AMX Network Router NXA KLB User Manual

Installation Guide  
NXA-KLB Kensington Lock Bracket for NXT-1200V and -VG Series Panels  
Securing locations for Kensington Lock Brackets  
Overview  
The NXA-KLB (FG2259-10) is an optional accessory for AMX Table Top (NXT-) 1200V  
and VG-Series touch panels, which allows you to use a standard Kensington Lock  
System to prevent theft.  
Connector plate cover (open to access the  
connectors on the rear of the base)  
The Kensington Lock System itself (including lock, key and security cable) is sold  
separately.  
The Kengsington Lock System is a security system from Kensington Technology  
Group (www.kensington.com) that discourages the theft of portable computers and  
other devices (in this case touch panels) by using a security cable and lock to anchor  
the panel to an object in the room. The security cable is looped through a permanent  
object in the room, then looped through itself and locked into the slot. Once secured in  
this way, the panel cannot be removed from its location unless it is unlocked (using the  
key that comes with the Kensington Lock assembly).  
The NXA-KLB Bracket attaches to the base of the Table Top 1200V and VG-Series  
panels (listed below) using keyed-lock securing screws that can only be removed with  
the included AMX Keyed-Lock screw driver adapter. This screwdriver head fits into  
most hex-type screwdrivers or electric drills.  
Touch Panel glass (facing down)  
Base plate  
There are two versions of the Bracket included with the kit, as indicated in FIG. 1:  
FIG. 2 Location of the securing locations on an NXT (Table Top) panel  
The Flat Lock Bracket fits neatly into the rear of the panel’s base, allowing you  
to close the rear connector plate cover on the base while the panel is secured.  
Method A: Installing the Raised Lock Bracket  
Note that once installed, the shape of the Raised Lock Bracket will not allow the  
Connector Plate Cover on the base of the panel to be closed.  
The Raised Lock Bracket also allows you to use the Kensington Lock System  
to secure the panel, while providing a surface to which you can secure incoming  
cables.  
1.  
Raise the Connector Plate Cover, and align the openings on the bottom of the  
Raised Lock Bracket to the securing locations on the Base Plate of the panel  
(FIG. 2).  
Raised Lock Bracket  
Kensington Lock/Security Cable  
assembly (not included)  
Keyed-Lock  
Securing Screws  
Connector plate cover  
Raised Lock Bracket  
AMX Keyed-Lock screwdriver adapter  
(fits into any standard hex-type  
screwdriver or drill)  
Keyed-Lock Securing Screws  
Flat Lock Bracket  
AMX Keyed-Lock screwdriver adapter  
FIG. 1 NXA-KLB Components  
Product Specifications  
NXA-KLB Specifications  
FIG. 3 Raised Kensington Lock Bracket Components and Installation  
2.  
3.  
Insert two Keyed-Lock Securing Screws into their respective locations (FIG. 3).  
Use the Keyed-Lock screwdriver adapter to tighten these screws, securing the  
Raised Lock Bracket to the base plate (FIG. 4).  
Compatible AMX  
Touch Panels:  
NXT-1200V, 12" Modero Video Table Top Panel (FG2250-60)  
NXT-1200VG, 12" Modero Multimedia Table Top Panel (FG2250-61)  
NXT-1500VG, 15" Modero Multimedia Table Top Panel (FG2252-61)  
NXT-1700VG, 17" Modero Multimedia Table Top Panel (FG2257-61)  
Kensington Lock/Security Cable  
assembly (not included)  
Requirements:  
The NXA-KLB must be used with a standard Kensington Lock System  
Note: The Kensington Lock System must be purchased separately, and is  
not provided by AMX.  
Thread incoming cables through this  
opening between the Bracket  
and the Base  
Included  
Accessories:  
Raised Lock Bracket (with cable tie down) (black)  
Flat Lock Bracket (black)  
AMX Keyed-Lock screwdriver adapter  
Keyed-Lock Securing Screws (5)  
Raised Lock Bracket  
Preparing the Touch Panel to Install the NXA-KLB  
1.  
Gently place the touch panel LCD facedown onto a soft cloth to expose the  
under-side of the base and prevent scratching of the LCD (FIG. 2).  
You may find it easier to handle the panel if you carefully detach all connectors.  
Securing locations  
Base Plate  
2.  
3.  
Tilt the base forward so that the bottom surface of the base is easily accessible.  
This provides access to the underside of the unit and exposes the securing loca-  
tion for the Kensington Lock Bracket (FIG. 2).  
Determine which type of bracket (Raised or Flat) you will be installing:  
If your installation requires secured cables, use the Raised Lock Bracket.  
FIG. 4 Raised Securing locations  
4.  
Thread the incoming cables through the opening between the bottom of the  
Raised Bracket and the Base Plate (FIG. 4).  
Reconnect the cables (on the rear connector plate).  
Thread a tie-wrap (not included) through the center pair of circular openings on  
the bracket (FIG. 5) and use it to secure all of the NXA-MTC/RGB cables to the  
bracket. Trim off any excess length on the tie-wrap (if necessary).  
If your installation requires a low-profile security solution, use the Flat Lock  
Bracket.  
5.  
6.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       

3Com Modem MIC 3365 User Manual
Acer Network Card 08P4100 User Manual
ADTRAN Network Card 3010 HTU C User Manual
Agri Fab Spreader 45 0288 User Manual
AlphaShield Network Card INTERNET PRIVACY PROTECTION User Manual
Alpine GPS Receiver NVE N852ADVD User Manual
AMCC Computer Accessories 9500S User Manual
Balance Scale 500KL User Manual
Beckett Water Gardening Outdoor Fountain CPPH16 User Manual
Beko Freezer DSE 28000 KL User Manual