ACCUSPLIT®
EAGLE™ 1520M2
MEMORY PEDOMETER
OPERATING INSTRUCTIONS
Congratulations on taking the first step to wellness with your purchase of an
ACCUSPLIT pedometer. It’s easy to set up your new pedometer.
Just follow the steps below, and start walking!
WEARING YOUR PEDOMETER
DISPLAY MODES
• “D”– “Day’s Steps”
Counts steps taken since last ReSet. Reset daily
to count each day’s steps.
• “t”–”total StepS”
While gently holding the belt clip open, slide the pedometer
onto your belt or the top edge of your pants or skirt. It should fit
snugly and level, above one knee.
Note: The pedometer should be as vertical as possible. Walkers
with larger stomachs may find it helpful to wear the pedometer
farther back on the body, toward one hip.
The cover must be closed for the pedometer to work. To
avoid losing or dropping your pedometer, use the included leash
and clip to fasten the pedometer securely to your clothing.
Keeps track of all steps taken, even after Day’s
Steps are reset.
ACCUSPLIT EAGLE
1520M2
“D”=Day
“T”=Total
D
T
STEP
Attaching the Leash: Attach the pedometer to the leash by
looping the leash around the pedometer belt clip. Next, loop the
leash through the enclosed plastic clip, then clasp the waistband
of your clothing with the clip. You can also use a safety pin to
fasten the leash to your clothing, loop the leash through your
belt or belt loop or use a badge holder.
99
TW15G
AccuSTEP 10000.org
RESET (2S) MODE
MODE and RESET button
First, loop the
pedometer clip
RESETTING YOUR PEDOMETER
Most people prefer to reset step counts daily. To reset: While
displaying Day’s STEPs, press and hold MODE button for at
least three seconds to reset to zero. When displaying Total
STEPs, press MODE button for three seconds to reset Total and
Day’s STEPs to zero.
Next, loop the metal clip,
then clasp clothing
AUTO MOVEMENT SENSOR
1. To filter out random movements, the unit remains in standby
mode until 5 continuous steps are registered. Only then are
the 5 steps calculated in, and an Active indicator “▲” appears
on the upper left of display.
Or, loop a belt or
belt loop
Or, loop a
badge holder, then
put into pocket
(Badge holder not included)
2. When regular walk/run movement stops, after 2 seconds the
timer pauses and the unit switches to standby status (Active
indicator “▲” disappears).
VIEWING YOUR RESULTS
Once you put on your pedometer with the cover closed, it will
automatically begin to record your steps. Repeatedly press the
yellow MODE button to cycle through the pedometer modes:
DAILY STEPS→TOTAL STEPS→DAILY STEPS
REPLACING THE BATTERY
When the display starts to dim or goes blank, it is time to replace
the battery. Your pedometer uses one Type LR44 1.5 volt alkaline
battery. To replace:
1. Insert a coin into the slot on the bottom of the case, and twist
counterclockwise to loosen the case front. Lift case front away.
REGISTER NOW Please return
your 1520M2 Registration to the
Repair Center address in the
warranty, and we will let you
know about future products.
Email (preferred)
User
2. Using a pen or other thin object, push battery sideways out of
its holder. Replace it with a new battery. The battery’s positive (+)
terminal should be FACE UP while you put it into the pedometer.
3. Align case front over the pedometer and press gently to snap
cover back into place, starting with top.
NO-PROOF-OF-PURCHASE LIMITEDWARRANTY
Eat Right! Walk More! Live Well!
e ACCUSPLIT Lifetyle
See label inside the lid of the pedometer.
ACCUSPLIT, Inc. • 2290M Ringwood Ave. • San Jose, CA 95131
970-044
Download from Www.Somanuals.com. All Manuals Search And Download.
|