®
MX410/MX412 System Manual
Document Number: 61189500L1-1B
August 2005
PRELIMINARY
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Revision History
Revision
Date
Description of Changes
A
B
June 2005
August 2005
Initial release
PPP and MX412 information added
Conventions
The following typographical conventions are used in this document:
This font indicates a cross-reference link. First-time references to tables and figures are
shown in this font.
This font indicates screen menus, fields, and parameters.
THIS FONT indicates keyboard keys (ENTER, ESC, ALT). Keys that are to be pressed simultaneously
are shown with a plus sign (ALT+X indicates that the ALT key and X key should be pressed at the
same time).
This font indicates references to other documentation and is also used for emphasis.
Thisfontindicates on-screen messages and prompts.
Thisfontindicates text to be typed exactly as shown.
This font indicates silkscreen labels or other system label items.
This font is used for strong emphasis.
NOTE
Notes inform the user of additional, but essential, information or
features.
CAUTION
Cautions inform the user of potential damage, malfunction, or dis-
ruption to equipment, software, or environment.
WARNING
Warnings inform the user of potential bodily pain, injury, or death.
61189500L1-1B
PRELIMINARY
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Compliance
The MX410 (P/N 1189500L1) and MX412 (P/N 1189512L1) comply with the requirements
covered under UL 60950 and NEBS Level 3. The MX410 and MX412 are intended to be
installed in a restricted access area only.
The MX410 and MX412 devices comply with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. The device may not cause harmful interference.
2. The device must accept any interference received, including interference that may cause
undesired operation.
Changes and modifications not expressly approved by ADTRAN could void the user’s authority
to operate this equipment.
WARNING
The V.35, Ethernet, terminal server, craft port, and FXS port (if
present) interfaces are not to be connected to outside plant (OSP)
facilities.
CAUTION
Per GR-1089-CORE October 2002, Section 9, this system is
designed and intended only for installation in a DC-C (common)
Bonding and Grounding system. It is not intended or designed for
installation in a DC-I (isolated) Bonding and Grounding system.
The ground wire must be of equal or greater ampacity than the wire
connected to the VDC return.
The Compliance Codes for the MX410/MX412 units and the MX410 Power Supply Unit (PSU)
are provided in the following tables.
Table 1. MX410 and MX412 Compliance Codes
Code
Input
Output
Power Code (PC)
F
X
A
C
X
–
Telecommunication Code (TC)
Installation Code (IC)
Table 2. MX410 Power Supply Unit Compliance Codes
Code
Input
Output
Power Code (PC)
F
–
C
–
Telecommunication Code (TC)
Installation Code (IC)
A
–
iv
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Training
ADTRAN offers training courses on our products. These courses include overviews on product
features and functions while covering applications of ADTRAN’s product lines. ADTRAN
provides a variety of training options, including customized training and courses taught at our
facilities or at customer sites.
For inquiries concerning training, contact ADTRAN:
Training Phone:
Training Fax:
800-615-1176, ext. 7500
256-963-6700
Training Email:
61189500L1-1B
PRELIMINARY
v
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
This page is intentionally blank.
vi
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Engineering Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Application Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
MX410 Data Path Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Drop and Continue Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Drop and Insert Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Integrated Wireless Access Device or DS0 Grooming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Receiving Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
ADTRAN Shipping Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Rackmount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Wallmount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Alarm Contacts/AUX Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
61189500L1-1B
PRELIMINARY
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
MX410 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
MX412 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
V.35 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
DS1 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Terminal Server Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
ACO Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Craft Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
FXS Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
PSU Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Turn-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
System Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
Craft Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Logging in to the MX410/MX412. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Menu Layout and Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
Menu Tree. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Menu Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
DS1 Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
DS1 Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Primary Timing Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20
Secondary Timing Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
V.35 Port Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22
Cross-Connect Mapping Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
Terminal Server Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
Terminal Server Port (1 - 4) Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
General Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27
Network Management Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Ethernet Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30
PPP BCP/IPCP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32
DHCP Server Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34
SNMP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-35
SCA Update Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
Quick Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-38
Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-40
Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-42
DS1 (Port #) Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-43
Port (#) Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-44
viii
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
DS1 Test Pattern Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-45
Performance Monitoring Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-46
Daily Performance Monitoring Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-48
Quarter Hour Performance Monitoring Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-48
Daily PM Thresholds Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-49
Quarter Hour PM Thresholds Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-51
Clear PM Data Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-52
System Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-53
Master Log Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-54
Code Download Method Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-55
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Warranty and Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
ADTRAN Sales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
ADTRAN Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
ADTRAN Repair/CAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Repair and Return Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
61189500L1-1B
PRELIMINARY
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Figures
Figure 1-1. MX410 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Figure 1-2. MX412 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Figure 3-1. MX410 Data Path Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Figure 3-2. Drop and Continue Application Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Figure 3-3. Quick Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Figure 3-4. Drop and Continue Quick Setup Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Figure 3-5. Drop and Continue Cross-Connect Mapping Example 1 . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Figure 3-6. Drop and Continue Cross-Connect Mapping Example 2 . . . . . . . . . . . . . . . . . . . . . . . . .3-6
Figure 3-7. Drop and Insert Application Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
Figure 3-8. Quick Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8
Figure 3-9. Drop and Insert Quick Setup Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Figure 3-10. Drop and Insert Cross-Connect Mapping Example 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Figure 3-11. Drop and Insert Cross-Connect Mapping Example 2 . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Figure 3-12. Drop and Insert Cross-Connect Mapping Example 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Figure 3-13. Drop and Insert Cross-Connect Mapping Example 4 . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Figure 3-14. Integrated Wireless Access Device Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
Figure 3-15. Bandwidth Efficiency with DS0 Grooming Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13
Figure 3-16. Quick Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
Figure 3-17. Integrated Wireless Access Device Quick Setup Example . . . . . . . . . . . . . . . . . . . . . .3-15
Figure 3-18. Integrated Wireless Access Device Cross-Connect Map Example 1 . . . . . . . . . . . . . . .3-15
Figure 3-19. Integrated Wireless Access Device Cross-Connect Map Example 2 . . . . . . . . . . . . . . .3-16
Figure 3-20. Integrated Wireless Access Device Cross-Connect Map Example 3 . . . . . . . . . . . . . . .3-16
Figure 3-21. Integrated Wireless Access Device Cross-Connect Map Example 4 . . . . . . . . . . . . . . .3-17
Figure 3-22. Integrated Wireless Access Device Cross-Connect Map Example 5 . . . . . . . . . . . . . . .3-17
Figure 3-23. MX410 Remote Management of Other Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18
Figure 4-1. Rackmount and Wallmount Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Figure 4-2. MX410/MX412 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Figure 4-3. DC Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Figure 4-4. Alarm Contacts and AUX Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Figure 4-5. MX410 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Figure 4-6. MX412 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Figure 5-1. MX410/MX412 Menu Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
Figure 5-2. MX410/MX412 Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Figure 5-3. MX410/MX412 Menu Tree (Continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10
Figure 5-4. MX410/MX412 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
Figure 5-5. Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
Figure 5-6. Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-14
Figure 5-7. DS1 Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-16
Figure 5-8. DS1 Ports Menu - Toggled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-16
Figure 5-9. DS1 Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-18
Figure 5-10. Primary Timing Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-21
Figure 5-11. Secondary Timing Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-22
Figure 5-12. V.35 Port Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-23
Figure 5-13. Cross-Connect Mapping Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-24
Figure 5-14. Cross-Connect Mapping - Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-24
Figure 5-15. Terminal Server Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-27
Figure 5-16. Terminal Server Port 1 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-28
Figure 5-17. General Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-29
x
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Figure 5-18. Network Management Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-31
Figure 5-19. Ethernet Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-32
Figure 5-20. PPP BCP/IPCP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-34
Figure 5-21. DHCP Server Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-35
Figure 5-22. SNMP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-36
Figure 5-23. SCA Update Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-37
Figure 5-24. Quick Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-38
Figure 5-25. Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-40
Figure 5-26. Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-42
Figure 5-27. DS1 (Port #) Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-43
Figure 5-28. Port (#) Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-44
Figure 5-29. DS1 Test Pattern Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-45
Figure 5-30. Performance Monitoring Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-46
Figure 5-31. Daily Performance Monitoring Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-48
Figure 5-32. Quarter Hour Performance Monitoring Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-48
Figure 5-33. Daily PM Thresholds Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-49
Figure 5-34. Quarter Hour PM Thresholds Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-50
Figure 5-35. System Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-51
Figure 5-36. Master Log Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-52
Figure 5-37. Code Download Method Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-53
Tables
MX410 Power Supply Unit Compliance Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Table 2-1. Current Draw at –48 VDC and ±24 VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Table 2-2. Fuse Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Table 2-3. Heat Dissipation at –48 VDC and ±24 VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Table 3-1. Drop and Continue Application - Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Table 3-2. Drop and Insert Application - Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
Table 3-3. Integrated Wireless Access Device Application - Required Equipment . . . . . . . . . . . . .3-13
Table 3-4. Remote Management Application - Required Equipment . . . . . . . . . . . . . . . . . . . . . . .3-18
Table 4-1. AUX Inputs 1-9 Pin List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Table 4-2. V.35 Port Pin List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Table 4-3. RJ-48 Connector Pin List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Table 4-4. Ethernet Port Pin List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
Table 4-5. Terminal Server Port Pin List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
Table 4-6. FXS Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9
Table 4-7. LED Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
Table 5-1. MX410/MX412 Keyboard Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Table 5-2. MX410/MX412 Main Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
Table 5-3. MX410/MX412 Configuration Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-13
Table 5-4. Provisioning Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-15
Table 5-5. DS1 Ports Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-17
Table 5-6. DS1 Provisioning Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-19
Table 5-7. Primary Timing Mode Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-21
Table 5-8. Secondary Timing Mode Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-22
Table 5-9. V.35 Port Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-23
61189500L1-1B
PRELIMINARY
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Table 5-10. Cross-Connect Mapping Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-25
Table 5-11. Performance Monitoring Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-46
xii
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
Introduction
PRODUCT OVERVIEW
The MX410/MX412 delivers full DS0 control to service locations, allowing carriers full utili-
zation of DS1 bandwidth. The MX410 interfaces to four long-haul outside plant protected
DS1s via RJ-48 connectors, while the MX412 interfaces to 12 DS1s. Data and management on
the DS1s can be cross connected on a non-blocking per-DS0 basis to any DS1, V.35 port, and
four PPP ports. Data Ethernet connectivity is provided via four PPP connections used for
Ethernet network extension throughout the network and Telnet-based terminal server ports.
The MX410 houses up to two hot-swappable Power Supply Units (PSU) that provide power
redundancy when two units are deployed. At least one MX410 PSU (P/N 1189501L1) must be
inserted into the MX410 for the MX410 to function. The MX412 has an internal PSU.
Digital Radios Data
Analog Radios Data
Grooming of DS0S
LAN Extension over PPP for Remote Management
Star Configuration of Backhaul
Backhaul
Battery Backup
HVAC
Backhaul Radio Management
4 x DS1
(I/O)
4 x RS-232
V.35
Redundant Power
Capability
DB-9 Craft Interface
E911, etc.
4 x 10/100 Ethernet
Figure 1-1. MX410 Overview
61189500L1-1B
PRELIMINARY
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
MX410/MX412 System Manual
The major features of the MX410/MX412 are as follows:
• 19-inch wall mounting or rack mounting, one rack unit high
• Front panel data connections
• One V.35 port
• Four RJ-45 long-haul DS1 connections (12 on the MX412) with outside plant protection
• A four-port Ethernet switch
• Non-Blocking DS0 cross connect between all DS1 interfaces and the V.35 port
• RJ-45 10Base-T Ethernet connection
• Terminal server functionality
• FXS port (MX412 only)
• DB-9 craft interface for access to Provisioning, Status, Test, and Alarm menus
• Management via Telnet over Ethernet connection or VT100 through a local RS-232, DB-9,
craft port
• End-to-end Ethernet extension over multiple T1s
• Robbed Bit Signaling (RBS) supported on a per DS0 basis
• Hot-swappable PSUs with 1:1 redundancy (MX410 only)
• Independent power feeds with separate returns
• Accepts redundant ±60 to ±22 VDC inputs
• Wire-wrap pins for alarms
• Manual and remote initiated loopback modes
• Meets NEBS Level 3
• Comprehensive test features
1-2
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Product Overview
Digital Radios Data
Analog Radios Data
Grooming of DS0S
LAN Extension over PPP for Remote Management
Star Configuration of Backhaul
Backhaul
Battery Backup
HVAC
Backhaul Radio Management
12 x T1
(I/O)
4 x RS-232
V.35
DB-9 Craft Interface
FXS
E911, etc.
4 x 10/100 Ethernet
Figure 1-2. MX412 Overview
61189500L1-1B
PRELIMINARY
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
MX410/MX412 System Manual
This page is intentionally blank.
1-4
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Engineering Guidelines
GENERAL
This section provides engineering guidelines for network designers who are incorporating an
MX410 or MX412 system into their network.
POWER REQUIREMENTS
Table 2-1 provides the current draw at –48 VDC (operating range of –42 VDC to –60 VDC) and
±24 VDC (operating range of ±22 VDC to ±27 VDC) with redundant PSUs installed.
Table 2-1. Current Draw at –48 VDC and ±24 VDC
Part Number
Equipment
Maximum Current Draw
at –48 VDC
Maximum Current Draw
at ±24 VDC
1189500L1
1189512L1
MX410
MX412
0.23 amps
0.36 amps
0.41 amps
0.76 amps
Table 2-2 provides data for determining the recommended fuse for the fuse and alarm panel
that services the MX410/MX412.
Table 2-2. Fuse Recommendations
System Voltage
–48 VDC
Recommended Fuse
2 amps, slow-blow
2 amps, slow-blow
±24 VDC
61189500L1-1B
PRELIMINARY
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Dissipation
MX410/MX412 System Manual
POWER DISSIPATION
Table 2-3 provides the heat dissipation data at –48 VDC (operating range of –42 VDC to
–60 VDC) and ±24 VDC (operating range of ±22 VDC to ±27 VDC) with redundant PSUs
installed (MX410 only).
Table 2-3. Heat Dissipation at –48 VDC and ±24 VDC
Part Number
Equipment
Heat Dissipation
at –48 VDC
Heat Dissipation
at ±24 VDC
1189500L1
1189512L1
MX410
MX412
11.8 watts
17.3 watts
10.5 watts
18.2 watts
2-2
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
Application Guidelines
INTRODUCTION
This section describes several applications for the MX410/MX412 system. For each appli-
cation there is a figure illustrating the application, a list of the equipment needed, and an
explanation of the basic setup. The MX410 block diagram shows the data path of an MX410
system that implements the following applications:
61189500L1-1B
PRELIMINARY
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
MX410 DATA PATH BLOCK DIAGRAM
be mapped between four DS1s (12 DS1s on the MX412), four PPP ports, and a V.35 port. Refer
Any DS0 in DS1 1 can be mapped to any DS0 in DS1 1-4, or any PPP port, or the V.35 port.
Any unmapped DS0 in a DS1 is filled with all ones. Therefore, if an entire T1 is unmapped,
framed all ones are sent.
The default mapping of the 1/0 cross connect is for all the DS1s to be unmapped and trans-
mitting framed all ones. No DS0s are dropped to the PPP or V.35 ports.
MX410
DS1 1 DS0 # 1
DS1 1 DS0 # 2
PPP 1 DS0 # 1
PPP 1 DS0 # 2
DS1
DS1 1
DS1 2
DS1 3
DS1 4
PPP 1
Framer
DS1 1 DS0 # 24
PPP 1 DS0 # 24
DS1 2 DS0 # 1
DS1 2 DS0 # 2
PPP 2 DS0 # 1
PPP 2 DS0 # 2
1/0 Cross Connect
DS1
Framer
PPP 2
PPP 3
PPP 4
DS1 2 DS0 # 24
PPP 2 DS0 # 24
DS1 3 DS0 # 1
DS1 3 DS0 # 2
PPP 3 DS0 # 1
PPP 3 DS0 # 2
DS1
Framer
DS1 3 DS0 # 24
PPP 3 DS0 # 24
DS1 4 DS0 # 1
DS1 4 DS0 # 2
PPP 4 DS0 # 1
PPP 4 DS0 # 2
DS1
Framer
DS1 4 DS0 # 24
PPP 4 DS0 # 24
MX410 IP
V.35 Port
TS 1 TS 2 TS 3 TS 4
ETH 1 ETH 2 ETH 3 ETH 4
Figure 3-1. MX410 Data Path Block Diagram
3-2
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Drop and Continue Application
Drop and Continue Application
cation, any combination of DS0s from one DS1 can be dropped out the other DS1 ports with
the remaining DS0s continuing through to the other DS1 interface. This enables the
bandwidth of one DS1 to deliver DS0s to several sites using one MX410 at each site.
Remote
Site #1
Remote
Site #2
Central
Site
Original DS0s
Continue
Original DS0s
Continue
24 DS0s
from Central Site
Downstream;
All Ones in
Downstream;
All Ones in
Unmapped DS0s
Unmapped DS0s
MX410
MX410
DS1
DS1
DS1
µ Wave/
µ Wave/
µ Wave/
DS1
DS1
DS1
DS1
DS1
Leased
DS1
Leased
DS1
Leased
DS1
Switch
Switch
Drop DS0s
Drop DS0s
Drop DS0s
to Local
Drop DS0s
to Local
to PPP to
Control
to PPP to
Control
Equipment
Equipment
Local
Local
Equipment
via Ethernet
Equipment
via Ethernet
Figure 3-2. Drop and Continue Application Diagram
Table 3-1. Drop and Continue Application - Required Equipment
Part Number
Equipment
Quantity
1189500L1
or
MX410
1
1189512L1
MX412
1
1189501L1
MX410 PSU (MX410 only)
1 (2 for redundancy)
61189500L1-1B
PRELIMINARY
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Drop and Continue Application
MX410/MX412 System Manual
Setup
Connect the incoming DS1 (the DS1 from which the DS0s are dropped) to the DS1 1 RJ.
Connect the outgoing DS1 to the DS1 2 RJ. Connect the other DS1s using the RJ connector
Starting from the default blank mapping, the DS0s can be dropped using the Quick Setup
DS0 needs to be dropped from the incoming DS1. For each port, select the range of DS0s in
DS1 1 to be dropped to that port. To drop DS0s to the other DS1 ports, use the Quick Setup
menu to navigate to the Cross-Connect Mapping menu. Select the Map Multiple DS0’s option
and then select the range of DS0 and DS1 1 to be dropped to DS1 2 and enable Robbed Bit
Signaling if applicable.
Any un-mapped DS0s from the incoming DS1 will transmit All Ones. The incoming DS1 does
not have to be DS1 1, but is used only as an example.
The following four figures show an example of setting up a drop and continue application.
Figure 3-3 shows the Quick Setup menu before any DS0s have been dropped.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Quick Setup
Ports
1 - PPPs
PPP 1 = DS1 4 DS0 #1
2 - V.35 =
System
3 - System ID
4 - IP Address
Subnet Mask
5 - Default Gateway
6 - Date
: 192.168.100.1
: 255.255.0.0
: 192.168.1.1
7 - Time
8 - Cross-Connect Mapping
Selection :
'?' - System Help Screen
Figure 3-3. Quick Setup Menu
3-4
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Drop and Continue Application
Figure 3-4 shows the Quick Setup menu after DS0s 21-22 have been dropped from DS1 1 to
PPP1, DS0s 23-24 have been dropped from DS1 1 to the V.35 port.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Quick Setup
Ports
1 - PPPs
PPP 1 = DS1 4 DS0 #1
2 - V.35 =
System
3 - System ID
4 - IP Address
Subnet Mask
5 - Default Gateway
6 - Date
: 192.168.100.1
: 255.255.0.0
: 192.168.1.1
7 - Time
8 - Cross-Connect Mapping
Selection :
'?' - System Help Screen
Figure 3-4. Drop and Continue Quick Setup Example
Figure 3-5 shows the DS1 1 Cross-Connect Mapping menu after the PPP1 and V.35 interface
have been mapped.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 1
1 - DS0 #1 =
2 - DS0 #2 =
3 - DS0 #3 =
4 - DS0 #4 =
5 - DS0 #5 =
6 - DS0 #6 =
7 - DS0 #7 =
8 - DS0 #8 =
9 - DS0 #9 =
10 - DS0 #10 =
11 - DS0 #11 =
12 - DS0 #12 =
13 - DS0 #13 =
14 - DS0 #14 =
15 - DS0 #15 =
16 - DS0 #16 =
17 - DS0 #17 =
18 - DS0 #18 =
19 - DS0 #19 =
20 - DS0 #20 =
21 - DS0 #21 = PPP 1
22 - DS0 #22 = PPP 1
23 - DS0 #23 = V.35
24 - DS0 #24 = V.35
(T)oggle View (DS1 2, DS1 3, DS1 4, Ports)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-5. Drop and Continue Cross-Connect Mapping Example 1
61189500L1-1B
PRELIMINARY
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Drop and Continue Application
MX410/MX412 System Manual
Figure 3-6 shows the Cross-Connect Mapping menu after the remaining DS0s have been
continued to DS1 2 as well as 4 DS0s (13-16) dropped to DS1 3 (1-4) and four other DS0s
(17-20) dropped to DS1 4 (1-4).
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 1
1 - DS0 #1 = DS1 2 DS0 #1
2 - DS0 #2 = DS1 2 DS0 #2
3 - DS0 #3 = DS1 2 DS0 #3
4 - DS0 #4 = DS1 2 DS0 #4
5 - DS0 #5 = DS1 2 DS0 #5
6 - DS0 #6 = DS1 2 DS0 #6
7 - DS0 #7 = DS1 2 DS0 #7
8 - DS0 #8 = DS1 2 DS0 #8
9 - DS0 #9 = DS1 2 DS0 #9
10 - DS0 #10 = DS1 2 DS0 #10
11 - DS0 #11 = DS1 2 DS0 #11
12 - DS0 #12 = DS1 2 DS0 #12
13 - DS0 #13 = DS1 3 DS0 #1
14 - DS0 #14 = DS1 3 DS0 #2
15 - DS0 #15 = DS1 3 DS0 #3
16 - DS0 #16 = DS1 3 DS0 #4
17 - DS0 #17 = DS1 4 DS0 #1
18 - DS0 #18 = DS1 4 DS0 #2
19 - DS0 #19 = DS1 4 DS0 #3
20 - DS0 #20 = DS1 4 DS0 #4
21 - DS0 #21 = PPP 1
22 - DS0 #22 = PPP 1
23 - DS0 #23 = V.35
24 - DS0 #24 = V.35
(T)oggle View (DS1 2, DS1 3, DS1 4, Ports)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-6. Drop and Continue Cross-Connect Mapping Example 2
3-6
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Drop and Insert Application
Drop and Insert Application
cation DS0s from one DS1 can be dropped out to the other DS1 ports. Then, DS0s from the
other DS1 ports can be inserted into the corresponding DS0s in the other DS1. In the example
shown, any DS0 not dropped will be mapped to continue on from one DS1 to another. This
allows a DS1 to be used to transport DS0s between several sites.
Central
Site
Remote
Site #1
Remote
Site #2
Original DS0s
Continue
Original DS0s
Continue
24 DS0s
Downstream;
All Ones in
from Central Site
Downstream;
All Ones in
Unmapped DS0s
Unmapped DS0s
MX410
MX410
DS1
DS1
DS1
µ Wave/
Leased
DS1
µ Wave/
µ Wave/
DS1
DS1
DS1
DS1
DS1
Leased
DS1
Leased
DS1
Switch
Switch
DS0s
DS0s
Drop DS0s
Drop DS0s
to PPP to
Control
to/from Local
Equipment
to/from Local
Equipment
to PPP to
Control
Local
Local
Equipment
via Ethernet
Equipment
via Ethernet
Insert DS0s
Insert DS0s
from
from
PPP to Continue
Ethernet Path
Conserving
Bandwidth
PPP to Continue
Ethernet Path
Conserving
Bandwidth
Figure 3-7. Drop and Insert Application Diagram
Table 3-2. Drop and Insert Application - Required Equipment
Part #
Equipment
Quantity
1189500L1
or
MX410
1
1189512L1
MX412
1
1189501L1
MX410 PSU (MX410 only)
1 (2 for redundancy)
61189500L1-1B
PRELIMINARY
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Drop and Insert Application
MX410/MX412 System Manual
Setup
Connect the DS1 from which the DS0s will be dropped to the DS1 1 RJ. Connect the other
DS1 to which the DS0s will be inserted to the DS1 2 RJ. Connect the other DS1s using the
Starting from the default mapping the DS0s can be dropped and inserted using the Quick
dropped from the incoming DS1. For each port select the DS0(s) in DS1 1 to be dropped to
that port. Then, select each port and DS0 that needs to be inserted into the other DS1. For
each DS0 to be inserted select the DS0 in DS1 2 to insert that DS0. Using the Cross-Connect
Mapping menu, select each DS0 that is to be dropped to other DS1 ports as well. Select the
Map Multiple DS0’s option and then select the range of DS0 and DS1 1 to be dropped to DS1
2 and enable Robbed Bit Signaling if applicable.
For each DS0 dropped out of the incoming DS1 (DS1 1 in this example), that does not have a
DS0 dropped or inserted into the corresponding DS0 in the other DS1 (DS1 2 in this example),
map the remaining DS0s to continue the data downstream. Any unmapped DS0 will transmit
all ones.
The following six figures show an example of setting up a drop and insert application. Figure
3-8 shows the Quick Setup menu before any DS0s have been dropped.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Quick Setup
Ports
1 - PPPs
PPP 1 = DS1 4 DS0 #1
2 - V.35 =
System
3 - System ID
4 - IP Address
Subnet Mask
5 - Default Gateway
6 - Date
: 192.168.100.1
: 255.255.0.0
: 192.168.1.1
7 - Time
8 - Cross-Connect Mapping
Selection :
'?' - System Help Screen
Figure 3-8. Quick Setup Menu
3-8
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Drop and Insert Application
Figure 3-9 shows the Quick Setup menu after DS0s 23-24 have been dropped from DS1 1 to
PPP1 and PPP 2 has been inserted into DS0s 23-24 in DS1 2.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Quick Setup
Ports
1 - PPPs
PPP 1 = DS1 1 DS0 #23-24
PPP 2 = DS1 2 DS0 #23-24
2 - V.35 = DS1 1 DS0 #23-24
System
3 - System ID
4 - IP Address
Subnet Mask
5 - Default Gateway
6 - Date
: 192.168.100.1
: 255.255.0.0
: 192.168.1.1
7 - Time
8 - Cross-Connect Mapping
Selection :
'?' - System Help Screen
Figure 3-9. Drop and Insert Quick Setup Example
Figure 3-10 shows the Cross-Connect Mapping menu for DS1 1 after mapping the PPPs but
prior to mapping the remaining DS0s to be dropped and continued.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 1
1 - DS0 #1 =
2 - DS0 #2 =
3 - DS0 #3 =
4 - DS0 #4 =
5 - DS0 #5 =
6 - DS0 #6 =
7 - DS0 #7 =
8 - DS0 #8 =
9 - DS0 #9 =
10 - DS0 #10 =
11 - DS0 #11 =
12 - DS0 #12 =
13 - DS0 #13 =
14 - DS0 #14 =
15 - DS0 #15 =
16 - DS0 #16 =
17 - DS0 #17 =
18 - DS0 #18 =
19 - DS0 #19 =
20 - DS0 #20 =
21 - DS0 #21 =
22 - DS0 #22 =
23 - DS0 #23 = PPP 1
24 - DS0 #24 = PPP 1
(T)oggle View (DS1 2, DS1 3, DS1 4, Ports)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-10. Drop and Insert Cross-Connect Mapping Example 1
61189500L1-1B
PRELIMINARY
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Drop and Insert Application
MX410/MX412 System Manual
Figure 3-11 shows the Cross-Connect Mapping menu after DS0s 1-12 are continued through
from DS1 1 to DS1 2 and DS0s 13-23 are dropped from DS1 1 to DS1 3.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 1
1 - DS0 #1 = DS1 2 DS0 #1
2 - DS0 #2 = DS1 2 DS0 #2
3 - DS0 #3 = DS1 2 DS0 #3
4 - DS0 #4 = DS1 2 DS0 #4
5 - DS0 #5 = DS1 2 DS0 #5
6 - DS0 #6 = DS1 2 DS0 #6
7 - DS0 #7 = DS1 2 DS0 #7
8 - DS0 #8 = DS1 2 DS0 #8
9 - DS0 #9 = DS1 2 DS0 #9
10 - DS0 #10 = DS1 2 DS0 #10
11 - DS0 #11 = DS1 2 DS0 #11
12 - DS0 #12 = DS1 2 DS0 #12
13 - DS0 #13 = DS1 3 DS0 #1
14 - DS0 #14 = DS1 3 DS0 #2
15 - DS0 #15 = DS1 3 DS0 #3
16 - DS0 #16 = DS1 3 DS0 #4
17 - DS0 #17 = DS1 3 DS0 #5
18 - DS0 #18 = DS1 3 DS0 #6
19 - DS0 #19 = DS1 3 DS0 #7
20 - DS0 #20 = DS1 3 DS0 #8
21 - DS0 #21 = DS1 3 DS0 #9
22 - DS0 #22 = DS1 3 DS0 #10
23 - DS0 #23 = PPP 1
24 - DS0 #24 = PPP 1
(T)oggle View (DS1 2, DS1 3, DS1 4, Ports)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-11. Drop and Insert Cross-Connect Mapping Example 2
Figure 3-12 shows the Cross-Connect Mapping menu for DS1 2 after all ports are dropped
and continued from DS1 1.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 2
1 - DS0 #1 = DS1 1 DS0 #1
2 - DS0 #2 = DS1 1 DS0 #2
3 - DS0 #3 = DS1 1 DS0 #3
4 - DS0 #4 = DS1 1 DS0 #4
5 - DS0 #5 = DS1 1 DS0 #5
6 - DS0 #6 = DS1 1 DS0 #6
7 - DS0 #7 = DS1 1 DS0 #7
8 - DS0 #8 = DS1 1 DS0 #8
9 - DS0 #9 = DS1 1 DS0 #9
10 - DS0 #10 = DS1 1 DS0 #10
11 - DS0 #11 = DS1 1 DS0 #11
12 - DS0 #12 = DS1 1 DS0 #12
13 - DS0 #13 =
14 - DS0 #14 =
15 - DS0 #15 =
16 - DS0 #16 =
17 - DS0 #17 =
18 - DS0 #18 =
19 - DS0 #19 =
20 - DS0 #20 =
21 - DS0 #21 =
22 - DS0 #22 =
23 - DS0 #23 = PPP 2
24 - DS0 #24 = PPP 2
(T)oggle View (DS1 3, DS1 4, Ports, DS1 1)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-12. Drop and Insert Cross-Connect Mapping Example 3
3-10 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Drop and Insert Application
Figure 3-13 the Cross-Connect Mapping menu after DS0s 13-23 are inserted in DS1 2 from
DS1 4. Any unmapped DS0s will be filled with all ones.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 2
1 - DS0 #1 = DS1 1 DS0 #1
2 - DS0 #2 = DS1 1 DS0 #2
3 - DS0 #3 = DS1 1 DS0 #3
4 - DS0 #4 = DS1 1 DS0 #4
5 - DS0 #5 = DS1 1 DS0 #5
6 - DS0 #6 = DS1 1 DS0 #6
7 - DS0 #7 = DS1 1 DS0 #7
8 - DS0 #8 = DS1 1 DS0 #8
9 - DS0 #9 = DS1 1 DS0 #9
10 - DS0 #10 = DS1 1 DS0 #10
11 - DS0 #11 = DS1 1 DS0 #11
12 - DS0 #12 = DS1 1 DS0 #12
13 - DS0 #13 = DS1 4 DS0 #1
14 - DS0 #14 = DS1 4 DS0 #2
15 - DS0 #15 = DS1 4 DS0 #3
16 - DS0 #16 = DS1 4 DS0 #4
17 - DS0 #17 = DS1 4 DS0 #5
18 - DS0 #18 = DS1 4 DS0 #6
19 - DS0 #19 = DS1 4 DS0 #7
20 - DS0 #20 = DS1 4 DS0 #8
21 - DS0 #21 = DS1 4 DS0 #9
22 - DS0 #22 = DS1 4 DS0 #10
23 - DS0 #23 = PPP 2
24 - DS0 #24 = PPP 2
(T)oggle View (DS1 3, DS1 4, Ports, DS1 1)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-13. Drop and Insert Cross-Connect Mapping Example 4
61189500L1-1B
PRELIMINARY 3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Integrated Wireless Access Device or DS0 Grooming
MX410/MX412 System Manual
Integrated Wireless Access Device or DS0 Grooming
Integrated Wireless Access Device Application, bandwidth is conserved by using the MX410 to
groom multiple fractional T1s into a single T1. This allows the MX410 to be used as an
through the cross connect.
Central
Site
DS1
µ Wave/
Leased
DS1
24 DS0s
from Central Site
DS1 #1
MX410
DS1 #4
E911
Other systems
currently managed by
the MX410 through
an Ethernet port
to Ethernet port
Remote Site #1
V.35
TSR1
Battery
ETH1
ETH2
Charger
Switch
connection
DS1 #3
DS1 #2
Digital
Digital
Analog
Base Station
Transceiver
Base Station
Transceiver
Base Station
Transceiver
Figure 3-14. Integrated Wireless Access Device Diagram
3-12 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Integrated Wireless Access Device or DS0 Grooming
Central
Site
DS1
µ Wave/
Leased
DS1
24 DS0s
from Central Site
Original DS0s
Original DS0s
Continue
Original DS0s
Original DS0s
Continue
MX410
MX410
MX410
Continue
Continue
Downstream;
All Ones in
Remote Site #4
Remote Site #1
Remote Site #2
Downstream;
All Ones in
Downstream;
All Ones in
Downstream;
All Ones in
Unmapped DS0s
Unmapped DS0s
Unmapped DS0s
Unmapped DS0s
DS1
DS1
DS1
DS1
µ Wave/
µ Wave/
µ Wave/
Leased
DS1
µ Wave/
DS1
DS1
DS1
DS1
DS1
DS1
Switch
Switch
Leased
DS1
Leased
DS1
Switch
Leased
DS1
Drop DS0s
Drop DS0s
Drop DS0s
Drop DS0s
to PPP to
Control
Drop DS0s
to PPP to
Control
Original DS0s
Continue
to/from Local
Equipment
to/from Local
Equipment
to PPP to
Control
DS1
µ Wave/
Leased
DS1
Downstream;
All Ones in
Local
Local
Local
Equipment
via Ethernet
Equipment
via Ethernet.
Equipment
via Ethernet.
Unmapped DS0s
Insert DS0s from
PPP to Continue
Ethernet Path
Conserving
Insert DS0s from
PPP to Continue
Ethernet Path
Conserving
MX410
Bandwidth
Bandwidth
Remote Site #3
DS1
µ Wave/
Leased
DS1
DS1
Original DS0s
Continue
Switch
Downstream;
All Ones in
Unmapped DS0s
Drop DS0s
Drop DS0s
to/from Local
Equipment
to PPP to
Control
Local
Equipment
via Ethernet.
Insert DS0s from
PPP to Continue
Ethernet Path
Conserving
Bandwidth
Figure 3-15. Bandwidth Efficiency with DS0 Grooming Diagram
The equipment needed for an Integrated Wireless Access Device or Bandwidth Efficiency with
Table 3-3. Integrated Wireless Access Device Application - Required Equipment
Part Number
Equipment
Quantity
1189500L1
or
MX410
1
1189512L1
MX412
1
1189501L1
MX410 PSU (MX410 only)
1 (2 for redundancy)
61189500L1-1B
PRELIMINARY 3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Integrated Wireless Access Device or DS0 Grooming
MX410/MX412 System Manual
Setup
Connect the DS1 from which the DS0s will be dropped to the DS1 1 RJ. Connect the other
Starting from the default mapping the DS0s can be mapped using the Quick Setup menu
incoming DS1. For each port select the DS0(s) in DS1 1 to be dropped to that port. Using the
Cross-Connect Mapping menu, select each DS0 that are to be mapped from other DS1 ports
as well. Select the Map Multiple DS0’s option and then select the range of DS0 and DS1 1 to
be dropped to DS1 2 and enable Robbed Bit Signaling if applicable.
For an integrated wireless access device application, map DS0s to the corresponding DS0 in
the other DS1 (DS1 2, 3, and 4 in this example). For a grooming application, each DS0
dropped out of the incoming DS1 (DS1 1 in this example), that does not have a DS0 dropped
or inserted into the corresponding DS0 in the other DS1 (DS1 2,3 and 4 in this example), map
the groomed DS0s to continue the data downstream. Any unmapped DS0 will transmit all
ones.
The following six figures show an example of setting up an integrated wireless access device or
dropped.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Quick Setup
Ports
1 - PPPs
2 - V.35 =
System
3 - System ID
4 - IP Address
Subnet Mask
5 - Default Gateway
6 - Date
: 192.168.100.1
: 255.255.0.0
: 192.168.1.1
7 - Time
8 - Cross-Connect Mapping
Selection :
'?' - System Help Screen
Figure 3-16. Quick Setup Menu
3-14 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Integrated Wireless Access Device or DS0 Grooming
Figure 3-17 shows the Quick Setup menu after DS0s 23-24 have been dropped from DS1 1 to
PPP1, and PPP 2, 3, and 4 have been inserted into DS0s 23-24 in DS1 2, 3 and 4 respectively.
PPP 2, 3, and 4 are typically not used in this fashion for the integrated wireless access device
application.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Quick Setup
Ports
1 - PPPs
PPP 1 = DS1 1 DS0 #23-24
PPP 2 = DS1 2 DS0 #23-24
PPP 3 = DS1 3 DS0 #23-24
PPP 4 = DS1 4 DS0 #23-24
2 - V.35 =
System
3 - System ID
4 - IP Address
Subnet Mask
5 - Default Gateway
6 - Date
: 192.168.100.1
: 255.255.0.0
: 192.168.1.1
7 - Time
8 - Cross-Connect Mapping
Selection :
'?' - System Help Screen
Figure 3-17. Integrated Wireless Access Device Quick Setup Example
Figure 3-18 shows the Cross-Connect Mapping menu for DS1 1 after mapping the PPPs but
prior to mapping the remaining DS0s to be mapped.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 1
1 - DS0 #1 =
2 - DS0 #2 =
3 - DS0 #3 =
4 - DS0 #4 =
5 - DS0 #5 =
6 - DS0 #6 =
7 - DS0 #7 =
8 - DS0 #8 =
9 - DS0 #9 =
10 - DS0 #10 =
11 - DS0 #11 =
12 - DS0 #12 =
13 - DS0 #13 =
14 - DS0 #14 =
15 - DS0 #15 =
16 - DS0 #16 =
17 - DS0 #17 =
18 - DS0 #18 =
19 - DS0 #19 =
20 - DS0 #20 =
21 - DS0 #21 =
22 - DS0 #22 =
23 - DS0 #23 = PPP 1
24 - DS0 #24 = PPP 1
(T)oggle View (DS1 2, DS1 3, DS1 4, Ports)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-18. Integrated Wireless Access Device Cross-Connect Map Example 1
61189500L1-1B
PRELIMINARY 3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Integrated Wireless Access Device or DS0 Grooming
MX410/MX412 System Manual
Figure 3-19 shows the Cross-Connect Mapping menu after DS0s 1-7 are mapped from DS1 1
to DS1 2, DS0s 8-15 are mapped from DS1 1 to DS1 3, and DS0s 15-22 are mapped from DS1
1 to DS1 4.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 1
1 - DS0 #1 = DS1 2 DS0 #1
2 - DS0 #2 = DS1 2 DS0 #2
3 - DS0 #3 = DS1 2 DS0 #3
4 - DS0 #4 = DS1 2 DS0 #4
5 - DS0 #5 = DS1 2 DS0 #5
6 - DS0 #6 = DS1 2 DS0 #6
7 - DS0 #7 = DS1 2 DS0 #7
8 - DS0 #8 = DS1 3 DS0 #1
9 - DS0 #9 = DS1 3 DS0 #2
10 - DS0 #10 = DS1 3 DS0 #3
11 - DS0 #11 = DS1 3 DS0 #4
12 - DS0 #12 = DS1 3 DS0 #5
13 - DS0 #13 = DS1 3 DS0 #6
14 - DS0 #14 = DS1 3 DS0 #7
15 - DS0 #15 = DS1 4 DS0 #1
16 - DS0 #16 = DS1 4 DS0 #2
17 - DS0 #17 = DS1 4 DS0 #3
18 - DS0 #18 = DS1 4 DS0 #4
19 - DS0 #19 = DS1 4 DS0 #5
20 - DS0 #20 = DS1 4 DS0 #6
21 - DS0 #21 = DS1 4 DS0 #7
22 -
23 - DS0 #23 = PPP 1
24 - DS0 #24 = PPP 1
(T)oggle View (DS1 2, DS1 3, DS1 4, Ports)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-19. Integrated Wireless Access Device Cross-Connect Map Example 2
Figure 3-20 shows the Cross-Connect Mapping menu for DS1 2 after all ports are mapped
from DS1 1.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 2
1 - DS0 #1 = DS1 1 DS0 #1
2 - DS0 #2 = DS1 1 DS0 #2
3 - DS0 #3 = DS1 1 DS0 #3
4 - DS0 #4 = DS1 1 DS0 #4
5 - DS0 #5 = DS1 1 DS0 #5
6 - DS0 #6 = DS1 1 DS0 #6
7 - DS0 #7 = DS1 1 DS0 #7
8 - DS0 #8 =
13 - DS0 #13 =
14 - DS0 #14 =
15 - DS0 #15 =
16 - DS0 #16 =
17 - DS0 #17 =
18 - DS0 #18 =
19 - DS0 #19 =
20 - DS0 #20 =
21 - DS0 #21 =
22 - DS0 #22 =
9 - DS0 #9 =
10 - DS0 #10 =
11 - DS0 #11 =
12 - DS0 #12 =
23 - DS0 #23 = PPP 2
24 - DS0 #24 = PPP 2
(T)oggle View (DS1 3, DS1 4, Ports, DS1 1)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-20. Integrated Wireless Access Device Cross-Connect Map Example 3
3-16 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Integrated Wireless Access Device or DS0 Grooming
Figure 3-21 shows the Cross-Connect Mapping menu for DS1 3.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 3
1 - DS0 #1 = DS1 1 DS0 #8
2 - DS0 #2 = DS1 1 DS0 #9
3 - DS0 #3 = DS1 1 DS0 #10
4 - DS0 #4 = DS1 1 DS0 #11
5 - DS0 #5 = DS1 1 DS0 #12
6 - DS0 #6 = DS1 1 DS0 #13
7 - DS0 #7 = DS1 1 DS0 #14
8 - DS0 #8 =
13 - DS0 #13 =
14 - DS0 #14 =
15 - DS0 #15 =
16 - DS0 #16 =
17 - DS0 #17 =
18 - DS0 #18 =
19 - DS0 #19 =
20 - DS0 #20 =
21 - DS0 #21 =
22 - DS0 #22 =
9 - DS0 #9 =
10 - DS0 #10 =
11 - DS0 #11 =
12 - DS0 #12 =
23 - DS0 #23 = PPP 3
24 - DS0 #24 = PPP 3
(T)oggle View (DS1 4, Ports, DS1 1, DS1 2)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-21. Integrated Wireless Access Device Cross-Connect Map Example 4
Figure 3-22 shows the Cross-Connect Mapping menu for DS1 4. Any unmapped DS0s are
filled with all ones.
MX410
MINOR
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 4
1 - DS0 #1 = DS1 1 DS0 #15
2 - DS0 #2 = DS1 1 DS0 #16
3 - DS0 #3 = DS1 1 DS0 #17
4 - DS0 #4 = DS1 1 DS0 #18
5 - DS0 #5 = DS1 1 DS0 #19
6 - DS0 #6 = DS1 1 DS0 #20
7 - DS0 #7 = DS1 1 DS0 #21
8 - DS0 #8 =
13 - DS0 #13 =
14 - DS0 #14 =
15 - DS0 #15 =
16 - DS0 #16 =
17 - DS0 #17 =
18 - DS0 #18 =
19 - DS0 #19 =
20 - DS0 #20 =
21 - DS0 #21 =
22 - DS0 #22 =
9 - DS0 #9 =
10 - DS0 #10 =
11 - DS0 #11 =
12 - DS0 #12 =
23 - DS0 #23 = PPP 4
24 - DS0 #24 = PPP 4
(T)oggle View (Ports, DS1 1, DS1 2, DS1 3)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 3-22. Integrated Wireless Access Device Cross-Connect Map Example 5
61189500L1-1B
PRELIMINARY 3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Management of Other Systems using Terminal Server Ports and Ethernet Connectivity MX410/MX412 System Manual
Remote Management of Other Systems using Terminal Server
Ports and Ethernet Connectivity
In this application the Terminal Server ports on the MX410 are used to provide remote
management of other non-Ethernet based equipment at the same site. This requires
connecting the RS-232 craft ports of the other equipment to the Terminal Server ports of the
MX410. Establishing a Telnet session to the MX410 Terminal Server ports establishes access
to the other equipment. Up to four external devices can be accessed in this way.
The Ethernet ports on the MX410 are used to provide remote management of the other
Ethernet based equipment. This requires connecting the Ethernet ports of the other
Original DS0s
Continue
Original DS0s
Continue
Downstream;
All Ones in
Downstream;
All Ones in
Unmapped DS0s
Unmapped DS0s
DS1
DS1
MX410
DS1
DS1
DS1
DS1
µ Wave/
Leased
DS1
µ Wave/
Leased
DS1
MX410
IP
Ethernet
Switch
Terminal Server Ports
Ethernet Ports
Technician
Manages All
Ethernet Ports
MX410 Units
and Other Systems
from Any Cell Site
RS-232 Ports
Other Systems
Other Systems
Currently Managed
by the MX410 via
Ethernet Port to
Ethernet Port
Currently Managed
by the MX410 via
Terminal Server Port
to RS-232 Craft Port
Connections
Connections
Figure 3-23. MX410 Remote Management of Other Systems
Table 3-4. Remote Management Application - Required Equipment
Part Number
Equipment
Quantity
1189500L1
or
MX410
1
1189512L1
MX412
1
1189501L1
MX410 PSU (MX410 only)
1 (2 for redundancy)
3-18 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual Remote Management of Other Systems using Terminal Server Ports and Ethernet Connectivity
Setup
First, connect the RS-232 craft port on the other equipment to the MX410 terminal server
port. The pin assignments for each of the RS-232 interfaces are listed in the PORT 1-4
The default settings for the terminal server ports are 9600 bps 8 data bits with no parity.
These settings must match the craft port settings of the other equipment for the application to
work. Baud Rate can be changed in the MX410 Terminal Server menus under Provisioning.
Then, establish a Telnet session to the MX410 with the port number for the particular port to
access the other equipment. The default IP address for the MX410 is 192.168.100.1 with a
subnet mask of 255.255.0.0. The port numbers default to 2023, 2024, 2025, and 2026
respectively, for each of the four ports. Once the session is established the default username
for each port is “port #” (where # is the number of the port) and the default password is
“password”.
For Ethernet based devices, simply assign a static IP address to the other equipment (or
enable the DHCP server to provide one) and connect its Ethernet port to one of the four switch
page 5-34 for more information about DHCP servers.
61189500L1-1B
PRELIMINARY 3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Management of Other Systems using Terminal Server Ports and Ethernet Connectivity MX410/MX412 System Manual
This page is intentionally blank.
3-20 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Installation
GENERAL
The first three tasks for installing and operating the MX410/MX412 are to unpack, inspect,
and install. Those tasks are detailed in this section of the manual, as well as information for
mounting the MX410/MX412 into an equipment rack or to a wall, making the proper connec-
tions to the front and back panels, identifying the front panel indicators, and adding or
removing a Power Supply Unit (PSU) (MX410 only).
RECEIVING INSPECTION
Inspect the MX410/MX412 for any damage that might have occurred in shipment. If damage
is suspected, file a claim immediately with the carrier, keep the original packaging for damage
verification and/or returning the unit, and contact ADTRAN Customer Service. For warranty
ADTRAN SHIPPING CONTENTS
After unpacking the MX410 or MX412 but before an initial power up, be sure that the
following items are present:
• MX410 and MX410 PSU
or
MX412
• Mounting brackets and screws for 19-inch rack or wall installation
– Ground lug with nut and lock washer
– Wire-wrap post cover and screw
– Power connector
– Blank PSU cover (MX410 only)
61189500L1-1B
PRELIMINARY
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Rackmount
MX410/MX412 System Manual
RACKMOUNT
For a rackmount installation, perform the following steps:
1. Ensure the mounting brackets to the MX410/MX412 are attached using the two screws
provided for each bracket.
• For 19-inch rack applications, attach the brackets with the short flange parallel with the
• For 23-inch rack applications, attach the brackets with the short flange parallel with the
front of the chassis and obtain 23-inch adapter mounting hardware.
2. Connect the frame ground from the frame ground lug on the upper right rear panel of the
MX410/MX412 to the equipment rack grounding screw or other appropriate grounding
connection before mounting.
3. Use the appropriate rack type screws to mount the MX410/MX412 into the rack.
CAUTION
Care should be taken to not upset the stability of the equipment
rack after installation is complete.
NOTE
The unit must be installed in accordance with the requirements of
NEC NFPA 70. When mounting the MX410/MX412 in a rack,
multiple chassis can be mounted in adjacent rack slots.
WALLMOUNT
For a wallmount installation, perform the following steps:
1. Ensure the mounting brackets to the MX410/MX412 are attached using the two screws
provided for each bracket. Attach the brackets with the short flange parallel with the
2. Connect the frame ground from the frame ground lug on the upper right rear panel of the
MX410/MX412 to an appropriate grounding connection.
3. Mount the MX410/MX412 vertically with the front panel facing to the left or right side.
Figure 4-1. Rackmount and Wallmount Orientation
4-2
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Rear Panel
REAR PANEL
The MX410/MX412 rear panel is equipped with wire-wrap pins for external auxiliary inputs,
wire-wrap pins for alarms (critical, major, and minor), a frame ground lug, and a single power
Figure 4-2. MX410/MX412 Rear View
WARNING
The Alarm interfaces and AUX inputs must not be metallically
connected to interfaces which connect to the Outside Plant or its
wiring. These interfaces are designed for use as intra-building
interfaces only. The addition of Primary Protectors is not sufficient
protection in order to connect these interfaces metallically to OSP
wiring.
Power Connection
11 for more power information.
Power Connector
Figure 4-3. DC Power Connections
61189500L1-1B
PRELIMINARY
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
MX410/MX412 System Manual
Alarm Contacts/AUX Inputs
Figure 4-4. Alarm Contacts and AUX Inputs
The alarm interfaces connect to the nine Form C type relays on the MX410/MX412 labeled
CRIT, MAJOR, and MINOR. Both NC (Normally Closed) and NO (Normally Open) contacts are
provided. Connect the CRIT (Critical), MAJOR, and MINOR alarm leads from the fuse and alarm
panel to the C (Common) and NO or NC wire-wrap terminals on the MX410/MX412 rear panel
as required.
Auxiliary alarms 1-4 connect to the MX410/MX412 AUX INPUTS labeled 1-9. These pins detect
ments for the AUX INPUTS.
Table 4-1. AUX Inputs 1-9 Pin List
AUX INPUT
Function
Alarm 1
Default Severity Level
1, 2
3, 4
5, 6
7, 8
9
Critical
Major
Minor
Alert
Alarm 2
Alarm 3
Alarm 4
No Connect
N/A
The alarm severity level can be changed in the Environmental Alarms menu.
After the alarm contact and AUX input connections have been made, install the protective
cover over the wire-wrap headers.
4-4
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
MX410/MX412 System Manual
V.35 Port
The V.35 port is a Nx64k serial interface (up to 1.536 Mbps) with a CCITT V.35, 34-pin
Table 4-2. V.35 Port Pin List
Pin
A
B
C
D
E
Function
Pin
R
Function
Digital Ground
Receive Data to DTE - A1
Transmit Data from DTE - B1
Receive Data to DTE - B1
No Connect
Digital Ground
S
Request To Send (RTS)
Clear To Send (CTS)
Data Set Ready (DSR)
Data Carrier Detect (DCD)
Data Terminal Ready (DTR)
Ring
T
U
V
Receive Clock to DTE - A1
No Connect
F
W
X
H
J
Receive Clock to DTE - B1
Transmit Clock to DTE - A1
Transmit Clock to DTE - B1
No Connect
Y
K
L
No Connect
AA
BB
NN
No Connect
N
P
No Connect
No Connect
Transmit Data from Data Terminal Equipment
(DTE) - A1
DS1 Ports
The DS1 interfaces located on the front panel of the MX410/MX412 are RJ-48 connectors.
Table 4-3. RJ-48 Connector Pin List
Pin
1
Function
RX Ring
2
RX Tip
3
No Connect
TX Ring
4
5
TX Tip
6
No Connect
No Connect
No Connect
7
8
4-6
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Front Panel
Ethernet Ports
The four Ethernet jacks labeled ETHERNET located on the MX410/MX412 front panel provide
LAN access to the Network. From these ports, devices located on the local area network can be
remotely managed. The Ethernet ports have automatic rate detection and perform MDI/MDI-X
crossover detection eliminating the need for a crossover cable. The Ethernet ports can be
accessed using standard CAT 5 cable with an RJ-45 connector. The pin assignments for the
WARNING
The Ethernet and Terminal Server Port 1-4 interfaces must not be
metallically connected to interfaces which connect to the OSP or its
wiring. These interfaces are designed for use as intra-building
interfaces only. The addition of Primary Protectors is not sufficient
protection in order to connect these interfaces metallically to OSP
wiring.
Table 4-4. Ethernet Port Pin List
Pin
1
Function
TX+
2
TX–
3
RX+
4
No Connect
No Connect
RX–
5
6
7
No Connect
No Connect
8
61189500L1-1B
PRELIMINARY
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
MX410/MX412 System Manual
Terminal Server Ports
The four Terminal Server port RS-232 interfaces located on the front panel are used to
remotely connect to RS-232 managed devices.
CAUTION
The 8-pin modular Terminal Server Port 1-4 jacks should never be
connected to a telecommunications network and are intended for
connection to RS-232 data interfaces only.
The Terminal Server ports are accessed by establishing a Telnet session to the MX410/MX412
with the TCP Port Number of the particular port. The pin assignments for each of the RS-232
Table 4-5. Terminal Server Port Pin List
Pin
1
Function
GND
2
No Connect
TXD
3
4
No Connect
RXD
5
6
No Connect
No Connect
No Connect
7
8
ACO Switch
The Alarm Cutoff (ACO) Switch turns off audible and visual alarms connected to the alarm
relays. Pressing the ACO Switch acknowledges alarms.
Craft Port
The DB-9 (RS-232) CRAFT port is used to login and provision the MX410/MX412 through a
VT100 terminal or VT100 terminal emulation software such as HyperTerminal or ProComm
Plus.
4-8
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Front Panel
FXS Port
The FXS port (MX412 only) provides a 2-wire analog interface between a Voice Frequency (VF)
transmission and a signaling facility. The FXS interface provides for simultaneous signaling in
each direction for use with 2-wire off-premises station lines, carrier extended PBX trunks, or
subscriber line foreign exchanges using a loop start signaling system. FXS options are shown
Table 4-6. FXS Options
Mode
Description
Loop Start
PLAR D4
Selects ANSI T1.403 FXS Loop Start mode of operation
Selects Private Line Automatic Ringdown where onhook = 00.
Signaling must match the PLAR unit at the distant end.
PLAR D3
Selects Private Line Automatic Ringdown where onhook = 11.
Signaling must match the PLAR unit at the distant end.
FX Ringdown
PLAR mode of operation that allows for an FXS Loop Start unit on the
distant end.
WARNING
The FXS Port interface must not be metallically connected to inter-
faces which connect to the OSP or its wiring. The FXS interface is
designed for use as an intra-building interface only. The addition of
Primary Protectors is not sufficient protection in order to connect
the FXS interface metallically to OSP wiring.
PSU Slots
The MX410 houses up to two hot-swappable PSUs that can provide power redundancy. At
least one MX410 PSU (P/N 1189501L1) must be inserted into the MX410 for the MX410 to
function. To remove a PSU, remove the screws that hold it in place and carefully pull the PSU
straight out of the MX410. A blank PSU cover (P/N 1189502L1) should be used to cover an
inserted for the MX410 status.
The MX412 contains an internal power supply.
61189500L1-1B
PRELIMINARY
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
MX410/MX412 System Manual
LED Indicators
The LEDs on the front panel of the MX410/MX412 indicate the status of the power, DS1,
Table 4-7. LED Indication
Label
ACT
Status Description
Green Normal operation
Green/Amber (Alternating) Normal operation and console session is open
Amber Software transfer in progress
Red/Amber (Alternating) Self-test failed and console session is open
Red Self-test failed
Flashing Red Unit failure
ALM
Green No critical, major, or minor alarms
Amber Active acknowledged non-critical alarm
Flashing Amber Active acknowledged critical alarm
Red Major or minor alarm in progress
Flashing Red Critical alarm in progress
Green Normal operation
PSU (A/B)
(MX410 only)
Red PSU failure
DS1
(1-4) MX410
Off Port disabled
Green Enabled and normal operation
Amber Locally originated test in progress
Flashing Amber Remotely originated test in progress
Red Non-critical DS1 alarm in progress (for example, AIS)
Flashing Red DS1 LOS (critical DS1 alarm; non-critical system alarm)
(1-12) MX412
1 Second Flashing Red Single code violation or burst of code violations just
occurred
ETHERNET
Off Link not established
Green Link established
(1-4)
Green/Amber (Alternating) Activity on the line
4-10 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Turn-up
TURN-UP
The following sections provide turn-up steps for applying power and logging in to the MX410/
MX412.
Power Up
To power up the MX410/MX412, perform the following steps:
1. Connect the MX410/MX412 to a reliably grounded –48 VDC or ±24 VDC source, which is
electrically isolated from the AC source.
NOTE
A readily accessible disconnect device, such as a rackmount fuse
and alarm panel that is suitably approved and rated should be
incorporated into the fixed wiring.
The branch circuit overcurrent protection should be a slow-blow
fuse or circuit breaker rated 2 amps or greater.
a. Determine which fuse pairs are to supply power to the chassis.
b. Remove the fuses from the A and B slots for the pair.
c. Pull the power connector straight out from the back of the MX410/MX412.
2. Apply power and check voltages.
a. Install appropriate fuses (2 amp slow-blow) in the slots in the fuse and alarm panel that
services the MX410/MX412.
b. Using a voltmeter, verify that the operating voltage is within the specifications for A or
B power feeds.
The A and B input voltage power feeds specifications are as follows:
• –48 VDC systems: –42 VDC to –60 VDC
• –24 VDC systems: –22 VDC to –27 VDC
• +24 VDC systems: +22 VDC to +27 VDC
Place the common (normally black) lead of the voltmeter on the RET A post of the DC
power terminal block and the DC volts (normally red) lead on the PWR A post of the DC
power terminal block.
WARNING
Installing the power connector at this stage provides power to the
MX410/MX412. The pins and connectors on the rear panel and
inside the chassis are powered. Exercise caution to avoid electrical
shock.
61189500L1-1B
PRELIMINARY 4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn-up
MX410/MX412 System Manual
3. Install the power connector for DC power feeds A and B by connecting RET A, PWR A, RET
B, and PWR B to the power connector. PWR refers to respective –48 VDC or ±24 VDC power
sources, while RET refers to respective returns.
a. Insert the power wires into the power connector and tighten the hold-down screws on
the top of the power connector.
b. Insert the power connector into the MX410/MX412 and tighten the two screws on the
front of the power connector.
4. Install at least one PSU into the MX410 front panel PSU A or PSU B slot.
a. Line up the PSU with the guide grooves and carefully insert the unit into the MX410
until it seats all the way into the PSU slot of the MX410.
b. Tighten the thumb screws to secure the PSU in place.
To remove a PSU, remove the thumb screws that hold the PSU in place and carefully pull the
PSU straight out of the MX410.
4-12 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
User Interface
INTRODUCTION
This section provides detailed information on the following:
SYSTEM MANAGEMENT
MX410/MX412 management and provisioning is facilitated by a series of intuitive menus that
are accessible on a computer screen. The MX410/MX412 provides two methods for
management access:
Craft Interface
Connection to the MX410/MX412 menus can be made through the DB-9 connector, labeled
CRAFT, on the front of the MX410/MX412. A DB-9 straight cable is required.
Most personal computers or laptops can run communications software that will emulate a
VT100 terminal. Windows programs such as Terminal or HyperTerminal are two such
examples in the Windows format, but there are many other adequate, commercially available
software packages, virtually all of which allow the PC or laptop to emulate a VT100 terminal.
Certain configuration items must be set on a PC or laptop to act as a VT100 terminal for the
MX410/MX412 as follows:
1. Set the parameters of the communications software to the following settings:
• Data Rate: 115200 bps
• Asynchronous Data Format as follows:
– Eight data bits
61189500L1-1B
PRELIMINARY
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Logging in to the MX410/MX412
MX410/MX412 System Manual
– no parity (none)
– one stop bit
– no flow control
2. Set the PC for direct connect on the appropriate communications port (as opposed to dial
up connection).
3. Plug the male end of the data cable into the MX410/MX412. Make connection to the PC or
laptop as appropriate for the equipment.
Telnet Session
To access the MX410/MX412, use an appropriate Telnet client to access the management
interface of the MX410/MX412 at the configured IP address.
LOGGING IN TO THE MX410/MX412
To logon to the MX410/MX412, perform the following steps:
1. Establish the physical connection to the MX410/MX412 using a craft port session or
enter the default IP address “192.168.100.1” with a subnet mask of “255.255.0.0.” to
establish a Telnet session.
2. Enter the default username “ADMIN” in all capital letters, and press ENTER.
3. Enter the default password “PASSWORD” in all capital letters, and press ENTER.
NOTE
Login username and password fields are case sensitive. The default
values are all uppercase.
5-2
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Structure
MENU STRUCTURE
The menu structure for the MX410/MX412 is a layered menu tree. Each layer of the menu
tree is displayed as a menu or a screen. This section defines the terminology used in
conjunction with the MX410/MX412 menu system.
NOTE
Menu
A menu is a display that provides numbered selections that are used to navigate to related
menus, modify provisioning information, or display information screens. A menu can contain
the following objects:
• Menu Option: A menu option is indicated by a number, which when selected navigates the
display to another menu layer or is used to change the option setting.
• Read-only Field: A read-only field displays information that cannot be changed. The
information displayed in a read-only field can be static or can be automatically updated by
the MX410/MX412.
• Read-write Field: A read-write field displays information that when selected can be
modified.
Screen
A screen is a display that usually indicates the end of a menu tree path. A screen can contain
the following objects:
• Read-only Field: A read-only field displays information that cannot be changed. The
information displayed in a read-only field can be static or can be automatically updated by
the MX410/MX412.
• Read-write Field: A read-write field displays information that when selected can be
modified.
• Keyboard Commands: A keyboard command is a key or combination of keys that are
key(s) and a brief description (i.e., CTRL+A - acknowledge all alarms).
61189500L1-1B
PRELIMINARY
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Layout and Navigation
MX410/MX412 System Manual
MENU LAYOUT AND NAVIGATION
Figure 5-1 illustrates the basic menu layout used in the MX410/MX412 menu system. The
MX410/MX412 Menu Layout figure is general in nature, and not all menus contain all of the
elements shown in the figure.
1
MX410
Active Alarms: CRITICAL MAJOR MINOR ALERT
04/10/05 01:25
MX410
ID:
3
2
Menu Title
1 - Option
2 - Option
3 - Option
4 - Option
5 - Option
6 - Option
: current selection
4
(T)oggle
Selection :
'?' - System Help Screen
5
Figure 5-1. MX410/MX412 Menu Layout
1. Current Date and Time: displays the factory set date and time. The date and time can be
set from the Quick Setup menu or the General Provisioning menu.
2. Alarm Banner: displays a summary of the currently active alarms. If there are any active
Critical Alarms that have not been acknowledged, a flashing reverse video CRITICAL
appears in the alarm banner. If there are no active unacknowledged Critical alarms but
there are currently active acknowledged critical alarms, a solid reverse video CRITICAL
appears in the alarm banner. If there are no active Critical Alarms, nothing will be
displayed for CRITICAL in the alarm banner. Major, Minor, and Alert alarm severities are
displayed in the same manner. Alarm severities are (in descending order): Critical, Major,
Minor, Alert, and Info. Info alarms are not displayed in the menu alarm banner.
3. System ID: A 20-character field that displays the system ID, which can be set from the
Quick Setup menu or the General Provisioning menu.
4. Toggle: pressing the T key toggles between interfaces or shows more information.
5. Selection: An echo field that displays user input. Selection values are applied by pressing
ENTER. Selection values are cleared by pressing the ESC or BACKSPACE key.
Basic menu navigation is accomplished by selecting the desired option number and then
pressing ENTER. To work backward through the menus press the ESC (escape) key. The System
Help screen can be accessed from any MX410/MX412 screen or menu by pressing “?”.
5-4
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Tree
Table 5-1 shows the general keyboard commands for the MX410/MX412.
Table 5-1. MX410/MX412 Keyboard Commands
Keyboard Command
Description
BACKSPACE
This keyboard command is used to delete the character to left of
the cursor during keyboard input.
ENTER (or Return)
This keyboard command is used to terminate input.
ESC
This keyboard command is used to clear partial input data, or if
none, return to previous menu.
CTRL+A (Control and a)
This keyboard command is used to acknowledge all alarms.
This keyboard command is used to logout and disconnect.
This keyboard command is used to refresh the display.
CTRL+C or D (Control and c or d)
CTRL+R (Control and r)
MENU TREE
Menu trees are maps that can be used to locate provisioning options with ease. This
subsection provides a detailed set of menu trees for the MX410/MX412. Some of the menu
trees span multiple pages, signified by the “(Continued)” at the end of the illustration title.
61189500L1-1B
PRELIMINARY
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Tree
MX410/MX412 System Manual
Unit Name
CLEI Code
1. 0 - 133 ft
1. Line Legnth
1. Configuration
2. 133 - 266 ft
3. 266 - 399 ft
4. 399 - 533 ft
5. 533 - 655 ft
6. - 22.5 dB
7. - 15 dB
8. - 7.5 dB
9. - 0 dB
1. B8ZS
2. AMI
Part Number
Serial Number
Product Revision
MAC Address
Code Version
Code Checksum
Boot Version
Boot Checksum
Main Menu
2. Line Coding
1. DS1 Provisioning - Port #1
2. DS1 Provisioning - Port #2
3. DS1 Provisioning - Port #3
4. DS1 Provisioning - Port #4
1. DS1 Ports
1. Enabled
2. Disabled
3. Loopback Detection
4. Framing
1. ESF
2. SF
(MX412 Only)
12. DS1 Provisioning - Port #12
1. Enabled
2. Disabled
5. SNMP Line Status Trap
2. Provisioning
1. Enabled
2. Disabled
6. SNMP Link Status Trap
7. Circuit ID
User Input
1. Enabled
2. Disabled
8. Interface State
1. Enabled
2. Disabled
9. Alarm Pass Thru
Execute (Y, N)
5. Primary TX Timing
6. Secondary TX Timing
1. Internal
2. DS1 1
3. DS1 2
4. DS1 3
5. DS1 4
(MX412 Only)
13. DS1 12
1. Forced On
2. Normal
1. CTS
2. DCD
3. DSR
2. V.35 Port
1. Forced On
2. Normal
1. Forced On
2. Normal
1. DS1 1
2. DS1 2
3. DS1 3
4. DS1 4
1. Choose TO Group
DS1 1 (DS0 1 - 24)
DS1 2 (DS0 1 - 24)
DS1 3 (DS0 1 - 24)
DS1 4 (DS0 1 - 24)
(MX412 Only)
3. Cross-Connect Mapping
12. DS1 12
2. Choose TO DS0
Enter to DS0
1. Enabled
2. Disabled
3. Robbed Bit Signaling
4. Apply Cross-Connect
1. PPPs
(MX412 Only)
DS1 12 (DS0 1 - 24)
1. Choose FROM PPP
2. Choose TO Group
Ports
3. Choose TO DS0 Range
4. Apply Cross-Connect
1. Choose TO Group
2. Choose TO DS0 Range
3. Apply Cross-Connect
2. V.35
1. Choose TO Group
2. Choose TO DS0
3. Mode
3. FXS (MX412 Only)
1. Loop Start
2. PLAR D4
3. PLAR D3
4. FX Ringdown
4. Apply Cross Connect
Bold text indicates default
B
A
Figure 5-2. MX410/MX412 Menu Tree
5-6
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Tree
1. Enabled
2. Disabled
B
1. Terminal State
2. Baud Rate
1. Port 1
2. Port 2
3. Port 3
4. Port 4
4. Terminal Server
1. 9600
2. 19200
3. 38400
4. 57600
5. 115200
3. Telnet Port Number
4. Security
New Port Number
1. Enabled
2. Disabled
5. Username
6. Password
New Username
New Password
1. 9600
1. Craft Port Baud Rate
2. 19200
3. 38400
4. 57600
5. 115200
5. General
2. Date
Enter Date (MM/DD/YYYY)
Enter Time (HH:MM:SS)
Enter Name
3. Time
4. System ID
1. 120 Minutes
2. 90 Minutes
3. 60 Minutes
4. 30 Minutes
5. 15 Minutes
6. 10 Minutes
7. 5 Minutes
5. Auto-Logoff Inactivity Time
8. Disabled
6. Card Reset
Execute <Y,N>
1. Reset All DS1 Provisioning
2. Reset All V.35 Provisioning
3. Reset All 1/0 Mapping
7. Reset to Factory Defaults
4. Reset All Terminal Server Provisioning
5. Reset All General Provisioning
6. Reset All Network Management Provisioning
7. Reset All SNMP Provisioning
8. Reset ALL Factory Defaults
1. Edit User Accounts
8. Security Administration
1. User ID
2. Password
3. Apply
2. Create New User Account
1. Yes
2. No
Challenge Key
3. Restore to Default Accounts
4. Access Tech Support Account
C
Bold text indicates default
Enter Response Key
Figure 5-2. MX410/MX412 Menu Tree (Continued)
61189500L1-1B
PRELIMINARY
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Tree
MX410/MX412 System Manual
C
1. IP Address
New IP Address
1. IP Address
Subnet Mask
1. Ethernet
2. Subnet Mask
3. Apply Settings
6. Network Management
New Subnet Mask
2. Gateway
MAC Address
New Gateway
Eth (1 - 4)
3. Link Speed & Duplex
1. Auto
2. 10 Mbps, Half Duplex
3. 10 Mbps, Full Duplex
4. 100 Mbps, Half Duplex
5. 100 Mbps, Full Duplex
Functional Link Speed & Duplex
Link Status
1. BCP
2. IPCP
1. BCP/IPCP
2. PPP BCP/IPCP
PPP (1 - 4)
1. IP Address
2. IP Address
New IP Address
2. Subnet Mask
3. Apply Settings
Subnet Mask
Far End IP Address
New Subnet Mask
1. Enabled
2. Disabled
3. SNMP Link Status Trap
LCP Status
BCP/IPCP Status
1. Enabled
2. Disabled
1. State
3. DHCP
2. Network
New Network / Mask
New Default Router
New DNS Router
3. Default Router
4. DNS Router
5. Address Range
6. Lease Time
New Range (begin-end)
New Lease Time (d:h:m)
1. Enabled
2. Disabled
1. SNMP State
7. SNMP
2. Trap Host 1 IP
3. Trap Host 2 IP
4. Trap Host 3 IP
5. Trap Host 4 IP
1. Trap Host IP
2. Trap Host Method
3. Trap Host Status
1. Enabled
2. Disabled
6. SNMP Traps
7. System Name
New System ID
New Location
8. System Location
9. System Contact
10. Read Community
11. Write Community
New Contact
New Community
New Community
1. SCA TFTP Server
2. Remote Filename
Enter SCA TFTP Server
8. System Configuration Archive (SCA)
Enter Remote SCA Filename
1. All
2. Data Path Only
3. All/Data Path Only
4. Perform SCA Save
5. Perform SCA Restore
6. Auto Save Time
9. Save Provisioning
10. Auto Save
Enter Auto Save Time (Day HH:MM)
1. Enabled
2. Disabled
7. Auto Save
Bold text indicates default
Figure 5-2. MX410/MX412 Menu Tree (Continued)
5-8
PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Tree
1. Choose FROM PPP
2. Choose TO Group
A
1. PPPs
3. Choose TO DS0 Range
4. Apply Cross-Connect
3. Quick Setup
1. Choose TO Group
2. Choose TO DS0 Range
3. Apply Cross-Connect
2. V.35
1. Choose TO Group
2. Choose TO DS0
3. Mode
3. FXS (MX412 Only)
1. Loop Start
2. PLAR D4
3. PLAR D3
4. FX Ringdown
4. Apply Cross Connect
New System Name
3. System ID
1. IP Address
New IP Address
4. IP Address / Subnet Mask
2. Subnet Mask
3. Apply Settings
New Subnet Mask
1. DS1 1
2. DS1 2
3. DS1 3
4. DS1 4
5. Default Gateway
6. Date
New Gateway
Enter Date (MM/DD/YYYY)
7. Time
Enter Time (HH:MM:SS)
1. Choose TO Group
2. Choose TO DS0
(MX412 Only)
DS1 1 (DS0 1 - 24)
DS1 2 (DS0 1 - 24)
DS1 3 (DS0 1 - 24)
DS1 4 (DS0 1 - 24)
12. DS1 12
8. Cross-Connect Setup
Enter to DS0
1. Enabled
2. Disabled
3. Robbed Bit Signaling
4. Apply Cross-Connect
(MX412 Only)
DS1 12 (DS0 1 - 24)
1. Choose FROM PPP
2. Choose TO Group
1. PPPs
4. Status
3. Choose TO DS0 Range
4. Apply Cross-Connect
Ports
1. Choose TO Group
2. Choose TO DS0 Range
3. Apply Cross-Connect
2. V.35
1. Choose TO Group
2. Choose TO DS0
3. Mode
3. FXS (MX412 Only)
1. Loop Start
2. PLAR D4
3. PLAR D3
4. FX Ringdown
4. Apply Cross Connect
D
Bold text indicates default
Figure 5-2. MX410/MX412 Menu Tree (Continued)
61189500L1-1B
PRELIMINARY
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Tree
MX410/MX412 System Manual
D
DS1 Ports
1. #1
2. #2
3. #3
4. #4
1. Data Mode
2. Payload
3. Line
5. Test
1. Loopback
Pattern
DS1 x Status
Execute (Y, N)
4. Inward
5. Reset ALL Tests
5. Dual
6. Remote FDL Line
7. Remote Inband Line (CSU)
8. Remote FDL Payload
1. 120 Minutes
2. 90 Minutes
3. 60 Minutes
4. 30 Minutes
5. 15 Minutes
6. 10 Minutes
7. 5 Minutes
8. Disabled
6. Loopback Timeout
1. QRSS
2. All Ones
3. All Zeros
4. 511
Execute (Y, N)
9. Pattern Test
5. 2047
6. 2^15-1
7. 2^20-1
1. Daily PM Table
1. ES-L Threshold
1. Value
6. Performance Monitoring
2. Quarter Hour PM Table
3. Daily PM Thresholds
4. Quarter Hour PM Thresholds
5. Clear PM Data
2. CV-P Threshold (ESF mode)
3. CV-P Threshold (SF mode)
4. ES-P Threshold
2. Enable/Disable
5. SES-P Threshold
6. SES-P Threshold
7. CSS-P Threshold
8. UAS-P Threshold
1. Master Log
7. System Alarms
1. Aux #1 Input
2. Aux #2 Input
1. Severity
2. Environmental Alarms
2. Description
3. Aux #3 Input
4. Aux #4 Input
5. Power Feed A
6. Power Feed B
7. PSU A (MX410 Only)
8. PSU B (MX410 Only)
1. Ascending
2. Descending
3. Alarm Chronology
1. X-MODEM
2. TFTP
1. Initiate Transfer
2. Card Reset
Execute <Y,N>
8. Code Download
1. TFTP Server
Enter TFTP Server
2. Remote Filename
3. Initiate Transfer
4. Card Reset
Enter Remote Filename
9. Logoff
Execute <Y,N>
Bold text indicates default
Figure 5-3. MX410/MX412 Menu Tree (Continued)
5-10 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
MENU DESCRIPTIONS
Each Main menu item has several functions and submenus that identify and provide access to
specific operations and parameters.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR MINOR
ID:
Main Menu
1 - Configuration
2 - Provisioning
3 - Quick Setup
4 - Status
5 - Test
6 - Performance Monitoring
7 - System Alarms
8 - Code Download
9 - Logoff
Selection :
'?' - System Help Screen
Figure 5-4. MX410/MX412 Main Menu
Table 5-2. MX410/MX412 Main Menu Options
Option
Description
Configuration
Provisioning
Quick Setup
Status
Function
1
2
3
4
5
6
Test
Performance Monitoring
7
8
System Alarms
Code Download
9
Logoff
This option is used to end an MX410/MX412 menus session.
No further menus, screens, or confirmation dialog boxes are
presented.
61189500L1-1B
PRELIMINARY 5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Configuration Screen
Information such as Code Version changes as upgrades are performed. The CLEI Code and
Part Number can be used to search for related information on the ADTRAN website or to order
additional parts. Some information from this menu may be required when calling the ADTRAN
Technical Support.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Configuration
Unit Name
CLEI Code
: MX410
: M3M1310BRA
: 1189500L1
: DVTUUTNXXX
: B
Part Number
Serial Number
Product Revision
MAC Address
Code Version
Code Checksum
Boot Version
Boot Checksum
: XX:XX:XX:XX:XX:XX
: B01
: ADCDEFGH
: B03
: 7C22
'?' - System Help Screen
Figure 5-5. Configuration Screen
5-12 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Table 5-3. MX410/MX412 Configuration Screen Fields
Field
Description
Unit Name
CLEI Code
This field displays the MX410/MX412 unit name.
This field displays the Common Language Equipment Identifier (CLEI) code of the
MX410/MX412.
Part Number
This field displays the MX410/MX412 part number.
Serial Number
Product Revision
This field displays the serial number of the MX410/MX412.
This field displays the hardware product assembly revision of the MX410/
MX412.
MAC Address
This field displays the factory programmed Media Access Control (MAC) or phys-
ical layer address for the MX410/MX412.
Code Version
This field displays the current firmware revision level of the MX410/MX412.
Code Checksum
This field displays the checksum of the current firmware revision level of the
MX410/MX412.
Boot Version
This field displays the Boot ROM software revision code of the MX410/MX412.
Boot Checksum
This field displays the checksum of the Boot ROM software revision code of the
MX410/MX412.
61189500L1-1B
PRELIMINARY 5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Provisioning Menu
options.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR MINOR
ID:
Provisioning
1 - DS1 Ports
2 - V.35 Port
3 - Cross-Connect Mapping
4 - Terminal Server Ports
5 - General
6 - Network Management
7 - SNMP
8 - System Configuration Archive (SCA)
9 - Save Provisioning
10 - Auto Save
: Enabled
Selection :
'?' - System Help Screen
Figure 5-6. Provisioning Menu
5-14 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Table 5-4. Provisioning Menu Options
Option Description
Function
1
2
3
DS1 Ports
V.35 Port
4
5
6
Terminal Server Ports
General
Network Management
SNMP
7
8
System Configuration
Archive (SCA)
9
Save Provisioning
Auto Save
This option is used to save current network settings.
10
This option is used to automatically save current network
settings at timed intervals.
61189500L1-1B
PRELIMINARY 5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
DS1 Ports Menu
framing, SNMP line status trap, SNMP link status trap, circuit ID, interface state, and alarm
pass thru information for DS1 ports 1-4 (1-12 on the MX412), as well as timing information.
Selection of an option invokes other menus to set the option variables. The Toggle command
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
DS1 Ports
Line
Length
Line
Coding
B8ZS
Loopback
SNMP Line
SNMP Link
Detect
Enabled
Enabled
Enabled
Enabled
Framing
ESF
ESF
Status Trap
Disabled
Disabled
Disabled
Disabled
Status Trap
Enabled
Enabled
1 -
2 -
3 -
4 -
0 - 133 ft
0 - 133 ft
0 - 133 ft
0 - 133 ft
B8ZS
B8ZS
B8ZS
ESF
ESF
Enabled
Enabled
5 - Primary TX Timing - Internal
6 - Secondary TX Timing - Internal
(T)oggle for more
'?' - System Help Screen
Selection :
Figure 5-7. DS1 Ports Menu
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
DS1 Ports
Circuit ID
Interface State
Alarm Pass Thru
1 -
2 -
3 -
4 -
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
5 - Primary TX Timing - Internal
6 - Secondary TX Timing - Internal
(T)oggle for more
'?' - System Help Screen
Selection :
Figure 5-8. DS1 Ports Menu - Toggled
5-16 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
DS1 Provisioning Menu
loopback detection, framing, SNMP line status trap, SNMP link status trap, circuit ID,
interface state, and alarm pass thru information for the selected DS1 port.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
DS1 Provisioning - Port #1
1 - Line Length
2 - Line Coding
: 0 - 133 ft
: B8ZS
3 - Loopback Detection
4 - Framing
: Enabled
: ESF
5 - SNMP Line Status Trap
6 - SNMP Link Status Trap
7 - Circuit ID
: Disabled
: Enabled
:
8 - Interface State
9 - Alarm Pass Thru
: Enabled
: Disabled
Selection :
'?' - System Help Screen
Figure 5-9. DS1 Provisioning Menu
5-18 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Table 5-6. DS1 Provisioning Menu Options
Option Description
Function
1
Line Length
This option sets the line length (line build out) for each port inter-
face according to the distance from the MX410/MX412 to the other
device.
Options for line length are as follows:
• 1 - Set line length from 0 to 133 feet
• 2 - Set line length from 133 to 266 feet
• 3 - Set line length from 266 to 399 feet
• 4 - Set line length from 399 to 533 feet
• 5 - Set line length from 533 to 655 feet
• 6 - –22.5 dB
• 7 - –15 dB
• 8 - –7.5 dB
• 9 - 0 dB
2
Line Coding
This option sets the line code for each individual port interface to
match the connected device.
Options for line coding are as follows:
• 1 - AMI
• 2 - B8ZS
3
4
Loopback Detection
Framing
This option enables or disables whether a port responds to CSU
and FDL loopback requests coming from the network.
This option sets the framing. Options for framing are as follows:
• 1 - ESF (Extended Super Frame)
• 2 - SF (Super Frame).
5
6
7
SNMP Line Status
Trap
This option enables or disables the SNMP line status trap state.
SNMP Link Status
Trap
This option enables or disables the SNMP link status trap state.
Circuit ID
This option contains a user-configurable text string field to name
the selected port. This field accepts up to 32 alphanumeric charac-
ters, including spaces and special characters.
8
9
Interface State
This option is viewed using the Toggle command and sets the
interface state to either enabled or disabled.
Alarm Pass Thru
This option enables or disables semi-transparency for visibility
through the cross connect to remote devices. This option enables
the selected DS1 to transmit RAI when any cross-connected DS1 is
in alarm or receiving RAI.
Alarm Pass Thru
61189500L1-1B
PRELIMINARY 5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Primary Timing Mode Menu
the selected DS1 port (1-4 on the MX410 and 1-12 on the MX412).
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
Primary Timing Mode : Internal
1 - Internal
2 - DS1 1
3 - DS1 2
4 - DS1 3
5 - DS1 4
Selection :
'?' - System Help Screen
Figure 5-10. Primary Timing Mode Menu
Table 5-7. Primary Timing Mode Menu Options
Option Description
Function
1
2
3
4
5
Internal
DS1 1
DS1 2
DS1 3
DS1 4
This option sets the timing mode to internal.
This option sets the timing mode to DS1 1.
This option sets the timing mode to DS1 2.
This option sets the timing mode to DS1 3.
This option sets the timing mode to DS1 4.
CAUTION
The entire MX410/MX412 is timed from a single source and all
transmitters are synchronized. Any device attached to the MX410/
MX412 should be placed in loop or line timing mode, unless it is
providing timing. If an attached device is providing timing, the
MX410/MX412 must be configured to use this interface as its pri-
mary timing source. If the MX410/MX412 is set for internal timing,
all devices connected to it must be set to loop or line timing.
5-20 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Secondary Timing Mode Menu
for the selected DS1 port (1-4 on the MX410 and 1-12 on the MX412).
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
Primary Timing Mode : Internal
1 - Internal
2 - DS1 1
3 - DS1 2
4 - DS1 3
5 - DS1 4
Selection :
'?' - System Help Screen
Figure 5-11. Secondary Timing Mode Menu
Table 5-8. Secondary Timing Mode Menu Options
Option Description
Function
1
2
3
4
5
Internal
DS1 1
DS1 2
DS1 3
DS1 4
This option sets the timing mode to internal.
This option sets the timing mode to DS1 1.
This option sets the timing mode to DS1 2.
This option sets the timing mode to DS1 3.
This option sets the timing mode to DS1 4.
CAUTION
The entire MX410/MX412 is timed from a single source and all
transmitters are synchronized. Any device attached to the MX410/
MX412 should be placed in loop or line timing mode, unless it is
providing timing. If an attached device is providing timing, the
MX410/MX412 must be configured to use this interface as its pri-
mary timing source. If the MX410/MX412 is set for internal timing,
all devices connected to it must be set to loop or line timing.
61189500L1-1B
PRELIMINARY 5-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
V.35 Port Menu
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
V.35 Port
1 - CTS
2 - DCD
3 - DSR
: Forced On
: Forced On
: Normal
Selection :
'?' - System Help Screen
Figure 5-12. V.35 Port Menu
Table 5-9. V.35 Port Menu Options
Option Description
Function
1
2
3
CTS
DCD
DSR
This option sets the CTS (Clear To Send) settings. Options are as
follows:
• Normal: The setting matches RTS settings.
• Forced On: This setting forces CTS to be active.
This option sets the DCD (Data Carrier Detect) settings. Options
are as follows:
• Normal: The setting matches the status of the connected DS1.
• Forced On: This setting forces DCD to be active.
This option sets the DSR (Data Set Ready) settings. Options are as
follows:
• Normal: The setting follows DTR settings.
• Forced On: This setting forces DSR to be active.
5-22 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Cross-Connect Mapping Menu
The Cross-Connect Mapping menu is used to display DS0 information for the four DS1 ports
(12 ports on the MX412), as well as FXS (MX412 only), PPP, and V.35 settings. The Cross-
The Toggle command is used to view DS1 2, DS1 3, DS1 4, PPP, and V.35 data. All of the DS1
toggle menus have identical options, and all of the 24 DS0s have identical options for the
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
DS1 1 - Huntsville T1
1 - DS0 #1 = DS1 1 DS0 #2
2 - DS0 #2 = DS1 1 DS0 #1
3 - DS0 #3 =
13 - DS0 #13 =
14 - DS0 #14 =
15 - DS0 #15 =
16 - DS0 #16 =
17 - DS0 #17 =
18 - DS0 #18 =
19 - DS0 #19 =
20 - DS0 #20 =
21 - DS0 #21 =
22 - DS0 #22 =
23 - DS0 #23 =
24 - DS0 #24 =
4 - DS0 #4 =
5 - DS0 #5 =
6 - DS0 #6 =
7 - DS0 #7 =
8 - DS0 #8 =
9 - DS0 #9 =
10 - DS0 #10 =
11 - DS0 #11 =
12 - DS0 #12 =
(T)oggle View (DS1 2, DS1 3, DS1 4, Ports)
Selection :
25 - Map Multiple DS0's
'?' - System Help Screen
Figure 5-13. Cross-Connect Mapping Menu
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Cross-Connect Mapping
Ports
1 - PPPs
PPP 1 = DS1 4 DS0 #1
2 - V.35 =
3 - FXS
=
(T)oggle View (DS1 1, DS1 2, DS1 3, DS1 4)
Selection :
'?' - System Help Screen
Figure 5-14. Cross-Connect Mapping - Ports Menu
61189500L1-1B
PRELIMINARY 5-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Table 5-10. Cross-Connect Mapping Menu Options
Option Description
1-24 DS0 1-24 connections
Function
These options invoke the Change Cross-Connect Mapping menu
which is used to provision the cross-connect settings for the
selected DS1 port. Options are as follows:
• 1. Choose TO Group (for DS1 1 through DS1 4/DS1 12)
• 2. Choose TO DS0: (enter a value)
• 3. Robbed Bit Signaling: select Enabled or Disabled
• 4. Apply Cross-Connect: applies the selections made from the
Change Cross-Connect Mapping menu.
25
Map Multiple DS0's
This option invokes the Change Cross-Connect Mapping menu
which is used to provision the cross-connect settings for multiple
DS0s at the same time. Options are as follows:
• 1. Choose FROM DS0 Range: enter a range
• 2. Choose TO Group (for DS1 1 through DS1 4/DS1 12)
• 3. Choose TO DS0 Range: enter a range
• 4. Robbed Bit Signaling: select Enabled or Disabled
• 5. Apply Cross-Connect: applies the selections made from the
Change Cross-Connect Mapping menu to all DS0s in the
range entered.
Cross-Connect Mapping - Ports
1
PPPs
This option invokes the Change Cross-Connect Mapping menu,
which is used to provision the PPP ports. Options are as follows:
• 1. Choose FROM PPP (for PPP 1 through PPP 4)
• 2. Choose TO Group (for DS1 1 through DS1 4)
• 3. Choose TO DS0 Range: enter a range
• 4. Apply Cross-Connect
2
3
V.35
This option invokes the Change Cross-Connect Mapping menu,
which is used to provision the V.35 port. Options are as follows:
• 1. Choose TO Group (for DS1 1 through DS1 4/DS1 12)
• 2. Choose TO DS0 Range: enter a range
• 3. Apply Cross-Connect
FXS (MX412 only)
This option invokes the Change Cross-Connect Mapping menu
which is used to provision the FXS port. Options are as follows:
• 1. Choose TO Group (for DS1 1 through DS1 12)
• 2. Choose TO DS0 Range: enter a range
• 3. Mode: Select Loop Start, PLAR D4, PLAR D3, or FX
these options.
• 4. Apply Cross-Connect
5-24 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Terminal Server Ports Menu
Port 4 for provisioning.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Terminal Server Ports
1 - Port 1
2 - Port 2
3 - Port 3
4 - Port 4
Selection :
'?' - System Help Screen
Figure 5-15. Terminal Server Ports Menu
Table 5-11. Terminal Server Ports Menu Options
Option Description
Function
1
2
3
4
Port 1
Port 2
Port 3
Port 4
61189500L1-1B
PRELIMINARY 5-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Terminal Server Port (1 - 4) Menu
selected on the (previous) Terminal Server Ports menu.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Terminal Server Port 1
1 - Terminal State
2 - Baud Rate
: Enabled
: 9600
: 2023
3 - Telnet Port Number
4 - Security
5 - Username
: Enabled
: port 1
: password
6 - Password
Selection :
'?' - System Help Screen
Figure 5-16. Terminal Server Port 1 Menu
Table 5-12. Terminal Server Port Menu Options
Option Description
Function
1
2
Terminal State
Baud Rate
This option enables or disables the terminal state.
This option sets the terminal server baud rate. Options are as
follows:
• 9600
• 19200
• 38400
• 57600
• 115200
3
4
5
Telnet Port Number
Security
This option is used to enter a new Telnet port number.
This option is used to enable or disable terminal port security.
Username
This option is used to assign a username to the selected port
number for use when security is enabled.
6
Password
This option is used to assign a password to the selected port
number for use when security is enabled.
5-26 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
General Provisioning Menu
the date, time, system ID, auto-logoff inactivity time, to reset the MX410/MX412, and to
handle security administration.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
General Provisioning
1 - Craft Port Baud Rate
2 - Date
: 115200
: 04/22/2005
: 18:50:47
: MX410
3 - Time
4 - System ID
5 - Auto-Logoff Inactivity Time
: 15 minutes
6 - Card Reset
7 - Reset To Factory Defaults
8 - Security Administration
Selection:
'?' - System Help Screen
Figure 5-17. General Provisioning Menu
Table 5-13. General Provisioning Menu Options
Option Description
Function
1
Craft Port Baud Rate
This option sets the craft port baud rate. Options are as follows:
• 9600
• 19200
• 38400
• 57600
• 115200.
2
3
4
Date
This option is used to enter the date.
This option is used to enter the time.
Time
System ID
This option defines the alphanumeric name assigned to the
MX410/MX412.
61189500L1-1B
PRELIMINARY 5-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Table 5-13. General Provisioning Menu Options (Continued)
Option Description
Function
5
Auto-Logoff Inactivity
Time
This option defines when a menu session automatically termi-
nates due to inactivity. The default setting is 15 Minutes. Options
are as follows:
• 120 Minutes
• 90 Minutes
• 60 Minutes
• 30 Minutes
• 15 Minutes
• 10 Minutes
• 5 Minutes
• Disabled
6
7
Card Reset
This option forces the MX410/MX412 to reset.
Reset to Factory
Defaults
This option is used to reset factory defaults by logical groups, or
reset all factory defaults at once.
8
Security
Administration
This option invokes the Security Administration menu, which is
used to manage accounts. Options are as follows:
• Users Currently Logged On: This option displays active
usernames, access method and address, and the login time.
• Edit User Accounts: This option is used to edit user accounts.
• Create New User Account: This option is used to create new
user accounts. Options are as follows:
– User ID: This option is used to enter a new username.
– Password: This option is used to enter a new password.
– Access Rights: This option is used to select Read, Test,
Read/Write, or Admin access privileges.
– Apply: This option saves the new user account
information.
• Restore to Default Accounts: This option is used to restore the
accounts default and deletes all previous information by
selecting Yes or No.
• Access Tech Support Account: This option is used to access
the technical support account information by entering a
Response Key.
5-28 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Network Management Menu
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
Network Management
1 - Ethernet
2 - PPP BCP/IPCP
3 - DHCP
Selection :
'?' - System Help Screen
Figure 5-18. Network Management Menu
Table 5-14. Network Management Menu Options
Option Description
Function
1
2
3
Ethernet
PPP BCP/IPCP
DHCP
61189500L1-1B
PRELIMINARY 5-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Ethernet Menu
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Ethernet
1 - IP Address
Subnet Mask
2 - Gateway
MAC Address
: 192.168.100.1
: 255.255.0.0
: 192.168.1.1
: XX:XX:XX:XX:XX:XX
Eth 1
3 - Link Speed & Duplex : Auto
Functional Link Speed & Duplex : Unknown
Link Status
: Down
(T)oggle Between Interfaces
Selection :
'?' - System Help Screen
Figure 5-19. Ethernet Menu
Table 5-15. Ethernet Menu Options
Option Description
Function
1
IP Address
This option invokes another menu which is used to enter the IP
Address and the Subnet Mask for the MX410/MX412. The IP
Address is written in the format XXX.XXX.XXX.XXX, where each 3-
digit field has a value between 1 and 255.
N/A
Subnet Mask
This field displays the Subnet Mask. A subnet mask is used to
reduce the traffic on each subnetwork by confining traffic to only
the subnetwork for which it was intended. A subnet mask makes
the entire network more manageable. In effect, each subnet func-
tions as though it were an independent network, keeping local traf-
fic local and forwarding traffic to another subnet only if the address
of the data is external to the subnet. The Subnet Mask is written in
the format XXX.XXX.XXX.XXX, where each 3-digit field has a value
between 1 and 255.
2
Gateway
This option invokes another menu which is used to enter the
address of the default gateway/router between the internal
network and the external network. The Gateway address is written
in the format XXX.XXX.XXX.XXX, where each 3-digit field has a
value between 1 and 255.
5-30 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Table 5-15. Ethernet Menu Options (Continued)
Option Description
Function
MAC Address
This read-only field displays the Medium Access Control (MAC)
Address. MAC Addresses are location-independent (programmed
into the card at manufacture, they relocate when the card does).
MAC Addresses are contained in the headers of packets and are
used to filter and forward packets.
Eth (1-4)
3
Link Speed & Duplex This option invokes another menu which is used to select the data
rate setting for Ethernet Port (1-4) on the front panel of the
MX410/MX412. Options are as follows:
• 1 - Auto
• 2 - 10 Mbps, Half Duplex
• 3 - 10 Mbps, Full Duplex
• 4 - 100 Mbps, Half Duplex
• 5 - 100 Mbps, Full Duplex
N/A
N/A
Functional Link
Speed & Duplex
This read-only field displays the actual data rate of the port.
Link Status
This read-only field displays the status of the network as being
either Up or Down.
61189500L1-1B
PRELIMINARY 5-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
PPP BCP/IPCP Menu
Point-to-Point Protocol (PPP) is commonly used for LAN extension and Remote management
connectivity. PPP can use one of two upper layer protocols:
• BCP (Bridge Control Protocol): This protocol routes packets based on MAC addresses and
allows broadcast traffic to be passed over the PPP link(s). This protocol enables true LAN
Extension to be completed. Any device on the LAN can communicate with any other device
with the least amount of configuration by the user.
• IPCP (IP Control Protocol): This protocol is used to for the user to assign an IP address to
each interface of the MX410/MX412. This enables dynamic routing of packets based on
the IP address and prohibits broadcast traffic from being passed over the PPP link(s). This
protocol requires more IP knowledge and configuration of each device on the network to
ensure proper IP routing, Default gateway configuration, as well as avoiding conflicts of
networks and DHCP configurations. When IPCP is enabled, RIP v2 is the routing protocol
used by the MX410/MX412.
If using PPP, the T1/FT1 carrying the PPP link should be configured to ESF and B8ZS.
CAUTION
Only one PPP link can be connected between two devices. If more
than one PPP link is connected between two devices, it creates an
Ethernet LOOP and causes a Packet Storm across the entire
Ethernet network.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR MINOR
ID:
PPP BCP/IPCP
1 - BCP/IPCP
: BCP
PPP 1
2 - IP Address
Subnet Mask
: unknown
: unknown
Far End IP Address
: unknown
: Enabled
3 - SNMP Link Status Trap
LCP Status
BCP/IPCP Status
: Down
: Down
(T)oggle Between Interfaces
Selection :
'?' - System Help Screen
Figure 5-20. PPP BCP/IPCP Menu
5-32 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Table 5-16. PPP BCP/IPCP Menu Options
Option Description
Function
1
BCP/IPCP
This option is used to select either BCP (Bridge Control Protocol) or
IPCP (IP Control Protocol for routing).
PPP (1-4)
2
IP Address
This option invokes another menu which is used to enter the IP
Address, the Subnet Mask for the PPP. The IP Address is written in
the format XXX.XXX.XXX.XXX, where each 3-digit field has a value
between 1 and 255.
N/A
Subnet Mask
This field displays the PPP Subnet Mask. The Subnet Mask is writ-
ten in the format XXX.XXX.XXX.XXX, where each 3-digit field has
a value between 1 and 255.
N/A
3
Far End IP Address
This read-only field displays the far-end device IP address.
SNMP Link Status
Trap
This option invokes another menu which is used to either enable or
disable the SNMP link status trap.
N/A
LCP Status
This read-only field displays the Link Control Protocol (LCP) status
as Up or Down.
BCP/IPCP Status
This read-only field displays the BCP/IPCP status as Up or Down.
61189500L1-1B
PRELIMINARY 5-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
DHCP Server Menu
to provision DHCP server connections.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
DHCP Server
1 - State
2 - Network
: Disabled
: Not Set/Not Set
: Not Set
: Not Set
3 - Default Router
4 - DNS Router
5 - Address Range : 0.0.0.0-255.255.255.255
6 - Lease Time (d:h:m) : 0:0:0
Selection :
'?' - System Help Screen
Figure 5-21. DHCP Server Menu
Table 5-17. DHCP Server Menu Options
Option Description
Function
1
2
State
This option is used to enable or disable the DHCP server.
Network
This option invokes another menu which is used to enter a network
address and mask (scope of DHCP server).
3
4
5
6
Default Router
DNS Router
This option invokes another menu which is used to enter the new
DHCP default router address.
This option invokes another menu which is used to enter the new
DHCP DNS router address.
Address Range
Lease Time (d:h:m)
This option invokes another menu which is used to enter the range
of leased addresses.
This option invokes another menu which is used to enter the
expiration of the lease assigned to the DHCP server time in days,
hours, and minutes.
5-34 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
SNMP Menu
provision SNMP information.
MX410
SNMP
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR MINOR
ID:
1 - SNMP State
: Disabled
: 0.0.0.0
: 0.0.0.0
: 0.0.0.0
: 0.0.0.0
: Disabled
: MX410
2 - Trap Host 1 IP
3 - Trap Host 2 IP
4 - Trap Host 3 IP
5 - Trap Host 4 IP
6 - SNMP Traps
7 - System Name
8 - System Location :
9 - System Contact
10 - Read Community
11 - Write Community : private
:
: public
Selection :
'?' - System Help Screen
Figure 5-22. SNMP Menu
Table 5-18. SNMP Menu Options
Option Description
Function
1
SNMP State
This option sets the SNMP state to enabled or disabled. When
disabled, the MX410/MX412 ignores all incoming SNMP packets,
and does not transmit SNMP packets
2
Trap Host 1 IP
This option invokes another menu which is used to enter the Trap
Host 1 IP address of an SNMP manager to which the MX410/
MX412 sends traps, the method (version 1 traps or version 2 notifi-
cations), and enable or disable the trap host.
3
4
Trap Host 2 IP
Trap Host 3 IP
This option invokes another menu which is used to enter the Trap
Host 2 IP address of an SNMP manager to which the MX410/
MX412 sends traps, the method (version 1 traps or version 2 notifi-
cations), and enable or disable the trap host.
This option invokes another menu which is used to enter the Trap
Host 3 IP address of an SNMP manager to which the MX410/
MX412 sends traps, the method (version 1 traps or version 2 notifi-
cations), and enable or disable the trap host.
61189500L1-1B
PRELIMINARY 5-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Table 5-18. SNMP Menu Options (Continued)
Option Description
Function
5
Trap Host 4 IP
This option invokes another menu which is used to enter the Trap
Host 4 IP address of an SNMP manager to which the MX410/
MX412 sends traps, the method (version 1 traps or version 2 notifi-
cations), and enable or disable the trap host.
6
7
SNMP Traps
This option displays the user-defined system name and invokes
another menu which is used to input alphanumeric characters
that identify the name of the MX410/MX412.
System Name
This option displays the user-defined system name and invokes
another menu which is used to input alphanumeric characters
that identify the name of the MX410/MX412.
8
System Location
System Contact
Read Community
This option displays the user-defined system location and invokes
another menu which is used to input alphanumeric characters
that identify the physical location of the MX410/MX412.
9
This option displays the user-defined system contact and invokes
another menu which is used to input the name of personnel to
contact about the MX410/MX412.
10
This option invokes another menu which is used to enter the
authentication strings used for SNMP management. Input a value
that matches the MX410/MX412 to the SNMP manager for read
privileges.
11
Write Community
This option invokes another menu which is used to enter the
authentication strings used for SNMP management. Input a value
that matches the MX410/MX412 to the SNMP manager for write
privileges.
5-36 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
SCA Update Menu
SCA information.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
SCA Update
1 - SCA TFTP Server
2 - Remote Filename
: 0.0.0.0
:
3 - All/Data Path Only : All Provisioning
4 - Perform SCA Save
5 - Perform SCA Restore
6 - Auto Save Time
7 - Auto Save
: Wed 10:35
: Disabled
Awaiting download.
Selection :
'?' - System Help Screen
Figure 5-23. SCA Update Menu
Table 5-19. SCA Update Menu Options
Option Description
Function
1
2
3
SCA TFTP Server
This option is used to enter the IP address where the SCA server
resides.
Remote Filename
This option is used to enter the name of a file to save to or restore
from the SCA server.
All/Data Path Only
This option is used to enter select amount of data to be save SCA
server.
4
5
6
Perform SCA Save
Perform SCA Restore
Auto Save Time
This option is used to initiate an upload to save provisioning.
This option is used to initiate a download to restore provisioning.
This option is used to enter the date and time to automatically
perform an auto save.
7
Auto Save
This option is used to automatically save SCA provisioning data at
a user-specified date and time by selecting enabled or disabled.
61189500L1-1B
PRELIMINARY 5-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Quick Setup Menu
To simplify the installation process, all of the basic configuration options necessary to setup
Quick Setup menu allows configuration of such items as DS0 drop assignments, as well as
system date, time, and IP Address information.
MX410
MM/DD/YY HH:MM
MX410
Unacknowledged Alarms: CRITICAL
ID:
Quick Setup
Ports
1 - PPPs
PPP 1 =
2 - V.35 =
System
3 - System ID
4 - IP Address
Subnet Mask
5 - Default Gateway
6 - Date
: 192.168.100.1
: 255.255.0.0
: 192.168.1.1
7 - Time
8 - Cross-Connect Mapping
Selection :
'?' - System Help Screen
Figure 5-24. Quick Setup Menu
Table 5-20. Quick Setup Menu Options
Option Description
Function
Ports
1
PPPs
This option is used to provision the PPP ports. Options are as
follows:
• Choose FROM PPP (for PPP 1 through PPP 4)
• Choose TO Group (for DS1 1 through DS1 4)
• Choose TO DS0 Range (enter a range of DS0s)
• Apply Cross-Connect
2
V.35
This option is used to provision the V.35 port. Options are as
follows:
• Choose TO Group (for DS1 1 through DS1 4)
• Choose TO DS0 Range (enter a range of DS0s)
• Apply Cross-Connect
5-38 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Table 5-20. Quick Setup Menu Options (Continued)
Option Description
Function
3
FXS (MX412 only)
This option is used to provision the FXS port. Options are as
follows:
• Choose TO Group (for DS1 1 through DS1 4)
• Choose TO DS0 Range: enter a range
• Mode: Select Loop Start, PLAR D4, PLAR D3, or FX Ringdown.
• Apply Cross-Connect
System
3
4
System ID
IP Address
This option is used to assign a new system ID.
This option is used to enter the IP Address for the MX410/MX412.
The IP Address is written in the format XXX.XXX.XXX.XXX, where
each 3-digit field has a value between 1 and 255.
N/A
5
Subnet Mask
This option is used to enter the subnet mask, written in the format
XXX.XXX.XXX.XXX, where each 3-digit field has a value between 1
and 255.
Default Gateway
This option is used to enter the default gateway. The Gateway
address is written in the format XXX.XXX.XXX.XXX, where each 3-
digit field has a value between 1 and 255.
6
7
8
Date
Time
This option is used to enter the date.
This option is used to enter the time.
Cross-Connect
Mapping
This is another path to the Cross-Connect Mapping Menu shown in
61189500L1-1B
PRELIMINARY 5-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Status Screen
Ethernet Ports, PPP, Timing, and the Power Feed.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
DS1 Ports
ID:
Status
PPP Interfaces
State
State
Line Status
LOS,TX RAI
LOS,TX RAI
LOS,TX RAI
LOS,TX RAI
Test
LCP
BCP
IPCP
1 - Enabled
2 - Enabled
3 - Enabled
4 - Enabled
Data mode
Data mode
Data mode
Data mode
1 - Disabled
2 - Enabled
3 - Disabled
4 - Disabled
DOWN
DOWN
DOWN
DOWN
DOWN DOWN
DOWN DOWN
DOWN DOWN
DOWN DOWN
Ethernet Ports
Status
1 - Up
Auxiliary Alarms
Speed
Status
1 - Cleared
2 - Cleared
3 - Cleared
4 - Cleared
Severity
N/A
N/A
100 Mbps, Full Duplex
100 Mbps, Full Duplex
Unknown
2 - Up
3 - Down
4 - Down
N/A
N/A
Unknown
Power Feed
Status
PSU
Timing Source
State
Status
Status
- Normal
Secondary - Normal
Source
Internal
Internal
A - Normal
B - Normal
A - Installed Normal
B - Installed Normal
Primary
'?' - System Help Screen
Figure 5-25. Status Screen
Table 5-21. Status Screen Fields
Option
DS1 Ports
1-4
Description
Function
State
This field displays the current state of the four DS1 Ports as either
Enabled or Disabled.
Line Status
This field displays the current line status of the four DS1 ports (12 ports
on the MX412). The possible states are as follows:
• LOS: Loss of Signal
• LOF: Loss of Frame (RX Red Alarm)
• RX AIS: Receiving Alarm Indication Signal (RX Blue Alarm)
• TX AIS: Transmitting Alarm Indication Signal (TX Blue Alarm)
• RX RAI: Receiving Remote Alarm Indicator (RX Yellow Alarm)
• TX RAI: Transmitting Remote Alarm Indicator (TX Yellow Alarm)
• Normal: Indicates no alarms currently active
5-40 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Table 5-21. Status Screen Fields (Continued)
Option
Description
Function
Test
This field displays one of the following possible states:
• Data Mode: Indicates no tests are active
• Payload Loopback: Indicates that a payload loopback is in progress
• Line Loopback: Indicates that a line loopback is in progress
PPP Interfaces
1-4 State
This field displays the current state of the four PPP interfaces as either
Enabled or Disabled.
LCP
BCP
IPCP
This field displays the active state of this control protocol as either Up or
Down.
This field Displays the active state of this control protocol as either Up or
Down.
This field Displays the active state of this control protocol as either Up or
Down.
Ethernet Ports
1-4 Status
Speed
This field displays the current status as either Up or Down.
This field Displays one of the following speeds as active:
• 10 Mbps, Half Duplex
• 10 Mbps, Full Duplex
• 100 Mbps, Half Duplex
• 100 Mbps, Full Duplex
Auxiliary Alarms
1-4
Status
This field displays the current alarm status as either Active or Cleared.
Severity
This field displays the current alarm severity. Severities are defined by the
customer and displayed as Critical, Major, Minor, Alert, or Info.
Power Feed
A/B
Status
This field displays the power feed (which connects to the rear of the
MX410/MX412) as either Normal or Failed.
PSU (MX410 Only)
A/B
State
This field displays the current status of the A/B PSUs as either Installed
or Removed.
Status
This field displays the current status of the A/B PSUs as Normal, Failed
(if the PSU is installed), or N/A (if the PSU is not installed).
Timing Source
Primary/
Status
This field displays the status as either Normal or Failed.
Secondary
Source
This field Displays internal or DS1 (1-4 on MX410 or 1-12 on MX412).
61189500L1-1B
PRELIMINARY 5-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Test Menu
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
Test
DS1 Ports
1 - #1 : Pattern
2 - #2 : Data mode
3 - #3 : Data mode
4 - #4 : Data mode
5 - Reset ALL Tests
6 - Loopback Timeout:
120 Minutes
Selection :
'?' - System Help Screen
Figure 5-26. Test Menu
Table 5-22. Test Menu Options
Option Description
Function
DS1 Ports (1-4 on MX410 and 1-12 on MX412)
1-4
#1 - #4
43.
5
Reset ALL Tests
Loopback Timeout
This option is used to stop all DS1 port testing and resets all DS1
ports to Data Mode.
6
This option is used to set the loopback timeout value. The default
value is 120 Minutes and the possible values are as follows:
• 120 Minutes
•
•
•
•
•
•
•
90 Minutes
60 Minutes
30 Minutes
15 Minutes
10 Minutes
5 Minutes
Disabled
5-42 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
DS1 (Port #) Menu
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
DS1 1
1 - Loopback
: Pattern
: Ones
Pattern
2 - Insert One Bit Error
3 - Clear Bit Error Count
Patt Sync
Bit Errors
: NO SYNC
: 14
DS1 1 Status
: LOS,TX RAI
Selection:
'?' - System Help Screen
Figure 5-27. DS1 (Port #) Menu
Table 5-23. DS1 (Port #) Menu Options
Option Description
Function
1
Loopback
This option is used to display the current loopback. Selecting this
N/A
2
Pattern
This option is used to display the current pattern type.
Insert One Bit Error
This option is present only when a pattern has been selected and
inserts one bit error count.
3
Clear Bit Error Count This option is present only when a pattern has been selected and
clears one bit error count.
Patt Sync
This read-only field displays the pattern synchronization status.
This read-only field displays the current number of bit errors.
This read-only field displays the current status of the selected port.
Bit Errors
DS1 (#) Status
61189500L1-1B
PRELIMINARY 5-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Port (#) Test Menu
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
Port #1 : Pattern
1 - Data Mode
2 - Payload
3 - Line
4 - Inward
5 - Dual
6 - Remote FDL Line
7 - Remote Inband Line (CSU)
8 - Remote FDL Payload
9 - Pattern Test
Selection:
'?' - System Help Screen
Figure 5-28. Port (#) Test Menu
The Port (#1-#4 on MX410, and #1-#12 on MX412) Test menu options are shown in Table 5-
24.
Table 5-24. Port (#) Test Menu Options
Option Description
Function
1
2
3
4
5
6
Data Mode
Payload
This option indicates that no tests are active.
This option initiates a payload loopback test.
This option initiates a line loopback test.
This option initiates an inward loopback test.
This option initiates both line and inward loopback tests.
Line
Inward
Dual
Remote FDL Line
This option transmits a request via the FDL (Facility Data Link) for
the remote unit to issue a line loopback (ESF only).
7
8
9
Remote Inband Line
(CSU)
This option transmits an inband request for the remote unit to
issue a line loopback.
Remote FDL Payload
This option transmits a request via the FDL for the remote unit to
issue a payload loopback (ESF only).
Pattern Test
This option invokes the DS1 Test Pattern menu.
5-44 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
DS1 Test Pattern Menu
pattern data.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
DS1 1 Test Pattern
1 - QRSS
2 - All Ones
3 - All Zeros
4 - 511
5 - 2047
6 - 2^15-1
7 - 2^20-1
Selection :
'?' - System Help Screen
Figure 5-29. DS1 Test Pattern Menu
The DS1 Test Pattern menu options are all test pattern types. Selecting any of the options
invokes a warning menu that test patterns are service affecting and requests execution
verification.
Pattern type options are as follows:
• QRSS
• All Ones
• All Zeros
• 511
• 2047
• 2^15-1
• 2^20-1
61189500L1-1B
PRELIMINARY 5-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Performance Monitoring Menu
data affecting the MX410/MX412 operations. Data is viewed in daily or 15-minute
increments.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
Performance Monitoring
1 - Daily PM Table
2 - Quarter Hour PM Table
3 - Daily PM Thresholds
4 - Quarter Hour PM Thresholds
5 - Clear PM Data
Selection :
'?' - System Help Screen
Figure 5-30. Performance Monitoring Menu
Table 5-25. Port (#) Test Menu Options
Option Description
Function
1
2
3
4
5
Daily PM Table
This option invokes the “Daily Performance Monitoring
Quarter Hour PM Table
Daily PM Thresholds
This option invokes the “Quarter Hour Performance
Clear PM Data
5-46 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Table 5-26. Performance Monitoring Definitions
T1 PM Parameter Definition
Description
CV-L
Code Violation - Line
This parameter indicates the number of Bipolar Viola-
tions (BPVs) and Excessive Zeros (EXZs) that have
occurred during the accumulation period.
ES-L
Errored Seconds - Line
This parameter indicates the number of seconds for
which one or more Line Coding Violations (CV-Ls), or
one or more Loss of Signal (LOS) defects occurred.
SES-L
LOSS-L
CV-P
Severely Errored Seconds - Line
Loss of Signal Second - Line
Code Violation - Path
This parameter indicates the number of seconds with
1544 or more CV-Ls or one or more LOS defects.
This parameter indicates the number of seconds for
which one or more LOS defects occurred.
SF Mode: This parameter indicates the number of
frame synchronization bit errors that have occurred
during the accumulation period.
ESF Mode: This parameter indicates the number of
CRC-6 errors that have occurred during the accumula-
tion period.
ES-P
Errored Seconds - Path
SF Mode: This parameter indicates the number of
seconds containing any of the following:
1
•
•
•
•
FE errors
CS events
2
3
SEF defects
4
AIS defects
ESF Mode: This parameter indicates the number of
seconds containing any of the following:
5
•
•
•
•
CRC-6 errors
CS events
SEF defects
AIS defects
SES-P
SAS-P
Severely Errored Seconds - Path
SF Mode: This parameter indicates the number of
seconds with 8 or more FE events or one or more SEF
or AIS defects.
ESF Mode: This parameter indicates the number of
seconds with 320 or more CRC-6 errors or one or more
SEF or AIS defects.
Severely Errored Frame/AIS
Second - Path
This parameter indicates the number of seconds
containing one or more SEF defects or one or more AIS
defects.
UAS-P
CSS-P
Unavailable Second - Path
This parameter indicates the number of seconds for
which the DS1 path contains 10 contiguous SESs.
Controlled Slip Second - Path
This parameter indicates the number of seconds
containing one or more controlled frame slips.
1. FE (Frame bit Error): This parameter indicates the occurrence of a frame bit error in the received frame bit pattern.
2. CS (Controlled Slip): This parameter indicates the replication or deletion of the 192 payload bits of a DS1 frame by
the receiving unit.
3. SEF (Severely Errored Frame): This parameter indicates that two or more frame bit errors are detected in a window.
4. AIS (Alarm Indication Signal): This parameter indicates the detection of an unframed signal with a 1s density of at
least 99.9% for a time.
5. CRC-6 (Cyclic Redundancy Check) error - used in ESF mode only: This parameter indicates the existence of a
CRC-6 code that is not identical to the corresponding locally calculated code.
61189500L1-1B
PRELIMINARY 5-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Daily Performance Monitoring Screen
monitoring data in daily increments and in a tabular format.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
DS1 Port 1 Daily Performance Monitoring
Current
0
52549
Total
0
134621
06/22
0
86374
06/21
0
48247
N/A
0
N/A
0
N/A
0
N/A
0
CV-L
ES-L
0
0
0
0
SES-L
LOSS-L
CV-P
52549
52549
134621
134621
86374
86374
48247
48247
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ES-P
0
0
0
0
0
0
0
0
SES-P
SAS-P
UAS-P
CSS-P
0
0
0
0
0
0
0
0
0
52549
0
0
134621
0
0
86374
0
0
48247
0
0
0
0
0
0
0
0
0
0
0
0
0
(N)Next DS1, (P)Prev DS1, (E)Enter DS1, (F)Forward, (B)Back, Selection:
Figure 5-31. Daily Performance Monitoring Screen
Quarter Hour Performance Monitoring Screen
performance monitoring data in 15-minute increments and in a tabular format.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
DS1 Port 1 Quarter Hour Performance Monitoring
Current
Total
0
86366
15:15
0
15:00
0
14:45
0
14:30
0
14:15
0
14:00
0
CV-L
ES-L
0
556
556
556
0
899
899
899
0
900
900
900
0
900
900
900
0
899
899
899
0
900
900
900
0
900
900
900
0
SES-L
LOSS-L
CV-P
86366
86366
0
ES-P
0
0
0
0
0
0
0
0
SES-P
SAS-P
UAS-P
CSS-P
0
0
0
0
0
0
0
0
0
0
86366
0
0
0
0
0
0
0
556
0
899
0
900
0
900
0
899
0
900
0
900
0
(N)Next DS1, (P)Prev DS1, (E)Enter DS1, (F)Forward, (B)Back, Selection:
Figure 5-32. Quarter Hour Performance Monitoring Screen
5-48 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Daily PM Thresholds Menu
thresholds data in a tabular format. This menu is used to set the performance monitoring
threshold levels and enable or disable an alarms if the threshold is exceeded.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
Daily PM Thresholds
Threshold
Alarm
1 - ES-L
:
648
132960
691
648
100
17
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
2 - CV-P (ESF mode) :
3 - CV-P (SF mode) :
4 - ES-P
5 - SES-P
6 - SAS-P
7 - CSS-P
8 - UAS-P
:
:
:
:
:
4
10
9 - Restore ALL DS1 Threshold Defaults
10 - Enable ALL DS1 Threshold Alarms
11 - Disable ALL DS1 Threshold Alarms
Selection :
'?' - System Help Screen
Figure 5-33. Daily PM Thresholds Menu
Table 5-27. Daily PM Thresholds Menu Options
Option Description
Function
1
ES-L
This option sets the ES-L threshold value. The available
threshold range is (1-65535). The default value is 648.
2
CV-P (ESF mode)
This option sets the CV-P ESF threshold value. The available
threshold range is (1-1048575). The default value is
132,960.
3
4
5
6
7
CV-P (SF mode)
ES-P
This option sets the CV-P SF threshold value. The available
threshold range is (1-1048575). The default value is 691.
This option sets the ES-P threshold value. The available
threshold range is (1-65535). The default value is 648.
SES-P
This option sets the SES-P threshold value. The available
threshold range is (1-65535). The default value is 100.
SAS-P
This option sets the SAS-P threshold value. The available
threshold range is (1-65535). The default value is 17.
CSS-P
This option sets the CSS-P threshold value. The available
threshold range is (1-65535). The default value is 691.
61189500L1-1B
PRELIMINARY 5-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Table 5-27. Daily PM Thresholds Menu Options (Continued)
Option Description
Function
8
UAS-P
This option sets the UAS-P threshold value. The available
threshold range is (1-65535). The default value is 10.
9
Restore ALL DS1 Threshold
Defaults
This option restores all threshold values to the defaults
listed above.
10
11
Enable ALL DS1 Threshold
Alarms
This option enables all daily threshold alarms.
Disable ALL DS1 Threshold
Alarms
This option disables all daily threshold alarms.
5-50 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Quarter Hour PM Thresholds Menu
monitoring thresholds data in a tabular format. This menu is used to set the performance
monitoring threshold levels and enable or disable an alarms if the threshold is exceeded.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL MAJOR
ID:
Quarter Hour PM Thresholds
Threshold
Alarm
1 - ES-L
:
65
13296
72
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
2 - CV-P (ESF mode) :
3 - CV-P (SF mode) :
4 - ES-P
5 - SES-P
6 - SAS-P
7 - CSS-P
8 - UAS-P
:
:
:
:
:
65
10
2
1
10
9 - Restore ALL DS1 Threshold Defaults
10 - Enable ALL DS1 Threshold Alarms
11 - Disable ALL DS1 Threshold Alarms
Selection :
'?' - System Help Screen
Figure 5-34. Quarter Hour PM Thresholds Menu
Table 5-28. Quarter Hour PM Thresholds Menu Options
Option Description
Function
1
2
3
4
5
6
7
ES-L
This option sets the ES-L threshold value. The available
threshold range is (1-900). The default value is 65.
CV-P (ESF mode)
CV-P (SF mode)
ES-P
This option sets the CV-P ESF threshold value. The available
threshold range is (1-16383). The default value is 13,296.
This option sets the CV-P SF threshold value. The available
threshold range is (1-16383). The default value is 72.
This option sets the ES-P threshold value. The available
threshold range is (1-900). The default value is 65.
SES-P
This option sets the SES-P threshold value. The available
threshold range is (1-900). The default value is 10.
SAS-P
This option sets the SAS-P threshold value. The available
threshold range is (1-900). The default value is 2.
CSS-P
This option sets the CSS-P threshold value. The available
threshold range is (1-900). The default value is 72.
61189500L1-1B
PRELIMINARY 5-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Table 5-28. Quarter Hour PM Thresholds Menu Options (Continued)
Option Description
Function
8
UAS-P
This option sets the UAS-P threshold value. The available
threshold range is (1-900). The default value is 10.
9
Restore ALL DS1 Threshold
Defaults
This option restores all threshold values to the defaults
listed above.
10
11
Enable ALL DS1 Threshold
Alarms
This option enables all quarter hour threshold alarms.
Disable ALL DS1 Threshold
Alarms
This option disables all quarter hour threshold alarms.
Clear PM Data Menu
This option invokes the Clear Performance Monitoring Data menu and requests verification
before deleting all previously collected performance monitoring data.
5-52 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
System Alarms Menu
MX410/MX412 system operations. Alarms may be viewed within the Master Log menu
(detailed in the next section). The Environmental Alarms menu contains provisionable
options. The Alarm Chronology menu offers the viewing of alarms in either ascending or
descending order.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
System Alarms
1 - Master Log
2 - Environmental Alarms
3 - Alarm Chronology : Ascending
Selection :
'?' - System Help Screen
Figure 5-35. System Alarms Menu
61189500L1-1B
PRELIMINARY 5-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
Master Log Menu
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
MINOR
ID:
Alarms
1 to
5 of
5
Date
Time
Type
T1
Port
Level
Description
Status
Active
Active
Active
Active
*Active
04/19/05 19:31:24
04/19/05 19:31:24
04/19/05 19:31:24
04/19/05 19:31:24
04/23/05 17:10:17
1
2
3
4
CRITICAL DS1 LOS
CRITICAL DS1 LOS
CRITICAL DS1 LOS
CRITICAL DS1 LOS
T1
T1
T1
SYSTIMING
MINOR
SRC A FAILED
------------------------------>>> END OF ALARMS <<<-----------------------------
Inverse = Active
(N)ext (P)revious (F)irst (L)ast (C)lear (A)cknowledge
* = Unacknowledged
Chronology = Ascending
Figure 5-36. Master Log Menu
Terminology and options at the bottom of the menu are explained below:
• Inverse = Active: Current active alarms are shown with reverse video text.
• * = Unacknowledged: Unacknowledged alarms are shown with an asterisk (*) in the
STATUS column.
• Chronology = Ascending: Displays the current alarm chronology setting. The alarm
chronological sequence can be set to display in ascending or descending order in the
System Alarms menu.
• (N)ext: Pressing the N key displays the next screen of alarms when all alarms cannot be
displayed on one screen.
• (P)revious: Pressing the P key displays the previous screen of alarms when all alarms
cannot be displayed on one screen.
• (F)irst: Pressing the F key displays the first alarms in the current chronological sequence.
• (L)ast: Pressing the L key displays the last alarms in the current chronological sequence.
• (C)lear: Pressing the C key clears all inactive alarms.
• (A)cknowledge: Pressing the A key acknowledges all unacknowledged alarms (which
removes asterisks from the menu).
5-54 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
MX410/MX412 System Manual
Menu Descriptions
Code Download Method Menu
software of the MX410/MX412.
MX410
MM/DD/YY HH:MM
MX410
Active Alarms: CRITICAL
ID:
Code Download Method
1 - X-MODEM
2 - TFTP
Selection :
'?' - System Help Screen
Figure 5-37. Code Download Method Menu
Table 5-29. Code Download Method Menu Options
Option Description
Function
1
X-MODEM
This option invokes another menu to initiate an X-Modem
transfer. Options are as follows:
• Initiate Transfer: This option initiates the transfer. Once
initiated use the VT100 terminal or VT100 emulation
software to send the file to the MX410/MX412.
• Card Reset: This option applies newly downloaded
software to the MX410/MX412.
2
TFTP
This option invokes another menu to initiate a TFTP
transfer. Options are as follows:
• TFTP Server: This option is used to enter the IP address
where the TFTP server resides.
• Remote Filename: This option is used to enter the
filename stored on the TFTP server.
• Initiate Transfer: This option is used to start the transfer
process.
• Card Reset: This option applies newly downloaded
software to the MX410/MX412.
61189500L1-1B
PRELIMINARY 5-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Descriptions
MX410/MX412 System Manual
This page is intentionally blank.
5-56 PRELIMINARY
61189500L1-1B
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Warranty
WARRANTY AND CUSTOMER SERVICE
ADTRAN will replace or repair this product within the warranty period if it does not meet its
published specifications or fails while in service. Warranty information can be found at
Refer to the following subsections for sales, support, Customer and Product Service (CAPS)
requests, or further information.
ADTRAN Sales
Pricing/Availability:
800-827-0807
ADTRAN Technical Support
Pre-Sales Applications/Post-Sales Technical Assistance:
800-726-8663
Standard hours: Monday - Friday, 7 a.m. - 7 p.m. CST
Emergency hours: 7 days/week, 24 hours/day
ADTRAN Repair/CAPS
Return for Repair/Upgrade:
(256) 963-8722
Repair and Return Address
Contact CAPS prior to returning equipment to ADTRAN.
ADTRAN, Inc.
CAPS Department
901 Explorer Boulevard
Huntsville, Alabama 35806-2807
61189500L1-1B
PRELIMINARY A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Carrier Networks Division
901 Explorer Blvd.
Huntsville, AL 35806
Download from Www.Somanuals.com. All Manuals Search And Download.
|