Aiwa Car Stereo System CDC Z117 User Manual

OPERATING INSTRUCTIONS  
MANUAL DE INSTRUCCIONES  
MODE D’EMPLOI  
CDC-Z117  
YU  
STEREO CAR CD RECEIVER  
RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA  
AUTOMOVIL  
ENGLISH  
ESPAÑOL  
FRANÇAIS  
OWNER’S RECORD  
For your convenience, record the model number and  
serial number (you will find them on the bottom side of  
your set) in the space provided below. Please refer to  
them when you contact your AIWA dealer in case of  
difficulty.  
Model No. CDC-Z117  
Serial No.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting sound  
BASIC OPERATION,  
AUDIO AND CLOCK  
ADJUSTMENT  
You can select the following modes for adjusting sound  
depending on the music you listen to: BASS (low  
frequencies), TRE (high frequencies), BAL (left/right),  
FAD (front/ rear) and H-BASS (high bass)  
1
Press SEL repeatedly to select the mode to be  
adjusted.  
Pressing SEL cycles through the modes. The  
selected mode’s indicator flashes.  
TurntheSmartJogtoincreaseordecreasethelevel  
for the selected mode (except for H-BASS).  
In H-BASS mode, turn the Smart Jog to select on or  
off.  
2
Smart Jog  
Note  
Adjust the level or select on/off within 5 seconds, or the  
selected mode will return to previous state.  
Turning the unit on/off  
• Press PWR/MUTE to turn on the unit. The unit also  
turns on when you insert a CD.  
• Press and hold PWR/MUTE until the unit turns off.  
Aligning the source levels  
(Source Level Adjuster)  
Note  
Volume may vary each time you change the source  
mode. In this case, you can align each source mode’s  
volume to almost the same level.  
Most operations described in this manual require the  
unittobeturnedonbeforestartingtheoperation, unless  
explicitly stated otherwise.  
1
2
PressFNCrepeatedlytoselectthedesiredmode.  
Press DISP while pressing SEL.  
Changing the source mode  
“LA 0” appears in the display.  
3
Turn the Smart Jog to adjust the level.  
1
Press FNC.  
Note  
Pressing FNC cycles through source modes in the  
following order:  
Adjust the level within 5 seconds, or the selected mode  
will be canceled.  
Restoring the factory settings  
* “CD” does not appear in the display when there is no  
CD in the unit.  
1
2
Turn off the unit.  
Press and hold DISP until “LA --” appears in the  
display.  
Adjusting the volume  
Note  
1
Turn the Smart Jog.  
YoucanrestorethefactorysettingsonlyforVOL,BASS,  
TRE, BAL, FAD, and H-BASS, and aligned source  
volume levels.  
VOL (volume) indicator flashes.  
Muting the sound  
Muting button beep sounds  
1
Press PWR/MUTE briefly.  
To restore volume, briefly press PWR/MUTE again.  
1
2
Turn off the unit.  
Press and hold SEL until “bEEP” appears in the  
display.  
3
4
Turn the Smart Jog to select on (level indicators  
appear) or off (level indicators disappear).  
Press and hold SEL until the unit turns off.  
ENGLISH 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the clock  
Monaural mode  
When signals become weak, or reception becomes  
poor, the unit automatically switches to Monaural mode  
to reduce noise.  
1
2
3
Press and holdDISP until the clock indicator flashes  
in the display.  
Press TUNEi (to set hour) or TUNEk (to set  
minute) and turn the Smart Jog.  
Press DISP.  
Local mode  
Local mode allows you to tune in only to strong stations  
during Seek Tuning.  
1
Press LO before you start seek tuning.  
“LO” appears in the display.  
Displaying the clock  
To return to Distant mode, press LO again.  
“LO” disappears and the unit tunes in to all receivable  
stations.  
1
Press DISP.  
To return to the former display, press DISP again.  
Using preset stations  
RADIO OPERATION  
Youmustpresetstationsbeforeyoucantuneinastation  
using preset station number buttons.  
Tuning in to a station  
(Seek/Manual Tuning)  
Preset station buttons 1 ~ 6  
Stereo indicator Local indicator  
Preset station  
number  
Band indicator Frequency indication  
Presetting stations automatically  
(Auto Memory)  
1
Press FNC repeatedly to select the desired band  
(FM1, FM2, FM3, AM1 or AM2).  
1
Press FNC repeatedly to select the desired band  
(FM1, FM2, FM3, AM1 or AM2).  
Press and hold PS/A.ME until automatic presetting  
starts.  
2* Press TUNEi (to move to higher frequencies) or  
TUNEk (to move to lower frequencies) to tune in to  
a station.  
2
“ST” appears in the display when a station is  
broadcasting in stereo, and receiving conditions are  
good.  
The unit automatically stores up to 6 stations for  
each band.  
After completion of automatic presetting, the unit  
tunes in to the station stored on preset station  
button 1.  
*Seek Tuning and Manual Tuning  
• Press and hold TUNEi or TUNEk until seek Tuning  
starts.  
Tocancelautomaticpresetting,pressPS/A.MEagain.  
The unit locates a station automatically (Seek Tuning).  
• Press TUNEi or TUNEk repeatedly to search for a  
desired station while increasing or decreasing the  
frequency step by step (Manual Tuning).  
To stop Seek Tuning, press TUNEi or TUNEk  
again.  
Checking the preset stations (Preset Scan)  
1
Press PS/A.ME briefly.  
Each preset station will be tuned in for 5 seconds in  
order.  
To cancel Preset Scan, press PS/A.ME again or any  
preset station button.  
3 ENGLISH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Presetting stations manually  
(Manual Memory)  
1
2
3
Press FNC repeatedly to select the desired band  
(FM1, FM2, FM3, AM1 or AM2).  
Press TUNEi or TUNEk to tune in to a desired  
station (see “Tuning in to a station,” page 3).  
Press the desired preset station button until the unit  
beeps.  
MY INFO indicator  
Smart Job  
Note  
Setting the timer  
A newly preset station replaces the station on the same  
band that was previously stored on that preset station  
button.  
1
2
Turn off the unit.  
Press and hold INFO until “PO” flashes in the  
display.  
3
4
Press SEL.  
Tuning in to a preset station  
Set the time you wish the unit to turn on.  
• Press TUNEi and turn the Smart Jog to set the hour.  
• Press TUNEk and turn the Smart Jog to set the  
minute.  
1
2
Press FNC repeatedly to select the desired band  
(FM1, FM2, FM3, AM1 or AM2).  
Press the preset station button on which the desired  
station is stored.  
5
6
7
Press SEL.  
Press FNC to select the band.  
PressTUNEi,TUNEkorthedesiredpresetstation  
button to select the station.  
Active tuning reception control (ATRC)  
The unit automatically suppresses FM noise caused by  
vehicle movement, and maintains sound quality.  
8
9
Press SEL.  
Set the time you wish the unit to turn off following the  
same procedure used in step 4.  
Using the timer  
(My Information)  
10 Press and hold INFO until the unit turns off, and  
setting is completed.  
You can schedule the radio to activate for daily radio  
programs. The unit automatically turns on and off in  
Radio mode at the scheduled times.  
When the unit is on, “MY INFO” appears in the  
display indicating that the unit is standby for a timer.  
During the timer-activated tuning, “MY INFO”  
continues to flash.  
To cancel the timer standby, press INFO so that  
“MY INFO” disappears.  
Note  
• To discontinue the timer setting, press and hold PWR/  
MUTE until the unit turns off.  
• To check the setting, turn off the unit, then pressINFO.  
The unit displays the scheduled turn-on and turn-off  
times with the appropriate radio frequency.  
• The unit automatically starts tuning at the scheduled  
time regardless of the current source mode. When the  
scheduled program is over, the unit automatically  
returns to the former source mode.  
• Timer setting remains enabled even if you turn off the  
unit, and then turn it on.  
• However, ifyoupressFNCtochangethesourcemode  
during timer-activated tuning, the scheduled program  
is canceled.  
ENGLISH 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Intro Play  
CD PLAYER OPERATION  
You can locate a desired track by monitoring the first 10  
seconds of all the tracks on a CD.  
Playing a CD  
1
Press INT during CD play.  
“SCAN” appears in the display.  
You can play CDs, CD-Rs and CD-RWs using the  
procedure described below.  
2
Press INT again when the desired track is played.  
The unit returns to normal CD play.  
One track Repeat Play  
You can play a track repeatedly.  
1
Press REP1 during CD play.  
“REPEAT1” appears in the display.  
To cancel One track Repeat Play, press REP1 again.  
Random Play  
You can play all the tracks in random order.  
1
Insert a CD.  
1
Press RNDM during CD play.  
“CD” appears in the display.  
“RANDOM” appears in the display.  
CD play starts.  
To cancel Random Play, press RNDM again.  
If a CD is already inserted, press FNC repeatedly to  
select CD play mode.  
In normal play, when the last track finishes, the unit  
returns to the first track and continues to play.  
Note  
During Random Play, pressing r allows you to skip  
only to the beginning of the current track, not to the  
previous track.  
Labeled-side up  
AUXILIARY EQUIPMENT  
Listening to a cassette/MD/MP3 portable  
player or other equipment  
CD indicator  
Track number  
Youcanlistentoequipmentconnectedtotheunit. Refer  
to the operating instructions for the corresponding  
equipment for more detailed information.  
Be sure to remove inserted CDs to prevent possible  
damage to the unit before connecting the equipment.  
Elapsed playing time  
To  
Press  
z
Eject a CD  
Skip to the next track  
t
r
Go back to the beginning  
of the current track  
AUX IN jack  
Each extra press skips  
backward one extra track  
1
2
Connectacassette/MD/MP3portableplayerorother  
equipment via the unit’s AUX IN jack (3.5 mm).  
Press FNC repeatedly until “AUX” appears in the  
display.  
Locate a specific point in Press and hold r or  
a track  
t until you find the  
point.  
During AUX mode, the clock display appears.  
Note  
• When you play a CD that is already inserted, CD play  
starts at the point where it stopped the previous time.  
A newly inserted CD starts from the first track.  
• A CD-R or CD-RW may take some time to start playing  
back, but this is not a malfunction.  
• If a CD-R or CD-RW with no data or incompatible data  
is inserted, “E03” will appear in the display. The unit  
cannot play such discs.  
5 ENGLISH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
SPECIFICATIONS  
RADIO SECTION  
(FM)  
Frequency Range: 87.5 MHz – 108 MHz (100-kHz  
steps)* or 87.5 MHz – 108 MHz (50-kHz steps)*  
Usable Sensitivity: 12.7 dBf  
50 dB Quieting Sensitivity: 17.2 dBf  
IF Rejection: 80 dB  
Error code  
In the following cases the corresponding error code  
indication appears. Follow the suggestions below to  
solve such problems. If the error code indication does  
not disappear, consult an AIWA service center.  
E03 Focuserror.CheckthattheCDisloadedproperly  
(right side up, etc.), and the CD contains valid  
data.  
Frequency Response: 30 Hz – 15,000 Hz  
S/N Ratio: 63 dB  
Stereo Separation: 35 dB at 1 kHz  
Alternate Channel Selectivity: 70 dB  
Capture Ratio: 3 dB  
Reset button  
IfaCDdoesnotoperateproperly, presstheresetbutton  
with a pointed object such as a pencil, etc. Note that all  
your settings will be erased if this button is pressed.  
(AM)  
Frequency Range: 530 kHz – 1,710 kHz (10-kHz  
steps)* or 531 kHz – 1,602 kHz (9-kHz steps)*  
Usable Sensitivity: 30 µV (30 dB)  
Reset button  
* Set the frequency increment for your area using  
the switch on the bottom of the unit. (The switch  
is factory-set to the 10k position [for the U.S.A.])  
CD SECTION  
Frequency Response: 17 Hz – 20 kHz +0/–3 dB  
Dynamic Range: More than 80 dB  
Channel Separation: More than 65 dB  
S/N Ratio: More than 85 dB  
MAINTENANCE  
Cleaning the front panel  
Wipe the surface with a soft, dry cloth.  
Wow/Flutter: Not applicable  
AUDIO SECTION  
Max. Power Output: 45 W × 4 channels  
AUX IN input  
Input sensitivity (load impedance) AUX IN: 300 mV  
(10 k)  
GENERAL  
Power-Supply Voltage: 14.4 V (11 to 16 V  
allowable), DC, negative ground  
Load Impedance: 4 Ω  
Tone Control:  
Bass ± 10 dB at 100 Hz, Treble ± 10 dB at 10 kHz  
Preamp Output Voltage (load impedance): 2.2 V  
(10 k)  
Installed size: 182 (W) × 53 (H) × 155 (D) mm  
(7 1/4 (W) × 2 1/8 (H) × 6 1/8 (D) inches)  
• Specifications and external appearance are subject to  
change without notice due to product improvement.  
REAR PANEL  
ENGLISH 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8B-KCH-901-01  
000914ATM-OX  
Printed in Indonesia  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Abocom Network Card UFE1000C User Manual
ADC Power Supply Power Distribution Products User Manual
Advantech Laptop PPC S123 User Manual
Agri Fab Spreader 45 02882 User Manual
Alba Flat Panel Television L26M1 User Manual
AMD Computer Hardware XP K7S748 User Manual
Ask Proxima Projector A10+ User Manual
Audiovox Remote Starter 128 4246A User Manual
Aviom Musical Instrument A 16CS User Manual
Beko Ice Tea Maker BKK 2210 C User Manual