Addonics Technologies Computer Hardware ADPEXC User Manual

ADDONICS TECHNOLOGIES  
ADPEXC (PCI-E to ExpressCard Controller)  
SPECIFICATIONS  
INSTALLATION  
Hardware Installations:  
·
·
Supports ExpressCard 34 and ExpressCard 54 form  
factors.  
Install into both standard height or low profile  
systems.  
Install in PCI-Express BUS  
1. Power OFF PC and remove its cover.  
2. Select an empty PCI Express slot and insert the  
PCIe controller card.  
3. Connect USB cable from USB host to on-board  
USB port.  
·
·
USB 2.0/1.1 connector and USB 5 pin header for  
USB host connection.  
HEADER CONNECTION GUIDES  
·
Spring eject mechanism for easy installation of  
ExpressCard  
·
·
·
Four onboard voltage indicators  
Maximum 2.5 Gbits/sec per port  
Hot swap support* - cards can be plugged and  
unplugged without system power-off or reboot.  
Compatible with Windows 2000, Windows XP,  
Windows 2003  
Diagram 1: On most motherboards, the USB  
header/pin-out consists of 9 pins arranged in 2 rows;  
and each header allows for 2 USB connections (i.e.  
USB1 and USB2). Normally, the pins for USB1 and  
USB2 are in separate rows.  
·
Diagram 2: Simply plug the connector onto the  
header, in such that; the wires are correctly  
connected to the appropriate pins (i.e. wire  
assignments and pin assignments are matched).  
On some motherboards, there is a NC pin in the  
USB header. You can connect the S-GND wire onto  
this pin. NC simply means "no connection" and NC  
pin is an "empty" pin.  
4. Makes sure to secure the bracket with a screw.  
5. Close the PC’s cover.  
Note: The PCI-E to ExpressCard Controller does not  
require any driver to be installed. It is when a device is  
plug into the controller that your system would detect  
that device and ask for a driver for the ExpressCard.  
*Hot swap or activating the controller requires one of the  
following conditions:  
·
ExpressCard device must be inserted into the PCI-E  
to ExpressCard controller prior to system boot up to  
activate the controller. Afterwards, ExpressCard can  
be removed or reinsert with the same or different  
ExpressCard  
Motherboard must have special hardware and the  
appropriate ACPI firmware incorporated into the  
BIOS. This firmware, in addition to handle the  
hardware, must also account for different OS  
capability. Windows 2000, Windows 2003, and  
Windows XP are all non PCI-E aware OS and will  
not support hot swap.  
TECHNICAL SUPPORT  
Addonics Technologies  
2466 Kruse Drive  
San Jose CA 95131  
Phone: 408 433-3899  
Fax: 408 433-3898  
·
Technical Support (8:30 am to 5:30 pm PST)  
Phone: 408 433-3855  
USB header connection  
on PCIe Controller  
USB header connection  
on motherboard  
Download from Www.Somanuals.com. All Manuals Search And Download.  

AEG Refrigerator SCS51400S0 User Manual
Agilent Technologies Yard Vacuum 11636B User Manual
AKG Acoustics Satellite Radio GB 40 User Manual
Altec Lansing Compact Loader MP450 User Manual
AltiGen comm Network Router 6 2008 4510 0001 60 User Manual
AOC Flat Panel Television A20S431 User Manual
ATK Motorcycles Motorcycle 450 Dirt Track User Manual
Atlona Telephone AT HDTX RSNET User Manual
ATN Inc Binoculars ATN PS 22 User Manual
Baby Trend Baby Accessories 1638CT User Manual