Section 61109403L2-5
Issue 3, November 1997
CLEI Code: D4F1DFJ_ _ _
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
PRACTICES
HANDLING PRECAUTIONS REQUIRED.
2FXS/DPO PM
FOREIGN EXCHANGE STATION/DIAL PULSE ORIGINATE DATAPORT
WITH PERFORMANCE MONITORING
INSTALLATION AND MAINTENANCE
CONTENTS
1.
2.
3.
4.
5.
6.
GENERAL ...................................................................1
INSTALLATION...........................................................2
CONNECTIONS..........................................................4
TESTING.....................................................................4
MAINTENANCE ..........................................................5
SW 4
SW 3
SW 2
SW 1
2FXS/DPO
1109403L2
PM
WARRANTY AND CUSTOMER SERVICE ................5
AP
REM
FIGURES
PM
Figure 1. 2FXS/DPO...........................................................1
Figure 2. Circuit Path..........................................................3
Figure 3. Connector ............................................................4
TEST
BUSY
SW 7
TABLES
Table A. SW1 (Receive) and SW2 (Transmit) ...................2
Table B. SW3, SW4, and SW5 Option Settings ................2
Table C. Manual Configuration Guide................................3
Table D. Electronic Provisioning Settings ..........................3
Table E. 2FXS/DPO Faceplate Indicators .........................4
Figure 1. 2FXS/DPO
1. GENERAL
This practice provides installation and maintenance
information for the ADTRAN® Intelligent 2-Wire Foreign
Exchange Station/Dial Pulse Originate (2FXS/DPO PM)
Dataport with Performance Monitoring, part number
1109403L2. It is a D4 compatible channel unit and
operates in any standard D4 channel bank. Intelligent
featuresrequirestheunittobeusedintheADTRANACT
2300, ACT 1900 , or standard WECO® D4 channel bank
using the ADTRAN LIU-3/PM common unit. The 2FXS/
DPO PM provides an interface between a D4 channel
bankPulseCodeModulation(PCM)backplaneinterface
and a 2-wire voice frequency (VF) transmission and
signaling facility. Figure 1 is an illustration of the 2FXS/
DPO PM. The unit is multifunctional and can be
provisioned to operate in the following modes:
Using the FXS/DPO PM in an intelligent channel bank
provides additional features and functions such as:
• Local and Remote Provisioning using either the craft
interface or ADTRAN Site Manager through a menu
driven program called EASYMENU™
• Performance monitoring of the loop
• Network and customer side monitoring and analysis
• Enhanced Test Capabilities
Revision History
Revisions to this practice include CLEI code and dip
switch settings.
Features
• Backplane interface to the Pulse Code Modulation
(PCM) bus.
• On board coder/decoder (CODEC) uses µ-law
encoding/decoding.
• Nominal600ohmor900ohm2-WireVFinterfacewith
DC isolation.
• 2-Wire Foreign Exchange Station (2FXS)
• Dial Pulse Originate (DPO)
• Tandem FXS Mode
• Private Line Auto Ringdown (PLAR)
Trademarks: Any brand names and product names included in this document are trademarks, registered trademarks, or trade names
61109.403L2-5C
1
of their respective holders.
Download from Www.Somanuals.com. All Manuals Search And Download.
The trunk processing options are provisioned
only by switch SW7. Electronic provisioning is
not available.
Before provisioning the unit electronically, access the
channel unit by selecting:
Channel Unit Menus
Desired slot
(3)
(1-24)
(2)
Table C provides a guide to ensure proper provisioning
of the desired channel unit mode.
Provisioning
Select current operational mode
Select desired provisioning option (1-*)
(1-4)
Table C. Manual Configuration Guide
FXS
Loop
Start
X
FXS
Gnd
Start
X
TANDEM TANDEM
Loop
Start
On/Off
Gnd
Start
On/Off
Options
PLAR
DPO
For additional information on EASYMENU operation or
the ADTRAN Site Manager, refer to the EASYMENU
User Manual, document number 61150.055L1-1 (found
intheACT2300/1900SystemManual,document number
2150.050-3),ortheSiteManagerUserManual,document
number64150.075L1-1. Foradditionalinformationabout
the LIU-3/PM see the LIU-3/PM User Manual, part
number 61151.001L2-1.
RTG
On
X
(SW4-1)
DTG
X
X
X
X
On/Off
On/Off
On/Off
X
On/Off
On/Off
On/Off
X
X
X
X
X
(SW4-2)
TWS
(SW4-3)
TRB
X
X
X
X
(SW4-4)
PD3
X
X
On/Off
X
X
(SW4-5)
GS
Off
On
Off
On
X
Initial Turn-up
(SW4-6)
Refer to the desired operational mode in Table C for the
correct provisioning options.
DPC
On/Off
On/Off
Off
On/Off
On/Off
Off
X
X
X
X
(SW4-7)
SD
On/Off
On
On/Off
On
On/Off
Off
On
Off
Off
On/Off
Off
Off
Off
On
(SW4-8)
Transmit Attenuation
TNDM
(SW3-2)
DeterminetheinputTLP. Thenusethefollowingformula
to calculate the amount of transmit attenuation to add to
the circuit:
PLAR
Off
Off
Off
Off
(SW3-3)
FXS
On
On
Off
Off
(SW3-4)
DPO
Off
Off
Off
Off
Tx Attenuation=Input TLP + Internal Tx TLP of 4.5
dBm
(SW3-5)
Note: X = Switch position is ignored.
For example, if an input TLP level of -3 dB is to produce
a level of 0dBm0 at TLP0, then the Transmit Attenuation
should be set to 1.5 dB.
Electronic Provisioning
ADTRANEASYMENU isusedtoelectronicallyprovision
the unit. Connect a VT 100 terminal or a computer
running a terminal emulation program to the faceplate
ADMIN port or REMOTE port using a standard male-to-
male RS-232 cable. The settings for the ADMIN and
REMOTE ports are shown in Table D.
Receive Attenuation
Determine the output TLP. Then use the following
formula to calculate the amount of receive attenuation to
add to the circuit:
Rx Attenuation=Internal Rx TLP of 0 dBm) - Output
TLP
A null modem cable is required to connect the
REMOTE port directly to a terminal.
For example, if 0dBm0 at TLP0 is required to produce an
Output TLP level of -3 dB, then the Receive Attenuation
should be set to 3 dB. Figure 2 provides an illustration
of attenuation settings.
Table D. Electronic Provisioning Settings
ADMIN Port
9600 baud
No Parity
8 bits
REMOTE Port
SW2 baud
Settings
No Parity
8 bits
Transmit Path
Tx Atten
1 stop bit
1 stop bit
T
TDATA
0 dBm0
-4.5 to +1.8 dB
Input TLP
Onceconnected,enterthepassword. Thefactorydefault
password is PASSWORD in all capital letters. The
password may be changed by selecting:
0- 6.3 dB
Rx Atten
TLPO
0 to -6.3 dB
Output TLP
RNPCM
0 dBm0
R
0- 6.3 dB
TLPO
Common Module Menus
BCU
Configuration
(2)
(1)
(1)
(9)
Receive Path
Figure 2. Circuit Path
Read/Write Password
61109.403L2-5C
Section 61109.403L2-5, Issue 3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
When the option BOTH is selected, tone is placed on
both the loop and the network.
3. CONNECTIONS
The2FXS/DPOPMoccupiesonecardpositionintheD4
channel bank. The connector pin assignments are
detailed in Figure 3.
Accessing Tests Through EASYMENU
Once the unit is in normal operation, these test features
are accessed by selecting:
4. TESTING
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
1
FRM GND
-12V
12V GND
+12V
5V GND
TWD
TSP
TSQ
RNPCM
RFA
Channel Unit Menus
Desired slot
Test
(3)
(1-24)
(4)
2
The2FXS/DPOperforms
a self test after power on.
During this time all four
indicators turn On in a
predefined sequence
while the 2FXS/DPO
verifies proper operation
of critical circuits in the
design. After successful
completionoftheselftest,
all indicators function in
their normal mode.
+5V
3
4
5
6
These tests are service affecting.
7
TDATA
8
Faceplate Indicators
The 2FXS/DPO faceplate indicators and descriptions
are explained in Table F.
9
RFB
RCLK
RWD
RSQ
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
TDCLK
RSP
RNDIS
-48 FRT
Table E. 2FXS/DPO Faceplate Indicators
-48F
-48 SPRT
Indicator Indication
Description
2FXS/DPO
1109403L2
PM
REM
Off
Unit is manually provisioned.
Unit is remotely provisioned.
Configuration/provisioning error.
Green
Flashing
Digital Loopback Test
TheDigitalLoopbackTest
is used to test loopback
data coming from the
network. Received data,
or RNPCM, is latched in
during the appropriate
receive time slot. This
data is then placed on the
TDATA bus during the
unit's transmit time slot.
TFCC
AP
REM
PM
TEST
BUSY
IN
-48SD
R
PM
Off
PM mode is not operating.
PM mode is operating.
2N
T
Green
TEST
BUSY
Off
Yellow
All tests are inactive.
Test is active.
BT
20HZ
RT
RG
Off
Network and Loop On-hook.
Network, Loop, or both are Off-
hook.
Green
Switch Selection
Description
Figure 3. Connector
Pin Assignments
Alternate provisioning switch.
Changes provisioning source
from manual to remote or remote
to manual.
AP
Depressed
Network On-hook/Off-hook Test
The Network On-hook/Off-hook test is used to test
signaling sent to the network by the unit. When On-hook
Testisselected,On-hooksignalingissenttothenetwork.
When Off-hook Test is selected, Off-hook signaling is
sent to the Network. The customer loop is forced On-
hook while this test is active.
The 2FXS/DPO PM has four faceplate indicators and a
depressed provisioning switch. The front panel PM
(Performance Monitoring) indicator Flashes during
control link establishment and remains ON after the
channel unit has been remotely provisioned.
If the channel unit has been remotely provisioned, the
operatorcanalternatebetweentheremoteconfiguration
data stored in nonvolatile memory or manual switch
settings by pressing the momentary AP (Alternate
Provisioning) switch located on the front panel.
Customer Ringing Test
The Customer Ringing Test will activate the unit's ring
relay in a 2-on/4-off ring cadence, providing ringing to
the customer loop when a ring generator is properly
connected to the channel bank.
The REM indicator remains ON when the channel unit is
operating based on Remote Provisioning, and is OFF
when based on manual switches. If the channel unit has
never been remotely provisioned, the AP switch has no
effect and the REM indicator remains OFF . The REM
LEDFlasheswhenaninvalidoperationmodeisselected.
1004 Hz DRS Tone Generation Test
The 1004 Hz DRS (Digital Reference Signal) Tone
Generation test is used to send the DRS signal to the
network, loop, or both. When Network is selected, the
DRSissenttothenetworkfromtheunit. Thefarendunit
should measure a 1004 Hz tone at a level determined by
the circuit gain of the far end unit. When Loop is
selected, the DRS is placed on the receive path. The
loopreceivelevelisdeterminedbythefollowingequation:
Receive Level = 0dB - Attenuation
4
Section 61109403L2-5, Issue 3
61109.403L2-5C
Download from Www.Somanuals.com. All Manuals Search And Download.
5. MAINTENANCE
The ADTRAN 2FXS/DPO requires no routine
maintenance to operate properly.
ADTRAN recommends that repairs on the unit not be
performed in the field. Repair services may be obtained
by returning damaged units to ADTRAN (see section 6,
Warranty and Customer Service).
6. WARRANTY AND CUSTOMER SERVICE
ADTRAN will replace or repair this product within ten years
from the date of shipment if it does not meet its published
specifications or fails while in service (see ADTRAN
Equipment Warranty, Repair, and Return Policy and
Procedure).
Return Material Authorization (RMA) is required prior to
returning equipment to ADTRAN.
Forservice,RMArequests,orfurtherinformation,contact
one of the following numbers:
ADTRANTechnicalSupport..................(800)726-8663
Standard support hours,
Monday-Friday, 7am-7pm CST
Emergency Support:,
7 days/week, 24 hours/day
ADTRAN Sales ........................................(800) 827-0807
ADTRAN Repair/RMA .............................(205) 963-8722
Repair and Return Address
ADTRAN, Inc.
Customer Service Department
901 Explorer Boulevard
Huntsville, Alabama 35806-2807
61109.403L2-5C
Section 61109.403L2-5, Issue 3
5
Download from Www.Somanuals.com. All Manuals Search And Download.
|