Addonics Technologies Computer Drive RTM25N335H User Manual

ADDONICS TECHNOLOGIES  
Model: RTM25N335H  
I. Removing Cover of RAID Tower Mini  
After RAID configuration, it is compatible with any SATA  
controller (RAID or non RAID). If you have configured individual  
drives, you need to connect the RAID tower to a port multiplier  
compatible eSATA host controller, if you plan to use eSATA  
connection.  
Loosen the 3 screws at the back of the tower  
using a Philips screwdriver by turning  
counter-clockwise. Separate the metal casing  
of the storage tower from the housing by  
lifting up the casing as shown on the photo.  
Software Installation for SiI4726 Manager  
A. From the CD start-up menu select SATA RAID Utilities >  
Other SATARAID Utilities > Windows 2000/XP/2003/Vista.  
B. Unzip the file SiI_4726_Manager_V4.0.0.9.zip on your drive.  
The folder name would be SiI4726.  
II. Installing drive into the RAID Tower Mini  
C. To install SiI4726 Manager, double click setup.exe  
Using 2.5” SATA hard disk drive, slide the drive into the drive  
bay. Close the front panel to secure the drive.  
In SiI4726 Manager, all the drives connected to the RAID Tower  
IV will show up.  
hard disk drive  
VI. Setting RAID on the HPM  
Using 3.5” SATA hard disk drives, slide the  
drive into the embedded drive bay and  
secure the drive to the bay with screws  
provided.  
For a complete User’s Guide of SiI4726 Manager refer to our  
website.  
Support > User Guides > SiI4726 Manager User Manual V.26  
SATA data cable  
SATA power connector  
Connect the internal SATA data cable to the  
data port of the hard drive then connect the  
15-pin SATA power connector to the power  
port on the hard drive.  
III. Connecting the power cable and RAID Tower Mini to the  
computer  
a. Connect the power cord provided from the wall outlet to the  
back of the RAID Tower Mini.  
b. Make sure the power is off (power LED light should be off)  
c. Connect the provided eSATA cable from the back of the  
RAID Tower to the eSATA controller card on the computer.  
We recommend connecting the eSATA port for best  
performance if this port is available on your computer.  
d. If eSATA connection is not available, connect the USB2.0 to  
eSATA adapter to the other end of the eSATA cable then  
connect the adapter to the USB port on your computer.  
IV. Power on/off control  
Turn on the power to the RAID Tower Mini by pressing the  
power button on the front. The power LED light should lit  
indicating the power is on.  
V. Sil4726 Manager Utility Installation  
Note: You need to install the SiI4726 Manager on your system to  
configure RAID sets.  
RAID configuration is programmed by connecting the hardware  
port multiplier:  
TECHNICAL SUPPORT  
Phone:  
Hours:  
Email:  
408-453-6212  
8:30 am - 6:00 pm PST  
via USB 2.0 connection (Addonics USB2.0 to eSATA  
adapter is provided)  
or to one of Addonics’ SATA controllers that has SIL3124 or  
SIL3132 chip set.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Aastra Telecom Telephone M6320 User Manual
Abocom Network Card WMG2503 User Manual
Adder Technology Network Router AVM208MP User Manual
ADTRAN Network Card D4 U RPM User Manual
Agilent Technologies Water Dispenser 4155B User Manual
Alpine Stereo Amplifier DVA 9965E User Manual
Altec Lansing Speaker VS4121BLK User Manual
Amana Microwave Oven RBG635T User Manual
Audiovox Remote Starter PRO 9051 User Manual
Avet Reels Fishing Equipment LX 6 3 User Manual