Router Option Module
1200350L1
USER MANUAL
61200350L1-1A
July 1998
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THIS MANUAL
This manual is arranged so you can quickly and easily find the in-
formation you need. The following is an overview of the contents
of this manual:
•
•
•
•
•
•
•
Chapter 1, Introduction, familiarizes you with an over view of
the Router Option Module.
Chapter 2, Installation, describes the installation of the Router
Option Module connectors.
Chapter 3, Operation, explains how to operate your Router
Option Module using the terminal interface.
Chapter 4, Configuration Overview, explains how to access
the Router Option Module configuration menu.
Chapter 5, Statistics, describes how to access statistical infor-
mation from the Router Option Module.
Chapters 6, Diagnostics, explains how to access the Router
Option Module diagnostic features.
Chapter 7, Utility Menu, explains how the Router Option
Module’s embedded utilities manage and test the network
and facilitate software upgrades.
•
•
•
•
•
Appendix A, Pinouts, provides pinouts for the Router Option
Module connectors.
Appendix B, Specifications, contains product specifications
and features.
Appendix C, Log Messages, contains messages of events that
occur.
Appendix D, SNMP, explains the simple network manage-
ment protocol and how it works.
Appendix E, Terminal Mode Commands, describes how the
Terminal Mode Commands work.
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes provide additional useful information.
Cautions signify information that could prevent service in-
terruption.
Warnings provide information that could prevent
damage to the equipment or endangerment to hu-
man life.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful in-
terference to radio frequencies. Operation of this equipment in a
residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Shielded cables must be used with this unit to ensure compliance
with Class A FCC limits.
Change or modifications to this unit not expressly
approved by the party responsible for compliance
could void the user's authority to operate the equip-
ment.
CANADIAN EMISSIONS REQUIREMENTS
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus as set out in the interfer-
ence-causing equipment standard entitled "Digital Apparatus,"
ICES-003 of the Department of Communications.
Cet appareil nuerique respecte les limites de bruits radioelec-
triques applicables aux appareils numeriques de Class A pre-
scrites dans la norme sur le materiel brouilleur: "Appareils
Numeriques," NMB-003 edictee par le ministre des Communica-
tions.
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADIAN EQUIPMENT LIMITATIONS
Notice: The Canadian Industry and Science Canada label identi-
fies certified equipment. This certification means that the equip-
ment meets certain telecommunications network protective,
operational, and safety requirements. The Department does not
guarantee the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is per-
missible to be connected to the facilities of the local telecommuni-
cations company. The equipment must also be installed using an
acceptable method of connection. In some cases, the company's
inside wiring associated with a single line individual service may
be extended by means of a certified connector assembly (tele-
phone extension cord). The customer should be aware that com-
pliance with the above conditions may not prevent degradation of
service in some situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications com-
pany cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and in-
ternal metallic water pipe system, if present, are connected to-
gether. This precaution may be particularly important in rural
areas.
Users should not attempt to make such connections them-
selves, but should contact the appropriate electric inspection
authority, or an electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes
the percentage of the total load to be connected to a telephone
loop which is used by the device, to prevent overloading. The ter-
mination on a loop may consist of any combination of devices
subject only to the requirement that the total of the Load Numbers
of all devices does not exceed 100.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1. Introduction ............................................................................. 1-1
Product Overview ......................................................................................... 1-1
Basic Functions of Router Option Module................................................. 1-1
LAN Bridge ...................................................................................... 1-1
IP Router........................................................................................... 1-1
IPX Router ........................................................................................ 1-1
Network Address Translation (NAT) .......................................... 1-2
PPP or Frame Relay ........................................................................ 1-2
Routing and Bridging with the Router
Option Module............................................................................................... 1-2
Factory Default ................................................................................ 1-2
Bridging ............................................................................................ 1-2
IP Routing......................................................................................... 1-2
IPX Routing...................................................................................... 1-3
Concurrent Routing and Bridging .............................................................. 1-3
Network Address Translation Mode (NAT) ............................................. 1-3
Warranty and Customer Service ................................................................. 1-4
Chapter 2. Installation ............................................................................... 2-1
Unpack, Inspect, Power Up.......................................................................... 2-1
Receipt Inspection ......................................................................................... 2-1
ADTRAN Shipments Include........................................................ 2-1
Installation ...................................................................................................... 2-2
Placement of the Option Module ................................................................ 2-2
Power Connection ......................................................................................... 2-3
Attaching the Plug-On Board ...................................................................... 2-3
Control............................................................................................................. 2-4
10BaseT............................................................................................................ 2-4
Chapter 3. Operation .................................................................................. 3-1
Front Panel...................................................................................................... 3-1
Terminal Menu Structure ............................................................................. 3-1
Main Menu Options........................................................................ 3-1
Configuration Menu ................................................................ 3-2
Status Menu .............................................................................. 3-3
Test Menu.................................................................................. 3-3
Logs Menu ................................................................................ 3-3
Utilities Menu ........................................................................... 3-3
Navigating the Terminal Menus ................................................................. 3-4
61200350L1-1
Router Option Module User Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
General Layout............................................................................................... 3-4
Menu Path....................................................................................................... 3-4
Moving Around ............................................................................................. 3-4
Reading Menu Options .................................................................. 3-5
Navigating the Keyboard............................................................... 3-5
Session Management ...................................................................... 3-6
Configuration................................................................................... 3-7
Security Levels ............................................................................................... 3-8
Chapter 4. Configuration Overview ....................................................... 4-1
Configuration Menu...................................................................................... 4-1
Configuration/System Info.......................................................................... 4-1
System Name............................................................................ 4-2
System Location ....................................................................... 4-2
System Contact......................................................................... 4-2
Firmware Revision................................................................... 4-2
System Uptime ......................................................................... 4-2
Date/Time................................................................................. 4-2
Configuration/WAN .................................................................................... 4-3
WAN/DSO Rate.............................................................................. 4-3
WAN/L2 Protocol (also available via Front Panel)............ 4-3
Configuration/IP........................................................................................... 4-4
IP/IP Address (also available via Front Panel) ................... 4-4
IP/Subnet Mask (also available via Front Panel)................ 4-4
IP/Default Gateway (also available via Front Panel)......... 4-4
IP/Static Routes............................................................................... 4-5
Static Routes/Active................................................................ 4-5
Static Routes/IP Address........................................................ 4-5
Static Routes/Subnet Mask .................................................... 4-5
Static Routes/Gateway ........................................................... 4-5
Static Routes/Hops.................................................................. 4-5
Static Routes/Private............................................................... 4-5
IP/IP Router ................................................................................................... 4-6
IP Router/Mode .............................................................................. 4-6
IP/RIP ............................................................................................... 4-6
RIP/Mode ................................................................................. 4-6
RIP/Protocol............................................................................. 4-6
RIP/Method.............................................................................. 4-6
RIP/Direction ........................................................................... 4-6
RIP/V2 Secret ........................................................................... 4-7
IP/NAT ..................................................................................... 4-7
NAT/DHCP Mode .................................................................. 4-7
NAT/DHCP Renewal Time ................................................... 4-7
viii
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
NAT/Web Server ..................................................................... 4-7
NAT/Default IP........................................................................ 4-7
IP/DNS.............................................................................................. 4-8
DNS/Domain Name ................................................................ 4-8
DNS/Server 1............................................................................ 4-8
DNS/Server 2............................................................................ 4-8
IP/UDP Relay................................................................................................. 4-8
UDP Relay/Mode............................................................................ 4-8
UDP Relay/UDP Relay List........................................................... 4-9
UDP Relay List/Relay Address.............................................. 4-9
UDP Relay List/UDP Port Type ............................................ 4-9
UDP Relay List/UDP Port 1, UDP Port 2, UDP Port 3 ....... 4-9
IP/Proxy ARP ........................................................................... 4-9
Configuration/IPX....................................................................................... 4-10
IPX/Mode................................................................................ 4-10
IPX/Network .......................................................................... 4-10
IPX/Frame Type..................................................................... 4-11
IPX/Seed Status...................................................................... 4-11
IPX/RIP Timer ........................................................................ 4-12
IPX/SAP Timer....................................................................... 4-12
Configuration/Bridge ................................................................................. 4-13
Bridge/Mode.................................................................................. 4-13
Bridge/WAN IP Bridge ................................................................ 4-14
WAN IP Bridge/Network..................................................... 4-14
WAN IP Bridge/Netmask..................................................... 4-14
WAN IP Bridge/Triggered ................................................... 4-14
WAN IP Bridge/Proxy ARP ................................................. 4-14
Bridge/WAN IPX Bridge ............................................................. 4-14
WAN IPX Bridge/Network .................................................. 4-15
WAN IPX Bridge/Frame Type............................................. 4-15
WAN IPX Bridge/Seed Status.............................................. 4-15
WAN IPX Bridge/Triggered................................................. 4-15
Bridge/Spanning Tree .................................................................. 4-15
Spanning Tree/Mode............................................................. 4-15
Spanning Tree/Priority ......................................................... 4-16
Spanning Tree/Maximum Age ............................................ 4-16
Spanning Tree/Hello Time ................................................... 4-16
Spanning Tree/Forward Delay ............................................ 4-16
Spanning Tree/LAN Port...................................................... 4-16
LAN Port/Active.................................................................... 4-16
LAN Port/Path Cost .............................................................. 4-16
LAN Port/Priority.................................................................. 4-17
61200350L1-1
Router Option Module User Manual
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Spanning Tree/Bridge Group 1 .................................................. 4-17
Bridge Group 1/Active ......................................................... 4-17
Bridge Group 1/Path Cost.................................................... 4-17
Bridge Group 1/Priority ....................................................... 4-17
Spanning Tree/Bridge Group 2 .................................................. 4-17
Bridge Group 2/Active ......................................................... 4-17
Bridge Group 2/Path Cost.................................................... 4-17
Bridge Group 1/Priority ....................................................... 4-17
Bridge/Address Table.................................................................. 4-18
Address Table/Aging ........................................................... 4-18
Address Table/Forward Policy ........................................... 4-18
Configuration/Security .............................................................................. 4-19
Security/Authentication....................................................... 4-19
Security/Radius Server................................................................ 4-19
Radius Server/Primary Server ............................................ 4-20
Radius Server/Secondary Server ........................................ 4-20
Radius Server/UDP Port ...................................................... 4-20
Radius Server/Secret............................................................. 4-20
Radius Server/Retry Count.................................................. 4-20
Security/PPP.................................................................................. 4-21
Security/Filter Defines................................................................. 4-22
Filter Defines/MAC Filter Defines...................................... 4-22
Filter Defines /Pattern Filter Defines.................................. 4-23
Filter Defines/IP Filter Defines............................................ 4-23
Filter Defines /IPX Filter Defines........................................ 4-24
Frame Relay ............................................................................ 4-26
Frame Relay/Maintenance Protocol ................................... 4-27
Frame Relay/Polling Frequency.......................................... 4-27
Frame Relay/DLCI Mapping............................................... 4-27
DLCI Mapping/Active ......................................................... 4-29
DLCI Mapping/DLCI ........................................................... 4-29
DLCI Mapping/IP Map ........................................................ 4-29
IP Map/Active........................................................................ 4-29
IP Map/IARP.......................................................................... 4-29
IP Map/Far-End IP Address ................................................ 4-29
IP Map/IP Netmask .............................................................. 4-29
IP Map/Link IP Address ...................................................... 4-30
IP Map/RIP Protocol............................................................. 4-30
IP Map/RIP Method.............................................................. 4-30
IP Map/RIP Direction ........................................................... 4-31
DLCI Mapping/IPX Map ..................................................... 4-31
IPX Map/Active..................................................................... 4-31
x
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
IPX Map/IARP ....................................................................... 4-31
IPX Map/Link Network ........................................................ 4-31
DLCI Mapping/Bridge Map................................................. 4-32
Bridge Map/Active ................................................................ 4-32
Bridge Map/Bridge Group ................................................... 4-32
DLCI Mapping/Filters........................................................... 4-32
Configuration/PPP Profile ......................................................................... 4-35
PPP Profile/Authentication ......................................................... 4-35
Authentication/Tx Method................................................... 4-36
Authentication/Tx Username .............................................. 4-36
Authentication/Tx Password ............................................... 4-36
Authentication/Rx Username .............................................. 4-36
Authentication/Rx Password............................................... 4-36
PPP Profile/IP ................................................................................ 4-36
IP/Mode................................................................................... 4-37
IP/NAT.................................................................................... 4-37
IP/Route .................................................................................. 4-37
Route/IP/Net ......................................................................... 4-37
Route/Netmask ...................................................................... 4-37
Route/Force IP........................................................................ 4-37
IP/RIP.............................................................................................. 4-38
RIP/Mode................................................................................ 4-38
RIP/Protocol ........................................................................... 4-38
RIP/Method ............................................................................ 4-38
RIP/Direction.......................................................................... 4-38
RIP/Triggered......................................................................... 4-39
PPP Profile/IPX ............................................................................. 4-39
IPX/Mode................................................................................ 4-39
IPX/Remote Network............................................................ 4-39
IPX/Triggered......................................................................... 4-39
IPX/Type 20 Packets.............................................................. 4-39
PPP Profile/Bridge ........................................................................ 4-40
Bridge/Mode........................................................................... 4-40
PPP Profile/PPP............................................................................. 4-40
PPP/VJ Compression............................................................. 4-40
PPP/Max Config .................................................................... 4-41
PPP/Max Timer...................................................................... 4-41
PPP/Max Failure .................................................................... 4-41
PPP Profile/Filters......................................................................... 4-41
Filters/WAN-to-LAN (In)..................................................... 4-41
Filters/In Exceptions.............................................................. 4-42
Filters/LAN-to-WAN (Out).................................................. 4-43
61200350L1-1
Router Option Module User Manual
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Filters/Out Exceptions.......................................................... 4-43
Configuration/Management ..................................................................... 4-44
Management/Telnet..................................................................... 4-44
Telnet/Server Access............................................................. 4-44
Telnet/User List ..................................................................... 4-44
User List/Name ..................................................................... 4-45
User List/Authen Method.................................................... 4-45
User List/Password............................................................... 4-45
User List/Idle Time ............................................................... 4-45
User List/Level ...................................................................... 4-45
Management/SNMP .................................................................... 4-45
SNMP Access.......................................................................... 4-46
SNMP/Communities ............................................................ 4-46
Communities/Name ............................................................. 4-46
Communities/Privilege ........................................................ 4-46
Communities/Manager IP ................................................... 4-46
SNMP/Traps .......................................................................... 4-46
Traps/Manager Name .......................................................... 4-46
Traps/Manager IP ................................................................. 4-46
Management/Maint Port............................................................. 4-47
Maint Port/Password Protect .............................................. 4-47
Maint Port/Password............................................................ 4-47
Maint Port/Baud Rate........................................................... 4-47
Maint Port/Data Bits............................................................. 4-47
Maint Port/Parity .................................................................. 4-47
Maint Port/Stop Bits ............................................................. 4-48
Configuration/Terminal Mode ................................................................. 4-48
Chapter 5. Statistics .................................................................................... 5-1
Status Menu.................................................................................................... 5-1
Status/Sessions .............................................................................................. 5-2
Sessions/PPP Session ..................................................................... 5-2
Sessions/DLCI Table ...................................................................... 5-3
Sessions/Spanning Tree................................................................. 5-4
Status/ARP Cache......................................................................................... 5-4
Status/Bridge Table ...................................................................................... 5-5
Status/IP Routes............................................................................................ 5-5
Status/IPX Routes ......................................................................................... 5-7
Status/IPX Servers ........................................................................................ 5-8
Status/WAN Stats......................................................................................... 5-8
Status/LAN Stats........................................................................................... 5-9
Status/IP Stats.............................................................................................. 5-10
Viewing Statistical Information
xii
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
(Front Panel Interface) ................................................................................. 5-11
Router Statistics Available on Front Panel ............................................... 5-11
Status .............................................................................................. 5-11
Chapter 6. Diagnostics ...............................................................................6-1
Test Menu........................................................................................................ 6-1
Test Menu/Echo Request.............................................................................. 6-1
Logs Menu....................................................................................................... 6-2
Logs/Syslog Host........................................................................................... 6-3
Logs/PPP Log................................................................................................. 6-3
PPP Log/Active ............................................................................... 6-3
PPP Log/Wrap................................................................................. 6-3
PPP Log/Level................................................................................. 6-3
PPP Log/View ................................................................................. 6-3
PPP Log/Clear ................................................................................. 6-3
Logs/Connection Log.................................................................................... 6-4
Connection Log/Active .................................................................. 6-4
Connection Log/Wrap.................................................................... 6-4
Connection Log/Level .................................................................... 6-4
Connection Log/View .................................................................... 6-4
Connection Log/Clear .................................................................... 6-4
Logs/Network Log........................................................................................ 6-4
Network Log/Active....................................................................... 6-4
Network Log/Wrap ........................................................................ 6-5
Network Log/Level ........................................................................ 6-5
Network Log/View......................................................................... 6-5
Network Log/Clear......................................................................... 6-5
Chapter 7. Utility Menu .............................................................................7-1
Terminal Mode ............................................................................................... 7-1
Utilities Menu ................................................................................................. 7-1
Utilities/Ping .................................................................................................. 7-2
Utilities/Telnet Client ................................................................................... 7-2
Utilities/Upgrade Menu ............................................................................... 7-2
Upgrade/Transfer Method ............................................................ 7-3
Upgrade/TFTP Host ....................................................................... 7-3
Upgrade/Filename.......................................................................... 7-3
Upgrade/Status ............................................................................... 7-3
Upgrade/Start Transfer.................................................................. 7-3
Upgrade/Abort Transfer................................................................ 7-4
Upgrade/TFTP Server .................................................................... 7-4
Utilities/Exit ................................................................................................... 7-4
Front Panel ...................................................................................................... 7-4
Software Revision ............................................................................ 7-4
61200350L1-1
Router Option Module User Manual
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
CMD Mode....................................................................................... 7-4
Appendix A. Pinouts .............................................................................. . A-1
Appendix B. Specifications .................................................................... B-1
Ethernet Interface (LAN) ........................................................ B-1
Display....................................................................................... B-1
Environmental.......................................................................... B-1
Physical...................................................................................... B-1
Power ......................................................................................... B-1
Agency Approvals ................................................................... B-1
Appendix C. Log Messages ................................................................... . C-1
PPP Log Messages ........................................................................................ C-1
Call Log Messages ........................................................................................ C-5
Network Log Messages ............................................................................... C-6
Appendix D. SNMP ................................................................................ D-1
Understanding SNMP.................................................................................. D-1
SNMP Components:..................................................................................... D-1
Network Manager.......................................................................... D-1
Agent................................................................................................ D-1
MIB ................................................................................................... D-2
SNMP Embedded Agent ............................................................................. D-3
Communities................................................................................... D-3
Traps................................................................................................. D-3
Appendix E. Terminal Mode Commands ............................................ E-1
Menu Commands .......................................................................................... E-1
Key Words ...................................................................................................... E-2
Additional Commands ................................................................................. E-3
Download/Uploading Configuration........................................................ E-3
Index....................................................................................................... Index-1
xiv
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
Figure 2-1. Installing the Option Module .................................................. 2-2
Figure 2-2. Attaching the Plug-On Board ................................................. 2-3
Figure 2-3. Router Option Module Rear Panel ......................................... 2-4
Figure 3-1. Top Level Terminal Menu ....................................................... 3-2
Figure 3-2. Router Option Module Front Panel Menu Structure .......... 3-9
Figure 4-1. Configuration/System Info Screen ........................................ 4-1
Figure 4-2. Configuration/Frame Relay Screen ....................................... 4-3
Figure 4-3. Configuration/IP Screen ......................................................... 4-4
Figure 4-4. Configuration/IPX Screen ..................................................... 4-10
Figure 4-5. Configuration/Bridge Screen ............................................... 4-13
Figure 4-6. Configuration/Security Screen ............................................. 4-19
Figure 4-7. Configuration/PPP Profile Screen ....................................... 4-35
Figure 4-8. Configuration/Management Screen .................................... 4-44
Figure 5-1. Status Screen .............................................................................. 5-1
Figure 6-1. Test Screen ................................................................................. 6-1
Figure 6-2. Logs Screen ................................................................................ 6-2
Figure 7-1. Utilities Screen ........................................................................... 7-1
Figure 7-2. System Statistics Screen ........................................................... 7-4
61200350L1-1
Router Option Module User Manual
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
xvi
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Tables
Table A-1: Pin Assignments for Control Connector ............................... A-1
Table A-2: 10BaseT Ethernet ...................................................................... A-1
61200350L1-1
Router Option Module User Manual
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Tables
xviii
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Chapter 1
PRODUCT OVERVIEW
The ADTRAN Router Option Module installs in the option slot of
the TSU muliplexer family of products and provides integrated rout-
ing capability access frame relay or point-to-point networks.
Basic Functions of Router Option Module
The Router Option Module provides the following basic functions:
LAN Bridge
Bridging provides a point-to-point connection between two local
area networks (LANs). The bridge learning function scans the
source and destination media access control (MAC) addresses of all
packets on its LAN and determines which packets should be trans-
mitted over the T1 link. Applications include connectivity between
single users or small offices to corporate LANs. The Router Option
Module uses the Spanning Tree Algorithm (IEEE 802.1d-ISO/
IEC10038), which provides a loop-free topology and redundancy.
IP Router
The Router Option Module can function as an IP router using the
Routing Information Protocol (RIP) for advertising and learning
routes among other routers. Static routes may also be entered into
the routing table.
IPX Router
IPX routers and services can be exchanged between the Router Op-
tion Module and other devices using RIP and Service Advertising
Protocol (SAP). Watch dog serialization filtering and spoofing can
permit the ISDN to be idle during no application traffic periods.
61200350L1-1
Router Option Module User Manual
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Network Address Translation (NAT)
Single networks can connect to the Internet with this function. The
Router Option Module translates outgoing IP packets over the T1 to
the IP router at the Internet Service Provider. Popular Internet ap-
plications are supported.
PPP or Frame Relay
The layer 2 protocol used to transfer packets can be PPP or Frame
Relay (RFC 1490). PPP allows a point-to-point connection, whereas
Frame Relay can provide up to ten permanent virtual circuits.
Routing and Bridging with the Router
Option Module
The Router Option Module is a Router and Transparent Learning
Bridge. Its features can be easily configured and used, once several
basic concepts are understood.
Factory Default
The Router Option Module comes from the factory configured for
MAC Bridging, IP routing, and IPX routing with no filters or con-
nection information defined. An IP address of 10.0.0.1 with a net-
work mask of 255.255.255.0 is preloaded. The factory default layer 2
configuration is PPP, which provides the least amount of reconfigu-
ration due to its negotiation-oriented nature.
Bridging
In Bridge Mode, the Router Option Module can be used to connect
two LAN segments. In this mode, all protocols are supported be-
cause they are transported across the T1 link at the MAC layer. The
Spanning Tree Algorithm can be used to guarantee a loop-free to-
pology. MAC- save addresses are “learned” by each Router Option
Module to prevent non-WAN packets from being bridged.
IP Routing
The Router Option Module operates as an IP router when the Con-
figuration/IP/IP Router/Mode option is configured to On. In PPP
mode, the Router Option Module uses an IP unnumbered WAN in-
1-2
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
terface. The IP address and mask assigned to the unit’s LAN inter-
face apply to all routing and IP operations for the unit.
In Frame Relay mode, each PVC can be specified as numbered or
unnumbered links. If a default gateway is specified on the network
of the Ethernet interface, the unit attempts to reach the gateway
through that interface. If no default gateway is specified (i.e.,
0.0.0.0.), the WAN interface becomes the default gateway (recom-
mended for remote applications when there are no other routers on
the remote LAN).
IPX Routing
Network routes and services are learned and advertised using No-
vell’s RIP and SAP.
Concurrent Routing and Bridging
The Router Option Module can route IP and IPX as well as bridge
nonIP/IPX packets simultaneously. The PPP profile will, by default,
negotiate PPP network protocols to support the transmission and
reception of IP, IPX, and Bridge packets. If the PPP peer does not ac-
cept a protocol, the Router Option Module will fall back to any com-
bination of routing and bridging.
Network Address Translation Mode (NAT)
NAT is a special mode of operation in which the Router Option
Module obtains a dynamically assigned IP address from the peer
router (typically an Internet Service Provider). This allows a net-
work of computers to appear as a single IP address.
NAT is enabled if the layer 2 protocol is PPP and the PPP profile has
the IP parameter NAT set to Yes, or the layer 2 protocol is Frame Re-
lay and a DLCI mapping has the IP MAP/NAT parameter set to
Yes.
The network computer’s IP stack may use DHCP to request an IP
address, default gateway address, and domain name server ad-
dresses from the Router Option Module.
61200350L1-1
Router Option Module User Manual
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Warranty and Customer Service
ADTRAN will replace or repair this product within five years from
the date of shipment if it does not meet its published specifications
or fails while in service. For detailed warranty, repair, and return
information refer to the ADTRAN Equipment Warranty and Repair
and Return Policy Procedure.
Return Material Authorization (RMA) is required prior to returning
equipment to ADTRAN.
For service, RMA requests, or further information, contact one of the
numbers listed on the inside back cover of this manual.
1-4
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Chapter 2
UNPACK, INSPECT, POWER UP
Receipt Inspection
Carefully inspect the option module for any shipping damage. If
damage is suspected, file a claim immediately with the carrier and
contact ADTRAN Customer and Product Service (CAPS). If possi-
ble, keep the original shipping container for use in shipping the
Router Option Module for repair or for verification of damage dur-
ing shipment.
ADTRAN Shipments Include
The following items are included in ADTRAN shipments of the
Router Option Module:
• Router option module
• The user manual
• A modular 8-position to 8-position cable for 10-BaseT port
• An 8-position modular to 8-position modular cable and a modu-
lar to female DB-25 adapter for access to the Control Port.
The ADTRAN Router Option Module MIB is available from ADTRAN in
the support section of the ADTRAN Web page at www.adtran.com.
61200350L1-1
Router Option Module User Manual
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
INSTALLATION
Placement of the Option Module
Figure 2-1 shows the proper placement of the option module. Per-
form the following steps to install the option module.
1. Remove the cover plate from the TSU/TDU unit rear panel.
2. Slide the option module into the rear panel of the TSU/TDU unit
until it is positioned firmly against the front of the unit.
3. Fasten the thumbscrews at both edges of the option module.
Cover Plate
TSU/HSU
UNIT
Option Module
Installing the Option Module
Figure 2-1.
2-2
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Power Connection
Each option module derives power from the base TSU/TDU unit.
Power to the TSU/TDU is supplied by a captive eight-foot power
cord.
Attaching the Plug-On Board
Figure 2-2 shows the proper attachment of a plug-on board to the op-
tion module. Perform the following steps to install the plug-on
board:
1. Hold the plug-on board above the option module.
2. Using a downward and right-to-left motion, slip the V.35 Con-
nector plug into opening in the option module back panel.
3. Moving the plug-on board downward, secure the connection of
the header pins at the front of the boards.
4. Install the two 4-40 screws at both edges of the option module.
R
OUTER
X.1
CONTR
OL
10 BASE
T
NX 56/64
PORT X.1
V.35
Attaching the Plug-On Board
Figure 2-2.
The connection of the header pins between the option module
and the plug-on board must be visually verified. Severe dam-
age of the equipment can result from an improper connection.
61200350L1-1
Router Option Module User Manual
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
R
OUTER
X.1
POR
T X.2
CONTR
OL
10 BASE
T
HO
T
REPLA
CEABLE
Router Option Module Rear Panel
Figure 2-3.
Control
The Router Option Module has an 8-pin modular jack labeled CON-
TROL. The control port provides connection to a VT 100 EIA-232
compatible interface. An 8-foot cable with adapter connector pro-
vides a standard DB-25 EIA-232 interface. See Appendix A: Pinouts
for the control port’s pin assignments. A description of the opera-
tion of this port is covered in Chapter 3: Operation.
10BaseT
The 10BaseT Port allows connection to a Local Area Network
(LAN). The 8-pin modular cable included with the Router Module
can be used to connect the 10BaseT port to an Ethernet AVB.
2-4
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Chapter 3
FRONT PANEL
Refer to the TSU Product Manual for a description of front panel op-
eration.
Terminal Menu Structure
The Router Option Module uses a multilevel menu structure con-
taining both menu items and data fields. All menu operations and
data display in the terminal menu window. The Router Option Mod-
ule is shipped in the Factory Default configuration. Connect any VT
100 or VT 220 type terminal emulator to the Maintenance port. The
default rate is 9600 baud 8-N-1. The terminal emulator can flow off
the Router Option Module using software flow control. Hardware
flow control is not used.
The opening menu (the Main menu, or top-level menu) is the access
point to all other operations. Each Main menu item has several func-
tions and submenus to identify and access specific parameters.
Figure 3-1 on page 3-2 shows the top-level terminal menu.
In order to edit items in the terminal menus, you must have the appropriate
security level. Each menu description in this section indicates the required
security level required for write access. The maintenance port is always at
security level 0, giving full access to all configuration items.
Main Menu Options
The Main menu contains the following options.
61200350L1-1
Router Option Module User Manual
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Operation
Configuration Menu
The Configuration menu provides options to set up the operational
configuration for the Router Option Module. See Chapter 4, Configu-
ration Overview, for detailed information on the available options.
1
2
8
7
3
6
5
4
1. Menu Path
2. Right Pane
Describes the current position in the terminal menu
structure.
Lists available submenus. Additional submenus
available through this pane are indicated by the [+]
and [DATA] symbols.
3. System Time
Displays the current time.
4. Navigation Help Displays list of characters you can use to navigate the
terminal menus. Press Control-Z
5. Rate Status
6. Loop Status
7. Mode
Displays current rate of connection.
Displays current status of T1.
Describes current operating mode.
Lists available menus.
8. Left Pane
Top Level Terminal Menu
Figure 3-1.
3-2
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Operation
Status Menu
The Status menu provides options to review and monitor the status
of the Router Option Module system. See Status Menu on page 5-1
for detailed information on the available options.
Test Menu
The Test menu can be used for performing diagnostic testing of the
Router Option Module. See Test Menu on page 6-1 for detailed infor-
mation on the tests available.
Logs Menu
The Logs menu can be used for viewing the operational logs for the
Router Option Module. See the Logs Menu on page 6-2 for detailed
information on the available options.
Utilities Menu
The Utilities menu provides tools for system diagnostics and up-
grading the Router Option Module. See Utilities Menu on
page 7-1 for detailed information on the available options.
61200350L1-1
Router Option Module User Manual
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Operation
NAVIGATING THE TERMINAL MENUS
The following sections provide information on how to navigate
through the terminal menus.
General Layout
When you first start a terminal mode session, the Top Level Terminal
Menu screen displays, as shown in Figure 3-1 on page 3-2. The screen
is divided into left and right panes. The left pane shows the current
list of submenus, while the right pane shows the contents of a select-
ed submenu.
Menu Path
The top line of the display shows this session’s current position
(path) in the menu tree. Figure 3-1 on page 3-2 shows the top menu
level with the cursor on the Configuration submenu, so the path dis-
play shows Router/Configuration.
Moving Around
Use the following keys to navigate the menu:
If you want to...
Press...
Move the cursor from the left pane
to the right pane.
Tab Key or
Right Arrow Key
Move the cursor from the right
pane back to the left pane.
Tab Key or
Left Arrow Key
Move around within each pane.
Activate a menu.
Up and Down Arrows
Enter Key
Travel back up the menu.
Left Arrow Key or
Escape Key
3-4
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Operation
Reading Menu Options
The following options display throughout the menus.
Menu Option
Description
Submenus [+] or [DATA]
Menus that display [+] or [DATA]
indicate that more items are available
when selected.
Activation Field <+>
Menus that display <+> indicate that
an action is to be taken, such as acti-
vating a test.
Editable Data Field
Read-Only Field
A highlighted menu item indicates
that you can enter data in that field.
An underlined field is a display field
that contains read-only information.
Navigating the Keyboard
You can use different keystrokes to navigate through the terminal
menu.
If you want to...
Press...
Activate a pop-up screen with the avail-
able keystrokes.
Control-Z
Return to the home screen.
Jump between two menu items.
Example:
H
J
Press J while on a menu item of interest, and you will jump
back to the main screen. Go to another menu item of interest,
Press J, and you will jump back to the screen that was dis-
played the first time you pressed J. Press J anytime you want
to jump between these items.
Select items.
Arrow Keys
Arrow Keys
Move between the left and right panes.
61200350L1-1
Router Option Module User Manual
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Operation
If you want to...
Press...
Travel back up the menu.
Activate an item.
Left Arrow Key
Enter
Move into a submenu.
Enter
Cancel an edit.
Escape
Escape
Escape
Tab
Travel back up the menu.
Dismiss the pop-up help screens.
Move between the left and right panes.
Move to the top of a screen.
Move to the bottom of a screen.
Ascend one menu level.
A
Z
Backspace
Session Management
If you want to...
Press...
Log out of the session.
Control-L
Invalidate the password entry and return to the Control-S
login screen.
The Password prompt will display.
Refresh the screen.
Control-R
To save time, only the portion of the screen that
has changed is refreshed. This option should be
necessary only if the display picks up incorrect
characters.
3-6
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Operation
Configuration
If you want to...
Press...
Restore factory default settings.
F
This setting restores the factory defaults based on
the location of the cursor. Entire submenus can be
factory defaulted.
Copy selected items to the clipboard. (The amount
of information you can copy depends on the cursor
location when you press C.)
C
Example:
If the cursor is over an editable field, only that item is copied. If the
cursor is over the index number of a list, then all of the items in the
row of the list are copied. For example, if the cursor is over the
Numb field in the Frame Relay Mapping screen, all of the informa-
tion associated with the Map entry is copied.
Paste the item stored in the clipboard, if the infor-
mation is compatible. You must confirm all pastes
except those to a single editable field.
P
For certain types of fields, when you paste informa-
tion into the field, the value increments by 1.
For certain types of fields, when you paste informa-
tion into the field, the value decrements by 1.
Insert a new item in a list.
I
Example:
To add a new item to the Connection List, press I
while the cursor is over the index number.
Delete a list item.
D
Example:
To delete an item from the Connection List, press D
while the index number is active.
61200350L1-1
Router Option Module User Manual
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Operation
Security Levels
Each menu item on the configuration screens has an associated se-
curity level. The security level ranges from 0 (highest security level)
to 5 (lowest security level). This level determines whether a Telnet
session can access that menu item. The Telnet session is assigned a
security level set by the user. Passwords can only be accessed at se-
curity level 0. The maintenance port is always at security level 0.
The security levels are assigned as follows:
Security
Description
Level No.
0
1
2
Access all parameters including passwords
Access all parameters except passwords
Access all parameters except passwords and
authentication methods
3
Access all parameters except passwords,
authentication methods
4
5
Access only test and status menus
Access status menus only
3-8
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Operation
TX BYTE
STATUS WAN
RX BYTE
RX CRC
TX PCKTS
RX PCKTS
TX ERRORS
RX ERRORS
LAN
1) DS0 RATE
CONFIG 1) WAN
2) LAN
2) L2 PROTOCOL
1) IP ADDRESS
2) SUBNET MASK
3) DEF GATEWAY
1) RATE
3) TERMINAL
2) DATA BITS
3) PARITY
4) STOP BITS
UTIL
TEST
1) SW REVISION
2) CMD MODE
1) HOST ADDRESS
2) NUM PCKTS
1) PING UTILITY
3) START/STOP
4) VIEW RESULTS
Router Option Module Front Panel Menu Structure
Figure 3-2.
61200350L1-1
Router Option Module User Manual
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Operation
3-10
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
Chapter 4
CONFIGURATION MENU
Configuration/System Info
The System Info menu provides basic information about the unit and
displays data fields for editing information. Figure 4-1 displays the
submenus available under this menu item.
Configuration/System Info Screen
Figure 4-1.
61200350L1-1
Router Option Module User Manual
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
System Name
Write security: 3; Read security: 5
Provides a user-configurable text string for the name of the Router
Option Module. This name can help distinguish between different
installations. You can enter up to 31 alphanumeric characters in this
field, including spaces and special characters (such as an under bar).
The system name is also used for PPP authentication and IPX ser-
vice name.
System Location
Write security: 3; Read security: 5
Provides a user configurable text string for the location of the Router
Option Module. This helps to keep track of the physical location of
the unit. You can enter up to 31 alphanumeric characters in this
field, including spaces and special characters (such as an under bar).
System Contact
Write security: 3; Read security: 5
Provides a user configurable text string for the contact name. This
field can contain a name, phone number, or e-mail address of a per-
son responsible for the Router Option Module. You can enter up to
31 alphanumeric characters in this field, including spaces and spe-
cial characters (such as an under bar).
Firmware Revision
Read security: 5
Displays the current firmware revision level of the Router Option
Module. This is a read-only field.
System Uptime
Read security: 5
Displays the length of time the Router Option Module has been run-
ning since power up or reset. This is a read-only field.
Date/Time
Write security: 3; Read security: 5
Displays the current date and time as programmed in the real-time
clock. This field can be edited. Enter the time in 24-hour format
(such as 23:00:00 to represent 11:00 PM). Enter the date in mm-dd-
yyyy format.
Example: 09-30-1998
4-2
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Configuration/WAN
The WAN menu is used to set up the ISDN parameters for the Rout-
er Option Module. Figure 4-2 shows the WAN menu.
Configuration/Frame Relay Screen
Figure 4-2.
WAN/DSO Rate
WAN/L2 Protocol (also available via Front Panel)
Write security: 3, Read security: 5
This parameter specifies the layer 2 data link layer transport used.
When selected as PPP (def), the Router Option Module will negoti-
ate PPP over the T1 interface. This would be used mainly for cam-
pus wiring applications.
Parameters for controlling the PPP negotiation are in the Configu-
ration/PPP Profile menu. Frame Relay should be selected when the
Router Option Module is connected to a Frame Relay switch. The
Configuration/Frame Relay menu is used for controlling the Frame
Relay parameters.
61200350L1-1
Router Option Module User Manual
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Configuration/IP
The IP menu is used to set up the IP parameters for the Router Op-
tion Module. Any general IP-related configuration item is under
this menu. Figure 4-3 shows the IP menu.
Configuration/IP Screen
Figure 4-3.
IP/IP Address (also available via Front Panel)
Write security: 2; Read security: 5
The IP address assigned to the Router Option Module’s Ethernet
port is set here. This address must be unique within the network.
Factory default is 10.0.0.1.
IP/Subnet Mask (also available via Front Panel)
Write security: 2; Read security: 5
The IP network mask to be applied to the Router Option Module’s
Ethernet port is set here. Factory default is 255.255.255.0.
IP/Default Gateway (also available via Front Panel)
Write security: 3; Read security: 5
The default gateway is used by the Router Option Module for send-
ing IP packets whose destination address is not found in the route
table. If this address is all zeros, then the first WAN connection be-
comes the default gateway.
4-4
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
IP/Static Routes
Static Routes can be inserted under this menu.
Static Routes/Active
Write security: 4; Read security: 5
Adds this static route entry to the IP routing table when set to Yes
(def) and removes it (if it was previously added) if set to No.
Static Routes/IP Address
Write security: 4; Read security: 5
This is the IP address of the host or network address of the device
being routed to.
Static Routes/Subnet Mask
Write security: 4; Read security: 5
This mask determines the bits in the previous IP address that are
used. If this is to be a host route, it must be set to all ones
(255.255.255.255).
Static Routes/Gateway
Write security: 4; Read security: 5
This is the IP address of the router to receive the forwarded IP pack-
et.
Static Routes/Hops
Write security: 4; Read security: 5
This is the number of router hops required to get to the network or
host. Maximum distance is 15 hops.
Static Routes/Private
Write security: 4; Read security: 5
When set to No, the Router Option Module will advertise this static
route using RIP. Otherwise, setting to Yes means that the route is
kept private.
61200350L1-1
Router Option Module User Manual
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
IP/IP Router
The IP router is configured under this menu as follows.
IP Router/Mode
Write security: 3; Read security: 5
When this option is set to On (def), the Router Option Module will
advertise and listen to routes from other IP routers.
If Off, the route table is still used but only static routes are used for
routing IP packets and only the Ethernet port is used. IP packets can
be sent over the WAN, but only when bridged.
IP/RIP
Write security: 3; Read security: 5
The Routing Information Protocol (RIP) is supported by the Router
Option Module. The following parameters are required for setting
up the mode on the Ethernet port:
RIP/Mode
Write security: 3; Read security: 5
This option turns RIP On (def) or Off.
RIP/Protocol
Write security: 3; Read security: 5
Version can be V1 (def) or V2.
RIP/Method
Write security: 3; Read security: 5
• Split Horizon - Only routes not learned on the Ethernet port are
advertised
• Poison Reverse (def) - All routes are advertised, including routes
learned from the Ethernet port. These routes are poisoned.
• None - All routes are advertised, including routes learned from
the Ethernet port. No attempt is made to poison these routes.
RIP/Direction
Write security: 3; Read security: 5
• Tx and Rx (def) - RIP advertisements are transmitted and re-
ceived on the Ethernet port.
• Tx only - RIP advertisements are transmitted and not received.
• Rx only -RIP advertisements are received but not transmitted
4-6
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
RIP/V2 Secret
Write security: 0; Read security: 0
This is a text string used for authenticating advertised routes.
IP/NAT
The Network Address Translation general parameters are set up
under this menu.
NAT/DHCP Mode
Write security: 3; Read security: 5
When this option is set to On, the Router Option Module acts as a
DHCP server and will dynamically assign IP, network mask, de-
fault gateway, and DNS addresses to any device which transmits a
broadcast DHCP request. The addresses assigned are based on the
Router Option Module’s own IP address and will be within the
same network. This mode is most commonly used with the NAT
functionality. The default is Off.
NAT/DHCP Renewal Time
Write security: 3; Read security: 5
This is the number of hours that the DHCP server should allow the
device before it is required to send a new DHCP request. The default
is 15 hours. Zero (0) represents an infinite lease.
NAT/Web Server
Write security: 3; Read security: 5
This is the IP address of a web server on the Ethernet network.
When an active NAT connection is made to the Internet, any HTTP,
FTP, or SMTP server requests from the WAN are translated and sent
to this web server.
Normally, communications across NAT must be initiated from the
LAN side of the Router Option Module. Web server allows a single
machine on the NAT side to be accessed from the Internet side of
NAT. This provides outside access to a Web server, mail, or FTP
server.
NAT/Default IP
This is the IP address used by the Router Option Module for Net-
work Address translation when nothing is assigned during the PPP
negotiation when PPP mode is active or when nothing is specified
in the DLCI Mapping Link IP Address.
61200350L1-1
Router Option Module User Manual
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
IP/DNS
The Domain Name Server parameters used by the Router Option
Module are specified here. The DNS server addresses can be ex-
changed between PPP peers. When a connection occurs and IPCP is
negotiated, the Router Option Module will get the DNS server ad-
dresses from the PPP peer.
If the configured DNS server addresses (Server 1 and Server 2) are
all zeros, the addresses from the PPP peer are used. In NAT mode,
the PPP peer’s DNS addresses are always used. TheDNSaddressesset
in Server 1 and Server 2 are offered to a PPP peer, if so requested.
DNS/Domain Name
Write security: 3; Read security: 5
This is a text string used to represent the domain name used by the
Router Option Module.
DNS/Server 1
Write security: 3; Read security: 5
This is the IP address for the primary DNS device. It is the first serv-
er to which domain name requests are sent.
DNS/Server 2
Write security: 3; Read security: 5
This is the IP address for the secondary DNS device. It is used as a
back-up in case the primary address does not respond to the re-
quest.
IP/UDP Relay
The Router Option Module can be configured as a relay agent for
UDP broadcast packets. Normally, a router will not forward UDP
broadcast packets. However, many network applications use UDP
broadcasts to configure addresses, host names, and other informa-
tion. If hosts using these protocols are not on the same network seg-
ment as the servers providing the information, the client programs
will not receive a response without enabling the UDP relay agent.
UDP Relay/Mode
Write security: 3; Read security: 5
When this option is set to On (def), the Router Option Module will
act as a relay agent.
4-8
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
UDP Relay/UDP Relay List
Up to four relay destination servers can be specified in this list.
UDP Relay List/Relay Address
Write security: 3; Read security: 5
This is the IP address of the server that will receive the relay packet.
UDP Relay List/UDP Port Type
Write security: 3; Read security: 5
Standard (def)
The following standard UDP protocols are relayed when set:
• DHCP, TFTP, DNS,
• NTP (NetworkTime Protocol, port 123). NBNS (NetBIOS Name
Server, port 137), NBDG (NetBIOS Datagram, port 138),
• BootP.
Specified
• When set, the UDP port (1 to 65535) can be specified in the UDP
Port columns (up to a maximum of three per server).
UDP Relay List/UDP Port 1, UDP Port 2, UDP Port 3
Write security: 3; Read security: 5
UDP Port 1, UDP Port 2, and UDP Port 3 are used for specifying
UDP ports to be relayed. These fields only apply when UDP Port
Type is set to Specified.
IP/Proxy ARP
Write security: 4; Read security: 5
This feature allows the network portion of a group of addresses to
be shared between several physical network segments. The ARP
protocol itself provides a way for devices to create a mapping be-
tween physical (i.e., Ethernet) addresses and logical IP addresses.
Proxy ARP makes use of this mapping feature by instructing a rout-
er to answer ARP requests as a “proxy” for the IP addresses behind
one of its ports. The device which sent the ARP request will then
correctly assume that it can reach the requested IP address by send-
ing packets to the physical address that was returned to it. This tech-
nique effectively hides the fact that a network has been (further)
subnetted.
61200350L1-1
Router Option Module User Manual
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
If this option is set to Yes (def), when an ARP request is received on
the Ethernet port, the address is looked up in the IP routing table. If
the forwarding port is not on the Ethernet port and the route is not
the default route, the Router Option Module will answer the request
with its own hardware address.
If set to No, the Router Option Module will only respond to ARP re-
quests received for its own IP address.
Configuration/IPX
The IPX menu is used to set up the IPX parameters for the Router
Option Module. Any general IPX-related configuration item can be
found under this menu. Figure 4-4 shows the IPX menu.
Configuration/IPX Screen
Figure 4-4.
IPX/Mode
Write security: 2; Read security: 5
When this option is set to On (def), the Router Option Module will
route IPX. Setting it to Off will disable all IPX functionality.
IPX/Network
Write security: 2; Read security: 5
The IPX network address for the Ethernet port is set here. This is an
eight-digit hexadecimal value that uniquely identifies the network
segment of the Ethernet port. Accidental selection of an IPX net-
work which is already in use on another network segment may
4-10
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
cause hard-to-diagnose problems. IPX network numbers should be
carefully tracked.
IPX/Frame Type
Write security: 2; Read security: 5
The Router Option Module supports all four defined IPX frame
types. The possible frame types are: Ether Type II (def), Ether 802.3
(Raw), Ether 802.2, or Ether SNMP (802.2 SNMP). Only one frame
type can be used at one time.
IPX/Seed Status
Write security: 2; Read security: 5
The seed status defines what the Router Option Module is to do
with the network information on the selected frame type during
startup. There are three possible seeding selections specified:
Seeding Selection Description
Seed
The Router Option Module will listen for
an IPX network number being sent by
another router (including Novell software
routers residing on servers) on the Ethernet
segment connected to this port and use this
number if it exists. If it doesn’t discover a
number in use, the Router Option Module
will use the configured IPX network num-
ber for the Ethernet segment.
Non-Seed (def)
The Router Option Module will listen for
an IPX network number being sent by
another router (including Novell software
routers residing on servers) on the Ether-
net segment connected to this port and use
this number if it exists. If it doesn’t dis-
cover a number in use, the Router Option
Module will wait indefinitely until a num-
ber is sent by another router on the Ether-
net segment.
61200350L1-1
Router Option Module User Manual
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Seeding Selection Description
Auto-Seed
The Router Option Module will listen for
an IPX network number being sent by
another router (including Novell software
routers residing on servers) on the Ether-
net segment connected to this port and use
this number if it exists. If it doesn’t dis-
cover a number in use, the Router Option
Module will auto-generate a valid number
using its routing tables.
IPX/RIP Timer
Write security: 3; Read security: 5
This value specifies how often the Router Option Module sends out
IPX RIP packets on the network segment attached to the Ethernet
port. The RIP packets sent contain routing information about the
networks for which this Router Option Module is responsible. The
default value is 60 seconds.
IPX/SAP Timer
Write security: 3; Read security: 5
This value specifies how often the Router Option Module sends out
IPX SAP (Service Access Protocol) packets on the network segment
attached to the Ethernet port. The SAP packets sent contain infor-
mation about the services (such as servers, printers, etc.) for which
this Router Option Module is responsible. The default value is 60
seconds.
4-12
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Configuration/Bridge
The Bridge menu is used to set up the bridge parameters for the
Router Option Module. The bridging function runs at the Media Ac-
cess Control (MAC) level which allows any protocol packets that
run over Ethernet to be forwarded. Bridging can run concurrently
with the IP and IPX routing. However, when packets are bridged
across a WAN connection, the following rules apply:
• When IP routing is active, IP packets (which include ARP pack-
ets) are not bridged.
• When IPX routing is active, IPX packets are not bridged.
• The WAN IP Bridge and WAN IPX Bridge menus allow the
WAN connection to bridge packets to the Router Option Module
but get routed as soon as they arrive at the unit.
Figure 4-5 shows the Bridge menu.
Configuration/Bridge Screen
Figure 4-5.
Bridge/Mode
Write security: 2; Read security: 5
When this option is set to On (def), the Router Option Module
bridge function will be enabled. Setting it to Off will disable all
bridge functionality.
61200350L1-1
Router Option Module User Manual
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Bridge/WAN IP Bridge
When IP routing is active, the Router Option Module will allow an-
other WAN device to bridge IP packets to itself by using PPP BCP.
Normally, two IP routers would negotiate PPP IPCP to exchange IP
packets.
However, if a device can only support PPP BCP, IP packets are en-
capsulated by the device as bridge packets. The Router Option
Module can treat the WAN IP Bridge as a virtual Ethernet port con-
nected only to a WAN device which has negotiated PPP BCP. This
menu allows the IP parameters for this virtual Ethernet to be set up.
WAN IP Bridge/Network
Write security: 2; Read security: 5
This is the IP address of the virtual Ethernet port.
WAN IP Bridge/Netmask
Write security: 2; Read security: 5
This is the network mask to be applied to the virtual Ethernet port.
WAN IP Bridge/Triggered
Write security: 2; Read security: 5
When set to Yes, only IP RIP updates are sent when the routing table
has changed. When set to No (def), updates are sent periodically.
RIP version, method, and direction are determined by the Ethernet
parameters set in the Configuration/IP/IP Router/RIP menu.
WAN IP Bridge/Proxy ARP
If this option is set to Yes (def), the Router Option Module will
proxy ARP on the bridge IP port. See the section IP/Proxy ARP on
page page 4-9 for an explanation of the proxy ARP function.
Bridge/WAN IPX Bridge
When IPX routing is active, the Router Option Module will allow
another WAN device to bridge IPX packets to it using PPP BCP.
Normally, two IPX routers would negotiate PPP IPXCP to exchange
IPX packets. However, if a device can support only PPP BCP, IPX
packets are encapsulated by the device as bridge packets. The Rout-
er Option Module can treat the WAN IPX Bridge as a virtual Ether-
4-14
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
net port connected only to a WAN device which has negotiated PPP
BCP. This menu allows the IPX parameters for this virtual Ethernet
to be set up.
WAN IPX Bridge/Network
Write security: 2; Read security: 5
This is the network address of the virtual Ethernet port. See IPX/Net-
work on page page 4-10 for explanation of the IPX network number.
WAN IPX Bridge/Frame Type
Write security: 2; Read security: 5
This is the frame type used for the virtual Ethernet port. See IPX/
Frame Type on page page 4-11 for an explanation of the IPX frame
type.
WAN IPX Bridge/Seed Status
Write security: 2; Read security: 5
This is the seed status used for the virtual Ethernet port. See IPX/
Seed Status on page page 4-11 menu for an explanation of the IPX seed
status.
WAN IPX Bridge/Triggered
Write security: 2; Read security: 5
When set to Yes, only IPX RIP and SAP updates are sent when the
routing or service table has changed. When set to No (def), updates
are sent at the same rate set for the Ethernet port (see IPX/RIP Timer
and IPX/SAP Timer on page page 4-12).
Bridge/Spanning Tree
The Spanning Tree Algorithm and Protocol ensures a loop-free to-
pology and provides redundancy. The protocol parameters can be
specifically tuned from their defaults, though most applications re-
quire no adjustment.
Spanning Tree/Mode
Write security: 2; Read security: 5
When the mode is set to On, the Router Option Module will
participate in the spanning tree protocol between other bridges.
When Off (def), all bridge ports remain permanently open for for-
warding.
61200350L1-1
Router Option Module User Manual
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Spanning Tree/Priority
Write security: 2; Read security: 5
This assigns a priority to the Router Option Module that permits the
relative priority of multiple bridges to be managed. The range is 0
to 65535 with a default of 32768.
Spanning Tree/Maximum Age
Write security: 2; Read security: 5
This is the timeout value used by the Router Option Module to test
against the root device. The value is in one-tenth seconds with a
range between 60 (6.0 seconds) and 400 (40.0 seconds). The default
is 200 (20.0 seconds).
Spanning Tree/Hello Time
Write security: 2; Read security: 5
This is the time between the generation of configuration BPDUs
(Bridging Protocol Data Units) by the root bridge. The value is in
one-tenth seconds with a range between 10 (1.0 second) and 100
(10.0 seconds). The default is 20 (2.0 seconds).
Spanning Tree/Forward Delay
Write security: 2; Read security: 5
This is the time spent in the listening and learning state while mov-
ing from the blocking state to the forwarding state. The value is in
one-tenth seconds with a range between 40 (4.0 seconds) and 300
(30.0 seconds). The default is 150 (15.0 seconds).
Spanning Tree/LAN Port
The path cost and priority parameters for the Ethernet port are spec-
ified under this menu.
LAN Port/Active
Write security: 2; Read security: 5
The Ethernet port can be disabled when set to No. In this mode, no
bridge traffic will be forwarded in or out. Setting to Yes (def) allows
the port to participate in the spanning tree topology.
LAN Port/Path Cost
Write security: 2; Read security: 5
This is the cost of using the Ethernet port in the total cost of the path.
The range is from 1 to 65535 with a default of 100 (for 10 Mbits/sec-
ond).
4-16
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
LAN Port/Priority
Write security: 2; Read security: 5
The priority adjusts the relative priority of the Ethernet port among
the multiple bridge ports. The range is 0 to 255 with a default of 128.
Spanning Tree/Bridge Group 1
The Bridge Group 1 is either the first PPP BCP connection or part of
multiple DLCI destinations when running Bridge (RFC 1490) over
Frame Relay.
Bridge Group 1/Active
Write security: 2; Read security: 5
The Bridge Group 1 port can be disabled when set to No. In this
mode, no bridge traffic will be forwarded in or out. Setting to Yes
(def) allows the port to participate in the spanning tree topology.
Bridge Group 1/Path Cost
Write security: 2; Read security: 5
This is the cost of using the Bridge Group 1 in the total cost of the
path. The range is from 1 to 65535 with a default of 1302 (for 768
kbits/second).
Bridge Group 1/Priority
Write security: 2; Read security: 5
The priority adjusts the relative priority of the Bridge Group 1
among the multiple bridge ports. The range is 0 to 255 with a de-
fault of 128.
Spanning Tree/Bridge Group 2
Bridge Group 2 is part of multiple DLCI destinations when running
Bridge (RFC 1490) over Frame Relay.
Bridge Group 2/Active
Write security: 2; Read security: 5
This setup is exactly like Bridge Group 1 above.
Bridge Group 2/Path Cost
Write security: 2; Read security: 5
This setup is exactly like Bridge Group 1 above.
Bridge Group 1/Priority
Write security: 2; Read security: 5
This setup is exactly like Bridge Group 1 above.
61200350L1-1
Router Option Module User Manual
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Bridge/Address Table
The Router Option Module automatically maintains a table of MAC
addresses detected and associates those addresses with the LAN,
WAN0, or WAN1 port from which they were received. WAN0 rep-
resents Bridge Group 1, and WAN1 represents Bridge Group 2. This
menu permits the user to adjust the parameters or rules for the table
as addresses are learned.
Address Table/Aging
Write security: 3; Read security: 5
This is the maximum time an idle MAC address remains in the table
before being removed. The value is in minutes and can range from
0 (which means never age) to 65535. The default is 5.
Address Table/Forward Policy
Write security: 3; Read security: 5
When this parameter is set to Unknown (def), any bridge packet
with a destination MAC address that is not in the bridge table is for-
warded to all other ports. When set to Known, the packet with the
unknown destination MAC address is dropped and is not forward-
ed.
4-18
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Configuration/Security
The Security menu is used to set up the authentication parameters
needed to authenticate PPP connection. Also, the filter defines are
placed under this menu. Figure 4-6 shows the Security menu.
Configuration/Security Screen
Figure 4-6.
Security/Authentication
Write security: 1; Read security: 2
The method used for authenticating the PPP peer is selected here.
The possible values are:
None (def) - No attempt is made to authenticate the PPP peer.
Radius - The Router Option Module will act as a radius client and
authenticate the PPP peer using the radius server. The radius server
parameters must be set up properly for this to work.
PPP Profile - The PPP profile is used to authenticate the PPP peer.
See the Frame Relay section on page 4-26 for more information on au-
thenticating.
Security/Radius Server
The parameters for the radius server are configured in this menu.
The radius server can be used for authenticating a PPP peer (if de-
fined under Security/Authentication) and for Telnet server ses-
sions.
61200350L1-1
Router Option Module User Manual
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Radius Server/Primary Server
Write security: 1; Read security: 2
This is the IP address of the first RADIUS server that the Router Op-
tion Module should attempt to communicate with when authenti-
cating a PPP peer.
Radius Server/Secondary Server
Write security: 1; Read security: 2
This is the IP address of the back-up RADIUS server that the Router
Option Module should attempt to communicate with when the pri-
mary server does not respond.
Radius Server/UDP Port
Write security: 1; Read security: 2
This is the UDP port that the Router Option Module should use
when communicating with the RADIUS server. The default is 1645,
which is the commonly used port.
Radius Server/Secret
Write security: 0; Read security: 1
The RADIUS server and Router Option Module share this text
string, which is used by the RADIUS sever to authenticate the Rout-
er Option Module that is the RADIUS client. The factory default is
to not use a secret.
Radius Server/Retry Count
Write security: 1; Read security: 2
This is the number of times the Router Option Module should send
a request packet to the RADIUS server without a response before
giving up.
If the number of attempts to communicate with the primary server
is equal to the retry count, the secondary server (if defined) is tried.
If the secondary server does not respond within the retry count, the
PPP peer (or Telnet session) is not authenticated and is dropped.
The default is 5.
4-20
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Security/PPP
Write security: 1; Read security: 2
The PPP peer can be authenticated using three standard methods:
1. PAP (Password Authentication Protocol),
2. CHAP (Challenge Handshake Protocol)
3. EAP (Extensible Authentication Protocol).
The strength of the authentication is determined in the following or-
der:
1. EAP
2. CHAP
3. PAP (where EAP is the strongest and PAP is the weakest)
PAP is a clear-text protocol, which means it is sent over the PPP link
in a readable format.
Do not allow highly sensitive passwords to become compromised using this
method.
CHAP and EAP use a one-way hashing algorithm which makes it
virtually impossible to determine the password. EAP has other ca-
pabilities which allow more flexibility than CHAP.
The following selections are possible:
PAP, CHAP or EAP (def) - The Router Option Module will ask for
EAP during the first PPP LCP negotiation and allow the PPP peer to
negotiate down to CHAP or PAP.
CHAP or EAP - The Router Option Module will ask for EAP during
the first PPP LCP negotiation and allow the PPP peer to negotiate
down to CHAP but not PAP.
EAP - The Router Option Module will only allow EAP to be negoti-
ated. If the PPP peer is not capable of doing EAP, then the connec-
tion will not succeed.
61200350L1-1
Router Option Module User Manual
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Security/Filter Defines
The Router Option Module can filter packets based on certain pa-
rameters within the packet. The method used by the Router Option
Module allows the highest flexibility for defining filters and assign-
ing them to a profile. The filters are set up in two steps:
1. Defining the packet types,
2. Adding them to a list under the PPP profile or DLCI map.
See the section DLCI Mapping/Filters on page 4-32 for information on
how to set up filter profiles. This menu is used to define the individ-
ual filter defines based on packet type.
Filter Defines/MAC Filter Defines
Write security: 2; Read security: 3
The MAC filter is applied to bridge packets only. Bridge packets
which are forwarded by the bridge functionality of the Router Op-
tion Module are defined here. Up to 32 MAC defines can be specified.
Name
Identifies the filter entry
Src Addr
48-bit MAC source address used for compari-
son. (hexadecimal format)
Src Mask
Bits in the MAC source address which are com-
pared. (hexadecimal format)
Dest Addr
Dest Mask
MAC Type
Type Msk
48-bit MAC destination address used for com-
parison. (hexadecimal format)
Bits in the MAC destination address used for
comparison. (hexadecimal format)
16-bit MAC type field used for comparison.
(hexadecimal format)
Bits in the MAC type field used for comparison.
(hexadecimal format)
4-22
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Filter Defines /Pattern Filter Defines
Write security: 2; Read security: 3
The pattern filter is applied to bridge packets only. That is any pack-
et which is forwarded by the bridge functionality of the Router Op-
tion Module. Up to 32 pattern defines can be specified.
Name
Offset
Identifies the filter entry
Offset from beginning of packet of where to start the
pattern comparison
Pattern
Mask
64 bits used for comparison. (hexadecimal format)
Bits in the pattern to be compared.(hexadecimal for-
mat)
Filter Defines/IP Filter Defines
Write security: 2; Read security: 3
The IP filter defines apply to any IP packet, whether it is routed or
bridged. Up to 32 IP defines can be specified.
Name
IP Src
Identifies the filter entry
IP address compared to the source address.
(dotted decimal format)
Src Mask
IP Dest
Bits which are used in the source comparison.
(dotted decimal format)
IP address compared to the destination address.
(dotted decimal format)
Dest Mask
Src Port
Bits which are used in the destination compari-
son. (dotted decimal format)
IP source port number used for comparison.
Range: 0 to 65535. (decimal format)
Src Port
Cmpr
Type of comparison that is performed:
= -- port equal to
not = -- port not equal to
> -- port greater than
< -- port less than
None - the source port is not compared
61200350L1-1
Router Option Module User Manual
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Dst Port
IP destination port number used for comparison
Range: 0 to 65535. (decimal format)
Dst Port
Cmpr
Type of comparison that is performed:
= -- ports equal to
not = -- port not equal to
> -- port greater than
< -- port less than
None -- the destination port is not compared
Proto
Protocol used for comparison.
Range: 0 to 255. (decimal format)
Proto Cmpr
Type of comparison that is performed:
= -- protocols equal to
not = -- protocols not equal to
> -- protocols greater than
< -- protocols less than
None -- the protocol is not compared
TCP Est
Yes - only when TCP established
No - only when TCP not established
Ignore - ignore TCP flags
Filter Defines /IPX Filter Defines
Write security: 2; Read security: 3
The IPX filter defines apply to any IPX packet whether it is routed
or bridged. Also, any IPX encapsulation type will be accounted for.
Up to 32 IPX defines can be specified.
Name
Identifies the filter entry (15 characters, max)
32-bit source network address
Src Net
Src Mask
Bits in the source network address which are com-
pared. (hexadecimal format)
Dest Net
32-bit destination network address
Dest
Mask
Bits in the destination network address which are
compared. (hexadecimal format)
4-24
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Src
16-bit value which is the source socket.
Socket
Range:0-65535.
Src
Socket
Comp
Type of comparison that is performed:
= -- socket equal to
Not = -- socket not equal to
> -- socket greater than
< --socket less than
None -- no comparison is done on source socket
Dest
Socket
16-bit value which is the destination socket. Range
is 0-65535.
Dest
Socket
Comp
Type of comparison that is performed:
= -- socket equal to
Not = -- socket not equal to
> -- socket greater than
< -- socket less than
None -- no comparison is done on destination
socket
Type
8-bit value which is the IPX type
Type
Comp
Type of comparison that is performed:
= -- type equal to
Not = -- type not equal to
> -- type greater than
< -- type less than
None --no comparison is done on IPX type
61200350L1-1
Router Option Module User Manual
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Frame Relay
(also available via Front Panel)
Frame Relay is a connection-oriented service requiring circuits to be
configured by your carrier to establish a physical link between two
or more locations. Multiple virtual circuits (which appear as virtual
point-to-point links) can be run through the same physical connec-
tion.
There are two types of virtual circuits supported in Frame Relay:
Virtual Circuit Types
Description
Permanent Virtual Circuits PVCs are like dedicated point-to-point
(PVC)
private lines.
Since the physical connection is always
there in the form of a leased line, call
setup and tear down is done by a car-
rier via a network management sys-
tem.
Virtually all Frame Relay communica-
tion is done using PVCs.
Switched Virtual Circuit
(SVC)
SVCs require setup and tear down and
are generally not available from Frame
Relay carriers.
The Router Option Module supports PVCs only.
The Data Link Connection Identifier (DLCI) number identifies each
virtual circuit within a shared physical channel.
4-26
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Frame Relay/Maintenance Protocol
Write security: 3, Read security: 5
The Frame Relay maintenance protocol is used on the WAN port.
The maintenance protocol is used to send link status and virtual cir-
cuit information between Frame Relay switches and other devices
(such as routers) that communicate with them. Possible choices are
listed below.
Annex D(def) An ANSI standard that is most commonly used
in the US.
Annex A
LMI
The CCITT European standard.
Used by some carriers in the U.S.
Developed by a vendor consortium and known
as the “consortium” management interface spec-
ification.
Static
Select when there is no Frame Relay switch in
the circuit. The DLCIs are assigned in the DLCI
Mapping and must be the same for the device it
will communicate with.
Frame Relay/Polling Frequency
Write security: 3, Read security: 5
This parameter is the interval that the Router Option Module polls
the Frame Relay switch using the maintenance protocol selected
above. The Router Option Module is required to poll the Frame Re-
lay switch periodically to determine whether the link is active. The
value is in seconds and ranges from 5 to 30 seconds.
Frame Relay/DLCI Mapping
This menu allows each DLCI to be mapped to a particular protocol.
Each protocol parameter can be individually configured for each
DLCI. By factory default, the DLCI map is empty.
When empty and a maintenance protocol other than static is used,
the Router Option Module will poll the switch to determine which
DLCIs are active. These active DLCIs will attempt to determine the
IP and IPX addresses on the other end of the virtual circuit using In-
verse ARP (IARP). If there is a response, the network learned will be
added to the router tables and the virtual circuit will be treated as an
unnumbered interface. Bridge mode is not attempted in this case.
61200350L1-1
Router Option Module User Manual
4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
When more than one DLCI mapping is listed, the Router Option
Module will try to match the DLCIs learned from the Frame Relay
switch with the DLCI values in the map. If there is a match, the pro-
tocols specified in the map are used. However, if an active DLCI is
not in the list, the Router Option Module falls back to using IARP as
in the above paragraph to determine the protocols to use with that
particular virtual circuit.
If a static maintenance protocol is used, at least one DLCI mapping
must be specified.
If you want to...
Then...
Insert a new profile
Press the I key when over the Num col-
umn.
Explanation:
A new inserted profile will always be
set up with the default parameters.
Copy parameters from
an old profile to this
newly inserted profile:
Use the copy (C) and paste (P) keys.
Explanation:
Entire configuration trees can be copied
with this method.
Delete an unused profile Use the D key when the cursor is over
the number in the Num column.
Explanation:
Once deleted, the profile is gone perma-
nently as soon as the Connection List is
saved. Items may be deleted when DEL
appears below the status bar.
4-28
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
DLCI Mapping/Active
Write security: 3, Read security: 5
When this parameter is set to Yes (def), the mapping is used to de-
termine the protocols used. If set to No, the Router Option Module
will ignore the virtual circuit with this DLCI.
DLCI Mapping/DLCI
Write security: 3, Read security: 5
This is the DLCI associated with this virtual circuit. This value can
range from 16 to 1007.
DLCI Mapping/IP Map
Write security: 3, Read security: 5
This menu represents the IP protocol mapping that is to take place
for this DLCI.
IP Map/Active
Write security: 3, Read security: 5
When this is set to Yes (def), the Router Option Module will attempt
to transport IP packets for this DLCI. A setting of No means that no
IP traffic or route will be exchanged.
IP Map/IARP
Write security: 3, Read security: 5
When set to Yes (def), the Router Option Module will send Inverse
ARP packets in order to determine the IP address on the other end
of the virtual circuit. If the IARP is responded to, a route is placed
in the IP route table.
When set to No, the route address is to be assigned statically using
the IP Map/Far-End IP Address parameter.
IP Map/Far-End IP Address
Write security: 3, Read security: 5
This is the IP address of the device on the other end of the virtual cir-
cuit. When this DLCI becomes active, the Router Option Module
will add a route in the IP routing table.
IP Map/IP Netmask
Write security: 3, Read security: 5
The IP network mask to apply to the Far-End IP Address and Link
IP Address is specified here.
61200350L1-1
Router Option Module User Manual
4-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
IP Map/Link IP Address
Write security: 3, Read security: 5
The virtual circuit may require an IP address to be specified at this
DLCI, or numbered, interface. This address is used by the Router
Option Module to respond to Inverse ARP requests. If this IP ad-
dress is left as 0.0.0.0, the link is treated as unnumbered and the
Router Option Module responds to the Inverse ARP with its Ether-
net IP address.
IP Map/RIP Protocol
Write security: 3, Read security: 5
The RIP protocol can be specified per DLCI. The selections are:
Off (meaning no RIP packets are listened to or sent)
V1 (def) (which is RIP version 1)
V2 (which is RIP version 2)
IP Map/RIP Method
Write security: 3, Read security: 5
The method of which the RIP protocol is used is specified here:
None
All routes in the router table are adver-
tised out this virtual circuit with no modi-
fication of the metrics.
Split
Only routes not learned from this particu-
Horizon (def) lar virtual circuit are advertised.
Poison
Reverse
All routes are advertised, but the routes
learned from this port are “poisoned”
with an infinite metric.
4-30
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
IP Map/RIP Direction
Write security: 3, Read security: 5
This parameter allows the direction at which RIP advertisements
are sent and listened to be specified.
Tx and Rx
(def)
RIP advertisements are periodically transmitted
and are listened to on this virtual circuit.
Tx Only
RIP advertisements are periodically transmitted
but are not listened to on this virtual circuit.
Rx Only
RIP is not transmitted on this virtual circuit but
they are listened to.
DLCI Mapping/IPX Map
This menu represents the IPX protocol mapping that is to take place
for this DLCI.
IPX Map/Active
Write security: 3, Read security: 5
When set to Yes (def), the Router Option Module will attempt to
transport IPX packets for this DLCI.
When set to No, no IP traffic or route will be exchanged.
IPX Map/IARP
Write security: 3, Read security: 5
When set to Yes (def), the Router Option Module will send Inverse
ARP packets in order to determine the IPX network on the other end
of the virtual circuit. If the IARP is responded to, a route is placed
in the IPX route table.
When set to No, the IPX network is to be assigned to the link stati-
cally using the IPX Map/Link Network parameter.
IPX Map/Link Network
Write security: 3, Read security: 5
This is the IPX network of the link or of the other devices LAN.
When this DLCI becomes active, the Router Option Module will add
a route to this network in the IPX routing table. This address is also
used by the Router Option Module to respond to Inverse ARP re-
quests. If this IPX address is left as 0, the link is treated as unnum-
bered and the Router Option Module responds to the Inverse ARP
with its Ethernet IP address.
61200350L1-1
Router Option Module User Manual
4-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
DLCI Mapping/Bridge Map
This menu is used to permit bridging of packets over this DLCI.
Each DLCI or virtual circuit must be assigned a bridge group. The
bridge group treats all virtual circuits as one circuit. Bridge packets
destined to be transmitted out a particular bridge group are copied
and transmitted individually out each DLCI in the bridge group.
However, incoming bridge packets received from one DLCI are not
retransmitted out the other DLCIs in the same bridge group. Any
device in the bridge group must transmit to each DLCI. This re-
quires a fully meshed circuit, meaning each device has a virtual cir-
cuit to each other.
Bridge Map/Active
Write security: 3, Read security: 5
When set to Yes (def), the Router Option Module will bridge pack-
ets to and from this DLCI. Bridge packets are any packets that are
not IP or IPX packets except when the router is turned off, in which
case that particular router’s protocol packets are bridged.
When set to No, bridging will not occur.
Bridge Map/Bridge Group
Write security: 3, Read security: 5
The bridge group that this DLCI is part of is specified here as Group
1 or Group 2. These groups correspond to the spanning tree proto-
cols Bridge Group 1 and Bridge Group 2.
DLCI Mapping/Filters
The Router Option Module can block packets in and out of a PVC
port by use of the filters. They are set up in two steps:
1. Define the types of packets that would be of interest in the Con-
figuration/Security/Filter Defines menu, and
2. Set up the filter type and combination of defines that will cause a
packet block.
Filters/In from PVC
Write security: 2; Read security: 5
The packets which come into the Router Option Module via this
PVC can be filtered in three ways:
Disabled (def) - Turns off packet input filtering. No incoming pack-
ets from this PVC are blocked.
4-32
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Block All - All incoming packets from this PVC are blocked except
as defined in the Filters/In Exceptions list.
Forward All - All incoming packets from this PVC are not blocked
except as defined in the Filters/In Exceptions list.
Filters/In Exceptions
Write security: 2; Read security: 5
This is a list of up to 32 filter entries which can be combined using
the operations field. The operations are performed in the order they
appear on the list.
Active
Type
Turns this entry active when set to ON
Selects the filter define list to reference:
MAC - from the Configuration/Security/Filter
Defines/MAC Filter Defines list.
Pattern - from the Configuration/Security/Filter
Defines/Pattern Filter Defines list.
IP - from the Configuration/Security/Filter
Defines/IP Filter Defines list.
IPX - from the Configuration/Security/Filter
Defines/IPX Filter Defines list.
Filter List Name Selects between filters defined in the list.
Next Oper
The next operation to use to combine with the next
filter in the list:
End - the last filter to combination.
And - logically AND this filter with the next filter in
the list.
OR - logically OR this filter with the next filter in
the list.
61200350L1-1
Router Option Module User Manual
4-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Filters/Out to PVC
Write security: 2; Read security: 5
The packets which transmit out this PVC from the Router Option
Module can be filtered in three ways:
Disabled (def) - Turns off packet output filtering. No outgoing
packets to this PVC are blocked.
Block All - All outgoing packets to this PVC are blocked except as
defined in the Filters/Out Exceptions list.
Forward All - All outgoing packets to this PVC are not blocked ex-
cept as defined in the Filters/Out Exceptions list.
Filters/Out Exceptions
Write security: 2; Read security: 5
This is a list of up to 32 filter entries. The setup is exactly the same
as the Filter/In Exceptions list.
4-34
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Configuration/PPP Profile
The Router Option Module uses the PPP profile to specify the pro-
file used when connected using PPP. Figure 4-7 shows the PPP pro-
file menu.
Configuration/PPP Profile Screen
Figure 4-7.
PPP Profile/Authentication
The authentication menu contains the required parameters for the
authentication of the PPP peer and for being authenticated by the
PPP peer.
Authentication is applied between the Router Option Module and
the PPP peer as follows:
61200350L1-1
Router Option Module User Manual
4-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Authentication/Tx Method
Write security: 2; Read security: 3
This parameter specifies how the Router Option Module is to be au-
thenticated by the PPP peer. There are four possible selections. See
Security/PPP on page page 4-21 for an explanation of the three PPP
standard authentication types.
None (def)
The connection will not allow the PPP peer to
authenticate it.
PAP, CHAP or
EAP
The connection can be authenticated using
PAP, CHAP, or EAP.
CHAP or EAP
The connection can be authenticated using
CHAP or EAP only.
EAP
The connection will only allow authentication
by the peer using EAP.
Authentication/Tx Username
Write security: 1; Read security: 3
This is the username that is used when being authenticated by the
PPP peer.
Authentication/Tx Password
Write security: 0; Read security: 1
This is the password or secret that is used when being authenticated
by the PPP peer.
Authentication/Rx Username
Write security: 1; Read security: 3
This is the username used to authenticate the PPP peer.
Authentication/Rx Password
Write security: 0; Read security: 1
This is the password or secret that is used to authenticate the PPP
peer.
PPP Profile/IP
The IP menu contains the parameters for exchanging IP data with
the PPP peer.
4-36
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
IP/Mode
Write security: 3; Read security: 5
When set to On (def), this connection profile negotiates PPP IPCP
with the PPP peer for exchanging of IP packets.
IP/NAT
Write security: 3; Read security: 5
The Router Option Module can perform Network Address Transla-
tion. This feature is most widely used when connecting to the Inter-
net. The Ethernet network can consist of private network numbers.
When this profile is connected, all IP addresses on the Ethernet side
are translated into the one real IP address negotiated with the PPP
peer (ISP). Multiple stations on the Ethernet side can access the In-
ternet simultaneously. See the section IP/NAT on page page 4-7 for
more global options.
When set to On, the Router Option Module to perform NAT.
When set to Off (def), the unit will route across the connection nor-
mally.
IP/Route
The IP parameters are configured in this menu. UsuallytheRouterOp-
tion Module will automatically discover the PPP peer’s networks using PPP
IPCP and/or RIP.
Route/IP/Net
Write security: 3; Read security: 5
The PPP peer’s IP address or network can be set here, if known.
Leaving this at 0.0.0.0 means that the Router Option Module will de-
termine the PPP peer’s IP and network using the PPP IPCP.
Route/Netmask
Write security: 3; Read security: 5
This network mask is applied to the IP/NET address for determin-
ing the PPP peer’s network. If left as 0.0.0.0, a standard network
mask is used.
Route/Force IP
Write security: 3; Read security: 5
When set to Yes, the Router Option Module will force the PPP peer
to use the IP address in the IP/Net for this profile as its WAN IP ad-
dress. Normally this is set in the No (def) position.
61200350L1-1
Router Option Module User Manual
4-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
IP/RIP
The RIP parameters can be adjusted from their defaults under this
menu.
RIP/Mode
Write security: 3; Read security: 5
When set to On (def), the Router Option Module will perform RIP
over the WAN connection.
RIP/Protocol
Write security: 3; Read security: 5
The Router Option Module can perform version 1, V1 (def), or ver-
sion 2, V2, of RIP on this WAN connection.
RIP/Method
Write security: 3; Read security: 5
Split Horizon
Only routes not learned on the WAN con-
nection are advertised.
Poison Reverse (def) All routes are advertised, including
routes learned from the WAN connec-
tion. These routes are poisoned.
None
All routes are advertised, including
routes learned from the WAN connec-
tion. No attempt is made to poison these
routes
RIP/Direction
Write security: 3; Read security: 5
Tx and Rx (def)
Tx only
RIP advertisements are transmitted and
received on the WAN connection.
RIP advertisements are transmitted and
not received.
Rx only
RIP advertisements are received but not
transmitted.
4-38
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
RIP/Triggered
Write security: 3; Read security: 5
When set to Yes, only IP RIP updates are sent when the routing table
has changed and learned routes are not “aged.”
When set to No (def), updates are sent periodically.
PPP Profile/IPX
The IPX menu contains the parameters for exchanging IPX data
with the PPP peer.
IPX/Mode
Write security: 3; Read security: 5
When set to On (def), the connection profile to negotiate PPP IPXCP
with the PPP peer for exchanging of IPX packets.
IPX/Remote Network
Write security: 3; Read security: 5
A nonzero value in this remote network number will allow the
Router Option Module to add a route to the PPP peer’s network to
the routing table.
The Router Option Module normally will treat the WAN network as
an unnumbered link. This is usually referred to as being a “half-
router.” However, a PPP peer which wants to assign a network ad-
dress to the WAN link can do so, in which case the Router Option
Module will go into “full-router” mode.
IPX/Triggered
Write security: 3; Read security: 5
When set to Yes, only IPX RIP and SAP updates are sent when the
routing or service table has changed and learned routes are not
“aged.”
When set to No (def), updates are sent periodically based on the RIP
and SAP timers set in Configuration/IPX/RIP Timer and Configu-
ration/IPX/SAP Timer.
IPX/Type 20 Packets
Write security: 3; Read security: 5
For certain protocol implementations, like NetBIOS, to function in
the NetWare environment, routes must allow a broadcast packet to
be propagated throughout the IPX networks.
61200350L1-1
Router Option Module User Manual
4-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
The Type 20 IPX packet is used specifically for this purpose. This
causes special handling of this packet by the Router Option Module.
When a router receives this type of packet, it rebroadcasts it across
all interfaces except the one it is received on and includes the net-
work number of that interface in the data portion of the packet.
The IPX Router Specification from Novell notes that Type 20 packets
should not be propagated across slower links with bandwidths of
less than 1 Mbps (like ISDN). However, when set to Pass (def), the
Router Option Module will allow these packets to propagate over
the WAN connection. This facilitates dial-on-demand applications.
When set to Block, all Type 20 packets are not propagated across the
WAN connection.
PPP Profile/Bridge
The Bridge menu contains the parameters needed for exchanging
bridged packets with the PPP peer.
Bridge/Mode
Write security: 3; Read security: 5
When set to On (def), the Router Option Module will attempt to ne-
gotiate PPP BCP with the PPP peer. Bridging can be used even in
route mode only if the PPP peer cannot support certain PPP proto-
cols for that particular routing protocol. See Bridge/WAN IP Bridge
and Bridge/WAN IPX Bridge on page page 4-14 for further details.
PPP Profile/PPP
The Router Option Module supports the IETF standards for the
Point-to-Point Protocol. The PPP state machine running in the Rout-
er Option Module can be fine-tuned to support many applications
that can be employed. The configurable items under this menu can
be changed from their default values for special cases.
PPP/VJ Compression
Write security: 3; Read security: 5
When set to On, the Router Option Module will perform TCP/IP
header compression known as Van Jacobson compression to the
PPP peer. Normally, this is not necessary over ISDN connections.
Set to Off (def) to disable it.
4-40
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
PPP/Max Config
Write security: 3; Read security: 5
This value is the number of unanswered configuration requests that
should be transmitted before giving up on a call.
Possible values: 5, 10 (def), 15, 20.
PPP/Max Timer
Write security: 3; Read security: 5
This value is the number of seconds to wait between unanswered
configuration requests.
Possible values: 1 sec, 2 secs (def), 3 secs, 5 secs, 10 secs.
PPP/Max Failure
Write security: 3; Read security: 5
Due to the nature of PPP, configuration options may not be agreed
upon between two PPP peers. This value is the number of configu-
ration requests that should occur before an option is configuration-
rejected. This allows a connection to succeed that might otherwise
fail.
Possible values: 5 (def), 10, 15, 20.
PPP Profile/Filters
The Router Option Module can block packets in and out of a WAN
port by use of the filters. They are set up in two steps:
1. Define the types of packets that would be of interest in the Con-
figuration/Security/Filter Defines menu,
2. Set up the filter type and combination of defines that will cause a
packet block.
Filters/WAN-to-LAN (In)
Write security: 2; Read security: 5
The packets which come into the Router Option Module can be fil-
tered in three ways:
Disabled (def) Turns off packet input filtering. No incoming
packets are blocked.
Block All
All incoming packets from the WAN are
blocked except as defined in the Filters/In
Exceptions list.
61200350L1-1
Router Option Module User Manual
4-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Forward All
All incoming packets from the WAN are not
blocked except as defined in the Filters/In
Exceptions list.
Filters/In Exceptions
Write security: 2; Read security: 5
This is a list of up to 32 filter entries which can be combined using
the operations field. The operations are performed in the order they
appear on the list.
Active
Type
Turns this entry active when set to ON
Selects the filter define list to reference:
MAC - from the Configuration/Security/Filter
Defines/MAC Filter Defines list.
Pattern - from the Configuration/Security/Fil-
ter Defines/Pattern Filter Defines list.
IP - from the Configuration/Security/Filter
Defines/IP Filter Defines list.
IPX - from the Configuration/Security/Filter
Defines/IPX Filter Defines list.
Filter List
Name
Selects between filters defined in the list.
Next Oper
The next operation to use to combine with the
next filter in the list:
END - the last filter to combination.
AND - logically AND this filter with the next
filter in the list.
OR - logically OR this filter with the next filter
in the list.
4-42
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Filters/LAN-to-WAN (Out)
Write security: 2; Read security: 5
The packets which come out toward the WAN from the Router Op-
tion Module can be filtered in three ways:
Disabled (def) Turns off packet output filtering. No outgoing
packets are blocked.
Block All
All outgoing packets to the WAN are blocked
except as defined in the Filters/Out Exceptions
list.
Forward All
All outgoing packets to the WAN are not blocked
except as defined in the Filters/Out Exceptions
list.
Filters/Out Exceptions
Write security: 2; Read security: 5
This is a list of up to 32 filter entries. The setup is exactly the same
as the Filter/In Exceptions list.
61200350L1-1
Router Option Module User Manual
4-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Configuration/Management
The Router Option Module can be managed using Telnet, Simple
Network Management Protocol (SNMP), or the maintenance port.
See Appendix C for a description of the MIBs supported by the Rout-
er Option Module. Each of the three methods can be protected using
authentication. Figure 4-8 shows the Configuration/Management
menu.
Configuration/Management Screen
Figure 4-8.
Management/Telnet
Any Telnet client application can bring up a session to the Router
Option Module’s Telnet server using the standard Telnet TCP port.
Only one session is supported at a time. All sessions require a user
name and password.
Telnet/Server Access
Write security: 2; Read security: 5
When set to On (def), you can access the Router Option Module via
Telnet.
When set to Off, access is denied.
Telnet/User List
Up to four users can be configured for access to the Router Option
Module. Each user can be assigned a privilege and time-out.
4-44
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
User List/Name
Write security: 1; Read security: 3
A text string of the user name for this session.
User List/Authen Method
Write security: 1; Read security: 3
The user can be authenticated in two ways:
Password Used to authenticate the user
Radius
Used for authenticating the user
User List/Password
Write security: 0; Read security: 3
When the authenticating method is Password, this text string is
used for the password.
User List/Idle Time
Write security: 1; Read security: 3
When set to nonzero, the session is automatically logged out when
no activity occurs for this amount of time. The range is 0 to 255 and
is in minutes. The default is 10 minutes, and a setting of 0 will never
time out the session. When a time-out occurs during an edit session,
all changes are saved.
User List/Level
Write security: 0; Read security: 1
This is the security level privilege that is assigned for this user. See
Security Levels for an explanation of what those levels imply. Level
0 is the default.
Management/SNMP
The Router Option Module is an SNMP agent. It can respond to
Get-Requests and generate traps. These two lists set up the manag-
er, communities, and levels. See Appendix D for more information on
SNMP.
61200350L1-1
Router Option Module User Manual
4-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
SNMP Access
Write security: 3; Read security: 5
When set to:
No - SNMP access is denied.
On (def) - the Router Option Module will respond to SNMP manag-
ers based on the following lists.
SNMP/Communities
This list is used to set up to eight SNMP communities’ names that
the Router Option Module will allow. Factory default sets the com-
munity “public” with “Get” privileges.
Communities/Name
Write security: 1; Read security: 3
This is a text string for the community name.
Communities/Privilege
Write security: 1; Read security: 3
The access for this manager can be assigned three levels.
None - No access is allowed for this community or manager.
Get - Manager can only read items.
Get/Set - Manager can read and set items.
Communities/Manager IP
Write security: 1; Read security: 3
This is the IP address of SNMP manager. If set to 0.0.0.0, any SNMP
manager can access the Router Option Module for this community.
SNMP/Traps
The Router Option Module can generate SNMP traps. See Appendix
D for trap types supported. This list allows up to four managers to
be listed to receive traps.
Traps/Manager Name
Write security: 2; Read security: 4
This is the text string describing the name of the entry. It is intended
for easy reference and has no bearing on the SNMP trap function.
Traps/Manager IP
Write security: 2; Read security: 4
This is the IP address of the manager that is to receive the traps.
4-46
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Management/Maint Port
The Router Option Module has an EIA-232 connector on the back of
the unit. The setup for that port is under this menu.
Maint Port/Password Protect
Write security: 0; Read security: 1
When set to No, the maintenance port is not password protected.
When set to On (def), the Router Option Module will prompt for a
password upon startup.
Maint Port/Password
Write security: 0; Read security: 1
This is the text string that is used for comparison when password
protecting the maintenance port. By default, no password is en-
tered.
The security level for the maintenance port is always set to 0. This gives
full access to all menus.
Maint Port/Baud Rate
(also available via Front Panel Terminal/Rate)
Write security: 5; Read security: 5
This is the asynchronous rate that the maintenance port will run.
Possible values: 300, 1200, 2400, 4800, 9600 (def), 19200, 38400,
57600.
Maint Port/Data Bits
(also available via Front Panel Terminal/Data Bits)
Write security: 5; Read security: 5
This is the asynchronous bit rate that the maintenance port will run.
Possible values: 7 or 8 (def) bits.
Maint Port/Parity
(also available via Front Panel Terminal/Parity)
Write security: 5; Read security: 5
This is the asynchronous parity that the maintenance port will run.
Possible values: None (def), Odd, or Even.
61200350L1-1
Router Option Module User Manual
4-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuration Overview
Maint Port/Stop Bits
(also available via Front Panel Terminal /Stop Bits)
Write security: 5; Read security: 5
This is the stop bit used for the maintenance port.
Possible values: 1 (def), 1.5 or 2.
Configuration/Terminal Mode
This is an activator which places the Router Option Module termi-
nal session into a command prompt mode. All menu options are ac-
cessible during this mode. See Appendix E for the command
structure and command list. Type exit to leave the terminal mode
and return to the menus.
4-48
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Statistics
Chapter 5
STATUS MENU
The Router Option Module’s Status menu contains comprehensive
status and diagnostic information used in verifying configuration
and identifying problems. The menus are divided into protocol
types and sessions. Figure 5-1 shows the Status menu.
Status Screen
Figure 5-1.
61200350L1-1
Router Option Module User Manual
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Status/Sessions
This menu contains the current status of all dial-in sessions and
spanning tree ports.
Sessions/PPP Session
Read security: 5
This menu reflects the results of PPP negotiations, user name, time
connected, and data rates for the session.
Name
PPP Links
BCP
Description
Reflects LCP layer active
Shows UP if PPP Bridge Control Protocol has
negotiated successfully
IPCP
Shows UP if PPP IP Control Protocol has nego-
tiated successfully
IPXCP
Shows UP if PPP IPX Control Protocol has
negotiated successfully
Uptime
Tx Pkts
Rx Pkts
Tx Bytes
Rx Bytes
Tx Rate
Rx Rate
Displays how long the call has been connected
Number of packets transmitted
Number of packets received
Number of bytes transmitted
Number of bytes received
Current application data transmission rate
Current application data reception rate
5-2
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Sessions/DLCI Table
The status of all virtual circuits is displayed here.
DLCI - The DLCI that is associated with this virtual circuit.
State - The state of the virtual circuit:
State
Definition
Inactive
The circuit exists but has been deactivated by the
Frame Relay switch.
Exists
The circuit exists at this point and should be acti-
vated soon.
Active
Off
The circuit is fully active.
The circuit has been turned off by the DLCI map-
ping active selection.
Tx Frames
Number of Frame Relay packets that have been
transmitted via this DLCI.
Rx Frames Number of Frame Relay packets that have been
received via this DLCI.
Tx Bytes
Rx Bytes
IP SubIfc
Number of Frame Relay bytes that have been trans-
mitted via this DLCI.
Number of Frame Relay bytes that have been
received via this DLCI.
The IP router port assigned for this DLCI. Possible
ports are fr0, fr1, … , fr9. None means that this DLCI
is not used for routing IP.
IPX SubIfc The IPX router port assigned for this DLCI. Possible
ports are fr0, fr1, … , fr9. None means that this DLCI
is not used for routing IPX.
Bridge
Group
The bridge group that this DLCI belongs to (Group 1
or Group 2). None means that this DLCI is not used
for bridging.
61200350L1-1
Router Option Module User Manual
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Sessions/Spanning Tree
Read security: 5
When Bridge mode and Spanning Tree mode are active, this reflects
the current state of the LAN and WAN ports. The following can ap-
pear:
Name
Off
Description
Appears when spanning tree mode is disabled
Disabled
Port is not connected (for WAN) or disabled in
configuration
Listening
Learning
Port is in the listening state
Port is in the learning state
Forwarding Port is in the forwarding state with the following
possible properties:
root - root port
designated - designated port
Blocking
Port is in the blocked state
Status/ARP Cache
Read security: 5
This lists the contents of the Router Option Module’s ARP table. All
resolved cache entries time out after 20 minutes. Unresolved entries
time out in 3 minutes.
Name
Description
ARP Cache/IP Address
IP address used for resolving
MAC address
ARP Cache /MAC Address Ethernet address resolved
(0=no resolution)
ARP Cache/Time
Minutes since entry was first
entered
5-4
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Status/Bridge Table
Read security: 5
This lists the contents of the Router Option Module’s bridge table.
Name Description
Bridge Cache/MAC Ethernet address for device learned
Address
Bridge Cache/Port
Port device learned from: LAN,
WAN0, or WAN1
Bridge Cache/TTL
Seconds until address is removed
from table
Status/IP Routes
Read security: 5
This lists the contents of the Router Option Module’s IP router table.
Name
Description
IP Routes/IP Address Network or host destination address
IP Routes/Netmask
Network mask applied to the destination
address
IP Routes/Gateway
IP Routes/Port
Host or router to receive this packet
Port gateway is located on:
local
Sent directly to the Router Option Module
route
eth0
Router Option Module’s ethernet port
wan0
Router Option Module’s first PPP bundle
fr 0 . . . fr 9
Router Option Module is connected up to
10 DLCIs
IP Routes/Use
Number of times the Router Option Mod-
ule has referenced the route
61200350L1-1
Router Option Module User Manual
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Name
Description
IP Routes/Flags
Important tags associated with this route
entry:
H - route is a host route
G - route is a gateway route
D - route learned dynamically from RIP
I - route learned from an ICMP redirect
P - route is private and is not advertised
with RIP
T - route is to a triggered port (updates
only when table changes)
IP Routes/Hops
IP Routes/TTL
Number of routers that must go through
to get to destination. Ranges from 0-15 or
16 for infinite (can’t get there from here).
Seconds until address is removed from
table or “zombied.” Value of 999 means
route is static.
5-6
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Status/IPX Routes
Read security: 5
This lists the contents of the Router Option Module’s IPX router ta-
ble.
Name
Description
IPX Routes /Network
IPX Routes /Gateway
Network destination address
Node or Ethernet address of gateway to
receive this packet
IPX Routes /Port
Port gateway is located on:
local
Sent directly to the Router Option Module
router
eth0
Router Option Module’s ethernet port
wan0
Router Option Module’s first PPP bundle
fr 0 . . . fr 9
Router Option Module is connected up to
10 DLCIs
IPX Routes /Use
IPX Routes/Hops
Number of times the Router Option Mod-
ule has referenced the route
Number of routers that must go through to
get to destination. Ranges from 0-15 or 16
for infinite (can’t get there from here).
IPX Routes/Ticks
IPX Routes/TTL
Router-determined value for representing
time packets take to reach the network des-
tination. One tick is equivalent to one-eigh-
teenth of a second.
Seconds until address is removed from
table. Value of 999 means route is static.
61200350L1-1
Router Option Module User Manual
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Status/IPX Servers
Read security: 5
This lists the contents of the Router Option Module’s IPX server ta-
ble.
Name
Description
IPX Servers/Type
IPX Servers/Name
IPX Servers/Network
IPX Servers /Address
IPX Servers/Socket
IPX Servers/Hops
The server type
The server name
The server network address
The servers node address
The servers socket address
Number of routers that must go
through to get to server.
Ranges from 0-15 or 16 for infinite.
PX Servers/TTL
Seconds until address is removed
from table. Value of 999 means
server is static.
Status/WAN Stats
Read security: 5
This menu contains generic WAN statistics on HDLC hardware
port.
Name
Description
Tx Bytes
Rx Bytes
Total number of raw bytes sent out HDLC port 1
Total number of raw bytes received in HDLC
port 1
Rx CRCs
Total number of CRC errors detected on HDLC
port 1
Clear Counts
When activated, clears all WAN stat counts
5-8
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Status/LAN Stats
Read security: 5
This menu contains statistics for the Ethernet port.
Name
Description
Tx Packets
Rx Packets
Tx Errors
Packets transmitted out the Ethernet port
Packets received from the Ethernet port
Total transmit errors encountered on Ethernet
port
Single Collisions - total single collisions before
successful transmission
Multiple Collisions - total multiple collisions
before successful transmission
Excessive Collisions - total collisions that
resulted in packet being dropped
Deferred Transmissions - total packets deferred
due to collisions
Carrier Sense Errors - total carrier sense errors
encountered (no link integrity)
Rx Errors
Total packets received in error and dropped
CRCs - total packets detected with CRC errors
Giants - total packets received that were greater
than 1518 bytes
Runts - total packets received that were less than
64 bytes
Rx Collisions - total collision occurred during
reception
Clear Counts
When activated, clears all LAN Stat counts.
61200350L1-1
Router Option Module User Manual
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Status/IP Stats
Read security: 5
This menu contains IP statistics that can be useful when diagnosing
problems. All are taken from the SNMP MIB-2 variables.
TCP failed attempts
TCP passive connections
TCP current connections
TCP segments sent
TCP segments received
Total TCP resets
Active TCP connections
Total TCP retransmits
UDP datagrams sent
No application at dest. port
UDP datagrams received
UDP bad packets
ICMP redirected messages
ICMP packet errors
ICMP time-outs received
ICMP messages sent
ICMP messages received
ICMP specif if errors
IP datagrams reassembled
IP datagrams sent
IP datagrams received
Total forwarded datagrams
IP reassembly time-out
Discarded routing entries
Total IP fragments
Failed fragments
IP reassembly failures
Disassembled fragments
Errorfree discards
Routeless discards
Default TTL
Bad IP addresses
Successful fragments
Bad header packets
Sent datagrams to upper layers
Datagrams discarded
Bad protocol discards
Clear Counts - clears all IP stats
5-10
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
Viewing Statistical Information
(Front Panel Interface)
To view statistical information:
Step
Action
Result
1
2
3
4
Select 1)STATUS from the Main menu.
Select Port Status.
Choose the Router Option Module.
A menu appears.
From this menu, choose to view:
WAN
The first Statistics
screen appears
LAN
Reset the statistics.
5
Scroll through the remaining screens
using the arrow keys.
Statistic counts are
running totals for the
current day (i.e.,
since 12 AM).
Router Statistics Available on Front Panel
The following information is displayed when the Router module is
selected.
Status
WAN
LAN
TX BYTE
RX BYTE
RX CRC
TX PCKTS
RX PCKTS
TX ERRORS
RX ERRORS
61200350L1-1
Router Option Module User Manual
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Statistics
5-12
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics
Chapter 6
TEST MENU
The Router Option Module’s Test menu contains built-in tests that
can be used to diagnose problems. Figure 6-1 shows the Test menu
screen. The following tests are listed below.
Test Screen
Figure 6-1.
Test Menu/Echo Request
Write security: 4, Read security: 5
When activated, the echo request test will begin sending continuous
PPP echo request packets to any open LCP ports. Results are dis-
played on the screen. This test is not used in the Frame Relay mode.
61200350L1-1
Router Option Module User Manual
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Diagnostics
LOGS MENU
The Logs menu contain logs displaying important information
about the running condition of the Router Option Module. The logs
can be set to capture diagnostics of error conditions only by way of
a log level. The levels are divided up as follows:
Level
Description
0
1
2
3
4
5
6
Fatal event (causes reset)
Critical event
Error event
Warning event
Notify event
Informational event
Debugging event
Figure 6-2 shows the Logs menu. The three logs available are listed
after the figure.
Logs Screen
Figure 6-2.
6-2
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Diagnostics
Logs/Syslog Host
Set this to the IP address or domain name (if DNS configured) of the
sys log host device. All log events are sent to this device.
Logs/PPP Log
Information pertaining to the PPP negotiation and authentication
will be logged here.
PPP Log/Active
When set to Yes (def), PPP events below or equal to this level are
logged.
PPP Log/Wrap
When set to Yes (def), new PPP events will overwrite old PPP events
when the log is full. When set to No, all logging will stop when the
log is full.
PPP Log/Level
In order to log events, they must be at or below this level. Range is
0 to 6. The default is 3.
PPP Log/View
This menu displays the log list. The fields are as follows:
Date/Time - Date and time event occurred.
Level - Level associated with this event (0-6).
Message - Text message for this event. If message is too long to fit
on the line, another event appears below it continuing the message.
PPP Log/Clear
This clears the log when activated.
61200350L1-1
Router Option Module User Manual
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Diagnostics
Logs/Connection Log
Information pertaining to the connection over the T1 link.
Connection Log/Active
When set to Yes (def), connection events less than or equal to the log
level are logged into the log.
Connection Log/Wrap
When set to Yes (def), new connection events will overwrite old
connection events when the log is full.
When set to No, all logging will stop when the log is full.
Connection Log/Level
In order to log events, they must be at or below this level. Range is
0 to 6. The default is 3.
Connection Log/View
This menu displays the log list. The fields are as follows:
Date/Time - Date and time event occurred.
Level - Level associated with this event (0-6).
Message - Text message for this event. If message is too long to fit
on the line, another event appears below it continuing the message.
Connection Log/Clear
This clears the log when activated.
Logs/Network Log
Information pertaining to the routing protocols is placed in this log.
Network Log/Active
When set to Yes (def), call events below or equal the log level are
logged into the log.
6-4
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Diagnostics
Network Log/Wrap
When set to Yes (def), new Network events will overwrite old Net-
work events when the log is full.
When set to No, all logging will stop when the log is full.
Network Log/Level
In order to log events, they must be at or below this level. Range is
0 to 6. The default is 3.
Network Log/View
This menu displays the log list. The fields are as follows:
Date/Time - Date and time event occurred.
Level - Level associated with this event (0-6).
Message - Text message for this event. If message is too long to fit
on the line, another event appears below it continuing the message.
Network Log/Clear
This clears the log when activated.
61200350L1-1
Router Option Module User Manual
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Diagnostics
6-6
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility Menu
Chapter 7
TERMINAL MODE
Utilities Menu
TheRouter Option Module has utilities embedded in itto help in manag-
ing and testing the network and to facilitate software upgrades. Figure
7-1 shows the Utilities menu.
Utilities Screen
Figure 7-1.
61200350L1-1
Router Option Module User Manual
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: Utility Menu
Utilities/Ping
Write security: 4; Read security: 5
This option is available under the Test Menu via the Front Panel.
The ping menu is used to send ICMP ping messages to hosts. The
following items are under the this menu:
Ping Menu
Start/Stop
Description
Activator to start and cancel a ping test
Host Address
IP address or domain name (if DNS is config-
ured) of device to receive the ping
Size
Total size of ping to send. Range is 40 (def) to
1500 bytes
No. of Packets
No. of Transmits
No. of Receives
% Loss
Total packets to send every two seconds
Total packets sent (read only)
Total packets received (read only)
Percentage loss based on ping returned from
host (read only)
Utilities/Telnet Client
Write security: 4; Read security: 5
The Telnet menu can be used to activate the Telnet client function in
the Router Option Module.
Host - IP address or domain name (if DNS is configured) of Telnet
server. By default, the standard TCP server port is used. However,
a nonstandard port can be specified here with the IP address or do-
main name separated by a colon (:).
Activate - Starts Telnet client function. The key combination
Control ] cancels the session.
Utilities/Upgrade Menu
Write security: 2; Read security: 3
The Router Option Module firmware can be upgraded using this
menu.
7-2
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: Utility Menu
Upgrade/Transfer Method
The two methods for upgrading are TFTP and XMODEM.
1. TFTP requires a TFTP server running somewhere on the net-
work. The Router Option Module starts a TFTP client function
which gets the upgrade code from the TFTP server.
2. Selecting XMODEM will load the upgrade code through the
maintenance port using any PC terminal emulator with XMO-
DEM capability.
Upgrade/TFTP Host
This is required when the transfer method is TFTP. It is the IP ad-
dress or domain name (if DNS is configured) of the TFTP server.
Upgrade/Filename
This is required when the transfer method is TFTP. It is the case-sen-
sitive filename which is the upgrade code.
Upgrade/Status
This appears when TFTP is used. It displays the status of the trans-
fer as it happens. Any error or success message will be displayed
here.
Upgrade/Start Transfer
This activator is used when the configurable items in this menu are
complete.
Once started, the Router Option Module will prompt for erasing the flash.
When the flash is erased and the upgrade transfer fails, do not turn off the
unit. Retry the transfer until successful. Otherwise, if power is removed
before upgrade has finished, the upgrade will have to occur from the
maintenance port using XMODEM. If this happens, set a PC terminal
emulation program to 9600 baud and attach to the Router Option
Module’s maintenance port. Press Return to display a simple terminal
menu for upgrading. This menu appears when the flash code has been
erased or is corrupt. The menu will also appear if you power up and hold
down the SELECT key for at least five seconds.
61200350L1-1
Router Option Module User Manual
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: Utility Menu
Upgrade/Abort Transfer
Use this activator to cancel any TFTP transfer in progress.
Upgrade/TFTP Server
Set to Yes, to allow another Router Option Module to upgrade its
code using TFTP client. This, in effect, turns on the Router Option
Module TFTP server function and allows its code to be “cloned.”
Set to No (def) to deny any request from TFTP clients.
Utilities/Exit
Write security: 5; Read security: 5
Activating this feature will exit the terminal session from the main-
tenance port or Telnet. It is equivalent to the key combination
Control L.
Front Panel
Software Revision
This menu displays the software version and checksum and is
shown in Figure 7-2, below. Press CANCEL to return to the Util
menu.
CMD Mode
Factory use only.
ADTRAN ROUTER
VER 2.200 17AB
System Statistics Screen
Figure 7-2.
7-4
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Pinouts
Appendix A
The following table gives the pin assignments for the Router Op-
tion Module card connectors. For more information on these con-
nectors, see Chapter 2: Installation.
Table A-1: Pin Assignments for Control Connector
RJ Pin #
Function
Direction
1
2
3
4
5
6
7
8
GND
TRS
TD
I
I
DSR
RD
O
O
O
I
CTS*
DTR
DCD
O
*Used for hardware flow control
Table A-2: 10BaseT Ethernet
Function
Pin 1
Pin 2
Pin 3
Pin 6
RX1
RX2
TX1
TX2
10BT
61200350L1-1
Router Option Module User Guide
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Pinouts
A-2
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Appendix B
SPECIFICATIONS AND FEATURES
This section describes the standard specifications and features in-
corporated in the Router Option Module.
Ethernet Interface (LAN)
Ethernet/IEEE 802.3 10BaseT.
Display
Available through terminal interface, or Telnet session, or TSU
XX0 Front Panel.
Environmental
• Operating Temperature: 0 - 50 °C
• Storage Temperature: 20 - 70 °C
• Relative Humidity: Up to 95% noncondensing
Physical
• Dimensions: 1-9/16" H x 6-1/2" W x 8-1/4" D
• Weight: 2.5 lbs
Power
• 120 VAC, 60 Hz, 7.5 W typical
Agency Approvals
• FCC Part 15, Class A
• UL and CUL
61200350L1-1
Router Option Module User Guide
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: Specifications
B-2
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Log Messages
Appendix C
The Router Option Module Log menu contains messages of
events that occur. The definitions for some of those log messages
are as follows:
PPP Log Messages
BCP <X> down
level 5
Bridge Control Protocol port <X> has been dropped between
Router Option Module and PPP peer.
BCP <X> up
level 5
Bridge Control Protocol port <X> has been successfully negotiat-
ed between Router Option Module and PPP peer.
CCP <X> down
level 5
Compression Control Protocol port <X> has been dropped be-
tween Router Option Module and PPP peer.
CCP <X> up
level 5
Compression Control Protocol port <X> has been successfully ne-
gotiated between Router Option Module and PPP peer.
CHAP authen failed
level 3
The PPP peer has rejected the Router Option Module’s username
and/or password used for authenticating. Check to make sure the
Configuration/Connection List/Authentication parameters Tx
Method, Tx Username, and Tx Password are correct.
61200350L1-1
Router Option Module User Guide
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Log Messages
EAP authen failed
level 3
The PPP peer has rejected the Router Option Module’s username
and/or password used for authenticating. Check to make sure the
Configuration/Connection List/Authentication parameters Tx
Method, Tx Username, and Tx Password are correct.
IPCP <X> down
level 5
IP Control Protocol port <X> has been dropped between Router
Option Module and PPP peer.
IPCP <X> up
level 5
IP Control Protocol port <X> has been successfully negotiated be-
tween Router Option Module and PPP peer.
IPXCP <X> down
level 5
IPX Control Protocol port <X> has been dropped between Router
Option Module and PPP peer.
IPXCP <X> up
level 5
IPX Control Protocol port <X> has been successfully negotiated
between Router Option Module and PPP peer.
LCP <X> down
level 5
Link Control Protocol port <X> has been dropped between Router
Option Module and PPP peer.
LCP <X> up
level 5
Link Control Protocol port <X> has been successfully negotiated
between Router Option Module and PPP peer.
Link is looped back
level 3
The Router Option Module has dialed a location which is looping
back all data. Essentially, it has negotiated PPP with itself.
C-2
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Log Messages
Negot not converging
level 2
Negotiation of the LCP layer is unattainable due to misconfigura-
tion or the Router Option Module or PPP peer is requiring authen-
tication and the other is refusing.
No IP addr for peer
level 2
The Router Option Module cannot continue the connection be-
cause there was no IP address received from the PPP peer or it was
not set in Configuration/Connection List/IP/Route/IP/Net pa-
rameter.
No Response from peer
level 2
The Router Option Module has dialed or answered a call and no
PPP negotiation packets were seen.
PAP authen failed
level 3
The PPP peer has rejected the Router Option Module’s username
and/or password used for authenticating. Check to make sure the
Configuration/Connection List/Authentication parameters Tx
Method, Tx Username, and Tx Password are correct.
Peer failed CHAP authen
level 3
The PPP peer’s reported CHAP username and/or password does
not match the Router Option Module’s parameters. This is most
likely caused by PPP peer sending an incorrect username and/or
password. Make sure the Configuration/Connection List/Au-
thentication parameters Rx Username and Rx Password are cor-
rectly entered. Also, if using RADIUS, check that the server is
configured and running properly.
Peer failed EAP authen
level 3
The PPP peer’s reported EAP username and/or password does
not match the Router Option Module’s parameters. This is most
likely caused by PPP peer sending incorrect username and/or
password. Make sure the Configuration/Connection List/Au-
thentication parameters Rx Username and Rx Password are cor-
rectly entered. Also, if using RADIUS, check that the server is
configured and running properly.
61200.350L2-1
Router Option Module User Guide
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Log Messages
Peer failed PAP authen
level 3
The PPP peer’s reported PAP username and/or password does
not match the Router Option Module’s parameters. This is most
likely caused by PPP peer sending incorrect username and/or
password. Make sure the Configuration/Connection List/Au-
thentication parameters Rx Username and Rx Password are cor-
rectly entered. Also, if using RADIUS, check that the server is
configured and running properly.
Peer refused authen
level 3
The PPP peer would not allow the Router Option Module to au-
thenticate it using the method set in Configuration/Security/PPP.
Peer refused SpanTree
level 4
The PPP peer would not participate in the Spanning Tree protocol.
This is a warning message only. Bridging will still occur across the
WAN port so care must be taken that no loop topologies exist
across the connection.
PPPtx[x] …
level 6
Advance debugging decode of transmitted PPP configuration
packets.
PPPrx[x] …
level 6
Advanced debugging decode of received PPP configuration pack-
ets.
C-4
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Log Messages
Call Log Messages
Power Up - last down cause: <reason>
level 0 (displayed as level 1 after the unit is reset)
This is the <reason> for the last reset. Most are caused by internal
errors. Possible reasons are:
Bus error
Bad address occurred on the internal bus
General operating system error
Mail resources used up or lost
Fatal error in protocol stack
General error
Kernel error
No SBCs
Router stack error
General panic
No rip
Rip tasks could not start
Out of memory
Out of TCP ports
Unknown error
Set timer error
Out of available memory
All TCP ports are used up
Unknown fatal error has occurred
Cannot set real-time clock
Software watchdog
reset
Software watchdog was not updated
61200.350L2-1
Router Option Module User Guide
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Log Messages
Network Log Messages
Attempting to add bad IP iface route: ifnum=<inter> dest=<ip>
level 4
An IP address <ip> could not be used for the interface number
<inter>.
DHCP couldn't alloc mem
level 1
A DHCP response could not be generated due to memory alloca-
tion problems.
DHCP response sent
level 4
A DHCP response was successfully sent to requesting device.
DHCP socket failed
level 1
Internal error occurred when attempting to start DHCP server.
DHCP: Host not added to ARP table
level 2
The DHCP server could not add requesting host to ARP table.
Installing bad default route: ifnum=<inter> metric=<hops>
gw=<ip>
level 6
The Router Option Module did not install a default route because
the <inter> or <hops> was zero.
Rejecting packet with Source Routing option: src=<srcip>
dest=<destip>
level 4
The Router Option Module has dropped a source-routed IP pack-
et due to invalid parameters.
setmask: local IP iface(0), not done
level 6
Debug error used in determining router stack problems.
syslog: bad host
level 2
Syslog function cannot use host name or IP set in Configuration/
Logs/Syslog Host.
C-6
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Log Messages
syslog: no port
level 2
Syslog function cannot open port to send Log entries.
TEL: Telnet Session Closed
level 4
Telnet server session has been closed.
telclient bad host
level 2
Telnet client could not use host name or IP address set in Config-
uration/Utilities/Telnet Client/Host.
telclient bad init
level 2
Telnet client could not initialize a session.
Telnet Client: Clr TCBF_BUFFER flag failed
level 6
Debugging message related to Telnet client function.
Telnet Client: Set TCBF_DONTBLOCK flag failed
level 6
Debugging message related to Telnet client function.
Telnet Client socket failed
level 2
Telnet client function could not open TCP socket.
Telnet server connect to <ip>
level 4
Telnet server has connected to Telnet client with IP address <ip>.
Telnet Session Closed
level 4
Telnet server has closed connection.
Telnet Session failed, error <errnum>
level 2
Telnet server could not connect to Telnet client due to error.
TELNETD: accept failed
level 2
Telnet server could not open TCP socket to incoming Telnet client.
61200.350L2-1
Router Option Module User Guide
C-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Log Messages
TELNETD: Set TCPC_LISTENQ failed
level 6
Debugging message related to Telnet server function.
TELNETD: Clr TCBF_BUFFER flag failed
level 6
Debugging message related to Telnet client function.
TELNETD: could not obtain peer ip
level 2
Telnet server function could not get IP address of Telnet client.
TELNETD: Session failed, error
level 2
A Telnet server session has failed because of an error.
TELNETD: Set TCBF_DONTBLOCK flag failed
level 6
Debugging message related to Telnet client function.
TELNETD: SOCKET creation error
level 2
Telnet server could not be started due to TCP socket error.
TFTP: can't get to host
level 2
TFTP client could not get to host.
TFTP client: unable to open port
level 2
TFTP client function could not open a UDP port.
TFTP: error rcvd - <message>"
level 2
Received error with <message> from TFTP server.
TFTP: lost communication
level 2
Lost communication to TFTP client or server during transfer.
TFTP server: unable to open port
level 2
TFTP server function could not open a UDP port.
C-8
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SNMP
Appendix D
UNDERSTANDING SNMP
The Simple Network Management Protocol (SNMP) is the de facto
standard for managing commercial Transmission Control Proto-
col/Internet Protocol (TCP/IP) networks. It allows vendor equip-
ment to be managed from a single control console.
The term SNMP broadly refers to the message protocols used to
exchange information between the network and the managed de-
vices, as well as to the structure of network management databas-
es.
SNMP Components:
SNMP has three basic components: Network Manager, Agent,
and MIB.
Network Manager
• A control program that collects, controls, and presents data
pertinent to the operation of the network devices.
• Resides on a network management station.
Agent
• A control program that responds to queries and commands
from the network manager.
• Returns requested information or invokes configuration
changes initiated by the manager.
• Resides in each network device connected.
61200350L1-1
Router Option Module User Guide
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: SNMP
MIB
• An index to the organized data within a network device.
• Defines the operating parameters that can be controlled or
monitored.
When requesting the network manager to retrieve or modify a
particular piece of information about a network device, the net-
work manager transmits the request to that network device. The
agent in that device interprets the incoming request, performs the
requested task, and sends its response to the network manager.
The network manager collects all the data from the various net-
work devices and presents it in a consistent form.
Using SNMP Version 1, the network manager can issue three
types of commands:
GetRequest: This command retrieves a single item or the first in
a series from a network device.
GetNextRequest: This command retrieves the next item in a se-
ries from a network device.
SetRequest: This command writes information to a network de-
vice.
The network device issues two types of messages:
GetResponse: This message is the response to a network manag-
er GetRequest or GetNextRequest command.
Trap: This is an unsolicited message issued by a network device
to report an operational anomaly or an alarm condition to the net-
work manager.
These messages are typically encased within informational pack-
ets and transported over the LAN or WAN.
D-2
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: SNMP
SNMP Embedded Agent
The Router Option Module supports the following groups from
MIB-II (RFC 1213):
• System Group
• UDP Group
• Interfaces Group
• ICMP Group
• Address Translation Group
• IP Group
• TCP Group
Also, the Ethernet transmission MIB is supported (RFC 1643).
The following manager requests are supported:
• Get object
• Get next object
• Set object
Communities
The Router Option Module permits up to eight communities to be
defined. The privilege level of each community can be set. The de-
fault community is public with read-only privileges. When the IP
address is all zeros, any manager of the community can access the
Router Option Module.
Traps
Up to four hosts can be set to receive traps. Each host entry re-
quires an IP address of the manager.
61203.153L2-1
Router Option Module User Guide
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: SNMP
D-4
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal Mode
Commands
Appendix E
The Router Option Module supports a command line interface.
All menu options are configurable and readable from the terminal
mode. Additional commands are also available.
MENU COMMANDS
Every menu item in the menu structure can be accessed through
the terminal mode interface. Terminal commands are as follows:
top_menu sub_menu1 sub_menu2 … config_item
Each config_item is entered as shown below.
Type:
Entered As:
string
printable characters within double quotes
printable characters within double quotes
xx.xx.xx.xx (0..9) separated by ‘.’
xx:xx:xx:xx (0..9,a..f) separated by ‘:’
sub-string or [#index]
password
IP address
Hex
enum
unsigned
date
digits (0..9)
mm-dd-yyyy
time
hh:mm:ss
date/time
activator
list
mm-dd-yyyy hh:mm:ss
read only
followed by index with first record being 1
followed by index with first record being 1
array
61200350L1-1
Router Option Module User Guide
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: Terminal Mode Commands
Key Words
One of the following key words must be used first:
Key Word
info
Goes directly to the following menu . . .
Configuration/System Info
Configuration/IP
ip
ipx
Configuration/IPX
bridge
security
ppp
Configuration/Bridge
Configuration/Security
Configuration/PPP Profile
Configuration/Management/Telnet
Configuration/Management/SNMP
Configuration/Management/Maint
Configuration/Status
telnet
snmp
maint
status
test
Configuration/Test
logs
Configuration/Logs
util
Configuration/Utilities
frame
Configuration/WAN/Frame Relay
For Example:
What it is . . .
What it does . . .
Telnet user 1 name “guest” Sets user name for telnet user list
entry 1 to “guest”
Test 2047
Starts 2047 test
Status ip 1 gateway
Returns the gateway address for IP
route table entry 1
E-2
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: Terminal Mode Commands
Additional Commands
Other commands available from the terminal mode are given be-
low:
Command
Description
save
Saves the configuration to non-volatile RAM
(flash).
mac
Returns the MAC address for the Router Option
Module.
version
Returns the firmware version and routing stack
version.
reset
Resets the unit.
exit
Leaves terminal mode and returns to menus.
download
Downloads complete configuration to the termi-
nal screen for capture.
Download/Uploading Configuration
The Router Option Module’s configuration can be captured to a
text file using the download command. The text file can be edited
if required.
Uploading the configuration can be accomplished by sending the
text file to the Router Option Module in terminal mode. A baud
rate of 9600 is strongly recommended when uploading. As soon as
the upload has been completed, type Save to save the new config-
uration to flash.
A reset command or power up cycle 10 seconds after the save
command is recommended to ensure that the new configuration
is complete.
61203.153L2-1
Router Option Module User Guide
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: Terminal Mode Commands
E-4
Router Option Module User Guide
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
bridge table 5-5
bridge/address table 4-18
bridge/mode 4-13, 4-40
bridge/spanning tree 4-15
address table 4-18
address table/aging 4-18
address table/forward policy 4-18
ADTRAN Equipment Warranty 1-4
ADTRAN Shipments Include 2-1
ADTRAN Web 2-1
bridge/WAN IP bridge 4-14
bridge/WAN IPX bridge 4-14
bridging 1-2
concurrent routing and bridging 1-3
demand 1-2
ADTRAN Web page 2-1
Adtran Web Page 2-1
agent D-1, D-3
ARP cache 5-4
authentication 4-19, 4-35
with Express XL/XLT as authentica-
tor 4-35
authentication/Rx password 4-36
authentication/Rx username 4-36
authentication/Tx method 4-36
authentication/Tx password 4-36
authentication/Tx username 4-36
C
call log 6-4
call log messages C-5
call log/active 6-4
call log/level 6-4
call log/view 6-4
call log/wrap 6-4
CHAP 4-21, 4-36
command line interface E-1
command prompt mode 4-48
commands E-3
B
communities D-3
baud rate 4-47
communities/manager IP 4-46
communities/name 4-46
communities/privilege 4-46
concurrent routing and bridging 1-3
configuration
bridge 4-40
bridge group 1 4-17
bridge group 1/active 4-17
bridge group 1/path cost 4-17
bridge group 1/priority 4-17
bridge group 2/active 4-17
bridge group 2/path cost 4-17
bridge group 2/priority 4-17
bridge map/active 4-32
bridge map/bridge group 4-32
bridge menu 4-13
downloading/uploading E-3
configuration menu 3-2, 4-1
configuration/bridge 4-13
configuration/IP 4-4
configuration/IPX 4-10
configuration/management 4-44
configuration/management menu 4-44
configuration/PPP profile 4-35
bridge mode 1-2
61200350L1-1
Router Option Module User Manual
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
configuration/security 4-19
configuration/system info 4-1
configuration/terminal mode 4-48
configuration/WAN 4-3
filter defines 4-22
filter defines /IP filter defines 4-23
filter defines /IPX filter defines 4-24
filter defines /MAC filter defines 4-22
filter defines /pattern filter defines 4-23
filters 4-41
D
filters/in exceptions 4-42
filters/LAN-to-WAN (out) 4-43
filters/out exceptions 4-43
filters/WAN-to-LAN (in) 4-41
firmware revision 4-2
data bits 4-47
date/time 4-2
default gateway 4-4
demand bridging 1-2
DHCP mode 4-7
forward delay 4-16
display B-1
frame relay 1-2
DLCI mapping 4-27
DLCI mapping/active 4-29
DLCI mapping/bridge map 4-32
DLCI mapping/DLCI 4-29
DLCI mapping/IP map 4-29
DLCI mapping/IPX map 4-31
DLCI table 5-3
frame relay/DLCI mapping 4-27
frame relay/maintenance protocol 4-27
frame relay/polling frequency 4-27
frame type 4-11
front panel operation 3-1
G
DNS 4-8
DNS server 4-8
GetNextRequest D-2
DNS/domain name 4-8
DNS/server 1 4-8
H
DNS/server 2 4-8
domain name 4-8
hello time 4-16
download/uploading configuration E-3
I
E
interface
Ethernet B-1
EAP 4-21, 4-36
IP filter defines 4-23
IP map/active 4-29
IP map/far-end IP address 4-29
IP map/IARP 4-29
IP map/IP netmask 4-29
IP map/link IP address 4-30
IP map/RIP method 4-30
IP map/RIP protocol 4-30
IP menu 4-4
echo request 6-1
embedded agent D-3
environmental specifications B-1
Ethernet interface (LAN) B-1
F
factory default 1-2
filter
setting up 4-22
IP router 1-1, 4-6
Index-2
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
IP router/mode 4-6
IP routes 5-5
LAN port/active 4-16
LAN port/path cost 4-16
LAN port/priority 4-17
LAN stats 5-9
IP routing 1-2
IP stats 5-10
IP/default gateway 4-4
IP/DNS 4-8
IP/IP address 4-4
IP/IP router 4-6
IP/mode 4-37
IP/NAT 4-7, 4-37
IP/proxy ARP 4-9
IP/RIP 4-6, 4-38
IP/route 4-37
list of items 2-1
Local and Remote Configuration 4-1
local and remote configuration for NxIQ
4-1
logs menu 3-3, 6-2
logs/call log 6-4
logs/network log 6-4
logs/PPP log 6-3
logs/sys log host 6-3
IP/static routes 4-5
IP/subnet mask 4-4
IP/UDP relay 4-8
IPX filter defines 4-24
IPX map/active 4-31
IPX map/IARP 4-31
IPX map/link network 4-31
IPX menu 4-10
M
MAC addresses 1-1
MAC bridging 1-2
MAC filter defines 4-22
maint port/baud rate 4-47
maint port/data bits 4-47
maint port/parity 4-47
maint port/password 4-47
maint port/password protect 4-47
maint port/stop bits 4-48
maintenance port 4-47
maintenance protocol 4-27
management 4-44
IPX router 1-1
IPX routes 5-7
IPX routing 1-3
IPX servers 5-8
IPX/frame type 4-11
IPX/mode 4-10, 4-39
IPX/network 4-10
IPX/remote network 4-39
IPX/RIP timer 4-12
IPX/SAP timer 4-12
IPX/seed status 4-11
IPX/triggered 4-39
IPX/type 20 packets 4-39
management/maint port 4-47
management/SNMP 4-45
management/Telnet 4-44
maximum age 4-16
menu commands E-1
menu structure 3-1
MIB D-2
mode 1-2
L
N
L2 protocol 4-3
LAN bridge 1-1
LAN port 4-16
NAT 1-2, 4-7, 4-8
NAT mode 1-3
61200350L1-1
Router Option Module User Manual
Index-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
NAT/DHCP mode 4-7
NAT/DHCP renewal time 4-7
NAT/web server 4-7
network device
GetResponse D-2
network log 6-4
PPP log/clear 6-3
PPP log/level 6-3
PPP log/view 6-3
PPP log/wrap 6-3
PPP peer 4-8
PPP profile 4-19, 4-35
PPP profile/authentication 4-35
PPP profile/bridge 4-40
PPP profile/filters 4-41
PPP profile/IP 4-36
PPP profile/IPX 4-39
PPP profile/PPP 4-40
PPP/max config 4-41
PPP/max failure 4-41
PPP/max timer 4-41
PPP/VJ compression 4-40
proxy ARP 4-9
network log messages C-6
network log/active 6-4
network log/clear 6-5
network log/level 6-5
network log/view 6-5
network log/wrap 6-5
network manager D-1
GetRequest D-2
none 4-6
NxIQ 4-1
NxIQ Front Panel Menu Structure 3-9
O
R
operation, front panel 3-1
Radius 4-19, 4-45
Radius server 4-19
P
radius server/primary server 4-20
radius server/retry count 4-20
radius server/secondary server 4-20
radius server/secret 4-20
radius server/UDP port 4-20
Receipt Inspection 2-1
Repair Policy 1-4
packets
filtering 4-22
PAP 4-21, 4-36
parity 4-47
password 4-47
pattern filter defines 4-23
physical specifications B-1
pin assignments for NxIQ and ESP ether-
net card connectors A-1
ping 7-2
RIP 1-1, 1-3, 4-6, 4-38
RIP timer 4-12
RIP/direction 4-6, 4-38
RIP/method 4-6, 4-38
RIP/mode 4-6, 4-38
RIP/protocol 4-6, 4-38
RIP/triggered 4-39
poison reverse 4-6, 4-38
polling frequency 4-27
power requirements B-1
PPP 1-2, 4-21, 4-40
PPP log 6-3
PPP log messages C-1
PPP log/active 6-3
RIP/V2 secret 4-7
RMA 1-4
route/force IP 4-37
route/IP/net 4-37
Index-4
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
route/netmask 4-37
physical B-1
routing
split horizon 4-6, 4-38
static routes/active 4-5
static routes/gateway 4-5
static routes/hops 4-5
static routes/IP address 4-5
static routes/private 4-5
static routes/subnet mask 4-5
status menu 3-3, 5-1
status/ARP cache 5-4
status/bridge table 5-5
status/IP routes 5-5
status/IP stats 5-10
status/IPX routes 5-7
status/IPX servers 5-8
status/LAN stats 5-9
status/sessions 5-2
concurrent routing and bridging 1-3
IP 1-2
IPX 1-3
Rx only 4-6
S
SAP 1-1, 1-3
SAP timer 4-12
security levels 3-8
security menu 4-19
security/authentication 4-19
security/filter defines 4-22
security/PPP 4-21
security/radius server 4-19
seed status 4-11
Service 1-4
sessions 5-2
sessions/DLCI table 5-3
sessions/PPP session 5-2
sessions/spanning tree 5-4
SetRequest D-2
shipping damage 2-1
SNMP 4-45, D-1
SNMP access 4-46
SNMP/communities 4-46
SNMP/traps 4-46
spanning tree 4-15, 5-4
spanning tree algorithm 1-1, 1-2, 4-15
spanning tree/bridge group 1 4-17
spanning tree/bridge group 2 4-17
spanning tree/forward delay 4-16
spanning tree/hello time 4-16
spanning tree/LAN port 4-16
spanning tree/maximum age 4-16
spanning tree/mode 4-15
spanning tree/priority 4-16
specifications
status/WAN stats 5-8
stop bits 4-48
subnet mask 4-4
system contact 4-2
system info menu 4-1
system location 4-2
system mame 4-2
system uptime 4-2
T
Telnet 4-44
Telnet client 7-2
Telnet/server access 4-44
Telnet/user list 4-44
terminal menu
navigating 3-4
top level 3-2
terminal mode 4-48
test menu 3-3
test menu/2047 loopback 6-2
test menu/echo request 6-1
TFTP 7-3
environmental B-1
61200350L1-1
Router Option Module User Manual
Index-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
TFTP host 7-3
utilities/upgrade menu 7-2
transfer methods 7-3
Trap D-2
V
traps D-3
VJ compression 4-40
traps/manager IP 4-46
traps/manager name 4-46
Tx and Rx 4-6
W
Tx methods 4-36
Tx only 4-6
type 20 packets 4-39
WAN IP bridge 4-14
WAN IP bridge proxy ARP 4-14
WAN IP bridge/netmask 4-14
WAN IP bridge/network 4-14
WAN IP bridge/triggered 4-14
WAN IPX bridge 4-14
U
UDP port type 4-9
WAN IPX bridge/frame type 4-15
WAN IPX bridge/network 4-15
WAN IPX bridge/seed status 4-15
WAN IPX bridge/triggered 4-15
WAN stats 5-8
UDP relay 4-8
UDP relay list 4-9
UDP relay list/relay address 4-9
UDP relay list/UDP port type 4-9
UDP relay list/UDP ports 1, 2, 3 4-9
UDP relay/mode 4-8
WAN/L2 protocol 4-3
www.adtran.com 2-1
UDP relay/UDP relay list 4-9
upgrade menu 7-2
www.adtran.com. 2-1
upgrade/abort transfer 7-4
upgrade/filename 7-3
upgrade/start transfer 7-3
upgrade/status 7-3
X
xmodem 7-3
upgrade/TFTP host 7-3
upgrade/TFTP server 7-4
upgrade/transfer method 7-3
user list 4-44
user list/authen method 4-45
User List/Idle Time 4-45
user list/level 4-45
user list/name 4-45
user list/password 4-45
using keyboard to navigate menu 3-5
utilities menu 3-3, 7-1
utilities/exit 7-4
utilities/ping 7-2
utilities/Telnet client 7-2
Index-6
Router Option Module User Manual
61200350L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Support Information
Presales Inquiries and Applications Support
Please contact your local distributor, ADTRAN Applications Engineering, or ADTRAN
Sales:
Applications Engineering
Sales
(800) 615-1176
(800) 827-0807
Post-Sale Support
Please contact your local distributor first. If your local distributor cannot help, please con-
tact ADTRAN Technical Support and have the unit serial number available.
Technical Support
(888) 4ADTRAN
Repair and Return
If ADTRAN Technical Support determines that a repair is needed, Technical Support will
coordinate with the Customer and Product Service (CaPS) department to issue an RMA
number. For information regarding equipment currently in house or possible fees associ-
ated with repair, contact CaPS directly at the following number:
CaPS Department
(256) 963-8722
Identify the CaPS number clearly on the package (below address), and return to the follow-
ing address:
ADTRAN Customer and Product Service
6767 Old Madison Pike
Progress Center
Building #6 Suite 690
Huntsville, Alabama 35807
RMA # _____________
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|