Abocom Network Card M73 APO08 420 User Manual
USB  
10/100M  
FAST ETHERNET  
Quick Installation Guide  
M73-APO08-420  
Download from Www.Somanuals.com. All Manuals Search And Download  
INTRODUCTIONS  
The USB 10/100M Fast Ethernet Adapter  
provides outside-the-box plug-and-play local  
area network connections for USB-enabled PCs,  
notebooks and laptops. This adapter uses a B  
type USB port to connect with the USB host, and  
an RJ-45 port to connect with a 10/100 Fast  
Ethernet LAN link. Installation is easy and no  
external power is required! The network sharing  
is easier than ever.  
Specifications  
Network standard  
ꢀ
ꢀ
IEEE 802.3 for 10BaseT  
IEEE 802.3u for 100BaseTX  
Data Rate  
ꢀ
ꢀ
10/100 Mbps1  
Double data transfer rate in full duplex  
mode  
Supported operating systems  
Windows 98/2000/ME/XP  
Physical  
ꢀ
ꢀ
ꢀ
ꢀ
Ports: 1 RJ-45, 1 USB B-Type  
LED indicators: Link, Transmit/Receive  
Dimensions: 2.7”x 2” x 1” (LxWxH)  
1 CAT5 cable is required for 100M data transfer rate  
- 1 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
 
Parts Names and Functions  
ꢁUSB Connection Cable: connects the USB  
host port to the USB 10/100M Fast Ethernet  
Adapter.  
4
connects to the USB host port  
6
5
1
3
2
ꢂUSB-B Port: USB device port.  
ꢃUSB Fast Ethernet Adapter  
ꢄRx/Tx LED indicator: blinks green when the  
Fast  
Ethernet  
Adapter  
is  
transmitting/receiving data.  
ꢅLink LED indicator: glows green when  
100M Network is linked; when glows amber,  
then 10M Network is linked.  
ꢆNetwork Port: connects the Fast Ethernet  
Adapter to the HUB with the LAN cable.  
- 2 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
HARDWARE INSTALLATION  
Precaution  
Before the installation, make sure the USB port  
exists in your computer and is enabled. To check  
this,  
go  
to  
My  
ComputerꢇControl  
PanelꢇSystem. Open the Device Manager tab.  
If the Universal Serial Bus controller device is  
found, it means your USB port is installed and  
enabled. If not, either no USB port is installed or  
the USB bios is not properly enabled. In this  
case, consult your computer dealer for USB  
support.  
Getting Hooked Up  
1. Locate the USB host port of your system.  
Align the USB connector toward the USB host  
port, push evenly and steadily until it is seated.  
- 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
2. Connect another end of the USB connection  
cable to the device port (USB B) of your USB  
10/100M Fast Ethernet Adapter until it clicks.  
3. Connect the UTP cable to the Fast Ethernet  
Adapter.  
4. Connect the other end to a Hub.  
- 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
SOFTWARE INSTALLATION  
Installation for Windows 98  
1.  
Once the device is properly connected to  
your computer, Windows 98 will  
automatically detect the new hardware  
device. Perform the following procedures  
for installing the device driver.  
2.  
Insert the device driver disk into your  
floppy drive. When the above figure  
appears, click Next.  
- 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
3.  
The installation program will proceed  
automatically. Follow the on-screen  
instruction to finish.  
4.  
When Windows prompts you to restart  
your computer, click No to make some  
changes to your network settings.  
- 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
5.  
Go to Start ꢇSettings ꢇControl Panel.  
Double-click Network.  
6.  
7.  
When the Network dialog box appears,  
select USB 10/100M Fast Ethernet and  
click Add. Set the appropriate protocols  
and client for you needs. When completed,  
click OK.  
Remember to restart your computer to  
activate the new device  
Setup Diagnostics  
To verify if the device exists in your computer  
and is enabled, go to Start ꢇ Settings ꢇ  
Control Panel ꢇSystem. Click the Device  
Manager tab. If the 10/100 USB Network  
- 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
Adapter is found, it means that your device is  
properly installed and enabled.  
Installation for Windows 2000  
1. Once the device is well connected to your  
computer, Windows 2000 will automatically  
detect the new device. Click Next to  
proceed.  
- 8 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
2. Select Search for a suitable driver for my  
device (recommended) and click Next.  
3. Insert the new device driver to the disk drive.  
Select Floppy disk drives. Click Next.  
4. Click Next. Windows will copy all the  
necessary files to your system.  
5. Click Yes to continue.  
6. Click Finish to complete the software  
installation.  
- 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
7. Go to Start ꢇSettings ꢇControl Panel  
ꢇ Network and Dial-up Connections.  
Double-click Local Area Connections.  
8. When the Network dialog box appears,  
select USB 10/100 Network Adapter and  
click Install. Set the appropriate protocols  
and client for you needs. When completed,  
click OK.  
- 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
9. Remember to restart your computer to  
activate the new device.  
Setup Diagnostics  
To verify if the device exists in your computer  
and is enabled, go to Start ꢇ Settings ꢇ  
Control Panel ꢇSystem ꢇHardware. Click  
the Device Manager tab. If the USB 10/100  
Network Adapter is found, it means that your  
device is properly installed and enabled.  
Installation for Windows ME  
1. Once the device is well connected to your  
computer, Windows ME will automatically  
detect the new device. Select Specify the  
location of the driver (Advanced) and  
click Next.  
2.  
Insert the device driver disk into the floppy  
disk drive on your system. Select  
Removable Media (Floppy, CD-ROM…)  
and click Next to continue.  
- 11 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
3.  
Click Next to continue.  
4.  
Click Next. Windows will copy all the  
necessary files to your system.  
- 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
5.  
Click Finish to complete the software  
installation.  
6. When asked if you want to restart your  
computer, click No to continue the  
Network configuration.  
7.  
Go to Start ꢇSettings ꢇControl Panel.  
Double-click Network.  
8.  
When the Network dialog box appears,  
select USB 10/100 Network Adapter and  
- 13 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
click Add. Set the appropriate protocols  
and client for you needs. When completed,  
click OK.  
9.  
Remember to restart your computer to  
activate the new device.  
Setup Diagnostics  
To verify if the device exists in your computer  
and is enabled, go to Start ꢇ Settings ꢇ  
Control Panel ꢇSystem. Click the Device  
Manager tab. If the USB 10/100 Network  
Adapter is found, it means that your device is  
properly installed and enabled.  
Installation for Windows XP  
1.  
Once the device is well connected,  
Windows will detect the new device and  
prompt you to insert the network device  
driver. Click Install from a list or  
specific location… and click next.  
- 14 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
2.  
Insert the device Driver Disk into the  
floppy disk drive of your system. Select  
Search removable media (floppy, CD-  
ROM…) and click Next.  
3.  
Click Next to continue.  
- 15 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
4.  
Windows will start searching for the  
appropriate driver for the installation.  
When the screen appears as below, click  
Continue Anyway to proceed.  
5.  
6.  
Wait for seconds while Windows copies  
the appropriate driver to your system.  
Click Finish. The software installation for  
this network device is now completed.  
- 16 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
7.  
Go to Start ꢇSettings ꢇControl Panel  
ꢇNetwork and Dial-up Connections.  
Double-click Local Area Connections.  
8.  
When the Network dialog box appears,  
select USB 10/100 Network Adapter and  
- 17 -  
Download from Www.Somanuals.com. All Manuals Search And Download  
click Install. Set the appropriate protocols  
and client for you needs. When completed,  
click OK.  
9.  
Remember to restart your computer to  
activate the new device.  
Setup Diagnostics  
To verify if the device exists in your computer  
and is enabled, go to Start ꢇControl Panel ꢇ  
System. Click the Device Manager tab. If the  
USB 10/100 Network Adapter is found, it  
means that your device is properly installed and  
enabled.  
- 18 -  
Download from Www.Somanuals.com. All Manuals Search And Download  

Abocom Switch HF1000 User Manual
ADC Cassette Player RMG User Manual
ADC Network Card UltraWAVE CDMA Pico BS Plus User Manual
Agilent Technologies Portable Generator E4438C User Manual
Aiwa CRT Television TV F2000u TV F2400u User Manual
Alto Shaam Oven 12 20 RTM User Manual
Athena Technologies Speaker AS 1C6 User Manual
Azden Microcassette Recorder WHDPRO User Manual
Behringer DJ Equipment B312A User Manual
Beko Oven GM 15120 DA PR User Manual