AMX Stereo Amplifier DAS AMP4 User Manual

Installation Guide  
Carbon XA Amplifiers  
Overview - Carbon XA Amplifiers  
Carbon XA Product Specifications (Cont.)  
Where more than one pair of speakers is required in a zone, Carbon XA  
amplifiers provide the extra power needed to drive up to 4 additional speaker  
pairs (FIG. 1). Use Carbon XA in backyards, large rooms or other zones where  
additional speakers are needed.  
Dimensions  
(HWD):  
Including feet and rear connectors:  
• 3 1/16” x 17” x 13 1/2”  
• 7.68cm x 43.18cm x 33.52cm  
Weight:  
25.75 lbs (11.68 kg)  
Connecting Carbon XA to a Mi-Series Audio Controller  
Connect the Carbon XA Amplifier to the Mi-Series Audio Controller via the Molex  
connector labelled “From Controller” on the rear panel of the Carbon XA.  
Connecting Matrix Keypads to the Carbon XA  
Connect Matrix Keypads to the Carbon XA Amplifier via the Molex connector  
labelled “To Keypad” on the rear panel of the Carbon XA (see FIG. 2).  
Molex Connector  
FIG. 1 Carbon XA Amplifiers - Front view (DAS-AMP4 shown)  
FIG. 2 provides a Molex Connector Legend  
Carbon XA Amplifiers provide extra output power to multiple pairs of speakers  
driven from one Mi-Series/Delta zone.  
The DAS-AMP8 is an 8-channel amp that supports an additional 4  
speakers pairs per unit (120V). The DAS-IAMP8 is a 240V version.  
The DAS-AMP4 is a 4-channel amp that supports an additional 2 speaker  
pairs per unit (120V). The DAS-IAMP4 is a 240V version for International  
usage.  
Left +  
DATA  
Right +  
Ground (-)  
FIG. 2 Molex Connector Legend  
Features  
Note: When stripping cable for use with the Molex connector, only strip away  
about ¼” (6mm) of the insulation from each wire. The complete assembly should  
not have more than 1/32” (1mm) of bare wire exposed from the bottom of the  
connector.  
Features common to all Carbon XA Amplifiers include:  
High-quality sound - delivers 60 watts of high-quality sound per channel.  
Expandable configuration - stack up to 3 Carbon XA units per zone to gain  
up to 12 additional speaker pairs (24 channels).  
Connecting Speakers  
Easy installation - Speaker Wire Technology makes installation simple  
using four conductor speaker wire.  
Non-SWT Speakers  
Each speaker has a Red (positive) terminal and a Black (negative) terminal.  
Connect the appropriate wire from the keypad to Red and Black terminals on the  
Left and Right speakers, as with any standard speaker installation.  
Integrates with both the Delta Series and Mi Series controllers, as well as  
the C, C-DT and EL Series speakers.  
Utilizes proprietary SWT - Speaker Wire Technology™  
SWT Speakers  
Product Specifications  
Matrix Audio SWT Speakers are different from any other speaker available on  
the market. They allow you to control a single zone of audio without a keypad  
being installed. Therefore, some different wiring practices must be considered  
for proper operation and control.  
Carbon XA Product Specifications  
Models Available: DAS-AMP4 (FG1102-01) 4-Channel Amplifier (120 V)  
DAS-IAMP4 (FG1102-02) 4-Channel Amplifier (240 V)  
DAS-AMP8 (FG1102-03) 8-Channel Amplifier (120 V)  
DAS-IAMP8 (FG1102-04) 8-Channel Amplifier (240 V)  
This is achieved by “daisy-chaining” from the first speaker to the second  
speaker. The main run of 16/4 from the controller will go directly to the first  
speaker in the zone.  
Configuration:  
Modular Design - configurable in single pairs:  
At the controller end, the wiring is left-to-right: L D G R with the screws of  
the connector facing up.  
• DAS-AMP8: Up to 4 stereo pairs (8 channels - 4 Ohm load)  
• DAS-AMP4: Up to 2 stereo pairs (4 channels - 8 Ohm load)  
• Stackable up to 2 Carbon XA units  
At the speaker end, refer to the labeling on speaker PCB to ensure the  
correct wiring.  
Stereo Output:  
• Dual mono amplifier stage design  
The labelling at both ends must match or the IR control will not work (i.e.: if you  
used the RED wire for the Left Audio labelled “L” at the zone output, you must  
use the RED wire for the pin labelled “L” on the speaker connector).  
• 60 watts per channel  
• THD+N at 1 Khz continuous .006%@ 8 Ohms  
• Each Carbon XA is capable of providing 480 watts @ 8 Ohms  
Be sure to screw the connector down to the speaker crossover board before  
installing and securing in the ceiling. This will ensure that the connector will not  
disconnect after installation.  
Control Options:  
• Matrix keypad  
• C-Series speakers using SWT  
Power:  
• 750W max (Average usage = 250W).  
• High current Torroidal power supply  
A single run of 16/2 must be run from the first speaker to the second speaker.  
Audio Switching  
Front Panel Components:  
When no audio is present, the Carbon XA amplifier will go into Standby mode  
and mute the speakers after about 5 seconds. When audio is sensed at the  
input, the device will un-mute the speakers and the volume may be controlled by  
the keypad or remote. The switch time between muting and un-muting is  
approximately 200 milliseconds.  
• Status LED Dual stage status LED:  
• Red in standby  
• Green when active  
Rear Panel Components:  
• Power Switch & The master power switch will remain in the ON position  
Receptacle  
normally.  
• Output 1-4:  
Euro-style connectors provide direct connection to speakers.  
• From Controller: SWT input port (connects to an Mi-Series Audio Controller)  
To Keypad:  
SWT output port (connects to Matrix keypad or interface)  
Black, Silver  
Available Colors:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   

Acnodes Computer Monitor APM5084 User Manual
ADIC Tool Storage 6 00025 01 User Manual
ADTRAN Network Card NxT1 HSSI V35 User Manual
Agilent Technologies Video Games 66319b User Manual
AKG Acoustics Microphone D12 VR User Manual
ATO Speaker System SCM50ASL PRO User Manual
Audiovox Car Speaker CE 100 User Manual
Barco Carrying Case HDX Series User Manual
BC Speakers Speaker 12 PL 32 User Manual
BC Speakers Speaker DE12 User Manual