ADTRAN Network Card T1 FT1 User Manual

For more detailed documentation, visit us online at www.adtran.com.  
®
NetVanta T1/FT1 + DSX-1 Network Interface Module (NIM) P/N 1202863L1  
Quick Start Guide  
INSTALLATION INSTRUCTIONS  
1. Remove the power from the unit.  
WAN-T1  
DSX-1  
DBU  
2. Slide the option module into the option slot until the module is  
firmly seated against the chassis.  
3. Secure the pins at both edges of the module.  
4. Connect the cables to the associated device(s).  
5. Complete installation of the base unit.  
6. Restore power to the unit.  
SPECIFICATIONS  
Operating  
Frame Relay, Multilink Frame Relay,  
Modes  
T1/FT1  
Interface  
PPP, Multilink PPP, HDLC  
For NetVanta modules with outside plant  
connections, ensure that all cables are removed  
from the module before installing or removing it  
from the NetVanta chassis.  
Supported Standards: AT&T TR 62411, AT&T TR 54016,  
Bellcore TR.194, ANSI T1.403  
Line Rate: 1.544 Mbps ±75 bps  
Line Code: AMI or B8ZS  
Framing: D4 (SF) or ESF  
FT1 Line Rate: DS0 channelized (multiples of 56/64 kbps)  
Input Signal: 0 to -36 dB (DS1)  
Line Build-Out: 0, -7.5, -15, -22.5 dB (long), 0 to 655 ft  
(short)  
NetVanta modules should be installed only in NetVanta  
Series products.  
Connector: RJ-48C  
DS0 Assignment: Programmable  
Supported Standards: ANSI T1.102  
Line Rate: 1.544 Mbps  
DSX Receiver Input Range: -10 dBdsx to +6 dBdsx  
Capacity: 1 to 24 DS0s  
Line Codes: AMI, B8ZS  
DSX-1 interface to PBX  
Framing: D4 (SF) or ESF  
Line Length: 0 to 655 ft and -7.5 dB  
Connector: RJ-48C  
WAN-T1 NETWORK (RJ-48C) CONNECTION PINOUTS  
DSX-1  
Interface  
Pin  
Name  
R1  
T1  
Description  
1
Receive data from the network - Ring 1  
Receive data from the network - Tip 1  
Unused  
2
3
4
R
Transmit data toward the network - Ring  
Transmit data toward the network - Tip  
Unused  
5
T
6-8  
Clock Source Network, internal, and through  
DSX-1 (RJ-48C) CONNECTION PINOUTS  
Test Pattern Generation and Detection: QRSS, 511, 215 - 1,  
Diagnostics  
Pin  
Name  
Description  
220 - 1, all ones, all zeros  
Network loopbacks (local and remote); responds to both  
inband and FDL loop codes (T1 interface only)  
Alarm generation and detection  
Network and user sets of performance data (15 minutes  
and 24 hours)  
1
R
Transmit data toward the DTE- Ring  
Transmit data toward the DTE - Tip  
Unused  
2
T
3
4
R1  
T1  
Receive data from the DTE - Ring 1  
Receive data from the DTE - Tip 1  
Unused  
5
6-8  
Compliance  
Physical  
FCC Part 15 Class A, EN 55022 Class A  
ACTA/FCC Part 68, IC CS-03  
UL/CUL 60950  
Dimensions: 2.75-inch W x 4.25-inch D  
Operating Temperature: 0°C to 50°C  
Storage Temperature: -20°C to 70°C  
Relative Humidity: Up to 95 percent, noncondensing  
An optional Dial Backup Interface Module (DIM) is  
required for dial backup applications.  
For a description of the DBU pinouts, refer to the Quick  
Start Guide included with your DIM shipment.  
Quick Start Guide, 61202863L1-13D, November 2006  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Copyright © 2006 ADTRAN, All Rights Reserved  

Acer Computer Monitor AL2023 User Manual
Adcom Stereo Amplifier GFA 7300 User Manual
Advantech Personal Computer PPC 120 User Manual
AEG Juicer ESF 1031 User Manual
Aiphone Intercom System IS Series User Manual
AKG Acoustics Microphone C 419 User Manual
Alto Shaam Oven 714ESG Over User Manual
Behringer Microphone T 1 User Manual
Beko Dishwasher DFS1530 User Manual
Beko Range CSM 89300 G User Manual