u s e r ` s g u i d e
AMERICAN
TECHNOLOGIES
NETWORK
CORP.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLICATION
use. The device consists of the objective lens assembly, eyepiece and the body. The body
contains an image intensifier tube assembly with an integrated high voltage power source and
the three volt battery housing. When installing the battery one should keep in mind that the
polarity of the battery should coincide with the diagram on the body next to the battery housing
cap.
Objective lens protective cover is intended to protect the objective lens from dust and
scratches. It also will act as a daylight filter, allowing you to test the scope in daylight or other
bright light situations. The pinhole in the center of the protective cover allows the user to check
the operation ability of the device in daylight conditions.
NOTE: Do not test the scope in daylight conditions even with the daylight filter/lens cap on for
more than ten (10) minutes.
OPERATION
• Take the monocular out of the case.
• Install the battery into the housing with the polarity order as shown on the scope. Battery
Type: 3 Volt Lithium, #CR123A .
• The Night Storm has a single switch button operation.
1 GEN. MODEL:
• Press the button to turn the unit on with the protective lens cover still attached to the lens. The
Infra-Red Illuminator will also automatically turn on. The green LED indicator represents the
light intensifier tube and the IR Illuminator power.
• Press the button again to turn the unit off.
2 GEN. AND 3 GEN. MODELS:
• Press the button to turn the unit on with the protective lens cover still attached to the lens.
The green LED indicator represents the light intensifier tube power.
• Press the button again to turn the Infra-Red Illuminator on. The red LED indicator will light up
instead of the green.
• Press the button for the third time to turn the unit off. The IR automatically will turn off also.
• Do not turn the unit on in the daytime without the protective lens cap on.
NOTE: You should see green glow in the eyepiece. You may notice a persistent green glow
for up to five (5) minutes after you have turned the unit off. This is normal for the 1st Gen Light
intensifier tube.
• Observe the scene and adjust the diopter for optimal image clarity. Focus the front lens until
the image and the grain are both sharp.
• You may now enter a dark environment or simply shut the lights off in order to darken the
room.
• Next, remove the lens cap/daylight filter. Adjust the front lens for distance of the focus. You
should not have to readjust the diopter.
• The front lens should be readjusted as you view objects at different distances.
NOTE: We suggest that you focus the diopter during daylight with the filter on.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INFRA-RED ILLUMINATOR
Infra-red (IR) illuminators, are common to night vision. The
IR light greatly enhances the performance of the Night Storm
while remaining almost totally invisible to the naked eye. The
IR illuminator on the Night Storm is located underneath the front
lens, next to the battery compartment.
It is important to remember that the IR illuminator is simply an
infra red light source, and like any light source, it may loose its
effectiveness over a great distance.
NOTE: The IR will automatically turn off when the unit’s main power
is turned off.
USING THE CAMERA ADAPTER
(OPTIONAL)
To use your Night Storm with a 35mm camera or camcorder you will need the following:
1) If you plan to use a camcorder, then your camcorder must have a MACRO feature. Most
modern camcorders today have a MACRO feature built-in.
2) If you plan to use a 35mm camera, you will need a MACRO lens. If you don’t have one, we
advise that you contact your local camera store.
3) You may or may not need a STEP-UP or STEP-DOWN ring in order to adapt the camera
adapter to your lens.
NOTE: The camera adapter comes with 37mm and 52mm threads. If you need other sizes your
local camera store should be able to help.
• Remove the rubber eyecup from the Night Storm
• Screw the camera adapter onto the front of the lens on your Video camera’s lens or your
35mm camera’s lens.
• Loosen the three set screws on the camera adapter.
• Place the camera adapter over the Night Storm’s eyepiece.
• Tighten the three set screws to fit snugly to the Night Storm’s eyepiece
• You may need to focus the 35mm camera or video camera in combination with the Night
Storm in order to get the sharpest possible image.
• We suggest that you find an open space to work in. Focus the Night Storm so that the scene
is at its sharpest. For best results you should disable the auto focus (if any) on either the 35mm
camera or the video camera and manually focus the 35mm camera or the video camera. Once
the image is sharp, then simply adjust the Night Storm’s front lens to change the focus.
*An important part to remember is that you are not taking a picture of an object that is far away
from you, but you are actually taking a picture of the phosphorous screen of the Night-Storm that
is only 2-3 inches away.
Screw
Joint ring
Camera adapter
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING THE EYEPIECE
You may need to clean the eyepiece of the Night Storm from time to time in order to guarantee
top performance. When you receive your Night Storm you should check for dust on the
eyepiece of the unit.
First you will need to remove the eyepiece. To do that you will need to initially loosen the 2
set screws that can be found on the base. Then unscrew the eyepiece counter-clockwise to
remove it.
NOTE: You do not have to remove the set screws completely, they are very small and easy to
misplace.
CAUTION: Use only Photographic lens cleaning tissue on these surfaces. Be careful not to
scratch or smudge any of these surfaces. When using compressed air to blow dust away, make
sure to avoid inverting the can while spraying. This can cause frozen propellant to exit the can,
which can cause serious problems with the glass and phosphor screen.
STORAGE AND CARE
• If the device is not to be us d for extended period of time (more than 10 days) remove the
battery.
• Avoid touching lenses. If fingerprints or traces of dirt or dust appear, clean their surface with
a Photographic lens cleaning tissue.
• Keep lens cap/daylight filter on when not in use.
• The Night Storm is not harmful to the user or the environment.
• Do not disassemble except to clean the front lens and eyepiece: it will void your warranty.
• Evaluate the monocular function by looking through it in a lit environment with the daylight
filter lens cap on. Never use in daylight without the daylight filter lens cap on.
• Never point the Night Storm at a bright light source.
• Adverse atmospheric conditions such as fog, smog or haze and a lack of ambient light (moon
or starlight) may diminish the effective viewing distance.
TROUBLESHOUTINGS
Q: Flashes, flickers or clicking occur while operating
S: If it occurs within the first five minutes of inserting new batteries, it is normal and the device
will resume normal operation soon thereafter. If it occurs for more than 10 minutes, contact for
service instructions.
Q: Dark spots on screen.
S: These are either cosmetic blemishes in the intensifier tube or dust particles.
Q: Screen becomes darker than at previous use.
S: Replace batteries. If problem persists, contact your dealer or other authorized service rep-
resentative for service instructions.
Q: Image not clear.
S: Adjust objective lens, and/or the eyepiece.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
• Great for hunting, camping, boating or surveillance
• Standard total darkness technology
• Automatic brightness control
• Built-in IR illuminator
• Manual focus
• Adjustable eyepiece
• High res. 1st Gen.+ or US 2nd Gen.+ or US 3rd Gen. intensifier tube
• Rugged and versatile design
• Light weight and comfortable
• Waterproof and floating
• Single switch button operation
• Superb 1.5x or 3.5x lens system
• Soft case
• Two year warranty (optional extended warranty).
SPECIFICATIONS
Magnification ................................ 3.5x ( 1.5x for LE version )
Intensifier tube.............................. High Res. 1st Gen.+ or US 2nd Gen.+ or US 3rd Gen.
Detection range ............................ 150m (1 Gen.); 250 (2 Gen.); 300 (3 Gen.)
Recognition range ........................ 100m (1 Gen.); 175 (2 Gen.); 225 (3 Gen.)
Lens system.................................. 50mm F1:1.2 (35mm F1:1.0)
FOV .............................................. 18° ( 20° )
Diopter adjustment ....................... ±5
Resolution .................................... Varies according to tube & Generation
Power supply ................................ One 3 Volt Lithium
Range of focus.............................. 3’ to
Controls ........................................ Digital
Battery life..................................... 10-20 hours
Dimensions................................... 162 x 50 x 90 mm (175 x 50 x 90 mm)
...................................................... 6.4”x2”x3.5” (6.5”x2”x3.5”)
Weight........................................... 0.4 kg / 9.5 oz
Operating temperatures................ -30°F to +110°F
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2 YEAR PRODUCT WARRANTY
This product is guaranteed to be free from manufacturing defects in material and workmanship
under normal use for a period of 2 (two) years from the date of purchase. In the event a defect that
is covered by the foregoing warranty occurs during the applicable period stated above, ATN, at its
option, will either repair or replace the product, and such action on the part of ATN shall be the
full extent of ATN’s liability, and the Customer’s sole and exclusive remedy. This warranty does not
cover a product (a) used in other than its normal and customary manner; (b) subjected to misuse;
(c) subjected to alterations, modifications or repairs by the Customer of by any party other than ATN
without prior written consent of ATN; (d) special order or “close-out” merchandise or merchandise
sold “as-is” by either ATN or the ATN dealer; or (e) merchandise that has been discontinued by the
manufacturer and either parts or replacement units are not available due to reasons beyond the
control of ATN. ATN shall not be responsible for any defects or damage that in ATN’s opinion is
a result from the mishandling, abuse, misuse, improper storage or improper operation, including
use in conjunction with equipment which is electrically or mechanically incompatible with or of infe-
rior quality to the product, as well as failure to maintain the environmental conditions specified by
the manufacturer. CUSTOMER IS HEREBY NOTIFIED THAT OPERATION OF THE EQUIPMENT
DURING DAYLIGHT HOURS OR UNDER ANY EXCESSIVE LIGHT CONDITIONS MAY PERMA-
NENTLY DAMAGE THE INTERNAL COMPONENTS OF THE UNIT AND SAID DAMAGE WILL
NOT BE COVERED UNDER THIS WARRANTY. This warranty is extended only to the original pur-
chaser. Any breach of this warranty shall be waived unless the customer notifies ATN at the address
noted below within the applicable warranty period.
The customer understands and agrees that except for the foregoing warranty, no other warranties
written or oral, statutory, expressed or implied, including any implied warranty of merchantability or
fitness for a particular purpose, shall apply to the product. All such implied warranties are hereby
and expressly disclaimed.
LIMITATION OF LIABILITY
ATN will not be liable for any claims, actions, suits, proceedings, costs, expenses, damages or
liabilities arising out of the use of this product. Operation and use of the product are the sole respon-
sibility of the Customer. ATN’s sole undertaking is limited to providing the products and services
outlined herein in accordance with the terms and conditions of this Agreement. The provision of
products sold and services performed by ATN to the Customer shall not be interpreted, construed
or regarded, either expressly or implied, as being for the benefit of or creating any obligation toward
any third party of legal entity outside ATN and the Customer; ATN’s obligations under this Agree-
ment extend solely to the Customer. ATN’s liability hereunder for damages, regardless of the
form or action, shall not exceed the fees or other charges paid to ATN by the customer or
customer’s dealer. ATN shall not, in any event, be liable for special, indirect, incidental or
consequential damages, including, but not limited to, lost income, lost revenue or lost profit,
whether such damages were foreseeable or not at the time of purchase, and whether or not
such damages arise out of a breach of warranty, a breach of agreement, negligence, strict
liability or any other theory of liability.
PRODUCT WARRANTY REGISTRATION
In order to validate the warranty on your product, ATN must receive a completed Product Warranty
Registration Card for each unit. Please complete the form below and immediately mail it to our
Service Center: ATN Corporation, 20 South Linden Ave., Suite 1B, South San Francisco CA 94080.
Products qualifying for warranty repair will be either repaired or replaced within 10 business days of
receipt of merchandise unless the customer is notified otherwise.
OBTAINING WARRANTY SERVICE
To obtain warranty service on your unit, take or send the product, postage paid, with a copy of your
sales receipt to our service center, ATN Corporation at the address noted above. All merchandise
must be fully insured with the correct postage; ATN will not be responsible for improper postage or,
missing or damaged merchandise during shipment.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
For customer service and technical support, please contact
American Technologies Network Corp.
North American Office
20 S. Linden Ave. Suite 1B, South San Francisco, CA 94080
phone: 800-910-2862, 650-875-0130; fax: 650-875-0129
European Office
phone: 44(0)870-0111286, fax: 44(0) 845-3349142
The following countries can use our
toll free number 00 800 9102-8620
Austria, France, Germany, Holland, Italy, Spain, Sweden, Switzerland
©2002 ATN Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
|