Quick Start
Guide
Simple Steps
To Get Your
Up and Growing
nts
Replace
Bulbs
Space•Saver 6 Model #s – 100602-BLK; 100602-WHT;
100602-SLR; 100603-BSS
Date Code:
Input Voltage: 120V, 60Hz, 1.5A
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Quick Start Assembly
(No tools required)
Unpack Your Space•Saver 6
A
B
Insert Lamp Arm
into Base
Push
Lamp Arm
Lamp Hood
(front view)
Lamp Arm
(back view)
down until
you hear
a“click.”
Deluxe B
Grow Bulbs (2)
Base
(back view)
Bowl
Lamp Arm
(back view)
Add
Nutrients
Replace
Bulbs
Seed Kit
Base
D
Plug Lamp Cord
into Lamp Hood
(front view)
Push Lamp Cord
firmly into socket in
Lamp Hood.
C
Insert Deluxe B Grow Bulbs
into Lamp Hood
Lamp
Cord
Lamp Hood
(bottom view)
Push straight in.
DO NOT TWIST BULBS!
remember to replace Grow Bulbs every 6 months.
Instructions continued on next Page
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Quick Start Assembly
(continued)
Place Lamp Hood
on Lamp Arm
E
F
Set Bowl into Base
Air Coupling
Center hands over
Lamp Arm and push
Lamp Hood down until
you hear a“click.”
Add
Nutrients
Replace
Bulbs
(front view)
Be sure that Bowl is securely seated
on Air coupling in Base.
(back view)
Moving Your Space•Saver 6
G
Use one hand to
grasp Lamp Arm.
nEED ADDITIonAl HElP?
For supplies and information, visit…
Add
Nutrients
Replace
Bulbs
Gently slide your Space•Saver 6 toward the
surface edge and place other hand under Base.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Place Your Garden
H
In: A 60-75°F
(16-24°C)
environment
(optimal)
Under: A space that
Near: A standard
electrical outlet, per
local regulations
allows 22”(56cm)
clearance for the full
height of raised lamp
On: A sturdy, water-
tolerant surface
(Metal surfaces may cause
noise due to vibration)
note: Do not place beneath
under-cabinet lights.
Away From
Reach of children and pets
Direct sources of heat (e.g., stove, furnace vents)
Direct sources of cold air (e.g., window drafts, A/C vents)
For Optimal Tending & Harvesting, Also Consider
Easy access to un-softened water
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Planting Your Garden
2
A
Add Water Using a Spouted Container
Water level indicator gradually changes from red to green as water is
added.Water level indicator is GREEN when Bowl is full.
Lift View Door
FILL TO
HERE
Amount of
Water To Be
Added:
3 quarts or...
2.8 liters
Fill to “Fill To Here”
(located below View Door)
Add
Nutrients
Replace
Bulbs
Use room temperature
municipal tap, bottled or
purified water. Do not use
well or softened water.
When additional water is needed, water level indicator will be Red. Add water
to raise level up to “Fill To Here” inside Bowl.
It is okay to add water up to “Fill To Here” before water level indicator turns red.
Plan Your Garden Layout
B
For best results plant Seed Pods labeled…
”Tall” – in Back or Front center openings (see diagram below)
”Medium” – in Front center or Back openings
”Short” – in Front Side openings
Back
Genovese Basil
(
Sprouts in 3-7 days)
Tall
Grow Surface
Use height information on Seed Pod
Label to decide where to place each
Seed Pod in Grow Surface.
note: location of Seed Pod in Grow Surface does
not matter if all plants are the same height.
Front Side
Front Side
Front Center
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Plant Your Garden
C
If you are planting…
Herbs or Flowers - arrange Seed Pods by plant height (see “Plan Your Garden Layout” on page 5).
Tomatoes or Peppers - place one Seed Pod in each Front Side opening and one Seed Pod in either Back
opening. Plant Spacers should be placed in Front center and remaining Back openings.
Green Beans or Salad Greens - place Seed Pods anywhere, all plants are the same height.
Master Gardener Kit - arrange Pods in Grow Surface according to plant height. Re-arranging may be required
as plants grow.
Create a Custom Garden – combine two AeroGarden 3 Seed Kits.
Important guidelines to consider when combining Seed Kits…
• Only combine kits from the same Series, e.g., flower with flower, herb with herb, etc.
• Consider plant height when combining Seed Pods from two 3-pod Seed Kits. Refer to “Plan Your Garden
Layout” on page 5, when deciding where to place Seed Pods in your Space•Saver 6.
• Use two nutrient tablets for each feeding.
– Use both individual Starting Nutrients from each 3-pod Seed Kit when planting your Space•Saver 6.
– All Other Feedings – use Growing Nutrients from one Seed Kit (2 at a time) until they are gone, then use
the other Growing Nutrients from second Seed Kit.
Insert Seed Pods into Grow Surface
openings. Check to see that…
• There is a Seed Pod or Plant Spacer in
every opening.
Seed Pod
Grow Surface
• Seed Pod Labels are facing forward for
easy identification.
™
Bio-Domes
Nutrients
Add
Nutrients
Replace
Bulbs
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Planting Your Garden
(continued)
2
Place Bio-Domes on Seed Pods
D
Bio-Dome
note: Do not remove Bio-Domes until seeds
have sprouted. nEVEr rEMoVE SEED
POD LABELS.
Place a Bio-Dome on
each Seed Pod.
Add
Nutrients
Replace
Bulbs
Add Starting Nutrient Tablets and Record Planting Date
E
Record Planting Date
Record the date you planted your Space•Saver 6 on the
front cover of the Guide that came with your Seed/Plant Kit.
Add 2 tablets*
from bag labeled
“Starting Nutrients”
directly into Bowl.
See "Add Nutrients" (Feed Garden - Basic Feeding) on page 11 of
this guide for additional feeding instructions.
Add
Nutrients
Replace
Bulbs
*When combining two AeroGarden 3 Seed Kits, be sure to use 2 nutrient
tablets when feeding your Garden (see “create a custom Garden” on
page 6).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting Your Garden
3
Plug Cord into Electrical Outlet
A
What will happen…
1
2
A green light on the Control Panel willl come on.
Grow Bulbs will come on.
Plug in
Look under Lamp Hood to see if both bulbs are lit.
If not, check to see if:
• Grow Bulbs are properly inserted into
Lamp Hood (see page 2, step1C).
• Lamp Cord is plugged into Lamp Hood
(see page 2, step1D).
•You are getting power through the
electrical outlet.
3
Air bubbles should be visible inside Bowl.
If not, check to see if:
• Bowl is securely seated on Air Coupling in Base (see page 3, step 1F).
Select Setting
B
Press SELECT button until you reach the type of plants you are growing (Salad Greens, Herbs, etc.)
Herbs
Salad
Greens
Add
Nutrients
Flowers
Add
Nutrients
Replace
Bulbs
Replace
Bulbs
24-Hour
Light
s
Live Plants
note: Depending on the plant type selected, your
Space•Saver 6 lights will automatically turn
on and off at pre-programmed intervals.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting Your Garden
(continued)
3
C
Your Light Timer
If You Would Like to Change the
Time of Day Your Lights Go Off...
See page 10.
Your Light Timer is Set To Start
Growing Your Plants...Starting now!
1
2
• Your lights will stay on for about 16 hours and will shut off for about 8 hours*.
• Your lights will come on every day at the time you plugged in your Space•Saver 6.
*Except when using “24-Hour light” setting (Elite models only, see below), which sets lights to be on for 24 hours.
Space•Saver 6 Elite“24-Hour Light”Setting
noTE: The “24-Hour light” setting is not recommended for
Flower or Vegetable plants – they require a daily dark period
to produce flowers.
The “24-Hour Light” setting allows you to override the
built-in light timer and keep the lights on 24 hours a
day. You can also customize the amount of light plants
receive by manually turning lights on and off using the
“Lights” button, or setting automatic on/off times, using
a standard light timer.*
Space•Saver 6 Elite – “24-Hour Light “ Setting
• Press and release“Select”until white light next to
“24-Hour Light”is illuminated.
Use the “24-Hour Light” setting when growing plants
that thrive with continual light and moisture, such as
leafy greens and some herbs.
• To exit “24-Hour Light”setting, simply push the“Select”
button.
* not included. If you use a light timer to turn lights on and off, the
nutrient timer and pump will stop whenever lights are oFF. Both
will start up again when lights turn back on.
For the more experienced gardener, the “24-Hour Light”
setting provides added flexibility when planting a
custom garden. You are no longer limited to the pre-
programmed light schedules associated with each plant
type (such as Vegetables, Herbs, etc.).
nutrient timer does not record the time elapsed when lights are
off. To ensure your plants are fed every 2 weeks, we recommend
keeping track of your feeding schedule on a calendar.
Add
Nutrients
Replace
Bulbs
24-Hour
Light
Select
Illuminated“24-Hour Light”
Once your Space•Saver 6 Elite is set on “24-Hour Light” setting, lights will remain on 24 hours a day. To shorten the
amount of time lights are on, quickly press and release “lights” button, and lights will turn off. lights will automatically
come back on within 12 hours – or, you can press and release the “lights” button again, to turn lights back on.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Personalize Your Light Timer
(optional)
Your Space•Saver 6 has lights and a built-in timer that automatically provide your plants with“sunlight”(about 16
hours) and“night”(about 8 hours). As long as your plants get this amount of light, it does not matter when the lights
*
are turned off. Many people find it convenient to have the lights go on in the morning and off at night to match
their own wake and sleep schedule.
*The exceptions to this are Flower & Vegetable plants. They require a daily dark period in order to produce flowers. If your plants will receive any room light
during the day (natural or artificial), we recommend setting your Space•Saver 6 lights to be on during the day.
5 Simple Steps...
To make this as easy as possible, you only need to set the time you want your Space•Saver 6 lights to go off (Off Time)
and your built-in light timer automatically sets the On Time...nothing more for you to do.
Do the following to set the time you want your lights to go off:
1
2
Decide when you want the lights to go OFF.
AT THAT TIME check that lights are on. If they are off, quickly press and release “Lights” button.
(Lights must be on to reset timer.)
3
With lights on, press and hold “Lights” button until the light next to the plant type you selected
starts blinking – about 5 seconds.
4
5
Release the button.
When blinking stops (about 9 seconds), the lights will go off and your lights are now set to go
off at this time every day.
You can reset your timer as often as you wish.
Blinking Light
(if you selected Herbs)
Blinking Light
(if you selected Herbs)
Herbs
Salad
Greens
Add
Nutrients
Flowers
Add
Nutrients
Replace
Bulbs
Replace
Bulbs
24-Hour
Light
Vegetables
Live Plants
Lights Button
Lights Button
In case of power failure, your Space•Saver 6 has a backup system that stores light, nutrient & replace bulbs timers and plant
selection settings. When power is restored, your Space•Saver 6 will go back to the Off-On cycle you have set.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Reminders About Your AeroGarden
Space•Saver 6 control Panel
SELECT
ADD NUTRIENTS (Feed Garden - Basic Feeding)
The number of hours lights are on and off
depends on which plant type is selected.
When “Add Nutrients” light illuminates (every 2 weeks),
add 2 nutrient tablets and fill Bowl with water up to “Fill
To Here.” Press “Reset” button to restart nutrient timer
and turn off light.
Add
Nutrients
Replace
Bulbs
LIGHTS ON/OFF
REPLACE BULBS
Use to occasionally override built-in light timer.
Once pushed, lights will stay off/on until the
next time built-in light timer is set to go
on/off. This will not affect the timing of your
light cycle and occasional use of this feature
will not harm your plants.
When light illuminates (after 6 months of use), it is time to
replace Deluxe B Grow Bulbs. Additional Grow Bulbs can be
retailer. After replacing Grow Bulbs, press “Reset” button to
restart grow bulb timer and turn off light.
Space•Saver 6 Elite control Panel
SELECT
ADD NUTRIENTS (Feed Garden - Basic Feeding)
The number of hours lights are on and off
depends on which plant type is selected. Use
“Select” button to reach “24-Hour Light” setting
(see page 9).
When “Add Nutrients” light illuminates (every 2
weeks), add 2 nutrient tablets and fill Bowl with water
up to “Fill To Here.” Press “Reset” button to restart
nutrient timer and turn off light.
Add
Nutrients
Replace
Bulbs
24-Hour
Light
LIGHTS ON/OFF
REPLACE BULBS
Use to occasionally override
built-in light timer. Once pushed,
lights will stay off/on until the
next time built-in light timer is
set to go on/off. This will not af-
fect the timing of your light cycle
and occasional use of this feature
will not harm your plants.
When light illuminates (after 6 months of
use), it is time to replace Deluxe B Grow Bulbs.
24-HOUR LIGHT
Additional Grow Bulbs can be ordered at
www.aerogardensupport.com or from
your retailer. After replacing Grow Bulbs,
press “Reset” button to restart grow bulb
timer and turn off light.
White light indicates
Space•Saver 6 Elite is on
24-Hour Light setting.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Reminders About Your AeroGarden (continued)
Raise Lamp Hood (lights)
As plants grow to 1-2” from lights, raise the Lamp Arm one notch at
a time. Be sure Lamp Arm is set at the lowest setting when you start
your AeroGarden.
1
2
Unplug Space•Saver 6 and remove Bowl from Base.
Locking Lever
Hold Lamp Arm where it connects to Lamp Hood with one hand.
With other hand, push in Locking Lever.
3
4
Release Locking Lever while pulling up on Lamp Arm.
Locking Lever will automatically click into next notch in Lamp Arm.
Replace Bowl on Base and plug in Space•Saver 6.
note: When lowering Lamp Hood, be sure to hold Lamp Arm
to avoid crushing plants.
When“Replace Bulbs” light on control Panel begins to
blink after 6 months of use…
• Unplug Space•Saver 6.
Add
Nutrients
• Remove old Grow Bulbs and carefully discard*.
IMPorTAnT: To avoid burning, be sure Grow Bulbs are cool before handling.
Replace
Bulbs
Replace
Bulbs
• Insert new Grow Bulbs into Lamp Hood.
• Plug in Space•Saver 6 and press and release “Reset”
button to restart grow bulb timer.
Space•Saver 6 Elite
control Panel
Space•Saver 6
control Panel
Early Grow Bulb Replacement
If you replace Grow Bulbs before “Replace Bulbs” light illuminates, be sure to
restart grow bulb timer as follows:
• Press and hold “Lights” button until white light next to your selected plant
type starts blinking – about 5 seconds.
• Release “Lights” button. Plant type selected light will continue to blink for
about 9 seconds. While plant light is still blinking…
• Quickly press and release “Reset” button. “Replace Bulbs” light will blink
once and plant selected light will stop blinking.
*Check with local recycling authorities for light
bulb recycling availability in your area.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Prepare For Your Next Garden
Cleaning Instructions for your Space•Saver 6
Use only water and mild soap when cleaning your Space•Saver 6 (except when Sanitizing - Step 6). Do not use
abrasive cleaners or run through the dishwasher.
When your Garden has completed it’s growing cycle…
1
2
Rinse Bowl and Grow Surface with
tap water. Repeat.
7
8
Unplug Space•Saver 6.
Grow Surface
Carefully remove Bowl and Grow
Surface from Base and bring to
a sink. Set Base and Lamp Hood
aside.
Towel dry Bowl and Grow Surface
before putting them back together
and setting them on Base.
9
If Grow Bulbs have been in use more
than 6 months, they should be re-
placed at this time (see page 12).
NEVER SUBMERSE BASE AND
CONTROL PANEL IN WATER.
3
4
Remove Grow Surface from Bowl
and place on a counter near sink.
Your AeroGarden is now ready for
replanting.
Empty contents of Bowl in sink.
Do not pour water on houseplants. Nutri-
ent mixture may be too concentrated for
them.
5
Remove Seed Pods and plants
from Grow Surface.
• Pull Seed Pods out of Grow Sur-
face openings.
Plant
Growth
Seed
Pod
• Throw away Seed Pods and plant
debris (plant growth and roots).
If you compost, plant debris can
be composted.
Roots
6
Sanitize Space•Saver 6.
• Fill Bowl ¾ full with water.
• Add ¼ cup (59ml) of chlorine
bleach.
• Let sit for 2 minutes.
• Using sanitizing water, wipe
Grow Surface and Bowl with soft
cloth or sponge.*
*Gloves recommended.
• Scrub underside of Grow
Surface with soft scrub brush to
remove any tangled roots.
• Empty bleach water from Bowl.
Bundle cord when furnishing is not in use.
!
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Prepare For Your Next Garden
(continued)
Replanting Your AeroGarden
If you have already grown a garden in your Space•Saver 6, please follow the instructions below to
reset the nutrient timer:
• Press and HOLD “Reset” button until red “Add Nutrients” light blinks (approximately 6 seconds).
• Release “Reset” button. “Add Nutrients” light will turn off.
• Your Space-Saver 6 is now reset. (In some cases you may see other lights blink as well. This is nothing to worry about.)
Add
Nutrients
Add
Nutrients
Replace
Bulbs
Replace
Bulbs
24-Hour
Light
Reset
Reset
Add Nutrient
Add Nutrient
More Reminders…
WATER LEvEL LOW
REMOvE BIO-DOMES
When indicator is RED, add water to “Fill To Here” below
When plants appear through the hole in
View Door.
the Seed Pod Labels, remove Bio-Dome and
discard or recycle.
Water level indicator gradually changes from red to green as water is
added. Water level indicator is completely GREEN when Bowl is full.
Water level Indicator
Grow Surface
View Door
14
Download from Www.Somanuals.com. All Manuals Search And Download.
U.S.CAUTION – You are cautioned that any changes or modifications not expressly approved in this manual could void your author-
ity to operate this equipment. noTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected; or, Consult the dealer or an experienced radio/TV technician for help.
To reduce the risk of electric shock, this furnishing has a
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
polarized plug (one blade is wider than the other). This
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still
ATTENTION: POUR ÉVITER UN CHOC ÉLECTRIQUE,
does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
PRÉSENTER LA LAME LARGE À LA FENTE LARGE ET
POUSSER JUSQU’AU FOND.
© 2008 AeroGrow International, Inc., Boulder, CO U.S.A. U.S. Patents Pending
5/7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|