troubleshooting DVMRP
100| 172.100.1.25| 255.255.255.0|
515| 172.65.1.25| 255.255.0.0|
1|
1|
0|
1|
-> debug ip dvmrp group
Vlan | Group | G Mode |
Src | S Mode
-> debug ip dvmrp prune
************Prune Table******************
| Actn|
total=0
Source |
Group|
Neighbor| Time|Vlan| Exp
7800-1 -> debug ip dvmrp graft
***********Graft Status******************
Source | Group| Neighbor|Vlan| Ack|Time
|
-> debug ip dvmrp timer
CALLOUT QUEUE:
[PRB3] id=365 time=1
[PRB4] id=366 time=2
[PRB5] id=367 time=2
[PRB1] id=368 time=2
[PRB2] id=370 time=2
[RRT V515] id=348 time=16
[NBT V515] id=369 time=8
-> debug ip dvmrp rib ageq
No.
1
Addr/Mask
172.66.0.0/16
UpVl
515
UpGw
Age
Exp
Kids Subs
172.65.1.23 00h:04m:35s 01m:44s
1
0
-> debug ip dvmrp rib holdq
No.
Addr/Mask
UpVl
UpGw
Age
Exp
Kids Subs
->
page 15-20
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
16 Troubleshooting PIM-SM
In order to troubleshoot issues related to Protocol Independent Multicast-Sparse Mode (PIM-SM), a basic
understanding of the protocol—as well as IP multicast technology—are required. Basic PIM-SM concepts
are explained below; for detailed protocol specifications please refer to RFC 2362 (PIM-SM) as well as
the OmniSwitch 7700/7800/8800 Advanced Routing Configuration Guide, which contains a protocol over-
view and PIM-SM configuration information.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 16-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Troubleshooting PIM-SM
Introduction
Traditional multicast routing protocols like DVMRP, MOSPF or PIM-DM were implemented to provide
multicast routing in campus network. These traditional dense mode multicast protocol were intended for
use within regions where a group is widely represented or bandwidth is not an issue. However when group
members and senders to these groups are sparsely distributed across a wide area, traditional multicast rout-
ing protocol schemes do not provide an efficient way to establish distribution trees. For instance member-
ship reports or data packets are being eventually forwarded over many links where no receivers or senders
are located.
PIM-SM architecture provides a way for efficiently routing to multicast groups that may span wide area
Internets. PIM-SM, including those with WAN links, scales well to a network of any size. The explicit join
mechanism will prevent unwanted traffic from flooding the WAN links. Data multicast traffic will be
forwarded only to networks segment that have active receivers which have specifically requested the data.
PIM-SM uses a shared tree to distribute the information about active sources. Depending on the configura-
tion options the traffic can remain on the shared tree or switch over to an optimized source distribution tree
called Shortest Path Tree, SPT. The traffic starts to flow down the shared tree and then routers along the
path determine if there is a better path to the source. If a better, more direct path exists the designated
router (router closest to the receiver) will send a “join” message towards the source and then re-route the
traffic along this path.
PIM-SM uses the concept of Rendezvous Point (RP). Sources register with the RP and then data is
forwarded down the shared tree to the receivers. If the shared tree is not an optimal path between the
source and the receiver the routers will dynamically create a source tree and stop traffic from flowing
down the shared tree.
Definition of Terms
Bootstrap Router (BSR). A BSR is dynamically elected between the C-BSR (candidates BSR) within a
PIM-SM domain. Bootstrap messages are sent to discover all C-BSR and associated CBSR priority. The
BSR is the router with the highest CBSR priority. It is responsible for sending bootstrap messages, which
contains RP-Set.
Designated Router (DR). The DR is the highest IP addressed PIM-SM router on a LAN segment. It is
responsible for sending corresponding Join/Prune messages to the RP on behalf of directly connected
receivers and sources.
Rendezvous Point (RP). Each multicast group has a shared-tree via which receivers receives data from
sources. The RP is the root of this per-group shared tree, called RP tree. C-RPs (Candidates RP) are PIM-
SM routers configured to eventually become RP for some or all multicast groups address. Priority can also
be configured for a C-RP and will be used on DR when membership to a multicast group is required.
RP-Set. List of reachable C-RP sent in bootstrap messages distributed by the BSR to all PIM-SM router in
the domain. The BSR compiles the list based on C-RP advertisement. C-RPs periodically unicast C-RP-
Advertisements to the BSR for that domain The RP-Set details each C-RP with their group multicast
address availability. DRs store these bootstrap messages and use it when membership to a specific multi-
cast group is required.
RP Tree (Shared Tree). The set of paths connecting all receivers of a group to the RP.
Shortest Path Tree (SPT). The SPT is the multicast distribution tree that connects, using the shortest
path, receivers of a specific group to the source. The SPT computation is based on unicast routing but is
not depending on any particular unicast routing protocol.
page 16-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
Protocol Overview
Protocol Overview
DR Election
Hello messages are sent periodically between PIM neighbors. This informs routers which interface has
PIM neighbors. Hello messages are multicast packets using address 224.0.0.13, which corresponds to
ALL-PIM-ROUTERS group.
When a router receives a Hello message, it stores the IP address for that neighbor and determines the
Designated Router (DR) for that specific interface. The highest IP address system is elected DR. DR infor-
mation is refreshed on each Hello messages received. Holdtime parameter is the amount of time a receiver
must keep the neighbor reachable, in seconds.
192.168.11.3/24
Hello pkt
192.168.11.4/24
Hello pkt
192.168.11/24
segment
Ethernet
192.168.11.1/24
Hello pkt
Hello pkt
192.168.11.2/24
Simplified Hello Message Format
IP: ----- IP Header -----
IP: Protocol
= 103 (PIM)
= [192.168.11.1]
IP: Source address
IP: Destination address = [224.0.0.13]
OmniSwitch Troubleshooting Guide September 2005
page 16-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Protocol Overview
Troubleshooting PIM-SM
PIM: ----- PIM Header -----
PIM:
PIM: Version
= 2
PIM: Message Type = 0 (Hello)
PIM: Reserved
PIM: Checksum
PIM: Option Type
= 0
= 4017 (correct)
= 1 (PIM-SM)
PIM: Option Length = 2
PIM: Option Value = 0x0069 (Hold time in seconds)
Debugging Hello Messages
To debug DR election and view Hello messages sent and received on PIM router interface, use the follow-
ing commands:
-> ip pimsm debug-type hello
-> ip pimsm debug-level 100
Debug output:
tPimsm-:
tPimsm-:
tPimsm-:
Sending hello on 2 with IP 192.168.12.1
Sending hello on 100 with IP 10.1.1.1
Sending hello on 1 with IP 192.168.11.1
Sending hello on 2 is a Hello message sent on VLAN 2, and the interface with IP 192.168.12.1 is the
router interface sending the Hello message
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
Received hello from 192.168.11.2 on 1, len=22
Recvd. hello from 192.168.11.2 on vlan 1 Holdtime 105
Recvd. hello from 192.168.11.2 on vlan 1 Priority 1
Recvd. hello from 192.168.11.2 on vlan 1 Genid 56455
Received hello from 192.168.11.2 is the sender of the Hello message on 1. len=22 is respectively the
VLAN on which the packet is received, and the packet length Holdtime 105 is the holdtime in seconds.
Priority 1 all PIM-SM routers have the same value and are not configurable.
Genid 56455.
page 16-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
Protocol Overview
Related CLI Command
To view if a PIM router interface is the DR for the LAN segment, enter the following command:
-> show ip pimsm neighbor
Neighbor Address Vlan
Uptime
Expires
Mode
-----------------+--------+-----------+-----------+---------
192.168.11.2
192.168.12.2
2
2
17h:49m:48s 00h:01m:28s Sparse (DR)
17h:19m:34s 00h:01m:15s Sparse (DR)
If (DR) is not present it means the interface has not DR role on the segment.
OmniSwitch Troubleshooting Guide September 2005
page 16-5
Download from Www.Somanuals.com. All Manuals Search And Download.
BSR Election
Troubleshooting PIM-SM
BSR Election
Candidates-BSR sends Bootstrap messages within its PIM-SM domain. Bootstrap messages are multicast
to the ALL-PIM-ROUTERS group. Bootstrap message parameters C-BSR ID, which are equal to the BSR
IP address, and the C-BSR priority, are used for the BSR election. The BSR will be the router with the
highest priority; in case the routers have the same priority, the highest IP address will become the BSR.
After BSR has been elected, intermediate routers forward Bootstrap messages originated at the BSR.
192.168.11.2
bootstrap message
source ip 192.168.9.2
BSR ID 192.168.11.1
BSR priority 0
bootstrap message
BSR ID 192.168.11.1
BSR priority 0
3Com
3Com
3Com
bootstrap message
BSR ID 192.168.11.2
BSR priority 0
192.168.9.2
192.168.9.4
bootstrap message
source ip 192.168.10.2
BSR ID 192.168.11.1
BSR priority 0
192.168.10.2
3Com
192.168.10.3
page 16-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
BSR Election
Simplified Packet Format
IP: ----- IP Header -----
IP: Protocol
= 103 (PIM)
= [192.168.11.2]
IP: Source address
IP: Destination address = [224.0.0.13]
PIM: ----- PIM Header -----
PIM:
PIM: Version
= 2
PIM: Message Type = 4(Bootstrap)
PIM: Reserved
= 0
PIM: Checksum
= 71af (correct)
= 0
PIM: Fragment tag
PIM: Hash mask length
PIM: BSR-priority
= 30
= 0
Debugging BSR/Bootstrap
Commands to debug received and forwarded bootstrap, the command will return information on BSR
election as well as Bootstrap messages in general.
-> ip pimsm debug-type bootstrap
-> ip pimsm debug-level 100
Debug output on 192.168.11.2:
tPimsm-:
pimsmBSRStateTransition - Entering with Event TMR State : CAND
OperStatus DOWN
tPimsm-:
Originate msg.State change to ELCTD
Transitioning from status down to up in order to participate to BSR election.
tPimsm-: BSR Available : 192.168.11.2
C-BSR is the address that will be used in the generated Bootstrap messages.
tPimsm-:
pimsmBSRStateTransition - Leaving with Event TMR State : ELCTD
Status UP
OmniSwitch Troubleshooting Guide September 2005
page 16-7
Download from Www.Somanuals.com. All Manuals Search And Download.
BSR Election
Troubleshooting PIM-SM
The router selects itself as initial BSR.
tPimsm-:
Received bootstrap message from 192.168.11.1, bsr
addr:192.168.11.1 on vlan 1
tPimsm-:
Ignoring less preferred bsr 192.168.11.1, Pri 0. Bsr
192.168.11.2, Pri 0
Bootstrap message received and action taken, notice BSR ID and BSR priority.
tPimsm-:
Received bootstrap message from 192.168.11.1, bsr
addr:192.168.11.1 on vlan 1
tPimsm-:
Ignoring less preferred bsr 192.168.11.1, Pri 0. Bsr
192.168.11.2, Pri 0
tPimsm-:
tPimsm-:
Sent BS on vlan 1 ipda = 224.0.0.13
Sent BS on vlan 1 ipda = 224.0.0.13
Bootstrap messages sent with IP destination and VLAN information.
Debug output on 192.168.11.1:
tPimsm-:
pimsmBSRStateTransition - Entering with Event TMR State : CAND
OperStatus DOWN
tPimsm-:
tPimsm-:
Originate msg.State change to ELCTD
BSR Available : 192.168.11.1
tPimsm-:
pimsmBSRStateTransition - Leaving with Event TMR State : ELCTD
Status UP
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
Sent BS on vlan 1 ipda = 224.0.0.13
Sent BS on vlan 2 ipda = 224.0.0.13
Sent BS on vlan 1 ipda = 224.0.0.13
Sent BS on vlan 2 ipda = 224.0.0.13
Received bootstrap message from 192.168.11.2, bsr
addr:192.168.11.2 on vlan 1
tPimsm-:
pimsmBSRStateTransition - Entering with Event CHNG State :
ELCTD OperStatus UP
Received bootstrap triggered BSR change.
tPimsm-:
BSR Available : 192.168.11.2
Election of a New BSR
tPimsm-:
pimsmBSRStateTransition - Leaving with Event CHNG State : CAND
Status UP
........
Forwarding BSR on VLAN 2
Bootstrap message forwarded on the corresponding VLAN.
page 16-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
BSR Election
Related CLI Command
To view which routers are assuming the role of the BSR, expiry time, C-BSR address, and C-BSR prior-
ity, type:
-> show ip pimsm
Status
= enabled,
= 192.168.13.1,
= 00h:02m:01s,
= 0.0.0.0,
= 30,
BSR Address
BSR Expiry Time
CBSR Address
CBSR Mask Length
CBSR Priority
.......
= 0,
IF you don’t want a PIM router to assume BSR role, enter the following syntax:
-> no ip pimsm cbsr-address
This command will result in a C-BSR address of 0.0.0.0
OmniSwitch Troubleshooting Guide September 2005
page 16-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C-RP Advertisements
Troubleshooting PIM-SM
C-RP Advertisements
Candidate-RPs advertisements are periodically unicast from the C-RP to the BSR. These advertisements
contain group multicast address the router can be responsible for and the priority for the corresponding
group address. C-RP could be configured to participate as RP for specific multicast groups or for all multi-
cast groups. Highest priority will be 0. Other parameters present in the packet are:
• Holdtime timer, which is the amount of time the advertisement, is valid.
• The prefix count, which tells the number of group addresses contained in the advertisement.
• The unicast RP address which is the interface to advertise as RP.
• The mask length.
BSR
192.168.11.1
192.168.11.2
3Com
3Com
3Com
192.168.9.2
192.168.9.4
192.168.10.2
3Com
C-RP-Adv
RP address 192.168.10.3
Mluticast Group 225.1.1.1
192.168.10.3
Simplified RP-Advertisement Packet Format
IP: ----- IP Header -----
IP: Protocol
= 103 (PIM)
IP: Header checksum = DF9E (correct)
IP: Source address = [192.168.10.3]
IP: Destination address = [192.168.11.1]
IP: No options
IP:
page 16-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
C-RP Advertisements
PIM: ----- PIM Header -----
PIM: Version
= 2
PIM: Message Type = 8(Candidate-RP-Advertisement)
PIM: Reserved
PIM: Checksum
PIM: Prefix count
PIM: Priority
= 0
= 269d (correct)
= 1
= 0
= 150 (in seconds)
PIM: Holdtime
PIM: *** Encoded-Unicast-RP-Address ***
PIM: Address family = 1 (IP (IP version 4))
PIM: Encoding type = 0
PIM: Unicast address = [192.168.11.1]
PIM:
PIM: *** Encoded Group Address-1 ***
PIM: Address family
PIM: Encoding type
PIM: Reserved
= 1 (IP (IP version 4))
= 0
= 0
= 32
PIM: Mask length
PIM: Group multicast address = [225.1.1.1]
Debugging C-RP-Adv
The commands below should be issued on the BSR since the packets are directed to it, other possibility is
to use these commands on the originated C-RP in order to identify if the advertisement are really sent.
-> ip pimsm debug-type crp
-> ip pimsm debug-level 100
Debugging output on BSR:
tPimsm-:
Recv. CRP-Adv (RP:192.168.10.3,Prefix Cnt:1, Pri:0) from
192.168.10.3:192.168.11.1 on vlan 1
tPimsm-:
RP : 192.168.10.3 : Prefix: 225.1.1.1 Mask : 255.255.255.255
Information on the C-RP unicast address, number of count, priority and mcast group as well as on which
PIM interface the advertisement has been received can be seen on with this debug command.
OmniSwitch Troubleshooting Guide September 2005
page 16-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C-RP Advertisements
Troubleshooting PIM-SM
Another output from a C-RP advertisement, advertises itself for all multicast groups. All group addresses
are represented by the pair 224.0.0.0 240.0.0.0, which covers 224.0.0.0 up to 239.255.255.255.
tPimsm-:
Recv. CRP-Adv (RP:192.168.10.3,Prefix Cnt:1, Pri:0) from
192.168.10.3:192.168.11.1 on vlan 2
tPimsm-:
RP : 192.168.10.3 : Prefix: 224.0.0.0 Mask : 240.0.0.0
Related CLI Command
To view the set of multicast group address the PIM router wants to participate in issue:
-> show ip pimsm rp-candidate
Group Address
------------------+---------------+--------
225.1.1.1/32 192.168.11.2 enabled
RP Address
Status
page 16-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
RP-SET
RP-SET
An RP-SET contains a set of Candidates-RP IP addresses that want to participate as RP for multicast
group. The RP-SET is derived from the C RP-Advertisements received by the BSR. RP-SETs are adver-
tised by the BSR in a bootstrap message to all PIM SM routers by using the ALL-PIM-ROUTER address
224.0.0.13. It contains details on the each C-RP IP address, the multicast group routers want to participate
and the corresponding priority.
The DR to determine the RP for each group which it has active members uses the RP-SET. The hash func-
tion algorithm, used to select the RP, takes as input the group address and the addresses of the Candidate
RPs and gives as output one RP address to be used. The protocol requires that all routers hash to the same
RP within a domain for the same multicast group.
BOOTSTRAP message to ALL-PIMSM-ROUTER
BSR ID: 192.168.13.1
Group: 225.1.1.1
RP address: 192.168.11.2
Group: 226.1.1.1
RP address: 192.168.12.2
Group: 227.1.1.1
RP address: 192.168.12.2
C-RP for 226.1.1.1
C-RP for 227.1.1.1
192.168.13.101
192.168.13.1
Bootstrap
message
Bootstrap
message
3Com
3Com
3Com
BSR
192.168.12.1
Bootstrap
message
192.168.12.2
192.168.11.1
3Com
C-RP for 225.1.1.1
192.168.11.2
OmniSwitch Troubleshooting Guide September 2005
page 16-13
Download from Www.Somanuals.com. All Manuals Search And Download.
RP-SET
Troubleshooting PIM-SM
Simplified Bootstrap RP-SET Packet Taken on a 192.168.12/24
Network
IP: ----- IP Header -----
IP: Version = 4, header length = 20 bytes
IP: Protocol
= 103 (PIM)
IP: Source address = [192.168.12.1]
IP: Destination address = [224.0.0.13]
PIM: ----- PIM Header -----
PIM: Version
= 2
PIM: Message Type = 4(Bootstrap)
PIM: Hash mask length
PIM: BSR-priority
= 30
= 0
PIM: *** Encoded-Unicast BSR Address ***
PIM: Address family = 1 (IP (IP version 4))
PIM: Encoding type = 0
PIM: Unicast address = [192.168.13.1]
PIM:
PIM: *** Encoded-Group Address # 1 ***
PIM: Address family
PIM: Encoding type
PIM: Reserved
= 1 (IP (IP version 4))
= 0
= 0
= 32
PIM: Mask length
PIM: Group multicast address = [225.1.1.1]
PIM: RP-count-1 = 1
PIM: Fragment RP-count-1 = 1
PIM: Reserved
PIM:
= 0
PIM: *** Encoded-Unicast RP Address # 1 ***
PIM: Address family = 1 (IP (IP version 4))
PIM: Encoding type = 0
PIM: Unicast address = [192.168.11.2]
page 16-14
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
RP-SET
PIM: RP1-Holdtime
= 150 (in seconds)
= 0
= 0
PIM: RP1-Priority
PIM: Reserved
PIM:
PIM: *** Encoded-Group Address # 2 ***
PIM: Address family
PIM: Encoding type
PIM: Reserved
= 1 (IP (IP version 4))
= 0
= 0
= 32
PIM: Mask length
PIM: Group multicast address = [226.1.1.1]
PIM: RP-count-2 = 1
PIM: Fragment RP-count-2 = 1
PIM: Reserved
PIM:
= 0
PIM: *** Encoded-Unicast RP Address # 1 ***
PIM: Address family = 1 (IP (IP version 4))
PIM: Encoding type = 0
PIM: Unicast address = [192.168.12.2]
PIM: RP1-Holdtime
PIM: RP1-Priority
PIM: Reserved
PIM:
= 150 (in seconds)
= 0
= 0
PIM: *** Encoded-Group Address # 3 ***
PIM: Address family
PIM: Encoding type
PIM: Reserved
= 1 (IP (IP version 4))
= 0
= 0
= 32
PIM: Mask length
PIM: Group multicast address = [227.1.1.1]
PIM: RP-count-3 = 1
PIM: Fragment RP-count-3 = 1
PIM: Reserved
PIM:
= 0
OmniSwitch Troubleshooting Guide September 2005
page 16-15
Download from Www.Somanuals.com. All Manuals Search And Download.
RP-SET
Troubleshooting PIM-SM
PIM: *** Encoded-Unicast RP Address # 1 ***
PIM: Address family = 1 (IP (IP version 4))
PIM: Encoding type = 0
PIM: Unicast address = [192.168.12.2]
PIM: RP1-Holdtime
PIM: RP1-Priority
PIM: Reserved
= 150 (in seconds)
= 0
= 0
The RP-Holdtime parameters is the corresponding time the BSR will hold related RP multicast group
information in its table as valid. This parameter is reset to 150 s when a C-RP Advertisement is received at
BSR and originated by the RP in question.
Debugging RP-SET
As mentioned previously, RP-SET are included in Bootstrap messages. Commands to debug RP-SET:
-> ip pimsm debug-type bootstrap
-> ip pimsm debug-level 100
On Non BSR You Should See
tPimsm-:
on vlan 2
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
Received bootstrap message from 192.168.12.1, bsr addr:192.168.13.1
AcceptBSMsg: Contents
AcceptBSMsg: Prefix : 225.1.1.1 Mask : 255.255.255.255
AcceptBSMsg: RP: 192.168.11.2 Priority : 0
AcceptBSMsg: current rplist does exist
AcceptBSMsg: removing timer
AcceptBSMsg: bit already set for indx:1
AcceptBSMsg: Prefix : 226.1.1.1 Mask : 255.255.255.255
AcceptBSMsg: RP: 192.168.12.2 Priority : 0
AcceptBSMsg: current rplist does exist
AcceptBSMsg: removing timer
AcceptBSMsg: bit already set for indx:2
AcceptBSMsg: Prefix : 227.1.1.1 Mask : 255.255.255.255
AcceptBSMsg: RP: 192.168.12.2 Priority : 0
AcceptBSMsg: current rplist does exist
AcceptBSMsg: removing timer
AcceptBSMsg: bit already set for indx:2
AcceptBSMsg: check Rehash
CheckRehash : SET adding rp:indx:1
CheckRehash : SET adding rp:indx:2
This output shows the IP address of the routing relaying the bootstrap message, the BSR ID, the VLAN
ID, the various multicast group, RP IP address and priority.
Issuing the same command on the BSR would detail the C-RP Advertisement received, and the bootstrap
messages sent on various interfaces.
page 16-16
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
RP-SET
Related CLI Command
To View RP-SET on a router, use the show ip pimsm rp-set command. For example:
-> show ip pimsm rp-set
Group Address
Address
Holdtime Expires
------------------+---------------+--------+-----------
225.1.1.1/32
226.1.1.1/32
227.1.1.1/32
192.168.11.2
192.168.12.2
192.168.12.2
150
150
150
00h:00m:00s
00h:00m:00s
00h:00m:00s
OmniSwitch Troubleshooting Guide September 2005
page 16-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Join/Prune
Troubleshooting PIM-SM
Join/Prune
Join/Prune messages are sent by the DR to join or prune a branch off the multicast distribution tree in
order to receive multicast group on a specific LAN segment that has active group members. Registration
of the members is achieved with IGMP host membership report. Upon reception of such message each
upstream router between the receiver and the RP creates or updates its multicast route entry for specific
multicast group(s) adding interface where join/prune request have been received. When the RP receives
the join/prune message it sends join request toward the sender(s). Refer to user manual under section-
shared tree for drawing and additional protocol details.
A JOIN/PRUNE message contains, the upstream neighbor message, the multicast group address a router
wishes to join, number of joins and pruned source and the RP address.
RECEIVER
225.1.1.1
SENDER
225.1.1.1
IGMP
membership
report 225.1.1.1
192.168.13.1
192.168.15.2
JOIN for 225.1.1.1
DR
3Com
3Com
3Com
DR
BSR
192.168.12.1
192.168.13.101
192.168.12.2
192.168.11.1
JOIN for 225.1.1.1
3Com
RP for 225.1.1.1
192.168.11.2
Simplified Join Packet
IP: ----- IP Header -----
IP: Protocol
= 103 (PIM)
IP: Source address = [192.168.12.2]
IP: Destination address = [224.0.0.13]
page 16-18
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
Join/Prune
PIM: ----- PIM Header -----
PIM:
PIM: Version
= 2
PIM: Message Type = 3(Join/Prune)
PIM: Reserved
PIM: Checksum
PIM:
= 0
= 5794 (correct)
PIM: *** Encoded-Unicast-Upstream Neighbor Address ***
PIM: Address family = 1 (IP (IP version 4))
PIM: Encoding type = 0
PIM: Unicast address = [192.168.12.1]
PIM: Reserved
PIM: Number of groups
PIM: Hold time
PIM:
= 0
= 1
= 210 (in seconds)
PIM: *** Group # 1 ***
PIM:
PIM: *** Encoded-Multicast Group Address-1 ***
PIM: Address family
PIM: Encoding type
PIM: Reserved
= 1 (IP (IP version 4))
= 0
= 0
= 32
PIM: Mask length
PIM: Group multicast address = [225.1.1.1]
PIM: Number of joined sources = 1
PIM: Number of pruned sources = 0
PIM:
PIM: *** Encoded-Joined Source Address # 1 ***
PIM: Address family = 1 (IP (IP version 4))
PIM: Encoding type = 0
PIM: Reserved
PIM: Flags
PIM:
= 0
= 07
.... .1.. = Sparse bit - PIM-SM
OmniSwitch Troubleshooting Guide September 2005
page 16-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Join/Prune
Troubleshooting PIM-SM
PIM:
PIM:
.... ..1. = WC bit - join / prune applies to the (*,G) or (*,*,RP) entry
.... ...1 = RPT-bit - information about (S,G) is sent towards the RP
PIM: Mask length = 32
PIM: Source address = [192.168.11.2]
Simplified PRUNE Packet
The main difference between a JOIN and PRUNE is the number of joined source versus pruned source:
PIM: *** Encoded-Multicast Group Address-1 ***
PIM: Address family
PIM: Encoding type
PIM: Reserved
= 1 (IP (IP version 4))
= 0
= 0
= 32
PIM: Mask length
PIM: Group multicast address = [225.1.1.1]
PIM: Number of joined sources = 0
PIM: Number of pruned sources = 1
Debugging JOIN/PRUNE Event
The commands below will allow you to see any JOIN/PRUNE message:
-> ip pimsm debug-type joinprune
-> ip pimsm debug-level 100
That will show if the message is join or prune, the upstream router, outgoing VLAN, the multicast group
and the RP.
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
tPimsm-:
BuildJoinPrune: for nbr:192.168.12.1 on vlan:2
BuildJoinPrune: next route
Sending Triggered GJoins Joins 1 Prunes 0
BuildJoinPrune: for nbr:192.168.12.1 on vlan:2
BuildJoinPrune: next route
BuildJoinPrune: (*,225.1.1.1) route
BuildJoinPrune: next route
Send Join (192.168.11.2,225.1.1.1) on vlan 2,bits:7 holdtime 210
BuildJoinPrune: for nbr:192.168.12.1 on vlan:2
BuildJoinPrune: next route
BuildJoinPrune: (*,225.1.1.1) route
BuildJoinPrune: next route
Send Join (192.168.11.2,225.1.1.1) on vlan 2,bits:7 holdtime 210
page 16-20
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
Register
Register
When a source starts transmitting to a multicast group, the DR on the segment encapsulates the data and
sends it as unicast to the RP representing the group. The source IP address will be the DR and the destina-
tion IP address will be the RP. Two behaviors are possible:
1-The RP joins the source tree by sending a PIM join to the DR. Packets will then flow from the source to
the RP unencapsulated.
2-The RP does not join the source tree. The multicast packets will be encapsulated by the DR and send to
the unicast address of the RP.
Upon reception of the multicast stream, the RP forwards the packets unencapsulated to receivers if any. If
there are no receivers the RP issues a REGISTER STOP message to the source.
SOURCE
225.1.1.1
192.168.13.1
BSR
3Com
3Com
3Com
DR
192.168.12.1
192.168.13.101
192.168.12.2
192.168.11.1
REGISTER for
225.1.1.1
3Com
RP for 225.1.1.1
192.168.11.2
OmniSwitch Troubleshooting Guide September 2005
page 16-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Register
Troubleshooting PIM-SM
Simplified REGISTER Packet Format
IP: ----- IP Header -----
IP: Source address
= [192.168.13.1]
IP: Destination address = [192.168.11.2]
PIM: ----- PIM Header -----
PIM: Version
= 2
PIM: Message Type = 1(Register)
PIM: Reserved
PIM: Checksum
PIM: Reserved
PIM: Flags
= 0
= deff (should be 45b5)
= 0
= 00
PIM:
PIM:
0... .... = Border bit - router is a DR for a source that i
.0.. .... = Null-Register bit - DR not probing the RP
PIM: Multicast data packet
page 16-22
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
Shared Tree
Shared Tree
A shared distribution tree is formed around the RP, from which all traffic is distributed regardless of the
location of the traffic sources. The advantage of shared distribution trees is simple topology on PIM SM
routers. The DR is sending a JOIN message to the RP, and a graft to the SPT. The disadvantage is that the
path between the source and receivers might not be the shortest one, which could introduce delay. The
rendezvous router may also be a traffic bottleneck if there are many high data rate sources. The Source
Path Tree can be called RP TREE too.
MCAST RECEIVER
for 225.1.1.1
MCAST SOURCE
225.1.1.1
MCAST SOURCE
225.1.1.1
OmniSwitch Troubleshooting Guide September 2005
page 16-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Shared Tree
Troubleshooting PIM-SM
Related CLI Command
In order to view the IP multicast routing table as well as source and distribution tree type:
-> show ip pimsm mroute
Group Address Src Address
Assert Assert
Metric expires
Assert Flags
Pref
---------------+------------------+------+-----------+------+-----
225.1.1.1 192.168.14.115/32 0 00h:00m:00s 0 rpt
page 16-24
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
Source-Based Tree
Source-Based Tree
PIM SM protocol allows a DR to build a Shortest Path Tree, which could provide a shortest path toward
the source. It is being referenced as Source Based Tree because the DR closest to the receiver is initiating
the process.
When a PIM SM graft the shared path tree, a counter is initiated for this specific group on the last DR
closest to the receiver that will be incremented every data packet received. Once the data exceeds a config-
ured threshold the router switches over to source based tree mode. A JOIN message is sent directly toward
the source, after the shortest path tree is activated the DR sends a PRUNE message to the RP.
Note. Currently, the threshold cannot be configured from Clips.
MCAST RECEIVER
for 225.1.1.1
DR
PRUNE
225.1.1.1
JOIN
225.1.1.1
MCAST SOURCE
225.1.1.1
OmniSwitch Troubleshooting Guide September 2005
page 16-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Source-Based Tree
Troubleshooting PIM-SM
Related CLI Command
To view the distribution tree issue:
-> show ip pimsm mroute
Group Address Src Address
Assert Assert
Metric expires
Assert Flags
Pref
---------------+------------------+------+-----------+------+-----
225.1.1.1 192.168.14.115/32 0 00h:00m:00s 0 spt
page 16-26
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
Troubleshooting Examples: Limitations
Troubleshooting Examples: Limitations
Incorrect BSR ID
Turn on BSR debugging to view bootstrap messages:
-> ip pimsm debug-type bootstrap
-> ip pimsm debug-level 100
tPimsm-:
on vlan 2
tPimsm-:
Received bootstrap message from 192.168.11.1, bsr addr:192.168.13.1
RPF check failed for bootstrap msg. SA: 192.168.11.1,BSR
:192.168.13.1, vlan 2
tPimsm-:
pimsmBSRStateTransition - Entering with Event TMR State : ELCTD
OperStatus UP
tPimsm-:
BsrTimer Expired. Orig Message No State change
tPimsm-:
pimsmBSRStateTransition - Leaving with Event TMR State : ELCTD
Status UP
tPimsm-:
Sent BS on vlan 2 ipda = 224.0.0.13
An IP unicast routing issue causes this; the receiving router does not have a route entry for 192.16811.1.
Multicast Group Status is Shown as Disabled
-> show ip pimsm rp-candidate
Group Address
RP Address
Status
------------------+---------------+--------
227.1.1.1/32
226.1.1.1/32
192.168.12.2
192.168.12.2
disabled
disabled
This is caused by a missing C-RP address
-> show ip pimsm
Status
= enabled,
BSR Address
= 192.168.13.1,
= 00h:01m:21s,
= 0.0.0.0,
= 30,
= 0,
= 0.0.0.0,
= 150,
= 00h:05m:00s,
= 60,
= 0,
= 210,
= 60,
BSR Expiry Time
CBSR Address
CBSR Mask Length
CBSR Priority
CRP Address
CRP Hold Time
CRP Expiry Time
CRP Interval
CRP Priority
Data Timeout
Join/Prune Interval
Max RPs
= 32,
Probe Time
= 5,
Register Checksum
= header,
Register Suppress Timeout = 60
-> ip pimsm crp-address 192.168.12.2
OmniSwitch Troubleshooting Guide September 2005
page 16-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Examples: Limitations
Troubleshooting PIM-SM
-> show ip pimsm
Status
BSR Address
= enabled,
= 192.168.13.1,
= 00h:01m:43s,
= 0.0.0.0,
= 30,
= 0,
= 192.168.12.2,
= 150,
= 00h:05m:00s,
= 60,
= 0,
= 210,
= 60,
BSR Expiry Time
CBSR Address
CBSR Mask Length
CBSR Priority
CRP Address
CRP Hold Time
CRP Expiry Time
CRP Interval
CRP Priority
Data Timeout
Join/Prune Interval
Max RPs
= 32,
Probe Time
= 5,
Register Checksum
= header,
Register Suppress Timeout = 60
-> show ip pimsm rp-candidate
Group Address
RP Address
Status
------------------+---------------+--------
227.1.1.1/32
226.1.1.1/32
192.168.12.2
192.168.12.2
enabled
enabled
PIM-SM Limitations
Only one C-RP should be configured per PIM domain. Having multiple C-RPs is not currently supported.
The problem with fragmentation and reassembly of PIM-SM tunneled packets (PIM register-encapsulated
packets fall into this category), is if packets need to be fragmented, it might prevent mcast stream to be
delivered properly. A smaller MTU size would work around this issue.
Upstream Neighbor/Next Hop Debug Commands
Use following debug commands to find an upstream neighbor or to verify next hop.
-> debug ip pimsm rpf 172.100.1.254
Source IP Address
RPF Vlan
= 172.100.1.254,
= 100,
RPF Neighbor
= 172.100.1.254,
= 172.100.1.0/24,
= 1,
RPF Route/Mask
RPF Metric Preference
RPF Metric
= 0
-> debug ip pimsm rp-hash 224.0.0.0
Group Address
------------------+------------------
224.0.0.0 172.100.1.254
RP Address
page 16-28
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting PIM-SM
Troubleshooting Examples: Limitations
-> debug ip pimsm rp
Group Address
RP Address
------------------+------------------
224.0.1.22
224.0.1.24
239.0.0.90
239.1.1.200
239.1.1.201
239.1.1.202
239.255.255.254
172.100.1.254
172.100.1.254
172.100.1.254
172.100.1.254
172.100.1.254
172.100.1.254
172.100.1.254
OmniSwitch Troubleshooting Guide September 2005
page 16-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Examples: Limitations
Troubleshooting PIM-SM
page 16-30
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
17 Troubleshooting Server
Load Balancing
In order to successfully troubleshoot the Alcatel Server Load Balancing feature, a brief understanding of
this services functions are necessary.
Our Basic Definition
The “Server Load Balancing” (SLB) term used in this document refers to the functionality of distributing
client requests across servers logically grouped in “clusters.”
A “cluster” logically aggregates a set of servers that run identical applications with access to the same
content (e.g. a Web server).
Points to Remember
• Each cluster’s Virtual IP address (VIP) is seen by clients
• 15 clusters are supported per switch
• Each cluster can have up to 5 servers
Note. The Alcatel OmniSwitch 7700/7800/8800 supports two different types of SLB distribution algo-
rithms. Reading “Configuring Server Load Balancing” in the OmniSwitch 7700/7800/8800 Network
Configuration Guide for a more detailed explanation of these algorithms is highly recommended.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 17-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Troubleshooting Server Load Balancing
Introduction
The primary function of a Server Load Balance cluster is to provide a method to logically treat a group of
physical servers (known as a server farm) as one large virtual server (known as an SLB cluster).
Note. This document does not discuss the basic operation of Server Load Balancing. To learn about how
SLB works, refer to “Configuring Server Load Balancing” in the OmniSwitch 7700/7800/8800 Network
Configuration Guide.
This document assumes the reader has knowledge of the Server Load Balance operation.
In the following pages we will discuss:
• How to determine a Server Load Balance failure
• Troubleshooting a Server Load Balance Failure
Server Load Balance Failure
What is an SLB Failure?
A failure in the Alcatel Server Load Balance feature will appear in 1 of 2 forms. We will discuss these two
forms in the following paragraphs:
• Complete failure of service
• Partial failure of service
Description of a Complete Failure of Service
A complete failure of service is best described as a loss of connectivity to all servers for all users. This can
be verified by a simple connectivity test (ping) to the SLB cluster Virtual IP (SLB VIP).
Description of a Partial Failure of Service
A partial failure of service is best described as a condition where the traffic distribution rules are not being
adhered to, but cluster connectivity is still present.
page 17-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Server Load Balancing
Troubleshooting Commands
Troubleshooting Commands
Below is a list of commands, which will be used and discussed in this chapter.
show ip slb (Displays SLB information)
show ip slb cluster-name
For example:
-> show ip slb cluster Intranet
Cluster Intranet
VIP
: 128.241.130.205,
: Enabled,
: In Service,
Admin status
Operational status
Routed flows success ratio (%) = 100,
Ping period (seconds)
Ping timeout (milliseconds)
Ping retries
= 60,
= 3000,
= 3,
Redirect algorithm
Sticky time (seconds)
Number of flows
: round robin,
= 600,
= 45768,
= 2
Number of servers
Server 128.220.40.4
Admin status = Enabled, Operational Status = In Service,
Weight = 10, Number of flows = 2000, Availability (%) = 98
Server 128.220.40.5
Admin status = Enabled, Operational Status = Discovery,
Weight = 10, Number of flows = 0, Availability (%) = 0
ip slb admin {enable | disable} (Enables or disables the SLB service)
ip slb cluster cluster-name admin status {enable | disable}
ip slb cluster cluster-name distribution {round robin | server failover}
[no] ip slb server ip ip-address
For example:
-> show ip slb
Admin status
Operational status
Number of clusters
: Enabled,
: In Service,
= 3
Viewing data of all clusters:
show ip slb clusters
For example:
-> show ip slb clusters
Admin
Operational
#
%
Cluster Name VIP
Status Status
Srv Avail
----------------+----------------+--------+-------------------+-----+---------
WorldWideWeb 128.241.130.204 Enabled In Service
Intranet 128.241.130.205 Enabled In Service
FileTransfer 128.241.130.206 Enabled Out of Service
3
2
2
95
100
50
OmniSwitch Troubleshooting Guide September 2005
page 17-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting a Complete Failure
Troubleshooting Server Load Balancing
Troubleshooting a Complete Failure
Gathering pertinent information is essential in order to properly characterize the problem. Obtain symp-
tom facts, review all recent network or architecture changes, localize the problem, e.g. does it affect only
certain floors, or departments? Devise an action plan.
The first step in any troubleshooting process is to gather information. The more information you have
about the symptoms and characteristics of a problem, including when it first occurred, the better your
chances of solving the problem quickly and efficiently. Typical questions you might ask at this stage
before beginning to troubleshoot spanning tree include:
• Do the symptoms occur regularly or intermittently?
• Are the symptoms related to certain applications (running simultaneously with), or do they affect all
network operations?
• Are other SLB clusters located on this switch malfunctioning?
• How many users are involved?
• Do the symptoms correlate to other activities in the network?
• When was the first occurrence of the symptom?
• Were there any changes in any hardware or software network components?
• Has anyone connected or disconnected a PC (laptop or desktop), or another component to or from the
network?
• Has anyone installed an interface card in a computer/server?
• Has DHCP possibly provided a lease to a user with the SLB VIP?
• Has anyone stepped on a cable?
• Has any maintenance work been performed in the building recently (by a telephone company or build-
ing maintenance personnel, for example)?
• Has anyone (including cleaning personnel) moved/unplugged any equipment or furniture?
Note. In general, it is advised to restart a device immediately after major changes have been made to it;
you want to make sure that all your changes have been saved. You also want to verify that after a reboot
(equivalent to a power outage or a crash), the device will come up with the correct and complete configu-
ration.
page 17-4
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Server Load Balancing
Troubleshooting a Partial Failure
Troubleshooting a Partial Failure
The number one cause of a partial failure is misconfiguration. In the following area, we will show you
how to determine the SLB configuration.
The Troubleshooting Procedure
If you have reason to believe that the SLB cluster is operational, however inaccessible, Alcatel’s 7700/
7800/8800 provides useful commands for narrowing down the problem.
One of the most useful commands used in troubleshooting SLB problems on the 7700/7800/8800 product
line is the show ip slb clusters command.
For example:
-> show ip slb clusters
Admin
Status Status
----------------+----------------+--------+-------------------+-----+---------
Operational
#
%
Cluster Name VIP
Srv Avail
WorldWideWeb 128.241.130.204 Enabled In Service
Intranet 128.241.130.205 Enabled In Service
FileTransfer 128.241.130.206 Enabled Out of Service
3
2
2
95
100
50
As shown in the example above, this command will provide pertinent information in verifying which
server cluster(s) are inaccessible or malfunctioning.
After you have determined which SLB cluster is not accessible, performing the show ip slb cluster
cluster-name command will provide more detailed information on the configuration and status of the
above named SLB cluster.
The show active policy rule and show policy condition commands are also useful when troubleshooting
SLB problems:
-> show active policy rule
Policy
From Prec Enab Act Refl Log Save Matches
SLB-rule-FTP
( L3):
api 65000 Yes Yes No No Yes
SLB-cond-FTP -> SLB-act-FTP
7
-> show policy condition
Condition Name
SLB-cond-FTP
From
api
Src -> Dest
*IP
:
Any -> 172.160.1.100
OmniSwitch Troubleshooting Guide September 2005
page 17-5
Download from Www.Somanuals.com. All Manuals Search And Download.
The Troubleshooting Procedure
Troubleshooting Server Load Balancing
page 17-6
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Troubleshooting
Authenticated VLANs
In order to troubleshoot Authenticated VLAN (AVLAN), a basic understanding of how authentication
works in the switch is required. Understanding of Radius and DHCP server will be useful in troubleshoot-
ing Authenticated VLAN.
Note. Reading the “Managing Authentication Servers” and the “Configuring Authenticated VLANs”
chapters in the appropriate OmniSwitch Network Configuration Guide is highly recommended.
In This Chapter
Introduction
The main function of Authenticated VLAN is to control user access to network resources based on VLAN
assignment and user login process. This process is sometimes called user authentication or Layer 2
Authentication. The term Authenticated VLANs (AVLANs) and Layer 2 Authenticaion are synonymous.
Note. This document does not discuss the basic operation of the AVLAN. To learn about how AVLAN
works, refer to the “Managing Authentication Servers” and the “Configuring Authenticated VLANs”
chapters in the appropriate OmniSwitch Network Configuration Guide.
OmniSwitch Troubleshooting Guide September 2005
page 18-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting AVLAN
Troubleshooting Authenticated VLANs
Troubleshooting AVLAN
DHCP Request Failure
If the client (PC-1) is configured to get the DHCP IP address and can not get DHCP address during the
first phase of authentication process, it could be because of wrong configuration in the switch, communi-
cation failure or miss configured DHCP server.
Use the command:
-> show ip helper
This command is to verify IP addresses for DHCP servers that will receive BOOTP/DHCP packets
forwarded by this UDP Relay service is set correctly. The example of command output is shown below:
-> show ip helper
Forward Delay(seconds) = 3,
Max number of hops = 4,
Forward option = standard
Forwarding Address:
192.168.10.100
In addition with IP helper address, verify that the Gateway of the DHCP server is correctly specified. The
Gateway is a router port in any of the authenticated VLANs in the switch. It specifies the scope into which
an authentication client receives an IP address.
-> show aaa avlan config
default DHCP relay address = 192.168.10.1,
authentication DNS name
= not configured
If the IP address for the DHCP server is set correctly then try to ping the server to verify the connectivity.
You can also verify the MAC-address-table and ARP table entries.
-> show mac-address-table
The mac-address-table CLI command confirms that the switch has learned the MAC address of the DHCP
server has been learned.
-> show mac-address-table
Legend: Mac Address: * = address not valid
Vlan
------+-------------------+--------------+-----------+------------+-----------
00:c0:4f:0c:3a:e4 learned bridging 1/21
Mac Address
Type
Protocol
Operation
Interface
2
0
Total number of Valid MAC addresses above = 1
Now verify that the Gateway defined in DHCP server point towards the right IP address. ARP table
confirms that the switch has learned the ARP entry of the DHCP server. Verify that the IP address of the
DHCP server has been learned in the correct VLAN and the port it has been attached.
-> show arp
Total 1 arp entries
Flags (P=Proxy, A=Authentication, V=VRRP)
IP Addr
Hardware Addr
Type
Flags Port
Interface
-----------------+-------------------+----------+-------+--------+-----------
page 18-2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Authenticated VLANs
Troubleshooting AVLAN
192.168.10.100
00:c0:4f:0c:3a:e4 DYNAMIC
1/21 vlan 2
There are couples of other things you can verify is on the DHCP server itself.
• Router IP address is set to the IP address of one of the authenticated VLANs in the switch.
• Address pool must be created in order to assign the DHCP IP address.
Authentication Failure
If the client (PC-1) is cannot successfully completes the authentication, it could be because of wrong
configuration in the switch, communication failure or miss configured RADIUS server.
Use the command:
-> show aaa server
1 Verify that the correct IP address of the radius server has been entered. The Authentication port and
Accounting port must match with the Radius server’s port configuration.
To verify the port configuration on the radius server open the radius.ini file in Notepad and check for
below entries.
• [Ports]
• UDPAuthPort = 1812
• UDPAcctPort = 1813
You can also use UDPAuthPort = 1645 and UDPAcctPort = 1646 if you want. It’s ok to use these ports
based on old RFC. Whatever is there it should be same on both Switch and the Server.
The example of the show aaa server CLI command is shown below:
-> show aaa server
Server name = rad-1
Server type
= RADIUS,
= 192.168.10.100,
= 3,
IP Address 1
Retry number
Time out (sec)
= 2,
Authentication port = 1812,
Accounting port = 1813
To modify any of the above fields use the aaa radius-server CLI command. For detail reference of how
to set such parameters, read the “Managing Authentication Servers” and the “Configuring Authenticated
VLANs” chapters in the appropriate OmniSwitch Network Configuration Guide.
2 Ping the radius server to verify the good connectivity. If server doesn’t respond, fix the connectivity
issue first and then troubleshoot Authentication configuration.
3 You can also verify the MAC address-table and ARP table entries.
-> show mac-address-table
The MAC address table confirms that the switch has learned mac-address of the RADIUS server has been
learned.
OmniSwitch Troubleshooting Guide September 2005
page 18-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting AVLAN
Troubleshooting Authenticated VLANs
-> show mac-address-table
Legend: Mac Address: * = address not valid
Vlan
Mac Address
Type
Protocol
Operation
Interface
------+-------------------+--------------+-----------+------------+-----------
2 00:c0:4f:0c:3a:e4
learned
0
bridging
1/21
Total number of Valid MAC addresses above = 1
Now verify that the Gateway defined in RADIUS server point towards the right IP address. ARP table
confirms that the switch has learned the ARP entry of the RADIUS server. Verify that the IP address of
the RADIUS server has been learned in the correct VLAN and the port it has been attached.
-> show arp
Total 1 arp entries
Flags (P=Proxy, A=Authentication, V=VRRP)
IP Addr
-----------------+-------------------+----------+-------+--------+-----------
192.168.10.100 00:c0:4f:0c:3a:e4 DYNAMIC 1/21 vlan 2
Hardware Addr
Type
Flags Port
Interface
4 Verify that the Authentication shared secret on the radius server and the switch (Radius client) is same.
There is no show command to check the Authentication shared secret on the switch for the security
purpose. The only way to verify is reenter the shared secret using the aaa radius-server CLI command
5 If so far so good and radius server is rejecting user request, verify the user configuration on the radius
server to make sure he/she is using correct user name and password. Read the the “Managing Authentica-
tion Servers” chapter in the appropriate OmniSwitch Network Configuration Guide for detail information
about Radius server attributes and configuration. Check log file on the radius server for more information.
Problem Communicating Using Multiple Protocols
Simultaneously
If client can’t communicate to the remote station in the Authenticated VLAN using multiple protocols
simultaneously then check below possible configuration mistakes.
Let’s take an example of user who is trying to communicate to the target machine using both IP and IPX.
The communication might failure because of one or more of the following steps.
1 If client can’t communicate using IP and IPX, troubleshoot the basic authentication issues using the
procedures described in “DHCP Request Failure” on page 18-2 and “Authentication Failure” on page 18-3
explained earlier in this chapter.
2 If authentication works fine using IP not IPX then troubleshoot the Radius Server as explained in next
steps.
3 Locate Alcatel.dct file under Radius installed folder on the Radius Server. Open this file using Note-
pad and look for the ATTRIBUTE “Alcatel-Auth-Group-Protocol”. If you don’t see this attribute then
contact Alcatel Customer Support to get the latest Alcatel.dct (Alcatel Dictionary) file. Replace it with the
new one.
4 Once the new file is in place make sure you associate multiple protocol with the Authenticated VLAN
that user moving into. Refer to the “Managing Authentication Servers” chapter in the appropriate
OmniSwitch Network Configuration Guide for Vendor-Specific Attributes for RADIUS.
page 18-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Authenticated VLANs
Troubleshooting Using Debug Systrace
Useful Notes on Client Issues
• If using telnet authentication manual IP release and renew required getting the new IP after authentica-
tion.
Troubleshooting Using Debug Systrace
Telnet Authentication and De-authentication
Do not change the aaaDebugFunction flag under Dshell, keep it the default setting.
In addition with that use below commands to capture maximum debug information:
-> debug systrace no appid all
-> debug systrace appid 20 level debug3
-> debug systrace watch enable
After gathering all information disable the systrace using below command.
-> debug systrace watch disable
The best way to troubleshoot is to verify the working and non-working case. Compare the results of both
cases and find the possible point of failure.
Get the IP Address from Default VLAN
-> 2356669885 AAA
2356670006 AAA
2356670145 AAA
2358821890 AAA
debug3 entering in aaaProcessPortManager
debug3 rec from PM 1, status ad UP, op UP
debug2 [ONEX] onex_process_pm LINK_STATUS 1002
debug1 begin Authent Evt : Req, St : IDLE, name : admin, Rec
ses :
0/ 1(TRUNCATED)
2358822025 AAA
2358822084 AAA
2359129753 AAA
2359130018 AAA
2359130099 AAA
2359130170 AAA
link
debug3 Entering in aaaAuthentReq
debug3 Entering in aaa_ProcessAuthent
debug3 Entering in aaa_ReplyHdlMgt
debug1 Send auth Success, session
0
debug3 Entering in aaa_userReturnST_IDLE
debug1 AAA_Serv>> Ctx admin removed from No link, set in No
2359130247 AAA
Ret = OK
debug1 End Authent Evt St : IDLE, name : , ses :
debug3 AAA_Serv>> sort aaaSortUserCtx
debug3 Ip Address not in same Vlan than Default Dhcp Gateway
debug1 Send a DHCP Release to DHCP Server 133.2.253.1
debug2 op=1, htype=1, hlen=6, hops=0, xid=1
0/ 0,
2360615756 AAA
2362006927 AAA
2362007048 AAA
2362007107 AAA
2362007164 AAA
yiaddr=0.0.0.0
2362007226 AAA
debug2 secs=0, flags=0x00000000, ciaddr=172.31.21.161,
debug2 siaddr=0.0.0.0, giaddr=0.0.0.0,
chaddr=00:90:27:75:dc:a2
2362007271 AAA
2362007490 AAA
debug2 sname=<>file=<>
debug1 DHCP Release sent successfully
->
OmniSwitch Troubleshooting Guide September 2005
page 18-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Using Debug Systrace
Troubleshooting Authenticated VLANs
Initiate the Telnet Authentication
-> 2394037098 AAA
2394037225 AAA
2394037384 AAA
2394037565 AAA
debug1 Send AAA_HDL_MGT_USER_REQ
debug1 Message succefully sent
debug3 Entering in aaa_ProcessHdlMsg
debug1 AVLAN begin Evt : Req,St : IDLE, name : Avlan ses
0x60008 00.00.00.00.00.00
2394037621 AAA
2394037675 AAA
2394037721 AAA
2394037768 AAA
2394080316 AAA
debug3 aaaAvlanUserReq ses rec 0x3ef, Avlan ses 0x60008
debug1 Ctx admin removed from No link, set in MAC link
debug3 aaaAvlanFormatSendAuthReq
debug1 Send Auth. Req. to AAA name : admin, Avlan ses 60008
debug12394080448 AVLAAAAN end St : WAIT
RESP, name :
admin, Ret = OKdebug1 begin Authent Evt : Req, St : IDLE, name : admin, Rec ses
: 60008/ (TRUNCATED)
2394277037 AAA
2394321109 AAA
2394385614 AAA
2394451209 AAA
0x1e0020
debug3 Entering in aaaAuthentReq
debug3 Entering in aaa_ProcessAuthent
debug3 Entering in aaa_FormatSendAuthReq
debug1 Send Auth/Log to RADIUS for admin, Refser:0x2 AAA ses
23945393902394539440 AAAAAA
from N[RAD] radMain : messo link, set in Chal_age received from AARsp linkA
23947124523947125147 AAAAAA debug1info End Authent Evt St : WAIT
debug1deb ug3AAA_Serv>> Ctx a dmin removed
RESP1, name :[RAD] Message Authen admin, ses : 60008/tication Request - m 7,
Ret = OKsgID = 140026 - received from(TRUNCATED)
2394930753 AAA
2394997268 AAA
2395083317 AAA
2395148871 AAA
0x8502fdfc
info [RAD] radBuildServeurAuth : id = 7
info [RAD] radAddAttr : adding attribute type 1
info [RAD] radAddAttr : adding attribute type 2
info [RAD] radBuildServeurAuth : RADIUS client address =
2395234856 AAA
2395323003 AAA
2395387501 AAA
2395474782 AAA
try=1
info [RAD] radAddAttr : adding attribute type 4
info [RAD] radAddAttr : adding attribute type 5
info [RAD] rad_buildauth: port 1 added to access-request
info [RAD] radDoSend OK : id=7, addr=0x8502fd01 port=1645
2395562721 AAA
try=1
2395671413 AAA
info [RAD] radDoSend OK : id=7, addr=0x8502fd01 port=1645
debug3 [RAD] radProcPkt: Got a reply from Radius server , id =
7, code 2, length 59
2395779908 AAA
2395845441 AAA
rcvd.
info [RAD] radProcPkt: Attribute type 25, length 27
info [RAD] radProcPkt: classe (_SBR-CL DN="ADMIN" AT="0"_)
2395955105 AAA
2396019598 AAA
length 6
info [RAD] radProcPkt: Attribute type 26, length 12
info [RAD] radProcPkt: Xylan-specific attribute type 1,
2396106681 AAA
protobind=0
2396216328 AAA
(admin)
info [RAD] radAddAuthGroup :numOfVlans=1, groupeNbr=103,
info [RAD] radProcPkt: RADIUS authentication succeeded
info [RAD] radSendMsgToAaa : message Authentication Reply -
2396302335 AAA
msgID = 140046(TRUNCATED)
2396412150 AAA
2396499091 AAA
debug3 in aaa_DispatchClientRsp,msgId=0x140046
debug1 begin Authent Evt : Auth Reply Ok, St : WAIT RESP1,
name : admin, Rec(TRUNCATED)
2396607639 AAA
2396650688 AAA
2396716214 AAA
debug3 Entering in aaa_AuthRspOK
debug3 Entering in aaa_ReplyHdlMgt
debug1 Send auth Success, session 60008
23967818172396781906 AAAAAA
debug1debug3 AVLAN begin Evt : AEntering in
aaa_useruth Reply Ok,St : WAReturnST_IDLEIT RESP, name : admin Avla2396933365n
se(TRUNC ATED)AAA 2396977 445debug1 AAAAAA_S erv>> Ctx admin r emoved from
page 18-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Authenticated VLANs
Troubleshooting Using Debug Systrace
Chal_Rsdebug3p link, set in No linkEntering in aaaAvlanAuthRspOK2
3971075352397129005 AAAAAA
debudebug3g1 AAA_Serv>>End Authent Evt St
:entering in aaaAvla IDLE, name : , ses nSendOneCtxToSeconda:
OryCmm K
0/ 0, Ret =
2397304273 AAA
2397391330 AAA
2397455810 AAA
Avlan ses 0x60008
2397544001 AAA
2397630062 AAA
2397696619 AAA
2397761123 AAA
2397847134 AAA
debug2 SL 0xa0070 00.90.27.75.dc.a2, VL 103, proto 1 p 1
debug3 Entering in aaaAvlanReplyHdlMgt
debug1 Send Authent. Success, name : admin, hdl ses 0x3efx
debug2 Ask stat user admin ref 0x516bcf0 00.90.27.75.dc.a2
debug3 Entering in aaaAvlanFormatSendAcct
debug1 Send login Acct Evt to AAA admin, 103
debug1 AVLAN end St : CONNECTED, name : admin, Ret = OK
debug2 Receiv. stat user admin ref 0x60008 00.90.27.75.dc.a2
Release/Renew IP
ERROR: Invalid entry: "RElease/Renew"
-> 2422393032 AAA
2422393140 AAA
2422393204 AAA
yiaddr=0.0.0.0
2422393266 AAA
debug1 Send a DHCP Release to DHCP Server 133.2.253.1
debug2 op=1, htype=1, hlen=6, hops=0, xid=1
debug2 secs=0, flags=0x00000000, ciaddr=10.0.1.150,
debug2 siaddr=0.0.0.0, giaddr=0.0.0.0,
chaddr=00:90:27:75:dc:a2
2422393311 AAA
2422393554 AAA
debug2 sname=<>file=<>
debug1 DHCP Release sent successfully
De-Authenticating
-> 2450771829 AAA
2450771954 AAA
2450772220 AAA
2450772284 AAA
2450772346 AAA
2450772540 AAA
debug1 Send AAA_HDL_MGT_LOGOUT_REQ
debug1 Message succefully sent
debug3 Entering in aaa_ProcessHdlMsg
debug3 Entering in aaaAvlanReplyHdlFailNoCtx
debug1 Send authent. Failure session 3f0
debug1 AVLAN begin Evt : Logout Usr,St : CONNECTED, name :
admin Avlan ses 0(TRUNCATED)
2450772591 AAA
2450772654 AAA
2450793571 AAA
2450880635 AAA
2450968891 AAA
2451055841 AAA
2451121440 AAA
2451230029 AAA
2451317046 AAA
2451383711 AAA
2451449301 AAA
2451492283 AAA
debug3 Entering in aaaAvlanLogHdlPerf1
debug2 SL 0xa0071 00.90.27.75.dc.a2, VL 103, proto 1 p 1
debug3 AAA_Serv>> entering in aaaAvlanSendOneCtxToSecondaryCmm
debug2 Ask stat user admin ref 0x516bcf0 00.90.27.75.dc.a2
debug1 Ctx admin removed from MAC link, set in Account. link
debug1 AVLAN end St : CONNECTED, name : admin, Ret = OK
debug2 Rec Fr SL Del 00.90.27.75.dc.a2, VL 103, p 1, prot = 0
debug2 Receiv. stat user admin ref 0x60008 00.90.27.75.dc.a2
debug3 Entering in aaaAvlanFormatSendAcct
debug1 Send logout Acct Evt to AAA admin, 103
debug3 in aaaAvlanReturnST_IDLE
debug1 Ctx admin removed from Account. link, set in No link
Release/Renew to Go Back to Default VLAN
ERROR: Invalid entry: "Release/Renew"
-> 2476994772 AAA
way
debug3 Ip Address not in same Vlan than Default Dhcp Gate-
2476994902 AAA
2476994961 AAA
2476995017 AAA
yiaddr=0.0.0.0
2476995079 AAA
debug1 Send a DHCP Release to DHCP Server 133.2.253.1
debug2 op=1, htype=1, hlen=6, hops=0, xid=1
debug2 secs=0, flags=0x00000000, ciaddr=172.31.21.161,
debug2 siaddr=0.0.0.0, giaddr=0.0.0.0,
OmniSwitch Troubleshooting Guide September 2005
page 18-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Using Debug Systrace
Troubleshooting Authenticated VLANs
chaddr=00:90:27:75:dc:a2
2476995124 AAA
2476995365 AAA
2477000684 AAA
debug2 sname=<>file=<>
debug1 DHCP Release sent successfully
debug3 AAA_Serv>> sort aaaSortUserCtx
HTTP/S Authentication
Start of Authentication using https://x.x.x.253
-> 2163508216 AAA
2163508471 AAA
debug3 Entering in aaa_ProcessHdlMsg
debug1 AVLAN begin Evt : Req,St : IDLE, name : Avlan ses
0x9000b 00.00.00.00.00.00
2163508527 AAA
2163508584 AAA
2163508629 AAA
2163508839 AAA
2163508921 AAA
2163509108 AAA
debug3 aaaAvlanUserReq ses rec 0x5a22bc0, Avlan ses 0x9000b
debug1 Ctx admin removed from No link, set in MAC link
debug3 aaaAvlanFormatSendAuthReq
debug1 Send Auth. Req. to AAA name : admin, Avlan ses 9000b
debug1 AVLAN end St : WAIT RESP, name : admin, Ret = OK
debug1 begin Authent Evt : Req, St : IDLE, name : admin, Rec
ses : 9000b/ (TRUNCATED)
2163638516 AAA
2163682571 AAA
2163747084 AAA
2163812695 AAA
0x2e0030
debug3 Entering in aaaAuthentReq
debug3 Entering in aaa_ProcessAuthent
debug3 Entering in aaa_FormatSendAuthReq
debug1 Send Auth/Log to RADIUS for admin, Refser:0x2 AAA ses
21639008772163900923 AAAAAA
messtx admin removed froage received from AAm No link, set in ChAal_Rsp link
21640721640750534983 AAAA AA debug1 infEnd Authent Evt St :o WAIT
debug1debug3 AAA_Serv>> C[RAD] radMain :
RESP1,name : admin, ses : 9000 b/ 8, Ret = OK[RAD] Message Authentication
Request - msgID = 140026 - received from(TRUNCATED)
2164292241 AAA
2164357668 AAA
2164444794 AAA
2164510338 AAA
0x8502fdfc
info [RAD] radBuildServeurAuth : id = 10
info [RAD] radAddAttr : adding attribute type 1
info [RAD] radAddAttr : adding attribute type 2
info [RAD] radBuildServeurAuth : RADIUS client address =
2164617813 AAA
2164681287 AAA
2164768333 AAA
2164833038 AAA
try=1
info [RAD] radAddAttr : adding attribute type 4
info [RAD] radAddAttr : adding attribute type 5
info [RAD] rad_buildauth: port 1 added to access-request
info [RAD] radDoSend OK : id=10, addr=0x8502fd01 port=1645
2164942484 AAA
try=1
2165029680 AAA
info [RAD] radDoSend OK : id=10, addr=0x8502fd01 port=1645
debug3 [RAD] radProcPkt: Got a reply from Radius server , id =
10, code 2, length 59
2165138155 AAA
2165225209 AAA
rcvd.
info [RAD] radProcPkt: Attribute type 25, length 27
info [RAD] radProcPkt: classe (_SBR-CL DN="ADMIN" AT="0"_)
2165313348 AAA
2165400417 AAA
length 6
info [RAD] radProcPkt: Attribute type 26, length 12
info [RAD] radProcPkt: Xylan-specific attribute type 1,
2165487500 AAA
protobind=0
2165573496 AAA
(admin)
info [RAD] radAddAuthGroup :numOfVlans=1, groupeNbr=103,
info [RAD] radProcPkt: RADIUS authentication succeeded
info [RAD] radSendMsgToAaa : message Authentication Reply -
2165682084 AAA
msgID = 140046(TRUNCATED)
2165791914 AAA
2165856331 AAA
debug3 in aaa_DispatchClientRsp,msgId=0x140046
debug1 begin Authent Evt : Auth Reply Ok, St : WAIT RESP1,
page 18-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Authenticated VLANs
Troubleshooting Using Debug Systrace
name : admin, Rec(TRUNCATED)
2165965890 AAA
2166030420 AAA
2166095975 AAA
2166161550 AAA
debug3 Entering in aaa_AuthRspOK
debug3 Entering in aaa_ReplyHdlMgt
debug1 Send auth Success, session 9000b
debug32166161654 EntAAAering in aaa_user
ReturnST_IDLEde2166227153bug1 AAAA VLAN begin Evt : Auth Reply Ok,St :
debug1WAIT RESP, nam e : admin Avlan se(AAA_Serv>> Ctx adminTRUNCATED) removed
from Chal_Rsp link, 2166400173set in No linkAAA 21664443 23debug3 AAAEnteri
ng in aaaAvlanAut hRspOKdebug1 21665End Authent Evt St :08777 IDLE, name : ,
ses :
0/ 0, RAAAet = OK debug3 AAA_Serv>> entering in aaaAvlanSendOneCtxTo-
SecondaryCmm
2166662500 AAA
2166749577 AAA
2166815137 AAA
Avlan ses 0x9000b
2166922686 AAA
2167010902 AAA
2167076367 AAA
2167146149 AAA
2167234431 AAA
2202536369 AAA
2202536483 AAA
2202536546 AAA
yiaddr=0.0.0.0
2202536608 AAA
debug2 SL 0xa0070 00.10.a4.b5.bc.48, VL 103, proto 1 p 1
debug3 Entering in aaaAvlanReplyHdlMgt
debug1 Send Authent. Success, name : admin, hdl ses 0x5a22bc0x
debug2 Ask stat user admin ref 0x516bfa8 00.10.a4.b5.bc.48
debug3 Entering in aaaAvlanFormatSendAcct
debug1 Send login Acct Evt to AAA admin, 103
debug1 AVLAN end St : CONNECTED, name : admin, Ret = OK
debug2 Receiv. stat user admin ref 0x9000b 00.10.a4.b5.bc.48
debug1 Send a DHCP Release to DHCP Server 133.2.253.1
debug2 op=1, htype=1, hlen=6, hops=0, xid=1
debug2 secs=0, flags=0x00000000, ciaddr=10.0.1.151,
debug2 siaddr=0.0.0.0, giaddr=0.0.0.0,
chaddr=00:10:a4:b5:bc:48
2202536653 AAA
2202536871 AAA
debug2 sname=<>file=<>
debug1 DHCP Release sent successfully
De-Authenticate using https://x.x.x.253
-> 2243269618 AAA
2243269736 AAA
2243269809 AAA
2243270033 AAA
debug3 Entering in aaa_ProcessHdlMsg
debug3 Entering in aaaAvlanReplyHdlFailNoCtx
debug1 Send authent. Failure session 4a72618
debug1 AVLAN begin Evt : Logout Usr,St : CONNECTED, name :
admin Avlan ses 0(TRUNCATED)
2243270260 AAA
2243270330 AAA
2243270405 AAA
2243270463 AAA
2243357036 AAA
2243443989 AAA
2243509583 AAA
2243618200 AAA
2243705189 AAA
2243771852 AAA
2243837443 AAA
2243880420 AAA
2252923311 AAA
2252923436 AAA
2252923489 AAA
2252923544 AAA
yiaddr=0.0.0.0
2252923604 AAA
debug3 Entering in aaaAvlanLogHdlPerf1
debug2 SL 0xa0071 00.10.a4.b5.bc.48, VL 103, proto 1 p 1
debug3 AAA_Serv>> entering in aaaAvlanSendOneCtxToSecondaryCmm
debug2 Ask stat user admin ref 0x516bfa8 00.10.a4.b5.bc.48
debug1 Ctx admin removed from MAC link, set in Account. link
debug1 AVLAN end St : CONNECTED, name : admin, Ret = OK
debug2 Rec Fr SL Del 00.10.a4.b5.bc.48, VL 103, p 1, prot = 0
debug2 Receiv. stat user admin ref 0x9000b 00.10.a4.b5.bc.48
debug3 Entering in aaaAvlanFormatSendAcct
debug1 Send logout Acct Evt to AAA admin, 103
debug3 in aaaAvlanReturnST_IDLE
debug1 Ctx admin removed from Account. link, set in No link
debug3 Ip Address not in same Vlan than Default Dhcp Gateway
debug1 Send a DHCP Release to DHCP Server 133.2.253.1
debug2 op=1, htype=1, hlen=6, hops=0, xid=1
debug2 secs=0, flags=0x00000000, ciaddr=172.31.21.160,
debug2 siaddr=0.0.0.0, giaddr=0.0.0.0,
chaddr=00:10:a4:b5:bc:48
2252923648 AAA
2252923886 AAA
2252938688 AAA
debug2 sname=<>file=<>
debug1 DHCP Release sent successfully
debug3 AAA_Serv>> sort aaaSortUserCtx
OmniSwitch Troubleshooting Guide September 2005
page 18-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Using Debug Systrace
Troubleshooting Authenticated VLANs
AVClient
AVClient Authentication Start
-> 1592327563 AAA
1592327668 AAA
1592327740 AAA
1592327795 AAA
1592327871 AAA
1592327933 AAA
1592327979 AAA
1592328030 AAA
1071000960
debug3 XCAP rec. from Auth Dispat 00.90.27.75.dc.a2
debug1 XCAP new control block
debug3 Memory : allocate space for ccb : 4abbdf0
debug3 aaaHdlUtilBufInNormalList, free Id 108784624, typ 8
debug1 Send to Authentication dispatcher slice 0 slot 1 port 1
debug1 Message succefully sent
debug1 aaaHdlXcap_start_timer: Timer:0 CCB:4abbdf0
debug1 aaaHdlXcap_start_timer: Time:1071000900 Timeout:
1592833650 AAA
1592833721 AAA
1592833765 AAA
1592833821 AAA
1592833881 AAA
1592833931 AAA
1592833989 AAA
1592876009 AAA
1592963070 AAA
1593028661 AAA
1071000960
debug3 XCAP rec. from Auth Dispat 00.90.27.75.dc.a2
debug1 XCAP existing control block 0x4abbdf0
debug1 XCAP Received AAA_HDL_XCAP_DATA
debug3 aaaHdlUtilBufInNormalList, free Id 108783920, typ 8
debug1 aaaHdlXcap_send_xvss_quest : No Echo
debug1 Send to Authentication dispatcher slice 0 slot 1 port 1
debug1 Message succefully sent
debug1 aaaHdlXcap_start_timer: Timer:0 CCB:4abbdf0
debug1 aaaHdlXcap_clear_timer: Timer:0 CCB:4abbdf0
debug1 aaaHdlXcap_start_timer: Time:1071000900 Timeout:
1593227043 AAA
1593227107 AAA
1593269448 AAA
1593335029 AAA
1593400608 AAA
1593487696 AAA
1593553275 AAA
debug3 XCAP rec. from Auth Dispat 00.90.27.75.dc.a2
debug1 XCAP existing control block 0x4abbdf0
debug1 XCAP Received AAA_HDL_XCAP_DATA
debug1 aaaHdlXcap_clear_timer: Timer:0 CCB:4abbdf0
debug3 aaaHdlUtilBufInNormalList, free Id 108785284, typ 8
debug1 Send AAA_HDL_MGT_USER_REQ
debug11593553350 MeAAAssage succefully
sent debug3 Enter-
ing in aaa_ProcessHdlMsg
1593661847 AAA debug1 AVLAN begin Evt : Req,St : IDLE, name : Avlan ses
0x8000a 00.00.00.00.00.00
1593771485 AAA
1593858571 AAA
1593945613 AAA
1593989703 AAA
debug3 aaaAvlanUserReq ses rec 0x4abbdf0, Avlan ses 0x8000a
debug1 Ctx admin removed from No link, set in MAC link
debug3 aaaAvlanFormatSendAuthReq
debug1 Send Auth. Req. to AAA name : admin, Avlan ses 8000a
1594076811 1594076926AAA
AA Adebug1
AVLAN edebug1nd St : WAIT R ESP, name
: admin, begin Authent Evt : Ret = OKReq, St : IDLE, name : admin, Rec ses :
8000a/ (TRUNCATED)
1594275680 AAA
1594318659 AAA
1594384252 AAA
1594449847 AAA
0x2b002d
debug3 Entering in aaaAuthentReq
debug3 Entering in aaa_ProcessAuthent
debug3 Entering in aaa_FormatSendAuthReq
debug1 Send Auth/Log to RADIUS for admin, Refser:0x2 AAA ses
1594559537 AAA
debug11594559641 AAAAAA_Serv>> Ctx admi n removed from No
link, set in Chal_debug3Rsp link[RAD1594668089] radMain : message received
AAAfrom AAA 1594debug1732585 End AuAAAthent Evt St : WA IT RESP1, name :
admin, ses : 8000a/info 6, Ret = OK [RAD] Message Authentication Request -
msgID = 140026 - received from(TRUNCATED)
1594951952 AAA
1595017406 AAA
1595081951 AAA
1595147511 AAA
0x8502fdfc
info [RAD] radBuildServeurAuth : id = 9
info [RAD] radAddAttr : adding attribute type 1
info [RAD] radAddAttr : adding attribute type 2
info [RAD] radBuildServeurAuth : RADIUS client address =
1595256057 AAA
1595321634 AAA
info [RAD] radAddAttr : adding attribute type 4
info [RAD] radAddAttr : adding attribute type 5
page 18-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Authenticated VLANs
Troubleshooting Using Debug Systrace
1595408715 AAA
1595473430 AAA
try=1
info [RAD] rad_buildauth: port 1 added to access-request
info [RAD] radDoSend OK : id=9, addr=0x8502fd01 port=1645
1595582865 AAA
try=1
1595670050 AAA
info [RAD] radDoSend OK : id=9, addr=0x8502fd01 port=1645
debug3 [RAD] radProcPkt: Got a reply from Radius server , id =
9, code 2, length 59
1595778543 AAA
1595865571 AAA
rcvd.
info [RAD] radProcPkt: Attribute type 25, length 27
info [RAD] radProcPkt: classe (_SBR-CL DN="ADMIN" AT="0"_)
1595953731 AAA
1596040797 AAA
length 6
info [RAD] radProcPkt: Attribute type 26, length 12
info [RAD] radProcPkt: Xylan-specific attribute type 1,
1596127892 AAA
protobind=0
1596213884 AAA
(admin)
info [RAD] radAddAuthGroup :numOfVlans=1, groupeNbr=103,
info [RAD] radProcPkt: RADIUS authentication succeeded
info [RAD] radSendMsgToAaa : message Authentication Reply -
1596300968 AAA
msgID = 140046(TRUNCATED)
1596435553 AAA
1596500948 AAA
debug3 in aaa_DispatchClientRsp,msgId=0x140046
debug1 begin Authent Evt : Auth Reply Ok, St : WAIT RESP1,
name : admin, Rec(TRUNCATED)
1596609497 AAA
1596675141 AAA
1596718079 AAA
AAAAAA
debug3 Entering in aaa_AuthRspOK
debug3 Entering in aaa_ReplyHdlMgt
debug1 Send auth Success, session 8000a15967836691596783761
debug3deb ug1Entering in aaa_ userReturnST_IDLEAVLAN begin Evt :
Aut1596892230h Reply Ok ,St : WAIT RESP, naAAAme : admin Avlan se(TRUNCATED)
1596979322debug1 AAAA AA_Serv>> Ctx adm in removed from Chadebug3l_Rsp
link,se t in No linkEntering in aaaAvlanAuthRs1597109393pOKAAA15 97130885
debug1A AAEnd Authent Evt S t : IDLE, name : , ses :
OKAAA_Serv>> entering in aaaAvlanSendOneCtxToSecondaryCmm
0/ 0, debug3Ret =
1597306117 AAA
1597393189 AAA
1597458749 AAA
Avlan ses 0x8000a
debug2 SL 0xa0070 00.90.27.75.dc.a2, VL 103, proto 1 p 1
debug3 Entering in aaaAvlanReplyHdlMgt
debug1 Send Authent. Success, name : admin, hdl ses 0x4abbdf0x
1597567346 AAA 1597567404 debugAAA2
x516bec0 00.90.27.7XCAP received a mess5.dc.a2age from AAA1597698585159771994
6AAA AAA debu g3debug1 Entering AAA_HDL_MGT_USER_RSPin aaaAvlanFormatSen
Ask stat usdebug3er admin ref 0
/ AAA_HDL_MGT_CHAL_dAcctREQ received 11597850146597850090 AAAAAA
debugdebug13 Send login aaaHdlUtilBufInNormaAcct Evt to AAA admilList, free Id
10863n, 1030344, typ 611598004946598004880 AAAAAA
end SSend to Authenticat it : CONNECTED, name on dispatcher slice : admin, Ret =
OK0 slot 1 port 115981779431598199405 AAAA AA debug2 debReceiv. stat user
adug1min ref 0x8000a 00.90.27.75.dc.a2Message succefully sent
debugdebug11 AVLAN
1598330577 AAA
1598418719 AAA
1598461700 AAA
1598526202 AAA
1600175529 AAA
not found
debug1 Send to Authentication dispatcher slice 0 slot 1 port 1
debug1 Message succefully sent
debug1 aaaHdlXcap_free_ccb: Free ccb 4abbdf0
debug3 Memory : free space for CCB : 4abbdf0
debug2 aaaReleaseIpRecRequest, Mac address 00.90.27.75.dc.a2
AVClient logout:
-> 1628234237 AAA
1628234342 AAA
1628234407 AAA
1628234459 AAA
vlans
debug3 XCAP rec. from Auth Dispat 00.90.27.75.dc.a2
debug1 XCAP new control block
debug3 Memory : allocate space for ccb : 4ad5b10
debug1 Removing MAC = 00902775dca2 from all Authenticated
OmniSwitch Troubleshooting Guide September 2005
page 18-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting Authenticated VLANs
1628234512 AAA
debug3 aaaHdlUtilBufInNormalList, free Id 108802664, typ 8
debug1 Send AAA_HDL_MGT_LOGOUT_REQ
debug1 Message succefully sent
debug3 Entering in aaa_ProcessHdlMsg
debug3 Entering in aaaAvlanReplyHdlFailNoCtx
debug1 Send authent. Failure session 4ad5b10
1628234571 AAA
1628234637 AAA
1628234753 AAA
1628234810 AAA
1628298934 AAA
16283656031628365646 AAAAAA
debug1deb ug3AVLAN begin Evt : Logout
Usr,St : CXCAP received a messONNECTED, name : admage from AAAin Avlan ses
0(TRUNCATED)16
285397161628561215 AAAAAA
debugdebug31 Entering inAAA_HDL_MGT_LOGOUT_R
aaaAvlanLogHdlPerf1SP received
16286701628670943900 AAAAA A
debug3 debuaaaHdlUtilBufInNormag2lList, free
Id 108 636724, typ 6SL 0xa0071 00.90.27.75.dc1628802043.a2, VL 10 3, proto 1 p 1
AAA 1628867630 debuAAAg1 Send to Audebug3thentication d ispatcher slice 0
sAAA_Serv>> entering lot 1 port 1in aaaAvlanSendOneCtxToSeco1628997693ndaryCmm
AAA1629040683 Adebug1AA Message succefully sent debug21629107320 Ask
AAAstat user admin r ef 0x516bec0 00.9 0.27.75.dc.a2debug1
aaaHdlXcap_free_ccb: Free ccb 4ad5b101629193696 16292384AAA76
AAAdebug1
Ctx admin removed from MAC link, setdebug3 in Account. l inkMemory : free space
for CCB : 4ad5b
162936855310AAA
1629456745 AAA
1629543807 AAA
1629630849 AAA
1629696433 AAA
1629783513 AAA
1629827577 AAA
debug1 AVLAN end St : CONNECTED, name : admin, Ret = OK
debug2 Rec Fr SL Del 00.90.27.75.dc.a2, VL 103, p 1, prot = 0
debug2 Receiv. stat user admin ref 0x8000a 00.90.27.75.dc.a2
debug3 Entering in aaaAvlanFormatSendAcct
debug1 Send logout Acct Evt to AAA admin, 103
debug3 in aaaAvlanReturnST_IDLE
debug1 Ctx admin removed from Account. link, set in No link
Dshell Troubleshooting
A set of AVLAN Dshell commands is available under adHelp. Following are the Dshell commands under
adHelp for 6600/6800. For 7700/8800 adHelp is available under nidbg.
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
B05PC1-OS601> dshell
Working: [Kernel]->adHelp
Authentication Dispatcher (AD) Debugging Help
- adDebugResetCounter
- adDebugSetDump = X
: Clear debug counters
: X=1: Enable additional dump hexa in INFO's trace
X=0: Disable additional dump hexa in INFO's trace
- adDebugSetFilterFrame 0xXXXX: Set frame type filter
Available only for INFO's trace
XXXX = Bit field
XXXX = FFFF = No filter
Bit 1: ARP
Bit 2: DHCP
Bit 3: TELNET Bit 4: HTTP
Bit 5: DNS
Bit 6: XCAP
Bit 7: 802.1x Bit 8: Spoofing
page 18-12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Authenticated VLANs
Dshell Troubleshooting
Bit 9: Configuration
- adDebugSetFilterLevel 0xX : Set trace level filter
X = Bit field
Bit 1: ERROR
Bit 2: WARNING
Bit 3: INFO
- adDebugSetFilterPort X
: Set user port number filter
Available only for INFO's trace
X = 0 = No filter
- adDebugShowAvlanIp
- adDebugShowContext
- adDebugShowCounter
- adDebugShowPort
: Display Authentication IP addresses configured
: Display AD's context
: Display debug counters
: Display 802.1x port configured
value = 1424 = 0x590
Working: [Kernel]->
Working: [Kernel]->
Working: [Kernel]->
Working: [Kernel]->
Working: [Kernel]->adDebugSetFilterLevel 0xff
value = 255 = 0xff
Working: [Kernel]->
Working: [Kernel]->adDebugSetFilterFrame 0xffff
value = 65535 = 0xffff
Working: [Kernel]->
AD INFO-> ARP request rcv.on glb.port=0x0,user port=1:Slot=1,Auth.IP
addr.=0x1,Src.MAC known=0x0,Cond.codes=0x16080,Frame=0x63dead8
AD INFO-> TELNET pkt.rcv.from qDispatcher: Slot=1,Glb.port=0x0,User
port=1,Msg.=0x6b01e98,Cond.codes=0x10080,Frame=0x63dead8
Notes.
1. The above is not a complete capture of the successful authentication process. A capture of the entire
process would be several pages.
2. It is recommended that you run this command only in a test environment and with a specific flat set,
rather than all “ffff” shown in the above example.
The Authenticated VLAN adDebugShowContext Function
The adDebugShowContext function displays the following output:
Working: [Kernel]->adDebugShowContext
AD show context
NI Slot
NI Slice
= 1
= 0
Configuration socket identifier = 286
Packet socket identifier = 287
Authenticated IP addr.configured = Yes
DNS name + 'avlBootpmode' config. = Yes
802.1x node parameters configured = Yes
Default Traffic before authent
Port bounding configured
avlBootpMode IP address
= No
= No
= 172.16.106.5
OmniSwitch Troubleshooting Guide September 2005
page 18-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting Authenticated VLANs
Authenticated MAC address
= 00.20.DA.00.00.02
XCAP 802.3 SNAP header
Authenticated DNS name
802.1x EAPol SNAP header
802.1x Authentication control
802.1x Authentication share
802.1x PAE group MAC address
802.1x node MAC address
Debug level
= AA.AA.03.00.20DA.0202
= authent.com
= AA.AA.03.00.0000.888E
= Disable (2)
= Unic (2)
= 01.80.C2.00.00.03
= 00.D0.95.89.9C.D1
= 0x0
Debug frame type filtered
Debug user port filtered
Debug dump
= 0xffffffff
= 0
= No (0)
value = 1031 = 0x407
Run the adDebugShowCounter command to see any possible errors.
Working: [Kernel]->adDebugShowCounter
AD show debug counters
Mem: 'calloc' failed
IPC: Number of message sending retries = 0
IPC: 'zcSendto' failed = 0
IPC: Unexpected msg.identifier to send = 0
= 0
IPC: 'zcSelect' failed
= 0
= 0
= 0
= 0
= 0
= 0
IPC: 'zcRecvFrom' failed
IPC: Unexpected remote application
IPC: Buffer reception failed
IPC: 'zcSocket' failed
IPC: 'zcBind' failed
IPC: Buffer too small for msg. sending = 0
IPC: 'zcBufCreate' failed
IPC: 'zcBufDelete' failed
= 0
= 0
IPC: Unconsistent msg.and buf.length = 0
AVLAN: Unconsistent IP mask config. = 0
AVLAN: Unexpected message identifier rcv.= 0
AVLAN: DNS request rcv.but DNS not conf. = 0
AVLAN: AvlBootpIp address not config.
= 0
8021X: Unexpected message identifier rcv.= 0
8021X: Unexpected node configuration
8021X: Unexpected port configuration
= 0
= 0
8021X: Erroneous destination MAC address = 0
8021X: Maximum port configured reached = 0
Qdrv: 'qDriverCreateStaticQ' failed
Qdrv: 'qDriverGetDefaultQ' failed
= 0
= 0
Qdrv: 'qDriverGetFreeHWBuffer' failed = 0
Qdrv: 'qDriverReleaseHWBuffer' failed = 0
Qdrv: 'qDriverGetDefaultQ' failed
Qdrv: 'qEnqueue' failed
Qdrv: 'qEnqueue' (flood) failed
Qdrv: Dato to send too big
= 0
= 0
= 0
= 0
Qdsp: Unexpected message identifier rcv.= 0
Qdsp: Unexpected frame type received = 0
DNS: Unconsistent DNS header received = 0
DNS: Unconsistent DNS name format rcv. = 0
DNS: DNS request rcv.but no Auth.IP
= 0
= 0
IP:
IP:
IP:
Reverse spoofing failed
IP/TCP/UDP header checksum failed = 0
Unexpected IP header received = 0
page 18-14
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Authenticated VLANs
Dshell Troubleshooting
XCAP: Unexpected message identifier rcv.= 0
value = 1866 = 0x74a
To verify the Authentication IP bound to each VLAN with subnet mask please run the adDebugShowAv-
lanIp command.
Working: [Kernel]->adDebugShowAvlanIp
AD show AVLAN IP addresses
VLAN number
IP address
Mask
= 1
= 10.0.0.92
= 255.255.0.0
Authentication IP address = 10.0.0.253
VLAN number
IP address
Mask
= 13
= 10.4.2.18
= 255.255.0.0
Authentication IP address = 10.4.0.253
OmniSwitch Troubleshooting Guide September 2005
page 18-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting Authenticated VLANs
page 18-16
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
19 Troubleshooting 802.1X
The 802.1X standard defines port-based network access controls, and provides the structure for authenti-
cating physical devices attached to a LAN. It uses the Extensible Authentication Protocol (EAP).
Note. See the “Configuring 802.1X” chapter in the appropriate OmniSwitch Network Configuration Guide
for a detailed explanation about different 802.1X components.
Understanding and troubleshooting of Radius Server in conjunction with switch level troubleshooting is
very helpful.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page 19-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting with the CLI
Troubleshooting 802.1X
Troubleshooting with the CLI
1 Make sure the Radius and Accounting ports are configured the same on both switch and Radius Server.
The default on the Radius Server can be either 1645/1812 for Radius and 1646/1813 for the Accounting.
Layer-2: show aaa server
Server name = rad1
Server type
= RADIUS,
= 133.2.253.1,
= 3,
IP Address 1
Retry number
Time out (sec)
= 2,
Authentication port = 1645,
Accounting port = 1646
2 Verify the port is configured for 802.1x authentication.
Layer-2: show vlan port mobile
cfg
ignore
port mobile def authent enabled restore bpdu
-------+--------+----+--------+---------+---------+-------
2/1
2/2
2/3
2/4
on
on
on
on
1 on-avlan
1 on-avlan
1 on-8021x
1 on-8021x
on
on
on
on
on
on
on
on
on
on
on
on
3 Check the physical status and VLAN assignment of the port.
Layer-2: show vlan port 2/3
vlan
type
status
--------+---------+--------------
1
101
default forwarding
mobile forwarding
4 Check the status of the MAC address table on the 802.1x port.
Layer-2: show mac-address-table 2/3
Legend: Mac Address: * = address not valid
Vlan
------+-------------------+--------------+-----------+------------+-----------
101 00:0f:1f:d5:54:95 learned 10800 bridging 2/3
Total number of Valid MAC addresses above = 1
Mac Address
Type
Protocol
Operation
Interface
5 If a user can not move to VLAN-X after authentication, it could mean that authentication is disabled on
that VLAN, or that the Radius server didn't return a specific VLAN number in the return list attribute.
Please verify that the server is configured properly with the correct return list attribute type as explained in
the user guide. To move a user into a specific VLAN, Radius server has to return the attribute "Alcatel-
Auth-Group" with a valid Authenticated VLAN number.
Layer-2: show vlan 101
Name
: bungaku,
Administrative State: enabled,
Operational State : enabled,
Spanning Tree State : disabled,
page 19-2
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1X
Troubleshooting with the CLI
Authentication
IP Router Port
IPX Router Port
: enabled,
: none,
: none,
6 Verify the status of the 802.1x port using the show 802.1x command. Read the OmniSwitch CLI Refer-
ence Guide to understand the explanation for each field.
Layer-2: show 802.1x 2/3
802.1x slot/port = 2/3
authenticator PAE state
= AUTHENTICATED,
backend authenticator state = IDLE,
direction
operational directions
port-control
= both,
= both,
= auto,
= Authorized,
= 60,
= 30,
= 30,
= 30,
= 2,
port status
quiet-period (seconds)
tx-period (seconds)
supp-timeout (seconds)
server-timeout (seconds)
max-req
re-authperiod (seconds)
reauthentication
= 3600,
= no
7 Check for the 802.1x port statistics. Read the OmniSwitch CLI Reference Guide to understand the
detail of each field.
Layer-2: show 802.1x statistic 2/3
802.1x slot/port = 2/3
EAPOL frames received
EAPOL frames transmitted
= 28,
= 38,
= 8,
EAPOL start frames received
EAPOL logoff frames received
EAP Resp/Id frames received
EAP Response frames received
EAP Req/Id frames transmitted
EAP Req frames transmitted
Invalid EAPOL frames received
= 0,
= 10,
= 10,
= 13,
= 10,
= 0,
EAP length error frames received = 0,
Last EAPOL frame version
Last EAPOL frame source
= 1,
= 00:0f:1f:d5:54:95
OmniSwitch Troubleshooting Guide September 2005
page 19-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Using Debug CLI
Troubleshooting 802.1X
Troubleshooting Using Debug CLI
Assuming Radius communication takes place on UDP port 1645:
Layer-2: debug ip packet protocol udp port 1645 start
C S 1/1 00d09579640e->00d0956af558 IP 10.1.1.1->133.2.253.1 UDP 1025,1645
C R 1/1 00d0956af558->00d09579640e IP 133.2.253.1->10.1.1.1 UDP 1645,1025
C S 1/1 00d09579640e->00d0956af558 IP 10.1.1.1->133.2.253.1 UDP 1025,1645
C R 1/1 00d0956af558->00d09579640e IP 133.2.253.1->10.1.1.1 UDP 1645,1025
1 R CMM (00d09579640e)->(00d0956af558) IP 10.1.1.1->133.2.253.1 UDP 1025,1645
1 S 1/1 00d09579640e->00d0956af558 IP 10.1.1.1->133.2.253.1 UDP 1025,1645
1 R 1/1 00d0956af558->00d09579640e IP 133.2.253.1->10.1.1.1 UDP 1645,1025
1 S CMM 00d0956af558->00d09579640e IP 133.2.253.1->10.1.1.1 UDP 1645,1025
1 R CMM (00d09579640e)->(00d0956af558) IP 10.1.1.1->133.2.253.1 UDP 1025,1645
1 S 1/1 00d09579640e->00d0956af558 IP 10.1.1.1->133.2.253.1 UDP 1025,1645
1 R 1/1 00d0956af558->00d09579640e IP 133.2.253.1->10.1.1.1 UDP 1645,1025
1 S CMM 00d0956af558->00d09579640e IP 133.2.253.1->10.1.1.1 UDP 1645,1025
2 R 2/3 000f1fd55495->(ffffffffffff) ARP Request 133.2.222.152->133.2.222.152
2 R 2/3 000f1fd55495->(ffffffffffff) ARP Request 133.2.222.152->133.2.222.152
2 R 2/3 000f1fd55495->(ffffffffffff) ARP Request 133.2.222.152->133.2.222.152
Layer-2: debug systrace appid aaa level debug3
Layer-2: debug systrace enable
Layer-2: debug systrace show log
To verify what the Radius server has returned, please look at the following line in bold:
radAddAuthGroup :numOfVlans=1, groupeNbr=101, protobind=0
For example:
431612866 AAA
431612997 AAA
431613178 AAA
debug3 entering in aaaProcessPortManager
debug3 rec from PM 34, status ad UP, op DOWN
debug2 [ONEX] onex_process_pm LINK_STATUS 2003
432450759 TRAP warnin ping NMS 10.2.0.250 : no echo
433243756 AAA
433243886 AAA
433244071 AAA
433244189 AAA
433244328 AAA
440336239 AAA
0:f:1f:d5:54:95
440336371 AAA
440336460 AAA
eap msg len 7
440336740 AAA
debug3 entering in aaaProcessPortManager
debug3 rec from PM 34, status ad UP, op UP
debug2 [ONEX] onex_process_pm LINK_STATUS 2003
debug2 [ONEX] onex_auth_txCannedFail sent to 2003
debug2 [ONEX] onex_auth_txReqId sent to 2003
debug2 [ONEX] onex_auth_disp_proc_eapol received from 34
debug2 [ONEX] onex_auth_disp_proc eap resp/ID
info [ONEX] onex_bauthsm_sendRespToServer user name len 7,
debug1 begin Authent Evt : Req, St : IDLE, name : user101, Rec
ses : 48c4288(TRUNCATED)
440336834 AAA
440336915 AAA
440337002 AAA
440356146 AAA
0xf0011
debug3 Entering in aaaAuthentReq
debug3 Entering in aaa_ProcessAuthent
debug3 Entering in aaa_FormatSendAuthReq
debug1 Send Auth/Log to RADIUS for user101, Refser:0x2 AAA ses
440435825 440435891AA AAAA
fr[RAD] radMain : messom No link, set in Cage received from AAhal_Rsp linkA
440440595058594997 AAAAAA infodebug 1 [RAD] Message AEnd Authent Evt
debug1d ebug3AAA_Serv>> Ctx user101 removed
St :uthentication Reques WAIT RESP1, name : t - msgID = 140026 -user101, ses :
48c42 received from(TRUNC88/ c, Ret = OKATED)
page 19-4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1X
Troubleshooting Using Debug CLI
440814250 AAA
440874069 AAA
440933046 AAA
0xa010101
info [RAD] radBuildServeurAuth : id = 19
info [RAD] radAddAttr : adding attribute type 1
info [RAD] radBuildServeurAuth : RADIUS client address =
441012638 AAA
441091272 AAA
441152216 AAA
441230837 AAA
441311563 AAA
441391033 AAA
441451000 AAA
access-request
441550316 AAA
441610744 AAA
try=1
info [RAD] radAddAttr : adding attribute type 4
info [RAD] radAddAttr : adding attribute type 5
info [RAD] rad_buildauth: port 35 added to access-request
info [RAD] radAddAttr : adding attribute type 79
info [RAD] rad_buildauth: EAP msg added to access-request
info [RAD] radAddAttr : adding attribute type 80
info [RAD] rad_buildauth: PW_MESSAGE_AUTHENTICATOR added to
info [RAD] radBuildReq : Updated MESSAGE_AUTHENTICATOR
info [RAD] radDoSend OK : id=19, addr=0x8502fd01 port=1645
441709499 AAA
try=1
441789195 AAA
info [RAD] radDoSend OK : id=19, addr=0x8502fd01 port=1645
debug3 [RAD] radProcPkt: Got a reply from Radius server , id =
19, code 11, length 77
441889383 AAA
441968957 AAA
442048564 AAA
442107543 AAA
442167497 AAA
442247130 AAA
442326726 AAA
info [RAD] radProcPkt: RADIUS challenge for user (user101)
info [RAD] radProcPkt: Attribute type 24, length 15
info [RAD] radProcPkt: state rcvd.
info [RAD] radProcPkt: Attribute type 79, length 24
info [RAD] radProcPkt: Attribute type 80, length 18
info [RAD] radProcPkt: RADIUS challenge for user (user101)
info [RAD] radSendMsgToAaa : message Challenge Request -
msgID = 140048 - (TRUNCATED)
442426339 AAA
442485995 AAA
debug3 in aaa_DispatchClientRsp,msgId=0x140048
debug1 begin Authent Evt : Chal Req, St : WAIT RESP1, name :
user101, Rec se(TRUNCATED)
442605885 AAA
442645390 AAA
442705166 AAA
48c4288
debug3 Entering in aaa_AuthChalReq
debug3 Entering in aaa_ReplyAuthChalReq
debug1 Send Challenge Question, name : user101, session
442784858 442784996AAA
AAA
debug1 deAAA_Serv>> Ctx user1bug201 removed
from Chal_Rsp link, set [ONEX] onex_bauthsm_in Client_Rsp linktx
Req sent to 2003 4 42944015442944172 AAAAAA
debug1debug2 End Authent
[ONEX] onex_auth_disEvt St : WAIT CHAL, p_proc_eapol receivename : user101, ses
d from 34/ 0:f:1f:d5: 48c4288/ c, Ret :54:95= OK
443142527 AAA
443202791 AAA
debug2 [ONEX] onex_auth_disp_proc eap resp!=id
debug1 begin Authent Evt : Chal Resp, St : WAIT CHAL, name :
user101, Rec se(TRUNCATED)
443322375 AAA
443361687 AAA
443420706 AAA
debug3 Entering in aaa_UserChalRsp
debug3 Entering in aaa_FormatSendChalRsp
debug1 AAA_Serv>> Send Challenge Response to RADIUS client,
name user101, Re(TRUNCATED)
443540837 AAA
debug1 443540929AAA_ Serv>> Ctx user101 AAAremoved from
Client_Rsp link, set in Chal_Rsp linkdebug3 443660523[RAD] radMain : message
AAAreceived from AAA
nameAAA : user101, ses :
debug144372043 4End Authent Evt St : WAIT RESP2,
48c4288/ c, Re t = OKinfo [RAD] Message Chal-
lenge Reply - msgID = 14002a - received from AAA f(TRUNCATED)
443899513 AAA
443959256 AAA
444039009 AAA
0xa010101
info [RAD] radBuildServeurAuth : id = 20
info [RAD] radAddAttr : adding attribute type 1
info [RAD] radBuildServeurAuth : RADIUS client address =
444117495 AAA
444177453 AAA
SBR-CH 439|1
444276734 AAA
info [RAD] radAddAttr : adding attribute type 4
info [RAD] radBuildServeurAuth : RADIUS client specData =
info [RAD] radAddAttr : adding attribute type 24
OmniSwitch Troubleshooting Guide September 2005
page 19-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Using Debug CLI
Troubleshooting 802.1X
444336676 AAA
444417261 AAA
444496871 AAA
444556834 AAA
444636441 AAA
444716065 AAA
access-request
444795713 AAA
444875605 AAA
try=1
info [RAD] radAddAttr : adding attribute type 5
info [RAD] rad_buildauth: port 13 added to access-request
info [RAD] radAddAttr : adding attribute type 79
info [RAD] rad_buildauth: EAP msg added to access-request
info [RAD] radAddAttr : adding attribute type 80
info [RAD] rad_buildauth: PW_MESSAGE_AUTHENTICATOR added to
info [RAD] radBuildReq : Updated MESSAGE_AUTHENTICATOR
info [RAD] radDoSend OK : id=20, addr=0x8502fd01 port=1645
444954886 AAA
try=1
info [RAD] radDoSend OK : id=20, addr=0x8502fd01 port=1645
445054248 AAA
debug3 [RAD] radProcPkt: Got a reply from Radius server , id =
20, code 2, length 113
445154438 AAA
445214356 AAA
info [RAD] radProcPkt: Attribute type 25, length 57
info [RAD] radProcPkt: classe
(_SBR2CLƆ›žÍÛ¨Õ÷À_€$_€_˜€_€_ªÔèÕ'Äà±_€_Æ(TRUNCATED)
445333272 AAA
445393232 AAA
445473011 AAA
length 6
info [RAD] radProcPkt: Attribute type 79, length 6
info [RAD] radProcPkt: Attribute type 26, length 12
info [RAD] radProcPkt: Xylan-specific attribute type 1,
445552466 AAA info [RAD] radAddAuthGroup :numOfVlans=1, groupeNbr=101, proto-
bind=0
445650740 AAA
445710761 AAA
445790313 AAA
info [RAD] radProcPkt: Attribute type 80, length 18
info [RAD] radProcPkt: RADIUS authentication succeeded ()
info [RAD] radSendMsgToAaa : message Authentication Reply -
msgID = 140046(TRUNCATED)
445889783 AAA
445969235 AAA
debug3 in aaa_DispatchClientRsp,msgId=0x140046
debug1 begin Authent Evt : Auth Reply Ok, St : WAIT RESP2,
name : user101, R(TRUNCATED)
446069472 AAA
446128451 AAA
446168732 AAA
446228701 AAA
446287686 AAA
446347653 AAA
debug3 Entering in aaa_AuthRspOK
debug3 8021X Authentication
debug3 Entering in aaa_ReplyHdlMgt
debug1 Send auth Success, session 48c4288
debug3 446287793Ente ring in aaa_userRetAAAurnST_IDLE
debug2 AAA[ ONEX] onex_proces s_aaa_rsp eap messadebug1ge
@ 48c42a0 l en: 4AAA_Serv>> Ctx user101 removed fr om Chal_Rsp link,
s446467496et in No li nkAAA 44652658info0 AAA[ONEX] o nex_process_aaa_r
sp auth success ifidebug1ndex 2003 En d Authent Evt St : 446606251IDLE, name :
, ses :
to 2003
446746845 AAA
flush 0
447276940 AAA
flush 0
447355590 AAA
flush 0
0/ 0AAA, Ret = OK
debug2 [ONEX] onex_auth_txCannedSuccess sent
debug2 SL 0xa0070 00.0f.1f.d5.54.95, VL 101, proto 1 p 2003,
debug2 SL 0xa0070 00.0f.1f.d5.54.95, VL 101, proto 1 p 2003,
debug2 SL 0xa0070 00.0f.1f.d5.54.95, VL 101, proto 1 p 2003,
page 19-6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1X
Dshell Troubleshooting
Dshell Troubleshooting
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
Launch the NiDebugger. Go to the NI where user is connected.
2:0 nidbg> adHelp
2:0
2:0
2:0 Authentication Dispatcher (AD) debugging help
2:0
2:0 - adDebugResetCounter
: Clear debug counters
2:0 - adDebugSetDump = X
: X=1: Enable additional dump hexa in INFO's
trace
2:0
X=0: Disable additional dump hexa in INFO's
trace
2:0 - adDebugSetFilterFrame 0xXXXX: Set frame type filter
2:0
2:0
2:0
2:0
2:0
2:0
2:0
2:0
Available only for INFO's trace
XXXX = Bit field
XXXX = FFFF = No filter
Bit 1: ARP
Bit 2: DHCP
Bit 3: TELNET Bit 4: HTTP
Bit 5: DNS
Bit 6: XCAP
Bit 7: 802.1x Bit 8: Spoofing
Bit 9: Configuration
2:0 - adDebugSetFilterLevel 0xX : Set trace level filter
2:0
2:0
2:0
X = Bit field
Bit 1: ERROR
Bit 3: INFO
Bit 2: WARNING
2:0 - adDebugSetFilterPort X
2:0
2:0
: Set user port number filter
Available only for INFO's trace
X = 0 = No filter
2:0 - adDebugShowAvlanIp
ured
: Display Authentication IP addresses config-
2:0 - adDebugShowContext
2:0 - adDebugShowCounter
2:0 - adDebugShowPort
2:0 value = 0 = 0x0
: Display AD's context
: Display debug counters
: Display 802.1x port configured
Check the port status using the following command:
2:0 nidbg> adDebugShowPort
2:0
2:0
2:0 AD show port configuration
2:0
2:0
2:0
2:0
2:0
2:0
2:0
2:0
User port
State
Direction
= 3
= authorized_serv_data (4)
= In-Out (0)
Source MAC addr. = 00.0F.1F.D5.54.95
User port
State
= 4
= unauthorized (3)
OmniSwitch Troubleshooting Guide September 2005
page 19-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting 802.1X
2:0
2:0
Direction
Source MAC addr. = 00.00.00.00.00.00
= In-Out (0)
2:0 value = 0 = 0x0
To verify the sequence of the packet flow, set the below Dshell flags to troubleshoot the issue. The best
way to troubleshoot is to compare the failed case with good case.
2:0 nidbg> adDebugSetFilterFrame 0xffff
2:0 nidbg> adDebugSetFilterLevel 0xff
2:0 AD INFO-> 802.1x port config.rcv.: Msg.=0x4370000
2:0
2:0 AD INFO-> 802.1x port config.rcv.:
2:0
2:0
Slot=2,Msg.=0x4370000
2:0 AD INFO-> 802.1x's port broadcast egress traffic blocked:
2:0 Slot=2,Glb.port=0x22,User port=3
2:0 slnFlushPortVlanHandler(1623): count = 1
2:0 qDriverSendReadyToEsmDriver: zcSendto succeeded port 0x22
2:0
2:0 AD INFO-> EAPol pkt.rcv.from AAA's 802.1x:
2:0
2:0
Slot=2,Msg.=0x44ff800
2:0 AD INFO-> EAPol pkt.sent out:
2:0
2:0
Slot=2,Glb.port=0x22,User port=3,Frame=0x44fa000
2:0 AD INFO-> EAPol pkt.rcv.from AAA's 802.1x:
2:0
2:0
Slot=2,Msg.=0x4509800
2:0 AD INFO-> EAPol pkt.sent out:
2:0
2:0
Slot=2,Glb.port=0x22,User port=3,Frame=0x4506800
2:0 AD INFO-> No EAPol pkt., rcv.on 802.1x glb.port=0x22,user port=3: discarded:
2:0
2:0
2:0
Slot=2,802.1x port's state=3,Auth.Ctrl=1,Auth.Share=2,
Src.MAC addr.=00.0F.1F.D5.54.95,Cond.codes=0x4180,Frame=0x4662800
2:0 AD INFO-> No EAPol pkt., rcv.on 802.1x glb.port=0x22,user port=3: discarded:
2:0
2:0
2:0
Slot=2,802.1x port's state=3,Auth.Ctrl=1,Auth.Share=2,
Src.MAC addr.=00.0F.1F.D5.54.95,Cond.codes=0x4180,Frame=0x436f000
2:0 AD INFO-> EAPol pkt., rcv.on 802.1x glb.port=0x22,user port=3: sent to
802.1x CMM:
2:0
2:0
2:0
Slot=2,802.1x port's state=3,Auth.Ctrl=1,Auth.Share=2,
Src.MAC addr.=00.0F.1F.D5.54.95,Cond.codes=0x8080,Frame=0x4474800
2:0 AD INFO-> EAPol pkt.sent to AAA's 802.1x:
2:0
2:0
Slot=2,Glb.port=0x22,User port=3,Msg.=0x15cfd70
2:0 AD INFO-> 802.1x port config.rcv.: Msg.=0x4478000
2:0
2:0 AD INFO-> 802.1x port config.rcv.:
2:0
2:0
Slot=2,Msg.=0x4478000
2:0 AD INFO-> 802.1x's port broadcast egress traffic blocked:
2:0
2:0
Slot=2,Glb.port=0x22,User port=3
2:0 AD INFO-> EAPol pkt.rcv.from AAA's 802.1x:
2:0 Slot=2,Msg.=0x447d800
page 19-8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 802.1X
Dshell Troubleshooting
2:0
2:0 AD INFO-> EAPol pkt.sent out:
2:0
2:0
Slot=2,Glb.port=0x22,User port=3,Frame=0x4479000
2:0 AD INFO-> EAPol pkt.from supplicant, rcv.on 802.1x glb.port=0x22,user
port=3: sent to 802.1x CMM:
2:0
2:0
2:0
Slot=2,802.1x port's state=6,Auth.Ctrl=1,Auth.Share=2,
Src.MAC addr.=00.0F.1F.D5.54.95,Cond.codes=0x8080,Frame=0x447c800
2:0 AD INFO-> EAPol pkt.sent to AAA's 802.1x:
2:0
2:0
Slot=2,Glb.port=0x22,User port=3,Msg.=0x15cfe90
2:0 AD INFO-> 802.1x port config.rcv.: Msg.=0x4484000
2:0
2:0 AD INFO-> 802.1x port config.rcv.:
2:0
2:0
Slot=2,Msg.=0x4484000
2:0 AD INFO-> 802.1x's port broadcast egress traffic unblocked:
2:0
2:0
Slot=2,Glb.port=0x22,User port=3
2:0 AD INFO-> EAPol pkt.rcv.from AAA's 802.1x:
2:0
2:0
Slot=2,Msg.=0x4481800
2:0 AD INFO-> EAPol pkt.sent out:
2:0
2:0
Slot=2,Glb.port=0x22,User port=3,Frame=0x4488000
2:0 AD INFO-> DHCP pkt.from known src.MAC, rcv.on 802.1x glb.port=0x22,user
port=3: sent to UDP Relay NI:
2:0
2:0
2:0
Slot=2,802.1x port's state=4,Auth.Ctrl=1,Auth.Share=2,
Src.MAC addr.=00.0F.1F.D5.54.95,Cond.codes=0x4100,Frame=0x446c800
2:0 AD INFO-> DHCP pkt.from known src.MAC, rcv.on 802.1x glb.port=0x22,user
port=3: sent to UDP Relay NI:
2:0
2:0
2:0
Slot=2,802.1x port's state=4,Auth.Ctrl=1,Auth.Share=2,
Src.MAC addr.=00.0F.1F.D5.54.95,Cond.codes=0x4100,Frame=0x4483800
2:0 AD INFO-> ARP request, rcv.on 802.1x glb.port=0x22,user port=3:
2:0
2:0
2:0
Slot=2,802.1x port's state=4,Auth.Ctrl=1,Auth.Share=2,
Src.MAC known=0x1,Cond.codes=0x6000,Frame=0x44a4000
2:0 AD INFO-> ARP request, rcv.on 802.1x glb.port=0x22,user port=3:
2:0
2:0
2:0
Slot=2,802.1x port's state=4,Auth.Ctrl=1,Auth.Share=2,
Src.MAC known=0x1,Cond.codes=0x6000,Frame=0x4578000
2:0 AD INFO-> ARP request, rcv.on 802.1x glb.port=0x22,user port=3:
2:0
2:0
Slot=2,802.1x port's state=4,Auth.Ctrl=1,Auth.Share=2,
Src.MAC known=0x1,Cond.codes=0x6000,Frame=0x4678000
A packet capture that is more specific to EAPOL is done by setting bit-7 of the adDebugSetFilterFrame
Dshell command.
OmniSwitch Troubleshooting Guide September 2005
page 19-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Dshell Troubleshooting
Troubleshooting 802.1X
page 19-10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
A OS6600/OS7700/OS8800
Architecture Overview
The switch benefits from an intelligent, multi-layer switching, fully distributed and passive backplane
architectural design that provides redundancy of critical hardware and software elements for a continuous
(non-stop) traffic processing in any network conditions without a single point of failure. Switch process-
ing scheme includes a non-blocking store-and-forward crossbar design switching fabric with a distributed
processing. The architecture supports a true redundancy of management and the switch fabric. The
OmniSwitch 7000 new and highly intelligent design encompasses advanced distributed architecture
including state-of-the-art ASICs.
The architecture is designed around three major ASICs named the Catalina, the Coronado and the
Nantucket.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page -1
Download from Www.Somanuals.com. All Manuals Search And Download.
The MAC ASIC
The MAC ASIC
There are two different types of MAC layer ASICs:
• Catalina
• Firenze
Catalina
The Catalina basically provides three functions: Media Access Control (MAC) Layer functions, data buff-
ering, and statistics accumulation and storage for each port.
The Catalina provides the interface between Ethernet analog devices (10/100 Mbps and 1000 Mbps) and
the Coronado. The Catalina has a total of thirteen network interfaces, twelve of which support 10/100
Mbps Ethernet through a RMII (Reduced Media Independent Interface) and the thirteenth supports 1000
Mbps. All Catalina ASIC buffer memory is dedicated to providing a smooth stream of data inbound from
the Ethernet ports to the Coronado or outbound from the Coronado to the Ethernet ports.
The Catalina does not contain system-level buffering for storing frames for later transmission. The Coro-
nado Queue Manager provides this function. Catalina packet processing is limited to physical-layer
processing. It does not perform any protocol processing or frame recognition. The Coronado handles these
functions. One or two Catalina ASIC is located on any network interface.
F-BUS
Coronado
XY-BUS
Catalina 0
Catalina 1
...
ENI-C-24
OS-7/8XXX
...
12 10/100 ports
12 10/100 ports
page -2
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
The MAC ASIC
F-BUS
Coronado
GNI-U-2
OS-7XXX
XY-BUS
Catalina 0
Catalina 1
1 Gig Port
F-BUS
1 Gig port
F-BUS
Coronado 0
Coronado 3
…
XY-BUS
XY-BUS
Catalina 6
Catalina 7
Catalina 0
Catalina 1
Gigabit port 7
Gigabit port 8
Gigabit port 1
Gigabit port 2
GNI-U/C-8
OmniSwitch Troubleshooting Guide September 2005
page -3
Download from Www.Somanuals.com. All Manuals Search And Download.
The MAC ASIC
Firenze
The Firenze basically provides three functions: Media Access Control (MAC) Layer functions, Data buff-
ering, Flow Control and statistics accumulation and storage for each port.
Firenze handles up to six Ethernet interfaces that can support independently either 10 or 100 or 1000 Mbit/
s throughput using independently either TBI or GMII interfaces.
The Firenze Based GNI is a 1Gbps Ethernet Switching Module for the Falcon system. Two Versions of
the board are configured as below:
• GNI-U12, 12-port fiber Gigabit module equipped with twelve Pluggable SFP Transceivers which can
support short, long and very long haul applications.
• GNI-C12, 12-port copper Gigabit module equipped with twelve RJ45 connector, individually config-
urable as 10/100 or 1000 Base-T.
The Firenze based GNI modules for Eagle OS-8800 are as follows:
• OS8-GNI2-C24, 24-port copper Gigabit module equipped with Twenty four RJ45 connector compati-
ble with cat5 or cat5e minimum cabling specification. Due to the use of Ten-Bit Interface
• TBI between the PHY and Firenze, the ports are limited to 1000BASE-T speed only.
• GNI2-U24, 24-port fiber Gigabit module equipped with Twenty four Pluggable SFP Transceivers.
F-BUS
Coronado
XY-BUS
Firenze 0
Firenze 1
...
...
6 Gigabit ports
6 Gigabit ports
page -4
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
The MAC ASIC
F-BUS
F-BUS
Coronado 3
Coronado 0
…
XY-BUS
XY-BUS
Firenze 6
Firenze 7
Firenze 1
Firenze 0
6 Gigabit ports
6 Gigabit ports
6 Gigabit ports
6 Gigabit ports
GNI-U/C-24
OS-8800
The Coronado ASIC
The Coronado ASIC is the centerpiece of this advanced architectural design. While each ASIC performs a
vital function in the overall architecture, the Coronado provides most of the key features like wire-rate L2
and L3 switching and routing.
Coronado features include:
• Classifier and switching ASIC
• Full wire-speed L2/L3
• Provides connectivity for 24x10/100 Mbps ports or 2x1000 Mbps ports
• Up to 64K L3 Table Entries. 64K L2 Entries.
• Four Priority Levels. 2,048 Virtual Queues.
• Flow based QoS with IEEE 802.1Q/p, IP-TOSp or IP-DiffServ
• Up to 4,096 IEEE 802.1Q VLAN support.
• Link Aggregation.
• Port mirroring/monitoring.
OmniSwitch Troubleshooting Guide September 2005
page -5
Download from Www.Somanuals.com. All Manuals Search And Download.
The MAC ASIC
The Coronado ASIC contains both Ingress and Egress functions. Ethernet frames flow from the Catalina
through the Ingress Coronado, through the Nantucket switch fabric, then through the Coronado Egress
logic and finally out the Egress Catalina.
Note: Frames always flow through the Nantucket, even if the input and output ports are on the same Coro-
nado ASIC. One or more Coronado ASIC are located on the network interface cards. It is a store and
forward technology meaning that the entire PDU must be received before it is transferred across the fabric
to the egress port. Each Coronado provides 2.4Gbps interface to the backplane.
Coronado has a build-in Hardware Routing Engine known as HRE. This HRE provides the function of
Layer 2 switching as well as Layer 3 routing. Coronado also has classifier logic built-in, which enables the
packet to be classified according to the policies defined.
On the Network Interface cards for OmniSwitch 7XXX, there is one Coronado per NI.
Ethernet switching modules (10/100MB) always have one Coronado for both OmniSwitch 7/8XXX.
OmniSwitch 8800 has four Coronado ASICs (0 t0 3) per NI for all the GNI modules
Coronado is referred to as a Slice. Therefore, the Coronado on a network interface card in a working chas-
sis is referred to by slot and slice number.
Functional Description
SSRAM
SDRAM0
SDRAM1
C
a
t
a
l
i
n
a
0
F
B
U
S
_
T
X
X
Y
B
U
S
_
R
X
F
A
B
R
I
Queue
Manager
HRE
BBUS
SPARC
F
B
U
S
_
R
X
C
A
t
a
l
i
n
a
1
X
Y
B
U
S
_
T
X
C
Egress Logic
page -6
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
The MAC ASIC
Coronado: The “Brain” of the System
• Provides hardware performance for most features on the OmniSwitch.
• Involved in both the ingress and egress packet processing.
• Provides a high speed connection to Catalina via the XYBUS. XYBUS is two unidirectional busses
between Catalina and Coronado. XYBUS is 1.24 Gbps.
• Provides 2 high speed connections to the fabric via the FBUS. An FBUS is two unidirectional busses.
• Provides connections to all the ASICs via the management BUS known as BBUS. BBUS is a bidirec-
tional bus used for Management purposes for NI/CMM communications.
Coronado Specifications
• On Chip 170 KB memory (for FIFOs, Queue Manager and ingress buffering)
• Off Chip memory
• SSRAM: 2Mbytes for pseudoCAM entries (128k)
• 64k Layer 2 entries (32K for SA and 32K for DA)
• 64k Layer 3 entries
• SDRAM-0: 32Mbytes (Part of it is allocated to HW for HRE header cache, Priority Description Index
etc; remaining is available to Software)
• SDRAM-1: 16Mbytes used for the buffers
• V7 Sparc Core running at 143 MHz—integrates cache memory:
- 8KB for instruction
- 4KB for data (sending on BBUS)
- 2KB for packet cache (for faster access to the packet being processed)
• Provides software support for distributed features. Executes the Operating System on each NI. The
configuration of the Coronado is updated by the CMM.
• The Coronado ASIC supports 2048 queues and 4096 buffers. Buffers are organized in two lists:
- List 1: 4096-128=3968 buffers of 2048 bytes
- List 2: 128 buffers of 16384 bytes for Jumbo Frames
• Coronado keeps track of the buffer utilization on per port basis. A per port threshold triggers the
802.3x pause frame.
• Each queue can be assigned:
- An egress physical port or can be designated as a multicast queue
- A pay that determines the right to transmit a certain amount of data
- A priority (4 for unicast - 4 for multicast)
- A maximum length, which is the maximum number of packets that can be queued
OmniSwitch Troubleshooting Guide September 2005
page -7
Download from Www.Somanuals.com. All Manuals Search And Download.
Queue Driver Interaction
• Queues are maintained by the software module known as the Queue Driver runs on each NI. It provides
the interaction to other software modules in the Falcon/Eagle product to create/modify/delete/manage
all the queues in the system. This module provides debugging information required for the queues and
maintains the statistics. This module maintains all the information required about all the queues on the
Coronado.
Software Module Interaction
• Coronado ASIC interacts with the following software modules:
• Ethernet Driver
• Queue Dispatcher
• NI Supervision Task
• L2 Source Learning
• L3 Manager/IPMS
• QoS Manager
• Link Aggregation
Queue Driver Interaction
The interactions of each module with Queue Driver is as follows:
Ethernet Driver
Ethernet driver on the CMM is responsible for initializing the Coronado when the system comes up, when
a board is inserted/removed from the slot and when a link goes up or down. On the initial initialization the
Ethernet driver on the CMM should send the slot configuration information for all the slots in the system.
The initial configuration sent by the Ethernet driver has the following information for each of the slots
present in the system:
• Number of default queues per port (this is user configurable. The default value is 4 queues per port.
The CLI command to change this is provided by the Ethernet driver. The value of this parameter can be
either 2 or 4. This value is configurable per slot).
• Port configuration for each of the ports in the slot.
• Based on the port configuration the Queue Driver will assign ports.
Queue Dispatcher
The interaction between the queue driver and the queue dispatcher is mainly for freeing a default queue
associated with a port when the port goes down and to modify the priority of a queue. When the queue
driver gets the link down event for a port a message is sent to the queue dispatcher task. The Queue
dispatcher performs the appropriate steps to free the queue and updates the status of the request by send-
ing a message back to the queue driver. The queue driver maintains statistics about the number of queues
in an error state. When the priority of a queue needs to be changed, a message is sent to the queue
dispatcher.
page -8
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Queue Driver Interaction
NI Supervision
Queue driver sends the task initialization and task ready messages to the NI Supervision task just before
receiving any configuration information from the CMM Ethernet driver. This indicates to the NI supervi-
sion task that the queue driver task is ready.
Source Learning
L2 Destination Address Manager is a software block of Source Learning. It is responsible for destination
MAC address learning and programming the L2 destination address pseudo cam on the Coronado.
L3 Manager/IPMS
The L3 Manager/IPMS Module interacts with the Queue Driver to get the default queue associated with a
physical port associated with the pseudo cam entry.
QoS Manager
The interaction between the QoS Manager and the Queue Driver can be under following conditions:
Destination MAC Learning
When a L2 destination MAC address is learnt, the source-learning module notifies the QoS Manager of
the MAC learnt. QoS Manager checks to see if any QoS Policy is configured for the MAC address. If a
QoS Policy is present and if it requires that a new queue be created for the flow, then the QoS Manager
requests the Queue Driver for a new queue with the appropriate policy requirements for the queue. The
Queue driver will allocate a new queue if a free queue is available. Depending on the policy, the QoS
Manager can request for multiple consecutive queues. In this case, the QoS Manager can request for
number of consecutive default queues and later modify the parameters of the individual queues
L3 Pseudo CAM Learning
When a L3 address is learned, the L3 manager module notifies the QoS Manager of the L3 address learnt.
QoS Manager checks to see if any QoS Policy is configured for the L3 address. If a QoS Policy is present
and if it requires that a new queue be created for the flow, then the QoS Manager requests the Queue
Driver for a new queue with the appropriate policy requirements for the queue. The Queue driver will allo-
cate a new queue if a free queue is available. Depending on the policy, the QoS Manager can request for
multiple consecutive queues. In this case the QoS Manager can request for number of consecutive default
queues and later modify the parameters of the individual queues
QoS Policy Change
When a QoS Policy changes, the QoS Manager is notified. QoS Manager checks to see if any flows exist
for the policy and if a new queue was allocated for it. If so, it requests the Queue Driver to modify certain
parameters of the queue with the appropriate queue parameters. Only certain parameters of a queue can be
modified on the fly.
OmniSwitch Troubleshooting Guide September 2005
page -9
Download from Www.Somanuals.com. All Manuals Search And Download.
Queue Driver Interaction
QoS Policy Deleted
When a QoS Policy is deleted, the QoS Manager is notified. It checks to see if there are any flows associ-
ated with the QoS Policy. The queue id for all the pseudo cam entries associated with the policy should be
reprogrammed with a default queue and the existing queue has to be freed. The QoS Manager requests the
Queue Driver to free the queue.
L2 destination MAC Aged/Deleted
When a L2 destination MAC address is aged/deleted from the pseudo cam, the QoS Manager is notified.
QoS Manager checks to see if any QoS Policy was configured for this MAC address. If so it checks to see
if the queue associated with this MAC is used for any other flows. If not the QoS Manager requests the
Queue Driver to free the queue.
L3 PseudoCAM Entry Aged/Deleted
When a L2/L3 pseudo cam entry is aged/deleted, the QoS Manager is notified. QoS Manager checks to see
if any QoS Policy was configured for this L2/L3 flow. If so it checks to see if the queue associated with
this flow is used for any other flows. If not the QoS Manager requests the Queue Driver to free the queue.
Request to Free Queues Sent to QoS Manager
Request for freeing some qos queues, when there are no sufficient queues available for allocating for link
aggregation, is sent to the QoS.
Link Goes Up/Down
When a link goes up or down the qos requests for freeing/adding the QoS queues associated with those
ports if any policies exists on those ports.
page -10
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Link Aggregation
Link Aggregation
Link Aggregation feature allows software to aggregate a set of ports (not necessarily contiguous or on the
same Coronado) into a group. Each port is referred to as a channel that can carry some bandwidth. This
feature requires that all the queues associated with all the ports in the group to be contiguous. Events
resulting in Link Aggregation and Q driver interaction may be for the creation and deletion of link aggre-
gation group.
Coronado Tables
Coronado maintains two different kinds of tables:
• Layer 2 Tables
• Layer 3 Tables
Layer 2 Tables
• 64,000 pseudo CAM entries are split in 2 tables:
• L2-Source Address (L2-SA) Table containing
• VLAN membership (GID)
• Value (MAC address)
• 2-L2-Destination Address (L2-DA) Table containing
• VLAN Membership (GID)
• Value (MAC address)
• Destination Queues to use (QID/ReQID)
• Priority Description Index (PDI) containing Internal Priority
• Request for additional L3/L4 lookup and use of resultant QID
Layer 3 Tables
• 64,000 pseudo CAM entries. A single table is maintained for all the Source and Destination L3
addresses. Entries are based on selected lookup mode.
• Now, the primary functions and the architecture of Source Learning, Hardware Routing Engine (HRE)
and QOS functional blocks will be discussed.
OmniSwitch Troubleshooting Guide September 2005
page -11
Download from Www.Somanuals.com. All Manuals Search And Download.
Source Learning
Source Learning
Coronado ASIC is a ingress classifier that performs Layer 2 hardware table lookups to the VLAN Id corre-
sponds to the incoming packets.
In principle, Coronado will perform a Layer 2 Source Address (L2 SA) lookup based on whether the
incoming port is a tagging or non-tagging port, a copy of the packet is re-queued to the Source Learning
queue for processing if the lookup fails. Coronado then performs a L2 Destination Address (L2 DA)
pseudoCam lookup to find out the destination Queue Identifier (QID) to queue the packet to the egress
port. Coronado always put the packet in the flood queue if the L2 DA lookup fails until Source Learning
updates DA entry.
Source Learning is responsible for managing (creation, update, deletion) MAC address entry in Layer 2
pseudoCam hardware source and destination address tables and communicating other interested entities
(QOS, Layer 3,...) regarding the new learned mac address.
By taking advantage of the Coronado hardware processing capabilities, Source Learning is distributed on
every Coronado in the switch. The processing load is spread among all the Coronados, thus performance is
increased. On the other hand, Address Learning is independent from the presence of CMM.
Each Coronado sends an event to the CMM to update the filtering database on CMM whenever there is an
operation on its Source Address pseudoCam. As a result, each Coronado has a local view of layer 2
pseudoCam information of its own slot/slice, and the software filtering database on the CMM has global
view of the layer 2 pseudoCam information in the switch.
page -12
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Routing Engine (HRE)
Hardware Routing Engine (HRE)
This feature is responsible for managing the Coronado HRE resources that perform IP and IPX packet
classification and forwarding.
This functionality employees five principal Coronado resources—header cache entries, pseudo-CAM
entries, hash function registers, modes, and router MACs.
Header Cache Entries
Contain the information necessary to modify and forward a packet, including both modifications to the
packet’s content and Coronado-specific handling information.
Pseudo-CAM Entries
Used for classifying traffic based on its IP or IPX address information and, in the case of IPMS, some
layer 2 information. The HRE does not have Content Addressable Memory (CAMs) for storing address
information. Instead it uses hash tables (called pseudo-CAMs) that can be interpreted by the Coronado.
The entries in these hash tables contain both address information to be matched against the content of the
packet and the resulting action to take when the entry is matched. There are two basic actions:
• Forward the packet using information in a specified header cache entry.
• Perform another refining lookup to match additional, more specific address information.
Hash Function Registers
Used to define the hash algorithms used to lookup pseudo- CAM entries in the hash tables.
Modes are used to govern the classification process:
Mode 0
Mode 1
Mode 2
For IP entries, full IP destination host address. For IPX, destination
network number.
For IP entries, full IP destination and source host addresses. For IPX,
not used.
For IP entries, full IP destination and source host addresses and TCP/
UDP destination port number. For IPX, IPX destination network
number and IPX destination node.
Mode 3
For IP entries, full IP destination and source host addresses and TCP/
UDP destination and source ports. For IPX, not used.
Mode 4
Mode 5
Only used for IP firewalling. Uses same matching criteria as Mode 3.
Only used for IPMS. Matches full IP destination and source host
addresses, source port number, and source VLAN identifier.
Mode 6
Unused.
They identify which hash table is to be used, which hash function is to be used, and what portions of the
address information in the packet are required to match that in the pseudo-CAM entry. There are seven
modes, each represented by a configuration register. Some of these have special meaning. For example,
mode 0 is the initial mode. Each packet classification starts in this mode. Each pseudo-CAM entry that has
as its action to perform another lookup includes a number representing the mode to be used in that subse-
quent lookup.
OmniSwitch Troubleshooting Guide September 2005
page -13
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Routing Engine (HRE)
Router MACs
Helps identify candidate traffic for classification. The HRE only operates on traffic that is identified as
requiring layers 3 and 4 classification. Candidate traffic for such classification must be of the type IP or
IPX and must have its layer 2 destination MAC be a router MAC for this switch or be a bridged MAC that
has been marked for layer 3 and 4 classification or be an IP multicast MAC. This feature only manages
router MACs. Bridged MACs are managed by layer 2 source learning and IP multicast MACs are
managed by the IP multicast routing and switching (IPMS) feature. These resources are used to imple-
ment the forwarding features - IP and IPX unicast routing, IP multicast routing and switching, bridging
based on layers 3 and 4 information, and IP firewall.
IP and IPX Unicast Routing
When an IP or IPX packet is addressed to a router MAC on the switch, the HRE attempts to classify the
packet using data in the pseudoCAMs. If a match is found, the packet is updated and forwarded using
information from header cache entry. If not, the packet is routed using one of two default header cache
entries (one each for IP and IPX). These are configured to route the packet to either the IP or IPX soft-
ware process on the Coronado.
IP Multicast Routing and Switching
When an IP multicast packet is received, the HRE attempts to classify the packet using data in the pseudo-
CAMs. If a match is found, the packet is sent to egress processing which uses the information stored in the
header cache entry as well as other Coronado tables updated by the IPMS feature to forward the packet. If
no match is found, the packet is forwarded to the IPMS software process on the Coronado.
Bridging Based on Layer 3 and 4 Information
When an IP packet is addressed to a MAC with an entry in the layer 2 DA pseudo-CAMs that indicates the
treatment for the bridged packet depends on layer 3 and 4 information, the HRE attempts to classify the
packet using data in the pseudo-CAMs. If a match is found, the packet is not modified but is forwarded
using information from the header cache entry. If a match is not found, the packet is forwarded to the QoS
software task.
IP Firewall
The HRE has the capability to match TCP traffic with particular flag bits set. This capability can be
enabled based on the destination MAC of the packet, the destination host IP address of the packet, or the
final matching pseudo-CAM entry for a flow. When this is enabled and the packet has the appropriate flag
bit set, the packet is forwarded normally and a copy is sent to the IP software process on the Coronado.
page -14
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
QoS/Policy Manager
QoS/Policy Manager
Policies describe subsets of traffic, and what to do with that traffic. The Policy Processor determines what
policies are enforceable, and organizes the policies into lists used by the classifier. QoS uses the same
policies for Prioritization/Shaping, IP Filtering (ACLs), NAT, and IPMS Filtering. Using the same poli-
cies for all these functions has several benefits:
• All policies affecting the traffic are centrally located
• All policies share the same expressive power.
• Traffic is only classified once in a single routine.
• A single GUI application (PolicyView) can manage policies, and subsequently manage all these facili-
ties.
QoS determines which policies can possibly be matched on a switch, and constructs lists for each of the
L2 and L3/L4 classifiers. If a policy contains classification criteria that cannot be met by the hardware,
QoS logs a message indicating what parameters could not be matched, and the policy is not used in classi-
fication.
The QoS manager calls the classifiers in response to messages from source learning, routing, and IPMS.
QoS uses lists maintained by the QoS Policy Processor to make it’s decisions.
Coronado Egress Logic
• Coronado receives a packet from the Fabric through FBUS destined for a Queue existing on the same
Coronado. There is not a lot of egress Logic to be performed for Unicast packets.
• If the destination port is untagged, 802.1Q tag is stripped and the packet is forwarded to the destina-
tion port.
• Coronado limits the flood bandwidth or Flood and Multicast Bandwidth per port. Bandwidth limita-
tion is based on dual leaky bucket algorithm. Packets are credited in chunks of 64 bytes every
130.98us.
• IPMS processing is completed by the Coronado on the egress, started by the HRE.
• Updates IPMS routed packets- decrements TTL and rewrite MAC-DA.
• Duplicates the packet whenever needed. Multicast packets are duplicated by the software on a Q-Tag
link.
OmniSwitch Troubleshooting Guide September 2005
page -15
Download from Www.Somanuals.com. All Manuals Search And Download.
The Fabric Architecture
The Fabric Architecture
ASIC provides the switching fabric functionality for the OmniSwitch Series. The switching fabric does no
frame processing and does not distinguish between L2 switching and L3 routing. The fabric provides only
a limited amount of FIFO buffering for each port, flood and the multicast queue. Most of the system buff-
ering is in the Ingress Coronado’s Queue Manager. The backplane fabric is a bit-sliced ASIC. Each chip
contains a control element and data buffering and queuing logic. All fabrics in the primary fabric operate
in a lock step under control of the “master” fabric. The fabric provides one unicast queue for each physi-
cal port on the OmniSwitch Series plus broadcast and multicast queues and, inter-processor communica-
tion queues. Switching Fabric monitors the depth of its on-chip queues and provides flow control feedback
to the Coronado ASICs. Switching fabric also generates control messages for each of four priorities to
drive the Coronado bandwidth control. The backplane is wired like a wagon wheel where the fabric card is
the “hub” and the point-to-point backplane connections are the spokes. Each network interface card (NI) is
at the end of a spoke. Each NI is connected to the redundant fabric by an identical but separate set of
connections. For redundancy, each NI slot is wired to both fabric cards by separate traces.
OS7XXX and OS8800 use different Fabric ASICs for the backplane connectivity between all the slots:
• OS-7XXX uses Nantucket ASIC
• OS-8800 uses ROMA ASIC
page -16
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Nantucket ASIC
Nantucket ASIC
The Nantucket ASICs have the following:
• Support for 8 and 16 Coronados only.
• No dynamic queue numbering for each NI slot.
• Fixed eight Nantuckets per Fabric board.
• Maximum of one redundant Fabric board.
The Nantucket software is arranged as:
• Nantucket operational software resides on the CMM.
• Nantucket operational software runs on the UltraSPARC IIe on the CMM.
• All accesses to Nantucket registers is through the PCI bridge and over the Bbus bridges.
• Minimum user interface software is provided for configuring and statusing the Nantucket ASICs.
• Minimum SNMP software is provided for configuring and statusing the Nantucket ASICs.
Additional Nantucket Specifications
• Nantucket Fabric consists of eight Nantucket ASICs for the primary Fabric in OS-7800 and four
Nantucket ASICs for the primary Fabric in OS-7700.
• Nantucket Fabric consists of eight/four Nantucket ASICs for the redundant Fabric, when running with
a redundant CMM.
• Nantucket uses six SRAM memories, each SRAM is 32 bits wide by 11264 words deep.
• Nantucket has a point to point interface to all Coronados running at 500MHz.
• No packet processing on Nantucket
• Provides very little buffering
• Supports 512 per-port queues
• Supports 1 per-Coronado broadcast queue and 1 intercommunication queue.
• Supports flow control/pay generation for Coronado bandwidth control
• Supports VLAN spanning tree masks
Nantucket supports the following messages:
• Ingress packets w/header
• Egress packets w/header
• Flow control messages
• Bandwidth management control messages “pay.”
OmniSwitch Troubleshooting Guide September 2005
page -17
Download from Www.Somanuals.com. All Manuals Search And Download.
Nantucket ASIC
Functional Description:
The Nantucket software resides on Chassis Management Module (CMM) and run on the UltraSPARC IIe
processor within the CMM. The Nantucket software communicates to the Nantucket ASIC via the PCI
Bridge and Bbus Bridges. The Nantucket Software has interfaces to the following:
• Primary CMM SDRAM, EEPROM via the UltraSparc IIe PCI Bridge
• Secondary CMM EEPROM via the UltraSparc IIe PCI Bridge
• 2 Primary Fabric Board Burst Bus Bridges via the UltraSparc IIe PCI Bridge
• 2 Secondary Fabric Board Burst Bus Bridges via the UltraSparc IIe PCI Bridge
• 8 Primary Fabric Board Nantucket ASICs via two Burst Bus Bridges
• 8 Secondary Fabric Board Nantucket ASICs via two Burst Bus Bridges
• Primary and Secondary Fabric Board Flash and Backplane EEPROM via the Burst Bus Bridge.
Data Flow
The following describes the data flow of unicast, Multicast and IP packets through the major modules of
the Nantucket ASIC:
• Receives serial input from Coronado at 500MHz
• Outputs 4 bit parallel data at 125MHz to the Data Port Input module
• Separates the 4 bit parallel input from the XyPhy input module into data and control streams.
• Send 192 bit data chunks to the Memory Manager module.
• Send chunk present, start of packet (SOP) and coupons to the Packet Chainer module.
The Packet Chainer Module performs:
• Processes incoming packet chunks from the Data Port Input module.
• Sends SOP, chain ID and packet type (unicast or multicast) to the Queue Manager module.
• For unicast and uP packets, decode the QID and pass the QID to the Queue Manager module upon
EOF.
• For multicast packets, decode the QID and pass to the Queue Manager module upon EOF.
The Queue Manager Module performs:
• Enqueues packets controlled by the Packet Chainer module, links the chain to the unicast queue or
copy the packet head pointer into multiple multicast fifos.
• Dequeues packets controlled by the Calendar Manager module from one of 512 unicast queues or one
of 16 multicast queues.
• Generates four paycheck messages for each physical port every 32.7 us denoting if measured queue
depth is above or below the pay threshold values.
• Generates a per physical port coupon message every 2us to the ingress Coronado denoting if measured
queue depth is above or below the coupon threshold value.
page -18
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Nantucket ASIC
Calendar Manager Module
• Generates dequeue requests to the Queue Manager module with priorities of uP packets highest, multi-
cast packets second highest and unicast packets lowest.
• Request dequeues from 512 unicast queues by sending a QID.
• Request dequeues from uP queue by sending FIFO ID.
• Calendar for a Coronado with 24 10/100 ports would be: 0,1,2,3,4,5,6,7,8,9,...,23.
• Calendar for a Coronado with 12 10/100 ports and 1 Gigabit port would be:0,1,0,2,...9,0,10,11,12.
• Memory Manager Module
• Interfaces between the six SRAMs (32x11264 words) and the data ports.
• Assigns packet chunks to free buffers.
• Queues buffer pointers in per-port queues.
• Returns free buffers to the free buffer list.
Data Port Output Module
• Combines data and control streams into nibble wide output.
• Transmit to the XyPhy Output module (B09) at 125MHz.
• XyPhy Output Module
• Serializes nibble wide input from the Data Port Output module (B08).
• Transmits serial output at 500MHz.
Nantucket Redundancy
• The Redundant/Secondary Fabric Board Nantucket ASICs initialize at startup and initialize prior to
any Primary Fabric Board failures.
• The Nantucket software monitors and detect Primary Fabric failures which includes Fbus link failure,
no frames received, no backpressure/paychecks received, no calendar pointers are updated, etc.
• When a failure condition is detected that requires switchover to the Secondary Fabric, the Nantucket
software writes to a register to cause the primary/secondary signal to the Coronado to transition to’0’.
• This will simulate to the Coronado the Primary Fabric being removed.
• The Coronados detect the primary/secondary deasserted signal and perform the failover procedure.
• The method allows all Coronados to switchover at that same time.
OmniSwitch Troubleshooting Guide September 2005
page -19
Download from Www.Somanuals.com. All Manuals Search And Download.
Nantucket ASIC
Coronado
Nantucket 0
Nantucket 1
Nantucket 2
Nantucket 3
Coronado
Coronado
Coronado
Coronado
Coronado
Nantucket 0
Nantucket 1
Coronado
Coronado
page -20
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Nantucket ASIC
OS-7700
Backplane
Nantucket 0
Nantucket 0
Coronado
Coronado
Nantucket 3
Nantucket 1
Secondary CMM
Coronado
Coronado
Coronado
Nantu
Coronado
Coronado
Coronado
Nantu
Nantucket 2
Nantucket 3
Nantucket 3
Coronado
Coronado
Coronado
Nan
Nantucket 4
Coronado
Coronado
Nantucket 5
Nantu
Nantucket 6
Nantucket 6
Coronado
Coronado
Nantucket7
Nantucket 7
Coronado
Every Coronado is connected to Primary CMM and secondary CMM with all the
Nantuckets. Maximum of 16 connections to Coronado can exist on each Coronado.
OS-7800 Architecture
OmniSwitch Troubleshooting Guide September 2005
page -21
Download from Www.Somanuals.com. All Manuals Search And Download.
Roma
Roma
Each Fabric Module is based on two Roma ASICs, which provide the store-and-forward switching fabric
function for the OS-8800 product. The Roma ASIC is bit-sliced; a group of eight Roma ASICs operates
together as a single synchronized fabric. A total of four Fabric modules are required to build a complete
Fabric in the OS-8800 system. An optional fifth Fabric Module may be used for fabric redundancy. In a
group of eight Roma ASICs, there is always one master and seven slaves. These ROMA ASICs are located
on Switch Fabric Modules at the rear of the chassis.
The SFM module consists of two identical fabric slices. Each fabric slice consists of one Roma ASIC.
There is also a bridge FPGA that interfaces the on-board ASICs to the CMM modules through the BBUS
management bus. Major SFM elements are the following:
• Two Roma ASICs
• One Bbus FPGA
• One DC-DC Converter
• Reset Circuitry
• Clock Circuitry
• Power Fail Detect/ Uncontrolled Power Failure Circuitry
Following is the fabric hardware environment:
• The Roma-based fabric always operates using a set of eight Roma ASICs
• The eight operational Roma chips must be numbered according to bit slice position
• An additional two hot-standby Roma ASICs can provide for fabric redundancy
• Two Roma ASICs per separately insertable card, five fabric slots per Eagle chassis
• 64 fabric ports per Roma ASIC (supports up 64 Coronado ASICs or 16 Calais ASICs)
• Support for any architecturally coherent combination of Coronado and Calais ASICs
• 512 logical ports per system corresponding to Roma queues (maximum)
• 384 physical ports per system corresponding to Roma unicast queues (maximum)
• 64 IPC queues per system (maximum)
• 64 multicast FIFOs per system (maximum)
• 24 physical ports per NI slot (maximum)
• Calendar mechanism for dequeuing unicast and multicast frames
• Multicast (VLAN) vector table for multicast propagation control
• Greater than 500 MHz raw link rate per fabric port (each direction)
• 2.4 Gbps per Coronado
• 10 Gbps per Calais (or equivalent replacement hardware)
• Four paycheck levels to support flow prioritization
page -22
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Roma
• Separate paychecks for multicast
• Generates ingress coupons, receives egress coupons for backpressure capability
• Ingress coupon generation period: ~2 microseconds
• Paycheck generation period: 32.125 microseconds
• The BBUS provides access to individual Roma chips based on a chip index number
Functional Description
The Roma Driver’s primary responsibilities are to initialize, monitor, and support the central component
of the Eagle switch/router’s switching fabric system: a set of up to ten Roma ASICs, with exactly eight
operational during fabric operation.
The operational fabric consists of 8 slices for each connected Coronado ASIC (these 8 slices correspond
one-to-one with the 8 operational Roma ASICs). The fundamental logic for packet switching through the
fabric is contained in 5 basic architectural components:
• Link Control
• Calendar
• Multicast Vector Table
• IPC Mapping
• Flow Control
Link Control
This establishes that Roma-Coronado communication is working on each link and is aligned across the 8
fabric bit slices.
Calendar
Each fabric port has a calendar of unicast and multicast egress destinations for the corresponding Coro-
nado. There is a limited ability to designate dequeuing frequency for some destinations, affecting the
egress bandwidth allocated to destinations. During a given cycle of the Primary Cycle, a single calendar
entry for each fabric port is processed (in a specified order). During other cycles, other calendar entries are
processed. IPC packets are given absolute priority, so there are no calendar entries for IPC.
Multicast Vector Table
Indicates multicast domain membership for fabric ports. On fabric ingress, frames are put into a given
fabric port’s multicast FIFO based on this vector.
IPC Mapping
On ingress, Coronado IPC QIDs are identified based on agreed upon values (for Roma the values are
selected from offsets 12 through 15). On egress, an internal Roma table maps IPC QIDs to fabric ports
(one-to-one).
OmniSwitch Troubleshooting Guide September 2005
page -23
Download from Www.Somanuals.com. All Manuals Search And Download.
Roma
Flow Control
Coupon and paycheck thresholds are set for unicast and IPC queues (multicast is limited by Coronado for
fabric ingress). These thresholds are used to generate ingress backpressure and paycheck messages. Each
Roma ASIC participating as an operational bit slice is responsible for 2 NIs according to the scheme: bit
slice n is responsible for NI slots 2(n+1) and 2(n+1)-1. Bit slices are zero-based (0 - 7); NI slots are one-
based (1 - 16).
In order to support basic system operation, the Roma driver must maintain the correct destination port
mapping on the Roma ASIC chips, including any required multicast and IPC port mapping; appropriate
internal flow control thresholds should be maintained as well. These form a small but significant part of
the initialization process and the Roma driver needs to adapt in case of changes to NI slot configuration.
However, the high level sequencing and selection of Roma Driver activity is mostly a function of a set of
external events, most of which can be termed “hot swap” events. The following 10 scenarios represent
high-level states for the Roma Driver which correspond to its handling of some kind of major.
Initialization
This state is entered when the Roma Driver is first spawned as a task on the primary CMM. Early on, the
fabric slot and NI slot configuration must be completely determined to effectively program the Roma
ASICs. An overview of the ASIC setup follows:
• Bit Slice oriented setup - includes programming chip IDs and master chip selection.
• Fabric Port setup - includes calendar, flow control, and multicast vector setup
• Synchronizing Roma chips - includes starting primary cycle and timer resets
• Manual link acquisition - verify that all links are up, includes retries
• Automatic HW recovery mechanism setup - includes link acquisition and hot swap
• During switch operation, this is the state that the Roma Driver will be in the vast majority of the time.
Remaining in this state implies there are no changes to: physical Fabric slot configuration, NI slot
configuration, the primary CMM slot, or detected framing errors. Processing in this state consists of an
infinite loop where the following tasks are performed:
• Respond to interrupts and use low intensity poll for backup
• Check messages for updates to multicast vector and board changes
• Synchronize the multicast vector shadow table when 2 CMMs are present
• Maintain statistical counts and rates
Fabric Slot Insertion
This state assumes that four operating fabric slots are currently occupied. The state is entered when a fifth
fabric card is inserted into the remaining available slot. This card should not disturb the operational fabric,
and it will assume the role of redundant fabric card.
page -24
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Roma
Fabric Slot Extraction
This state assumes that there are five fabric slots occupied, with one fabric card serving as the redundant
card. Roma Driver will have already set up the operational Roma chip set to use built-in hot swap
handling. Upon extraction of fabric card, most of the hot swap handling is done by Roma ASIC logic. The
performs the following tasks when a fabric card is removed:
• Recover the new fabric slot set state since the operational fabric may change.
• Report fabric slot states to Chassis Supervision.
• Change hot swap settings on the master since a standby slot is no longer present.
• On operational fabric set changes, update flow control settings.
NI Slot Insertion
When a new NI card is inserted, Roma Driver will attempt to disturb existing fabric traffic as little as
possible. The following tasks are performed: Remove perpetual coupons for NI.
Setup Calendars and Flow Control for New NI
• Restart Calendar Manager.
• Enable transmit and take internal blocks out of reset for NI.
• Acquire links to all Coronados on the NI.
NI Slot Extraction
When an NI card is extracted, Roma Driver performs the following tasks:
• Set perpetual coupons to drain traffic for NI.
• Disable transmit and put internal blocks in reset for NI.
• Remove auto link acquisition mechanism for NI.
CMM Takeover and Hot Swap
Following a good takeover or CMM hot swap, the primary objective of the Roma Driver is to disturb the
Roma ASICs as little as possible. If the takeover results in an irrecoverable fabric-related failure, the
driver attempts to detect this condition and execute a “reload all” to the chassis. The following tasks are
performed:
• Recover the new fabric slot set state since it is unknown to the secondary driver.
• Monitor the Roma ASIC registers to detect fatal error condition.
• Send reload all message to chassis supervision if fatal error detected.
OmniSwitch Troubleshooting Guide September 2005
page -25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chassis Management Module (CMM)
Framing Error
The Framing Error event represents an event where the Roma ASIC detects an error in a packet header on
ingress. Since this will potentially corrupt the buffer system, a free list rebuild is required when this is
detected.
Coronado
Coronado
Up to 64
Coronado
ASICs can
Be connected to
.
.
.
Total of 8
ROMAs are
active at a
time
.
ROMA
Coronado
Coronado
OS-8800 Switching Fabric
Chassis Management Module (CMM)
Chassis Management Module (CMM) controls the major functionality and synchronization between two
different components in the distributed architecture. The main responsibilities of the CMM for both
OS7XXX and OS8800 are the same:
• Booting up all the modules in the chassis.
• Downloading the customer specific configurations on the NI.
• Synchronization of the fabric modules
• Power distribution
• Switch diagnostics
• Important availability features, including redundancy (when used in conjunction with another CMM),
software rollback, temperature management, and power management.
• Providing access to the switch through Command Line Interface (CLI), Web management and SNMP
• Provides an out of band Ethernet Management Port (EMP)
page -26
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Chassis Management Module (CMM)
OS7000 CMM
The CMM for OS7000 contains the following:
• System Processor
• Ultra Space 11e (400MHz)
• 64MB SDRAM Memory
• Switching Fabrics
• 4 Switching fabrics, Nantucket, in OS-7700
• 8 Switching fabrics, Nantucket, in OS-7800
• Management
• DB-9 console/modem Port
• RJ45-Out of Band 10/100 LAN Port
• Reset Switch
• Hot Swappable
• Up to 2 CMMs per chassis
• Management redundancy
• Switching Fabric Redundancy
OS8800 CMM
The CMM for OS8800 contains the following:
• System Processor
• Ultra Space 11e (400MHz)
• 64MB SDRAM Memory
• Management
• DB-9 console/modem Port
• RJ45-Out of Band 10/100 LAN Port
• Reset Switch
• Hot Swappable
• Up to 2 CMMs per chassis
• Management redundancy
OmniSwitch Troubleshooting Guide September 2005
page -27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chassis Management Module (CMM)
Functional Description of CMM
Software and Configuration management is implemented in such a way to provide the operator with:
• Flexibility
• Resiliency
• And to minimize the service interruption during the update of a network.
• 2 Software versions are stored into flash:
• 1 working version: operational release, used for upgrades.
• 1 certified version: operator validated trusted release.
• Automatic rollback from the working version to the certified version in case of failure of the working
version.
• Possibility to certify a version when the operator has considered its behavior acceptable
• All of the files making up the “working” software release must be contained in “/flash/working” direc-
tory.
• All of the files making up the “certified” software release must be contained in “/flash/certified” direc-
tory.
• The “boot.params” file stored in “/flash” is the configuration file that contains the system boot parame-
ters as well as the Image Rollback variables. The two software releases use the same boot parameters
and Image Rollback variables.
• New software version can be activated by loading the images in “/flash/working” and rebooting the
switch in working directory using the command “reload working no roll-back timeout”
• A running “working” version can be certified any time after the “working” version is loaded and veri-
fied.
• The configuration file of a certified software version cannot be modified while working with “certi-
fied” version.
• If the working version is certified and the switch is rebooted or reboots for any other reason, it will
boot up in the new certified version.
• If the working and certified versions of code as well as configurations are completely synchronized the
switch will boot up in certified directory but the running directory will be set to “working”. This flexi-
bility allows to modify configurations and save them. Certification of the new configurations will be
required to save the configurations in certified directory.
CMM Software Startup Process
CMM startup process consists of the following steps:
• Boot ROM
• Vx Works Flash File System
• MiniBoot
page -28
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Chassis Management Module (CMM)
AOS
Boot ROM
• Sparc Processor executes the Sparc Boot ROM code from flash Memory in the protected memory.
• Performs minimum diagnostic tests of the Sparc Processor
• Verifies memory used by Sparc Processor is fine
• If the diagnostic tests find an error, the CMM/Fabric LED will flash to indicate the error and the
processor will retry to boot.
• Boot ROM is not field upgradeable
• Boot ROM image contains:
• Access to Flash File System (FFS)
• Zmodem
• IP stack for EMP Port
• FTP code
Note. Sparc Boot ROM loads the miniboot from the FFS in non protected area of the Flash Memory.
OmniSwitch Troubleshooting Guide September 2005
page -29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chassis Management Module (CMM)
MiniBoot
MiniBoot contains VX Works Operating system
Performs the following tasks:
• Post Mortem Dump (PMD) Processing to save as much diagnostic as possible in the FFS after a system
crash.
• Hardware diagnostics to determine if all the boards are operational at boot time.
• Image Rollback to select either the current uncommitted (working) software release or the previously-
committed (certified) release.
• Loads the VX Works and passes the control to VX Works
• On error, the miniboot returns to the “Boot ROM” step to allow the user to load new software into the
flash memory.
AOS Start
AOS executes to initialize and start up the system based on the command file which contains:
• Socket Send mechanism: allows sending messages to all CMM and NI processors in the Falcon
• The System services fault management code
• The System services timer facility
• The chassis manager
• Specific services like telnetd, ftpd, cli and snmp
Chassis Manager Component of System Services
• Discover the number of slots, daughter boards, power, temperature and other environmental factors
• Discover the NI boards
• Discover the primary/backup processor status of CMM. If secondary then does not load NI boards and
all processes are started in secondary mode.
• AOS startup code selects the modules to load from the FFS.
• After starting all services System Services Fault Manager acts as a “health monitor” and exchanges
messages with objects in the system to make sure they are working properly.
CMM Reload of NI Module
CMM reloads the NI when:
• CMM Chassis Manger detects a board that does not have the images loaded.
• User enters explicit command to reload the NI.
• CMM fail over happens and the configurations/images were not synchronized between Primary and
Secondary CMM.
page -30
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Chassis Management Module (CMM)
Running Version
Flash Files
/flash/boot
Boot ROM
Miniboot
Load Minimum VX Works
with
(Hidden & Protected)
Execute
MiniBoot
1-Default
File system with PMD
process.
Read/Write
2-Backup (Write Protected)
Boot.cfg determination and
Boot.cfg
………
Contains boot
Read
Boot
LOAD VXWorks with File System
/flash
Chassis Manager
/working
CLI
SNMP
HTML
/certified
Read/Write
/log
/pmd
OmniSwitch Troubleshooting Guide September 2005
page -31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chassis Management Module (CMM)
Software Management
Command Fos
Configuration Save
Version Activate
Version Restore
Version Certify
Version Query
BBUS
Falcon Overall Block Diagram
•
NI
NI
NI
NI
………
FBUS
Nantucket
Nantucket
Nantucket
..
..
Secondary CMM Board
Primary CMM Board
…. Secondary
…. Primary
Overall System Architecture
• Fabric resides on CMM
• Number of Nantuckets can be 4 or 8 depending on the chassis
• Fabric Bus is connected to the CMM as well as to the All NI
• Burst Bus (BBUS) is connected to all the NI from the CMM
• CMM and Switch redundancy fail-over simultaneously
• Up to 16 Coronados can be connected to each Nantucket
page -32
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Chassis Management Module (CMM)
Eagle Overall Block Diagram
•
Fabric Boards
Redundant Fabric Module
FBUS
….
CMM
BBUS
CMM
…. Secondary
…. Primary
• Fabric resides independent of the CMM. It resides at the Back of the Chassis. CMM can fail over inde-
pendent of Switching Fabric and vice versa.
• Minimum of 4 Switching Fabric Modules (SFM) with 8 ROMS chips are required to operate. The
additional SFM provides (4+1) redundancy.
• FBUS is not connected to the CMMs
• BBUS is connected to both the CMMs and all the NI in the chassis including the SFMs.
• Up to 64 Coronados can be connected to each ROMA
OmniSwitch Troubleshooting Guide September 2005
page -33
Download from Www.Somanuals.com. All Manuals Search And Download.
Packet Walk
Packet Walk
Packet Walk Principles
• All switching and routing is performed on the Ingress side of the switch. There are no address lookups
made on the Egress side.
• The Coronado combines the L2 switching and L3 routing logic into the same ASIC.
• Data always flows through the Nantucket even if the source and destination ports are on the same
Coronado.
• As indicated the “switching fabric” functionality is provided by Nantucket ASICs. The Nantucket
ASICs set also performs part of the broadcast/multicast processing by sending copies of multicast
packets to each Coronado in the system, and participates in the priority de-queuing logic.
Data Flow Overview
• Data flows in a 10/100 Mbps or Gigabit Ethernet port through the Catalina MAC ASIC and into the
Coronado ASIC.
• The Coronado’s HRE-X (Hardware Routing Engine) performs CAM (Content Address Memory) look-
ups on the source and destination addresses and selects a QID (queue ID) to switch the frame. The
queue selection is based upon L2 or L3 switching/routing criteria plus QoS priorities. The Coronado
ASIC can manage up to 2,048 queues. The Coronado could also queue up some frames for software
processing by the on-chip Sparc CPU for some specific unknown packets, which requires a particular
treatment.
• The Coronado’s Queue Manager then de-queues the frame from the appropriate queue based upon
destination and priority. The frame is output from the Coronado into the Nantucket switching fabric.
• The Nantucket provides minimal buffering and delivers the data to the destination Coronado for Egress
processing. Note that the destination Coronado can be the same Coronado or it can be different.
• The Coronado Egress processing sends the frame to the output port via the Catalina Ethernet inter-
faces. Notice that there is no CAM lookup processing or software processing during Egress. The Egress
processing logic also handles multicast processing in cooperation with the Nantucket.
page -34
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Specific Packet Flows
Specific Packet Flows
Unknown L2 Source, Known L2 Destination
The Catalina ASIC
Packet arrives at Catalina. CRC check done. If valid CRC it is put on XYBUS to Coronado
The Coronado ASIC
• The FIFO logic maintains queues of frames from both Xybus interfaces and selects an incoming frame
for HRE processing. This FIFO is done on the on chip memory of the HRE.
• The parser logic selects fields from the frame to identify the protocol and find key values that are used
by the HRE for lookups (DA, SA)
• Coronado does a L2 SA pCAM lookup.
• Coronado determines this is an unknown source due to failed lookup in L2 SA table.
• Since the SA is unknown, there is no pCAM entry, so the default Group ID (VLAN) is used
• If the port is secured then the frame is not forwarded
• The packet is requeued to NI SPARC, for software processing.
• Software creates an entry into the L2 SA table with packet’s mac address and Group ID
• Coronado checks for special L2 DA (ARP, STP, IGMP, IPMS, Router)
• Since the frame is known is present in the L2 DA table for that NI, the L2 entry provides the destina-
tion QID as well as the PDI (internal priority).
• Access the PDI and select internal priority.
• Enqueue the data to the final QID. The QID determines the destination port, priority and bandwidth.
• Coronado’s queue manager dequeues the frame based upon destination and priority. The frame is
output from the Coronado into the Nantucket switching fabric via the FBUS.
Note. The Queue Manager will alternately dequeue the Multicast and Unicast Queues.
The Nantucket ASIC
The Nantucket provides minimal buffering and delivers data to the Coronado for egress processing.
The Coronado ASIC
• The Coronado receives the packet via the FBUS.
• The Coronado then strips the 802.1q header that was added on ingress, if needed.
The Catalina ASIC
• Packet is then put on to the Xybus to be received by the Catalina.
• Catalina Egress will generate the CRC and regulate the packet framing including the interpacket gap.
OmniSwitch Troubleshooting Guide September 2005
page -35
Download from Www.Somanuals.com. All Manuals Search And Download.
Unknown Destination
Unknown Destination
Known L2 Source, Unknown L2 Destination
The Catalina ASIC
Packet arrives at Catalina. CRC check done. If valid CRC it is put on XYBUS to Coronado
The Coronado ASIC
• The FIFO logic maintains queues of frames from both Xybus interfaces and selects an incoming frame
for HRE processing. This FIFO is done on the on chip memory of the HRE.
• The parser logic selects fields from the frame to identify the protocol and find key values that are used
by the HRE for lookups (DA, SA)
• Coronado does a L2 SA pCAM lookup.
• Coronado determines this is a known source and retrieves Group ID.
• Coronado checks for special L2 DA (ARP,STP,IGMP,IPMS,Router)
• Coronado performs L2 DA pCAM lookup based on Group ID.
• Because the L2 DA is unknown on that NI, the lookup fails.
• Coronado sets the QID to the flood queue, and the PDI to the unknown_DA and ReQId is set to Soft-
ware queue for unknown_DA. 802.1Q header is added.
• Enqueue the data to the final QID. In this case the QID is 511. The QID determines the destination
port, priority and bandwidth.
• Coronado’s queue manager dequeues the frame based upon destination and priority. The frame is
output from the Coronado into the Nantucket switching fabric via the FBUS.
• Note the Queue Manager will alternately dequeue the Multicast and Unicast Queues.
The Nantucket ASIC
• The Nantucket sends the packet to all egress Coronados, that have the bit set in the VLAN flood vector
for this Group ID.
• The Nantucket provides minimal buffering and delivers data to the Coronado for egress processing.
page -36
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Unknown Destination
The Coronado ASIC
• The Coronado receives the packet via the FBUS.
• The Coronado then strips the 802.1q header that was added on ingress, if needed.
The Catalina ASIC
• Packet is then put on to the Xybus to be received by the Catalina.
• Catalina Egress will generate the CRC and regulate the packet framing including the interpacket gap.
• The above delivers the first few packets of a flow that has an unknown destination via the flood queue.
Traffic is Being Passed; the Switch is Attempting to Put a
Correct L2 DA Entry on the NI
The Coronado ASIC
• Ingress Coronado sends IPC messages to all active Coronados on the BBUS inquiring about the desti-
nation address. All the active Coronados look into their L2SA table and if they have a matching entry
then they sends the Group ID, Mac address, QID, PDI, and request for additional L3/L4 lookups to the
Ingress Coronado.
• Once this information is put into the L2 DA table of the ingress Coronado, the packets are processed as
a known DA and are no longer put on the flood queue.
OmniSwitch Troubleshooting Guide September 2005
page -37
Download from Www.Somanuals.com. All Manuals Search And Download.
Unknown Destination
Unknown L3 DA
The Coronado ASIC
• The FIFO logic maintains queues of frames from both Xybus interfaces and selects an incoming frame
for HRE processing. This FIFO is done on the on chip memory of the HRE.
• The parser logic selects fields from the frame to identify the protocol and find key values that are used
by the HRE for lookups (DA, SA)
• Coronado does a L2 SA pCAM lookup.
• Coronado determines this is a known source and retrieves Group ID.
• Coronado checks for special L2 DA (ARP,STP,IGMP,IPMS,Router)
• This lookup matches a Router, therefore routing is needed.
• Coronado performs L3 DA address lookup.
• This lookup fails and the packet is requeued to the software on the Sparc. (Slow path)
• The L3 DA is compared to the L3 FDB (routing table).
• If this lookup fails, the packet is sent to the default gateway.
• Which ever route the packet matches, the Coronado retrieves the Next Hop Router Cache (NHRC)
Index for this packet.
• The Coronado uses this index, to look up the NHRC and retrieve the QID and PDI.
• The L3 DA table in the pCAM is updated accordingly with this information.
• The frame is output from the Coronado into the Nantucket switching fabric via the FBUS.
page -38
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Unknown Destination
Packet arrives from Catalina to Coronado
Y
Assign
Default GID
and sends to
S/W
N
Pseudo-CAM (PCAM)
Provides Group ID
(GID)
1
Source Address
known ?
2
De Queue packet and
perform PCAM update
Y
Is DA Router MAC,
IGMP, STP, Multicast
Switching
5
Is DA
Special ?
N
Y
Access PDI to assign
internal priority (0…3)
& final QID
Lookup provides QID
& Priority Description
Index (PDI)
4
Is DA
Known?
En Queue data to
final QID, QID
determines
N
destination port,
priority &
bandwidth
A
Egress Coronado forwards the
packet to destination port,
strips Q-tag, if needed.
Queue Manager selects
packet for transmission
to Nantucket, if needed
Nantucket send to other
Coronado, if needed.
Known/Unknown SA and Known DA
A
DA QID is unknown, QID is set to flood,
PDI is set to unknown DA and ReQID is set
for s/w for unknown DA
S/W De Queue s packet. Includes the learning
of MAC DA via request to all other Coronados
Egress logic sends copy of the packet to all
the ports in that vlan. Strips Q-tag if needed.
4
Get final QID
Unknown DA
OmniSwitch Troubleshooting Guide September 2005
page -39
Download from Www.Somanuals.com. All Manuals Search And Download.
Unknown Destination
5
Classify Special DA
DA is STP multicast
(BPDU)
DA is router MAC
DA is IGMP
DA is IPMS
7
6
8
DA PCAM
lookup,
known ?
L3
S/W
Slow Path Routing
FDB?
N
N
Y
Y
Send to Destination
Send to Default
Gateway
Provides a
Next_Hop_Header_Cache index
4
NHHC index provides QID,
ReQID & PDI
Performs NAT, MAC-DA, TTL,
SLB and Fragment modifications
L3 Packet Walk
7
6
DA is IPMS
DA is IGMP
N
New IPMS
group
L3 DA lookup
Pass?
S/W
S/W
Y
QID set
to either
multicast
ReQID
Sent to
S/W for
N
Flow not
known
S/W
within
L3-DA, L3-SA,
pport, sGID
lookup, Pass ?
Y
processing
the vlan
or drop
En Queue the
data to the
final
QID=511
(multicast
Queue on
Nantucket)
Set QID, ReQID, PDI &
header_cache info
Access PDI
Egress Coronado sends to all the ports in the
same vlan, strips tag if necessary
Nantucket sends the packet to all egress
Coronado within the same
multicast/vlan id
IGMP/IPMS
page -40
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Buses on OmniSwitch 7700/7800/8800 Switches
8
DA is STP multicast
(BPDU)
S/W
QID for
flood or
drop
ReQID for
S/W
processing
BPDU
Hardware Buses on OmniSwitch 7700/7800/
8800 Switches
Xybus
The interface between the MAC to Coronado, which is 0-1
Fbus
The interface between the Coronado to the Fabric ASIC (Nantucket or Roma). For the OmniSwitch 7700
(Falcon half chassis) it is 0-7. For the OmniSwitch 7800 (Falcon full chassis) it is 0-15. For the
OmniSwitch 8800 (Eagle) it is 0-63.
Bbus
This the management bridge bus connecting the CMM sand NIs. It is a single bridge bus.
OmniSwitch Troubleshooting Guide September 2005
page -41
Download from Www.Somanuals.com. All Manuals Search And Download.
Bus Mapping on OmniSwitch 7700/7800/8800 Switches
Bus Mapping on OmniSwitch 7700/7800/8800
Switches
Xybus Mapping
Each board type has own mapping, described for all existing board type below.
• OS7-ENI-C24 and OS8-ENI-C24: Single slice board, connects two Catalina MAC ASICs through
xybus0 and xybus1.
• OS7-ENI-FM12: Single slice board, connects one Catalina MAC ASICs through xybus0,
• OS7-GNI-U2: Single slice board, connects two Catalina MAC ASICs through xybus0 and xybus1.
• OS8-GNI-U/C8: Four slice board, each slice connects two Catalina MAC ASICs through xybus0 and
xybus1.
• OS7-GNI-U/C12: Single slice board, connects two Firenze MAC ASICs through xybus0 and xybus1.
• OS8-GNI-C24: Two slices board, each slice connecting two Firenze MAC through xybus0 and
xybus1.
• OS8-GNI-U24: Four slice board, Slice 0 and 2 connecting one Firenze MAC through xybus0 and Slice
1 and 3 connecting one Firenze MAC through xybus1.
Fbus Mapping
Note. Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel.
Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy
network down time and/or permanent damage to hardware.
Falcon (OmniSwitch 7700/7800) Fbus Mapping
-> dshell
Working: [Kernel]->nanListMapping
Full Chassis (OS7800):
Fbus/Nan Port: 0,2,4,6,7,5,3,1,14,12,10, 8, 9,11,13,15
NI Slot:
1,2,3,4,5,6,7,8, 9,10,11,12,13,14,15,16
Half Chassis (OS7700):
Fbus/Nan Port: 0,2,4,6,1,3,5,7
NI Slot:
1,2,3,4,5,6,7,8
Eagle (OmniSwitch 8800) Fbus Mapping
Unlike Falcon, Eagle (OmniSwitch 8800) uses strict fbus number starting from 0 through 63.
Formula: Fbus_number = (slot_number - 1) * 4
For example, a OS8-GNI-U8 in slot 4, (4-1)*4=12. Since the OS8-GNI-U8 is a 4-slice board, Fbus
number starts from 12, up to 15.
page -42
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
OS6624/6648 Architecture
OmniSwitch 6XXX is a stackable version of the OS7/8XXX Switches. It provides pure Ethernet switch-
ing for 10/100 and Gigabit ports, along with stackability.
The key features of OmniSwitch 6XXX are:
• ELEMENT - One Standalone HAWK Unit (1 or 2 Intel Devices)
• Module - Insertable modules (Gigabit copper, fiber, or stackable)
• SLOT - Software numbering of an element
• Virtual Chassis - a stack of Hawk units (max stack =8)
• GARP - Generic Attributes Registration Protocol - A generalized protocol, defined in IEEE802.1p, for
signaling between workstations and the network.
• GMRP - GARP Multicast Registration Protocol - a version of GARP, which allows devices to request
membership in a specific multicast group. Part of the IEEE802.1Q/P, cited by Alcatel Enterprise QOS
requirements.
• GVRP - GARP VLAN Registration Protocol - a version of GARP, which allows devices to request
membership in a specific virtual LAN.
• IGMP - Internet Group Management Protocol, Version 2. The Hawk “snoops” this protocol to deter-
mine which ports should receive copies of multicast packets.
• IP Multicast - data packets sent from an IP host and intended for reception by a number of IP destina-
tion hosts. IP multicast frames have a Class D address in the 224.0.0.0 to 224.255.255.255 range. Each
address refers to an individual “broadcast stream” rather than a destination host. IP multicast was origi-
nally implemented using Ethernet multicast MAC addresses and was received by all hosts on the LAN.
• SFP - Small Form Factor Pluggable - Small form factor Fiber Gigabit connectors.
• Group Mobility - Alcatel Proprietary Protocol based VLAN
• Spanning Tree- Both 802.1D and 802.1W
• QOS
• Routing- Local, Static, RIP (2) and OSPF
• Link Aggregation
• 802.1Q
• Authenticated VLANs
• UDP/Bootp Relay
• Redundant Management when stacked
OmniSwitch Troubleshooting Guide September 2005
page -43
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
Hardware Architectural Overview
OS6600 uses off the shelf Intel ASIC. Intel IXE2424 Switching ASIC is used to implement the required
functionality.
The key features of Intel IXE2424 are:
• Provides 24 10/100 FE ports and 4 GE ports.
• L2 and L3 switching
• Integrated FE and GE Macs
• L2/L3/L4 Prioritization16K MAC, 16K IP, 8K IPX, 4K VLAN Tables, IEEE 802.1s
• Multiple Spanning Tree IEEE 802.1v VLAN Classification by Protocol
24
10/100
10/100
PHYs
4 MB
Packet
Storage
Packet
Data
Path
4 X
Gigabit
Gig
PHYs
Queuing
Engine
CPU
Interface
Switching/Routi
ng Engine
PCI Complaint CPU
Interface
External SSRAM for
Address Tables
Intel ASIC IXE 2424 Block Diagram
page -44
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
Packet Memory
Address
Memory
IXE 2424
MDIO
GM11/10 Bit
Interface
External Interfaces to IXE 2424
OmniSwitch Troubleshooting Guide September 2005
page -45
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
Layer 2 Forwarding
• Packets enter the IXE2424 through the SMII & GMII/TBI pins from external PHY devices. First, the
MAC associated with the port the packet was received from processes the packet. The MAC checks the
CRC to see if the packet is valid and also updates appropriate receive packet port statistics.
• In parallel, two things happen next.
• The entire packet is stored in external packet memory and
• The 64 byte packet header is sent to the address resolution logic (ASIC)
• External packet memory contains dedicated memory space for each port. The system processor (via the
Memory Start and Depth Address Registers) configures this address space at power up.
• The packet headers are queued, on a per port basis, before being placed in the processing pipeline. The
headers are examined for errors (i.e. length field, legal MAC address etc). The header is then examined
for
• Presence of prepend word
• Ethernet frame format
• Protocol carried
• Presence of VLAN tag
The Next step is address resolution. Note some packets like BPDU, GARP, LACP etc, bypass address
resolution and are passed to CPU for further processing.
Address Resolution Protocol
The IXE2424 switches packets based on flow. For Layer 2 packets, the IXE2424 identifies the flow using
802.1Q VLAN tag and Source and Destination Ethernet addresses. For IP addresses, the flow can be iden-
tified by the Source and Destination IP addresses, the protocol carried by the packet, and Source and
Destination Socket numbers. The flow entries are created in the software using the Address Resolution
Task provided by Intel’s driver software.
The Address Resolution task registers with the Notification Manager to be notified when an unresolved
entry is received. The Notification Manager function running in the Interrupt Handler context wakes up
this task upon receiving an unresolved entry. The Address Resolution task contains functions for learning
addresses. The Address Resolution task checks the unresolved queues for new entries and uses the CAM
interface to add new addresses to the table. An entry is created for the address with default settings. The
task sends an event through the Event Manager indicating that a new entry has been created. The Configu-
ration Management task waits on this event and with an occurrence, processes the newly added address,
and applies any special properties configured for that address.
page -46
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
Address Learning
Address Learning in the IXE2424 is performed primarily in the software. The hardware provides a CAM
interface to facilitate fast learning of addresses.
On power-up, the switch does not know which addresses are associated with which ports. So, when the
switch receives the first packet, the source address lookup fails. This packet is considered source and
destination address unresolved and is sent to the CPU for address learning. The CPU is interrupted indicat-
ing that an unknown address has been received.
The Address Resolution task that is provided as a part of the driver registers for such an event with the
event manager. This task wakes up, processes the unknown address and creates an entry for the address.
An event is then sent through the Event Manager and wakes up the Configuration Management task. The
configuration task goes through the list of rules and if the address matches any of the configured rules,
those rules are applied to the new learned address.
For destination unresolved packets, the packet is broadcast on all other ports within the VLAN and a desti-
nation unresolved entry is sent to the CPU. The destination (if one exists) receives the packet and responds
back. The driver then learns the destination. All future packets are then forwarded in hardware with no
software intervention.
If the source address was unknown, an unresolved entry is sent to the CPU and depending on whether or
not the destination was resolved or unresolved (or was a broadcast), the packet is sent to the destination
port (if the packet was resolved) or flooded within the VLAN (if the destination was unknown or the
packet was a broadcast packet). The IXE2424 provides the option to turn off such forwarding and the
driver provides an API to do this.
Location of Address Tables
The IXE2424 has two modes of operation - Normal Mode and Low Cost Layer 2 Mode. The locations of
address tables are different for the two modes. In Normal Mode, Layer 4 Record Entries and 12 Last
Address Record Entries are stored on-chip. The rest of the data structures are stored in off-chip address
memory. In Low Cost Layer 2 Mode of operation, there is no external address memory used. All data
structures are contained on-chip.
For the Hawk, we will use the Normal mode with External Address memory.
OmniSwitch Troubleshooting Guide September 2005
page -47
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
Address Look-up Methodology
Source and Destination Addresses are searched in parallel and then a sync process occurs to ensure both
are completed. The IXE2424 uses a fast method of organizing and searching the address records to meet
wire speed performance requirements. Record Entries (see Layer 2 Data Structures section below) contain
the addresses. A proprietary binary search algorithm is employed to look for these addresses; no hashing
algorithm is used. Records are organized into 1366 sections of 12 each (supporting a maximum of 16K
records) for L2. A similar organization exists for IP records (64K max records) and IPX (8K max entries).
Note that in Layer 2 only mode, all 40K addresses can be MAC addresses.
For the Hawk platform we will only use the ASIC in mode 4, which is Layer 3 switching with routing and
Layer 4 classification. Phase 1 will be L3 switching with L4 classification.
A binary search (on-chip) is performed among the Last Address (LA) of every section to find section
where the address should belong. A discriminated search is then performed with 10 bits to locate the
Record Entry where the address will fall if it is present. An external search for the record entry is then
performed. If the Record Entry matches with the address for which the search is performed, the rules and
protocol entries are also retrieved from external RAM.
L2 Data Structures
The layer 2 data structures for OS6600 are:
• 1-Record Entry
• Contains exact address used for match when searching tables
• MAC Address
• VLAN Tag ID (VID)
• 2-Rules Entry
• Contains information on which port the address resides on
• Device Number (IXE2424 number in cascaded systems)
• Port Number (which port this address resides on)
• Pointer to Protocol Specific Information
• Pointer to Destination Swap Information
page -48
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
3-Protocol Entry
• Used to allow different rules to be applied for different protocols associated with same address. Proto-
col Offset Register is used to identify which protocols will be used in the system. Up to 18 Layer 2
protocols are supported. There is a separate protocol entry for each protocol defined in the Protocol
Offset Register
• Priority level of the packet for queuing
• Filter (6 bits), Mirror (5 bits), Priority (5 bits), TOS (6 bits) indices for flow-based rules. Each address
that is to be used in a flow definition is assigned a unique index for the appropriate rule (i.e. Filter,
Mirror, priority or TOS).
• TOS marking rules
• Global destination/source priority rules (i.e. all packets with this destination address get this priority).
• Global destination/source filter rules (i.e. filter all packets with this source address)
• Global destination/source mirror rule (i.e. mirror all packets with this source address)
• Pointer to NetID
• 4-NetID Entry
• Contains transmit enables, prepend information and address based VLAN information.
OmniSwitch Troubleshooting Guide September 2005
page -49
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
Layer 3 Forwarding
Yes
Does the
Apply address VLAN for
Untagged packet
address exist
Yes
No
L3-
Send the packet to CPU for
address Learning
Is Routed
Broadcast the packet to all the
ports in the VLAN
Is the dest
and receive
Apply Filter,
Mirror, Priority,
Yes
N
Find Outgoing Tag and Port’s
802.1Q status
Apply Filter, Mirror, Priority,
QOS and WRED Rules
Is the dest Port
member of
Find outgoing Port’s 802.1Q
Drop the
Yes
Modify and Send the Packet to the Destination Port
page -50
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
VLANs
The IXE2424 supports VLANs based on:
• Ports. This is accomplished using Port Net ID Entry described below.
• 802.1Q Tags. This tag is included in the packet.
• Protocols. This is accomplished using the Protocol to VID Lookup Table described below.
• Addresses. This is accomplished by using the AVID field in NetId (L2, IP or IPX), if Address-based
VLAN feature is enabled.
The VLAN Tag ID (VID) in the Record entry is determined one of two ways
• For a tagged packet VID is the VLAN ID in the tag.
• For an untagged packet, VID is the default VLAN ID associated with the protocol the packet belongs
to. See Protocol Based VLANs description below.
Port Based VLANs
This is the default means of creating VLANs when no other type VLANs (802.1Q for example) has been
programmed. Port Net ID Entry is fetched based on the receive port number. This entry determines the
ports (including CPU) on which the packet received on that port can be transmitted.
Protocol Based VLANs
Can be configured on the IXE2424 by having different protocols point to different VLAN ID Entries
where a VLAN tag is programmed per protocol per port. The IXE2424 supports 19 different Protocol
Based Entries (IP, IPX, ARP etc) including 9 programmable protocols. Protocol to VID Lookup Table
assigns the VID on a per port, per protocol basis. Protocol-based VLAN control bit has to be set for this
feature to work.
Address Based VLANs
Layer 2, IP & IPX NetID entries has AVID (address based vid) field, which is used for untagged packets
as the 802.1Q VLAN ID for all further tag based processing, when Address-based VLAN feature is
enabled.
OmniSwitch Troubleshooting Guide September 2005
page -51
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
Tag Net ID Entry
• Contains related information like tagged set and member set. A 4x32 bit entry is present for every
possible VLAN (4096 supported).
• VLAN Tag Valid. Indicates if this VLAN tag has been configured by the CPU. If not, all packets with
this tag are dropped.
• Ports on which a packet with this Tag can go out on.
• VLAN Statistics Index. IXE2424 can collect statistics on up to 15 VLANs, identified by this index.
• IP Statistics Index. The IXE2424 can collect statistics on up to 256 IP Routed packets, identified by
this index.
• Tagged Set Port indicates which ports have nodes attached that can accept tagged packets on this
VLAN; packets are forwarded untagged to ports that cannot accept the tagged packets.
• Multicast Forward indicates which ports are disabled from transmitting unregistered multicast packets
on this VLAN. If the bit is set for a particular port, unregistered multicast packets are not transmitted
on that port.
• Priority, Bandwidth Management and QOS
Priority
• Each port on the IXE2424 has four output/transmit queues that store pointers to packets to be transmit-
ted. Each queue corresponds to one distinct priority level. Packets in higher priority queues are serviced
before packets in lower priority queues. These transmit queues support weighted fair queuing as well as
strict priority queuing algorithms.
• The IXE2424 supports three methods of assigning device priority to a packet: 802.1p Priority, Rules-
based Priority and QoS flow.
802.1p Priority
The incoming packet may have a priority associated with its 802.1Q Tag. 802.1p priority specifies eight
levels of priority. This priority level is mapped to one of the four device priority levels (per port) using the
Priority Map Register. Note this Priority Map Register applies to all ports on the IXE2424. If the incom-
ing packet is untagged, it is assigned a default 802.1p priority level of zero. However, the priority regener-
ation feature may be used to change this priority level on a per-port basis using the Port Regenerate Tag
Priority Level Entry Register.
page -52
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6624/6648 Architecture
Rules-Based Priority
• Several types of priority rules are supported. Each rule is associated with a specific device priority. If a
packet satisfies a certain priority rule, it is assigned the device priority corresponding to that rule.
• Global Priority Rules enable assignment of specific device priority to all packets from a specific source
address (global source priority) or all packets meant for a specific destination address (global destina-
tion priority). This is enabled through the Rules Entry data structure.
• Flow-based Priority Rules enable assignment of priorities by setting up priority flows. A flow refers to
packet transmission between a specific source and a specific destination address. When a packet is
detected to belong to a priority flow, it may be assigned a device priority as a set up for the flow. This
is enabled through the Rules Entry data structure.
• Protocol-based Priority is enabled by Flow-Based and Global Priority. It allows the user to assign
different device priority for packets that satisfy the same flow rules or global priority rules, but corre-
spond to different protocols.
QOS Flow
The QoS-specified device priority may override the device priority already assigned to a packet through
the VLAN tag, or through the global or flow-based priority. The decision to override previously assigned
device priority in favor of QoS-specified device priority is based on the value of bit 30 of SIC Control 0
Register. The user configures this bit.
Bandwidth Management and QoS
• The IXE2424 provides Bandwidth Management at two levels. First, the device manages bandwidth
between different output queues (that store pointers to the packet entries for transmission) at each port
through a priority queuing scheme. Credit based and strict priority are supported. The choice of one of
these two algorithms is configured on a per port basis using the Weighted Fair Queuing Port Address
Control Registers.
• The second level of Bandwidth Management is at the per-output queue level, through QoS rules for
packet flows, setup by the user. This provides bandwidth management on per queue and per flow basis
and is termed QoS bandwidth management. The corresponding flows are termed QoS flows. A QoS
flow essentially specifies a traffic-policing rule and allows users to limit bandwidth assigned for the
specific flow. QoS flows may be specified in terms of flow between two specific addresses, A and B;
flow from a specific address to any destination address; and flow to a specific destination address from
any source address.
• A QoS flow specifies a data limit value, time interval over which the data limit is to be enforced, and a
priority level (which determines the transmit queue number) for the flow. The IXE2424 device keeps
track of the amount of data that has been transmitted within the user-specified time intervals for each
QoS flow. If a packet causes a specific QoS flow to exceed its data allocation, it is dropped. Multiple
QoS flows may be mapped to the same transmit queue and still be guaranteed the required bandwidth
for that flow - the bandwidth management feature takes care of guaranteeing the bandwidth for the
queue (by not allowing other queues to take away unauthorized bandwidth) and the QoS feature guar-
antees bandwidth for all flows mapped to the same queue (by not allowing any of the flows to exceed
their allocated data rate). The device level Bandwidth Management feature is responsible for guaran-
teeing the bandwidth for an output queue (by not allowing other queues to take away unauthorized
bandwidth) and the QoS feature guarantees the bandwidth for all flows mapped to the same queue (by
not allowing other flows to exceed their allocated data rate). By combining these two types of band-
width management, users can efficiently manage bandwidth for different types of traffic with the
IXE2424 device.
OmniSwitch Troubleshooting Guide September 2005
page -53
Download from Www.Somanuals.com. All Manuals Search And Download.
CMM Functionality for OS6600
CMM Functionality for OS6600
The overall software architecture of Falcon is retained for Hawk. The user will perceive the system as a
virtual chassis; where one element is elected as the primary CMM, another as the secondary CMM and the
rest of the elements as NI. The two elements that are elected primary CMM and secondary CMM are also
NI. This choice was directed by finding a solution to manage the entire stack with a single IP address.
A Hawk used as standalone switch/router includes the equivalent of the CMM application as well as the
NI applications. When several Hawks are connected together via the stacking link, two of the Hawks
contains CMM and NI applications running on the same processor, and the rest contain a limited Chassis
Supervision and NI applications.
CMM (primary)
NI (slot 1)
NI (slot 2)
NI (slot 4)
NI (slot 3)
CMM (idle)
CMM (secondary)
CMM (idle)
page -54
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
CMM Functionality for OS6600
The chassis like, or V-Chassis, strategy allows the system to keep the same management interface. Since
on Falcon/Eagle, the management uses the notion of slot, this notion of slot is retained for Hawk. Since
there is no chassis, we need to provide a means by which a slot number is assigned to an element. The
current strategy is to have the user assigning a slot number, via a push button on the front panel, located
below the LCD display. The default slot number is one. This mechanism provides several advantages. It
removes the risk that from one reboot to another a dynamic allocation protocol might under certain
circumstances assign a different slot number. The second advantage is that even if the user removes an
element (slot) or adds one, the current configuration will still be applicable. There is no need to have
successive numbers in a stack. Eight (8) is the maximum number of slots allowed in a single stack.
The V-Chassis provides to the user the same interface and the same set of commands to configure the
system. The user configures a port; adds a port in a VLAN, etc, by providing both the port number and the
slot number. Chassis Supervision, NI Prober and Supervision and IPC are the main applications that are
impacted by the virtual chassis concept. They will both rely on the first application to have information
allowing them to perform their services correctly (i.e. NI present, NI UP, NI down).
The V-chassis imposes some constraints on Chassis Supervision. Chassis Supervision does not run the
Falcon election protocol, i.e. Hello Protocol, to define the mode (primary or secondary). Chassis Supervi-
sion receives the mode from Stack Manager. This implies that the Hello Protocol is not activated on both
the primary and secondary CMM, because the Stack Manager monitors the two CMMs. In Hawk three
modes are defined for Chassis Supervision. The new mode is idle. In the idle mode allows the system to
have Chassis Supervision available on all elements.
In primary mode, Chassis Supervision behaves as defined in Falcon with the following restrictions:
• CSM (Chassis State Machine) does not activate the Hello Protocol.
• HSM (Hardware Service Manager) does not need to control the available power when a NI is declared
present. On a real chassis (Falcon or Eagle), when Chassis Supervision learns the presence of a new
NI, it first computes whether or not there is enough power to switch on the new NI. This phase must be
bypassed on Hawk since each element has its own power supply.
• HSM needs to communicate to all elements within the stack a new temperature threshold, when it
receives the new configuration.
• Prober does not need to monitor the presence of either the NI or CMM boards. The service is now
available via Stack Manager.
• CVM (Chassis Version Manager) when synchronizing the primary Flash with the secondary Flash
needs to extend the service to all the elements present in the stack, ensuring that all elements have the
same content on the flash.
• When a new element is inserted in the stack, CVM must control that the flash content of this new
element is synchronized with the content of the primary flash.
• There is no need to have a synchronization of the MAC addresses.
• In secondary mode, Chassis Supervision, Chassis Supervision behaves as defined in Falcon with the
following restrictions:
• Prober does not need to monitor the presence of either the NI or CMM boards. The service is now
available via Stack Manager.
• Prober needs to monitor the temperature and report a temperature rising over a defined warning thresh-
old to HSM.
• When HSM receives a message from prober indicating that the temperature has risen over the defined
shutoff threshold, it must send a trap and shutdown the local unit.
OmniSwitch Troubleshooting Guide September 2005
page -55
Download from Www.Somanuals.com. All Manuals Search And Download.
CMM Functionality for OS6600
• In idle mode the role of Chassis Supervision is limited to monitoring the temperature, power supply,
fan(s), handling of flash synchronization and takeover. The following services are provided when
running in idle mode:
• Prober needs to monitor the temperature and report a temperature rising over a defined warning thresh-
old to HSM.
• When HSM receives a message from prober indicating that the temperature has risen over the defined
shutoff threshold, it must send a trap and shutdown the local unit.
• CVM must listen to flash synchronization coming from CVM on the primary.
• Chassis Supervision does not implement the Hello Protocol as defined in Falcon/Eagle. It receives noti-
fication from Stack Manager to change to a new mode. The following figure illustrates the different
possible transitions.
Stack manager
Primary
notification
Secondary
or user initiated
reset
reset
Stack manager
notification
Stack manager
notification
Idle
• When running in idle mode and upon reception of a notification of Stack Manager indicating the new
state, Chassis Supervision shutdowns the daughter tasks and spawns them according to the new mode.
page -56
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
CMM Functionality for OS6600
The process of multiple CMMs is composed of following steps:
• Bootup
• Role election
• Lowest slot number is elected as Primary
• Following number is elected as secondary
• Redundancy
• Failure of primary
• Secondary takeover
• Lowest idle number become secondary
• Failure of secondary
• Lowest idle number become new secondary
• Failure of both
• Election of a new primary and secondary
OmniSwitch Troubleshooting Guide September 2005
page -57
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6600 IPC Communication
OS6600 IPC Communication
IPC software interface is unchanged. IPC provides the following services:
• NI-NI communication
• CMM-NI communication
• CMM is the primary or active
• CMM-CMM communication
• Each element in a stack is addressable from its CMM perspective. Different Types of Sockets are:
• Connection oriented socket
• Connectionless socket
• Multicast socket
• IPC is transported as a layer 2 protocol over Ethernet frame
• Provides Segmentation and Reassembly
• Fragment packet bigger than 1400 bytes
• Provides reliability
• Interface with Stack Manager to obtain MAC address and outgoing port number
• Use special MAC to identify IPC packet
• For all slots a Special MAC is used. Example: slot 7 uses 00:00:77:77:77:77, slot 8 uses
00:00:88:88:88:88
The following diagram can illustrate IPC connection between different slots:
CAM Entry on device 5
Slot 5
Port=30
Dev=
00:00:11:11:11:1
VID 1
Slot 4
Slot 3
Slot 2
Slot 1
CAM entry on device 1
Port=30
Dev=
00:00:44:44:44:44
00:00:11:11:11:
VID 1
00:00:44:44:44:
0xABCD
IPC Frame sent from Slot 1 to Slot 4
page -58
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6600 BOOT Sequence
OS6600 BOOT Sequence
• Different from Falcon/Eagle
• No NI code to download
• Each element is independent from the other
• For instance it is possible to have a primary which has not the lowest slot number
The following figures illustrate the bootup process:
Load
Base
Stack
Manage
IPC
Librarie
Wait for Stack
Manager
Chassis
Supervisio
Wait for stack port
Configuration
From ESM Driver
NI
Stack
Manager
Supervisio
• Load the Base Code
• Load the Stack Manager Library
• Start IPC
• Load all the libraries
• Start Chassis Supervision
• Wait for Stack Manager
• Get the topology of the stacks
OmniSwitch Troubleshooting Guide September 2005
page -59
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6600 BOOT Sequence
• Get the Role of the Stack-Primary, Secondary or Idle
• Start NI supervision and Prober
• Start Stack Manager
• Get the stack port Configuration from the ESM Driver
IXE 2424
driver
NI
Chassis
Supervisio
Supervisio
Chassis
supervision
Queue
Stack
Manager
Compute
stack
ESM
Stack port configuration
• NI Supervision performs the following Tasks:
• Load and Start the IXE2424 driver
• Start the Queue Dispatcher
• Start Stack Manager to compute the stack topology and the role of the chassis from chassis supervision
• Start ESM driver by getting the information from Stack Manager
• Chassis Supervision performs the following tasks:
• Start all the daughter tasks when powered on, which include
• CMM applications
• Start the ESM Driver, which includes:
page -60
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6600 BOOT Sequence
Chassis
Supervisio
Daughter
Tasks
CMM
applicatio
CMM
applicatio
NI powered on
ESM
Driver
Start message
NI
NI
applicat
NI
applicat
NI
applicati
NI
applicatio
Supervisio
• NI supervision and Prober Task. NI Supervision task in turn starts the NI applications.
OmniSwitch Troubleshooting Guide September 2005
page -61
Download from Www.Somanuals.com. All Manuals Search And Download.
OS6600 BOOT Sequence
page -62
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
B Debug Commands
This chapter documents the following Command Line Interface (CLI) debug commands. Blue text indi-
cates that the text is hypertext-linked to additional documentation for that command.
802.1Q Debug Commands
DVMRP Debug Commands
debug ip dvmrp graft
debug ip dvmrp group
debug ip dvmrp nbr vlan
debug ip dvmrp prune recv
debug ip dvmrp rib holdq ageq
debug ip dvmrp route valid hold vlan
IP Debug Commands
debug ip packet (configures IP debug parameters)
debug ip set
debug ip
debug ip packet (displays IP debug configuration parameters)
debug ip mask
DHCP Relay Debug
Commands
debug ip helper packet size
Multicast Routing Debug
Commands
OSPF Debug Commands
PIM-SM Debug Commands
RIP Debug Commands
Trap Debug Commands
debug trap trace
debug trap reset
debug trap interface
debug trap generate
debug trap data
OmniSwitch Troubleshooting Guide September 2005
page -1
Download from Www.Somanuals.com. All Manuals Search And Download.
SNMP Debug Commands
Session Debug Commands
debug snmp trace
debug snmp reset
debug snmp interface
debug snmp data
debug session trace
debug session reset
debug session interface
debug session data
Hardware Slot Debug
Commands
debug interfaces set mdix
debug interfaces set automdix
debug interfaces set linkled
debug interfaces set linkled activity
IPC Debug Commands
debug ipc active sockets appid
Fabric ASIC Debug
Commands
page -2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Debug Commands
debug slb
debug slb adminstatus
debug slb createcluster
debug slb deletecluster
debug slb clusteradminstatus
debug slb clusterdistribution
debug slb clusterpingperiod
debug slb clusterpingtimeout
debug slb clusterpingretries
debug slb clusterstickytime
debug slb server
debug slb removeserver
debug slb dumpcluster
debug slb dumpclusters
debug slb dumpserver
debug slb dumpservers
debug slb dumpni
debug slb dumpvlan
debug slb dumpmisc
debug slb discoveryperiod
debug slb discoverytimeout
debug slb discoveryretries
debug slb statperiod
debug slb deadlinewindow
debug slb link
debug slb resetcmm
debug slb resetni
debug slb cmmtrace
debug slb nitrace
debug slb nidebug
debug slb flags
debug slb traps
debug slb simservers
debug slb serverarp
debug slb packetloss
debug slb kill
debug slb ni
debug slb snapshot
debug slb certify
debug slb takeover
HTTP Debug Commands
OmniSwitch Troubleshooting Guide September 2005
page -3
Download from Www.Somanuals.com. All Manuals Search And Download.
HRE Debug Commands
debug hre ipx flow
debug hre ipms flow
debug hre ip flow
debug hre clear ipx
debug hre clear ip
debug hre cache verbose
debug hre cache
Health Debug Commands
debug health temperature cpu
debug health temperature cmm
debug health status
debug health txrx
GMAP Debug Commands
Console Debug Commands
Commands
CLI Debug Commands
debug cli mip-response
CLI Shell Debug Commands
AMAP Debug Commands
Chassis Debug Commands
debug chassis show state trace
Bridging Debug Commands
debug bridge hash-bitmask sa
debug bridge hash-bitmask da
page -4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
VLAN Debug Commands
debug vlan rule memory
debug vlan database
Port Manager (PM) Debug
Commands
debug pm object
debug pm mibs
debug pm eventlist
debug pm bindings
debug pm index
AAA Debug Commands
Port Debug Commands
QoS Debug Commands
IPX Debug Commands
debug aaa
debug ipx info
debug ipx info rip
debug ipx info host
debug ipx trace
debug ipx vlan
Systrace Debug Commands
Post Mortem Dump (PMD)
Debug Commands
debug remove pmd
debug pmd remove
debug pmd show
debug dump pmd
debug pmd ni
debug show pmd
Memory Monitoring Debug
Commands
Ktrace Debug Commands
Ed Debug Commands
Set Debug Commands
Debug Show Commands
IPv6 Debug Commands
debug ed
debug set
debug show
debug ipv6 trace
OmniSwitch Troubleshooting Guide September 2005
page -5
Download from Www.Somanuals.com. All Manuals Search And Download.
debug 802.1q
Retrieves debugging messages for the tagged port selected.
debug 802.1q {slot/port | aggregate_id}
Syntax Definitions
slot
The slot number to configure 802.1Q tagging.
port
The port number to configure 802.1Q tagging.
aggregate_id
The aggregate link number to configure 802.1Q tagging.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
Retrieves debugging messages for the tagged port selected.
Examples
-> debug 802.1q 5
Aggregate Status =
aggregate up
-> debug 802.1q 3/1
Slot Status =
Port Status =
slot up
port up
GENERAL INFO ESM: USER PORT 1-12 = CORONADO PORT 0-11
GENERAL INFO ESM: USER PORT 13-24 = CORONADO PORT 16-27
GENERAL INFO GSM: USER PORT 1 = CORONADO PORT 12
GENERAL INFO GSM: USER PORT 2 = CORONADO PORT 28
HARDWARE INFO for slot = 3 and port = 1:
At reg_addr = 660012c, Ingress tag-untag:= 1:
At reg_addr = 6a00010, Eg tag-untag: = 1:
At reg_addr = 6601000,for protocol = 0,ing default vlan: = 1
At reg_addr = 6601080,for protocol = 1,ing default vlan: = 1
At reg_addr = 6601100,for protocol = 2,ing default vlan: = 1
At reg_addr = 6601180,for protocol = 3,ing default vlan: = 1
At reg_addr = 6601200,for protocol = 4,ing default vlan: = 1
At reg_addr = 6601280,for protocol = 5,ing default vlan: = 1
At reg_addr = 6601300,for protocol = 6,ing default vlan: = 1
At reg_addr = 6a70000, egress default vlan: = 1
At reg_addr = 6600118, protocol cam on/off: = 18 :
At reg_addr = 660011c, trusted/untrusted: = fff0fe6
At reg_addr = 6600130, secure/unsecure: = 18
At reg_addr = 6608020, for vlan = 8,spanning tree vector: = 1
At reg_addr = 6a00014, Eg force tag internal: = 0:
page -6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
output definitions
Aggregate/Slot Status
Port Status
Whether the slot or aggregate link is actively running.
Whether the port is actively running.
General Info
Provides general information on the modules in the chassis, including
module type, number of ports, and ASIC.
Hardware Info
Lists the various debug messages for the selected slot and port.
Release History
Release 5.1; command was introduced.
Related Commands
N/A
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -7
Download from Www.Somanuals.com. All Manuals Search And Download.
ip dvmrp debug-level
Defines the level of debugging for DVMRP protocol on the switch.
ip dvmrp debug-level level
Syntax Definitions
level
Specifies the DVMRP debug level (0–255). Higher debug-levels will
include all messages that correspond to a lower value. For example, a
debug level of 2 will display all messages for level 1 and level 2. As a
rule of thumb, higher levels will display more detailed messages; lower
levels will display more basic messages.
Defaults
parameter
default
level
1
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
When the debug level is set to 0, DVMRP debug logging is turned off.
Examples
-> ip dvmrp debug-level 2
Release History
Release 5.1; command was introduced.
Related Commands
Enables or disables DVMRP debugging for a specified message
type, or for all message types.
Displays the current level of debugging for DVMRP protocol on the
switch, as well as the current DVMRP debugging status for all mes-
sages types.
MIB Objects
ALADVMRPDEBUGCONFIG
alaDvmrpDebugLevel
page -8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
ip dvmrp debug-type
Enables or disables DVMRP debugging for a specified message type, or for all message types.
Note. Debugging for a specified message type will only be enabled if its debug level is a value greater
than zero (i.e., 1–255). For information on specifying the debug level, refer to the
ip dvmrp debug-level command.
ip dvmrp debug-type message_type
no ip dvmrp debug-type message_type
Syntax Definitions
message_type
Enables or disables DVMRP debugging for the specified item. Select
from the list below. You may enter multiple message types in any order.
For example, ip dvmrp debug-type time flash init.
supported message types descriptions
all
Enables or disables DVMRP debugging for all items listed below. The
syntax all can be used to easily turn debugging for all message types on
or off.
error
flash
graft
igmp
Enables or disables debugging for DVMRP Error messages.
Enables or disables debugging for DVMRP Flash processing.
Enables or disables debugging for DVMRP Graft processing.
Enables or disables debugging for DVMRP Internet Group Management
Protocol (IGMP) packet processing.
ipmrm
Enables or disables debugging for DVMRP IP Multicast Routing Man-
ager (IPMRM) interaction.
init
Enables or disables debugging related to DVMRP initialization code.
mip
Enables or disables debugging for MIP (Management Internal Protocol)
processing. Includes CLI and SNMP.
misc
Enables or disables miscellaneous debugging of DVMRP.
Enables or disables debugging for DVMRP Neighbor processing.
Enables or disables debugging for DVMRP Probe processing.
Enables or disables debugging for DVMRP Prune processing.
Enables or disables debugging for DVMRP Route processing.
Enables or disables debugging for DVMRP Timer processing.
Enables or disables debugging for DVMRP Task Manager interaction.
nbr
probes
prunes
routes
time
tm
OmniSwitch Troubleshooting Guide September 2005
page -9
Download from Www.Somanuals.com. All Manuals Search And Download.
Defaults
parameter
default
message_type
error
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• Use the no form of the command to disable debugging for the specified item.
• Reminder: Debugging for a specified message type will only be enabled if its debug level is a value
greater than zero (i.e., 1–255). For information on specifying the debug level, refer to the
ip dvmrp debug-level command.
• The syntax all can be used to easily turn debugging for all message types on or off
(e.g., ip dvmrp debug-type all or no ip dvmrp debug-type all).
Examples
-> ip dvmrp debug-type all
-> ip dvmrp debug-type tm igmp flash
-> no ip dvmrp debug-type misc
-> no ip dvmrp debug-type all
Release History
Release 5.1; command was introduced.
Related Commands
Defines the level of debugging for DVMRP protocol on the switch.
Displays the current level of debugging for DVMRP protocol, as
well as the current DVMRP debugging status for all message types.
MIB Objects
ALADVMRPDEBUGCONFIG
alaDvmrpDebugAll
alaDvmrpDebugError
alaDvmrpDebugFlash
alaDvmrpDebugGrafts
alaDvmrpDebugIgmp
alaDvmrpDebugInit
alaDvmrpDebugIpmrm
alaDvmrpDebugMip
alaDvmrpDebugNbr
alaDvmrpDebugProbes
alaDvmrpDebugPrunes
alaDvmrpDebugRoutes
alaDvmrpDebugTime
alaDvmrpDebugTm
page -10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
show ip dvmrp debug
Displays the current level of debugging for DVMRP protocol on the switch, as well as the current
DVMRP debugging status for all messages types.
show ip dvmrp debug
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• The administrative debugging status for message types displayed in the table are determined by the
ip dvmrp debug-type command.
• To configure debug levels, refer to the ip dvmrp debug-level command.
Examples
-> show ip dvmrp debug
Debug Level = 1,
Error
Flash
Grafts
IGMP
IPMRM
Init
= on,
= off,
= off,
= off,
= off,
= off,
= off,
= off
MIP
Misc
Nbr
= on,
Probes
Prunes
Routes
Time
= off,
= off,
= on,
= off,
= off,
TM
output definitions
Debug Level
The current debug level value. For information on setting this parame-
error
Flash
The current debugging status for DVMRP Error messages. Options
include on or off.
The current debugging status for DVMRP Flash processing. Options
include on or off.
OmniSwitch Troubleshooting Guide September 2005
page -11
Download from Www.Somanuals.com. All Manuals Search And Download.
output definitions (continued)
Grafts
The current debugging status for DVMRP Graft processing. Options
include on or off.
IGMP
IPMRM
Init
The current debugging status for DVMRP Internet Group Management
Protocol (IGMP) packet processing. Options include on or off.
The current debugging status for DVMRP IP Multicast Routing Man-
ager (IPMRM) interaction. Options include on or off.
The current debugging status for DVMRP Initialization. Options
include on or off.
MIP
The current debugging status for DVMRP MIP (Management Internal
Protocol) processing. Includes CLI and SNMP. Options include
on or off.
Misc
The current status of miscellaneous DVMRP debugging. Options
include on or off.
Nbr
The current debugging status for DVMRP Neighbor processing.
Options include on or off.
Probes
Prunes
Routes
Time
TM
The current debugging status for DVMRP Probe processing. Options
include on or off.
The current debugging status for DVMRP Prune processing. Options
include on or off.
The current debugging status for DVMRP Route processing. Options
include on or off.
The current debugging status for DVMRP Timer processing. Options
include on or off.
The current debugging status for DVMRP Task Manager interaction.
Options include on or off.
Release History
Release 5.1; command was introduced.
Related Commands
Defines the level of debugging for DVMRP protocol on the switch.
Enables or disables DVMRP debugging for a specified message
type, or for all message types.
page -12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ip packet
Enables/disables/configures the IP packet debug feature. This command is generally used only when
working with a field engineer to debug a problem on the switch.
debug ip packet [start] [timeout seconds] [stop] [direction {in | out | all}] [format {header | text | all}]
[output {console | file filename}] [board {cmm | ni [1-16] | all | none} [ether-type {arp | ip | hex
[hex_number] | all}] [ip-address ip_address] [ip-address ip_address] [ip-pair [ip1] [ip2]] [protocol {tcp
| udp | icmp | igmp | num [integer] | all}] [show-broadcast {on | off}] show-multicast {on | off}]
Syntax Definitions
start
Starts an IP packet debug session.
timeout
Sets the duration of the debug session, in seconds. To specify a dura-
tion for the debug session, enter timeout, then enter the session length.
seconds
stop
The debug session length, in seconds.
Stops IP packet debug session.
direction
Specifies the type of the packets you want to debug. Specify in to debug
incoming packets; specify out to debug outgoing packets; specify all to
debug both incoming and outgoing packets.
format
output
Specifies the area of the packet you want to debug. Specify header to
debug the packets header; specify hex to debug the packet text; specify
all to debug the entire packet.
Specifies where you want the debug information to go. Specify console
to print the output to the screen; specify file to save the output to a log
file.
filename
The filename for the output file.
board
Specifies the slot (board) that you want to debug. Specify cmm to
debug CMM packets; specify ni, then enter the slot number of the NI to
debug a network interface card; specify all to debug packets for all
CMMs and NIs on the switch; specify none to clear the previous board
settings.
ether-type
Specifies a specific Ethernet packet type to debug. Specify arp to debug
ARP packets; specify ip to debug IP packets; specify hex and enter an
ethernet packet type in hex format (e.g., 800) to debug a specific ether-
net packet type; specify all to debug all Ethernet packet types.
ip-address
ip-pair
Specifies an IP address to debug. The debug output will only be for
packets received from this IP address. Enter ip-address, then enter the
IP address that you want to debug.
Use this option to match packets exchanged between two network
addresses. Enter ip-pair, then enter each IP address.
OmniSwitch Troubleshooting Guide September 2005
page -13
Download from Www.Somanuals.com. All Manuals Search And Download.
protocol
Specifies a protocol type to debug. Specify tcp to debug TCP packets;
specify udp to debug UPD packets; specify icmp to debug ICMP pack-
ets; specify igmp to debug IGMP packets; specify num to numerically
specify a protocol (e.g., 89); specify all to debug all protocol types.
show-broadcast
show-multicast
Specifies whether or not to display broadcast packets. Specify on to
display broadcast packets on the screen or in the log; specify off if you
do not want to display broadcast packets.
Specifies whether or not to display multicast packets. Specify on to
display multicast packets on the screen or in the log; specify off if you
do not want to display multicast packets.
Defaults
parameter
default
timeout
-1
in | out | all
all
header | text | all
console | file
header
console
all
cmm | ni | all | none
arp | ip | hex | all
all
tcp | udp | icmp | igmp | num | all all
on | off
on | off
on
on
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• If you use the basic command to start debug (debug ip packet start) the switch will use default param-
eters for all of the debug options. Once you configure one of the optional parameters, the switch will
use the new parameter(s) until changed.
• If you do not specify a timeout value, the session will continue until it is stopped.
• You must enter the start keyword to begin debugging.
Examples
-> debug ip packet start timeout 1
Release History
Release 5.1; command was introduced.
page -14
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Configures IP debug level. This command allows you to set the level
(amount) of information displayed.
OmniSwitch Troubleshooting Guide September 2005
page -15
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ip level
Configures the IP debug level. This command allows you to set the level (amount) of information
displayed. The lower the level, the more significant the event. For example, a level of 1 will display only
the most critical problems. A level of 99 would display all of the available information for the specified
debug type. It is best to use the default level of 1 unless instructed to increase the level by a field engineer.
If more information is needed to debug a problem, a higher level can be selected.
debug ip level level
Syntax Definitions
level
Debug level. Valid range is 0–255.
Defaults
parameter
default
level
1
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
set different levels for different configurations.
Examples
-> debug ip level 1
Release History
Release 5.1; command was introduced.
Related Commands
Enables/disables/configures the IP packet debug feature.
page -16
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ip packet default
Returns IP packet debug options to default values.
debug ip packet default
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
Examples
-> debug ip packet default
Release History
Release 5.1; command was introduced.
Related Commands
Configures IP packet debug.
OmniSwitch Troubleshooting Guide September 2005
page -17
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ip packet
Displays IP debug configuration parameters. This command is generally used only when working with a
field engineer to debug a problem on the switch.
debug ip packet
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
This command is used to display IP debug configuration parameters. To start IP debugging you must enter
the start keyword.
Examples
-> debug ip packet
packet dump
timeout in seconds
output device
board
off,
0,
console,
all,
ether-type
protocol
all,
all,
direction
mcast/bcast
format
in + out,
on,
header,
IP address filter
output definitions
packet dump
timeout in seconds
output device
ether-type
IP debug administrative status (on/off).
Duration of the debug session, in seconds. (0 = off).
Output device for debug information (e.g., file, console).
Ethernet packet type to debug (e.g., ARP, IP).
Protocol type to debug (e.g., TCP, UDP).
protocol
direction
Type of traffic to debug incoming (in) or outgoing (out).
Specifies whether or not to show broadcast/multicast packets.
Area of the packet to debug (e.g., header, text).
Interface to debug.
mcast/bcast
format
ip address filter
page -18
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Release History
Release 5.1; command was introduced.
Related Commands
Configures IP packet debug.
OmniSwitch Troubleshooting Guide September 2005
page -19
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ip mroute debug-level
Configures the Mutlicast Routing debug level.
debug ip mroute debug-level level
Syntax Definitions
level
Specifies the Mutlicast Routing debug level (0–255).
Defaults
parameter
default
level
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
Higher debug-levels will include all messages that correspond to a lower value. For example, a debug
level of 2 will display all messages for level 1 and level 2. As a rule of thumb, higher levels will display
more detailed messages; lower levels will display more basic messages.
Examples
-> debug ip mroute debug-level 10
Release History
Release 5.1; command was introduced.
Related Commands
Displays the current multicast routing debug levels and types.
page -20
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
ip mroute debug-type
Displays the current multicast routing debug levels and types.
ip mroute debug-type [tm | protos {on | off} | misc | mip {on | off} | ipms {on | off} | init | fib {on | off} |
error {on | off} | all | aging {on | off}]
no ip mroute debug-type [tm | protos {on | off} | misc | mip {on | off} | ipms {on | off} | init | fib {on |
off} | error {on | off} | all | aging {on | off}]
Syntax Definitions
debug level
The current debug level value.
protos
The current state of messages related to multicast routing protocols
(e.g., whether they are enabled or disabled on interfaces, which proto-
cols are going up or down, etc.).
mip
The current state of messages related to MIP (Management Internal
Protocol).
ipms
fib
The current state of messages related to IPMS interaction.
The current state of messages related to IPMRM FIB processing.
The current state of messages related to all error handling.
The current state of messages related to IPMRM FIB aging entries.
error
aging
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
Use the no form of the command to turn off a specific type of debug or all debug types.
Examples
-> debug ip mroute debug-type error
Release History
Release 5.1; command was introduced.
Related Commands
Configures the Mutlicast Routing debug level.
OmniSwitch Troubleshooting Guide September 2005
page -21
Download from Www.Somanuals.com. All Manuals Search And Download.
ip ospf debug-level
Configures OSPF debugging level. The level refers to the granularity of the information provided. Gener-
ally, the higher the number, the more specific the information.
ip ospf debug-level level
Syntax Definitions
level
The debugging level. The valid range 0–255.
Defaults
parameter
default
level
0
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
This command allows you to select the granularity at which you wish to view debugging information.
Currently, in OSPF, there are three levels available:
• 10–Only critical errors and warnings.
• 50–Most errors, warnings, and events.
• 99–All errors, warnings and events.
Examples
-> ip ospf debug-level 10
Release History
Release 5.1; command was introduced.
Related Commands
Configures type of OSPF functionality to debug.
Displays current OSPF debug level and types.
MIB Objects
ALAOSPFDEBUGCONFIG
alaOspfDebugLevel
page -22
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
ip ospf debug-type
Configures the type of OSPF functionality to debug.
ip ospf debug-type [error] [warning] [state] [recv] [send] [flood] [spf] [lsdb] [rdb] [age] [vlink]
[redist] [summary] [dbexch] [hello] [auth] [area] [intf] [mip] [info] [setup] [time] [tm] [all]
no ip ospf debug-type [error] [warning] [state] [recv] [send] [flood] [spf] [lsdb] [rdb] [age] [vlink]
[redist] [summary] [dbexch] [hello] [auth] [area] [intf] [mip] [info] [setup] [time] [tm] [all]
Syntax Definitions
error
Administratively enables/disables debugging error messages. Error
messages provide information of program faults.
warning
state
Administratively enables/disables debugging warning messages.
Administratively enables/disables debugging OSPF state messages.
State messages show the switch state in relation to its neighbors.
recv
Administratively enables/disables debugging messages for packets
received by OSPF.
send
Administratively enables/disables debugging messages for packets sent
by OSPF.
flood
spf
Administratively enables/disables debugging messages for the flooding
of Link State Advertisements (LSAs) in OSPF.
Administratively enables/disables debugging messages for OSPF’s
Shortest Path First (SPF) calculations.
lsdb
Administratively enables/disables debugging messages for OSPF’s Link
State Database (LSDB) related operations.
rdb
Administratively enables/disables debugging messages for OSPF’s rout-
ing database (RDB) related operations.
age
Administratively enables/disables debugging messages for OSPF’s
aging process of LSAs.
vlink
redist
summary
dbexch
hello
Administratively enables/disables debugging messages for OSPF’s
virtual links operations.
Administratively enables/disables debugging messages for OSPF’s
route redistribution process.
Administratively enables/disables debugging messages for all OSPF’s
summarizations.
Administratively enables/disables debugging messages for OSPF neigh-
bors’ database exchange.
Administratively enables/disables debugging messages for OSPF’s hello
handshaking process.
OmniSwitch Troubleshooting Guide September 2005
page -23
Download from Www.Somanuals.com. All Manuals Search And Download.
auth
area
intf
Administratively enables/disables debugging messages for OSPF’s
authentication process.
Administratively enables/disables debugging messages for OSPF’s area
events.
Administratively enables/disables debugging messages for OSPF’s
interface operations.
mip
info
setup
time
tm
Administratively enables/disables debugging messages for MIP process-
ing of OSPF specific commands.
Administratively enables/disables debugging messages for purpose to
provide OSPF information.
Administratively enables/disables debugging messages for OSPF’s
initialization setup.
Administratively enables/disables debugging messages for OSPF’s time
related events.
Administratively enables/disables debugging messages for DRC’s Task
Manager communication events.
all
Administratively enables/disables all debugging listed above for OSPF.
Defaults
parameter
default
error | warning | state | recv | error
send | flood | spf | lsdb | rdb |
age | vlink | redist | summary |
dbexch | hello| auth | area | intf
| mip | info | setup | time | tm |
all
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• The debug command allows you to enable debugging on various OSPF functions. These messages can
be highly detailed, or very general, depending upon the debug level set.
• Use the no form of the command to turn off the selected debugging type.
Examples
-> ip ospf debug-type all
Release History
Release 5.1; command was introduced.
page -24
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Configures OSPF debugging level.
Displays current OSPF debug level and types.
MIB Objects
ALAOSPFDEBUGCONFIG
alaOspfDebugError
alaOspfDebugWarning
alaOspfDebugState
alaOspfDebugRecv
alaOspfDebugSend
alaOspfDebugFlood
alaOspfDebugSPF
alaOspfDebugLsdb
alaOspfDebugRdb
alaOspfDebugAge
alaOspfDebugVlink
alaOspfDebugRedist
alaOspfDebugSummary
alaOspfDebugDbexch
alaOspfDebugHello
alaOspfDebugAuth
alaOspfDebugArea
alaOspfDebugIntf
alaOspfDebugMip
alaOspfDebugInfo
alaOspfDebugSetup
alaOspfDebugTime
alaOspfDebugTm
alaOspfDebugAll
OmniSwitch Troubleshooting Guide September 2005
page -25
Download from Www.Somanuals.com. All Manuals Search And Download.
show ip ospf debug
Displays current OSPF debug level and types.
show ip ospf debug
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• This command is used to display the debugging information currently enabled for the OSPF router.
• See the related commands sections below to modify the list.
Examples
-> show ip ospf debug
Debug Level
Types/Sections
error
warning
state
recv
send
flood
spf
lsdb
rdb
age
vlink
redist
summary
dbexch
hello
auth
= 0,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
= on,
area
intf
mip
info
setup
time
tm
page -26
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
output definitions
Debug Level
The granularity of the debug messages. This number will be 10, 50, or
99, where the lower number is least specific.
error
The error debug messages status. Error messages provide information
of program faults.
warning
state
The warning debug messages status. Debugging messages show router
operation calls.
The state debug messages status. State messages show the router state
in relation to its neighbors.
recv
The received OSPF packet debug messages status.
The status OSPF packet debug messages status.
The flood debug messages status.
send
flood
spf
The Shortest Path First (SPF) debug messages status.
The Link State Database (LSDB) debug messages status.
The Routing Database (RDB) debug messages status.
The aging debug messages status.
lsdb
rdb
age
vlink
redist
summary
The virtual link debug messages status.
The redistribution debug messages status.
The summary debug messages status. Summarization of routes can be
set for stubby areas and NSSAs.
dbexch
hello
auth
area
intf
The data base exchange debug messages status.
The hello debug messages status.
The authorization debug messages status.
The area related debug messages status.
The interface related debug messages status.
The MIP operations debug messages status.
The information debug messages status.
The setup debug messages status.
mip
info
setup
time
tm
The time debug messages status.
The DRC debug messages status.
Release History
Release 5.1; command was introduced.
Related Commands
Configures OSPF debugging level.
Configures type of OSPF traffic to debug.
OmniSwitch Troubleshooting Guide September 2005
page -27
Download from Www.Somanuals.com. All Manuals Search And Download.
MIB Objects
alaOspfDebugLevel
alaOspfDebugError
alaOspfDebugWarning
alaOspfDebugState
alaOspfDebugRecv
alaOspfDebugSend
alaOspfDebugFlood
alaOspfDebugSPF
alaOspfDebugLsdb
alaOspfDebugRdb
alaOspfDebugAge
alaOspfDebugVlink
alaOspfDebugRedist
alaOspfDebugSummary
alaOspfDebugDbexch
alaOspfDebugHello
alaOspfDebugAuth
alaOspfDebugArea
alaOspfDebugIntf
alaOspfDebugMip
alaOspfDebugInfo
alaOspfDebugSetup
alaOspfDebugTime
alaOspfDebugTm
alaOspfDebugAll
page -28
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
ip pimsm debug-level
Defines the level of PIM-SM debug messages that are generated.
ip pimsm debug-level level
Syntax Definitions
level
Specifies the PIM-SM debug level (0–255). Higher debug-levels will
include all messages that correspond to a lower value. For example, a
debug-level of 1 will display only those messages that are defined with
a level of 1; however, a debug level of 2 will display all messages of
level 1 and level 2, etc. Higher levels will display detailed messages;
lower levels will display basic messages.
Defaults
parameter
default
level
1
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
When the debug level is set to 0, PIM-SM debug logging is turned off.
Examples
-> ip pimsm debug-level 2
Release History
Release 5.1; command was introduced.
Related Commands
Configures the type(s) of PIM-SM debug messages to display.
Displays the current PIM-SM debug levels and types.
MIB Objects
ALAPIMSMDEBUGCONFIG
alaPimsmDebugLevel
OmniSwitch Troubleshooting Guide September 2005
page -29
Download from Www.Somanuals.com. All Manuals Search And Download.
ip pimsm debug-type
Configures the type(s) of PIM-SM debug messages to display.
ip pimsm debug-type message_list
no ip pimsm debug-type message_list
Syntax Definitions
message_list
Specifies the type(s) of PIM-SM messages to be debugged. Select
supported PIM-SM message types from the list below. You may enter
multiple message types in any order. For example, ip pimsm debug-
type time flash init.
supported message types descriptions
all
Enables or disables PIM-SM debugging for all items listed below. The
syntax all can be used to easily turn debugging for all message types on
or off.
assert
bootstrap
crp
Enables or disables debugging for Assert Metric messages.
Enables or disables debugging for Bootstrap Router (BSR) messages.
Enables or disables debugging for Candidate Rendezvous Point (C-RP)
messages.
error
hello
igmp
Enables or disables debugging for PIM-SM Error messages.
Enables or disables debugging for PIM-SM Hello messages.
Enables or disables debugging for Internet Group Management Protocol
(IGMP) messages.
ipmrm
Enables or disables debugging for messages exchanged with IP Multi-
cast Routing Manager (IPMRM).
init
Enables or disables debugging related to PIM-SM initialization code.
Enables or disables debugging related to Join/Prune.
joinprune
mip
Enables or disables debugging related to MIP (Management Internal
Protocol).
misc
nbr
route
spt
Enables or disables miscellaneous debugging of PIM-SM.
Enables or disables debugging for PIM-SM Neighbor processing.
Enables or disables debugging for PIM-SM Route processing.
Enables or disables debugging related to Shortest-Path Tree (SPT).
Enables or disables debugging for PIM-SM Timer processing.
Enables or disables debugging for PIM-SM Task Manager interaction.
time
tm
Defaults
N/A
page -30
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• The message-types specified in the command line will only be displayed if the debug level has been set
to a number greater than zero (i.e., 1–255). For information on specifying the debug level, refer to the
• The syntax all can be used to easily turn on/off all message types (e.g., ip pimsm debug-type all or
no ip pimsm debug-type all).
Examples
-> ip pimsm debug-type all
-> ip pimsm debug-type bootstrap assert
-> no ip pimsm debug-type all
Release History
Release 5.1; command was introduced.
Related Commands
Defines the level of PIM-SM messages that are generated.
Displays the current PIM-SM debug levels and types.
MIB Objects
ALAPIMSMDEBUGCONFIG
alaPimsmDebugAll
alaPimsmDebugAssert
alaPimsmDebugBootstrap
alaPimsmDebugCRP
alaPimsmDebugError
alaPimsmDebugHello
alaPimsmDebugIgmp
alaPimsmDebugInit
alaPimsmDebugIpmrm
alaPimsmDebugJoinPrune
alaPimsmDebugMip
alaPimsmDebugMisc
alaPimsmDebugNbr
alaPimsmDebugRoute
alaPimsmDebugSpt
alaPimsmDebugTime
alaPimsmDebugTm
OmniSwitch Troubleshooting Guide September 2005
page -31
Download from Www.Somanuals.com. All Manuals Search And Download.
show ip pimsm debug
Displays the current PIM-SM debug levels and types.
show ip pimsm debug
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
Examples
-> show ip pimsm debug
Debug Level = 1,
assert
bootstrap
crp
error
hello
igmp
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off,
= off
init
ipmrm
joinprune
mip
misc
nbr
route
spt
time
tm
output definitions
Debug Level
The current debug level value. For information on setting this parame-
assert
The current state of messages related to assert metric.
Options include on or off.
bootstrap
The current state of messages related to bootstrap.
Options include on or off.
page -32
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
output definitions (continued)
crp
The current state of messages related to Candidate Rendezvous Point
(C-RP). Options include on or off.
error
hello
igmp
init
The current state of messages related to all error handling.
Options include on or off.
The current state of messages related to hello messages.
Options include on or off.
The current state of messages related to Internet Group Management
Protocol (IGMP) packet processing. Options include on or off.
The current state of messages related to initialization code.
Options include on or off.
ipmrm
joinprune
mip
The current state of messages exchanged with IP Multicast Routing
Manager (IPMRM). Options include on or off.
The current state of messages related to Join/Prune.
Options include on or off.
The current state of messages related to MIP (Management Internal
Protocol). Options include on or off.
misc
The current status of miscellaneous message handling.
Options include on or off.
nbr
The current state of messages related to the neighbors.
Options include on or off.
route
The current state of messages related to routes.
Options include on or off.
spt
The current state of messages related to Shortest-Path Tree (SPT).
time
The current state of messages related to the time.
Options include on or off.
tm
The current state of messages related to the Task Manager.
Options include on or off.
Release History
Release 5.1; command was introduced.
Related Commands
Defines the level of PIM-SM debug messages that are generated.
Configures the type(s) of PIM-SM debug messages to display.
OmniSwitch Troubleshooting Guide September 2005
page -33
Download from Www.Somanuals.com. All Manuals Search And Download.
ip rip debug-type
Configures the type of RIP messages to debug. The debug feature on the switch is generally used only
under the direction of a field engineer. Use this command to configure the type of RIP debug warnings
(e.g., errors, warning) that will be logged.
ip rip debug-type [error] [warning] [recv] [send] [rdb] [age] [redist] [info] [setup] [time] [tm] [all]
no ip rip debug-type [error] [warning] [recv] [send] [rdb] [age] [redist] [info] [setup] [time] [tm] [all]
Syntax Definitions
error
warning
recv
send
rdb
Includes error conditions, failures, processing errors, etc.
Includes general warnings, non-fatal conditions.
Enables debugging in the receive flow path of the code.
Enables debugging in the send flow path of the code.
Debugs RIP database handling.
age
Debugs code handling database entry aging/timeouts.
Debugs redistribution code.
redist
info
Provides general information.
setup
time
all
Provides information during initialization.
Debugs timeout handler.
Enables all debug options.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• Use the no form of the command to delete a debug type.
• RIP must be enabled on the switch with the ip rip status CLI command before you can configure the
debug type.
• To configure more than one debug type, you must repeat the command for each type.
Examples
-> ip rip debug-type all
page -34
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Release History
Release 5.1; command was introduced.
Related Commands
Configures RIP debugging level.
Displays the current RIP debug levels and types.
MIB Objects
alaRipLogTable
alaRipDebugType
OmniSwitch Troubleshooting Guide September 2005
page -35
Download from Www.Somanuals.com. All Manuals Search And Download.
ip rip debug-level
Configures RIP debug level. You can set the level of information displayed using the ip rip debug level
command. The lower the level, the more significant the event. For example, a level of 1 will display only
the most critical problems. A level of 99 would display all of the available information for the specified
debug type. It is best to use the default level of 1 unless instructed to increase the level by a field engineer.
If more information is needed to debug a problem, a higher level can be selected.
ip rip debug-level level
Syntax Definitions
level
Debug level. Valid range is 0–255.
Defaults
parameter
default
level
1
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• RIP must be enabled on the switch with the ip rip status CLI command before you can configure the
debug level.
• The debug level applies to all debug types that are configured. You cannot set different levels for each
debug type.
• When the debug level is set to 0, the log is turned off.
Examples
-> ip rip debug-level 3
Release History
Release 5.1; command was introduced.
Related Commands
Configures the type of RIP messages to debug.
Displays the current RIP debug levels and types.
MIB Objects
alaRipLogTable
alaRipDebugLevel
page -36
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
show ip rip debug
Displays the current RIP debug levels and types.
show ip rip debug
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> show ip rip debug
Debug Level
Types/Sections
error
warning
recv
send
rdb
age
config
redist
info
setup
time
= 3
= on
= on
= on
= on
= on
= on
= on
= on
= on
= on
= on
output definitions
Debug Level
Debug level. The valid range 0–255. The default level is 0.
Types/Selections
a description of debug types.
Release History
Release 5.1; command was introduced.
OmniSwitch Troubleshooting Guide September 2005
page -37
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Configures RIP debugging level.
Configures the type of RIP messages to debug.
MIB Objects
dispDrcRipDebug
page -38
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug slot information
Displays all the information about a specific slot. It includes all the details about the ports, statistics,
MDIX, IPC pools, and other phy-related information.
debug slot information slot
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
Examples
-> debug slot information 1
#########################################
debug interfaces 1 backpressure
#########################################
Slot Backpressure
------+--------------
1
disable
#########################################
show interfaces 1 counters
#########################################
1/16,
InOctets
=
258342824, OutOctets
=
241185604,
628318,
99632,
2488,
InUcastPkts =
InMcastPkts =
InBcastPkts =
InPauseFrames =
1/18,
1198288, OutUcastPkts =
132887, OutMcastPkts =
639052, OutBcastPkts =
0, OutPauseFrames =
0
InOctets
=
24973594, OutOctets
=
102309903,
481006,
134096,
639437,
0
InUcastPkts =
InMcastPkts =
InBcastPkts =
InPauseFrames =
1/20,
316757, OutUcastPkts =
354, OutMcastPkts =
2172, OutBcastPkts =
0, OutPauseFrames =
InOctets
=
1504323, OutOctets
=
77527634,
172421,
133117,
641403,
InUcastPkts =
InMcastPkts =
InBcastPkts =
9547, OutUcastPkts =
1333, OutMcastPkts =
196, OutBcastPkts =
OmniSwitch Troubleshooting Guide September 2005
page -39
Download from Www.Somanuals.com. All Manuals Search And Download.
InPauseFrames =
0, OutPauseFrames =
0
#########################################
debug interfaces 1 Led
#########################################
Slot/Port Activity LNK
-----------+----------+--------
1/1
1/2
1/3
1/4
1/5
1/6
1/7
1/8
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
1/9
1/10
1/11
1/12
1/13
1/14
1/15
1/16
1/17
1/18
1/19
1/20
1/21
1/22
1/23
1/24
#########################################
debug interfaces 1 mdix
#########################################
1/1
1/2
1/3
1/4
1/5
1/6
1/7
1/8
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
enable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
enable enable
disable enable
disable enable
disable enable
enable enable
1/9
1/10
1/11
1/12
1/13
1/14
1/15
1/16
1/17
1/18
1/19
1/20
1/21
1/22
1/23
1/24
page -40
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
#########################################
debug ipc pools slot 1
#########################################
IPC Pools slot 1, slice 0:
UrgentPool: Full size is 256, remaining: 256
In socket queues: 0 Not queued: 0:
In DMA queues: 0
ControlPool: Full size is 1024, remaining: 1023
In socket queues: 0 Not queued: 1:
In DMA queues: 0
NormalPool: Full size is 256, remaining: 255
In socket queues: 0 Not queued: 1:
In DMA queues: 0
JumboPool: Full size is 64, remaining: 64
In socket queues: 0 Not queued: 0:
In DMA queues: 0
LocalPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
#########################################
debug interfaces 1 phy
#########################################
slot/port( 1/1 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c429
0 202
0 210
0
0
slot/port( 1/2 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c42b
0 202
0 210
0
0
slot/port( 1/3 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c42b
0 202
0 210
0
0
slot/port( 1/4 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c42b
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
0 202
0 210
0
0
OmniSwitch Troubleshooting Guide September 2005
page -41
Download from Www.Somanuals.com. All Manuals Search And Download.
slot/port( 1/5 ):
Phy ID : 1e
0 : 3000 7809
13 78f7 de1
0
0
0
0
4 2801
8 :
10 : 184 100 8000
18 :
0
0
0
0
0
0
0
54 de2
40 100 c429
0 202
0 210
0
0
slot/port( 1/6 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c42b
0 202
0 210
0
0
slot/port( 1/7 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 e100 c42b
0 202
0 210
0
0
slot/port( 1/8 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c42b
0 202
0 210
0
0
slot/port( 1/9 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c425
0 202
0 210
0
0
slot/port( 1/10):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c421
0 202
0 210
0
0
slot/port( 1/11):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c421
0 202
0 210
0
0
slot/port( 1/12):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c421
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
0 202
0 210
0
0
slot/port( 1/13):
Phy ID : 1e
page -42
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c423
0 202
0 210
0
0
slot/port( 1/14):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c423
0 202
0 210
0
0
slot/port( 1/15):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 e100 c423
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
0 202
0 210
0
0
slot/port( 1/16):
Phy ID : 1e
0 : 3000 782d
8 :
10 : 184 7780 8000
18 :
13 78f7 de1 41e1
7 6801
0
0
0
0
0
0
0
0
0
0
f4 de2
0 200
0 210
2
0
c8 100 c423
slot/port( 1/17):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c41b
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
0 202
0 210
0
0
slot/port( 1/18):
Phy ID : 1e
0 : 3000 782d
8 :
10 : 184 6780 8000
18 :
13 78f7 de1 45e1
7 6801
0
0
0
0
0
0
0
0
0
0
f4 de2
0 200
0 210
2
0
c8 100 c41b
slot/port( 1/19):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c41b
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
0 202
0 210
0
0
slot/port( 1/20):
Phy ID : 1e
0 : 3000 782d
8 :
10 : 184 6780 8000
18 :
13 78f7 de1 41e1
7 6801
0
0
0
0
0
0
0
0
0
0
f4 de2
0 200
0 210
2
0
c8 2100 c419
slot/port( 1/21):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
13 78f7 de1
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
0 202
OmniSwitch Troubleshooting Guide September 2005
page -43
Download from Www.Somanuals.com. All Manuals Search And Download.
18 :
0
0
40 100 c419
13 78f7 de1
0
0 210
4 2801
slot/port( 1/22):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
0
0
0
0
0
0
0
0
0
0
0
54 de2
40 100 c41d
0 202
0 210
0
0
slot/port( 1/23):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
54 de2
40 100 c41b
0 202
0 210
0
0
slot/port( 1/24):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 0 1c8 100 c41d
13 78f7 de1
0
0
31
0
4 2801
0
0
0
0
0
0
0
d4 de2
0 202
0 210
0
#########################################
debug interfaces 1 mac
#########################################
ERROR: Type <0> for Debug_mac is unknown
#########################################
debug interfaces 1 port structure
#########################################
slot/port = ( 1/1 )
slice = 0 mac_chip = 0
index = 0x 3e9
gport = 0x
0
Mac = 0x00:d0:95:6a:5f:28
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw = 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:28
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
0
slot/port = ( 1/2 )
slice = 0 mac_chip = 0
index = 0x 3ea
gport = 0x
1
Mac = 0x00:d0:95:6a:5f:29
prevLink = 0 cur_Link = 2
linkUptime=
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:29
long = 1 long sz =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
page -44
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
runt = 0 runt sz = 0
flowstate = 0 flowmode =
0
flowwait =
0
0
slot/port = ( 1/3 )
slice = 0 mac_chip = 0
index = 0x 3eb
gport = 0x
2
Mac = 0x00:d0:95:6a:5f:2a
prevLink = 0 cur_Link = 2
linkUptime=
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2a
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/4 )
slice = 0 mac_chip = 0
index = 0x 3ec
gport = 0x
3
Mac = 0x00:d0:95:6a:5f:2b
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2b
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/5 )
slice = 0 mac_chip = 0
index = 0x 3ed
gport = 0x
4
Mac = 0x00:d0:95:6a:5f:2c
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2c
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/6 )
slice = 0 mac_chip = 0
index = 0x 3ee
gport = 0x
5
Mac = 0x00:d0:95:6a:5f:2d
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2d
pause DA = 0x 1:80:c2: 0: 0: 1
OmniSwitch Troubleshooting Guide September 2005
page -45
Download from Www.Somanuals.com. All Manuals Search And Download.
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
1553
0
flowwait =
0
0
slot/port = ( 1/7 )
slice = 0 mac_chip = 0
index = 0x 3ef
gport = 0x
6
Mac = 0x00:d0:95:6a:5f:2e
prevLink = 0 cur_Link = 2
linkUptime=
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2e
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/8 )
slice = 0 mac_chip = 0
index = 0x 3f0
gport = 0x
7
Mac = 0x00:d0:95:6a:5f:2f
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2f
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/9 )
slice = 0 mac_chip = 0
index = 0x 3f1
gport = 0x
8
Mac = 0x00:d0:95:6a:5f:30
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:30
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/10)
slice = 0 mac_chip = 0
index = 0x 3f2
gport = 0x
9
Mac = 0x00:d0:95:6a:5f:31
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
page -46
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
pause SA = 0x 0:d0:95:6a:5f:31
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/11)
slice = 0 mac_chip = 0
index = 0x 3f3
gport = 0x
a
Mac = 0x00:d0:95:6a:5f:32
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:32
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/12)
slice = 0 mac_chip = 0
index = 0x 3f4
gport = 0x
b
Mac = 0x00:d0:95:6a:5f:33
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:33
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/13)
slice = 0 mac_chip = 1
index = 0x 3f5
gport = 0x
10
Mac = 0x00:d0:95:6a:5f:34
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:34
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/14)
slice = 0 mac_chip = 1
index = 0x 3f6
gport = 0x
11
Mac = 0x00:d0:95:6a:5f:35
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
OmniSwitch Troubleshooting Guide September 2005
page -47
Download from Www.Somanuals.com. All Manuals Search And Download.
trap
= 0
pause SA = 0x 0:d0:95:6a:5f:35
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/15)
slice = 0 mac_chip = 1
index = 0x 3f7
gport = 0x
12
Mac = 0x00:d0:95:6a:5f:36
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:36
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/16)
slice = 0 mac_chip = 1
index = 0x 3f8
gport = 0x
13
Mac = 0x00:d0:95:6a:5f:37
prevLink = 0 cur_Link = 1
linkUptime=3f79780e
bw = 3 duplex = 3
admin = 1 auto
= 1
d_bw = 100 d_duplex = 1
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:37
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/17)
slice = 0 mac_chip = 1
index = 0x 3f9
gport = 0x
14
Mac = 0x00:d0:95:6a:5f:38
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:38
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/18)
slice = 0 mac_chip = 1
index = 0x 3fa
gport = 0x
15
Mac = 0x00:d0:95:6a:5f:39
prevLink = 0 cur_Link = 1
linkUptime=3f79780e
bw = 3 duplex = 3
admin = 1 auto
d_bw = 100 d_duplex = 1
mtu 1553 flood =
= 1
=
1
flood lmt =
1
page -48
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
ifg
=
12
backoff =
0
trap
= 0
pause SA = 0x 0:d0:95:6a:5f:39
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/19)
slice = 0 mac_chip = 1
index = 0x 3fb
gport = 0x
16
Mac = 0x00:d0:95:6a:5f:3a
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3a
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/20)
slice = 0 mac_chip = 1
index = 0x 3fc
gport = 0x
17
Mac = 0x00:d0:95:6a:5f:3b
prevLink = 0 cur_Link = 1
linkUptime=3f79780e
bw = 3 duplex = 3
admin = 1 auto
= 1
d_bw = 100 d_duplex = 1
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3b
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
0
slot/port = ( 1/21)
slice = 0 mac_chip = 1
index = 0x 3fd
gport = 0x
18
Mac = 0x00:d0:95:6a:5f:3c
prevLink = 0 cur_Link = 2
linkUptime=
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3c
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/22)
slice = 0 mac_chip = 1
index = 0x 3fe
gport = 0x
19
Mac = 0x00:d0:95:6a:5f:3d
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
OmniSwitch Troubleshooting Guide September 2005
page -49
Download from Www.Somanuals.com. All Manuals Search And Download.
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3d
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/23)
slice = 0 mac_chip = 1
index = 0x 3ff
gport = 0x
1a
Mac = 0x00:d0:95:6a:5f:3e
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3e
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/24)
slice = 0 mac_chip = 1
index = 0x 400
gport = 0x
1b
Mac = 0x00:d0:95:6a:5f:3f
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3f
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -50
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces set backpressure
Enables and disables fabric back pressure on a Network Interface (NI) or an entire chassis.
debug interfaces set [slot] backpressure {enable | disable}
Syntax Definitions
slot
The slot number to enable or disable fabric back pressure. The valid
range is 1–8 on an OmniSwitch 7700, 1–16 on an OmniSwitch 7800,
and 1–16 on an OmniSwitch 8800.
enable
disable
Enables fabric backpressure.
Disables fabric backpressure.
Defaults
parameter
default
enable | disable
disable
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
If the slot number is not specified then the switch back pressure feature will be enabled or disabled on an
entire chassis.
Examples
-> debug interfaces set backpressure enable
-> debug interfaces set backpressure disable
-> debug interfaces set 3 backpressure enable
-> debug interfaces set 3 backpressure disable
Release History
Release 5.1; command was introduced.
Related Commands
an entire chassis.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -51
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces backpressure
Displays if fabric back pressure is enabled or disabled on a Network Interface (NI) or an entire chassis.
debug interfaces [slot] backpressure
Syntax Definitions
slot
The slot number to display the fabric back pressure state. The valid
range is 1–8 on an OmniSwitch 7700 and 1–16 on an OmniSwitch 7800,
and 1–16 on an OmniSwitch 8800.
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
If the slot number is not specified then the switch back pressure state will be displayed for an entire chas-
sis.
Examples
-> debug interfaces backpressure
Slot Backpressure
------+--------------
1
2
3
4
5
6
7
8
disable
disable
enable
enable
disable
disable
disable
enable
-> debug interfaces 3 backpressure
Slot Backpressure
------+--------------
3
enable
output definitions
Slot
The slot number of the NI.
Backpressure
Displays if the switch fabric back pressure feature is enabled or dis-
abled on this NI. (The default is disabled.)
Release History
Release 5.1; command was introduced.
page -52
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Enables and disables fabric back pressure on an NI or an entire
chassis.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -53
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces led
Displays LED information.
debug interfaces slot led
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug interfaces 1 led
Slot/Port Activity LNK
-----------+----------+--------
1/1
1/2
1/3
1/4
1/5
1/6
1/7
1/8
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
normal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
1/9
1/10
1/11
1/12
1/13
1/14
1/15
1/16
1/17
1/18
1/19
1/20
1/21
1/22
1/23
1/24
page -54
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -55
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces mdix
Displays Media Dependent Interface with Crossover (MDIX) information.
debug interfaces slot mdix
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug interfaces 1 mdix
1/1
1/2
1/3
1/4
1/5
1/6
1/7
1/8
disable enable
disable enable
disable enable
disable enable
enable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
enable enable
disable enable
disable enable
disable enable
disable enable
disable enable
disable enable
enable enable
enable enable
disable enable
disable enable
disable enable
1/9
1/10
1/11
1/12
1/13
1/14
1/15
1/16
1/17
1/18
1/19
1/20
1/21
1/22
1/23
1/24
Release History
Release 5.1; command was introduced.
page -56
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -57
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces phy
Displays PHY information.
debug interfaces slot phy
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug interfaces 1 phy
slot/port( 1/1 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c429
0 202
0 210
0
0
slot/port( 1/2 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c42b
0 202
0 210
0
0
slot/port( 1/3 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c42b
0 202
0 210
0
0
slot/port( 1/4 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c42b
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
0 202
0 210
0
0
slot/port( 1/5 ):
Phy ID : 1e
page -58
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 e100 c429
0 202
0 210
0
0
slot/port( 1/6 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c42b
0 202
0 210
0
0
slot/port( 1/7 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c42b
0 202
0 210
0
0
slot/port( 1/8 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c42b
0 202
0 210
0
0
slot/port( 1/9 ):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c425
0 202
0 210
0
0
slot/port( 1/10):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c421
0 202
0 210
0
0
slot/port( 1/11):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c421
0 202
0 210
0
0
slot/port( 1/12):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c421
0 202
0 210
0
0
slot/port( 1/13):
Phy ID : 1e
0 : 3000 7809
8 :
13 78f7 de1
0
0
4 2801
0
0
0
0
0
0
0
OmniSwitch Troubleshooting Guide September 2005
page -59
Download from Www.Somanuals.com. All Manuals Search And Download.
10 : 184 100 8000
18 :
0 de2
40 100 c423
0
0
0 202
0 210
0
0
slot/port( 1/14):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c423
0 202
0 210
0
0
slot/port( 1/15):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c423
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
0 202
0 210
0
0
slot/port( 1/16):
Phy ID : 1e
0 : 3000 782d
8 :
10 : 184 7780 8000
18 :
13 78f7 de1 41e1
5 6801
0
0
0
0
0
0
0
0
0
0
0 de2
0 200
0 210
2
0
88 100 c423
slot/port( 1/17):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c41b
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
0 202
0 210
0
0
slot/port( 1/18):
Phy ID : 1e
0 : 3000 782d
8 :
10 : 184 4780 8000
18 :
13 78f7 de1 45e1
5 6801
0
0
0
0
0
0
0
0
0
0
0 de2
0 200
0 210
2
0
88 100 c41b
slot/port( 1/19):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c41b
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
0 202
0 210
0
0
slot/port( 1/20):
Phy ID : 1e
0 : 3000 782d
8 :
10 : 184 4780 8000
18 :
13 78f7 de1 41e1
5 6801
0
0
0
0
0
0
0
0
0
0
0 de2
0 200
0 210
2
0
88 2100 c419
slot/port( 1/21):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c419
slot/port( 1/22):
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
0 202
0 210
0
0
page -60
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c41d
0 202
0 210
0
0
slot/port( 1/23):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 :
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
40 100 c41b
0 202
0 210
0
0
slot/port( 1/24):
Phy ID : 1e
0 : 3000 7809
8 :
10 : 184 100 8000
18 : 40 100 c41d
13 78f7 de1
0
0
0
0
4 2801
0
0
0
0
0
0
0
0 de2
0 202
0 210
0
0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -61
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces mac
Displays MAC information.
debug interfaces slot mac
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug interfaces 1 mac
ERROR: Type <0> for Debug_mac is unknown
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -62
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces port structure
Displays port structure information.
debug interfaces slot port structure
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug interfaces 1 port structure
slot/port = ( 1/1 )
slice = 0 mac_chip = 0
index = 0x 3e9
gport = 0x
0
Mac = 0x00:d0:95:6a:5f:28
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:28
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/2 )
slice = 0 mac_chip = 0
index = 0x 3ea
gport = 0x
1
Mac = 0x00:d0:95:6a:5f:29
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:29
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
OmniSwitch Troubleshooting Guide September 2005
page -63
Download from Www.Somanuals.com. All Manuals Search And Download.
slot/port = ( 1/3 )
slice = 0 mac_chip = 0
index = 0x 3eb
gport = 0x
2
Mac = 0x00:d0:95:6a:5f:2a
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2a
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/4 )
slice = 0 mac_chip = 0
index = 0x 3ec
gport = 0x
3
Mac = 0x00:d0:95:6a:5f:2b
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2b
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/5 )
slice = 0 mac_chip = 0
index = 0x 3ed
gport = 0x
4
Mac = 0x00:d0:95:6a:5f:2c
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2c
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/6 )
slice = 0 mac_chip = 0
index = 0x 3ee
gport = 0x
5
Mac = 0x00:d0:95:6a:5f:2d
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2d
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
page -64
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
slot/port = ( 1/7 )
slice = 0 mac_chip = 0
index = 0x 3ef
gport = 0x
6
Mac = 0x00:d0:95:6a:5f:2e
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2e
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/8 )
slice = 0 mac_chip = 0
index = 0x 3f0
gport = 0x
7
Mac = 0x00:d0:95:6a:5f:2f
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:2f
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/9 )
slice = 0 mac_chip = 0
index = 0x 3f1
gport = 0x
8
Mac = 0x00:d0:95:6a:5f:30
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:30
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/10)
slice = 0 mac_chip = 0
index = 0x 3f2
gport = 0x
9
Mac = 0x00:d0:95:6a:5f:31
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:31
long = 1 long sz =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
runt = 0 runt sz = 0
OmniSwitch Troubleshooting Guide September 2005
page -65
Download from Www.Somanuals.com. All Manuals Search And Download.
flowstate = 0 flowmode =
0
flowwait =
0
0
slot/port = ( 1/11)
slice = 0 mac_chip = 0
index = 0x 3f3
gport = 0x
a
Mac = 0x00:d0:95:6a:5f:32
prevLink = 0 cur_Link = 2
linkUptime=
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:32
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/12)
slice = 0 mac_chip = 0
index = 0x 3f4
gport = 0x
b
Mac = 0x00:d0:95:6a:5f:33
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:33
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/13)
slice = 0 mac_chip = 1
index = 0x 3f5
gport = 0x
10
Mac = 0x00:d0:95:6a:5f:34
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:34
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/14)
slice = 0 mac_chip = 1
index = 0x 3f6
gport = 0x
11
Mac = 0x00:d0:95:6a:5f:35
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:35
long = 1 long sz =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
page -66
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
runt = 0 runt sz = 0
flowstate = 0 flowmode =
0
flowwait =
0
0
slot/port = ( 1/15)
slice = 0 mac_chip = 1
index = 0x 3f7
gport = 0x
12
Mac = 0x00:d0:95:6a:5f:36
prevLink = 0 cur_Link = 2
linkUptime=
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:36
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/16)
slice = 0 mac_chip = 1
index = 0x 3f8
gport = 0x
13
Mac = 0x00:d0:95:6a:5f:37
prevLink = 0 cur_Link = 1
linkUptime=3f79780e
bw = 3 duplex = 3
admin = 1 auto
= 1
d_bw = 100 d_duplex = 1
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:37
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/17)
slice = 0 mac_chip = 1
index = 0x 3f9
gport = 0x
14
Mac = 0x00:d0:95:6a:5f:38
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:38
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/18)
slice = 0 mac_chip = 1
index = 0x 3fa
gport = 0x
15
Mac = 0x00:d0:95:6a:5f:39
prevLink = 0 cur_Link = 1
linkUptime=3f79780e
bw = 3 duplex = 3
admin = 1 auto
= 1
d_bw = 100 d_duplex = 1
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:39
pause DA = 0x 1:80:c2: 0: 0: 1
OmniSwitch Troubleshooting Guide September 2005
page -67
Download from Www.Somanuals.com. All Manuals Search And Download.
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
1553
0
flowwait =
0
0
slot/port = ( 1/19)
slice = 0 mac_chip = 1
index = 0x 3fb
gport = 0x
16
Mac = 0x00:d0:95:6a:5f:3a
prevLink = 0 cur_Link = 2
linkUptime=
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3a
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/20)
slice = 0 mac_chip = 1
index = 0x 3fc
gport = 0x
17
Mac = 0x00:d0:95:6a:5f:3b
prevLink = 0 cur_Link = 1
linkUptime=3f79780e
bw = 3 duplex = 3
admin = 1 auto
= 1
d_bw = 100 d_duplex = 1
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3b
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/21)
slice = 0 mac_chip = 1
index = 0x 3fd
gport = 0x
18
Mac = 0x00:d0:95:6a:5f:3c
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3c
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/22)
slice = 0 mac_chip = 1
index = 0x 3fe
gport = 0x
19
Mac = 0x00:d0:95:6a:5f:3d
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
page -68
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
pause SA = 0x 0:d0:95:6a:5f:3d
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/23)
slice = 0 mac_chip = 1
index = 0x 3ff
gport = 0x
1a
Mac = 0x00:d0:95:6a:5f:3e
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3e
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
slot/port = ( 1/24)
slice = 0 mac_chip = 1
index = 0x 400
gport = 0x
1b
Mac = 0x00:d0:95:6a:5f:3f
prevLink = 0 cur_Link = 2
linkUptime=
0
admin = 1 auto
= 1
bw
= 3 duplex = 3
d_bw = 3 d_duplex = 3
mtu
ifg
trap
=
=
1553
12
flood =
backoff =
1
0
flood lmt =
1
= 0
pause SA = 0x 0:d0:95:6a:5f:3f
long = 1 long sz =
runt = 0 runt sz = 0
flowstate = 0 flowmode =
pause DA = 0x 1:80:c2: 0: 0: 1
1553
0
flowwait =
0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -69
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces mac stats
Displays MAC stats for a slot or slot/port.
debug interfaces {slot | slot/port} mac stats
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
The port number of the interface.
port
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug interfaces 1 mac stats
ERROR: Type <3> for Debug_mac is unknown
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -70
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces mac port
Displays MAC level register information.
debug interfaces {slot | slot/port} mac port
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
The port number of the interface.
port
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug interfaces 1/1 mac port
slot/port(01/01):
100 :
200
4
a66c
0
0 956a5f28
d0 c2000001
611
180
bd4
4
120 :
0
0
0
0
Output fields are described below:
output definitions
Slot
The slot number of the NI.
Port
The port number of the interface.
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -71
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces mac nonport
Displays MAC level information for nonport from the register values.
debug interfaces {slot | slot/port} mac nonport
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
The port number of the interface.
port
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug interfaces 1/1 mac nonport
slot/port(01/01):
Mac Asic Version : 1
0 :
0
b
3
0
0
1ff
10101
3ff577
aa
1ff
1
ff
91
20 : deadbeef deadbeef
f
40 : 80000000 deadbeef deadbeef deadbeef
a
15446
fffff
0
1ffaff
60 :
a
0
5
96
0
ff
0
0 d
eadbeef
80 : ff00000f ff00000f 1f000001
43
a0 :
0
0
ff
201
0
0
3f3f 1000171
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -72
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug interfaces switching
Displays the register value specified in hexadecimal for all the slots or displays a specified number of
register values starting from the hexadecimal address for all the slots.
debug interfaces [slot | slot/port] switching 0xhex [num]
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
The port number of the interface.
port
0Xhex
num
The register value in hexadecimal (e.g., 0xffff).
The number of register values to be displayed.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug interfaces 1 switching 0xffff
ASIC Ver : 1
ffff : d207bff4
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -73
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ipc pools slot
Displays IPC pools on a particular slot.
debug ipc pools slot slot
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug ipc pools slot 1
IPC Pools slot 1, slice 0:
UrgentPool: Full size is 256, remaining: 256
In socket queues: 0 Not queued: 0:
In DMA queues: 0
ControlPool: Full size is 1024, remaining: 1023
In socket queues: 0 Not queued: 1:
In DMA queues: 0
NormalPool: Full size is 256, remaining: 255
In socket queues: 0 Not queued: 1:
In DMA queues: 0
JumboPool: Full size is 64, remaining: 64
In socket queues: 0 Not queued: 0:
In DMA queues: 0
LocalPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
Release History
Release 5.1; command was introduced.
page -74
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Displays IPC Pools on Chassis Management Modules (CMMs).
Displays IPC pools for the Burst Bus with transmit and received
count, Direct Memory Access errors, and parity errors.
Displays all the active sockets on Chassis Management Modules
(CMMs).
Displays all the active sockets on a particular slot.
OmniSwitch Troubleshooting Guide September 2005
page -75
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ipc pools cmm
Displays IPC Pools on Chassis Management Modules (CMMs).
debug ipc pools CMM
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug ipc pools cmm
IPC Pools for CMM:
UrgentPool: Full size is 1024, remaining: 1024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
ControlPool: Full size is 5096, remaining: 5096
In socket queues: 0 Not queued: 0:
In DMA queues: 0
NormalPool: Full size is 2024, remaining: 2024
In socket queues: 0 Not queued: 0:
In DMA queues: 0
JumboPool: Full size is 256, remaining: 255
Socket ID = 0x61, dest slot = 65, remote addr = 0x43430041, ipc status = G
Task ID = 0x4553de0, PayLoad Len= 972, ipc priority = 0x1, data ptr = 0x621a9
10
next = 0x0, pFreeQ = 0x6e9be10, data_offset = 0, free_list_num = 2
In socket queues: 0 Not queued: 1:
In DMA queues: 0
LocalPool: Full size is 64, remaining: 64
In socket queues: 0 Not queued: 0:
In DMA queues: 0
Release History
Release 5.1; command was introduced.
page -76
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Displays IPC pools on a particular slot.
Displays IPC pools for the Burst Bus with transmit and received
count, Direct Memory Access errors, and parity errors.
Displays all the active sockets on Chassis Management Modules
(CMMs).
Displays all the active sockets on a particular slot.
OmniSwitch Troubleshooting Guide September 2005
page -77
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ipc bbus
Displays IPC pools for the Burst Bus with transmit and received count, Direct Memory Access errors, and
parity errors.
debug ipc bbus
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug ipc bbus
Slot|Enabled | Tx Cnt | Rx Cnt |DMA Errs |PT Errs |
----|--------|---------|---------|---------|---------|
1|
2|
1| 570044| 271497|
5977| 106238|
0| 316|
9961| 283391|
0| 0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
1|
0|
1|
0|
1|
1|
1|
1|
1|
1|
1|
3|
4|
5|
6|
9061| 237393|
10755| 233827|
5981| 106051|
10913| 234603|
5951| 109021|
6434| 289241|
5929| 110932|
7|
8|
9|
10|
11|
12|
page -78
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
13|
14|
15|
16|
1|
1|
0|
1|
5944| 106369|
5946| 108400|
0|
0|
0|
0|
0|
0|
0|
0|
0|
0|
5955| 107128|
Release History
Release 5.1; command was introduced.
Related Commands
Displays IPC Pools on Chassis Management Modules (CMMs).
Displays IPC pools on a particular slot.
Displays all the active sockets on Chassis Management Modules
(CMMs).
Displays all the active sockets on a particular slot.
OmniSwitch Troubleshooting Guide September 2005
page -79
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ipc active sockets
Displays all the active sockets on Chassis Management Modules (CMMs).
debug ipc active sockets
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug ipc active sockets
EnterProcessCB
328Falsockcontrolblocksfound
CB ADR |S| LocAdr |RemAdr |TasName|
--------|-|--------|--------|--------|
6E9C108|3|10400041|10400042|tCsC-
SMta
6E9C1D0|2| 6400041|
SMta
6E9C298|2| 9400041|
SMta
6E9C360|2| 8400041|
SMta
6E9C428|2| 7400041|
SMta
0|tCsC-
0|tCsC-
0|tCsC-
0|tCsC-
0|tCsC-
6E9C4F0|2| D400041|
SMta
6E9C5B8|2|12400041| 0|tCS_PTB
6E9C680|2|1400041| 0|tCS_CCM
6E9C748|2|2400041| 0|tCS_CCM
6E9C810|2|5400041| 0|tCS_PRB
6E9C8D8|2|B400041| 0|tCS_CMS
6E9C9A0|2|C400041| 0|tCS_CMS
6E9CA68|2|4400041| 0|tCS_HSM
6E9CB30|2|3400041| 0|tCS_HSM
6E9CBF8|2|A400041| 0|tCS_CVM
6E9CCC0|2|1420041| 0|CfgMgr
6E9CD88|2|2420041| 0|CfgMgr
6E9CE50|2| 3420041|
0|CfgMgr
page -80
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Release History
Release 5.1; command was introduced.
Related Commands
Displays IPC Pools on Chassis Management Modules (CMMs).
Displays IPC pools for the Burst Bus with transmit and received
count, Direct Memory Access errors, and parity errors.
Displays IPC pools on a particular slot.
Displays all the active sockets on a particular slot.
OmniSwitch Troubleshooting Guide September 2005
page -81
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ipc active sockets slot
Displays all the active sockets on a particular slot.
debug ipc active sockets slot slot
Syntax Definitions
slot
The slot number of the Network Interface (NI) module.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug ipc active sockets slot 11
93 Falsock control blocks found slot 11
CB ADR |S|
LocAdr |RemAdr | TaskName|
--------|-|--------|--------|--------|
2A5C18|2|
Task
2A5CE0|2|
Task
2A5DA8|2|
Task
2A5E70|2|
Task
2A5F38|3|
Task
2A6000|2|
Task
2A60C8|3|
Task
2A6190|3|
Task
2A6258|3|
Task
2A6320|3|
Task
2A63E8|3|
Task
2A64B0|3|
Task
303000B|
5000B|
0|
0|
0|
0|
NI
NI
NI
NI
NI
NI
NI
NI
NI
NI
NI
NI
11A000B|
2000B|
115000B| 5000B|
209000B| 0|
909000B| 5000B|
809000B|100B000B|
309000B| 308000B|
A09000B| 303000B|
F09000B| 20A000B|
609000B| 6000B|
page -82
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
2A6578|2|
Task
2A6640|3|
Task
2A6708|3|
Task
2A67D0|3|
Task
2A6898|3|
Task
2A6960|3|
Task
208000B|
0|
NI
NI
NI
NI
NI
NI
A08000B| 5000B|
908000B|100B000B|
308000B| 309000B|
708000B| 6000B|
F08000B| 20A000B|
Release History
Release 5.1; command was introduced.
Related Commands
Displays IPC Pools on Chassis Management Modules (CMMs).
Displays IPC pools for the Burst Bus with transmit and received
count, Direct Memory Access errors, and parity errors.
Displays all the active sockets on Chassis Management Modules
(CMMs).
Displays IPC pools on a particular slot.
OmniSwitch Troubleshooting Guide September 2005
page -83
Download from Www.Somanuals.com. All Manuals Search And Download.
debug fabric threshold
Displays the threshold number for each fabric ASIC. In addition, it also displays the Unicast pay gener-
ated internally using Pay algorithm and Coupons generated.
debug fabric threshold
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
This command is not valid for OS-6600 series of switches.
Examples
-> debug fabric threshold
NantucketThreshold Ucst Ucst Ucst Ucst Unicast
Number
Number Pay3 Pay2 Pay1 Pay0 Coupon
--------- --------- ---- ---- ---- ---- -------
0
0
0
0
0
0
0
1
2
3
4
5
6
7
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
2d0
2d0
2d0
2d0
2d0
2d0
2d0
0
8
2d0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
2d0
2d0
2d0
2d0
5a0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
page -84
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
20 20 20 20
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
20 20 20 20
330 f0 90 60
2d0
2d0
5a0
2d0
20
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
20
2d0
------- --------- ---- ---- ---- ---- -------
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
OmniSwitch Troubleshooting Guide September 2005
page -85
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
20 20 20 20
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
20 20 20 20
330 f0 90 60
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
20
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
20
2d0
--------- --------- ---- ---- ---- ---- -------
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
page -86
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
20 20 20 20
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
66 28a 180 c0
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
20 20 20 20
330 f0 90 60
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
20
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
46
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
20
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
2d0
--------- --------- ---- ---- ---- ---- -------
3
3
3
3
3
3
3
3
1
2
3
4
5
6
7
8
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
OmniSwitch Troubleshooting Guide September 2005
page -87
Download from Www.Somanuals.com. All Manuals Search And Download.
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
20 20 20 20
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
20 20 20 20
330 f0 90 60
2d0
2d0
2d0
2d0
5a0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
20
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
20
2d0
--------- --------- ---- ---- ---- ---- -------
4
4
1
2
330 f0 90 60
330 f0 90 60
2d0
2d0
page -88
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
3
4
5
6
7
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
660 28a 180 c0
330 f0 90 60
20 20 20 20
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
330 f0 90 60
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
5a0
2d0
20
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
2d0
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Release History
Release 5.1; command was introduced.
Related Commands
Displays the overall status of all the fabric ASICs.
Displays the fabric ASIC statistics.
OmniSwitch Troubleshooting Guide September 2005
page -89
Download from Www.Somanuals.com. All Manuals Search And Download.
debug fabric status
Displays the overall status of all the fabric ASICs. It displays the chip version and netlist version being
used. In addition, it also displays if any internal or external interrupts were received.
debug fabric status
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
This command is not valid for OS-6600 series of switches.
Examples
-> debug fabric status
Nantucket Chip Netlist Internal External
Number Version Version Interrupts Interrupts
--------- ------- ------- ---------- ----------
0
1
2
3
4
5
6
7
1
1
1
1
1
1
1
1
8
8
8
8
8
8
8
8
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
RFL Count RLS Count NBI Count NBE Count FL Count
--------- --------- --------- --------- --------
0
0
0
0
0
Release History
Release 5.1; command was introduced.
Related Commands
Displays the fabric ASIC statistics.
page -90
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug fabric stats
Displays the fabric ASIC statistics.
debug fabric stats
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command is not valid for OS-6600 series of switches.
• “Unicast In” should be equal to the “Unicast Out”.
• For Multicast, multicast in will be different from multicast out. Iteration of this command should show
the queues moving.
Examples
-> debug fabric stats
Nantucket Unicast Unicast Unicast Dummy
Number
In
Out Attempt Count
--------- ------- ------- ------- -------
0
1
2
3
4
5
6
7
884282 884282 884282 140584
884282 884282 884282 140584
884283 884283 884283 140584
884283 884283 884283 140584
884283 884283 884283 140584
884283 884283 884283 140584
884283 884284 884284 140584
884284 884284 884284 140584
NantucketMulticast Multicast Multicast
Number In Out Attempt
--------- --------- --------- ---------
0
1
2
3
4
5
6
7
269345
269345
269345
269345
269345
269345
269345
269345
631193
631193
631193
631193
631193
631193
631193
631193
269345
269345
269345
269345
269345
269345
269345
269345
OmniSwitch Troubleshooting Guide September 2005
page -91
Download from Www.Somanuals.com. All Manuals Search And Download.
Release History
Release 5.1; command was introduced.
Related Commands
Displays the overall status of all the fabric ASICs.
page -92
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug fabric output
Displays the fabric ASIC port number and the frame count.
debug fabric output
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command is not valid for OS-6600 series of switches.
• Each fabric ASIC has 16 ports in case of 7800 and 8 port in case of 7700.
• The frame count on the similar ports for all the fabric ASICs should be same.
Examples
-> debug fabric output
Nantucket Port Frame
Number Number Count
--------- ------ -------
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
2
3
4
5
6
7
8
55509
59200
55029
55110
45451
47993
31451
45447
47328
47327
9005
59975
59988
45449
48030
62795
9
10
11
12
13
14
15
--------- ------ -------
1
1
1
1
1
1
0
1
2
3
4
5
55509
59200
55029
55110
45451
47993
OmniSwitch Troubleshooting Guide September 2005
page -93
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
1
1
1
1
1
1
1
1
6
7
8
31451
45447
47328
47327
9006
59975
59988
45449
48030
62795
9
10
11
12
13
14
15
--------- ------ -------
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
0
1
2
3
4
5
6
7
8
55509
59200
55029
55110
45451
47993
31452
45447
47328
47327
9006
59975
59988
45449
48030
62795
9
10
11
12
13
14
15
--------- ------ -------
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
0
1
2
3
4
5
6
7
8
55509
59202
55029
55110
45451
47993
31452
45447
47328
47327
9006
59975
59988
45449
48030
62795
9
10
11
12
13
14
15
--------- ------ -------
4
4
4
4
4
4
4
4
4
4
4
4
4
4
0
1
2
3
4
5
6
7
8
55509
59202
55029
55110
45451
47993
31452
45447
47328
47327
9008
9
10
11
12
13
59975
59988
45449
page -94
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
4
4
14
15
48030
62795
--------- ------ -------
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
0
1
2
3
4
5
6
7
8
55509
59202
55029
55110
45451
47993
31452
45449
47328
47327
9008
59975
59988
45449
48031
62795
9
10
11
12
13
14
15
--------- ------ -------
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
0
1
2
3
4
5
6
7
8
55509
59202
55029
55110
45451
47993
31452
45450
47328
47327
9008
59975
59988
45449
48032
62795
9
10
11
12
13
14
15
--------- ------ -------
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
0
1
2
3
4
5
6
7
8
55509
59202
55029
55110
45452
47993
31452
45450
47328
47327
9008
59975
59988
45449
48032
62795
9
10
11
12
13
14
15
Release History
Release 5.1; command was introduced.
OmniSwitch Troubleshooting Guide September 2005
page -95
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Displays the overall status of all the fabric ASICs.
Displays the fabric ASIC statistics.
page -96
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug fabric mcvectors
Displays the Fabric ASIC port number and the frame count for multicast packets.
debug fabric mcvectors
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command is not valid for OS-6600 series of switches.
• Each fabric ASIC has 16 ports in case of 7800 and 8 port in case of 7700.
• The frame count on the similar ports for all the fabric ASICs should be same.
Examples
->debug fabric mcvector
Nantucket Vlan Multicast
Number Number Vector
--------- ------ ---------
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
50
51
52
53
54
55
56
57
58
59
60
61
de6d
404
404
404
404
404
404
404
404
404
404
404
404
404
5
62
100
102
103
104
105
4
4
44
44
0
0
0
0
106
4
4
24
24
107
108
109
OmniSwitch Troubleshooting Guide September 2005
page -97
Download from Www.Somanuals.com. All Manuals Search And Download.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
110
111
112
114
115
116
117
130
140
141
150
211
212
311
411
511
611
711
c
c
4004
1006
4
4
804
804
7
5
586d
4004
1004
4
4
5
6
4
--------- ------ ---------
1
1
50
de6d
404
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
51
52
53
54
55
56
57
58
59
60
61
62
100
102
103
104
105
106
107
108
109
110
111
112
114
115
116
117
130
140
141
150
211
212
311
411
511
611
404
404
404
404
404
404
404
404
404
404
404
404
5
4
4
44
44
4
4
24
24
c
c
4004
1006
4
4
804
804
7
5
586d
4004
1004
4
4
5
6
page -98
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
1
711
4
--------- ------ ---------
2
2
2
2
2
2
2
1
50
51
52
53
54
55
56
57
58
de6d
404
404
404
404
404
404
404
404
404
404
404
404
404
5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
59
60
61
62
100
102
103
104
105
106
107
108
109
110
111
112
114
115
116
117
130
140
141
150
211
212
311
411
511
611
711
4
4
44
44
4
4
24
24
c
c
4004
1006
4
4
804
804
7
5
586d
4004
1004
4
4
5
6
4
--------- ------ ---------
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
1
50
51
52
53
54
55
56
57
58
59
60
61
62
100
de6d
404
404
404
404
404
404
404
404
404
404
404
404
404
5
OmniSwitch Troubleshooting Guide September 2005
page -99
Download from Www.Somanuals.com. All Manuals Search And Download.
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
102
103
104
105
106
107
108
109
110
111
112
114
115
116
117
130
140
141
150
211
212
311
411
511
611
711
4
4
44
44
4
4
24
24
c
c
4004
1006
4
4
804
804
7
5
586d
4004
1004
4
4
5
6
4
--------- ------ ---------
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
1
50
51
52
53
54
55
56
57
58
59
60
61
de6d
404
404
404
404
404
404
404
404
404
404
404
404
404
5
62
100
102
103
104
105
106
107
108
109
110
111
112
114
115
116
117
130
140
4
4
44
44
4
4
24
24
c
c
4004
1006
4
4
804
804
7
page -100
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
4
4
4
4
4
4
4
4
4
141
150
211
212
311
411
511
611
711
5
586d
4004
1004
4
4
5
6
4
--------- ------ ---------
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
1
50
51
52
53
54
55
56
57
58
59
60
61
de6d
404
404
404
404
404
404
404
404
404
404
404
404
404
5
62
100
102
103
104
105
106
107
108
109
110
111
112
114
115
116
117
130
140
141
150
211
212
311
411
511
611
711
4
4
44
44
4
4
24
24
c
c
4004
1006
4
4
804
804
7
5
586d
4004
1004
4
4
5
6
4
--------- ------ ---------
6
6
6
6
6
6
6
1
50
51
52
53
54
55
de6d
404
404
404
404
404
404
OmniSwitch Troubleshooting Guide September 2005
page -101
Download from Www.Somanuals.com. All Manuals Search And Download.
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
56
57
58
59
60
404
404
404
404
404
404
404
5
4
4
44
44
4
61
62
100
102
103
104
105
106
107
108
109
110
111
112
114
115
116
117
130
140
141
150
211
212
311
411
511
611
711
4
24
24
c
c
4004
1006
4
4
804
804
7
5
586d
4004
1004
4
4
5
6
4
--------- ------ ---------
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
1
50
51
52
53
54
55
56
57
58
59
60
61
de6d
404
404
404
404
404
404
404
404
404
404
404
404
404
5
62
100
102
103
104
105
106
107
108
109
110
4
4
44
44
4
4
24
24
c
page -102
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
111
112
114
115
116
117
130
140
141
150
211
212
311
411
511
611
711
c
4004
1006
4
4
804
804
7
5
586d
4004
1004
4
4
5
6
4
Release History
Release 5.1; command was introduced.
Related Commands
Displays the overall status of all the fabric ASICs.
Displays the fabric ASIC statistics.
OmniSwitch Troubleshooting Guide September 2005
page -103
Download from Www.Somanuals.com. All Manuals Search And Download.
debug fabric input
Displays the fabric ASIC port number, frame count, and error count.
debug fabric input
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command is not valid for OS-6600 series of switches.
• Each fabric ASIC has 16 ports in case of 7800 and 8 port in case of 7700.
• The frame count on the similar ports for all the fabric ASICs should be same.
• There should be no errors on any fabric.
Examples
-> debug fabric input
Nantucket Port
Frame Error
Number Number Count Count
--------- ------ ------- -------
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 5405287
1 5129581
2 5135540
3 5149705
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
0
5 5157878
6 5170104
7
0
8 5125861
9 5134184
10 5281984
11 5134611
12 5135085
13
0
14 5157432
15 5135397
--------- ------ ------- -------
1
1
1
1
1
0 5405287
1 5129581
2 5135540
3 5149705
0
0
0
0
0
4
0
page -104
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
1
1
1
1
1
1
1
1
1
5 5157878
6 5170104
0
0
0
0
0
0
0
0
0
0
0
7
0
8 5125861
9 5134184
10 5281984
11 5134611
12 5135085
13
0
14 5157433
15 5135397
--------- ------ ------- -------
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
0 5405287
1 5129581
2 5135540
3 5149706
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
0
5 5157878
6 5170105
7
0
8 5125862
9 5134184
10 5281985
11 5134612
12 5135085
13
0
14 5157433
15 5135397
--------- ------ ------- -------
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
0 5405287
1 5129582
2 5135540
3 5149706
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
0
5 5157878
6 5170105
7
0
8 5125862
9 5134185
10 5281985
11 5134612
12 5135085
13
0
14 5157433
15 5135398
--------- ------ ------- -------
4
4
4
4
4
4
4
4
4
4
4
4
4
0 5405287
1 5129582
2 5135540
3 5149706
0
0
0
0
0
0
0
0
0
0
0
0
0
4
0
5 5157878
6 5170105
7
0
8 5125862
9 5134185
10 5281985
11 5134612
12 5135086
OmniSwitch Troubleshooting Guide September 2005
page -105
Download from Www.Somanuals.com. All Manuals Search And Download.
4
4
4
13
0
0
0
0
14 5157433
15 5135398
--------- ------ ------- -------
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
0 5405287
1 5129582
2 5135541
3 5149706
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
0
5 5157879
6 5170105
7
0
8 5125862
9 5134185
10 5281985
11 5134612
12 5135086
13
0
14 5157434
15 5135398
--------- ------ ------- -------
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
0 5405287
1 5129582
2 5135541
3 5149706
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
0
5 5157879
6 5170105
7
0
8 5125862
9 5134185
10 5281985
11 5134612
12 5135086
13
0
14 5157434
15 5135398
--------- ------ ------- -------
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
0 5405287
1 5129582
2 5135541
3 5149707
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
0
5 5157879
6 5170106
7
0
8 5125863
9 5134185
10 5281986
11 5134613
12 5135086
13
0
14 5157434
15 5135398
Release History
Release 5.1; command was introduced.
page -106
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Displays the overall status of all the fabric ASICs.
Displays the fabric ASIC statistics.
OmniSwitch Troubleshooting Guide September 2005
page -107
Download from Www.Somanuals.com. All Manuals Search And Download.
debug fabric fbus
Displays the fabric ASIC port number and the synchronization status for all the FBUSs.
debug fabric fbus
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command is not valid for OS-6600 series of switches.
• Each fabric ASIC has 16 ports in case of 7800 and 8 port in case of 7700.
• The synchronization status on the similar ports for all the fabric ASICs should be same.
Examples
-> debug fabric fbus
Nantucket Port Descrambler 8b9b Link
Number Number
Lock
Lock In Sync
--------- ------ ----------- ------ -------
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
2
3
4
5
6
7
8
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
9
10
11
12
13
14
15
Yes
Yes
Yes
Yes
Yes
Yes
--------- ------ ----------- ------ -------
1
1
1
1
1
1
0
1
2
3
4
5
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
page -108
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
1
1
1
1
1
1
1
1
6
7
8
Yes
No
Yes
No
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
9
10
11
12
13
14
15
Yes
Yes
Yes
Yes
Yes
Yes
--------- ------ ----------- ------ -------
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
0
1
2
3
4
5
6
7
8
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
9
10
11
12
13
14
15
Yes
Yes
Yes
Yes
Yes
Yes
--------- ------ ----------- ------ -------
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
0
1
2
3
4
5
6
7
8
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
9
10
11
12
13
14
15
Yes
Yes
Yes
Yes
Yes
Yes
--------- ------ ----------- ------ -------
4
4
4
4
4
4
4
4
4
4
4
4
4
4
0
1
2
3
4
5
6
7
8
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
9
10
11
12
13
OmniSwitch Troubleshooting Guide September 2005
page -109
Download from Www.Somanuals.com. All Manuals Search And Download.
4
4
14
15
Yes
Yes
Yes
Yes
Yes
Yes
--------- ------ ----------- ------ -------
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
0
1
2
3
4
5
6
7
8
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
9
10
11
12
13
14
15
Yes
Yes
Yes
Yes
Yes
Yes
--------- ------ ----------- ------ -------
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
0
1
2
3
4
5
6
7
8
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
9
10
11
12
13
14
15
Yes
Yes
Yes
Yes
Yes
Yes
--------- ------ ----------- ------ -------
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
0
1
2
3
4
5
6
7
8
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
9
10
11
12
13
14
15
Yes
Yes
Yes
Yes
Yes
Yes
Release History
Release 5.1; command was introduced.
page -110
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Displays the overall status of all the fabric ASICs.
Displays the fabric ASIC statistics.
OmniSwitch Troubleshooting Guide September 2005
page -111
Download from Www.Somanuals.com. All Manuals Search And Download.
debug fabric errors
Displays the errors detected for all the fabric ASICs on a switch.
debug fabric errors
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
This command is only not for OS-6600 series of switches.
Examples
- >debug fabric errors
Nantucket B04 B08 Framing Parity
Number Error Error Error Error
--------- ----- ----- ------- ------
0
1
2
3
4
5
6
7
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Release History
Release 5.1; command was introduced.
Related Commands
Displays the overall status of all the fabric ASICs.
Displays the fabric ASIC statistics.
page -112
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug fabric calendars
Displays the fabric ASIC port number, calendar number, and the calendar length.
debug fabric calendars
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command is not valid for OS-6600 series of switches.
• Each fabric ASIC has 16 ports in case of 7800 and 8 port in case of 7700.
• The calendar number and length should be the same for all the similar ports on all the fabric ASICs.
Examples
-> debug fabric calendars
Nantucket Calendar Calendar
Number
Number Length
--------- -------- --------
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
24
1
2
24
2
2
24
2
24
2
2
2
24
2
24
--------- -------- --------
1
1
1
1
1
1
1
2
3
4
5
6
2
24
1
2
24
2
OmniSwitch Troubleshooting Guide September 2005
page -113
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
1
1
1
1
1
1
1
1
7
8
9
10
11
12
13
14
15
16
2
24
2
24
2
2
2
24
2
24
--------- -------- --------
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
24
1
2
24
2
2
24
2
24
2
2
2
24
2
24
--------- -------- --------
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
24
1
2
24
2
2
24
2
24
2
2
2
24
2
24
--------- -------- --------
4
4
4
4
4
4
4
4
4
4
4
4
4
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
2
24
1
2
24
2
2
24
2
24
2
2
2
24
page -114
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
4
4
15
16
2
24
--------- -------- --------
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
24
1
2
24
2
2
24
2
24
2
2
2
24
2
24
--------- -------- --------
6
6
6
6
6
6
6
6
6
6
6
6
6
1
2
3
4
5
6
7
8
9
10
11
12
13
2
24
1
2
24
2
2
24
2
24
2
2
2
6
6
6
14
15
16
24
2
24
--------- -------- --------
7
7
7
1
2
3
2
24
1
7
4
2
7
7
5
6
24
2
7
7
2
7
7
8
9
24
2
7
7
7
7
7
7
7
10
11
12
13
14
15
16
24
2
2
2
24
2
24
Nan Cal Cal
Num Num Entry
--- --- ----- --- --- --- --- --- --- --- ---
0 1 1- 8 c 1c 0 0 0 0 0 0
9-16 0 0 0 0 0 0 0 0
17-24 0 0 0 0 0 0 0 0
OmniSwitch Troubleshooting Guide September 2005
page -115
Download from Www.Somanuals.com. All Manuals Search And Download.
25-32 0 0 0 0 0 0 0 0
0 2 1- 8 20 21 22 23 24 25 26 27
9-16 28 29 2a 2b 30 31 32 33
17-24 34 35 36 37 38 39 3a 3b
25-32 20 20 20 20 20 20 20 20
0 3 1- 8 57 41 42 43 44 45 50 51
9-16 52 53 54 55 40 40 40 40
17-24 40 40 40 40 40 40 40 40
25-32 40 40 40 40 40 40 40 40
0 4 1- 8 6c 7c 60 60 60 60 60 60
9-16 60 60 60 60 60 60 60 60
17-24 60 60 60 60 60 60 60 60
25-32 60 60 60 60 60 60 60 60
0 5 1- 8 80 81 82 83 84 85 86 87
9-16 88 89 8a 8b 90 91 92 93
17-24 94 95 96 97 98 99 9a 9b
25-32 80 80 80 80 80 80 80 80
0 6 1- 8 ac bc a0 a0 a0 a0 a0 a0
9-16 a0 a0 a0 a0 a0 a0 a0 a0
17-24 a0 a0 a0 a0 a0 a0 a0 a0
25-32 a0 a0 a0 a0 a0 a0 a0 a0
0 7 1- 8 cc dc c0 c0 c0 c0 c0 c0
9-16 c0 c0 c0 c0 c0 c0 c0 c0
17-24 c0 c0 c0 c0 c0 c0 c0 c0
25-32 c0 c0 c0 c0 c0 c0 c0 c0
0 8 1- 8 e0 e1 e2 e3 e4 e5 e6 e7
9-16 e8 e9 ea eb f0 f1 f2 f3
17-24 f4 f5 f6 f7 f8 f9 fa fb
25-32 e0 e0 e0 e0 e0 e0 e0 e0
0 9 1- 8 10c 11c 100 100 100 100 100 100
9-16 100 100 100 100 100 100 100 100
17-24 100 100 100 100 100 100 100 100
25-32 100 100 100 100 100 100 100 100
0 10 1- 8 120 121 122 123 124 125 126 127
9-16 128 129 12a 12b 130 131 132 133
17-24 134 135 136 137 138 139 13a 13b
25-32 120 120 120 120 120 120 120 120
0 11 1- 8 14c 15c 140 140 140 140 140 140
9-16 140 140 140 140 140 140 140 140
17-24 140 140 140 140 140 140 140 140
25-32 140 140 140 140 140 140 140 140
0 12 1- 8 16c 17c 160 160 160 160 160 160
9-16 160 160 160 160 160 160 160 160
17-24 160 160 160 160 160 160 160 160
25-32 160 160 160 160 160 160 160 160
0 13 1- 8 18c 19c 180 180 180 180 180 180
9-16 180 180 180 180 180 180 180 180
17-24 180 180 180 180 180 180 180 180
25-32 180 180 180 180 180 180 180 180
0 14 1- 8 1a0 1a1 1a2 1a3 1a4 1a5 1a6 1a7
9-16 1a8 1a9 1aa 1ab 1b0 1b1 1b2 1b3
17-24 1b4 1b5 1b6 1b7 1b8 1b9 1ba 1bb
25-32 1a0 1a0 1a0 1a0 1a0 1a0 1a0 1a0
0 15 1- 8 1cc 1dc 1c0 1c0 1c0 1c0 1c0 1c0
9-16 1c0 1c0 1c0 1c0 1c0 1c0 1c0 1c0
17-24 1c0 1c0 1c0 1c0 1c0 1c0 1c0 1c0
25-32 1c0 1c0 1c0 1c0 1c0 1c0 1c0 1c0
0 16 1- 8 1e0 1e1 1e2 1e3 1e4 1e5 1e6 1e7
9-16 1e8 1e9 1ea 1eb 1f0 1f1 1f2 1f3
page -116
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
17-24 1f4 1f5 1f6 1f7 1f8 1f9 1fa 1fb
25-32 1e0 1e0 1e0 1e0 1e0 1e0 1e0 1e0
--- --- ----- --- --- --- --- --- --- --- ---
1 1 1- 8 c 1c 0 0 0 0 0 0
9-16 0 0 0 0 0 0 0 0
17-24 0 0 0 0 0 0 0 0
25-32 0 0 0 0 0 0 0 0
1 2 1- 8 20 21 22 23 24 25 26 27
9-16 28 29 2a 2b 30 31 32 33
17-24 34 35 36 37 38 39 3a 3b
25-32 0 0 0 0 0 0 0 0
1 2 1- 8 20 21 22 23 24 25 26 27
9-16 28 29 2a 2b 30 31 32 33
17-24 34 35 36 37 38 39 3a 3b
25-32 20 20 20 20 20 20 20 20
1 3 1- 8 57 41 42 43 44 45 50 51
9-16 52 53 54 55 40 40 40 40
17-24 40 40 40 40 40 40 40 40
25-32 40 40 40 40 40 40 40 40
1 4 1- 8 6c 7c 60 60 60 60 60 60
9-16 60 60 60 60 60 60 60 60
17-24 60 60 60 60 60 60 60 60
25-32 60 60 60 60 60 60 60 60
1 5 1- 8 80 81 82 83 84 85 86 87
9-16 88 89 8a 8b 90 91 92 93
17-24 94 95 96 97 98 99 9a 9b
25-32 80 80 80 80 80 80 80 80
1 6 1- 8 ac bc a0 a0 a0 a0 a0 a0
9-16 a0 a0 a0 a0 a0 a0 a0 a0
17-24 a0 a0 a0 a0 a0 a0 a0 a0
25-32 a0 a0 a0 a0 a0 a0 a0 a0
1 7 1- 8 cc dc c0 c0 c0 c0 c0 c0
9-16 c0 c0 c0 c0 c0 c0 c0 c0
17-24 c0 c0 c0 c0 c0 c0 c0 c0
25-32 c0 c0 c0 c0 c0 c0 c0 c0
1 8 1- 8 e0 e1 e2 e3 e4 e5 e6 e7
9-16 e8 e9 ea eb f0 f1 f2 f3
17-24 f4 f5 f6 f7 f8 f9 fa fb
25-32 1a0 1a0 1a0 1a0 1a0 1a0 1a0 1a0
1 15 1- 8 1cc 1dc 1c0 1c0 1c0 1c0 1c0 1c0
9-16 1c0 1c0 1c0 1c0 1c0 1c0 1c0 1c0
17-24 1c0 1c0 1c0 1c0 1c0 1c0 1c0 1c0
25-32 1c0 1c0 1c0 1c0 1c0 1c0 1c0 1c0
1 16 1- 8 1e0 1e1 1e2 1e3 1e4 1e5 1e6 1e7
9-16 1e8 1e9 1ea 1eb 1f0 1f1 1f2 1f3
17-24 1f4 1f5 1f6 1f7 1f8 1f9 1fa 1fb
25-32 1e0 1e0 1e0 1e0 1e0 1e0 1e0 1e0
--- --- ----- --- --- --- --- --- --- --- ---
2 1 1- 8 c 1c 0 0 0 0 0 0
9-16 0 0 0 0 0 0 0 0
17-24 0 0 0 0 0 0 0 0
25-32 0 0 0 0 0 0 0 0
2 2 1- 8 20 21 22 23 24 25 26 27
9-16 28 29 2a 2b 30 31 32 33
17-24 34 35 36 37 38 39 3a 3b
25-32 20 20 20 20 20 20 20 20
2 3 1- 8 57 41 42 43 44 45 50 51
9-16 52 53 54 55 40 40 40 40
17-24 40 40 40 40 40 40 40 40
OmniSwitch Troubleshooting Guide September 2005
page -117
Download from Www.Somanuals.com. All Manuals Search And Download.
25-32 40 40 40 40 40 40 40 40
2 4 1- 8 6c 7c 60 60 60 60 60 60
9-16 60 60 60 60 60 60 60 60
17-24 60 60 60 60 60 60 60 60
25-32 60 60 60 60 60 60 60 60
2 5 1- 8 80 81 82 83 84 85 86 87
9-16 88 89 8a 8b 90 91 92 93
17-24 94 95 96 97 98 99 9a 9b
25-32 80 80 80 80 80 80 80 80
2 6 1- 8 ac bc a0 a0 a0 a0 a0 a0
9-16 a0 a0 a0 a0 a0 a0 a0 a0
17-24 a0 a0 a0 a0 a0 a0 a0 a0
25-32 a0 a0 a0 a0 a0 a0 a0 a0
2 7 1- 8 cc dc c0 c0 c0 c0 c0 c0
9-16 c0 c0 c0 c0 c0 c0 c0 c0
17-24 c0 c0 c0 c0 c0 c0 c0 c0
25-32 c0 c0 c0 c0 c0 c0 c0 c0
2 8 1- 8 e0 e1 e2 e3 e4 e5 e6 e7
9-16 e8 e9 ea eb f0 f1 f2 f3
17-24 f4 f5 f6 f7 f8 f9 fa fb
25-32 e0 e0 e0 e0 e0 e0 e0 e0
2 9 1- 8 10c 11c 100 100 100 100 100 100
9-16 100 100 100 100 100 100 100 100
17-24 100 100 100 100 100 100 100 100
25-32 100 100 100 100 100 100 100 100
2 10 1- 8 120 121 122 123 124 125 126 127
9-16 128 129 12a 12b 130 131 132 133
17-24 134 135 136 137 138 139 13a 13b
25-32 120 120 120 120 120 120 120 120
2 11 1- 8 14c 15c 140 140 140 140 140 140
9-16 140 140 140 140 140 140 140 140
17-24 140 140 140 140 140 140 140 140
25-32 140 140 140 140 140 140 140 140
2 12 1- 8 16c 17c 160 160 160 160 160 160
9-16 160 160 160 160 160 160 160 160
17-24 160 160 160 160 160 160 160 160
25-32 160 160 160 160 160 160 160 160
2 13 1- 8 18c 19c 180 180 180 180 180 180
9-16 180 180 180 180 180 180 180 180
17-24 180 180 180 180 180 180 180 180
25-32 180 180 180 180 180 180 180 180
2 14 1- 8 1a0 1a1 1a2 1a3 1a4 1a5 1a6 1a7
9-16 1a8 1a9 1aa 1ab 1b0 1b1 1b2 1b3
17-24 1b4 1b5 1b6 1b7 1b8 1b9 1ba 1bb
25-32 1a0 1a0 1a0 1a0 1a0 1a0 1a0 1a0
2 15 1- 8 1cc 1dc 1c0 1c0 1c0 1c0 1c0 1c0
9-16 1c0 1c0 1c0 1c0 1c0 1c0 1c0 1c0
17-24 1c0 1c0 1c0 1c0 1c0 1c0 1c0 1c0
25-32 1c0 1c0 1c0 1c0 1c0 1c0 1c0 1c0
2 16 1- 8 1e0 1e1 1e2 1e3 1e4 1e5 1e6 1e7
9-16 1e8 1e9 1ea 1eb 1f0 1f1 1f2 1f3
17-24 1f4 1f5 1f6 1f7 1f8 1f9 1fa 1fb
25-32 1e0 1e0 1e0 1e0 1e0 1e0 1e0 1e0
--- --- ----- --- --- --- --- --- --- --- ---
3 1 1- 8 c 1c 0 0 0 0 0 0
9-16 0 0 0 0 0 0 0 0
17-24 0 0 0 0 0 0 0 0
25-32 0 0 0 0 0 0 0 0
3 2 1- 8 20 21 22 23 24 25 26 27
page -118
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
9-16 28 29 2a 2b 30 31 32 33
17-24 34 35 36 37 38 39 3a 3b
25-32 20 20 20 20 20 20 20 20
3 3 1- 8 57 41 42 43 44 45 50 51
9-16 52 53 54 55 40 40 40 40
17-24 40 40 40 40 40 40 40 40
25-32 40 40 40 40 40 40 40 40
3 4 1- 8 6c 7c 60 60 60 60 60 60
9-16 60 60 60 60 60 60 60 60
17-24 60 60 60 60 60 60 60 60
25-32 60 60 60 60 60 60 60 60
3 5 1- 8 80 81 82 83 84 85 86 87
9-16 88 89 8a 8b 90 91 92 93
17-24 94 95 96 97 98 99 9a 9b
25-32 80 80 80 80 80 80 80 80
3 6 1- 8 ac bc a0 a0 a0 a0 a0 a0
9-16 a0 a0 a0 a0 a0 a0 a0 a0
17-24 a0 a0 a0 a0 a0 a0 a0 a0
25-32 a0 a0 a0 a0 a0 a0 a0 a0
3 7 1- 8 cc dc c0 c0 c0 c0 c0 c0
9-16 c0 c0 c0 c0 c0 c0 c0 c0
17-24 c0 c0 c0 c0 c0 c0 c0 c0
Release History
Release 5.1; command was introduced.
Related Commands
Displays the overall status of all the fabric ASICs.
Displays the fabric ASIC statistics.
OmniSwitch Troubleshooting Guide September 2005
page -119
Download from Www.Somanuals.com. All Manuals Search And Download.
debug slb help
Prints a list of all debug Server Load Balancing (SLB) options.
debug slb help
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• Server Load Balancing (SLB) is not supported on OS-6600 series of switches.
• Not all the commands by the help option are implemented right now.
Examples
-> debug slb help
Command Name
Parameters
--------------------------------------------------------------
AdminStatus
<status=0|1>
CreateCluster
DeleteCluster
ClusterAdminStatus
ClusterDistribution
ClusterPingPeriod
ClusterPingTimeout
ClusterPingRetries
ClusterStickytime
Server
<name> <ipaddress>
<name>
<name> <status=0|1>
<name> <distrib=1|2>
<name> <seconds>
<name> <milliseconds>
<name> <retries>
<name> <seconds>
<name> <ipaddr> <status=0|1> <weight>
<name> <ipaddr>
RemoveServer
DumpCluster
<clusterid>
DumpClusters
DumpServer
<clusterid> <serverid>
DumpServers
DumpNI
DumpVlan
DumpMisc
DiscoveryPeriod
DiscoveryTimeout
DiscoveryRetries
StatPeriod
<milliseconds>
<milliseconds>
<number>
<milliseconds>
DeadlineWindow
Link
<milliseconds>
<port number> <adm-0|1> [<lnk-0|1>]
ResetCMM
ResetNI
<slot> <slice>
page -120
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
CMMTrace
NITrace
NIDebug
Flags
<level>
<level>
<slot> <slice>
Traps
<enable=0|1>
SimServers
ServerArp
PacketLoss
Kill
<enable=0|1>
<clusterid> <serverid> <macaddr> <port>
<percentage>
NI
<slot> <slice> <status=0|1>
<resetni=0|1>
Snapshot
Certify
Takeover
Help
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -121
Download from Www.Somanuals.com. All Manuals Search And Download.
debug http sessiondb
Displays the HTTP session database.
debug http sessiondb
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug http sessiondb
Sess
SessName
Name TimeOut
Status
URL Name--&--StatMsg
---+----+-------------+---------+-------+---------------+--------------------------
-------
Current Active WebView Session: 0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -122
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre warn
Enables and disables the Hardware Routing Engine (HRE) warning messages on a specific HRE.
debug hre warn {enable | disable} slot/slice
Syntax Definitions
enable
disable
slot
Enables warning messages.
Disables warning messages.
Specifies an NI slot number.
Specifies an NI slice (ASIC) number.
slice
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre warn enable 8/0
Release History
Release 5.1; command was introduced.
Related Commands
Enables and disables Hardware Routing Engine (HRE) trace mes-
sages on a specific HRE.
OmniSwitch Troubleshooting Guide September 2005
page -123
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre trace
Enables and disables Hardware Routing Engine (HRE) trace messages on a specific HRE.
debug hre trace {enable | disable} slot/slice
Syntax Definitions
enable
disable
slot
Enables trace messages.
Disables trace messages.
Specifies an NI slot number.
Specifies an NI slice (ASIC) number.
slice
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre trace enable 3/0
Release History
Release 5.1; command was introduced.
Related Commands
Enables and disables the Hardware Routing Engine (HRE) warning
messages on a specific HRE.
page -124
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre pcam
Displays all the PCAM entries known on a particular slot and slice.
debug hre pcam slot/slice
There are two possible arguments to this command - <start> and <count>. <start> is the PCAM index to
start with; default is 0. <count> is the number of entries to display; max is 24, default is 12.
Syntax Definitions
slot
Specifies an NI slot number.
slice
start
count
Specifies an NI slice (ASIC) number.
The PCAM index to start with.
The number of entries to display. The range is 0–24.
Defaults
parameter
default
start
0
count
12
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre pcam 11/0
*00005: e0000005 00000000 00000000 4c280000
[ip] dst=224.0.0.5
restart[mode=5], dakey=0000
*00012: e0000012 00000001 00000000 4c280000
[ip] dst=224.0.0.18
restart[mode=5], dakey=0001
0c000: 003d0001 c0a83d02 fff9015c 0c000000
[ipms] src=192.168.61.2, dakey=0001, sgid=03d, svpn=015c
forward[hdr=fff9]
0c001: 003c0001 c0a83c02 fff6015c 0c000000
[ipms] src=192.168.60.2, dakey=0001, sgid=03c, svpn=015c
forward[hdr=fff6]
0c002: 003b0001 c0a83b02 fff5015c 0c000000
[ipms] src=192.168.59.2, dakey=0001, sgid=03b, svpn=015c
OmniSwitch Troubleshooting Guide September 2005
page -125
Download from Www.Somanuals.com. All Manuals Search And Download.
forward[hdr=fff5]
0c003: 003a0001 c0a83a02 fff2015c 1c00c008
[ipms] src=192.168.58.2, dakey=0001, sgid=03a, svpn=015c
forward[hdr=fff2], next=0c008
0c004: 00390001 c0a83902 fff1015c 1c00c000
[ipms] src=192.168.57.2, dakey=0001, sgid=039, svpn=015c
forward[hdr=fff1], next=0c000
0c005: 00380001 c0a83802 fff0015c 1c00c001
[ipms] src=192.168.56.2, dakey=0001, sgid=038, svpn=015c
forward[hdr=fff0], next=0c001
0c006: 003e0000 c0a83e02 ffef015c 0c000000
[ipms] src=192.168.62.2, dakey=0000, sgid=03e, svpn=015c
forward[hdr=ffef]
0c007: 003d0000 c0a83d02 ffee015c 0c000000
[ipms] src=192.168.61.2, dakey=0000, sgid=03d, svpn=015c
forward[hdr=ffee]
0c008: 003e0001 c0a83e02 ffe9015c 0c000000
[ipms] src=192.168.62.2, dakey=0001, sgid=03e, svpn=015c
forward[hdr=ffe9]
0c009: 003c0000 c0a83c02 ffec015c 0c000000
[ipms] src=192.168.60.2, dakey=0000, sgid=03c, svpn=015c
forward[hdr=ffec]
Release History
Release 5.1; command was introduced.
Related Commands
Displays all the PCAM entries known on a particular slot and slice.
page -126
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre pcam verbose
Displays all the PCAM entries known on a particular slot and slice.
debug hre pcam verbose slot/slice [start count]
Syntax Definitions
slot
Specifies an NI slot number.
slice
start
count
Specifies an NI slice (ASIC) number.
The PCAM index to start with.
The number of entries to display. The range is 0–24.
Defaults
parameter
default
start
0
count
12
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre pcam verbose 11/0
*00005: e0000005 00000000 00000000 4c280000
[ip] dst=224.0.0.5
restart[mode=5], dakey=0000
mode=0, alloc=hash, collisions=0001
agetype=branch, child=0c006
*00012: e0000012 00000001 00000000 4c280000
[ip] dst=224.0.0.18
restart[mode=5], dakey=0001
mode=0, alloc=hash, collisions=0001
agetype=branch, child=0c008
0c000: 003d0001 c0a83d02 fff9015c 0c000000
[ipms] src=192.168.61.2, dakey=0001, sgid=03d, svpn=015c
forward[hdr=fff9]
mode=5, alloc=collision, prev=0c004
agetype=leaf, current=4, base=4, initial=2, parent=00012
siblingprev=0c008, siblingnext=0c001
0c001: 003c0001 c0a83c02 fff6015c 0c000000
OmniSwitch Troubleshooting Guide September 2005
page -127
Download from Www.Somanuals.com. All Manuals Search And Download.
[ipms] src=192.168.60.2, dakey=0001, sgid=03c, svpn=015c
forward[hdr=fff6]
mode=5, alloc=collision, prev=0c005
agetype=leaf, current=4, base=4, initial=2, parent=00012
siblingprev=0c000, siblingnext=0c002
0c002: 003b0001 c0a83b02 fff5015c 0c000000
[ipms] src=192.168.59.2, dakey=0001, sgid=03b, svpn=015c
forward[hdr=fff5]
mode=5, alloc=collision, prev=0c00d
agetype=leaf, current=4, base=4, initial=2, parent=00012
siblingprev=0c001, siblingnext=0c003
0c003: 003a0001 c0a83a02 fff2015c 1c00c008
[ipms] src=192.168.58.2, dakey=0001, sgid=03a, svpn=015c
forward[hdr=fff2], next=0c008
mode=5, alloc=collision, prev=0c00e
agetype=leaf, current=4, base=4, initial=2, parent=00012
siblingprev=0c002, siblingnext=0c004
Release History
Release 5.1; command was introduced.
Related Commands
Displays all the PCAM entries known on a particular slot and slice.
page -128
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre pcam mode range
This command displays the range of PCAM indices assigned to each mode.
debug hre pcam mode range slot/slice
Syntax Definitions
slot
Specifies an NI slot number.
slice
Specifies an NI slice (ASIC) number.
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre pcam mode range 11/0
mode 0: 00000 -> 03fff
mode 1: 04000 -> 07fff
mode 2: 08000 -> 0bfff
mode 3: 0c000 -> 0ffff
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -129
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre history
Displays the history of the Hardware Routing Engine (HRE).
debug hre history slot/slice
Syntax Definitions
slot
Specifies an NI slot number.
slice
Specifies an NI slice (ASIC) number.
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre history 11/0
IP flush all count = 0
IP flush net count = 886
last net = 0a286c04, last mask = ffffffff
last time = 140 seconds ago by 15
ARP flush count = 514
last next hop ip address = 0a286c04
last time = 140 seconds ago by 15
IPMS flush all count = 1
last time = 12826 seconds ago by 17
IPX flush all count = 1
last time = 12823 seconds ago by 16
IPX flush net count = 0
Aging period is 30 seconds
0 PCAM entries created, 0 entries aged in last cycle
Release History
Release 5.1; command was introduced.
page -130
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -131
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre error
Enables/Disables error messages from Hardware Routing Engine (HRE) support software on a Chassis
Management Module (CMM) for a specific slot/slice.
debug hre error {enable | disable} slot/slice
Syntax Definitions
enable
disable
slot
Enables error messages.
Disables error messages.
Specifies an NI slot number.
Specifies an NI slice (ASIC) number.
slice
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre error enable 3/0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -132
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre debug
Enables/Disables debug messages from Hardware Routing Engine (HRE) support software on a Chassis
Management Module (CMM) for a specific slot/slice.
debug hre debug {enable | disable} slot/slice
Syntax Definitions
enable
disable
slot
Enables debug messages.
Disables debug messages.
Specifies an NI slot number.
Specifies an NI slice (ASIC) number.
slice
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre debug enable 3/0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -133
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre cmm warn
Enables/Disables warning messages from Hardware Routing Engine (HRE) support software on a Chassis
Management Module (CMM).
debug hre cmm warn {enable | disable}
Syntax Definitions
enable
disable
Enables warning messages.
Disables warning messages.
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre cmm warn enable 3/0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -134
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre cmm trace
Enables/Disables trace messages from Hardware Routing Engine (HRE) support software on a Chassis
Management Module (CMM).
debug hre cmm trace {enable | disable}
Syntax Definitions
enable
disable
Enables warning messages.
Disables warning messages.
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre cmm trace enable 3/0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -135
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre cmm error
Enables/Disables error messages from Hardware Routing Engine (HRE) support software on a Chassis
Management Module (CMM).
debug hre cmm error {enable | disable}
Syntax Definitions
enable
disable
Enables warning messages.
Disables warning messages.
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre cmm error enable 3/0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -136
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug hre cmm debug
Enables/Disables debug messages from Hardware Routing Engine (HRE) support software on a Chassis
Management Module (CMM).
debug hre cmm debug {enable | disable}
Syntax Definitions
enable
disable
Enables warning messages.
Disables warning messages.
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-66000 series does not have a HRE so this commands is not supported on these switches.
Examples
-> debug hre cmm debug enable 3/0
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -137
Download from Www.Somanuals.com. All Manuals Search And Download.
debug health
Enables and disables health debugging.
debug health {enable | disable}
Syntax Definitions
enable
disable
Enables health debugging.
Disables health debugging.
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug health enable
Release History
Release 5.1; command was introduced.
Related Commands
Displays the history of CPU utilization on a Chassis Management
Module (CMM) if no parameters are specified and displays the his-
tory of the CPU’s health if parameters are specified.
page -138
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug health cpu
Displays the history of CPU utilization on a Chassis Management Module (CMM) if no parameters are
specified and displays the history of the CPU’s health if parameters are specified.
debug health cpu [slot]
Syntax Definitions
slot
Specifies an interface slot number.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
If no parameters are specified:
-> debug health cpu
Device Level Cpu Utilization
SECONDS: [4]8 [5]15 [6]4 [7]14 [8]4 [9]16 [10]3 [11]15 [0]4 [1]18 [2]5
[3]23
MINUTES: [2]10 [3]10 [4]9 [5]11 [6]10 [7]10 [8]10 [9]10 [10]10 [11]10
[12]11 [13]10 [14]9 [15]10 [16]9 [17]10 [18]10 [19]9 [20]9
[21]10 [22]9 [23]10 [24]9 [25]9 [26]11 [27]10 [28]9 [29]10
[30]10 [31]11 [32]10 [33]9 [34]10 [35]9 [36]10 [37]10 [38]10
[39]11 [40]10 [41]10 [42]12 [43]10 [44]10 [45]10 [46]9 [47]11
[48]11 [49]9 [50]11 [51]9 [52]11 [53]10 [54]10 [55]10 [56]10
[57]10 [58]11 [59]11 [0]10 [1]10
sec<23> min<10> hrAvg<9> hrMax<12>
If a slot number is specified:
-> debug health cpu 11
Slot 11 Cpu Utilization
SECONDS: [11]19 [0]26 [1]17 [2]18 [3]17 [4]15 [5]17 [6]17 [7]19 [8]18
[9]19 [10]21
MINUTES: [59]18 [0]18 [1]19 [2]17 [3]18 [4]19 [5]18 [6]18 [7]17 [8]19
[9]17 [10]18 [11]18 [12]17 [13]18 [14]18 [15]20 [16]18 [17]18
[18]19 [19]19 [20]18 [21]17 [22]19 [23]18 [24]18 [25]19 [26]18
[27]19 [28]17 [29]18 [30]18 [31]19 [32]19 [33]18 [34]19 [35]17
[36]19 [37]18 [38]18 [39]19 [40]19 [41]18 [42]17 [43]18 [44]18
[45]18 [46]18 [47]18 [48]19 [49]18 [50]18 [51]19 [52]17 [53]19
[54]19 [55]19 [56]18 [57]18 [58]19
sec<21> min<18> hrAvg<18> hrMax<20>
OmniSwitch Troubleshooting Guide September 2005
page -139
Download from Www.Somanuals.com. All Manuals Search And Download.
Release History
Release 5.1; command was introduced.
Related Commands
Enables and disables health debugging.
page -140
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug health rx
Displays health of receive utilization on a particular slot or slot/port.
debug health rx [slot[/port]]
Syntax Definitions
slot
Specifies an interface slot number.
Specifies an interface port number.
port
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
A slot number is specified:
-> debug health rx 2
Slot 2 Input Utilization
SECONDS: [1]0 [2]0 [3]0 [4]0 [5]0 [6]0 [7]0 [8]0 [9]0 [10]0 [11]0 [0]0
MINUTES: [36]0 [37]0 [38]0 [39]0 [40]0 [41]0 [42]0 [43]0 [44]0 [45]0
[46]0 [47]0 [48]0 [49]0 [50]0 [51]0 [52]0 [53]0 [54]0 [55]0
[56]0 [57]0 [58]0 [59]0 [0]0 [1]0 [2]0 [3]0 [4]0 [5]0 [6]0 [7]0
[8]0 [9]0 [10]0 [11]0 [12]0 [13]0 [14]0 [15]0 [16]0 [17]0 [18]0
[19]0 [20]0 [21]0 [22]0 [23]0 [24]0 [25]0 [26]0 [27]0 [28]0
[29]0 [30]0 [31]0 [32]0 [33]0 [34]0 [35]0
sec<0> min<0> hrAvg<0> hrMax<0>
A slot and port number is specified:
-> debug health rx 2/1
Port 2/1 Input Utilization
SECONDS:
MINUTES:
sec<0> min<0> hrAvg<0> hrMax<0>
Release History
Release 5.1; command was introduced.
OmniSwitch Troubleshooting Guide September 2005
page -141
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
N/A
page -142
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug health memory
Displays history of memory utilization on CMM when no slot number is specified and displays history of
memory utilization on a particular slot if a slot number is specified.
debug health memory [slot]
Syntax Definitions
slot
Specifies an interface slot number.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
No slot number is specified:
-> debug health memory
Device Level Memory Utilization
SECONDS: [10]46 [11]46 [0]46 [1]46 [2]46 [3]46 [4]46 [5]46 [6]46 [7]46
[8]46 [9]46
MINUTES: [1]46 [2]46 [3]46 [4]46 [5]46 [6]46 [7]46 [8]46 [9]46 [10]46
[11]46 [12]46 [13]46 [14]46 [15]46 [16]46 [17]46 [18]46 [19]46
[20]46 [21]46 [22]46 [23]46 [24]46 [25]46 [26]46 [27]46 [28]46
[29]46 [30]46 [31]46 [32]46 [33]46 [34]46 [35]46 [36]46 [37]46
[38]46 [39]46 [40]46 [41]46 [42]46 [43]46 [44]46 [45]46 [46]46
[47]46 [48]46 [49]46 [50]46 [51]46 [52]46 [53]46 [54]46 [55]46
[56]46 [57]46 [58]46 [59]46 [0]46
sec<46> min<46> hrAvg<46> hrMax<46>
A slot number is specified:
-> debug health memory 11
Slot 11 Memory Utilization
SECONDS: [2]43 [3]43 [4]43 [5]43 [6]43 [7]43 [8]43 [9]43 [10]43 [11]43
[0]43 [1]43
MINUTES: [2]43 [3]43 [4]43 [5]43 [6]43 [7]43 [8]43 [9]43 [10]43 [11]43
[12]43 [13]43 [14]43 [15]43 [16]43 [17]43 [18]43 [19]43 [20]43
[21]43 [22]43 [23]43 [24]43 [25]43 [26]43 [27]43 [28]43 [29]43
[30]43 [31]43 [32]43 [33]43 [34]43 [35]43 [36]43 [37]43 [38]43
[39]43 [40]43 [41]43 [42]43 [43]43 [44]43 [45]43 [46]43 [47]43
[48]43 [49]43 [50]43 [51]43 [52]43 [53]43 [54]43 [55]43 [56]43
[57]43 [58]43 [59]43 [0]43 [1]43
sec<43> min<43> hrAvg<43> hrMax<43>
OmniSwitch Troubleshooting Guide September 2005
page -143
Download from Www.Somanuals.com. All Manuals Search And Download.
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -144
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug gmap flags
Displays the GMAP flags and information about GMAP entries in GMAP database.
debug gmap flags
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug gmap flags
GMAP Holdtime Interval (minutes)
GMAP Updatetime Interval (seconds)
= 4320,
= 300,
GMAP Gaptime
Interval (milliseconds) = 133
MAC Address Protocol VLAN Src Switch ID Timeout(sec)
--------------+---------+------+--------------+------------
0010A4:B5B538
10806
111 00D095:7962AA 00:00:00:00
252288
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -145
Download from Www.Somanuals.com. All Manuals Search And Download.
debug console flow control
Enables and disables the flow control for the console.
debug console flow control {enable | disable}
Syntax Definitions
enable
disable
Enables flow control.
Disables flow control.
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug console flow control enable
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -146
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug console show flow control
Displays the current flow control status.
debug console show flow control
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug console show flow control
Flow Control: Enabled
Output fields are described below:
output definitions
Flow Control
The current flow control status, which can be Enabled or Disabled.
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -147
Download from Www.Somanuals.com. All Manuals Search And Download.
debug command-info
Enables and disables the command-info mode.
debug command-info {enable | disable}
Syntax Definitions
enable
disable
Enables command-info mode.
Disables command-info mode.
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug command-info enable
CLI command info mode on
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -148
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug clishell data
Displays the current information about the session.
debug clishell data
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug clishell data
Session Id
EUPM User
: 3
: 0
CLI oper mode : 0
Def sub-parser : 12
I/O ctrl option : 14
Command prefix :
MIP appOut
: 71578880
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -149
Download from Www.Somanuals.com. All Manuals Search And Download.
debug amap database
Verifies if the AMAP database is fine or not.
debug amap database
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug amap database
AMAP Debug database ok
Output fields are described below:
output definitions
AMAP Debug database
The current status of the AMAP database.
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -150
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug chassis show
Displays all the debug configurations.
debug chassis show
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug chassis show
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -151
Download from Www.Somanuals.com. All Manuals Search And Download.
debug chassis secondary emp
Enables and disables the Ethernet Management Port (EMP) port on a secondary Chassis Management
Module (CMM)
debug chassis secondary emp {enable | disable}
Syntax Definitions
enable
disable
Enables the secondary CMM’s EMP port.
Disables the secondary CMM’s EMP port.
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
OS-6600 series does not have an EMP port.
Examples
-> debug chassis secondary emp enable
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -152
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug chassis hello
Enables and disables hello messages from the secondary Chassis Management Module (CMM) to the
primary CMM.
debug chassis hello {enable | disable}
Syntax Definitions
enable
disable
Enables hello messages.
Disables hello messages.
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug chassis hello disable
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -153
Download from Www.Somanuals.com. All Manuals Search And Download.
debug chassis hello timers
Enables and disables hello timers from the primary Chassis Management Module (CMM) to the second-
ary. If the secondary CMM does not respond back in the interval, it is rebooted.
debug chassis hello timers {enable | disable}
Syntax Definitions
enable
disable
Enables hello timers.
Disables hello timers.
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug chassis hello timers disable
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -154
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug chassis auto-reboot
Enables and disables chassis auto-reboots after a fatal error.
debug chassis auto-reboot {enable | disable | on | off}
Syntax Definitions
enable
disable
on
Enables chassis auto-reboots after a fatal error.
Disables chassis auto-reboots after a fatal error.
Same as enable.
off
Same as disable.
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug chassis auto-reboot enable
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -155
Download from Www.Somanuals.com. All Manuals Search And Download.
debug chassis auto-reboot ni
Enables and disables Network Interface (NI) module auto-reboots after a fatal error.
debug chassis auto-reboot ni {enable | disable}
Syntax Definitions
enable
disable
Enables NI auto-reboots after a fatal error.
Disables NI auto-reboots after a fatal error.
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug chassis auto-reboot ni enable
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -156
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug vlan vpas
Displays the information about all the ports with their IfIndex and the VLAN membership.
debug vlan vpas
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug vlan vpas
port vlan
type
status
------+-------+---------+-------------
1001
1
default forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
default forwarding
qtagged forwarding
qtagged forwarding
1001 140
1001 141
1001 150
1001 511
1002
1002 100
1002 150
1
2001
1
default
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
default
qtagged
qtagged
default
default
default
default
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
2001 100
2001 102
2001 103
2001 104
2001 114
2001 115
2001 116
2001 130
2001 311
2001 411
2001 611
2001 711
2002
2002 111
2002 150
2003
2004
2005
2006
1
1
1
1
1
OmniSwitch Troubleshooting Guide September 2005
page -157
Download from Www.Somanuals.com. All Manuals Search And Download.
2006 105
2006 108
2006 110
2006 111
2006 112
2006 117
2006 150
2006 211
2006 212
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
default
qtagged
qtagged
qtagged
default
default
default
default
qtagged
qtagged
default
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
default
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
2007
2007
1
62
2007 150
2007 211
2008
2009
2010
2011
1
62
1
1
2011 150
2011 211
2012
2012
2012
2012
2012
2012
2012
2012
2012
2012
2012
2012
2012
2012
1
50
51
52
53
54
55
56
57
58
59
60
61
62
2012 100
2012 102
2012 103
2012 104
2012 105
2012 106
2012 107
2012 108
2012 109
2012 110
2012 111
2012 112
2012 114
2012 115
2012 116
2012 117
2012 130
2012 140
2012 141
2012 150
2012 211
2012 212
2012 311
2012 511
2012 711
4001
1
page -158
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
4001 104
4001 150
qtagged
qtagged
inactive
inactive
4002
4002 105
4002 150
6001
6001 108
6001 150
1
default forwarding
qtagged forwarding
qtagged forwarding
default forwarding
qtagged forwarding
qtagged forwarding
1
6002
6002 109
6002 150
1
default
qtagged
qtagged
inactive
inactive
inactive
7001
7001 110
7001 150
1
default forwarding
qtagged forwarding
qtagged forwarding
7002
1
default
qtagged
qtagged
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
qtagged
qtagged
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
7002 111
7002 150
8001 611
8002 140
8003 140
8004 140
8005 140
8006 140
8007 140
8008 140
8009 140
8010 140
8011 140
8012 140
8013 140
8014 140
8015 140
8016 140
8017 140
8018 140
8019 140
8020 140
8021 140
8022 140
8023 114
8024 140
9001
9001 150
9001 211
1
9002
9002 112
9002 150
1
default forwarding
qtagged forwarding
qtagged forwarding
10001
10001 150
10001 212
10002
10002 114
10002 150
1
default
qtagged
qtagged
default
qtagged
qtagged
inactive
inactive
inactive
inactive
inactive
inactive
1
11001
11002
12001
12002
13001
13002
1
1
1
1
1
1
default forwarding
default forwarding
default
default
default
default
inactive
inactive
inactive
inactive
OmniSwitch Troubleshooting Guide September 2005
page -159
Download from Www.Somanuals.com. All Manuals Search And Download.
13003
13004
13005
13006
13007
13008
13009
13010
13011
13012
13013
13014
13015
13016
13017
13018
13019
13020
13021
13022
13023
13024
14001
14001 117
14001 150
14002
14002 130
14002 150
16001
16002
16003
16004
16005
16006
16007
16008
16009
16010
16011
16012
16013
16014
16015
16016
16017
16018
16019
16020
16021
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
qtagged
qtagged
default
qtagged
qtagged
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
default
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
16022
16023
16024
40000001
40000001
40000001
40000001
40000001
40000001
40000001
1
50
51
52
53
54
55
default forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
page -160
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
40000001
40000001
40000001
40000001
40000001
40000001
40000001
40000002
40000002
40000002
40000002
40000002
40000002
40000002
40000002
40000002
40000002
40000002
40000002
40000002
40000002
56
57
58
59
60
61
62
1
50
51
52
53
54
55
56
57
58
59
60
61
62
qtagged forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
qtagged forwarding
default
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
qtagged
blocking
blocking
blocking
blocking
blocking
blocking
blocking
blocking
blocking
blocking
blocking
blocking
blocking
blocking
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -161
Download from Www.Somanuals.com. All Manuals Search And Download.
debug vlan rule protocol-map
Displays the protocol map available. If a proprietary protocol type is configured on the switch that will
also display in the output of this command.
debug vlan rule protocol-map
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug vlan rule protocol-map
*** Protocol Indicator Map ***
proto = Ethernet II IP
proto = Ethernet II ARP
proto = Ethernet II RARP
Frame = E-II PI = 0
Frame = E-II PI = 0
Frame = E-II PI = 0
proto = SNAP IP
proto = SNAP ARP
proto = SNAP RARP
Frame = 802.3PI = 1
Frame = 802.3 PI = 1
Frame = 802.3 PI = 1
proto = IPX Ethernet II
proto = IPX Novell
Frame = E-II PI = 4
Frame = 802.3 PI = 3
proto = IPX LLC
proto = IPX SNAP
Frame = 802.3 PI = 2
Frame = 802.3 PI = 5
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -162
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug vlan rule ports
Displays all the ports available and can be a candidate for VLAN rules.
debug vlan rule ports
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
All the ports shown as “+” are in use. If a “+” appears under mobile column then it indicates that the port
has been configured as mobile port.
Examples
-> debug vlan rule ports
port candidate mobile
-----+-----------+---------
1/1
1/2
2/1
2/2
2/3
2/4
2/5
2/6
2/7
2/8
2/9
2/10
2/11
2/12
4/1
4/2
6/1
6/2
7/1
7/2
8/1
8/2
8/3
8/4
8/5
8/6
8/7
-
-
-
-
+
+
+
-
-
+
+
+
-
-
-
-
-
-
-
-
+
+
+
+
+
+
+
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
OmniSwitch Troubleshooting Guide September 2005
page -163
Download from Www.Somanuals.com. All Manuals Search And Download.
8/8
8/9
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
-
-
-
-
-
-
-
-
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
-
-
+
+
+
+
+
+
+
+
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
+
+
+
+
+
+
+
+
8/10
8/11
8/12
8/13
8/14
8/15
8/16
8/17
8/18
8/19
8/20
8/21
8/22
8/23
8/24
9/1
9/2
10/1
10/2
11/1
11/2
12/1
12/2
13/1
13/2
13/3
13/4
13/5
13/6
13/7
13/8
13/9
13/10
13/11
13/12
13/13
13/14
13/15
13/16
13/17
13/18
13/19
13/20
13/21
13/22
13/23
13/24
14/1
14/2
16/1
16/2
16/3
16/4
16/5
16/6
16/7
16/8
page -164
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
16/9
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
16/10
16/11
16/12
16/13
16/14
16/15
16/16
16/17
16/18
16/19
16/20
16/21
16/22
16/23
16/24
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -165
Download from Www.Somanuals.com. All Manuals Search And Download.
debug vlan rule database
Displays the rules configured on the switch for Group Mobility.
debug vlan rule database
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug vlan rule database
IP NETWORK RULES
B ssz=2 p=563bf88 l=563bf88 r=46fb4ac v=111
R ssz=1 p=46fb488 l=563bf88 r=563bf88 v=114
PORT RULES
B ssz=1 p=563bf88 l=563bf88 r=563bf88 v=103
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -166
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug vlan rule communication
Displays the communication of the Chassis Management Module (CMM) with all the software modules
and all Network Interface (NI) modules for synchronizing the rules configured on the CMM.
debug vlan rule communication
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• GlobSlice indicates the slot number.
• If an NI is not present in the chassis then the state will appear as dead.
• The state field should always be RX (received) or CFGD (configured) but should never be dead for
any module that exists in the NI. Dead will indicate that the module is not working properly.
Examples
-> debug vlan rule communication
VlnMgr skt=0x75
CSping skt=0x73
CfgMgr skt=0x74
CLI skt=0x74
rapp=8
rsnp=3
rsnp=6
rsnp=3
rsnp=67
rsnp=4
rsnp=2
rsnp=0
rsnp=3
rsnp=6
rsnp=1
rsnp=1
rsnp=3
rsnp=1
rsnp=3
CNXN-OR state:RX
CNXNLESS state:RX
CNXNLESS state:RX
CNXNLESS state:RX
CNXNLESS state:CFGD
CNXNLESS state:CFGD
CNXNLESS state:RX
CNXNLESS state:RX
CNXN-OR state:RX
CNXN-OR state:RX
CNXN-OR state:CFGD
CNXNLESS state:RX
CNXN-OR state:CFGD
CNXN-OR state:CFGD
rapp=64
rapp=66
rapp=67
rapp=68
rapp=69
rapp=65
rapp=64
rapp=19
rapp=81
rapp=10
rapp=70
SNMP skt=0x74
WbView skt=0x74
PrtMgr skt=0x76
CSniev skt=0x73
GMAP skt=0x77
PSM skt=0x78
SrcLrn skt=0x79
MpGate skt=0x74
AAA_AVLAN skt=0x7a
AAA_ONEX skt=0x7b
rapp=20
rapp=91
GlobSlice: 0 skt=0x130 rslot=1 rslice=0 rapp=9
state:RX
GlobSlice: 1 skt=0x130 rslot=2 rslice=0 rapp=9
state:RX
rsnp=2
rsnp=2
rsnp=0
rsnp=2
rsnp=0
CNXNLESS
CNXNLESS
CNXN-OR
CNXNLESS
CNXN-OR
GlobSlice: 2 skt=0x0
state:DEAD
rslot=0 rslice=0 rapp=0
GlobSlice: 3 skt=0x130 rslot=4 rslice=0 rapp=9
state:RX
GlobSlice: 4 skt=0x0
state:DEAD
rslot=0 rslice=0 rapp=0
OmniSwitch Troubleshooting Guide September 2005
page -167
Download from Www.Somanuals.com. All Manuals Search And Download.
GlobSlice: 5 skt=0x130 rslot=6 rslice=0 rapp=9
state:RX
GlobSlice: 6 skt=0x130 rslot=7 rslice=0 rapp=9
state:RX
GlobSlice: 7 skt=0x130 rslot=8 rslice=0 rapp=9
state:RX
GlobSlice: 8 skt=0x130 rslot=9 rslice=0 rapp=9
state:RX
GlobSlice: 9 skt=0x130 rslot=10 rslice=0 rapp=9
state:RX
GlobSlice:10 skt=0x130 rslot=11 rslice=0 rapp=9
state:RX
GlobSlice:11 skt=0x130 rslot=12 rslice=0 rapp=9
state:RX
GlobSlice:12 skt=0x130 rslot=13 rslice=0 rapp=9
state:RX
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=0
rsnp=2
CNXNLESS
CNXNLESS
CNXNLESS
CNXNLESS
CNXNLESS
CNXNLESS
CNXNLESS
CNXNLESS
CNXNLESS
CNXN-OR
GlobSlice:13 skt=0x130 rslot=14 rslice=0 rapp=9
state:RX
GlobSlice:14 skt=0x0
state:DEAD
rslot=0 rslice=0 rapp=0
GlobSlice:15 skt=0x130 rslot=16 rslice=0 rapp=9
state:RX
CNXNLESS
Release History
Release 5.1; command was introduced.
Related Commands
N/A
page -168
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug vlan communication
Displays the communication of the Chassis management Module (CMM) with all the software modules
and all Network Interface (NI) modules.
debug vlan communication
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• GlobSlice indicates the slot number.
• If an NI is not present in the chassis then the state will appear as dead.
Examples
-> debug vlan communication
***CMM Connections***
CS Ping sid= 1c rap= 64 rsp= 6
defaults assumed=1
txrty=0 txfail=0 bfrty=0
SL VPA sid= 26 rap= 10 rsp= 7
defaults assumed=0
CNXNLESS
CNXN-OR
NO-RX notify=0
NO-RX notify=0
txrty=0 txfail=0 bfrty=0
802.1Q sid= 1e rap= 7 rsp= 3
defaults assumed=1
txrty=0 txfail=0 bfrty=0
Port Mgr sid= 1f rap= 65 rsp= 0
defaults assumed=1
txrty=0 txfail=0 bfrty=0
SrcLrn sid= 25 rap= 10 rsp= 1
defaults assumed=0
txrty=0 txfail=0 bfrty=0
CS Ni Evt sid= 1c rap= 64 rsp= 3
defaults assumed=0
txrty=0 txfail=0 bfrty=0
CS Mac sid= 1c rap= 64 rsp= 11
defaults assumed=0
txrty=0 txfail=0 bfrty=0
Cfg Mgr sid= 1d rap= 66 rsp= 3
defaults assumed=1
CNXN-OR ESTABLISHED notify=5
CNXNLESS ESTABLISHED notify=0
CNXN-OR ESTABLISHED notify=5
CNXNLESS ESTABLISHED notify=0
CNXNLESS ESTABLISHED notify=0
CNXNLESS ESTABLISHED notify=0
CNXNLESS ESTABLISHED notify=0
txrty=0 txfail=0 bfrty=0
CLI sid= 1d rap= 67 rsp= 67
OmniSwitch Troubleshooting Guide September 2005
page -169
Download from Www.Somanuals.com. All Manuals Search And Download.
defaults assumed=0
txrty=0 txfail=0 bfrty=0
SNMP sid= 1d rap= 68 rsp= 4
defaults assumed=0
txrty=0 txfail=0 bfrty=0
Webview sid= 1d rap= 69 rsp= 2
defaults assumed=0
CNXNLESS
CNXNLESS
NO-RX notify=0
NO-RX notify=0
txrty=0 txfail=0 bfrty=0
IPMS MC sid= 27 rap= 17 rsp= 23
defaults assumed=0
CNXN-OR ESTABLISHED notify=0
txrty=0 txfail=0 bfrty=0
Regist sid= 36 rap= 68 rsp= 7
defaults assumed=1
CNXNLESS
NO-RX notify=0
txrty=0 txfail=0 bfrty=0
GrpMob sid= 2c rap= 9 rsp= 3
defaults assumed=0
txrty=0 txfail=0 bfrty=0
IP sid= 20 rap= 15 rsp= 7
defaults assumed=0
CNXN-OR ESTABLISHED notify=5
CNXN-OR ESTABLISHED notify=80
txrty=0 txfail=0 bfrty=0
DRC sid= 23 rap= 74 rsp= 1
defaults assumed=0
CNXN-OR
NO-RX notify=0
txrty=0 txfail=0 bfrty=0
SLB sid= 24 rap= 25 rsp= 1
defaults assumed=0
txrty=0 txfail=0 bfrty=0
IPX sid= 21 rap= 16 rsp= 10
defaults assumed=0
txrty=0 txfail=0 bfrty=0
UDP Rly sid= 22 rap= 22 rsp= 0
defaults assumed=0
txrty=0 txfail=0 bfrty=0
AAA sid= 28 rap= 20 rsp= 1
defaults assumed=0
CNXN-OR ESTABLISHED notify=16
CNXN-OR ESTABLISHED notify=32
CNXN-OR ESTABLISHED notify=1
CNXN-OR ESTABLISHED notify=0
txrty=0 txfail=0 bfrty=0
Nan Drvr sid= 29 rap= 78 rsp= 3
defaults assumed=0
CNXN-OR
NO-RX notify=0
txrty=0 txfail=0 bfrty=0
Span Tree sid= 2a rap= 11 rsp= 1
defaults assumed=1
txrty=0 txfail=0 bfrty=0
STP SVC sid= 2b rap= 11 rsp= 7
defaults assumed=1
txrty=0 txfail=0 bfrty=0
XMAP sid= 2d rap= 18 rsp= 5
defaults assumed=1
txrty=0 txfail=0 bfrty=0
GMAP sid= 2e rap= 19 rsp= 5
defaults assumed=1
txrty=0 txfail=0 bfrty=0
PSM sid= 2f rap= 81 rsp= 1
defaults assumed=1
txrty=0 txfail=0 bfrty=0
Mip Gtwy sid= 1d rap= 70 rsp= 3
defaults assumed=0
txrty=0 txfail=0 bfrty=0
VRRP sid= 30 rap= 77 rsp= 1
defaults assumed=0
CNXN-OR ESTABLISHED notify=7
CNXN-OR ESTABLISHED notify=0
CNXN-OR ESTABLISHED notify=0
CNXN-OR ESTABLISHED notify=0
CNXN-OR ESTABLISHED notify=0
CNXNLESS ESTABLISHED notify=0
CNXN-OR ESTABLISHED notify=16
txrty=0 txfail=0 bfrty=0
page -170
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
IPMS VL sid= 32 rap= 17 rsp= 34
defaults assumed=0
txrty=0 txfail=0 bfrty=0
QOS sid= 31 rap= 13 rsp= 2
defaults assumed=0
txrty=0 txfail=0 bfrty=0
Link Agg sid= 33 rap= 12 rsp= 1
defaults assumed=1
CNXN-OR ESTABLISHED notify=80
CNXN-OR ESTABLISHED notify=82
CNXN-OR ESTABLISHED notify=4
txrty=0 txfail=0 bfrty=0
Mirror sid= 34 rap= 23 rsp= 1
defaults assumed=1
CNXN-OR
NO-RX notify=0
txrty=0 txfail=0 bfrty=0
SNMP Agt sid= 35 rap= 68 rsp= 7
defaults assumed=0
CNXN-OR ESTABLISHED notify=8
txrty=0 txfail=0 bfrty=0
***NI Connections***
GlobSlice: 0 skt=0x131 rslot=1 rslice=0 rapp=8
rsnp=2
rsnp=2
rsnp=0
CNXNLESS state:RX
primary:YES nrCnxns:1 sync:3
GlobSlice: 1 skt=0x131 rslot=2 rslice=0 rapp=8
CNXNLESS state:RX
primary: NO nrCnxns:1 sync:3
GlobSlice: 2 skt=0x0 rslot=0 rslice=0 rapp=0
CNXN-OR state:DEAD primary: NO nrCnxns:0 sync:0
GlobSlice: 3 skt=0x131 rslot=4 rslice=0 rapp=8 rsnp=2
CNXNLESS state:RX primary: NO nrCnxns:1 sync:3
GlobSlice: 4 skt=0x0 rslot=0 rslice=0 rapp=0 rsnp=0
CNXN-OR state:DEAD primary: NO nrCnxns:0 sync:0
GlobSlice: 5 skt=0x131 rslot=6 rslice=0 rapp=8 rsnp=2
primary: NO nrCnxns:1 sync:3
CNXNLESS state:RX
GlobSlice: 6 skt=0x131 rslot=7 rslice=0 rapp=8
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=2
rsnp=0
CNXNLESS state:RX
primary: NO nrCnxns:1 sync:3
GlobSlice: 7 skt=0x131 rslot=8 rslice=0 rapp=8
CNXNLESS state:RX
primary: NO nrCnxns:1 sync:3
GlobSlice: 8 skt=0x131 rslot=9 rslice=0 rapp=8
CNXNLESS state:RX
primary: NO nrCnxns:1 sync:3
GlobSlice: 9 skt=0x131 rslot=10 rslice=0 rapp=8
CNXNLESS state:RX
primary: NO nrCnxns:1 sync:3
GlobSlice:10 skt=0x131 rslot=11 rslice=0 rapp=8
CNXNLESS state:RX
primary: NO nrCnxns:1 sync:3
GlobSlice:11 skt=0x131 rslot=12 rslice=0 rapp=8
CNXNLESS state:RX
primary: NO nrCnxns:1 sync:3
GlobSlice:12 skt=0x131 rslot=13 rslice=0 rapp=8
CNXNLESS state:RX
primary: NO nrCnxns:1 sync:3
GlobSlice:13 skt=0x131 rslot=14 rslice=0 rapp=8
CNXNLESS state:RX
GlobSlice:14 skt=0x0 rslot=0 rslice=0 rapp=0
CNXN-OR state:DEAD primary: NO nrCnxns:0 sync:0
GlobSlice:15 skt=0x131 rslot=16 rslice=0 rapp=8 rsnp=2
CNXNLESS state:RX primary: NO nrCnxns:1 sync:3
primary: NO nrCnxns:1 sync:3
Release History
Release 5.1; command was introduced.
OmniSwitch Troubleshooting Guide September 2005
page -171
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
N/A
page -172
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug port information
Displays all the information related to an interface. It includes the counters, mobile port configuration, tag,
aggregate, phy, LED, and MAC related information
debug port information slot/port
Syntax Definitions
slot
Specifies an interface slot number.
Specifies an interface port number.
port
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug port information 11/1
Release History
Release 5.1; command was introduced.
Related Commands
N/A
OmniSwitch Troubleshooting Guide September 2005
page -173
Download from Www.Somanuals.com. All Manuals Search And Download.
debug qos
Configures the type of QoS events that will be displayed in the QoS log.
debug qos [info] [config] [rule] [main] [route] [hre] [port] [msg] [sl] [ioctl] [mem] [cam] [mapper]
[flows] [queue] [slot] [l2] [l3] [classifier] [nat] [sem] [pm] [ingress] [egress] [rsvp] [balance] [nimsg]
debug no qos
debug no qos [info] [config] [rule] [main] [route] [hre] [port] [msg] [sl] [ioctl] [mem] [cam] [mapper]
[flows] [queue] [slot] [l2] [l3] [classifier] [nat] [sem] [pm] [ingress] [egress] [rsvp] [balance] [nimsg]
Syntax Definitions
flows
queue
rule
l2
Logs events for flows on the switch.
Logs events for queues created and destroyed on the switch.
Logs events for rules configured on the switch.
Logs Layer 2 QoS events on the switch.
l3
Logs Layer 3 QoS events on the switch.
nat
Logs events for Network Address Translation policies. Not supported
for the OmniSwitch 6624/6648.
port
Logs events related to QoS ports.
Logs QoS messages.
msg
classifier
Logs information whenever the switch classifies a flow; more details are
provided if the log level is higher.
info
Logs basic information about the switch
Logs information about the global configuration.
Logs information about basic program interfaces.
Logs information about routing.
config
main
route
hre
Logs information about hardware route programming.
Logs information about source learning.
Logs information about memory.
sl
mem
cam
Logs information about CAM operations.
Logs information about mapping queues.
Logs events related to slots.
mapper
slot
sem
Logs information about semaphore, process locking.
Logs events related to the Policy Manager.
Logs information about packets arriving on the switch.
pm
ingress
page -174
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
egress
rsvp
Logs information about packets leaving the switch.
Logs information about RSVP flows. Currently not supported.
balance
Logs information about flows that are part of a load balancing cluster.
Not supported for the OmniSwitch 6624/6648.
nimsg
Logs information about QoS interfaces.
Defaults
By default basic information messages are logged (info). Error messages are always logged.
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• Use this command to troubleshoot QoS events on the switch.
• Use the no form of the command to change the type of messages that will be logged or to return debug-
ging to its default state.
Examples
-> debug qos flows queue
-> qos debug no flows no queue
-> debug no qos
Release History
Release 5.1; command was introduced.
MIB Objects
alaQoSConfigTable
alaQoSConfigDebug
OmniSwitch Troubleshooting Guide September 2005
page -175
Download from Www.Somanuals.com. All Manuals Search And Download.
debug systrace
Enables or disables sysTrace logging. The system trace, or sysTrace, facility provides a consistent, high-
level mechanism for capturing event records in a history buffer. Captured sysTrace information can be
referenced for system debugging or following the unlikely event of a system crash. This trace facility will
generally be used by higher level applications.
debug systrace {enable | disable}
Syntax Definitions
enable
disable
Enables sysTrace logging.
Disables sysTrace logging.
Defaults
parameter
default
enable
enable | disable
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug systrace enable
-> debug systrace disable
Release History
Release 5.1; command was introduced.
page -176
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Enables or disables kTrace logging.
Adds or removes a kTrace capture level for a specified subsystem.
Displays current kTrace parameters.
Displays kTrace log information.
Enables or disables sysTrace log output to the console.
Adds or removes a sysTrace capture level for a specified subsystem.
Displays sysTrace debug log information.
Displays the contents of a stored Post Mortem Dump (PMD) file.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -177
Download from Www.Somanuals.com. All Manuals Search And Download.
debug systrace watch
Enables the sysTrace log on the console, or turns off (disables) the console display.
debug systrace watch {enable | disable}
Syntax Definitions
N/A
Defaults
parameter
default
enable | disable
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug systrace watch enable
-> debug systrace watch disable
Release History
Release 5.1; command was introduced.
Related Commands
Enables or disables kTrace logging.
Adds or removes a kTrace capture level for a specified subsystem.
Displays current kTrace parameters.
Displays kTrace log information.
Enables or disables sysTrace Logging
Adds or removes a sysTrace capture level for a specified subsystem.
Displays sysTrace debug log information.
Displays the contents of a stored Post Mortem Dump (PMD) file.
MIB Objects
N/A
page -178
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug systrace show
Displays sysTrace debug log information (e.g., sysTrace status, Application IDs with non-default Severity
Level settings).
debug systrace show
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug systrace show
sysTrace is:
- INITIALIZED
- RUNNING
- configured to TRACE CALLERS
- configured to NOT WATCH on stdout
Only applications not at the level ‘info’ (6) are shown
Application ID
Level
--------------------------------------------------------
SNMP
MIPGW
SYSTEM
(68) debug 1 (7)
(70) debug 1 (7)
(75) debug 3 (9)
Output fields are described here:
output definitions
Application ID
The Application ID (subsystem) for which the Severity Level is not set
to the info (6) default setting.
Level
The Severity Level of the above-referenced Application ID. Levels
include off (1), alarm (2), error (3), alert (4), warning (5), info (6),
debug1 (7), debug2 (8), and debug3 (9).
Release History
Release 5.1; command was introduced.
OmniSwitch Troubleshooting Guide September 2005
page -179
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Enables or disables kTrace logging.
Adds or removes a kTrace capture level for a specified subsystem.
Displays current kTrace parameters.
Displays kTrace log information.
Enables or disables sysTrace logging.
Enables or disables sysTrace log output to the console.
Adds or removes a sysTrace capture level for a specified subsystem.
Displays the sysTrace log.
Displays the contents of a stored Post Mortem Dump (PMD) file.
MIB Objects
N/A
page -180
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug systrace appid level
Adds or removes a sysTrace capture level for a specified application ID (i.e., subsystem).
debug systrace appid {app_id | integer} level {level | integer}
debug systrace no appid app_id
Syntax Definitions
app_id
An application ID keyword value. Currently supported application IDs
are listed below.
appid integer
A numerical equivalent value for the application ID. Currently
supported numeric equivalent values are listed below.
Supported Application IDs and Numerical Equivalents
802.1q - 7
aaa - 20
amap - 18
bridge - 10
chassis - 64
cli - 67
config - 66
dbggw - 89
diag - 0
distrib - 84
drc - 74
eipc - 26
epilogue - 85
ftp - 82
gmap - 19
gm - 9
health - 76
idle - 255
interface - 6
ip - 15
ipc-diag - 1
ip-helper - 22
ipc-link - 4
ipc-mon - 21
ipms - 17
ipx - 16
lanpower - 108
ldap - 86
linkagg - 12
mipgw - 70
module - 24
nan-driver - 78
ni-supervision - 5
nosnmp - 87
pmm - 23
psm - 81
qdispatcher - 3
qdriver - 2
qos - 13
rmon - 79
rsvp - 14
session - 71
slb - 25
smni - 83
snmp - 68
ssh - 109
ssl - 88
stp - 11
system - 75
telnet - 80
trap - 72
vlan - 8
vrrp - 77
web - 69
policy - 73
port-mgr - 65
level
The severity level keyword for the application ID (shown below). All
sysTrace events of the specified level and lower will be captured.
level integer
A numerical equivalent value for the severity level (shown below).
Values may range from 1–9.
Supported Levels Numeric Equivalents Description
Off.
off
1
2
3
4
5
6
7
8
9
Highest severity. The system is about to crash and reboot.
System functionality is reduced.
alarm
error
A violation has occurred.
alert
A unexpected, non-critical event has occurred.
Any other non-debug message (default).
A normal event debug message.
warning
info
debug1
debug2
debug3
A debug-specific message.
Lowest severity. A maximum verbosity debug message.
OmniSwitch Troubleshooting Guide September 2005
page -181
Download from Www.Somanuals.com. All Manuals Search And Download.
Defaults
parameter
default
level
info
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• You may enter more than one application ID in the command line. Separate each application ID with a
space.
• Application IDs may be entered in any order.
Examples
-> debug systrace appid 254 level off
-> debug systrace appid policy level info
-> debug systrace appid policy snmp web aaa vlan level alert
-> debug systrace no appid debug2
Release History
Release 5.1; command was introduced.
Related Commands
Enables or disables kTrace logging.
Adds or removes a kTrace capture level for a specified subsystem.
Displays current kTrace parameters.
Displays kTrace log information.
Enables or disables sysTrace logging.
Enables or disables sysTrace log output to the console.
Displays sysTrace debug log information.
Displays the sysTrace log.
Displays the contents of a stored Post Mortem Dump (PMD) file.
MIB Objects
N/A
page -182
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug systrace show log
Displays sysTrace log information.
debug systrace show log [file]
Syntax Definitions
file
Specifies a particular file from which sysTrace log information will be
displayed.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug systrace show log filename
TimeStamp
AppID
Trace Level Task
Caller
Session ID Comment
-----------------+----------+--------------------+-----------+--------------+-------------+----------------
0xd3db513d 0x43 CLI
0x6 info 0x00ccd590 CliShell0 0x0305f608 0xffffffff
[CLISHELL2] INIT socket nb : 175, local APP_ID: 67 and SNAP_ID: 66(TRUNCATED)
0xd3db4ff1 0x43 CLI 0x6 info 0x00ccd590 CliShell0 0x0305f608 0xffffffff
[CLISHELL2] INIT socket nb : 174, local APP_ID: 67 and SNAP_ID: 2(TRUNCATED)
0xd3db4f47 0x43 CLI 0x6 info 0x00ccd590 CliShell0 0x030732bc 0xffffffff
[CTRACE] CLI(ccd590) INITIALIZED address=3178b68/size=4096
0xd3db4ed8 0x43 CLI 0x6 info 0x00ccd590 CliShell0 0x0305f914 0xffffffff
[CLISHELL2] Task spawned, inactivity timer: 100000,file descriptor: 61
0xc6d8b3e0 0x43 CLI 0x6 info 0x00cd1890 N/A 0x03073454 0xffffffff
[CTRACE] CLI (cd1890) end by cd1890 address=16d1de0/size=4096
0x0e0641fe 0x4b SYSTEM 0x5 warning 0x03186c10 tMemMon 0x000a7ad4 0xffffffff
Task tShell has a memory leak at address 0x01527d68. Size is 52.
0x0e0641e7 0x4b SYSTEM 0x5 warning 0x03186c10 tMemMon 0x000a7ad4 0xffffffff
Task tShell has a memory leak at address 0x035ff510. Size is 129.
0x0e0641d0 0x4b SYSTEM 0x5 warning 0x03186c10 tMemMon 0x000a7ad4 0xffffffff
Task tShell has a memory leak at address 0x035ff478. Size is 140.
0x0e0641b8 0x4b SYSTEM 0x5 warning 0x03186c10 tMemMon 0x000a7ad4 0xffffffff
Task tShell has a memory leak at address 0x035ff3e0. Size is 140.
0x0e0641a1 0x4b SYSTEM 0x5 warning 0x03186c10 tMemMon 0x000a7ad4 0xffffffff
Task tShell has a memory leak at address 0x01096590. Size is 140.
0x010fb724 0x4b SYSTEM 0x5 warning 0x03186c10 tMemMon 0x000a7ad4 0xffffffff
Task has a memory leak at address 0x031773d0. Size is 32.
0x010a5e85 0x4b SYSTEM 0x6 info0x035ffd60 N/A 0x000b2da4 0xffffffff ====>SYSTEM
BOOT THU DEC 13 02:06:48 2001 <=====
0x010a5e28 0x4b SYSTEM 0x6 info0x035ffd60 N/A 0x00067c9c 0xffffffff initializ-
ing sysTrace, trace buffer at 0x31c0938, size=16384 entries.
OmniSwitch Troubleshooting Guide September 2005
page -183
Download from Www.Somanuals.com. All Manuals Search And Download.
Output fields are described here:
output definitions
Timestamp
The timestamp indicating when the sysTrace log entry occurred. Values
can range from 0x00000000 through 0xffffffff.
AppID
The Application ID for which the stored sysTrace log information is
displayed. Values can range from 0x00 through 0xff.
Trace Level
The Severity Level for which the stored sysTrace log information is
displayed.
Task
The Task for which the stored sysTrace log information is displayed.
The function that called the sysTrace log.
Caller
Session ID
The Session ID for which the stored sysTrace log information is dis-
played. Values can range from 0x00000000 through 0xffffffff.
Comment
The condition that resulted in the sysTrace log entry.
Release History
Release 5.1; command was introduced.
Related Commands
Enables or disables kTrace logging.
Adds or removes a kTrace capture level for a specified subsystem.
Displays current kTrace parameters.
Displays kTrace log information.
Enables or disables sysTrace logging.
Enables or disables sysTrace log output to the console.
Adds or removes a sysTrace capture level for a specified subsystem.
Displays sysTrace debug log information.
Displays the contents of a stored Post Mortem Dump (PMD) file.
MIB Objects
N/A
page -184
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
show log pmd
Displays the contents of a stored Post Mortem Dump (PMD) file. The PMD file is a diagnostic aid that
stores system information following some precipitating event (e.g., a system error).
show log pmd file_name [type type_string | id registrationidentifier_int | subid subidentifier_int |
taskname taskname_string | taskid tasknumber_int | record recordtype_string | address address_int]
Syntax Definitions
file_name
Specifies a file containing the PMD dump information.
type_string
Specifies a registration type. Valid registration types include
task, application, user-defined.
registrationidentifier_int
subidentifier_int
Specifies a registration identifier. Valid identifiers include task
number, unique value, snap/app id.
Specifies a value that is unique when used with the registration type and
registration identifier.
taskname_string
tasknumber_int
recordtype_string
Specifies the name associated with the desired task.
Specifies the numeric value corresponding with the desired task.
Specifies a record type. Valid record types include userdefined,
stackinfo, taskinfo, taskname, textstring, rawmemory, stacktrace,
tasknumber.
address_int
Specifies the address of the data buffer (specified in the original regis-
tration), to which memory list data will be sent.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
If no additional filter parameter is entered, all stored PMD file information will be displayed.
Examples
-> show log pmd filename
PMD Version -> 102
File Dump Type -> Mixed
Date Created - Coordinated universal time: Wed Dec 19 09:22:27 2001
----------------------------------------------------------------------------------
Registration Type ->Application
Application Id. ->4b
OmniSwitch Troubleshooting Guide September 2005
page -185
Download from Www.Somanuals.com. All Manuals Search And Download.
Record Type -> MemoryData Address -> 1b2b74 Size -> c4
0 0 0 7 0 6e 31 3d 3 3e df 5 0 0 37 54 0 0 18 b6 0 0 11 87 0 0 7a 88
0 0 2c 4f
0 0 c7 58 0 0 58 40 0 0 53 fc 0 0 b9 f0 0 0 d6 71 0 7 4c 54 0 6 a6 48
0 d c3 20
0 4e 6f 24 0 0 9e c5 0 23 2a 2 0 5 77 c4 0 2 91 f1 0 1 63 8 0 7 d 8
0 4 2c 6
0 9 3e d4 0 e dd 7e 0 24 2d 4 0 2a 43 e0 0 a1 4 89 0 80 1c d7 1 7e c1 dd
0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2f
3 18 42 50
3 43 8 d0 0 0 0 0 3 43 9 18 2 6a 7e 38 0 0 0 0 3 43 8 e8 2 21 42 b0
3 43 7 90
3 18 15 0
-------------------------------------------------------------
Registration Type ->Task
Task No. ->3571290
Record Type -> TaskName Task Id -> 3571290
tExcTask
-------------------------------------------------------------
Registration Type ->Task
Record Type -> StackCheck
Task No. ->3571290
Task Id -> 3571290
NAME
ENTRY
TID
SIZE CUR HIGH MARGIN
------------ ------------ -------- ----- ----- ----- ------
tExcTask excTask 3571290 19984 976 3488 16496
-------------------------------------------------------------
Registration Type ->Task
Record Type -> StackTrace
Task No. ->3571290
Task Id -> 3571290
e371c vxTaskEntry
fb304 excTask
130578 msgQReceive
9e)
+c : excTask (0, 0, 0, 0, 0, 0)
+24 : msgQReceive (1b8c00, 3571120, 1c, ffffffff, 0, 0)
+278: qJobGet (10000003, ffffffff, 7a000400, 1b8c00, 1ed400,
-------------------------------------------------------------
Registration Type ->Task Task No. ->3571290
Record Type -> TaskInfo Task Id -> 3571290
Address -> 0 Size -> 40
task id= 3571290
task priority= 0
task status= 2
task option bits= 7
original entry point of task= fb2e0
size of stack in bytes= 4e10
current stack usage in bytes= 3d0
maximum stack usage in bytes= da0
current stack margin in bytes = 4070
most recent task error status = 3d0001
delay/timeout ticks = 0
saved stack pointer= 3570ec0
the bottom of the stack= 3571290
the effective end of the stack= 356c480
the actual end of the stack= 356c470
-------------------------------------------------------------
page -186
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Registration Type ->Task
Record Type -> UserDefined
Address -> 1adcc38 Size -> 10
Task No. ->3571290
Task Id -> 3571290
46 69 72 73 74 20 69 74 65 72 61 74 69 6f 6e a
-------------------------------------------------------------
Registration Type ->Task
Record Type -> UserDefined
Address -> 1adcc50 Size -> 11
Task No. ->3571290
Task Id -> 3571290
53 65 63 6f 6e 64 20 69 74 65 72 61 74 69 6f 6e a
-------------------------------------------------------------
Registration Type ->Task
Task No. ->356b990
Record Type -> TaskName Task Id -> 356b990
tLogTask
-------------------------------------------------------------
Registration Type ->Task
Record Type -> StackCheck
Task No. ->356b990
Task Id -> 356b990
NAME
ENTRY
TID
SIZE CUR HIGH MARGIN
------------ ------------ -------- ----- ----- ----- ------
tLogTask logTask 356b990 8176 976 1168 7008
-------------------------------------------------------------
Registration Type ->Task
Record Type -> StackTrace
Task No. ->356b990
Task Id -> 356b990
e371c vxTaskEntry
100cac logTask
&fppTaskRegsCFmt, 9e)
130578 msgQReceive
0)
+c : logTask (0, 0, 0, 0, 0, 0)
+2c : msgQReceive (1b8c00, 356b820, 20, ffffffff,
+278: qJobGet (10000003, ffffffff, 7a000400, 1b8c00, 1ed400,
-------------------------------------------------------------
Registration Type ->Task Task No. ->356b990
Record Type -> TaskInfo Task Id -> 356b990
Address -> 0 Size -> 40
task id= 356b990
task priority= 0
task status= 2
task option bits= 6
original entry point of task= 100c80
size of stack in bytes= 1ff0
current stack usage in bytes= 3d0
maximum stack usage in bytes= 490
current stack margin in bytes = 1b60
most recent task error status = 0
delay/timeout ticks = 0
saved stack pointer= 356b5c0
the bottom of the stack= 356b990
the effective end of the stack= 35699a0
the actual end of the stack= 3569990
-------------------------------------------------------------
OmniSwitch Troubleshooting Guide September 2005
page -187
Download from Www.Somanuals.com. All Manuals Search And Download.
Output fields are described here:
output definitions
PMD Version
File Dump Type
Date Created
Registration Type
Application ID
Record Type
Address
The Post Mortem Dump (PMD) version ID.
The file dump type.
The date when the log was created.
The type of data being registered with PMD.
The ID of the Application registering with PMD.
The type of data registered with PMD.
The address of the data being registered.
The size (number of bytes) being registered.
The number of the task registering with PMD.
The vxWorks Task ID of the task registering with PMD.
The priority of the task registering with PMD.
The status of the task registering with PMD.
The option bits of the task registering with PMD.
Size
Task Number
Task ID
Task Priority
Task Status
Task Option Bits
Original Entry Point of Task The starting function of the task registering with PMD.
Size of Stack (bytes)
The size of the stack of the task registering with PMD.
Current Stack Usage (bytes)
The amount of the stack currently being used by the task registered
with PMD.
Maximum Stack Usage (bytes) The maximum amount of the stack used by the task registered with
PMD.
Task Error Status
Delay/Timeout Ticks
Saved Stack Pointer
Bottom of Stack
The current error status of the task registering with PMD.
The number of ticks that the task will delay before becoming active.
The stack pointer of the task registered with PMD.
The base of the task’s stack of the task registered with PMD.
The end of the task’s stack based upon the size shown previously.
The actual end of the task’s stack.
Effective End of Stack
Actual End of Stack
Release History
Release 5.1; command was introduced.
Related Commands
N/A
MIB Objects
N/A
page -188
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug memory monitor
Enables or disables memory monitoring functions.
debug memory monitor {enable | disable}
Syntax Definitions
enable
disable
Enables memory monitoring.
Disables memory monitoring.
Defaults
parameter
default
disable
enable | disable
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug memory monitor enable
-> debug memory monitor disable
Release History
Release 5.1; command was introduced.
Related Commands
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -189
Download from Www.Somanuals.com. All Manuals Search And Download.
debug memory monitor show status
The debug memory monitor show status command displays memory monitoring status information.
debug memory monitor show status
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug pmd ni 3/0
Release History
Release 5.1; command was introduced.
Related Commands
page -190
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
debug memory monitor show log
Displays memory monitoring log information.
debug memory monitor show log
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug memory monitor show log
Task
Memory Memory Addrof OSfunc Calling Previous
Name Comments Addr
Size OS call Called Function Caller
----------+----------+---------------+-----------+--------+---------+-------------+-------------------------
tssApp_2* TCB Stac 00ca1550 20680 0013a180 objAllocEx taskSpawn ssAppChild
tssApp_2* Vx B Sem 02317ca8
tssApp_2* Vx B Sem 02317f78
28 001374d0 objAlloc pipe
28 001374d0 objAlloc pipe
0107be78 5121 0012cfc8 malloc pipe
ssAppChild
ssAppChild
ssAppChild
ssAppChild
ssAppChild
tssApp_2*
tssApp_2*
tssApp_2*
tssApp_2*
023182b0 16 0012cfa8 malloc
024fdc90 9 00105fb0 malloc
016d6548 288 000af228 malloc
pipe
pipe
ssAppChild mip_msg_qu
CliShell0 Vx C Sem 035fe590
28 0011f038 semCCreate zcSelect mip_msg_do
SsApp
Vx C Sem 035fe4b8 28 0011f038 semCCreate zcSelect tssAppMain
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
02318250
02317538
016d6670 272 02b33a3c malloc
02318260
02317718
016d68b0 272 02b33a3c malloc
023182c8
027b0060
01896b28 272 02b33a3c malloc
023182d8
035fe4e0
01e3d928 272 02b33a3c malloc
024fdca8
035fe3e0
022b3ab0 272 02b33a3c malloc
024fdcb8
01e37e40
022b3bc8 272 02b33a3c malloc
2 02b33a3c malloc
56 02b33a3c malloc
SSLexLexem SSYaccStac
SSLexLexem SSYaccStac
SSYaccStac SSYaccPars
SSLexLexem SSYaccStac
SSLexLexem SSYaccStac
SSYaccStac PropagateP
SSLexLexem SSYaccStac
SSLexLexem SSYaccStac
SSYaccStac SSYaccPars
SSLexLexem SSYaccStac
SSLexLexem SSYaccStac
SSYaccStac SSYaccPars
SSLexLexem SSYaccStac
SSLexLexem SSYaccStac
SSYaccStac SSYaccPars
SSLexLexem SSYaccStac
SSLexLexem SSYaccStac
SSYaccStac SSYaccPars
1 02b33a3c malloc
56 02b33a3c malloc
4 02b33a3c malloc
56 02b33a3c malloc
4 02b33a3c malloc
56 02b33a3c malloc
4 02b33a3c malloc
56 02b33a3c malloc
3 02b33a3c malloc
56 02b33a3c malloc
OmniSwitch Troubleshooting Guide September 2005
page -191
Download from Www.Somanuals.com. All Manuals Search And Download.
CliShell0
CliShell0
CliShell0
CliShell0
CliShell0
Stp
02314da8 272 02b33a3c malloc
023183d8 512 02b33a3c malloc
027b0100 576 02b33a3c malloc
0107a128 2404 02b33a3c malloc
0107aa98 1280 02b33a3c malloc
SSYaccStac SSYaccInit
CliParse clishell_m
CliParse clishell_m
CliParse clishell_m
CliParse clishell_m
Vx C Sem024fdcc8 28 0011f038 semCCreate zcSelect stpSock_st
LnkAgg Vx C Sem 023182e8 28 0011f038 semCCreate zcSelect lagg_Sock_
AmapMgr Vx C Sem 02318270 28 0011f038 semCCreate zcSelect xmap_main_
GrpMob Vx C Sem 035fe5b8 28 0011f038 semCCreate zcSelect gmcWaitFor
GmapMgr Vx C Sem 02317fa0
VlanMgr Vx C Sem 02317cd0
NanDrvr Vx C Sem 02318158
28 0011f038 semCCreate zcRecvfrom gmap_main_
28 0011f038 semCCreate zcSelect vmcWaitFor
28 0011f038 semCCreate zcRecvfrom nanDriver
Output fields are described here:
output definitions
Task Name
Comments
The task that “owns” the memory block.
The type of memory block that has been allocated. Comments include:
• TCB Stack—this block belongs to the task whose name is listed
• PX Msg Q—Posix Message Queue
• Vx Msg Q—vxWorks Message Queue
• P Sem—Posix Semaphore
• Vx B Sem—vxWorks binary semaphore
• Vx C Sem—vxWorks counting semaphore
• Vx M Sem—vxWorks mutual exclusion semaphore
• Leak—Memory leak.
Memory Address
Memory Size
The address of the memory block.
The size of the memory block.
Address of OS Call
OS Function Called
Calling Function
Previous Caller
The address of the call that allocated the block.
The function that contained the call that allocated the block.
The function that called the above-mentioned function.
The function that called the above-mentioned function.
Release History
Release 5.1; command was introduced.
page -192
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Enables or disables memory monitoring functions.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -193
Download from Www.Somanuals.com. All Manuals Search And Download.
debug memory monitor show log global
Displays memory monitoring global statistics.
debug memory monitor show log global
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug memory monitor show log global
Current
= 33741
Cumulative = 687952
Output fields are described here:
output definitions
Current
The amount of dynamic memory allocated (currently) since the last
enable.
Cumulative
The amount of dynamic memory allocated (cumulative) since the last
enable.
Release History
Release 5.1; command was introduced.
page -194
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Enables or disables memory monitoring functions.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -195
Download from Www.Somanuals.com. All Manuals Search And Download.
debug memory monitor show log task
Displays memory monitoring task statistics.
debug memory monitor show log task
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug memory monitor show log task
Task Name
Current
Cumulative
----------------+-------------+-------------
tssApp0_4
cliConsole
tIpxGapper
tIpxTimer
tDrcIprm
DrcTm
26369
16169
242
52594
20186
242
214
214
1801287
479453
53690
285084
578
1801315
675448
340083
334616
578
15704
938852
8348
WebView
Rmon
SlbCtrl
PolMgr
Qos
808
47096
8320
UdpRly
Vrrp
622
1198
Ipx
ipmpm
ipmfm
Ipmem
29634
231152
480422
423686
9128
284
86988
128
29634
231152
480450
423686
263872
891188
1867592
184
GmapMgr
AmapMgr
LnkAgg
8021q
stpTick
Stp
GrpMob
SrcLrn
EsmDrv
PsMgr
1024
70782
128
12516
356
1024
1555454
669300
12572
74752
308
168
L3Hre
528
528
page -196
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Health
AAA
Ipedr
NanDrvr
Ftpd
249
221312
31500
56
127649
222236
105868
74396
56
56
Telnetd
tCS_CVM
tssApp65535_3
SsApp
9552
28
228
49088
69200
26347
4548
2336
208
804
84
228
1240
188
9552
28
228
198284
202029
210129
63976
2392
149672
75424
140
SesMgr
SNMPagt
TrapMgr
EIpc
VlanMgr
PortMgr
Gateway
CfgMgr
897491
2500
tCS_HSM
tCS_CMS
tCS_PRB
tCS_CCM
tCsCSMtask
tSwLogTask
328
340
12555
15256874
13519+
312
612
586128
Output fields are described here:
output definitions
Task Name
Current
The task that “owns” the memory block.
The amount of dynamic memory allocated (currently) since log was
enabled.
Cumulative
The amount of dynamic memory allocated (cumulative) since log was
enabled.
Release History
Release 5.1; command was introduced.
Related Commands
Enables or disables memory monitoring functions.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -197
Download from Www.Somanuals.com. All Manuals Search And Download.
debug memory monitor show log size
Displays memory monitoring size statistics.
debug memory monitor show log size
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug memory monitor show log size
Lower Upper Currently Cummulatively
Limit Limit Allocated
Allocated
-----+-----+-------------+-------------+
0
16
32
16
32
64
14439
6299
4833
31689
7704923
373109
145775
122315
228673
365552
358630
274071
1534291
673610
1075783
1588017
25675316
64 128
128 256
256 512
512 1024
1024 2048
2048 4096
4096 8192
8192 16384
16384 32768
32768 65536
65536
44248
12367
52096
26778
24572
49648
50793
478292
431784
850216
5130020
Output fields are described here:
output definitions
Lower Limit
The lower limit of the memory size range being measured.
The upper limit of the memory size range being measured.
The amount of memory currently allocated (in bytes).
The amount of memory cumulatively allocated (in bytes).
Upper Limit
Currently Allocated
Cummulatively Allocated
page -198
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Release History
Release 5.1; command was introduced.
Related Commands
Enables or disables memory monitoring functions.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -199
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ktrace
Enables or disables kTrace logging. The kernel trace, or kTrace, facility provides a consistent, low-level
mechanism for capturing integer-based event records in a history buffer. This trace facility will generally
be used by lower level functions to track information, such as which task is operating.
debug ktrace {enable | disable}
Syntax Definitions
enable
disable
Enables kTrace logging.
Disables kTrace logging.
Defaults
parameter
default
enable
enable | disable
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug ktrace enable
-> debug ktrace disable
Release History
Release 5.1; command was introduced.
page -200
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Adds or removes a kTrace capture level for a specified subsystem.
Displays current kTrace parameters.
Displays kTrace log information.
Enables or disables sysTrace logging.
Enables or disables sysTrace log output to the console.
Adds or removes a sysTrace capture level for a specified subsystem.
Displays sysTrace debug log information.
Displays the sysTrace log.
Displays the contents of a stored Post Mortem Dump (PMD) file.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -201
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ktrace show
Displays current kTrace parameters (e.g., kTrace status, Application IDs with non-default Severity Level
settings).
debug ktrace show
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug ktrace show
kTrace is:
- INITIALIZED
- RUNNING
- configured to TRACE CALLERS
All applications have their trace level set to the level ‘info’ (6)
Output fields are described here:
output definitions
Application ID
If an Application ID (subsystem) keyword is displayed, such as SNMP
(68), its Severity Level is not set to the info (6) default setting.
Level
The Severity Level of the above-referenced Application ID. Levels
include off (1), alarm (2), error (3), alert (4), warning (5), info (6),
debug1 (7), debug2 (8), and debug3 (9).
Release History
Release 5.1; command was introduced.
page -202
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Commands
Enables or disables kTrace logging.
Adds or removes a kTrace capture level for a specified subsystem.
Displays kTrace log information.
Enables or disables sysTrace logging.
Enables or disables sysTrace log output to the console.
Adds or removes a sysTrace capture level for a specified subsystem.
Displays sysTrace debug log information.
Displays the sysTrace log.
Displays the contents of a stored Post Mortem Dump (PMD) file.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -203
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ktrace appid level
Adds or removes a kTrace capture level for a specified application ID (i.e., subsystem).
debug ktrace appid {app_id | integer} level {level | integer}
debug ktrace no appid app_id
Syntax Definitions
app_id
An application ID keyword value. Currently supported application IDs
are listed below.
appid integer
A numerical equivalent value for the application ID. Currently
supported numeric equivalent values are listed below.
Supported Application IDs and Numeric Equivalents
802.1q - 7
aaa - 20
bridge - 10
chassis - 64
cli - 67
config - 66
dbggw - 89
diag - 0
ipc-diag - 1
ip-helper - 22
ipc-link - 4
ipc-mon - 21
ipms - 17
psm - 81
qdispatcher - 3
qdriver - 2
qos - 13
rmon - 79
rsvp - 14
session - 71
slb - 25
ipx - 16
lanpower - 108
ldap - 86
distrib - 84
drc - 74
eipc - 26
epilogue - 85
ftp - 82
health - 76
idle - 255
interface - 6
ip - 15
linkagg - 12
mipgw - 70
module - 24
nan-driver - 78
ni-supervision - 5
nosnmp - 87
pmm - 23
smni - 83
snmp - 68
ssl - 88
stp - 11
system - 75
telnet - 80
trap - 72
vlan - 8
policy - 73
port-mgr - 65
vrrp - 77
web - 69
level
The severity level keyword for the application ID (shown below). All
kTrace events of the specified level and lower will be captured.
level integer
A numerical equivalent value for the severity level (shown below).
Values may range from 1–9.
Supported Levels Numeric Equivalents Description
Off.
off
1
2
3
4
5
6
7
8
9
Highest severity. The system is about to crash and reboot.
System functionality is reduced.
alarm
error
A violation has occurred.
alert
A unexpected, non-critical event has occurred.
Any other non-debug message (default).
A normal event debug message.
warning
info
debug1
debug2
debug3
A debug-specific message.
Lowest severity. A maximum verbosity debug message.
page -204
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Defaults
parameter
default
level
info (6)
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• You may enter more than one application ID in the command line. Separate each application ID with a
space.
• Application IDs may be entered in any order.
Examples
-> debug ktrace appid 254 level off
-> debug ktrace appid policy level info
-> debug ktrace appid policy snmp web aaa vlan level alert
-> debug ktrace no appid debug2
Release History
Release 5.1; command was introduced.
Related Commands
Enables or disables kTrace logging.
Displays current kTrace parameters.
Displays kTrace log information.
Enables or disables sysTrace logging.
Enables or disables sysTrace log output to the console.
Adds or removes a sysTrace capture level for a specified subsystem.
Displays sysTrace debug log information.
Displays the sysTrace log.
Displays the contents of a stored Post Mortem Dump (PMD) file.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -205
Download from Www.Somanuals.com. All Manuals Search And Download.
debug ktrace show log
Displays kTrace log information.
debug ktrace show log [file]
Syntax Definitions
file
Specifies a particular file from which kTrace log information will be
displayed.
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
N/A
Examples
-> debug ktrace show log
Event
Timestamp AppID Level
Task ID Caller (arg1, arg2, arg3, arg4)
-----------+--------------+--------+-------------+--------+---------------------------------------------
TSWITCH 0x4cad9a4 0x4b info (6) SSAppKTL (0x00ca6370) 0x00066578 0x027b23b0
0x00ca6370 0x00000000 0x00000000
TSWITCH 0xd4cad98d 0x4b info (6) ipcInteg (0x027b23b0) 0x00066578 0x00ca6370
0x027b23b0 0x00000000 0x00000000
TSWITCH 0xd4cad8ae 0x4b info (6) SSAppKTL (0x00ca6370) 0x00066578 0x03186c10
0x00ca6370 0x00000000 0x00000000
TCREATE 0xd4cad810 0x4b info (6) tssApp_2 (0x00cab440) 0x000665d0 0x00ca6370
0x00000000 0x00000000 0x00000000
TSWITCH 0xd4cad787 0x4b info (6) tssApp_2 (0x00cab440) 0x00066578 0x03186c10
0x00cab440 0x00000000 0x00000000
TSWITCH 0xd4cad77c 0x4b info (6) tMemMon (0x03186c10) 0x00066578 0x00cab440
0x03186c10 0x00000000 0x00000000
TSWITCH 0xd4cad771 0x4b info (6) tssApp_2 (0x00cab440) 0x00066578 0x00cab440
0x03186c10 0x00000000 0x00000000
TSWITCH 0xd4cad751 0x4b info (6) tMemMon (0x03186c10) 0x00066578 0x03186c10
0x00cab440 0x00000000 0x00000000
KICKDOG 0xd276db09 0x4b info (6) tCsCSMta (0x022fb0d0) 0x00046760 0x0000001e
0x0000001e 0x00000002 0x0000001e
TSWITCH 0xd276d875 0x4b info (6) SSApp (0x01d62350) 0x00066578 0x03186c10
0x01d62350 0x00000000 0x00000000
page -206
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Output fields are described here:
output definitions
Event
The event for which kTrace log information is displayed.
Timestamp
The timestamp for the kTrace log information being displayed. Values
can range from 0x00000000 through 0xffffffff.
AppID
Level
The Application ID (subsystem) for which kTrace log information is
displayed. Values can range from 0x00 through 0xff.
The Severity Level for which kTrace log information is displayed.Val-
ues include off (1), alarm (2), error (3), alert (4), warning (5), info (6)
(default) debug1 (7), debug2 (8), and debug3 (9).
Task ID
Caller
The Task for which kTrace log information is displayed.
The address of the function containing the call that logged the event.
Release History
Release 5.1; command was introduced.
Related Commands
Enables or disables kTrace logging.
Adds or removes a kTrace capture level for a specified subsystem.
Displays current kTrace parameters.
Enables or disables sysTrace logging.
Enables or disables sysTrace log output to the console.
Adds or removes a sysTrace capture level for a specified subsystem.
Displays sysTrace debug log information.
Displays the sysTrace log.
Displays the contents of a stored Post Mortem Dump (PMD) file.
MIB Objects
N/A
OmniSwitch Troubleshooting Guide September 2005
page -207
Download from Www.Somanuals.com. All Manuals Search And Download.
page -208
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
C Technical Support
Commands
This chapter describes Technical Support Command Line Interface (CLI) show commands that create log
files of the output from multiple standard CLI show commands. These log files can be transferred with
FTP to a workstation for off-line analysis and troubleshooting.
Note. See the OmniSwitch CLI Reference Guide for more information on standard CLI show commands.
A summary of available commands is listed here:
OmniSwitch Troubleshooting Guide September 2005
page -1
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support
Creates a log file of the output of several system-wide Command Line Interface (CLI) commands.
show tech-support
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support.log in the /flash directory of the output produced by
the show hardware info, show chassis, show module long, show fan, show power, show
temperature, show system, show running-directory, show microcode certified, show microcode
working, show microcode loaded, debug ipc pools slot, show aaa authentication, show health,
show vlan, show spantree, show interfaces status, show ip interface, show ip config, and show ip
protocols CLI commands.
• If an existing file called tech_support.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
Examples
-> show tech-support
....................
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of several Layer 2 CLI commands.
Creates a log file of the output of several Layer 3 CLI commands.
page -2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support layer2
Creates a log file of the output of several Layer 2 Command Line Interface (CLI) commands.
show tech-support layer2
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support_layer2.log in the /flash directory of the output
produced by the show interfaces, show interfaces accounting, show interfaces collisions, show vlan
port, show vlan port mobile, show linkagg, show linkagg port, show spantree ports,
show mac-address-table count, show mac-address-table aging-time, show mac-address-table,
debug fabric stats, debug fabric fbus, debug fabric errors, debug fabric input, and debug fabric
stats CLI commands.
• If an existing file called tech_support_layer2.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
Examples
-> show tech-support layer2
................
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of system-wide CLI commands.
Creates a log file of the output of several Layer 3 CLI commands.
OmniSwitch Troubleshooting Guide September 2005
page -3
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support layer3
Creates a log file of the output of several Layer 3 Command Line Interface (CLI) commands.
show tech-support layer3
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support_layer3.log in the /flash directory of the output
produced by the show vlan router mac status, show ip router database, show ip traffic, show icmp
statistics, show tcp statistics, show tcp ports, show udp statistics, show udp ports, show vrrp,
show vrrp statistics, show ip slb, show ip route, and show arp CLI commands.
• If an existing file called tech_support_layer3.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
• Server Load Balancing (SLB) is not supported on OmniSwitch 6624 and 6648 switches and therefore
the show ip slb command output is not relevant for these switches.
Examples
-> show tech-support layer3
.............
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of system-wide CLI commands.
Creates a log file of the output of several Layer 2 CLI commands.
page -4
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support layer3 rip
Creates a log file of the output of several Routing Information Protocol (RIP) Command Line Interface
(CLI) commands.
show tech-support layer3 rip
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support_rip.log in the /flash directory of the output produced
by the show ip rip, show ip rip routes, show ip rip redist-filter, show ip rip redist, show ip rip
interface, show ip rip peer, and show ip rip debug CLI commands.
• If an existing file called tech_support_rip.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
Examples
-> show tech-support layer3 rip
.......
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of system-wide CLI commands.
Creates a log file of the output of several Layer 2 CLI commands.
Creates a log file of the output of several Layer 3 CLI commands.
OmniSwitch Troubleshooting Guide September 2005
page -5
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support layer3 pimsm
Creates a log file of the output of several Protocol-Independent Multicast Sparse Mode (PIM-SM)
Command Line Interface (CLI) commands.
show tech-support layer3 pimsm
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support_pimsm.log in the /flash directory of the output
produced by the show ip pimsm, show ip pimsm neighbor, show ip pimsm rp-candidate, show ip
pimsm rp-set, show ip pimsm interface, show ip pimsm nexthop, show ip pimsm mroute, and
show ip pimsm debug CLI commands.
• If an existing file called tech_support_pimsm.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
Examples
-> show tech-support layer3 pimsm
........
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of system-wide CLI commands.
Creates a log file of the output of several Layer 2 CLI commands.
Creates a log file of the output of several Layer 3 CLI commands.
page -6
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support layer3 ospf
Creates a log file of the output of several Open Shortest Path First routing (OSPF) Command Line Inter-
face (CLI) commands.
show tech-support layer3 ospf
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support_ospf.log in the /flash directory of the output
produced by the show ip ospf, show ip ospf area, show ip ospf interface, show ip ospf neighbor,
show ip ospf lsdb, show ip ospf host, show ip ospf border-routers, show ip ospf ext-lsdb, show ip
ospf redist, show ip ospf redist-filter, show ip ospf routes, show ip ospf virtual-link, and show ip
ospf debug CLI commands.
• If an existing file called tech_support_ospf.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
Examples
-> show tech-support layer3 ospf
.............
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of system-wide CLI commands.
Creates a log file of the output of several Layer 2 CLI commands.
Creates a log file of the output of several Layer 3 CLI commands.
OmniSwitch Troubleshooting Guide September 2005
page -7
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support layer3 mroute
Creates a log file of the output of several multicast routing Command Line Interface (CLI) commands.
show tech-support layer3 pimsm
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support_mroute.log in the /flash directory of the output
produced by the show ip mroute, show ip mroute interface, show ip mroute-nexthop, show ip
mroute-boundary, and show ip mroute debug CLI commands.
• If an existing file called tech_support_mroute.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
Examples
-> show tech-support layer3 mroute
.....
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of system-wide CLI commands.
Creates a log file of the output of several Layer 2 CLI commands.
Creates a log file of the output of several Layer 3 CLI commands.
page -8
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support layer3 ipx
Creates a log file of the output of several Internet Packet Exchange (IPX) protocol Command Line Inter-
face (CLI) commands.
show tech-support layer3 ipx
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6624, 6648, 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support_ipx.log in the /flash directory of the output produced
by the show ipx interface, show ipx default-route, show ipx route, show ipx servers, show ipx
filter, show ipx type-20-propagation, show ipx packet-extension, and show ipx timers CLI
commands.
• If an existing file called tech_support_ipx.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
Examples
-> show tech-support layer3 ipx
.........
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of system-wide CLI commands.
Creates a log file of the output of several Layer 2 CLI commands.
Creates a log file of the output of several Layer 3 CLI commands.
OmniSwitch Troubleshooting Guide September 2005
page -9
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support layer3 dvmrp
Creates a log file of the output of several Distance Vector Multicast Routing Protocol (DVMRP)
Command Line Interface (CLI) commands.
show tech-support layer3 dvmrp
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support_dvmrp.log in the /flash directory of the output
produced by the show ip dvmrp, show ip dvmrp prune, show ip dvmrp route, show ip dvmrp
neighbor, show ip dvmrp interface, show ip dvmrp nexthop, show ip dvmrp tunnel, and show ip
dvmrp debug CLI commands.
• If an existing file called tech_support_dvmrp.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
Examples
-> show tech-support layer3 dvmrp
........
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of system-wide CLI commands.
Creates a log file of the output of several Layer 2 CLI commands.
Creates a log file of the output of several Layer 3 CLI commands.
page -10
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
show tech-support layer3 bgp
Creates a log file of the output of several Border Gateway Protocol (BGP) Command Line Interface (CLI)
commands.
show tech-support layer3 bgp
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 7700, 7800, 8800
Usage Guidelines
• This command creates a file called tech_support_bgp.log in the /flash directory of the output
produced by the show ip bgp, show ip bgp statistics, show ip bgp aggregate-address, show ip bgp
network, show ip bgp path, show ip bgp neighbors, show ip bgp neighbors policy, show ip bgp
neighbors statistics, show ip bgp policy community-list, show ip bgp redist-filter, show ip bgp
routes, and show ip bgp debug CLI commands.
• If an existing file called tech_support_bgp.log already exists then it will be overwritten when this
command is executed.
• See the OmniSwitch CLI Reference Guide for more information on show commands.
Examples
-> show tech-support layer3 bgp
............
Release History
Release 5.1; command was introduced.
Related Commands
Creates a log file of the output of system-wide CLI commands.
Creates a log file of the output of several Layer 2 CLI commands.
Creates a log file of the output of several Layer 3 CLI commands.
OmniSwitch Troubleshooting Guide September 2005
page -11
Download from Www.Somanuals.com. All Manuals Search And Download.
page -12
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
D Modifying Files with
VI Editor
The switch has a built in Unix text editor called VI.
This section covers some basic VI commands and how to use VI to modify the IP address of the EMP
(Ethernet Management Port), which is stored in the boot.params file. The boot.params file can also be
modified via MiniBoot.
In This Chapter
OmniSwitch Troubleshooting Guide September 2005
page -1
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful VI Commands
Useful VI Commands
The following are some useful VI commands:
u - undo the last command.
CTL/L -reprint current screen.
CTL/F-pages forward one screen.
CTL/B-pages back one screen.
j -moves cursor down one line.
k -moves cursor up one line.
h - moves cursor back one character.
l - moves cursor forward one character.
Enter key - moves cursor to the beginning of next line.
0 -zero moves cursor to beginning of current line.
$ -- moves cursor to end of current line.
space bar - moves cursor forward one character.
w-moves cursor forward to the next word.
e - moves cursor backward to the end of previous word.
b - moves cursor backward to the beginning of the previous word.
/ pattern - this will search for the entered pattern.
n - this will repeat the last search (/).
s - deletes current character and enters insertion mode.
J - Joins the current line with the next line.
a - append test after cursor. Use Esc key to terminate.
A - Append test at end of line. Use Esc key to terminate.
i - Inserts text before the cursor. Use Esc key to terminate.
I - Inserts text at the beginning of the line. Use Esc key to terminate.
o -Opens new line below current line for text insertion. Use Esc key to terminate.
O - Opens new line above the current line for text insertion. Use Esc key to terminate.
Delete key - Overwrites last character during text insertion.
Esc key -Stops text insertion.
x - Deletes current character.
dd-Deletes the current line.
page -2
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Sample VI Session
Dew - Deletes the current word.
P - Puts back text from previous delete.
yy-Puts the current line in buffer; leaves the current line intact.
p-Places the line in the buffer after the current position of the cursor.
ZZ-Exits VI and saves the changes.
:q-quits VI session and does not save any of the changes.
Sample VI Session
The following is a sample way to use the VI editor to modify the boot.params file.
Note. The commands performed below are executed from the /flash directory (root).
vi boot.params
boot empipaddr 192.168.11.1:ffffff00
boot empgatewayipaddr 192.168.11.254
boot serialbaudrate 9600
boot serialparity none
boot serialwordsize 8
boot serialstopbits 1
boot serialmode modemControlOff
boot reboottimer 0
boot runningversion working
boot nextrunningversion certified
boot numresets 54
The following is one of the ways you could now edit the IP address listed above.
Type the letter l to move one space to the right (h to move to the left) until you are at the front of the IP
address you want to modify, and then issue the letter x to delete the character to the right; repeat until the
address is removed. Issue an i to insert characters, and type in the new address. When you are finished,
type ZZ to exit, and save your changes. If you do not want to save the changes issue the following:
:q!
OmniSwitch Troubleshooting Guide September 2005
page -3
Download from Www.Somanuals.com. All Manuals Search And Download.
Sample VI Session
page -4
OmniSwitch Troubleshooting Guide September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
CLI shell
command info
console
HRE A-13
DOS Commands
Dshell Commands
D
Debug Commands
page -2
OmniSwitch Troubleshooting Guide
September 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
M
memory monitor
Multicast Routing
N
NI slots
O
OmniSwitch 6624/6648
architecture A-43
OmniSwitch 7700/7800/8800
OSPF
P
DVMRP
PIM-SM
PMD
port information
port numbering
F
converting 1-36
ports
G
GMAP
Q
QoS
H
HRE A-13
HTTP sessions
R
RIP
I
interfaces
IP
IPC pools
S
Spanning Tree
switch fabric
sysTrace
K
kTrace
L
OmniSwitch Troubleshooting Guide September 2005
page -3
Download from Www.Somanuals.com. All Manuals Search And Download.
|