ADC Network Card UTU 701C User Manual

WorldDSL  
USER MANUAL  
RATE SELECTABLE HDSL  
LINE AND DESKTOP UNITS  
UTU-701C List 1  
HDSL  
Universal Termination Unit  
Part Number: 150-1422-01C  
LPBK  
ETU-751C List 1  
ETSI Termination Unit  
Part Number: 150-1432-01C  
WorldDSL  
L
S
G.703  
D
H
C
N
Y
S
I/F  
M
L
A
C
K
B
O
L
P
L
M
L
A
M
E
R
4
2
.
V
H
D
S
L
Download from Www.Somanuals.com. All Manuals Search And Download.  
700-701-100-02  
Using This Manual  
USING THIS MANUAL  
The following conventions are used in this manual:  
Monospace typeindicates screen text.  
Keys you press are indicated by small icons such as Y or ENTER . Key combinations to be pressed  
simultaneously are indicated with a plus sign as follows: CTRL + ESC .  
Items you select are in bold.  
Three types of messages, identified by icons, appear in text.  
Notes contain information about special circumstances.  
Cautions indicate the possibility of personal injury or equipment damage.  
The Electrostatic Discharge (ESD) symbol indicates that a device or assembly is susceptible to  
damage from electrostatic discharge.  
For a list of abbreviations used in this document, refer to “Abbreviations” on page 70.  
INSPECTING SHIPMENT  
Upon receipt of the equipment:  
Unpack each container and inspect the contents for signs of damage. If the equipment has been damaged in  
transit, immediately report the extent of damage to the transportation company and to ADC DSL Systems,  
Inc. Order replacement equipment, if necessary.  
Check the packing list to ensure complete and accurate shipment of each listed item. If the shipment is short  
or irregular, contact ADC DSL Systems, Inc. as described in “Product Support” on page 69. If you must store  
the equipment for a prolonged period, store the equipment in its original container.  
ETU-701C and ETU-751C List 1  
August 9, 2002  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Inspecting Shipment  
700-701-100-02  
iv  
August 9, 2002  
ETU-701C and ETU-751C List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700-701-100-02  
Table of Contents  
TABLE OF CONTENTS  
ETU-701C and ETU-751C List 1  
August 9, 2002  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
700-701-100-02  
LTU and NTU Interface Performance History Screens.................................................... 53  
vi  
August 9, 2002  
ETU-701C and ETU-751C List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700-701-100-02  
List of Figures  
LIST OF FIGURES  
1. Leased Line Data Application on a Single-pair G.703 Network....................................................................3  
2. UTU-701C Line Unit Front Panel ..................................................................................................................4  
3. ETU-751C Desktop Unit Front Panel.............................................................................................................4  
4. ETU-751C Desktop Unit Rear Panel..............................................................................................................7  
5. Line and Desktop Unit Functional Block Diagram ......................................................................................11  
6. Typical Structured Mode Application...........................................................................................................14  
7. Unstructured Mode Application....................................................................................................................16  
8. Loopback Operations....................................................................................................................................19  
9. Installing the UTU-701C Line Unit..............................................................................................................23  
10. UTU/ETU Console Port and Maintenance Terminal Connector Pinouts.....................................................25  
11. Connecting a Maintenance Terminal to a Line Unit.....................................................................................26  
12. Logon Password Screen................................................................................................................................27  
13. Console Screen Menu Bar.............................................................................................................................27  
14. Console Screen Menu Structure....................................................................................................................28  
15. Items in Console Screen Status Bar..............................................................................................................30  
16. Console Screen Config Menu .......................................................................................................................32  
17. Config Terminal Settings Menu....................................................................................................................33  
18. Config Date and Time Menu ........................................................................................................................34  
19. Config Change Password Menu....................................................................................................................35  
20. Config Circuit ID Menu................................................................................................................................36  
21. Config System Settings Menu.......................................................................................................................37  
22. Config LTU Interface Menu with Unstructured Mode Data Rate................................................................39  
23. Config NTU Interface Menu with Structured Mode Data Rate....................................................................39  
24. Config Alarms Menu ....................................................................................................................................41  
25. Config Alarms LTU Interface Menu ............................................................................................................42  
26. Config Alarms NTU Interface Menu............................................................................................................42  
27. Config Alarms HDSL Span 1 Menu.............................................................................................................43  
28. Set to Factory Defaults Screen......................................................................................................................44  
29. Main Console Screen ....................................................................................................................................46  
30. Monitor Menu ...............................................................................................................................................48  
31. Monitor LTU Interface Screen......................................................................................................................49  
32. Monitor NTU Interface Screen .....................................................................................................................50  
33. Monitor HDSL Span 1 Screen ......................................................................................................................51  
34. History Menu ................................................................................................................................................52  
35. History LTU Interface Menu ........................................................................................................................53  
36. History NTU Interface Menu........................................................................................................................53  
ETU-701C and ETU-751C List 1  
August 9, 2002  
vii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Figures  
700-701-100-02  
37. LTU Interface Alarm History Screen........................................................................................................... 54  
38. History HDSL Span 1 Menu ........................................................................................................................ 55  
39. 24 Hour History Screen for HDSL Span 1................................................................................................... 55  
40. 7 Day History Status Screen for HDSL Span 1............................................................................................ 56  
41. Alarm History Status Screen for HDSL Span 1........................................................................................... 57  
42. Inventory Screen........................................................................................................................................... 58  
43. Test Menu Screen......................................................................................................................................... 60  
44. ETSI Firmware Download Utility Menu...................................................................................................... 62  
47. ECA-802 DB9M to RJ-45 Connector Adapter, Part Number 150-1472-01 ................................................ 67  
viii  
August 9, 2002  
ETU-701C and ETU-751C List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700-701-100-02  
List of Tables  
LIST OF TABLES  
1. Rate Selectable G.703 Unit Characteristics....................................................................................................2  
2. Transmission Ranges with 0 db ETSI Noise ..................................................................................................3  
3. Line and Desktop Unit Front Panel Components ...........................................................................................5  
4. Line and Desktop Unit Front Panel LED Indications.....................................................................................6  
5. ETU-751C Desktop Unit Rear-Panel Components ........................................................................................7  
6. WorldDSL Product Compatibility ..................................................................................................................8  
7. Typical Structured Mode System Settings....................................................................................................15  
8. Typical Unstructured Mode System Settings................................................................................................16  
9. Examples of Selected and Actual HDSL Payload Rates ..............................................................................17  
10. Monitored HDSL Transmission and Interface Performance Parameters......................................................18  
11. HDSL Transmission and Application Interface Alarms...............................................................................19  
12. Loopbacks Selected at Front Panel Pushbuttons and Console Screens ........................................................20  
13. Loopback Equivalents...................................................................................................................................21  
14. Console Screen Menus..................................................................................................................................29  
15. Console Screen Status Bar Displays.............................................................................................................30  
16. Console Screen Navigation Keys..................................................................................................................31  
17. Config Menu Options and Recommended Order of System Configuration.................................................32  
18. Fields and Options Displayed in Config System Settings Menu..................................................................38  
19. Fields and Options in Displayed Config LTU and Config NTU Interface Menus.......................................40  
20. Fields Displayed in Config Alarms LTU and Config Alarms NTU Interface Menus..................................43  
21. Fields Displayed in Config Alarms HDSL Span 1 Menu.............................................................................44  
22. Factory Default System Settings...................................................................................................................45  
23. Reading the Main Console Screen................................................................................................................46  
24. Fields Displayed in Main Console Screen....................................................................................................47  
25. Fields Displayed in Monitor LTU and Monitor NTU Interface Screens......................................................49  
26. Fields in Monitor HDSL Span 1 Screen .......................................................................................................51  
27. LTU Interface and NTU Interface Alarm History Data................................................................................54  
28. HDSL Span Alarm History Data ..................................................................................................................57  
29. Inventory Screen Data...................................................................................................................................59  
30. Test Menu Options........................................................................................................................................61  
31. BER Section of Test Menu ...........................................................................................................................61  
32. ETSI Firmware User Selectable Download Menu Options..........................................................................63  
33. Navigating the ETSI Firmware Download Menu.........................................................................................63  
34. D9F HDSL Line Connector Pinouts.............................................................................................................64  
35. D25F Data Port Connector Pinouts...............................................................................................................64  
36. ECA-800 DB25M to M34F (V.35) Connector Adapter Pinouts ..................................................................65  
ETU-701C and ETU-751C List 1  
August 9, 2002  
ix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Tables  
700-701-100-02  
37. ECA-801 DB25M to DB15F (X.21) Connector Adapter Pinouts................................................................ 66  
38. ECA-802 DB9M to RJ-45 Connector Adapter Pinouts ............................................................................... 67  
x
August 9, 2002  
ETU-701C and ETU-751C List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700-701-100-02  
Overview  
OVERVIEW  
ADC® WorldDSLoffers High-bit-rate Digital Subscriber Line (HDSL) Line Termination Units (LTUs),  
Network Termination Units (NTUs), Universal Termination Units (UTUs), and ETSI Termination Units (ETUs).  
The units are shelf and enclosure mounted, providing full-duplex transmission of up to 2.048 Mbps data over  
one or two twisted pairs of copper wire. Public carriers and private network providers can use these units to offer  
low-cost service with fiber-optic quality using the local copper loop without installing repeaters or conditioning  
the outside plant. The units are used in systems that comply with European Telecommunication Standards Institute  
(ETSI) specification TS 101 135.  
This practice describes the WorldDSL RS UTU-701C List 1 and ETU-751C List 1 Rate Selectable HDSL line and  
desktop units. The terms for these units are defined as follows:  
LTU and NTU are defined by ETSI to distinguish between the two units in an HDSL system. An LTU is  
generally located at the Exchange Office end of the circuit and acts as the master unit. The NTU is located at  
the customer site and acts as the slave unit.  
UTU is defined by ADC. These are programmable HDSL line units that can be configured as an  
LTU (master) or an NTU (slave). The UTU default configuration is NTU (slave). The UTUs do not provide  
line power to other HDSL units. All other aspects of UTU functionality are identical to LTUs or NTUs. The  
UTU-701C has a G.703 interface and must be locally powered from a -36 Vdc to -72 Vdc power supply.  
ETU is defined by ADC. These are programmable HDSL line units housed in plastic enclosures with interface  
and power connectors for convenient use as integrated desktop units. The ETUs can be configured as an LTU  
or an NTU. The ETU default configuration is NTU. The ETU-751C does not provide or receive line power;  
it must be locally powered. All other aspects of ETU functionality are identical to LTUs or NTUs. The  
ETU-751C has a G.703 interface and contains a power supply that accepts 100 to 240 volt, 50 or 60 Hz,  
AC power.  
WorldDSL RS (rate selectable) is defined by ADC. WorldDSL RS is a single pair High-bit-rate Digital  
Subscriber Line (HDSL) solution that offers extended reach capabilities through the use of industry-leading  
multi-rate DSL technology. The UTU-701C and ETU-751C deploy HDSL in networks using a single pair of  
copper wire running at speeds between 256 kbps and 2048 kbps. The HDSL payload rates are menu selected  
in time slot increments of 64 kbps, ranging from 256 kbps to 2048 kbps. Transmission ranges vary according  
to the rate selected. Depending on noise environment, ranges of up to 7.1 km (4.4 miles) are possible at the  
lowest-selectable HDSL payload rate (256 kbps) using 0.51 mm wire. Longer ranges are possible with larger  
wire.  
These HDSL units are configured as Data Communications Equipment (DCE) and respond to data, clock, and  
control signals from Data Terminal Equipment (DTE).  
Use of this product in a manner other than defined in this technical practice may cause  
equipment damage or injury to personnel.  
Gebrauch dieses Produkts in einer Weise anders als definiert kann in dieser technischen Praxis  
Geräte Schaden oder Verletzung zu Personal verursachen.  
RATE SELECTABLE HDSL UNIT FIRMWARE  
Version 4.01 is the current release for the rate selectable HDSL unit firmware. This firmware must be installed at  
each end of the circuit (that is, in both the LTU and NTU).  
WorldDSL RS units are not backward compatible with standard HDSL or management unit  
firmware. The installed firmware must be that designed for RS units.  
RS G.703 LTUs can communicate with RS Nx64k NTUs, but only if HDSL unit firmware  
Version 4.01 or later is installed at each end of the circuit.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Overview  
700-701-100-02  
EMU FIRMWARE COMPATIBILITY  
The EMU-830 Management Unit firmware must be Version 3.22.08 or later to support rate selectable HDSL units.  
APPLICATION INTERFACE  
The UTU-701C and ETU-751C provide G.703 interface ports with a rate selectable HDSL payload. The only  
application mode is Single, indicating single pair.  
The G.703 E1 application interface conforms with the ITU-T G.703 physical specification and can be configured  
for an impedance of 75 unbalanced or 120 balanced. User data can be unstructured or structured according to  
the G.704 framing standard, and optionally CRC-4 multiframed according to the G.706 standard. Structured mode  
is automatically invoked when 1 to 29 time slots are selected. Unstructured mode is invoked when 30, 31, or 32  
time slots are selected.  
The exchange office data terminal equipment (DTE) allocates the 2048 kbps E1 payload to the G.703 port in  
time-slot increments of 64 kbps each. The number of G.703 time slots allocated by the DTE is determined by the  
selected HDSL payload rate (the DTE and HDSL payloads must be set to the same rate). Time slots not allocated  
to the G.703 port are replaced by idle codes at the G.703 output.  
The UTU-701C and ETU-751C have HDSL payload rates ranging from 256 kbps to 2048 kbps. The desired  
HDSL payload rate is selected in time slot increments of 64 kbps from the system settings menu of the  
LTU-configured unit. The selected payload rate applies to both the receive and transmit directions. The  
LTU-configured unit automatically configures the NTU-configured unit for the same payload rate. Table 1 lists  
the characteristics of the rate selectable G.703 line and desktop units covered in this practice.  
Table 1. Rate Selectable G.703 Unit Characteristics  
User Selected  
HDSL Payload  
Rates (kbps)  
Actual  
HDSL Payload  
Rates (kbps)  
LTU/NTU  
Configurable  
Model  
Interface  
UTU-701C  
ETU-751C  
G.703  
G.703  
64 to 2048  
64 to 2048  
256 to 2048  
256 to 2048  
Yes  
Yes  
The G.703 units always transmit time slots 0 and 16, which results in 128 kbps being added to the user-selected  
HDSL payload rate (when 1 to 30 time slots are selected). For example, the lowest-selectable HDSL rates, 64 and  
128 kbps, are transmitted at 256 kbps. This 128 kbps increase in payload rate, however, does not affect the rate of  
the G.703 data received at the customer or network DTE.  
Figure 1 shows a single-pair, leased-line data application using 4 time slots for a 256 kbps HDSL payload rate.  
Customer data is input to the remote G.703 port at the 256 kbps rate, transported over the HDSL loop at an  
increased 384 kbps rate, and received by the exchange office DTE at the original 256 kbps rate. For more  
2
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
Overview  
Customer Side  
Network Side  
UTU-701  
(LTU)  
UTU-701  
(NTU)  
Single Pair  
HDSL loop  
Exchange  
Office  
HDSL  
HDSL  
G.703  
DTE  
Time Slots 1 through 4  
+Time Slots 0 and 16  
4 Time Slots  
4 Time Slots  
(256 kbps)  
PC  
Customer  
DTE  
G.703  
(256 kbps)  
(384 kbps)  
Figure 1. Leased Line Data Application on a Single-pair G.703 Network  
HDSL TECHNOLOGY  
HDSL is the core technology for ADC’s WorldDSL line of LTUs, UTUs, and ETUs. Rate selectable HDSL  
enables these units to transmit and receive digital data at various rates over various distances on one twisted pair  
of copper wire. Both outbound and inbound signals are delivered on the same pair of wires by using echo  
cancellation techniques. The transmitted signal is canceled at the receiver by precisely predicting the amount of  
signal echo, then subtracting it from the overall input signal. ADC’s market leading HDSL-based products tolerate  
crosstalk, and operate not only on continuous unobstructed pairs of wires, but also on cables with mixed wire  
gauges and bridged taps.  
TRANSMISSION RANGES  
Transmission ranges assume the presence of noise according to the ETSI model described in TS 101 135. The  
expected Bit Error Rate (BER) using this model is 1x10-7. The transmission ranges in such a noise environment  
at the various HDSL line rates over one twisted-pair of 0.4 mm and 0.51 mm copper wire are listed in Table 2.  
The no noise transmission ranges are listed in “Specifications” on page 9.  
Table 2. Transmission Ranges with 0 db ETSI Noise  
RS G.703 HDSL Payload Rate  
Wire Size and Transmission Range (with 0 dB ETSI Noise)  
User Selected  
HDSL Payload  
Rate (kbps)  
Actual  
0.4mm (26 AWG)  
0.51mm (24 AWG) Single  
Single Twisted-Pair  
Twisted-Pair Copper Wire  
Copper Wire  
HDSL Payload  
Rate (kbps)(a)  
64/128  
256  
384  
4.1 km (13,451 ft.)  
3.6 km (11,811 ft.)  
3.4 km (11,155 ft.)  
3.0 km (9,842 ft.)  
2.6 km (8,530 ft.)  
2.2 km (7,218 ft.)  
2.0 km (6,562 ft.)  
5.1 km (16,730 ft.)  
4.7 km (15,420 ft.)  
4.5 km (14,760 ft.)  
4.2 km (13,779 ft.)  
3.4 km (11,155 ft.)  
2.9 km (9,515 ft.)  
2.4 km (7,874 ft.)  
256  
384  
512  
640  
768  
1024  
1152  
1536  
2048(b)  
1408  
1920/1984/2048  
(b) System operates in unstructured mode when 32 time slots are selected.  
(b) The maximum no-noise transmission range is approximately 7.1 km (4.4 miles). See “Specifications” on page 9.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Overview  
700-701-100-02  
FRONT AND REAR PANEL COMPONENTS  
The line and desktop unit front panels are shown in Figure 2 and Figure 3, respectively. The components on these  
panels are described in Table 3 on page 5 and in Table 4 on page 6.  
The ETU-751C desktop unit rear panel is shown in Figure 4 on page 7. The components on this panel are  
described in Table 5 on page 7. The pinouts for the desktop unit rear panel connectors are listed in Table 34 and  
SYNC  
HDSL  
ALM  
HDSL LEDs  
I/F  
I/F ALM LED  
LPBK  
Loopback LEDs and  
push buttons  
Bar code label  
(located on circuit  
side of line card)  
V.24 (RS-232) console port  
Warranty control  
number label  
UTU-701  
G.703  
Figure 2. UTU-701C Line Unit Front Panel  
Loopback LEDs  
and push buttons  
V.24 (RS-232)  
console port  
HDSL LEDs  
WorldDSL  
HDSL  
G.703  
Unit ID and bar code labels  
(located on bottom of unit)  
ALM I/F LED  
Figure 3. ETU-751C Desktop Unit Front Panel  
4
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
Overview  
Table 3. Line and Desktop Unit Front Panel Components  
Function  
Name  
HDSL SYNC LED  
HDSL ALM LED  
I/F ALM LED  
Displays synchronization state for the HDSL loop.  
Displays alarm state for the HDSL loop.  
Displays alarm state for the G.703 data port.  
Displays local (LOC) loopback state.  
LOC LPBK LED  
LOC LPBK Button  
REM LPBK LED  
REM LPBK Button  
Activates the local HDSL analog loopback.  
Displays remote (REM) loopback state.  
Activates the remote interface loopback.  
V.24 (RS-232) console  
port  
Provides bi-directional communication between the unit and an external maintenance terminal through  
a V.24 (RS-232C) interface to allow configuration and performance monitoring through the console  
screen menus as described in “System Configuration” on page 25. This connector can also be used to  
download new firmware to the line unit’s flash memory as described in “Firmware Download Utility” on  
page 62. This port is configured as DCE (see “Maintenance Terminal Connection” on page 25 for  
pinouts).  
Bar code label (all units)  
Warranty control  
Contains the serial number and part number of the unit, as indicated in both bar code and text format.  
Also contains the configuration number of the unit, as indicated by "CFG: Rnn," where nn is the  
configuration number. For example, CFG: R07 would indicate configuration number 07.  
Indicates the beginning year and month of the line card warranty. Also indicates the line card revision  
number label (UTU-701C) number. For example, a warranty control number of "803R07" would indicate a warranty beginning in  
the year 1998 (8), during the month of March (03), and line card revision number R07.  
Unit ID label (ETU-751C) Identifies the model number, manufacturer, part number, and input voltage range of the ETU. Includes  
the CE mark, certifying that the unit is in compliance with directive EN300 386-2. See “Certification and  
Warranty” on the inside of the back cover.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Overview  
700-701-100-02  
Table 4 defines the system states indicated by the front panel LEDs. When power is applied to the unit, one of the  
LEDs listed in Table 4 will always be on.  
Table 4. Line and Desktop Unit Front Panel LED Indications  
LED  
Mode  
Description  
HDSL SYNC LED  
Steady green  
Slow blinking  
Off  
HDSL loop is ready to transmit and receive data across all spans.  
HDSL loop acquisition is in progress for local span.  
HDSL loop is not configured.  
HDSL ALM LED  
Steady red  
Loss of sync word (LOSW); or the margin is below the set margin  
alarm threshold; or Errored Seconds (ES) count is above  
threshold on any span.  
Pulsing red  
Off  
Pulses for every ES on any span.  
Normal transmit or receive data is in progress.  
I/F ALM LED  
Steady red  
Loss of Signal (LOS) alarm due to loss of G.703 signal or Loss of  
Clock (LOC) alarm due to loss of external clock (when using EXT  
timing).  
LPBK LEDs (a)  
LOC  
REM  
Off  
Steady yellow  
Off  
Local HDSL analog loopback is active.  
No loopbacks are active.  
Off  
Off  
Blinking yellow  
Off  
Local interface loopback is active.  
Steady yellow Remote loopback is active.  
Blinking yellow  
Blinking yellow A loopback away from the local equipment is active.  
(a) The LOC and REM LPBK LEDs are read in unison.  
6
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
700-701-100-02  
Overview  
Figure 4. ETU-751C Desktop Unit Rear Panel  
Table 5. ETU-751C Desktop Unit Rear-Panel Components  
Item  
Description  
D15F 120G.703  
connector  
Connects E1 balanced 120 circuits to the enclosure.  
BNC 75In/Out G.703  
connectors  
Connects E1 unbalanced 75 circuits to the enclosure.  
D9F HDSL line connector  
On/Off switch  
Connects the HDSL pair to the enclosure.  
Rocker switch that allows you to turn the externally applied AC power on or off.  
Accepts female end of three-prong power cord supplying 100-240 Vac at 50-60 Hz.  
Power cord receptacle  
UTU-701 and ETU-751 List 1  
August 9, 2002  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Overview  
700-701-100-02  
WORLDDSL PRODUCT COMPATIBILITY  
The line and desktop units are compatible with the WorldDSL products listed in Table 6.  
Table 6. WorldDSL Product Compatibility  
Model  
Description  
Part Number  
Rate-Selectable HDSL Units  
UTU-702C  
UTU-712C  
UTU-722C  
ETU-752C  
ETU-762C  
ETU-772C  
Rate-selectable HDSL Line Unit, Nx64k Serial Data Interface,  
128 to 2048 kbps HDSL Line Rate  
150-1422-02C  
150-1422-12C  
150-1422-22C  
Rate-selectable HDSL Line Unit, Nx64k Serial Data Interface,  
128 to 768 kbps HDSL Line Rate  
Rate-selectable HDSL Line Unit, Nx64k Serial Data Interface,  
128 to 256 kbps HDSL Line Rate  
Rate-selectable HDSL Desktop Unit, Nx64k Serial Data Interface, 150-1432-02C  
128 to 2048 kbps HDSL Line Rate  
Rate-selectable HDSL Desktop Unit, Nx64k Serial Data Interface, 150-1432-12C  
128 to 768 kbps HDSL Line Rate  
Rate-selectable HDSL Desktop Unit, Nx64k Serial Data Interface, 150-1432-22C  
128 to 256 kbps HDSL Line Rate  
Shelves and Enclosures for UTU-701C  
(a)  
(b)  
EMS-830 List 1  
EMS-830 List 2  
Exchange office management shelf, rear connector access  
Exchange office management shelf, rear connector access  
Single-slot remote enclosure with internal AC power supply  
150-1400-01  
150-1400-11  
150-1411-1x  
(c)  
ERE-811  
(d)  
Connector Adapters for ETU-751C  
ECA-800  
ECA-801  
ECA-802  
ECA-804  
ECA-807  
D25M to M34F connector adapter (V.35)  
D25M to D15F connector adapter (X.21)  
150-1470-01  
150-1471-01  
150-1472-01  
150-1474-01  
150-1477-01  
DB9M to RJ-45 connector adapter (HDSL)  
DB9M to 4-position terminal block connector (HDSL)  
DB25M to DB37F connector adapter (RS-449)  
(a) The EMS-830 List 1 supports protection switching, the EMS-830 List 2 does not.  
(b) The EMS-830 List 2 is CE marked. The EMS-830 List 1 is not, and is intended for use in applications  
where the CE Mark is not required.  
(c) The UTU-701C is CE Marked in the ERE-811 List 5 remote enclosure only.  
(d) The ECA-80x series of connector adapters and their pinouts are listed in Table 36 through Table 39,  
beginning on page 65.  
8
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
Specifications  
SPECIFICATIONS  
HDSL Interface  
Line Code  
2B1Q  
Line Rate (selectable in increments of 64 kbps) Up to 2048 kbps  
Protection  
K.20, K.21  
TS 101 135  
Compliance  
Transmission Ranges ( 200 m):  
Transmission Ranges with 0 dB ETSI Noise  
Transmission Ranges with No Noise  
0.4 mm (26 AWG)  
Single Twisted-Pair  
Copper Wire  
0.51 mm (24 AWG)  
Single Twisted-Pair  
Copper Wire  
0.4 mm (26 AWG)  
Single Twisted-Pair  
Copper Wire  
0.51 mm (24 AWG)  
Single Twisted-Pair  
Copper Wire  
HDSL Line  
Rate (kbps)  
256  
384  
4.1 km (13,451 ft.)  
3.6 km (11,811 ft.)  
3.4 km (11,155 ft.)  
3.0 km (9,842 ft.)  
2.6 km (8,530 ft.)  
2.2 km (7,218 ft.)  
2.0 km (6,562 ft.)  
5.1 km (16,730 ft.)  
4.7 km (15,420 ft.)  
4.5 km (14,760 ft.)  
4.2 km (13,779 ft.)  
3.4 km (11,155 ft.)  
2.9 km (9,515 ft.)  
2.4 km (7,874 ft.)  
5.3 km (17,388 ft.)  
4.7 km (15,420 ft.)  
4.6 km (15,092 ft.)  
4.3 km (14,108 ft.)  
3.7 km (12,139 ft.)  
3.3 km (10,827 ft.)  
3.0 km (9,842 ft.)  
7.1 km (23,294 ft.)  
6.7 km (21,982 ft.)  
6.3 km (20,669 ft.)  
5.9 km (19,357 ft.)  
5.3 km (17,388 ft.)  
4.7 km (15,420 ft.)  
3.2 km (10,499 ft.)  
512  
768  
1152  
1536  
2048  
G.703 Interface  
Unstructured Leased Line  
Structured Leased Line  
Fractional E1  
2.048 Mbps per ETS 300 247 (D2048U)  
2.048 Mbps per ETS 300 419 (D2048S)  
User-selectable DS0 blocking, with user-programmable idle code  
Line Code  
HDB3  
Line Rate  
2.048 Mbps  
Impedance (jumper selectable)  
120 balanced (twisted-pair)  
75 unbalanced (coax)  
CRC-4 mode  
Compliance  
User-selectable CRC-4 detection and generation  
ITU-T G.703, G.704, G.706, G.821, G.823, CTR 12  
Timing  
Clock Source  
G.703 input  
External 2.048 MHz clock (per G.703 par. 10)  
Internal Oscillator  
2.048 MHz 50 ppm  
Performance Monitoring and Diagnostics  
HDSL  
Noise margin, pulse attenuation, ES, UAS  
G.703 Interface  
Major Alarm Relay  
Loopbacks  
ES, SES, UAS per G.821. CRC-4 errored seconds, BPV seconds  
Form-C relay contacts (NO, NC, C). Fail-safe operation  
Local interface loopback, local HDSL loopback (V.54 loop 3),  
remote loopback (V.54 loop 2)  
UTU-701 and ETU-751 List 1  
August 9, 2002  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Specifications  
700-701-100-02  
Alarms  
Can be individually set to Disabled, Minor, or Major (major alarms actuate the LTU or NTU alarm relay)  
E1 Interface  
Loss of Signal (LOS)  
Loss of Framing (LFA)  
Alarm Indication Signal (AIS)  
Remote Alarm Indication (RAI)  
External Clock  
HDSL Loop  
Loss of Clock (LOC)  
Margin, programmable threshold (MAR)  
Errored Seconds, programmable threshold (ES)  
Loss of Sync Word (LOSW)  
History  
E1 and HDSL Interface  
24-Hour (15-minute intervals) and 7-Day (24-hour intervals) for  
ES and UAS  
Alarm  
Time stamp of first and last occurrence, number of occurrences for  
all enabled alarms  
Power Requirements  
UTU-701C  
Local input voltage  
Consumption (typical)  
ETU-751C  
-36 Vdc to -72 Vdc (see note at bottom of page)  
4.5 W  
Local input voltage  
Consumption (typical)  
100 to 240 volt, 50 or 60 Hz, AC power  
4.5 W  
Environmental  
Operating Temperature Range  
Humidity  
0 ° C to +50 ° C (32 °F to 122 °F)  
Up to 95% non-condensing  
Storage Temperature  
Storage Humidity  
-40 °C to +70 °C (-40 °F to 158 °F)  
5% to 95% non-condensing  
Regulatory Approvals  
CE Mark Certification  
EN300 386-2  
10  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700-701-100-02  
Functional Description  
FUNCTIONAL DESCRIPTION  
This section provides a functional description of the line and desktop units, including major components,  
single-pair application mode, alarms, and testing (including monitoring and loopbacks).  
MAJOR COMPONENTS  
The major components of the line and desktop units include:  
G.703 interface (75 or 120 )  
rate selectable HDSL interface (including framing, transceiver, and line interface circuits)  
system timing circuits  
processor  
Figure 5 is a functional block diagram of the line and desktop units.  
100-240V  
50/60 Hz  
AC power  
(ETU-751)  
On-board  
power  
-36V to -72V  
DC power  
(UTU-701)  
supply  
module  
Timing  
circuits  
+5V, +3.3V  
HDSL  
loop  
75 and 120 Ω  
DTE Interface  
G.703  
Interface  
Transceiver  
Line interface  
HDSL framer  
Ext. clock  
from management  
unit (UTU-701 only)  
Control  
Status  
Processor  
Front panel  
control and  
Alarm relay  
(UTU-701 only)  
console interface  
Management unit  
backplane interface  
(UTU-701 only)  
RS-232  
console port  
Figure 5. Line and Desktop Unit Functional Block Diagram  
UTU-701 and ETU-751 List 1  
August 9, 2002  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Functional Description  
700-701-100-02  
G.703 Interface  
The G.703 interface performs the following functions:  
provides a jumper-selectable 75 or 120 DTE interface (see “Installation and Startup” on page 23 for jumper  
locations)  
allocates full or fractional portion of the total 2048 kbps bandwidth to and from the G.703 interface  
frames data according to G.704  
inserts an idle code into unused time slots at the G.703 output  
recovers timing from the received G.703 signal  
monitors multiframe CRC-4 errors in the received G.703 signal  
regenerates multiframe (CRC-4) code at the G.703 output  
regenerates time slot 0 at the G.703 output  
transports time slot 16 transparently between G.703 ports  
The G.703 interface operates in the structured application mode when less than 32 time slots are selected and in  
the unstructured mode when 32 time slots are selected (see “System Configuration” on page 25). These modes are  
HDSL Interface  
The HDSL interface includes the HDSL framer, which performs HDSL multiplexing and demultiplexing;  
a firmware-controlled programmable clock, which sets the HDSL line rate at the interface output; and the  
transceiver and line-interface circuits for the single HDSL pair.  
In the transmit direction, the HDSL framer accepts inputs from the G.703 data port as shown in Figure 5. The data  
is placed on the HDSL pair along with the HDSL overhead bits for presentation to the transceiver. A clock  
representing the selected HDSL line rate is introduced to the transceiver, which outputs data on the single-pair  
HDSL line. In the receive direction, overhead bits are stripped and processed, and time slots are output to the  
G.703 interface.  
Reversals of Tip and Ring wires are automatically detected and accommodated. The Monitor HDSL Span screen  
indicates if the Tip and Ring wires are reversed.  
System Timing Circuits  
The UTU and ETU units can synchronize to any one of the following timing sources:  
G.703: Timing recovered from G.703 input signal  
EXT: External 2.048 MHz reference (available only for UTUs in a shelf with a management unit installed)  
Processor  
This device runs a program which in real-time:  
monitors the HDSL framer performance  
responds to user requests  
maintains a history of system performance  
12  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
700-701-100-02  
Functional Description  
Power Sources  
The line and desktop units receive power from the following sources:  
A shelf-mounted UTU-701C receives power from a local source of -36 Vdc to -72 Vdc.  
An enclosure mounted UTU-701C receives power from a local source of -36 Vdc to -72 Vdc or from the  
enclosure’s built-in AC-to-DC power supply (when provided).  
The ETU-751C desktop unit receives power from a source of 100 to 240 volt, 50 or 60 Hz, AC power.  
Input voltage for the UTU-701C line unit (nominal -48 Vdc, tolerance -36 to -72 Vdc) must be  
supplied by an isolated DC source that complies with TNV or earthed SELV requirements of the  
latest version of IEC 950.  
The single-pair rate selectable HDSL units (local and remote) must be locally powered.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Functional Description  
700-701-100-02  
RATE SELECTABLE APPLICATION MODES AND OPTIONS  
Applications for single-pair rate-selectable HDSL are those that require transport of voice and data at various rates  
over various distances on a single pair of wires. Depending on line noise and the HDSL rate selected, spans of up  
to 7.1 km (4.4 miles) can be deployed without the use of doublers. The HDSL line rate depends on the number of  
time slots selected. The UTU-701C and ETU-751C each have 32 time slots with a bandwidth of from 256 kbps  
to 2048 kbps (1 to 32 time slots selected). Each time slot represents a 64 kbps increment of the available  
bandwidth.  
The available rate selectable application modes and options are:  
single  
structured  
unstructured  
CRC-4  
Single Mode  
Single is the only application mode displayed in the Config System Settings menu. It means the system uses a  
single pair of twisted copper wires to transport data.  
Structured Mode  
When less than 32 time slots are selected, the line and desktop units automatically operate in the structured  
mode (see “G.704 Framing and Rate Selectable HDSL” on page 17). There is no structured mode menu selection.  
In structured mode, data at the G.703 interface is framed according to G.704. This permits fractional allocation of  
the total 2048 kbps bandwidth to and from the G.703 interface, insertion of idle code into unused time slots at the  
G.703 output, and monitoring of the G.703 input for CRC-4 multiframe errors.  
A typical structured mode application is illustrated in Figure 6. The settings for this application are listed in  
Table 7. Time slots 1-15 and 17-25 are transported as telephony voice channels between the G.703 ports of the  
two units. Time slots 26-31 are unused and are set to idle code FF. In structured mode, time slot 1 is the beginning  
time slot; time slot 0 is regenerated at the G.703 output. With the CRC-4 mode enabled, the input G.703 signal is  
monitored for CRC-4 multiframe errors and at the G.703 output, a new CRC-4 code is generated. Time slot 16 is  
transported transparently between G.703 ports and may be used for telephony signaling.  
Figure 6. Typical Structured Mode Application  
14  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
700-701-100-02  
Functional Description  
Table 7. Typical Structured Mode System Settings  
Options  
Setting  
Application Mode  
<32 TS (Structured)  
LTU Interface  
Primary Timing Source  
G.703 Port  
G.703  
CRC-4 Mode  
Enabled  
Idle Code  
FF  
Data Rate / # of TSs  
Beginning TS  
1536 kbps / 24  
1
NTU Interface  
Primary Timing Source  
G.703 Port  
G.703  
CRC-4 Mode  
Enabled  
Idle Code  
FF  
Data Rate / # of TSs  
Beginning TS  
1536 kbps / 24  
1
For applications requiring fractional use of the G.703 port, embedded generation and detection of CRC-4  
information, and A-bit insertion, select less than 32 time slots to invoke the structured mode. In the structured  
mode time slot 0 is regenerated according to G.704 at the output of the G.703 interface port. The following values  
apply:  
The Sa bits are always set to 1.  
The A bit is normally set to 0 at the G.703 output port. It is set to 1 during an active Loss of Signal (LOS),  
Alarm Indicating Signal (AIS), or a Loss of Frame Alignment (LFA) condition, if the alarm associated with  
the respective condition is not disabled (see “Configure LTU and NTU Interfaces” on page 39).  
When CRC-4 mode is disabled, the Si bit is transparently transmitted (that is, unmodified from the HDSL  
input data stream).  
When CRC-4 mode is enabled, the Si bit is set to a new CRC-4 multiframe signal and checksum (according  
to G.706).  
The E-bits are nominally set to 1 and set to 0 for each error in the incoming CRC-4 sub-multiframe.  
Match the CRC-4 mode at each interface to the actual type of data present at that node in the  
system. Otherwise CRC-4 data will not be transparently transmitted in CRC-4 disabled mode.  
Also, non-CRC-4 data generates an LFA alarm in CRC-4 enabled mode.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Functional Description  
700-701-100-02  
Unstructured Mode  
When 32 time slots are selected, the line and desktop units automatically operate in the unstructured mode (see  
“G.704 Framing and Rate Selectable HDSL” on page 17). There is no unstructured menu selection.  
In the unstructured mode:  
There is no G.704 framing.  
Time slot 0 is the beginning time slot, and the data rate is fixed at 2048 kbps.  
A transparent transmission channel is provided between the local and remote units.  
CRC-4 detection and generation are not available, and E1 alarms are limited.  
Any framing, multiframing, and common-channel signals can be transmitted through the HDSL line units in the  
unstructured mode, but the units do not monitor for a loss of framing condition.  
Table 8 lists system settings for 2048 kbps transport of data between a DTE connected to an UTU-701C and a  
DTE connected to an ETU-751C. The settings in Table 8 use the G.703 signal from the UTU-side DTE as the  
primary timing source. Timing at the ETU side is recovered from the received G.703 signal. This application is  
illustrated in Figure 7.  
Table 8. Typical Unstructured Mode System Settings  
Options  
Setting  
Application Mode  
32 TS (Unstructured)  
UTU-701C (LTU) Interface  
Primary Timing Source  
G. 703 Port  
G.703  
CRC Mode  
N/A  
Idle Code  
FF  
Data Rate/# of TSs  
Beginning TS  
2048 / 32 TSs  
0
ETU-751C (NTU) Interface  
Primary Timing Source  
Data Rate / # of TSs  
Beginning TS  
G.703  
2048 / 32 TSs  
0
Customer Side  
Network Side  
ETU-751  
(NTU)  
UTU-701  
(LTU)  
Single Pair  
HDSL loop  
HDSL  
HDSL  
32  
32  
32  
Exchange  
Office  
Time Slots  
Time Slots  
Customer  
DTE  
G.703  
Time Slots  
(2048 kbps)  
G.703  
(2048 kbps)  
(2048 kbps)  
DTE  
Figure 7. Unstructured Mode Application  
16  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
Functional Description  
G.704 Framing and Rate Selectable HDSL  
Time slots 0 and 16 are always transported in accordance with the G.704 framing standard. Although not used by  
G.703 to transport data, the rate-selectable HDSL interface treats time slots 0 and 16 as a 128 kbps increase in the  
HDSL payload rate. For example, when 4 time slots are selected (256 kbps), time slots 0 and 16 are transported  
along with the selected time slots, 1 though 4. This results in an HDSL payload rate of 384 kbps (that is, 256 kbps  
plus the 128 kbps added by time slots 0 and 16). Table 9 lists several examples of selected and actual HDSL  
payload rates.  
In structured mode, time slots 0 and 16 do not contain data and are transparent to the G.703 input. The transmitted  
G.703 data arrives at both the customer and network DTE at the selected HDSL payload rate. This is illustrated  
Table 9. Examples of Selected and Actual HDSL Payload Rates  
SelectedHDSLPayload  
Rate (kbps) / Number of  
Time Slots  
Actual HDSL Payload  
Rate (kbps)  
G.703 Time Slots Transported  
1 (plus 0 and 16)  
64 / 1  
128 / 2  
256  
256  
1 and 2 (plus 0 and16)  
192 / 3  
1 through 3 (plus 0 and16)  
320  
256 / 4  
1 through 4 (plus 0 and16)  
384  
384 / 6  
1 through 6 (plus 0 and16)  
512  
512 / 8  
1 through 8 (plus 0 and16)  
640  
640 / 10  
768 / 12  
896 / 14  
1024 / 16  
1152 / 18  
1536 / 24  
1920 / 30  
1984 / 31  
2048 / 32  
1 through 10 (plus 0 and16)  
768  
1 through 12 (plus 0 and16)  
896  
1 through 14 (plus 0 and16)  
1024  
1152  
1280  
1664  
2048  
2048  
2048  
1 through 15 and 17 (plus 0 and16)  
1 through 15, 17 through 19 (plus 0 and16)  
1 through 15, 17 through 25 (plus 0 and 16)  
1 through 15, 17 through 31 (plus 0 and 16)  
1 through 31 (plus 0)  
(a)  
0 through 31  
(a) The line and desktop units operate in the unstructured mode when 32 time slots are selected.  
HOT SWAPPING  
UTUs can be inserted and removed from any compatible shelf or enclosure with the power turned on. This will  
not cause damage to the units nor will it cause interference to any other HDSL circuits that are operating within  
the same shelf or enclosure.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Functional Description  
700-701-100-02  
PERFORMANCE MONITORING AND HISTORY  
The UTU and ETU units provide extensive real time, non-disruptive monitoring of HDSL transmission  
performance parameters for all units in a circuit. Performance of the user interface ports is also monitored. Current  
cumulative counts of the past 24 hours and historical data in the form of 24-hour history (in 15-minute increments)  
and a 7-day history (in 24-hour increments) are available to assist in identifying problem sources during  
troubleshooting. See “Viewing Status” on page 46 for information on performance screens.  
The monitored parameters are described in Table 10.  
Table 10. Monitored HDSL Transmission and Interface Performance Parameters  
Monitored Parameter  
Description  
HDSL Noise Margin  
A measure of the ratio of signal power to noise power, in decibels (dB), at a receiver point. A value  
of 0 dB means that the predicted transmission BER is equal to 10–7. A value of 6 dB means the  
predicted transmission BER is equal to 10–10. The Main menu status display continuously updates the  
margin value.  
HDSL CRC-6  
A six-bit word in every HDSL frame, representing a calculation based on all the bits in that frame. Any  
mismatch at the receiver, between the received CRC-6 and the one calculated, based on the received  
data in the frame, indicates that one or more bits were received in error. The units use this parameter  
to derive HDSL Errored Seconds (ES).  
HDSL Loss of Sync Word  
(LOSW)  
The unit has detected an error in one or more bits in six consecutive HDSL sync words. TS 101 135  
requires two consecutive sync words to be received without error to clear this condition. A LOSW  
condition generally indicates the loop is down, thus data cannot be transmitted.  
Based on the monitored parameters, the LTU and NTU units derive the following performance parameters:  
HDSL Errored Second (ES) An interval of one second during which at least one CRC-6 error is detected at the incoming HDSL  
port or there is an LOSW condition.  
HDSL Unavailable Second  
(UAS)  
A second during which a loop is down.  
ALARMS  
The UTU and ETU units generate alarms for problem conditions on the HDSL transmission facility and at the  
local application interface. Alarms can be individually enabled or disabled as well as configured as a Major or  
Minor alarms. See “System Configuration” on page 25 to configure alarms. See “Viewing Status” on page 46 to  
view alarm conditions.  
The HDSL transmission and application interface alarms are described in Table 11 on page 19.  
18  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
Functional Description  
Table 11. HDSL Transmission and Application Interface Alarms  
Alarm  
Description  
HDSL Alarms  
HDSL alarms include:  
Margin (MAR)  
Margin has fallen below threshold set for the HDSL interface.  
Errored seconds count has exceeded threshold set for the HDSL interface.  
Errored Seconds (ES)  
Loss of Sync Word  
(LOSW)  
Loss of sync word at the HDSL interface. Remains active during restart, but not a cold start.  
G.703 Alarms  
G.703 alarms include:  
Loss of Signal (LOS)  
Loss of signal at the G.703 input.  
Loss of frame alignment at the G.703 input.  
Loss of Frame Alignment  
(LFA)  
Receive Alarm Indication  
Signal (AIS)  
Remote Alarm Indication  
Signal (RAI)  
Alarm indication signal (unframed all ones) received at the G.703 input.  
Remote alarm indication signal received at the G.703 input (through A-bit).  
Loss of Clock (LOC)  
Applies to loss of external clock when EXT timing is used. The external clock was lost for the  
previous second. This alarm is reset when the clock is active again.  
LOOPBACKS  
An HDSL system maintains several diagnostic loopback configurations, both toward and away from the local unit,  
which can be used to verify proper transmission of test data through the local unit, the HDSL facility, and the  
remote unit. Figure 8 on page 19 shows all possible loopback paths. Table 12 on page 20 lists available loopbacks.  
During loopbacks the system generates an Alarm Indication Signal (AIS) past the loopback point toward the far  
unit. Loopbacks can be activated from the LOC (local) and REM (remote) front-panel pushbuttons, the console  
Test menus, and the management unit interface. Table 13 on page 21 lists loopback equivalents for different  
activation methods. Only one loopback option can be enabled at a time. During a loopback, the Loopback LEDs  
on the front panel indicate the type of loopback currently present in the system. See Table 4, “Line and Desktop  
The system reverts to normal transmission of payload data after the specified timeout period has elapsed. If a  
timeout period is not specified, the loopback must be manually disengaged before normal transmission of data can  
resume.  
Test loopbacks disrupt normal end-to-end transmission of customer data and are the  
equivalent of taking the circuit out of service. The circuit does not revert to normal operation  
until loopbacks are disengaged manually or until after the specified loopback timeout period  
has expired.  
LTU Interface  
NTU Interface  
Single-pair  
HDSL loop  
HDSL  
HDSL  
Nx64k  
Nx64k  
Figure 8. Loopback Operations  
UTU-701 and ETU-751 List 1  
August 9, 2002  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Functional Description  
700-701-100-02  
Table 12. Loopbacks Selected at Front Panel Pushbuttons and Console Screens  
Description  
Loopback  
The two loopbacks that follow can be selected from the LOC and REM front-panel pushbuttons, the console screens, or the  
management unit interface.  
LOC Pushbutton—Local  
HDSL Loopback  
This is an analog loopback implemented in both HDSL transceivers, and enables a complete checkout  
of the local equipment by looping back data at the furthest point before the transmission media. The  
HDSL link goes down as a result of this loopback, and is therefore not selectable from the remote unit  
console screens.  
REM Pushbutton—Remote Data is transmitted across the HDSL link and looped back at the remote interface ports. The HDSL  
Loopback  
link must be up for this loopback to be available. With no HDSL link up, the REM button will not enable  
any loopbacks.  
The three loopbacks that follow are available exclusively from the console screens or management unit interface.  
Local Interface Loopback  
Data is looped back at the closest point in the local unit toward customer equipment. This loopback  
is useful for verification of a proper connection at the local interface between your DTE and the local  
HDSL card. The HDSL link is maintained during this loopback.  
Local or Interface Loopback Data is looped back at the local unit or remote unit back toward the remote DTE equipment. This is  
Away from the Local  
Equipment  
equivalent to pressing the REM button on the remote unit’s front panel, and is made available at the  
local console screen for ease of installation. The injected test data and loopback verification must still  
be performed at the remote unit site. Local equipment outputs an AIS for the duration of this test.  
Remote Interface Away  
from the Local Equipment  
Data is looped back at the remote unit toward the remote DTE equipment. This is available at the local  
console screen for the duration of this test. The injected test data and loopback verification must still  
be performed at the remote unit site. Local equipment outputs an AIS for the duration of this test.  
The following applies to LTU and NTU loopbacks:  
No inband loopback codes are recognized or generated.  
A remote HDSL loopback is not available from the local console screen as it causes the HDSL link to go down  
and requires user action at the remote unit to disengage the loopback.  
20  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
700-701-100-02  
Functional Description  
Table 13 summarizes the equivalent loopbacks for two different activation methods:  
LTU and NTU LOC and REM buttons  
console screen Test menus (see “Testing” on page 60 for loopback operation from the Test menus)  
Table 13. Loopback Equivalents  
Console Screen Test Menu  
Front Panel  
Loopback mode  
Loopback Position  
LTU LOC button  
LTU REM button  
NETWORK (a)  
NETWORK  
LTU-HDSL  
NTU-I/F  
NETWORK  
LTU-I/F  
NTU LOC button  
NTU REM button  
CUSTOMER (b)  
CUSTOMER  
CUSTOMER  
NTU-HDSL  
LTU-I/F  
NTU-I/F  
(a) Activated from console screen Test menu at LTU.  
(b) Activated from console screen Test menu at NTU.  
BER TESTING  
The HDSL units provide a mechanism for validating circuit integrity utilizing a pseudorandom bit sequence  
(PRBS) generator and BER meter internal to the LTU unit. This diagnostic test disrupts the normal flow of  
payload traffic, and requires the presence of a Network NTU-I/F loopback or an external physical loopback at the  
NTU interface connector. The test is run at the selected HDSL Payload Rate (see Table 18 on page 38). BER  
results are accumulated continuously and updated on the console screen at intervals of approximately 16 seconds.  
The PRBS data pattern is always generated at the LTU toward the HDSL channel, and the BER is always  
measured at the LTU based on data received from the HDSL channel. The test may be initiated and stopped from  
the Test menu at either the LTU or NTU console screen.  
The BER test must be stopped before leaving the test menu to restore normal  
payload transmission. Typing ESC while the BER test is in progress causes the  
following message to display: BER Test in Progress. Must STOP  
before leaving screen.”  
UTU-701 and ETU-751 List 1  
August 9, 2002  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Inspection, Safety, and Equipment Repair  
700-701-100-02  
INSPECTION, SAFETY, AND EQUIPMENT REPAIR  
This section describes the procedures to be followed regarding product inspection, safety, and repair.  
INSPECTION  
Open the line or desktop unit shipping carton and inspect the contents for signs of damage. If the equipment was  
damaged in transit, immediately report the extent of the damage to the transportation company and to ADC (see  
SAFETY  
To ensure safety of personnel and equipment, carefully observe the following safety rules:  
Input voltage for the UTU-701C line unit (nominal -48 Vdc, tolerance -36 to -72 Vdc) must be  
supplied by an isolated DC source that complies with TNV or earthed SELV requirements of the  
latest version of IEC 950.  
Be careful when installing or modifying telephone lines. Dangerous voltages can be present. It  
is unsafe to install telephone wiring during a lightning storm.  
Always disconnect all telephone lines and power connections before servicing or disassem-  
bling this equipment. All wiring external to the product should follow the local wiring codes.  
Die Eingangsspannung fuer die UTU-701C Karte is nominell –48 VDC, Toleranz -36 bis –72 VDC.  
Die Gleichstromquelle muss den Vorschriften gemäß der Norm EN60950 fuer  
Fernsprechnetzspannung (TNV) und Sicherheitskleinspannung (SELV) entsprechen.  
Bitte beachten Sie, dass beim Installieren oder Veraendern von Telefonleitungen gefaehrliche  
Spannungen entstehen koennen. Es ist ebenfalls gefaehrlich, waehrend eines Gewitters  
Installationen an Telefondraehten vorzunehmen.  
Bei Installation, Wartung oder Veraenderung des Geraetes muessen alle Telefon- und Netzkabel  
ausgezogen werden. Alle externen Verdrahtungsarbeiten sollten gemaess den  
Elektrizitaetsvorschriften des jeweiligen Landes ausgefuehrt werden.  
EQUIPMENT REPAIR  
To ensure the equipment does not become damaged, carefully observe the following cautions:  
If a problem has been isolated to this unit, do not attempt to repair it. The unit's components  
are not user serviceable and, therefore, must not be replaced. Please return the unit to ADC for  
repairs.  
Wenn eine Störung auf dieses Gerät zurückgeführt werden kann, sollte man nicht versuchen es  
zu reparieren. Die Geräteteile sind nicht vom Endverbraucher zu warten und müssen darum  
nicht ersetzt werden. Bitte senden Sie das Geräet zur Reparatur zurueck an ADC.  
22  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
700-701-100-02  
Installation and Startup  
INSTALLATION AND STARTUP  
This section describes the installation and startup procedures for the line and desktop units.  
UTU-701C LINE UNIT INSTALLATION  
Perform the following steps to install the UTU-701C line unit.  
The chassis ground of the shelf or remote enclosure receiving these units must be connected  
to earth ground for protection of the equipment and for safety of personnel.  
Primary protection for the HDSL line must be provided by the user. Both primary and secondary  
protection must be provided by the user if the E1 line runs outside of the building.  
1
2
3
4
Align the UTU-701C with the card guides in the shelf or enclosure (see Figure 9).  
Slide the line unit into the guides, then push the unit inward until it seats firmly in the card-edge connector.  
Tighten the two captive screws on the UTU-701C front panel to secure the unit in place.  
If configuring the line unit as an LTU, power up the shelf and proceed as instructed on pages 25 through 27  
and 37 to access the Local Unit Role option in the Config System Settings menu (the default setting is NTU).  
5
Set the TT clock at the DTE for the default HDSL payload rate of 256 kbps (4 time slots).  
EMS-83x  
UTU-701C  
Figure 9. Installing the UTU-701C Line Unit  
UTU-701 and ETU-751 List 1  
August 9, 2002  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installation and Startup  
700-701-100-02  
The line and desktop units will reset and their LEDs will sequence through the startup cycle  
following any change to the Local Unit Role option. If necessary, log on again by pressing the  
SPACEBAR several times.  
ETU-751C DESKTOP UNIT INSTALLATION  
Perform the following steps to install an ETU-751C desktop unit.  
1
2
3
Insert the AC power cord into the power cord receptacle on the ETU rear panel.  
Plug the power cord into a source of 100 V to 240 V, 50 or 60 Hz AC power.  
If configuring the desktop unit as an LTU, power up the shelf and proceed as instructed on pages 25 through  
27 and 37 to access the Local Unit Role option in the Config System Settings menu (the default setting is  
NTU).  
4
5
Connect the DTE cables to the 120 or 75 connectors on the ETU-751C rear panel.  
Connect the HDSL line cable to the HDSL line connector on the ETU rear panel.  
HDSL STARTUP AND SYNCHRONIZATION  
The rate selectable LTU holds the configuration settings for the rate selectable NTU. At startup, the LTU first  
confirms that the NTU is a rate selectable unit. The LTU then configures the NTU with the required settings.  
Power up the rate selectable units and observe the synchronization process as follows:  
1
2
Power up the shelf or enclosure where the units are installed.  
Confirm the following:  
The HDSL ALM LED is on and the HDSL SYNC LED flashes once per second as the units  
self-configure and establish synchronization.  
After approximately 60 seconds the HDSL ALM LED is off and the HDSL SYNC LED is steady green.  
The units are now ready for configuration through the console screen menus.  
If the HDSL SYNC LED continues to flash after 90 seconds, the HDSL line is faulty or one of the  
units is not a rate selectable unit. Check for the correct line units. Test the HDSL line using the  
loopbacks described in “Testing” on page 60. Front panel loopback (LPBK) LED indications are  
described in Table 4 on page 6.  
The LTU and NTU will reset and their LEDs will cycle through the startup sequence following  
any change to the HDSL Payload Rate option (see “Configure System Settings” on page 37).  
24  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
System Configuration  
SYSTEM CONFIGURATION  
Each line unit provides a system-wide view of the entire HDSL circuit, including the remote unit. After  
establishing communication with the remote line card, provisioning information can be set and performance can  
be monitored from the local unit. If the HDSL link is down, the only parameters that can be changed are those on  
the local line unit. The LTU overwrites any NTU settings when the link is re-established. The LTU also provides  
a special lockout feature that prevents users plugged into the NTU console port from changing the circuit  
configuration. When enabled, the maintenance terminal connected to an NTU provides a read-only view of the  
entire HDSL system.  
The console screen menus are not available when the HDSL card is under the control of a shelf  
management unit.  
The line unit option settings are stored in non-volatile RAM (NVRAM). No dip switches or jumpers are required  
to configure these options. These options are set from the console screen menus or management unit interface.  
Option settings stored in NVRAM are retained if the line unit loses shelf power.  
MAINTENANCE TERMINAL CONNECTION  
The maintenance terminal (or PC running a terminal emulation program) is used to access the console screen  
menus. Through these menus, the system is configured, monitored, tested, and its circuit inventory is displayed.  
Maintenance terminal  
DB-9 Connector  
(DTE)  
4
UTU/ETU  
Console port  
3
2
DB-9 Connector  
5
(DCE)  
DTR (Data Terminal Ready)  
TD (Transmit Data)  
4
3
2
5
Maintenance terminal  
RD (Receive Data)  
GND  
DB-25 Connector  
(DTE)  
20  
3
2
7
Figure 10. UTU/ETU Console Port and Maintenance Terminal Connector Pinouts  
UTU-701 and ETU-751 List 1  
August 9, 2002  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
System Configuration  
700-701-100-02  
To connect and configure a maintenance terminal:  
1
Connect a serial cable from the maintenance terminal 9-pin COM port to the line or desktop unit console port  
connector (Figure 11). Ensure the Data Terminal Ready (DTR) signal from the terminal is connected as the  
HDSL card will not communicate without it. Data Terminal Ready (DTR) may also be asserted by connecting  
the DSR output signal (pin 6) to the DTR input (pin 4).  
Line unit  
Maintenance terminal  
i
9-pin COM port  
Interface cable  
Console port  
Figure 11. Connecting a Maintenance Terminal to a Line Unit  
2
Configure the maintenance terminal for the following communication settings:  
VT100 Emulation or ANSI (if VT100 is not available)  
Clear the modem initialization string, if supported by the terminal  
Bits per second: 1200, 2400, 4800, 9600 (default), or 19200 bps (recommended)  
Data bits: 8  
Parity: None  
Stop bits: 1  
Flow Control: None  
If using a PC and Microsoft Windows terminal emulation program, deselect Show Scroll Bars and Use Function,  
Arrow, and Ctrl Keys from the Settings Terminal Preferences menu in Windows 3.1 or from the Properties menu  
in Windows 95.  
MODEM CONNECTION  
For remote access to the line unit, an auto-answer modem can be connected to the console port. Use a null modem  
cable to connect the WorldDSL line unit and the modem.  
26  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
System Configuration  
LOGGING ON  
To log on to the maintenance terminal console screen:  
1
Press the SPACEBAR several times to display the Logon Password screen (Figure 12).  
Figure 12. Logon Password Screen  
The ENTER key is the factory default password. If you establish a different password, you must  
type the new password (single word, no spaces, up to eight characters) on a subsequent log on.  
If the system does not respond, verify that the Hardware Flow Control of the maintenance  
terminal is set to NONE.  
2
Type the password at the prompt or press ENTER if a password has not been customized. The console screen  
menu bar displays (Figure 13).  
Figure 13. Console Screen Menu Bar  
UTU-701 and ETU-751 List 1  
August 9, 2002  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
System Configuration  
700-701-100-02  
CONSOLE SCREEN STRUCTURE  
The following sections describe the structure of the console screen and how to navigate through its menus and  
related displays.  
The structure of the console screen displays and drop-down menus is shown in Figure 14. The names in the  
console screen menu bar identify each display and menu. The arrows in the menu bar following the Monitor,  
History, and Config names indicate the presence of a drop-down menu or sub-menu. The designations Display  
and Displays indicate that one or more displays are associated with the name in the menu bar or its drop-down  
menu.  
Figure 14. Console Screen Menu Structure  
28  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
System Configuration  
Table 14 describes the drop-down menus selected from the console screen.  
Table 14. Console Screen Menus  
Menu Name  
Function  
Described in this section  
Main  
Display the Main console screen to:  
View the circuit configuration  
View performance summary information  
View alarm summary information  
Monitor  
History  
Monitor the past 24-hour performance of the LTU interfaces, NTU  
interfaces, or HDSL spans.  
View 24-hour, 7-day, or alarm history displays for any of  
the following:  
LTU interface  
HDSL spans  
NTU interface  
Clear all the 24-hour, 7-day or alarm histories  
Config  
Perform any of the following system functions:  
View or change global operating parameters for the system  
View or change LTU interface, HDSL span, or NTU interface operating  
parameters  
View or change alarm parameters  
Set the time and date  
Set or change the unit password  
Change the circuit ID  
Configure terminal display  
Set all operating parameters to factory defaults  
Test  
Perform any of the following test functions:  
Set the loopback mode and location  
Set the loopback time-out  
Enable or disable loopback operation  
Initiate BER test and monitor BER results  
Inventory  
Display registration information to track product manufacturing,  
configuration, and revision state.  
Quit  
Log off the system.  
-
Help  
Display a screen of helpful information regarding the product.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
System Configuration  
700-701-100-02  
READING AND NAVIGATING MENUS  
The menu and status bars appear on all console screens. The information on the rest of the screen varies depending  
on the function of the menu or screen.  
The menu bar displays the name of each menu. Choosing Monitor, History, or Config from the menu bar drops  
down a menu of available options. When selected, all options on the Monitor drop-down menu, and the Alarm  
option on the Config drop-down menu, display drop-down submenus.  
The status bar at the bottom of the screen displays the circuit ID, the current date and time, unit type, and current  
system information. Select Config from the console screen menu bar to enter or change the circuit ID and the  
current date and time. The items described in Table 15 correspond to the numbers in Figure 15.  
Table 15. Console Screen Status Bar Displays  
Item  
Field  
Description  
1
2
3
4
Circuit ID  
Shows the user-selected name for the circuit (such as customer name).  
Today's date in dd/mm/yy format. Today's time in 24-hour format.  
Either LTU or NTU.  
Date and time  
Local unit role  
System information  
Displays the current system status. The system information field shows one of  
the following:  
Loop down - At least one configured HDSL channel is down, either due to  
restart, or startup not completing.  
Alarm - A major alarm condition is currently active in the system. In the case  
of a loopback bringing the loop down, LOSW alarms will be ignored.  
Loopback - The system is in a diagnostic loopback configuration.  
Update - Circuit-wide provisioning is in progress.  
Normal - All configured HDSL channels are up in the circuit, no alarms are  
present, and provisioning is complete.  
2
3
4
1
Figure 15. Items in Console Screen Status Bar  
30  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
System Configuration  
Use the keys described in Table 16 to navigate the console screen and its menus:  
Table 16. Console Screen Navigation Keys  
To Perform this Function  
Press this Key  
Alpha-numeric keys  
Type the underlined or highlighted letter to select and execute a menu item. For example on the  
Main console menu, type C to access the Config drop-down menu.  
Also use these key to enter values in text fields. For example, on the Config Date and Time menu,  
type the date in a DD/MM/YY format.  
and  
and  
keys  
keys  
Moves horizontally across the Menu bar, except when in a text entry field.  
Press the  
and  
keys from the Main console screen to access drop-down menus and their  
menu items. For example:  
press the and keys to select Config in the menu bar and press the key to access the  
drop-down configuration menu, then  
press the  
and  
keys to highlight a menu item and press ENTER to select the item.  
TAB key  
Provides same function as the  
key.  
CTRL + E moves up one line in the History screens.  
CTRL + E  
CTRL + X  
CTRL + C  
CTRL + R  
SPACEBAR  
CTRL + X moves down one line in the History screens.  
CTRL + C performs the page-down function in the History screens.  
CTRL + R performs the page-up function in the History screens.  
Selects options displayed for current menu item. For example, to select MANUAL or Nx64k AUTO  
mode from the Config System Settings menu:  
press the  
key to highlight the HDSL Rate Mode option, then  
press the SPACEBAR until the desired option (MANUAL or Nx64k AUTO) is highlighted.  
Exits the current screen and returns to the previous screen. Selection changes made on the  
current screen are discarded. Press ESC while in a text field to cancel the text entry and restore  
the old value.  
ESC  
Applies all selections on the current screen. For example, to select an HDSL payload rate from  
the Config System Settings menu:  
ENTER  
press the  
key to highlight the HDSL Payload Rate option, then  
type the desired number of time slots (1 to 4) and press ENTER to display the selected HDSL  
payload rate (in MANUAL mode only).  
UTU-701 and ETU-751 List 1  
August 9, 2002  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
System Configuration  
700-701-100-02  
Config Menu Options  
Type C at the console screen (Figure 15) to display the Config menu (Figure 16). Table 17 lists the Config menu  
options and the order of system configuration.  
Figure 16. Console Screen Config Menu  
Table 17. Config Menu Options and Recommended Order of System Configuration  
Use this Option  
To:  
See page:  
Terminal Settings  
Date and Time  
Password  
Select the best viewing mode for the console screen.  
Set the system date and time.  
Set or change the system password.  
Circuit ID  
Assign a circuit ID.  
System Settings  
LTU and NTU Interface  
Alarms  
Select and configure system-wide operating parameters.  
Select and configure LTU/NTU-specific operating parameters.  
Enable or disable alarms and to select alarm severity.  
Reset all operating parameters to factory settings.  
Set to Factory Dflts  
Observe the following when configuring a system:  
Configure settings in the order specified in Table 17. The System Settings must be configured before the LTU  
and NTU Interface settings. Changing System Settings can clear values configured in LTU and NTU Interface  
settings.  
When using a UTU as an LTU, change the Local Unit Role for the unit using the Config System Settings  
menu. Note that changing the Local Unit Role of a UTU causes the unit to reset and the LEDs to cycle.  
When the HDSL units are reset or cycle power, the date field is preserved but the time field is not preserved.  
Set the time using the Config Date and Time display. When the HDSL units are turned off and left off for a  
longer period of time (more than 24 hours, for example), set both the date and time using the Config Date and  
Time display since neither value was preserved.  
32  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
System Configuration  
Configure Terminal Settings  
The console screens use line drawing characters to enclose menu selections and dialog boxes.  
Because not all maintenance terminals and terminal emulation programs adhere consistently to  
the VT100 standard, the HDSL card allows you to adjust the display for best results on a given  
terminal.  
1Type T at the Config drop-down menu to display the Config Terminal Settings menu (Figure 17).  
Figure 17. Config Terminal Settings Menu  
Press the or key to highlight the selection that matches the terminal configuration (which should also  
2
be the selection most clearly displayed on the monitor). The choices are:  
VT100  
Windows Terminal  
IBM PC  
ASCII  
3
Press ENTER to confirm the selection.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
System Configuration  
700-701-100-02  
Configure Date and Time  
1Type D at the Config drop-down menu to display the Config Date and Time menu (Figure 18).  
Figure 18. Config Date and Time Menu  
2
3
Type the date in DD/MM/YY format, then press ENTER .  
Type the time in HH : MM format (24-hour clock), then press ENTER .  
The system date and time appear on the status line of the console screen and is useful when viewing alarm  
histories. When the HDSL units are reset or cycle power, the values in the date field are saved but the values in  
the time field are reset to 00 : 00. Set the time using the Config Date and Time display. When the HDSL units are  
turned off and left off for more than 24 hours, both the date and time must be set using the Config Date and Time  
display (neither value is saved after 24 hours).  
Changing the date and time after the system has been running will not automatically clear alarm  
histories. This must be done after setting the date and time. (See “Clear History Screens” on  
page 58.)  
34  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
System Configuration  
Change Password  
1Type P at the Config drop-down menu to display the Config Change Password menu (Figure 19).  
Figure 19. Config Change Password Menu  
2
3
Enter a new password (up to eight characters) to change the current system password.  
Retype the new password (up to eight characters) to confirm its accuracy.  
When changing the default password ( ENTER ), save the new password in a secure place. A  
password cannot be recovered if it is forgotten. Contact ADC if assistance is needed (see  
UTU-701 and ETU-751 List 1  
August 9, 2002  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
System Configuration  
700-701-100-02  
Configure Circuit ID  
The circuit ID appears on the status line of each console screen. Choose a unique circuit ID for each HDSL card.  
1Type C at the Config drop-down menu to display the Config Circuit ID menu (Figure 20).  
Figure 20. Config Circuit ID Menu  
2Type a new circuit ID (up to 23 characters) to change the current circuit ID.  
36  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
System Configuration  
Configure System Settings  
Use the System Settings menu to select and configure system-wide operating parameters. Configure system  
settings as follows:  
1
Type S at the Config drop-down menu to display the Config System Settings menu. Figure 21 shows the  
Config System Settings menu for the UTU-701C and ETU-751C.  
Figure 21. Config System Settings Menu  
2
Do the following for each system option setting to be changed. Table 18 on page 38 describes the fields and  
options displayed in the Config System Settings menu. The settings in boldface type are factory default  
settings.  
Use the or the key to select the sub-menu item to be changed.  
Use the SPACEBAR to toggle to the appropriate option or type in the correct information, then press  
ENTER to select the option.  
When using a UTU or ETU as an LTU, configure the Local Unit Role option first.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
System Configuration  
700-701-100-02  
Table 18. Fields and Options Displayed in Config System Settings Menu  
Field and Options  
Description  
Application Mode (a)  
SINGLE  
System uses a single-pair of twisted copper wire to transport data. For more information, see  
HDSL Rate Mode (a)  
Selects the mode with which the HDSL payload rate will be determined.  
MANUAL  
HDSL payload rate is set by number of time slots entered for the HDSL Payload Rate option.(b)  
Each time slot is 64 kbps.  
HDSL Payload Rate (c)  
Selects the rate and reach at which data will be transported (see Table 2, “Transmission  
256kbps/4  
Typing a time slot value of 1 through 32 and pressing ENTER sets and displays the HDSL  
payload rate. (d) (e)  
Remote Console Access  
Selects whether a maintenance terminal connected to an NTU can affect system changes or  
is Read-only. This field may be set only at the LTU.  
ALLOWED  
NTU console screens can be used to configure the system.  
BLOCKED  
NTU console screens are read-only. The LOC and REM pushbuttons on the NTU are also  
disabled. System changes can only be made from the LTU.  
Local Unit Role  
Configures UTU or ETU as LTU (master) or NTU (slave). The default configuration is NTU  
(slave). Note that changing the Local Unit Role of a UTU or ETU causes the unit to reset and  
the LEDs to cycle.  
LTU  
Configures UTU or ETU as LTU (master). The LTU-configured rate selectable UTU/ETU does  
not provide line power to other HDSL units.  
NTU  
Configures UTU or ETU as NTU (slave). The NTU-configured rate selectable UTU/ETU does not  
provide line power to other HDSL units.  
(a) SINGLE is the only application mode and MANUAL is the only rate mode.  
(b) UTU-701C and ETU-751C have 32 time slots available for HDSL payload rates of 256 kbps to 2048 kbps.  
(c) An HDSL Payload Rate of 64 kbps (1 time slot) is transmitted at 256 kbps (see “G.704 Framing and Rate Selectable HDSL” on page 17).  
(d) Payload rates are displayed in the Config LTU and Config NTU Interface menus as Data Rate/# of TSs (data rate/number of time slots).  
(e) Changing the HDSL Payload Rate or Local Unit Role causes the unit to reset and the LEDs to cycle. Log on again by pressing the  
SPACEBAR several times.  
38  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
700-701-100-02  
System Configuration  
Configure LTU and NTU Interfaces  
Select and configure the LTU- and NTU-related operating parameters as follows:  
1
Type one of the following at the Config drop-down menu to display the Config LTU or NTU Interface menu:  
L for the Config LTU Interface menu (Figure 22).  
N for the Config NTU Interface menu (Figure 23).  
Figure 22. Config LTU Interface Menu  
Figure 23. Config NTU Interface Menu  
The Data Rate/# of TSs and Beginning TS parameters in the Config LTU and NTU Interface  
menus are read-only displays. The Data Rate/# of TSs value is set in the Config System  
Settings menu as the “HDSL Payload Rate” (See Figure 21 on page 37). The Beginning TS  
value is 0 with 32 time slots selected (unstructured mode) and 1 when less than 32 time slots  
are selected (structured mode).  
UTU-701 and ETU-751 List 1  
August 9, 2002  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
System Configuration  
700-701-100-02  
2
Do the following for each interface option to be changed. Table 19 describes the fields and options displayed  
in the Config LTU and Config NTU Interface menus.  
Use the or the key to select the sub-menu item to be changed.  
Use the SPACEBAR to toggle to the appropriate option or type in the correct information, then press  
ENTER to select the option.  
The settings in boldface type in Table 16 are factory default settings.  
Table 19. Fields and Options in Displayed Config LTU and Config NTU Interface Menus  
Field and Options  
Description  
Primary Timing Source  
Selects the clock source for the HDSL transmit direction.  
External 2.048 MHz clock (UTU-701C only)  
Input E1 clock  
EXT  
G.703  
G.703 Port  
CRC-4 Mode  
DIS  
Cyclic Redundancy Check (CRC) to detect errors in transmitted data. Available only when less  
than 32 time slots are selected (places unit in structured application mode).  
CRC-4 mode is disabled. CRC-4 mode is not available (N/A) when 32 time slots are selected  
(places unit in unstructured application mode).  
ENA  
The input G.703 signal is monitored for CRC-4 multiframe errors. A new CRC-4 code is output  
for use at the remote unit. Detected errors are displayed in the Monitor LTU and NTU Interface  
screens.  
PASSTHRU  
Idle Code  
All time slot 0 bits are passed unchanged to the remote unit. Useful when detection of CRC-4  
errors is performed by customer equipment.  
User inputs the idle pattern (from 00 to FF) transmitted in unused time slots from LTU or NTU  
G.703 port. Factory default setting is FF.  
Data Rate/# of TSs  
Read-only display of indicated HDSL data rate and corresponding number of time slots (TSs)  
as set with HDSL Payload Rate option in the Config System Settings menu (See “G.704  
Framing and Rate Selectable HDSL” on page 17). Default setting is 256kbps/4.  
Beginning TS  
Read-only display of beginning time slot. This setting is 0 (zero) in the structured mode and  
one (1) in the unstructured mode.  
40  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
700-701-100-02  
System Configuration  
Configure Alarms  
Use the Config Alarms menu to configure LTU and NTU Interface alarm parameters and the HDSL span alarm  
parameters. When setting alarm parameters for LTUs and NTUs, keep the following rules in mind:  
Disabled alarms do not cause LED indications and are not stored in history. Console screen menu alarm  
history reports are not generated.  
Minor alarms cause LED indications and are stored in history. Console screen menu alarm history reports are  
generated.  
Major alarms cause LED indications, actuate the line unit alarm relay, and are stored in history. Console  
screen menu alarm history reports are generated.  
The LTU alarm relay activates in response to a major alarm at the LTU only.  
The NTU alarm relay activates in response to a major alarm at the NTU only.  
For the duration of a major alarm, the line unit alarm relay contacts are connected as follows:  
The C (Common) contact is connected to the NO (Normally Open) contact.  
The NC (Normally Closed) contact is floating.  
With no alarm, the C and NC contacts are connected, and the NO contact remains floating.  
The line unit alarm relay operates in a fail-safe mode. When no power is applied to the line unit, the alarm  
relay C and NO contacts are connected with the NC contact floating.  
Type A at the Config drop-down menu to display the Config Alarms menu (Figure 24).  
Figure 24. Config Alarms Menu  
UTU-701 and ETU-751 List 1  
August 9, 2002  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
System Configuration  
700-701-100-02  
Alarms for LTU and NTU Interface  
1
Type one of the following at the Config Alarms drop-down menu to display the Config Alarms LTU or Config  
Alarms NTU Interface menu:  
L for the Config Alarms LTU Interface menu (Figure 25)  
N for the Config Alarms NTU Interface menu (Figure 26)  
Figure 25. Config Alarms LTU Interface Menu  
Figure 26. Config Alarms NTU Interface Menu  
2
Do the following for each interface option to be changed. The fields displayed in the Config Alarms LTU and  
Config Alarms NTU Interface menus are described in Table 20.  
Use the or key to select the sub-menu item to be changed.  
Use the SPACEBAR to toggle to the appropriate option or type in the correct information, then press  
ENTER to select the option.  
42  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
System Configuration  
Table 20. Fields Displayed in Config Alarms LTU and Config Alarms NTU Interface Menus  
Field  
Description  
Loss of Signal (LOS)  
Loss of signal at the G.703 input.  
Loss of Frame Alignment (LFA)  
Loss of frame alignment at the G.703 input.  
Receive Alarm Indication Signal (AIS) Alarm indication signal (unframed all ones) received at the G.703 input.  
Remote Alarm Indication Signal (RAI) Remote alarm indication signal received at the G.703 input (through A-bit).  
Loss of Clock (LOC)  
Applies to loss of external clock when EXT timing is used. The external clock was lost for  
the previous second. This alarm is reset when the clock is active again.  
HDSL Span 1 Alarms  
1
Type 1 at the Config Alarms drop-down menu to display the Config Alarms HDSL Span 1 menu (Figure 27).  
Figure 27. Config Alarms HDSL Span 1 Menu  
2
Do the following for each interface option to be changed. The fields displayed in the Config Alarms HDSL  
Span 1 menu are described in Table 21 on page 44.  
Use the or  
key to select the sub-menu item to be changed.  
Use the SPACEBAR to toggle to the appropriate option or type in the correct information, then press  
ENTER to select the option.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
System Configuration  
700-701-100-02  
Table 21. Fields Displayed in Config Alarms HDSL Span 1 Menu  
Field  
Description  
Margin (MAR)  
Selects whether the alarm is disabled (DIS), or enabled and reported as a Minor (MIN) or Major  
(MAJ) Alarm when the margin falls below the threshold. This indicates a potential degradation of  
line quality. If an alarm is configured as a protection switch (PSW), it will behave as a Major (MAJ)  
Alarm, and cause protection switching to engage.  
Margin Threshold  
Selects the margin alarm threshold (from 0 dB to 15 dB) for all four margin measurements of the  
span.  
Errored Seconds (ES)  
24 HR ES Threshold  
Loss of Sync Word (LOSW)  
Selects whether the alarm is disabled (DIS), or enabled and reported as a Minor (MIN) or Major  
(MAJ) Alarm when 24-hour ES count exceeds the threshold.  
Selects the errored seconds threshold (0 to 255) for all four errored seconds measurements of the  
span measured over a 24-hour period.  
Selects whether the alarm is disabled (DIS), or enabled and reported as a Minor (MIN) or Major  
(MAJ) Alarm when the LOSW condition (HDSL loop down) occurs.  
Power Feed Open  
Power Feed Short  
Not supported. These units do not supply power to other units.  
Not supported. These units do not supply power to other units.  
SET TO FACTORY DEFAULTS  
Set to Factory Dflts is the screen from which all operating options can be reset to the ADC factory defaults.  
1
Type F at the Config drop-down menu to display the Set to Factory Dflts screen (Figure 28).  
Figure 28. Set to Factory Defaults Screen  
2
Press ENTER to reset value to factory defaults. A confirmation message appears at the bottom of the display:  
SETTING FACTORY DEFAULTS ... SERVICE *WILL* BE INTERRUPTED! ARE YOU SURE(Y/N)?  
44  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
System Configuration  
3
Do one of the following:  
Type N to keep the current settings.  
Type Y to reset values to factory defaults. The system resets and both LTU and NTU units go through  
their respective synchronization processes. If loops are down or are in update mode while Set to Factory  
Dflts is enabled, only the local unit will restart. If the loops are up, both the LTU and NTU will restart.  
The factory default system settings are listed in Table 22.  
Table 22. Factory Default System Settings  
Operating Option  
Default Setting  
System Settings  
Application Mode  
SINGLE  
HDSL Rate Mode  
MANUAL  
HDSL Payload Rate  
Remote Console Access  
Protect Switch Command  
Local Unit Role  
256kbps/4  
ALLOWED  
Not supported on these units.  
NTU  
LTU/NTU Interface  
G,703 port  
Interface Type  
Data Rate/# of TSs  
Beginning TS  
G.703  
256 / 4  
0 (structured mode)  
1 (unstructured mode)  
Alarms LTU/NTU Interface  
Loss of Clock (LOC)  
Alarms HDSL Spans  
Margin (MAR)  
MIN (Minor)  
MIN (Minor)  
Margin Threshold  
6
Errored Seconds (ES)  
24 Hour ES Threshold  
Loss of Sync Word (LOSW)  
Power Feed Open (PFO)  
Power Feed Short (PFS)  
MIN (Minor)  
70  
MAJ (Major)  
Not supported on these units.  
Not supported on these units.  
LOGGING OFF  
If the maintenance terminal must be left unattended for any length of time, log off until work resumes. This  
prevents unauthorized persons from inadvertently changing operating parameters.  
Log off by choosing Quit from the menu bar or by disconnecting the cable connecting the maintenance terminal  
to the line or desktop unit. Automatic log off occurs after 20 minutes of keyboard inactivity.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Viewing Status  
700-701-100-02  
VIEWING STATUS  
The following sections describe the screens that display status and system information, such as current alarm  
status, performance history, product, and configuration information.  
View status using a maintenance terminal or PC running a terminal emulation program connected to the V.24  
(RS-232) console port. See page 25 for instructions on connecting a maintenance terminal or PC.  
MAIN CONSOLE SCREEN  
The Main console screen displays a summary of LTU and NTU circuit configuration, performance statistics, and  
alarm status for each interface in the circuit.  
Type M to display the Main console screen (Figure 29). The screen shown in Figure 29 is a display of the LTU  
and NTU in the single-pair application. The numbered fields are described in Table 23.  
1
2
4
3
Figure 29. Main Console Screen  
Table 23. Reading the Main Console Screen  
Field  
Description  
1
2
3
4
Shows performance and alarms for the LTU user interface.  
Shows performance and alarms for the LTU HDSL interface.  
Shows performance and alarms for the NTU HDSL interface.  
Shows performance and alarms for the NTU user interface.  
46  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
700-701-100-02  
Viewing Status  
Table 24 describes the fields displayed on the Main console screen.  
Table 24. Fields Displayed in Main Console Screen  
Description  
Field  
Circuit Configuration  
Indicates the interface standard for G.703 data port.  
Indicates the number of time slots (n) mapped to the G.703 interface.  
Indicates the primary source the unit uses for clock synchronization:  
External 2.048 MHz clock.  
G.703  
n TS  
Timing  
EXT  
G.703  
G.703 port receive clock.  
Application mode  
Indicates that the Single Pair (SINGLE) application mode is in effect.  
Performance  
MAR1  
Displays the Margin value for each HDSL interface or displays link status (SIG, ACQ, etc.) if the link  
is not up.  
MAR2  
ES1  
Reserved  
Displays the Errored Seconds (ES) counts for each HDSL interface. The counts are for the latest  
24-hour period, calculated as the sum of the counts in the previous 95 15-minute intervals, plus  
the count in the current 15-minute interval.  
ES2  
Reserved  
Alarms  
The Alarms field displays a list of all active alarms at each LTU/NTU and HDSL interface.  
Possible LTU/NTU Interface Alarms  
Loss of Signal (LOS)  
Loss of signal at the G.703 input.  
Loss of Frame Alignment (LFA) Loss of frame alignment at the G.703 input.  
Receive Alarm Indication  
Signal (AIS)  
Alarm indication signal (unframed all ones) received at the G.703 input.  
Remote Alarm Indication  
Signal (RAI)  
Remote alarm indication signal received at the G.703 input (through A-bit).  
Loss of Clock (LOC)  
Applies to loss of external clock when EXT timing is used. The external clock was lost for the  
previous second. This alarm is reset when the clock is active again.  
Possible HDSL alarms  
Margin (MAR)  
Margin has fallen below threshold set for the HDSL interface.  
Errored Seconds (ES)  
Loss of Sync Word (LOSW)  
Errored seconds count has exceeded threshold set for the HDSL interface.  
Loss of sync word at the HDSL interface. Remains active during restart, but not a cold start.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Viewing Status  
700-701-100-02  
MONITOR MENU  
The Monitor menu contains the following options:  
LTU Interface screen that displays the 24 hour and cumulative count of errors at the LTU G.703 port.  
NTU Interface screen that displays the 24 hour and cumulative count of errors at the NTU G.703 port.  
HDSL Span 1 screen that displays the circuit performance and 24-hour error counts at the HDSL span 1  
interface.  
Type 0 at the console screen to display the Monitor menu (Figure 30).  
Figure 30. Monitor Menu  
48  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
Viewing Status  
Monitor LTU Interface Screen  
At the Monitor menu (Figure 30), type L to display the Monitor LTU Interface screen (Figure 31). Table 25  
describes the fields displayed in the Monitor LTU and Monitor NTU Interface screens.  
Figure 31. Monitor LTU Interface Screen  
Table 25. Fields Displayed in Monitor LTU and Monitor NTU Interface Screens  
Field  
Description  
G.703 Port  
Errored Seconds (ES)  
24 Hour Count  
The number of one-second intervals in which at least one bipolar violation (BPV) or one CRC-4  
error was detected at the G.703 input port during the last 24hours.  
SeverelyErroredSeconds(SES) The number of one second intervals during which a Loss of Signal (LOS), an Alarm Indication  
24 Hour Count  
Signal (AIS), or a Loss of Frame (or CRC-4 Multiframe) Alignment (LFA) occurred at the incoming  
port.  
Unavailable Seconds (UAS)  
24 Hour Count  
The number of seconds that G.703 input signals were unavailable during the last 24 hours. After  
ten consecutive SESs, the system is deemed unavailable, and the current UAS counter begins  
counting from ten. After ten consecutive non-SESs, the system returns to availability, and the ten  
counts representing the non-SESs are removed from the UAS counter.  
CRC Errored Seconds  
(Cumulative)  
The number of CRC-4 errors that were detected at the G.703 port since error counters were last  
cleared. Turning CRC-4 mode on (ENA) and off (DIS) clears the CRC-4 error counter.  
Bipolar Violation Seconds  
(Cumulative)  
The number of seconds in which bipolar violations were detected at the G.703 port since error  
counters were last cleared.  
Clear 24-Hour History  
The date and time that the 24-hour histories were last cleared are displayed here. Enable this  
function by pressing L or ENTER to clear all 24-hour history counters (including HDSL). This  
action must be confirmed by pressing Y .  
UTU-701 and ETU-751 List 1  
August 9, 2002  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Viewing Status  
700-701-100-02  
Monitor NTU Interface Screen  
At the Monitor menu (Figure 30), type N to display the Monitor NTU Interface screen (Figure 32).  
The fields displayed in the Monitor NTU Interface screen are identical to those displayed in the Monitor LTU  
Interface screen (see Table 25 on page 49).  
Figure 32. Monitor NTU Interface Screen  
50  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
Viewing Status  
Monitor HDSL Span 1 Screen  
The HDSL Span 1 screen (Figure 33) displays the circuit performance and 24-hour error counts at the HDSL span  
1 interface. A span is defined as the link between two HDSL units (that is, from an LTU to an NTU) which, in this  
case, is comprised of a single loop (that is, one twisted-copper pair). The values under the LTU-1 column represent  
HDSL Span 1 as measured by the LTU. The values under the NTU-1 column represent HDSL Span 1 as measured  
by the NTU.  
At the Monitor menu (Figure 30), type 1 to select the Monitor HDSL Span 1 screen (Figure 33). The fields  
displayed in the Monitor HDSL Span 1 screen are described in Table 26.  
Figure 33. Monitor HDSL Span 1 Screen  
Table 26. Fields in Monitor HDSL Span 1 Screen  
Field  
Description  
Current Margin (dB) (MAR)  
Indicates the excess signal-to-noise ratio relative to a 10-7 bit error rate. The normal range of  
a typical margin is from 6 to 22 dB, with a value of 6 dB corresponding to a predicted BER of 10-10  
.
Low Margin (dB)  
High Margin (dB)  
Indicates the lowest margin since startup or the last 24-hour history clear.  
Indicates the highest margin since startup or the last 24-hour history clear.  
Pulse Attenuation (dB)  
Indicates the attenuation of the 2B1Q pulse from the distant end. This value is related to the cable  
pair’s loss at 292 KHz. The normal range of pulse attenuation is from 1 to 41 dB.  
Errored Seconds (ES)  
The number of one-second intervals in which at least one HDSL CRC-6 error or loss of Sync Word  
(LOSW) was detected on the HDSL span during the last 24 hours.  
Unavailable Seconds (UAS)  
HDSL Tip/Ring Reversal  
The number of seconds that the HDSL span was down during the last 24 hours.  
Indicates whether the two conductors of the HDSL span are correctly connected or have been  
interchanged. The system automatically compensates for an interchange of wire leads.  
Clear 24-Hour History  
The date and time that the 24-hour histories were last cleared are displayed here. Enable this  
function by pressing L or ENTER to clear all 24-hour history counters (including HDSL). This  
action must be confirmed by pressing Y .  
UTU-701 and ETU-751 List 1  
August 9, 2002  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Viewing Status  
700-701-100-02  
HISTORY MENU  
The History menu contains the following status screens:  
LTU/NTU Interfaces that display alarm performance history for the LTU and NTU interface.  
HDSL Span that displays 24-hour, 7-day, and alarm performance history for the HDSL span.  
The History menu also provides the option to clear the 24-hour, 7-day, and alarm history screens. This option is  
described on page 58.  
Type H to select the History menu (Figure 34).  
Figure 34. History Menu  
52  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
Viewing Status  
LTU and NTU Interface Performance History Screens  
At the History menu (Figure 34), type L to select the History LTU Interface menu (Figure 35).  
Figure 35. History LTU Interface Menu  
At the History menu (Figure 34), type N to select the History NTU Interface menu (Figure 36).  
Figure 36. History NTU Interface Menu  
UTU-701 and ETU-751 List 1  
August 9, 2002  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Viewing Status  
700-701-100-02  
Only the Alarm History screen is available for the LTU and NTU interfaces. The 24 Hour and  
7 Day History screens, as well as the Alarm History screen, are available for HDSL Span 1.  
LTU and NTU Interface Alarm History Screens  
At the History LTU or History NTU Interface menu, type the A key to select an Alarm History status screen. The  
LTU Interface Alarm History screen is shown in Figure 37.  
Figure 37. LTU Interface Alarm History Screen  
Table 27 describes the four columns of data contained in the LTU Interface and NTU Interface Alarm History  
screens. If no alarm has occurred since the last alarms were cleared, the message "No alarms reported" displays  
on the appropriate line for each alarm.  
Table 27. LTU Interface and NTU Interface Alarm History Data  
Column  
Description  
Alarm  
First  
Type of alarm: LOS, LFA, AIS, RAI, and LOC  
Date and time the alarm first occurred  
Last  
Date and time the alarm last occurred  
Count  
Number of times the alarm has occurred since the alarms were last cleared  
(a) Not available on Nx64k serial data port units.  
54  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
Viewing Status  
HDSL Span Performance History Screens  
At the History menu (Figure 34), type 1 to select the History HDSL Span 1 menu (Figure 38).  
Figure 38. History HDSL Span 1 Menu  
The History HDSL Span 1 menu contains three viewing options:  
24 Hour History  
7 Day History  
Alarm History  
HDSL Span 1 24 Hour History Screen  
At the History HDSL Span 1 menu (Figure 38), type H to select the 24 Hour History screen for HDSL  
Span 1 (Figure 39).  
Figure 39. 24 Hour History Screen for HDSL Span 1  
UTU-701 and ETU-751 List 1  
August 9, 2002  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Viewing Status  
700-701-100-02  
The 24 Hour History screen for HDSL Span 1 contains three columns of data that show (from left to right) the:  
Starting time of each 15-minute interval.  
Number of ES/UAS at the LTU end of the HDSL span (LTU-1) for each interval. A dash (-) represents a count  
of zero.  
Number of ES/UAS at the NTU end of the HDSL span (NTU-1) for each interval. A dash (-) represents a  
count of zero.  
The entire display consists of six screens, each showing sixteen 15-minute intervals (4 hours) of performance  
history.  
Type CTRL + R or CTRL + C to display the previous or next screen in the sequence, respectively. Press the or  
key to scroll the screen up or down by one line, respectively.  
7 Day HDSL Span 1 Performance History Screens  
At the History HDSL Span 1 menu (Figure 38), type D to select the 7 Day History status screen for HDSL  
Span 1 (Figure 40).  
Figure 40. 7 Day History Status Screen for HDSL Span 1  
Each HDSL Span 7-Day History screen contains three columns of data showing (from left to right) the:  
date of each completed day within the 7-day interval  
number of ES/UAS at the LTU end of the HDSL span (LTU-1) for each interval. A dash (-) represents a count  
of zero  
number of ES/UAS at the NTU end of the HDSL span (NTU-1) for each interval. A dash (-) represents a count  
of zero  
56  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
700-701-100-02  
Viewing Status  
HDSL Span 1 Alarm History Screens  
At the History HDSL Span 1 menu (Figure 38), type A to select the Alarm History status screen for HDSL  
Span 1 (Figure 41).  
Figure 41. Alarm History Status Screen for HDSL Span 1  
Table 28 describes the four columns of data contained in each HDSL Span Alarm History screen.  
Table 28. HDSL Span Alarm History Data  
Column  
Description  
Alarm  
Type of alarm: MAR1 (Margin Span 1), ES1 (Errored Seconds Span 1), LOSW1 (Loss  
of Sync Word Span 1), PFO1 (a) (Power Feed Open Span 1), PFS1 (a) (Power Feed Short  
Span 1)  
First  
Date and time the alarm first occurred  
Last  
Date and time the alarm last occurred  
Count  
Number of times the alarm has occurred since the alarms were last cleared  
(a) Not supported. These units do not supply power to other units.  
If no alarm has occurred since the last alarms were cleared, the message "No alarms reported" displays on the  
appropriate line for each alarm.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Viewing Status  
700-701-100-02  
Clear History Screens  
Use the following options to clear the 24 Hour, 7 Day, or Alarm History status screens:  
Clr 24 Hr Hist: clears all of the 24-hour history error counters  
Clr 7 Day Hist: clears all of the 7-day history error counters  
Clr Alarm Hist: clears all alarm history logs  
To clear the status screens:  
1Select the alarm history option to be cleared with the and keys, then press ENTER . The following confirmation  
message displays:  
ALL(24-HOUR,or7DAY,orALARM)HISTORIESWILLBECLEARED.CONTINUE(Y/N)?  
2Do one of the following:  
Type N to cancel the operation.  
Type Y to clear the screen. Typing Y displays the following confirmation message:  
24-HOURHISTORIESCLEARED  
INVENTORY SCREEN  
The Inventory screen permits tracking of the system's inventory, service, and revision state. Table 29 on page 59  
describes the fields displayed in each Inventory screen. Type I to display the Inventory screen (Figure 42).  
Figure 42. Inventory Screen  
58  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
Viewing Status  
Table 29. Inventory Screen Data  
Field  
Description  
Displays the configuration of the LTU or NTU circuit.  
Network Diagram  
Product  
Displays the model numbers of the LTU, NTU, and any doubler units that comprise the channel.  
Displays the LTU, NTU, and doubler unit list numbers, which identify the particular unit versions.  
Displays the LTU, NTU, and doubler unit hardware configuration level.  
List #  
H/W Cfg  
Serial #  
Displays the unique serial number of the LTU, NTU and any doubler units for inventory and service  
tracking.  
Manuf  
Displays the date the LTU, NTU, and any doubler units were manufactured.  
Displays the number of days the LTU, NTU, and any doubler units have been in operation.  
Displays the ADC part number of the firmware.  
Days Op  
SW Part #  
Chksum  
S/W Rev  
SW Date  
Displays the checksum of the LTU, NTU, and doubler unit proms.  
Displays the currently installed firmware version level of the LTU, NTU and any doubler units.  
Displays the date that the firmware was released.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Testing  
700-701-100-02  
TESTING  
From the main console screen (Figure 29), type T to display the Test menu from which you can set and run  
loopback and BER tests (Figure 43).  
Figure 43. Test Menu Screen  
Table 30 on page 61 lists the Test menu options. Table 31 lists the fields displayed in the Bit Error Rate (BER)  
section of the test menu.  
Loopbacks remain active until the timeout elapses or the configuration changes. The loopback location and status  
are indicated on the network diagram portion of the test menu, with "@@]"characters as follows:  
Flashing reverse video for active loopbacks  
Solid reverse video for disabled loopbacks  
Front panel loopback (LPBK) LED indications are described in Table 4 on page 6. See page 19 for a description  
of loopbacks.  
60  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
Testing  
Table 30. Test Menu Options  
Operating Option  
Default Setting  
Network Diagram  
Lpbk Dir  
Shows the loopback position and direction when the loopback is enabled and active.  
Selects one of three loopback direction modes:  
OFF  
No loopbacks are active.  
NETWORK  
The loopback selected in Loopback Position is directed toward the network equipment connected to  
the LTU.  
CUSTOMER  
The loopback selected in Loopback Position is directed toward the customer's equipment connected  
to the NTU.  
Lpbk Loop(s)  
NONE  
Selects the loops used in the loopback test:  
Option not available with single-pair HDSL card.  
Selects the possible loopback positions:  
Lpbk Position  
NONE  
Option not available with single-pair HDSL card.  
Selects one of three loopback timeouts:  
Lpbk Timeout  
NONE  
Disables automatic timeout cancellation of all loopbacks.  
Automatically cancels any loopback 20 minutes after initiation.  
Automatically cancels any loopback 120 minutes after initiation.  
20  
120  
Table 31. BER Section of Test Menu  
Field  
Description  
BER Test  
STOP  
Selects the state of the BER test.  
Terminates the current test and resumes normal transmission of user payload. Prior BER tests are  
maintained for reference on the screen. STOP must be selected to terminate the BER test prior to exiting  
the screen.  
RESTART  
Begins BER test. This disrupts user payload traffic and inserts a pseudo-random bit sequence (PRBS)  
at the LTU toward the NTU. The actual pattern used is a 2x1015 pattern as defined by reselecting this  
option (pressing the ENTER key) while the test is running. This entry reinitiates the BER values and  
restarts the test.  
Det. Status  
NOT ACTIVE  
SYNCING  
IN SYNC  
Displays the current status of the BER detector at the LTU.  
Displays while the BER is not running.  
Indicates that the BER qualification period is in progress (128 received bits are compared to the PRBS).  
Indicates that the BER test is in progress. The BER meter accumulates errors once per test interval (16  
seconds). In a high bit error environment the test interval is shortened and the BER meter is updated  
every second.  
Test Time  
Bit Errors  
Displays the elapsed test time for the BER test.  
Displays the number of bits received that did not match the PRBS pattern. This field is updated every  
30 seconds, with a maximum value of 255 per update.  
BER  
Displays the Bit Error Rate computer for the current test. This field is updated very 16 seconds, as is  
displayed in exponential form. The lowest positive displayable value is 1x10-11  
.
UTU-701 and ETU-751 List 1  
August 9, 2002  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Firmware Download Utility  
700-701-100-02  
FIRMWARE DOWNLOAD UTILITY  
The Firmware Download Utility is a separate program and is not available from the console  
screen menus.  
This section describes the ETSI Firmware Download utility and how to use it to upgrade the line and desktop unit  
firmware. The ETSI Firmware Download utility is a program you can run on a PC to download new firmware to  
the LTU or NTU by connecting a standard RS-232 interface cable to the unit front panel V.24 console port. When  
using the ETSI Firmware Download utility, follow these rules:  
Make sure the destination unit where the new firmware is to be upgraded is correct before pressing the  
ENTER key.  
Do not disconnect the interface cable during the download process.  
Do not abort the download once it has started.  
Figure 44 shows the menu for the ETSI Firmware Download Utility. The upper area of the ETSI Firmware  
Download Utility menu displays the configuration options, and the lower area displays messages during the  
download process.  
Figure 44. ETSI Firmware Download Utility Menu  
62  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
700-701-100-02  
Firmware Download Utility  
Initiate the Download and Navigate the Menus  
To initiate the download process, go to the DOS prompt and type: dnl. Table 32 describes ETSI Firmware User  
Selectable Download Menu Options.  
Table 32. ETSI Firmware User Selectable Download Menu Options  
Option  
Description  
PORT  
Provides support for two communication ports:  
COM1 at Hex 3F8  
COM2 at HEX 2F8  
SPEED  
Supports Standard (9600 bit/s), Medium (19.2K kbps), Fast (38.4 kbps), Faster  
(57.6 kbps) and TURBO (115.2 kbps) speeds. The number of data bits is fixed at 8,  
with no parity and 1 stop bit.  
DESTINATION  
The destination can be set to one of the following:  
LOCAL (unit connected to the maintenance terminal)  
LTU (LTU unit)  
NTU (NTU unit)  
NTU2 (NTU2 unit, in case of point-to-multipoint download)  
REGENERATOR1  
REGENERATOR2  
FILE NAME(a)  
Enter the firmware download file name.  
(a) FILE NAME can be changed by pressing the DEL key, then typing the new file name. Once in the FILE NAME field,  
the download setup can be aborted only by typing CTRL + C . After typing the new file name, press the ENTER  
key to start the download sequence.  
Table 33 describes how to navigate within the ETSI Firmware Download menu.  
Table 33. Navigating the ETSI Firmware Download Menu  
Keystroke  
Result  
PAGE UP or PAGE DOWN  
Change a setting, with the exception of the FILE NAME setting.  
Move from field to field.  
and  
Abort setup and returns to the DOS prompt.  
Start the download process.  
ESC  
ENTER  
Download progress messages include:  
program size  
download time  
program checksum  
line-unit response  
time out message (posted if the line unit does not response within five seconds; when this occurs, the  
download operation is aborted).  
While downloading, the line or desktop unit front panel LEDs all light, then a binary count sequence indicates  
progress. When downloading is complete, the unit resets.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Reference Information  
700-701-100-02  
REFERENCE INFORMATION  
This section lists the pinouts for the ETU-751C rear panel connectors and the ECA-80x connector adapters.  
ETU-751C CONNECTOR PINOUTS  
The pinouts for the ETU-751C rear panel connectors are listed in Table 34 and Table 35.  
Table 34. D9F HDSL Line Connector Pinouts  
Pin (a)  
Signal  
Description  
4
9
1
6
HDSL_RING_A  
HDSL_TIP_A  
HDSL_RING_B  
HDSL_TIP_B  
HDSL Loop 1 (Ring)  
HDSL Loop 1 (Tip)  
HDSL Loop 2 (Ring)  
HDSL Loop 2 (Tip)  
(a) All other pins are not used. Pins 1 and 6 not used on single-pair HDSL cards.  
Table 35. D25F Data Port Connector Pinouts  
Pin (a)  
Signal Name  
V.35  
V.36  
X.21  
DCE Input/Output  
7
Signal Ground  
Send Data  
SG  
SG  
SG  
2
14  
SD_A  
SD_B  
SD_A  
SD_B  
T_A  
T_B  
Input  
3
Receive Data  
RD_A  
RD_B  
RD_A  
RD_B  
R_A  
R_B  
Output  
Output  
Output  
Input  
16  
15  
12  
Send Timing  
SCT_A  
SCT_B  
ST_A  
ST_B  
S_A  
S_B  
17  
9
Receive Timing  
Terminal Timing  
Clear to Send  
RCT_A  
RCT_B  
RT_A  
RT_B  
not used  
24  
11  
SCTE_A  
SCTE_B  
TT_A  
TT_B  
TT_A  
TT_B  
5
13  
CTS  
CTS  
not used  
Output  
Output  
Output  
6
22  
Data Set Ready  
Received Line Signal Detect  
DSR  
RLSD  
DSR  
RLSD  
not used  
8
10  
I_A  
I_B  
25  
Test Mode  
TM  
TM  
not used  
Output  
Input  
4
19  
Request to Send  
RTS  
RTS  
C_A  
C_B  
20  
23  
Data Terminal Ready  
DTR  
DTR  
not used  
Input  
18  
21  
Local Loopback  
LL  
LL  
not used  
not used  
Input  
Input  
Remote Loopback  
RL  
RL  
(a) All other pins are not used.  
64  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
700-701-100-02  
Reference Information  
ECA-800 CONNECTOR ADAPTER (DB25M TO M34F FOR V.35)  
The ECA-800 connector adapter (Figure 45) converts the DB25F data port connector on the desktop unit rear  
panel to a standard V.35 34-pin female connector. Table 36 lists the ECA-800 pinouts.  
A
E
B
F
D
J
C
H
M
S
1
14  
25  
L
K
N
R
P
T
U
V
X
W
Y
Z
AA  
BB  
FF  
LL  
CC  
HH  
MM  
DD  
JJ  
NN  
EE  
KK  
13  
Figure 45. ECA-800 DB25M to M34F (V.35) Connector Adapter, Part Number 150-1470-01  
Table 36. ECA-800 DB25M to M34F (V.35) Connector Adapter Pinouts  
DB25M Connector  
Signal  
M34F (V.35) Connector  
Signal  
Pin  
Pin  
Shield  
Send Data A  
1
2
A
P
Frame ground  
Send Data A  
Send Data B  
14  
3
S
Send Data B  
Receive Data A  
R
T
Receive Data A  
Receive Data B  
16  
4
Receive Data B  
Request to Send A  
Clear to Send A  
Data Set Ready A  
Data Terminal Ready A  
Signal Ground  
C
Request to Send  
5
D
E
Clear to Send  
6
Data Set Ready  
20  
7
H
B
Data Terminal Ready  
Signal Ground  
Received Line Signal Detect A  
Send Timing A  
8
F
Received Line Signal Detect  
Serial Clock Transmit A  
Serial Clock Transmit B  
Serial Clock Receive A  
Serial Clock Receive B  
Serial Clock Transmit External A  
Serial Clock Transmit External B  
Local Loopback  
15  
12  
17  
9
Y
Send Timing B  
AA  
V
Receive Timing A  
Receive Timing B  
Terminal Timing A  
Terminal Timing B  
Local Loopback  
Remote Loopback  
Test Mode  
X
24  
11  
18  
21  
25  
U
W
L
N
NN  
Remote Loopback  
Test Mode  
UTU-701 and ETU-751 List 1  
August 9, 2002  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Reference Information  
700-701-100-02  
ECA-801 CONNECTOR ADAPTER (DB25M TO DB15F FOR X.21)  
The ECA-801 connector adapter (Figure 46) converts the DB25F data port connector on the desktop unit rear  
panel to a standard X.21 15-pin female connector. Table 37 lists the ECA-801 pinouts.  
1
14  
1
9
15  
8
25  
13  
Figure 46. ECA-801 D25M to DB15F (X.21) Connector Adapter, Part Number 150-1470-01  
Table 37. ECA-801 DB25M to DB15F (X.21) Connector Adapter Pinouts  
DB25M Connector  
Signal  
DB15F (X.21) Connector  
Signal  
Pin  
Pin  
Send Data A  
Send Data B  
2
14  
3
2
9
Send Data A  
Send Data B  
Receive Data A  
4
Receive Data A  
Receive Data B  
16  
4
11  
3
Receive Data B  
Request to Send A  
Request to Send B  
Signal Ground  
Control A  
19  
7
10  
8
Control B  
Signal Ground  
Receive Line Signal Detect A  
Receive Line Signal Detect B  
Receive Timing A  
Receive Timing B  
Terminal Timing A  
Terminal Timing B  
8
5
Indication A  
10  
17  
9
12  
6
Indication B  
Signal Element Timing A  
Signal Element Timing B  
DTE Signal Element Timing A  
DTE Signal Element Timing A  
13  
1
24  
11  
15  
ECA-802 CONNECTOR ADAPTER (DB9M TO RJ-45)  
The ECA-802 connector adapter (Figure 47) converts the DB9F HDSL line connector on the desktop unit rear  
panel to an RJ-45 modular style connector. Table 38 lists the ECA-802 pinouts.  
66  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
700-701-100-02  
Reference Information  
1
5
8
1
6
9
Figure 47. ECA-802 DB9M to RJ-45 Connector Adapter, Part Number 150-1472-01  
Table 38. ECA-802 DB9M to RJ-45 Connector Adapter Pinouts  
DB9M Connector  
Signal  
RJ-45 Connector  
Signal  
Pin (a) Pin (a)  
HDSL Loop 1 (Ring)  
HDSL Loop 1 (Tip)  
HDSL Loop 2 (Ring)  
HDSL Loop 2 (Tip)  
4
9
1
6
1
2
4
5
HDSL Loop 1 (Ring)  
HDSL Loop 1 (Tip)  
HDSL Loop 2 (Ring)  
HDSL Loop 2 (Tip)  
(a) Pins 1, 6, 4, and 5 not used on single-pair HDSL cards.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Reference Information  
700-701-100-02  
ECA-804 CONNECTOR ADAPTER (DB9M TO FOUR-POSITION  
TERMINAL BLOCK)  
The ECA-804 connector adapter (Figure 48) converts the DB9F HDSL line connector on the desktop unit rear  
panel to a four-position terminal-block style connector. Table 39 lists the ECA-804 pinouts.  
1
1
6
2
3
4
9
5
Figure 48. ECA-804 DB9M to Four-Position Terminal Block Connector Adapter, Part Number 150-1474-01  
Table 39. ECA-804 DB9M to Four-Position Terminal Block Connector Adapter Pinouts  
Four-Position Terminal Block  
D9M Connector  
Signal  
Signal  
Pin (a)  
Pin (a)  
HDSL Loop 1 (Ring)  
HDSL Loop 1 (Tip)  
HDSL Loop 2 (Ring)  
HDSL Loop 2 (Tip)  
1
2
3
4
4
9
1
6
HDSL Loop 1 (Ring)  
HDSL Loop 1 (Tip)  
HDSL Loop 2 (Ring)  
HDSL Loop 2 (Tip)  
(a) Pins 3, 4, 1, and 6 not used on single-pair HDSL cards.  
68  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
700-701-100-02  
Product Support  
PRODUCT SUPPORT  
ADC Customer Service Group provides expert pre-sales and post-sales support and training for all its products.  
Technical support is available 24 hours a day, 7 days a week by contacting the ADC Technical Assistance Center  
at the number listed below.  
Quotation Proposals  
Sales Assistance  
800.366.3891 ext. 73000 (USA and  
Canada) or  
Ordering and Delivery  
General Product Information  
952.917.3000  
Fax: 952.917.3237  
Complete Solutions (from concept to  
installation)  
Systems Integration  
800.366.3891, ext. 73000 (USA and  
Canada) or  
Network Design and Integration Testing  
System Turn-Up and Testing  
952.917.3000  
Network Monitoring (upstream or downstream)  
Power Monitoring and Remote Surveillance  
Service/Maintenance Agreements  
Systems Operation  
Technical Information  
ADC Technical Assistance Center  
800.638.0031 (USA and Canada) or  
714.730.3222  
Fax: 714.730.2400  
System/Network Configuration  
Product Specification and Application  
Training (product-specific)  
Installation and Operation Assistance  
Troubleshooting and Repair/Field Assistance  
Online Technical Support  
Online Technical Publications  
Product Return Department  
800.366.3891 ext. 73748 (USA and  
Canada) or  
ADC Return Material Authorization (RMA)  
number and instructions must be obtained  
before returning products.  
952.917.3748  
Fax: 952.917.3237  
Email: repair&[email protected]  
All 800 lines are toll-free in the USA and Canada.  
UTU-701 and ETU-751 List 1  
August 9, 2002  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Abbreviations  
700-701-100-02  
ABBREVIATIONS  
AIS  
Alarm Indication Signal  
Alarm  
LL  
Local Loopback  
Local  
ALM  
ANSI  
AWG  
BER  
C
LOC  
LOC  
LOSW  
LPBK  
LTU  
M34F  
MAR  
Mbps  
MHz  
mm  
American National Standards Institute  
American Wire Gage  
Bit Error Rate  
Loss of Clock  
Loss of Sync Word  
Loopback  
Centigrade  
Line Termination Unit  
M-type 34-pin Female Connector  
Margin  
COM  
CRC  
CTS  
D15F  
D25F  
D9F  
dB  
Communication  
Cyclic Redundancy Check  
Clear To Send  
Megabits per second  
Megahertz  
D-type 15-pin Female Connector  
D-type 25-pin Female Connector  
D-type 9-pin Female Connector  
Decibel  
millimeter  
NC  
Normally Closed  
Normally Open  
Network Termination Unit  
NO  
DCE  
Det  
Data Communications Equipment  
Detector  
NTU  
NVRAM Non-volatile Random Access Memory  
dnl  
Download  
Nx64k  
Number (N) of 64 kbps DS0 time slots  
mapped to a data port.  
DS0  
Digital Service, Level 0 (64 kbps)  
Data Set Ready  
Op  
Operation  
DSR  
DTE  
DTR  
EMC  
EMI  
EMS  
EMU  
ES  
PFO  
PFS  
Power Feed Open  
Power Feed Short  
pulse per minute  
Pseudorandom Bit Sequence  
Random Access Memory  
Remote  
Data Terminal Equipment  
Data Terminal Ready  
ppm  
PRBS  
RAM  
REM  
RL  
Electromagnetic Compliance  
Electromagnetic Interference  
Exchange Office Management Shelf  
Exchange Office Management Unit  
Errored Second  
Remote Loopback  
Received Line Signal Detector  
Ready to Send  
RLSD  
RTS  
S/W  
ETR  
ETSI  
ETSI Technical Report  
European Telecommunications Standards  
Institute  
Software  
ETU  
EXT  
H/W  
HDSL  
Hz  
ETSI Termination Unit  
External  
SD  
Transmit Data  
ST  
Send Timing  
Hardware  
SYNC  
TM  
TT  
Synchronization  
Test Mode  
High-bit-rate Digital Subscriber Line  
Hertz  
Terminal Timing  
Unavailable Seconds  
Universal Termination Unit  
Volts  
I/F  
Interface  
UAS  
UTU  
V
ID  
Identification  
INT  
kbps  
km  
Internal  
kilobytes per second  
kilometers  
Vdc  
VT100  
W
Volts direct current  
A terminal-emulation system  
Watts  
LED  
Light Emitting Diode  
70  
August 9, 2002  
UTU-701 and ETU-751 List 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
CERTIFICATION AND WARRANTY  
DIRECTIVE EN300 386-2 COMPLIANCE  
To indicate compliance with EN300 386-2, these products have been affixed with the CE mark.  
LIMITED WARRANTY  
ADC DSL Systems, Incorporated (“ADC”) warrants that, for a period of sixty (60) months from the date of  
shipment, the hardware portion of its products will be free of material defects and faulty workmanship under  
normal use. ADC's obligation, under this warranty, is limited to replacing or repairing, at ADC's option, any such  
hardware product which is returned during the 60-month warranty period per ADC's instructions and which  
product is confirmed by ADC not to comply with the foregoing warranty.  
ADC warrants that, for a period of 90 days from the date of purchase, the software furnished with its products will  
operate substantially in accordance with the ADC published specifications and documentation for such software.  
ADC’s entire liability for software that does not comply with the foregoing warranty and is reported to ADC  
during the 90-day warranty period is, at ADC’s option, either (a) return of the price paid or (b) repair or replace  
of the software. ADC also warrants that, for a period of thirty (30) days from the date of purchase, the media on  
which software is stored will be free from material defects under normal use. ADC will replace defective media  
at no charge if it is returned to ADC during the 30-day warranty period along with proof of the date of shipment.  
The transportation charges for shipment of returned products to ADC will be prepaid by the Buyer. ADC will pay  
transportation charges for shipment of replacement products to Buyer, unless no trouble is found (NTF), in which  
case the Buyer will pay transportation charges.  
ADC may use reconditioned parts for such repair or replacement. This warranty does not apply to any product  
which has been repaired, worked upon, or altered by persons not authorized by ADC or in ADC's sole judgment  
has been subjected to misuse, accident, fire or other casualty, or operation beyond its design range.  
Repaired products have a 90-day warranty, or until the end of the original warranty period—whichever period is  
greater.  
ADC DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT  
LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE, WITH RESPECT TO ITS PRODUCTS AND ANY ACCOMPANYING WRITTEN MATERIALS.  
FURTHER, ADC DOES NOT WARRANT THAT SOFTWARE WILL BE FREE FROM BUGS OR THAT ITS  
USE WILL BE UNINTERRUPTED OR REGARDING THE USE, OR THE RESULTS OF THE USE, OF THE  
SOFTWARE IN TERMS OF CORRECTNESS, ACCURACY, RELIABILITY OR OTHERWISE.  
MODIFICATIONS  
Any changes or modifications made to these devices that are not expressly approved by ADC DSL Systems voids  
the user's warranty.  
All wiring external to the product should follow local wiring codes.  
For technical assistance, refer to “Product Support” on page 20.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
ADC DSL Systems, Inc.  
14402 Franklin Avenue  
Tustin, CA 92780-7013  
Tel: 714.832.9922  
Fax: 714.832.9924  
Technical Assistance  
ISO 9001/TL 9000  
DOCUMENT: 700-701-100-02  
´,JE¶1l¨  
DNV Certification, Inc.  
REGISTERED FIRM  
1242371  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3D Connexion Dishwasher Y2L User Manual
ADC Network Card ACE 142S 142V User Manual
AEG Ventilation Hood DK 1160 User Manual
AEG Washer LN 79680A3 User Manual
Airlink Printer APSUSB1 User Manual
Aiwa DVD Player XD DV380U User Manual
A T International Cordless Telephone E5812B User Manual
Audiovox Car Stereo System Car Stereo System User Manual
Bakers Pride Oven Kitchen Entertainment Center PHC70 MPINS User Manual
BC Speakers Speaker System DE800 User Manual