INSTALLATION GUIDE
ADAPTEC SCSI CARD 29320A
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Adaptec SCSI Card 29320A
1 Discharge any static electricity build-up before handling your
SCSI card by touching a grounded metal object (like the
exposed metal parts on the back of your computer).
Warning: Turn OFF power to the computer and disconnect
the power cord.
2 After you turn off your computer and unplug the power cord,
remove the cover from the computer.
3 Locate an unused 64-bit PCI/ PCI-X expansion slot and remove
the expansion slot cover. If the computer does not have a 64-bit
slot, you can install the card in a 32-bit PCI slot. The Adaptec
SCSI Card 29320A supports both 5V and 3.3V 64-bit slots. (The
expansion slot must be compliant with PCI Rev. 2.1 or PCI-X
Rev. 1.0 and must support Bus Mastering.) Save the slot cover
screw for use in Step 4.
Slot cover screw
Expansion slot cover
32-bit PCI slot
64-bit PCI slot
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Computers may have vertical or horizontal expansion slots.
Refer to your computer manual to locate the PCI/ PCI-X slots. If
your computer is a tower model, lay it on its side to allow for
easier installation of the Adaptec SCSI Card 29320A.
Warning: Be careful when inserting the Adaptec SCSI Card
29320A in a PCI slot. Some 32-bit slots will not
accommodate it, and the card may break if you force it into
the slot.
4 Insert the Adaptec SCSI Card 29320A in the 64-bit (or 32-bit)
PCI or PCI-X expansion slot; press down firmly until the card
clicks into place, then replace the slot cover screw. When
installed properly, the card should appear level with the
expansion slot, as shown below.
Setting Up SCSI Devices
There are several things you may need to do to your SCSI devices
before you connect them to the Adaptec SCSI Card 29320A:
■
■
■
Check the SCSI IDs
Set the termination
Connect the power cables
Since setup can vary from device to device, always refer to the
device’s documentation for specific instructions.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Following are some guidelines for setting SCSI IDs and termination
on your devices.
Check the SCSI IDs
The Adaptec SCSI Card 29320A and each device you connect to it
must have a unique SCSI ID number ranging from 0 to 15 on each
channel. No two devices on the same SCSI channel can have the
same SCSI ID.
The Adaptec SCSI Card 29320A is preset to ID 7 for each channel
and should not be changed. If you boot from a SCSI hard disk,
make sure the hard disk SCSI ID is set to 0. (Most SCSI hard disks
are preset to SCSI ID 0 at the factory.) The SCSI IDs for internal
devices are usually set with jumpers; SCSI IDs for external devices
are usually set with a switch on the back of the device.
Terminate the Ends
To ensure reliable communication on the SCSI bus, the device at the
end of each cable, or the end of the cable itself, must have a
terminator installed (or enabled). Terminators must be removed, or
termination must be disabled, on devices between the ends of each
cable.
Note: When connecting Ultra320/ 160 or Ultra2 SCSI devices,
the SCSI bus must be terminated either on the end of the cable
(with a permanent terminator) or with a separate terminating
connector. Ultra SCSI and earlier single-ended devices can
terminate the bus directly from the device. If you use an Ultra
SCSI terminator on an LVD Ultra320/ 160 and Ultra2 SCSI
bus, the SCSI devices will not operate properly. For this
reason be sure that you have the necessary Ultra320/ 160 or
Ultra2 cable and terminator before installing the Ultra320/ 160
SCSI devices.
Connecting SCSI Devices
You can connect a total of 15 LVD and/ or 15 SE SCSI devices to the
Adaptec SCSI Card 29320A. Before connecting devices, be sure to
review Setting Up SCSI Devices on page 3.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Internal Ultra320/160 and Ultra2 Devices
A special 68-pin internal LVD cable is needed to connect internal
Ultra320/ 160 or Ultra2 SCSI devices. If your cables are not marked,
you can identify most LVD cables as having twisted pairs of the flat
ribbon cable between the device connectors. Some cables are
laminated so that they lay flat. Internal LVD cables usually have a
terminator built into the end of the cable.
The Adaptec SCSI Card 29320A has one internal 68-pin LVD
connector and two internal SE connectors to which you can connect
internal SCSI devices, as shown in the figure on page 1.
Note: Adaptec recommends that you keep your Ultra320/ 160
and Ultra2 SCSI devices separate from your Ultra SCSI
devices. This allows the Ultra320/ 160 and Ultra2 SCSI
devices to transfer data at their maximum speed.
Follow these steps to connect your internal Ultra320/ 160 and
Ultra2 devices:
1 Locate a 68-pin internal LVD SCSI cable, which may have either
twisted wires or flat wires, shown as follows.
Nonterminated end
Terminated end
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Plug the nonterminated end of the cable(s) to the internal LVD
connector.
3 Plug the internal Ultra320/ 160 and Ultra2 SCSI devices to the
other cable connectors, starting with the connector at the
terminated end of the cable.
Ultra320/160 or Ultra2
SCSI devices
Built-in terminator on cable
Plug first device to
this connector
Note: Internal Ultra320/ 160 and Ultra2 SCSI devices come
from the factory with termination disabled and cannot be
changed. Proper termination is provided by the terminator
at the end of the LVD SCSI cable.
4 Connect a power cable from your computer’s internal power
supply to each internal SCSI device.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Wide SCSI Devices
Connect internal Wide SCSI devices to the 68-pin internal SE Wide
SCSI connector. To do this, use a 68-pin Wide SCSI cable like the
one shown in Step 1 below. Follow these steps to connect the
devices:
1 Locate a 68-pin internal Wide SCSI cable.
2 Plug one end of the cable to the Wide SCSI connector on the
Adaptec SCSI Card 29320A.
3 Plug the other end of the cable to a terminated Ultra/ Fast Wide
SCSI device.
4 If you have other Ultra/ Fast Wide SCSI devices, attach them to
the connectors between the two ends of the cable. Be sure these
other devices are unterminated.
5 Connect a power cable from your computer’s internal power
supply to each internal device.
Connecting Internal Ultra/Fast Narrow Devices
Connect internal Ultra/ Fast Narrow SCSI devices that have
standard 50-pin connectors to the 50-pin internal SE Narrow SCSI
connector. To do this, use a 50-pin internal Ultra Narrow SCSI
cable. Follow these steps to connect the devices:
1 Locate a 50-pin internal Ultra Narrow SCSI cable.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Plug one end of the cable to the 50-pin internal SE Narrow SCSI
connector on the Adaptec SCSI Card 29320A.
3 Plug the other end of the cable to a terminated Ultra/ Fast
Narrow SCSI device.
4 If you have other Ultra/ Fast Narrow SCSI devices, attach them
to the connectors between the two ends of the cable. Be sure
these other devices are unterminated.
5 Connect a power cable from your computer’s internal power
supply to each internal device.
Connecting External SCSI Devices
You can connect external Ultra320/ 160 and Ultra2 SCSI devices to
the 68-pin external LVD SCSI connector. Each external device will
require a 68-pin LVD external LVD SCSI cable.
Note: We recommend that you do not combine older SCSI
devices with the newer Ultra320/ 160 and Ultra2 SCSI devices
on the same SCSI channel of the Adaptec SCSI Card 29320A.
Follow these steps to connect your external SCSI devices:
1 Connect one end of an external SCSI cable to one of the external
Ultra320/ 160 connectors on the Adaptec SCSI Card 29320A.
68-pin external
LVD SCSI connector
External LVD SCSI
cable
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connect the other end of the cable to a SCSI connector on the
back of an external device. If you are installing only one
external device, terminate the device and skip to Step 4.
SCSI terminator
3 Connect the other external SCSI devices by linking each device
to the previous one, as shown below. Terminate only the device
at the end of the chain.
4 Connect power cables to all external device(s) and to the
computer.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
More Information About Termination
The last SCSI device on the end of each SCSI bus cable must be
terminated, and termination must be disabled for all other devices
in the middle of the cables. Ultra320/ 160 and Ultra2 SCSI devices
are automatically unterminated, but Ultra SCSI and Fast/ Wide
SCSI devices do have termination that you must check. For more
information, refer to the documentation for each SCSI device.
If you are using external Ultra2 or Ultra320/ 160 devices, be sure to
use an LVD terminator to terminate the last device in the chain. If
you use a single-ended, active terminator (sometimes called an
Ultra terminator) the SCSI devices will not operate properly.
Troubleshooting
If you have any problems while installing the Adaptec SCSI Card
29320A, check the following items first:
■
■
■
■
Are all SCSI devices powered on?
Are all SCSI cables and power cables properly connected?
Does each device on each SCSI bus have a unique SCSI ID?
Does the total SCSI cable length exceed the maximum allowable
length?
■
Is the SCSI bus properly terminated?
If you are still unable to resolve a problem, contact the system
manufacturer for help.
Adaptec SCSI Card Driver Software
Note: To use the Adaptec SCSI Card 29320A, driver software
must be installed for your operating system. Installation of
the driver software varies depending on how and where you
purchased the Adaptec SCSI Card 29320A.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Preloaded Adaptec Drivers
If the Adaptec SCSI Card 29320A was included as part of a
computer system you purchased, the system already has the
appropriate Adaptec driver preinstalled by the computer
manufacturer. No further action is necessary to install the driver.
Embedded Adaptec Drivers
Some operating systems have embedded driver support for the
Adaptec SCSI Card 29320A. To determine if the card is supported
by the operating system you are using, read the operating system
manual or contact the operating system vendor for information.
Copyright
© 2003 Adaptec, Inc. All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, recording or otherwise, without the
prior written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035.
Trademarks
Adaptec, and the Adaptec logo are trademarks of Adaptec, Inc., which may be
registered in some jurisdictions.
All other trademarks are the property of their respective owners.
Changes
The material in this document is for information only and is subject to change
without notice. While reasonable efforts have been made in the preparation of this
document to assure its accuracy, Adaptec, Inc. assumes no liability resulting from
errors or omissions in this document, or from the use of the information contained
herein.
Adaptec reserves the right to make changes in the product design without
reservation and without notification to its users.
Disclaimer
IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE
PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID
VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER
REMEDIES.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Statements
Federal Communications Commission Radio Frequency Interference Statement
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. However, if this
equipment does cause interference to radio or television equipment reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
■
■
■
Reorient or relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
■
■
Consult the dealer or an experienced radio/ television technician for help.
Use a shielded and properly grounded I/ O cable and power cable to ensure compliance of
this unit to the specified limits of the rules.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Adaptec, Inc.
Adaptec SCSI
Card 29320A
Tested to Comply
With FCC Standards
FOR HOME OR OFFICE USE
European Union Compliance Statement
This Information Technology Equipment has been tested and found to comply with
EMC Directive 89/ 336/ EEC, as amended by 92/ 31/ EEC and 93/ 68/ EEC, in
accordance with:
■ EN55022 (1998) Emissions
■ EN55024 (1998) Immunity:
– EN61000-4-2 (1998) Electrostatic discharge: ±4 kV contact, ±8 kV air
– EN61000-4-3 (1998) Radiated immunity
– EN61000-4-4 (1995) Electrical fast transients/ burst: ±1 kV AC, ±0.5 kV I/ O
– EN61000-4-5 (1995) Surges ±1 kV differential mode, ±2 kV common mode
– EN61000-4-6 (1996) Conducted immunity: 3 V
– EN61000-4-11 (1994) Supply dips and variation: 30% and 100%
In addition, all equipment requiring U.L. listing has been found to comply with EMC
Directive 73/ 23/ EEC as amended by 93/ 68/ EEC in accordance with EN60950 with
amendments A1, A2, A3, A4, A11.
Australian/New Zealand Compliance Statement
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to the Australian/ New Zealand standard AS/ NZS 3548 set out by
the Spectrum Management Agency.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Canadian Compliance Statement
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur
le matériel brouilleur du Canada.
Japanese Compliance (Voluntary Control Council Initiative)
This equipment complies to class B Information Technology equipment based on
VCCI (Voluntary Control Council for Interface). This equipment is designed for home
use but it may causes radio frequency interference problem if used too near to a
television or radio. Please handle it correctly per this documentation.
R
Adaptec, Inc.
691 South Milpitas Boulevard
Milpitas, CA 95035 USA
© 2003 Adaptec, Inc.
All rights reserved. Adaptec and the Adaptec logo
are trademarks of Adaptec, Inc. which may be
registered in some jurisdictions.
Part Number: 513658-06, Ver. AA JG 08/03
Download from Www.Somanuals.com. All Manuals Search And Download.
|