Agilent Technologies Webcam 34970 80010 User Manual

Agilent 34970A/Option 001  
Internal DMM Assembly  
Installation Instructions for 34970-80010 Retrofit Kit  
1 Discon n ect th e p ow er cor d .  
2 R em ove th e ou t er cover fr om t h e Agilen t 34970A.  
To remove the cover from the instrument, follow the procedures shown  
in chapter 6 of the 34970A Service Guide.  
3 Con n ect th e in ter n al DMM r ibbon cable to th e m ain cir cu it boar d.  
Connect the loose end of the grey ribbon cable to connector J202 on the  
34970A main circuit board (34970-66511). Press down firmly on the  
ribbon cable connector and secure the cable in place with the locking clips.  
Snap the Locking Clips over  
the top of the connector to  
secure the Ribbon Cable  
Ribbon Cable  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
4 In st a ll t h e in ter n a l DMM cir cu it boa r d in to th e ch a ssis.  
Position the internal DMM circuit board inside the instrument chassis  
by tilting it at an angle as shown below. Be sure to position the circuit  
board over the tabs in the chassis as shown. Then, lower the assembly  
into the chassis until it is parallel with the 34970A circuit board.  
5 Lock t h e in ter n a l DMM cir cu it b oa r d in p la ce.  
Slide the internal DMM circuit board to the left (toward the rear of the  
instrument) until it locks in place. You will hear a click when it is  
properly locked in place.  
Make sure that shield is locked  
in place behind this tab  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
9 Mod ify th e La belin g on t h e R ea r P a n el.  
If you originally ordered the 34970A without the internal DMM, a solid  
black circle should be visible above the rear-panel Opt. 001” label.  
After installing the internal DMM retrofit kit, be sure to draw an “X”  
through the black circle using a permanent marker as shown below.  
Internal DMM  
is NOT installed.  
2SWꢀꢁꢂꢂꢃ  
Internal DMM  
is installed.  
2SWꢀꢁꢂꢂꢃ  
10 R ep la ce th e ou t er cover on t h e Agilen t 34970A.  
To replace the cover on the instrument, follow the procedures shown in  
chapter 6 of the 34970A Service Guide.  
Ca libr a tion In for m a tion  
The internal DMM was calibrated before it was shipped from the factory  
(a calibration certificate is included). However, after installing the internal  
DMM, you will want to make sure that you run the Zero Adjustment  
procedure as outlined in chapter 4 in the 34970A Service Guide.  
The internal DMM is guaranteed to meet the instruments 1-year  
accuracy specifications.  
‹ꢀ&RS\ULJKWꢀ$JLOHQWꢀ7HFKQRORJLHVꢁꢀ,QFꢂꢀꢃꢄꢄꢅꢆꢇꢈꢈꢉ  
3ULQWHGꢀLQꢀ0DOD\VLD  
(GLWLRQꢀꢊ  
$SULOꢀꢇꢈꢈꢉꢀ (ꢈꢊꢈꢉ  
ꢀꢁꢂꢃꢄꢅꢆꢃꢅꢅꢇꢈꢀ  
Retrofit Instructions  
34970-90052  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Abocom Network Card UHL1000C User Manual
Abocom Network Card USM560 User Manual
AG Neovo Computer Monitor S 15V User Manual
Airlink101 Security Camera AIC600W User Manual
Amana Slow Cooker PGB58B User Manual
Atlantis Land Switch A07 ES4626 SFP User Manual
Atlona TV Cables AT COMP300SR User Manual
BB Electronics Computer Hardware UEC100M 4 User Manual
Beko Refrigerator V322 X User Manual
Beko Vacuum Cleaner BKS1215 User Manual