User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Important Notice
All statements, technical information, and recommendations related to 3M’s products
are based on information believed to be reliable, but the accuracy or completeness is
not guaranteed. Before using this product, you must evaluate it and determine if it is
suitable for your intended application. You assume all risks and liability associated with
such use. Any statements related to the product which are not contained in 3M’s
current publications, or any contrary statements contained on your purchase order shall
have no force or effect unless expressly set forth in a written agreement signed by an
authorized officer of 3M.
Technical Support
For technical support, call 1-866-631-1656 or email [email protected]
© 2012 3M. All Rights Reserved.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Copyright, Trademarks and Properties Notices
3M and the 3M logo are trademarks of 3M Company. Used under license in Canada.
MHL and the MHL logo are a trademark, registered trademark or service mark of MHL,
LLC in the United States and/or other countries.
High Definition Multimedia Interface (HDMI) is a registered trademark of HDMI
Licensing, LLC in the United States and/or other countries.
iPad is a trademark of Apple, Inc., registered in the U.S. and other countries.
DLP and the DLP® logo are trademarks of Texas Instruments.
DisplayPort, Certified DisplayPort, Dual-mode DisplayPort and VESA are registered
Trademarks of the Video Electronics Standards Association.
microSD™ and the microSD logo are Trademarks of the SD Card Association.
All other product names are trademarks, registered trademarks, or servicemarks of
their respective owners.
4
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Intended Use Statement
The 3M™ Mobile Projector MP300 is designed to operate with the 3M Power Adapter
and an HDMI® or MHL™ enabled device in environments that meet these conditions.
•
•
•
0° to 35°C (32° to 95°F)
10–80% RH (without condensation)
0–1829 m (0–6000 feet) above sea level
Continued exposure to smoke, grease, oil and other airborne contaminants can affect
the operation or performance of the projector. Use of this product in adverse conditions
will void the product warranty.
Safety Information
Please read, understand, and follow all safety information contained in these
instructions prior to the use of this projector. Retain these instructions for future
reference.
Explanation of Signal Word Consequences
Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury and/or
property damage.
Warning:
Indicates a potentially hazardous situation, which, if not
avoided, may result in minor or moderate injury and/or
property damage.
Caution:
© 2012 3M. All Rights Reserved.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Warning
To reduce the risk associated with hazardous voltage, fire, explosion, battery
leakage or overheating which may cause serious injury or death:
•
Do not leave the product in a car or in direct sunlight for extended periods of time.
(-20 C to 70 C)
•
•
•
•
•
•
Do not disassemble/ modify the product or attempt to remove the battery.
Do not attempt to service this product. Contact manufacturer.
Do not use the product in water or a damp environment.
Do not use a damaged product, cables or power adapter.
Charge with 3M power adapter only.
Do not dispose of the remote control battery by incineration or fire.
To reduce the risks associated with driver distraction:
•
Do not shine light into the driver's eyes.
•
Driver should not operate product while driving.
To reduce the risks associated with choking:
Keep the remote control, all cables, and small parts away from young children.
To reduce the risks associated with hearing loss:
•
•
Be sure to read earphone manufacturer's instructions with respect to volume level.
•
User is responsible to set a safe volume level.
To reduce the risk of injury to small children:
•
Supervise the use of this product by small children.
•
Keep small children away from the projector lens when the product is powered on.
6
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Caution
To reduce the risk associated with environmental disposal hazards which may
cause minor or moderate injury:
•
Dispose of the product and accessories in accordance with the federal, state, local
or regional laws which cover the disposal of electrical and electronic waste.
To reduce the risks associated with projector LED bright light:
Do not look directly into the projector lens or shine it into anyone’s eyes.
To reduce the risks associated with tripping and falling:
Position the cables so that they are not a tripping hazard.
•
•
To reduce the risk of muscle strain which if not avoided may cause minor or
moderate injury:
•
Do not mount or position the projector in awkward viewing positions.
SAVE THESE INSTRUCTIONS
© 2012 3M. All Rights Reserved.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Introduction
Thank You
This product has been produced in accordance with 3M quality and safety standards to
provide smooth and trouble-free use in the years to come. For optimum performance,
please follow the operating instructions carefully.
Product Features
Quick, seamless visual presentations are critical in today’s business world, however,
projectors often act as a roadblock to accomplishing this fundamental task. Many
professionals are opting for lugging around a huge projector, renting a projector at a
substantial cost, or opting for no projector at all and eating the cost of printing color
presentations. Say goodbye to these frustrations. Say hello to simple, plug-n-play
projection. Introducing the 3M™ Mobile Projector MP300
•
Ultra portable – small enough to put into a coat pocket with up to 3.5 hour battery
life
•
•
•
Quick set up – turn on and present in seconds
Built in speaker
Bright enough for a variety of settings – 60 lumens (not designed for brightly lit
environments)
•
•
Beautiful design – intuitive plug-n-play interface
HDMI/MHL – mirror* your iPad®, tablet, laptop and smartphone device
8
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Package Contents
The 3M™ Mobile Projector MP300 comes with the following items. If you are missing
any of these items please contact 3M.
1 3M Mobile Projector MP300
2 HDMI Cable
3 Power Adapter
4 Outlet Adapters (4)
5 Remote Control
6 Product Warranty and Safety Guide and
Quick Start Guide
© 2012 3M. All Rights Reserved.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Parts of Projector
Front-Top View
1
2
3
Button Panel - Turn on and control projector
Speaker
Air Vent - Do not block the air vents while projector is operating or cooling
down. This will cause projector to overheat and automatically turn off.
Projection Lens
4
5
Focus Wheel - Adjusts the image sharpness
10
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Bottom-Rear View
6
7
Tripod Mount
Air Vents - Do not block fans or vents while projector is operating or
cooling down. This will cause projector to overheat and automatically
turn off.
8
9
DC Input - Powers the projector or charges the battery using the 3M
power supply.
Audio Output – Allows you use earphones or external speakers instead
of the built-in speaker.
10 Service Port
11 Projector Reset Button
12 HDMI/MHL Port – Receives HDMI and MHL signal from compatible
video devices
13 Cover
© 2012 3M. All Rights Reserved.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Projector Button Panel
1
2
3
4
5
6
7
1
2
Volume Down Button -Turns down speaker or audio out output. Down
and Left Arrow for projector menu system.
Volume Up Button - Turns up speaker or audio out output. Up and Right
Arrow for projector menu system.
3
4
Information Button – Opens the projector information window.
Remote Control Receiver - Accepts commands from 3M remote
control.
5
6
7
Menu Button – Opens the projector menu
Power Button - Powers the projector on and off.
Status Light – Provides the projector's power and charging status.
12
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Parts of Remote Control
1
1 Infrared LED – Transmit remote control commands to
projector.
2
2 Arrow Buttons – Moves the selector or cursor in
projector menu or the MHL enabled device's
screen.
3 Standby – Turns the projector's lamp off or on.
4 OK Button – Press to select or click an item.
5 Back Button – Press to open previous screen on the
MHL enabled device.
6 Rewind – Rewinds video and music during playback.
7 Volume Down - Decreases the audio volume.
8 Lamp ON/OFF – Turn off the projector lamp while
keeping projector power on.
9
3
10
4
5
6
7
11
12
13
14
8
15
16
9 Menu Button – Press to open the projector menu.
10 Home Button – Press to open the Home screen on
the MHL enabled device.
11 Fast Forward – Advances video music playback.
12 Play/Pause - Start or Pause video or music
playback.
13 Volume Up – Increases the audio volume.
14 Info Button – Opens the projector information
window and is the select button when the
projector menu is open.
15 Options – View more options on the MHL-enabled
device.
© 2012 3M. All Rights Reserved.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Getting Started
In the following section, charge the projector's battery, and turn on the projector.
Power Adapter
The power adapter is used to charge the battery or power the projector. There are four
outlet adapters. When the power adapter is first shipped, it is fitted with a blank outlet
adapter. This must be removed before installing an outlet adapter.
Installing an Outlet Adapter
1 Press the "PUSH" button on the underside of the power adapter.
2 Remove the blank outlet adapter by sliding up.
3 Select the outlet adapter that will plug into your wall outlet and align to the power
adapter.
4 Slide the outlet adapter down until it clicks into place.
14
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Charging the Battery
The rechargeable battery in 3M Mobile Projector MP300 gives you up to three hours of
battery life while in ECO lamp mode. When the battery needs to be charged, the status
indicator LED starts flashing red. The battery should be fully charged before using the
projector for the first time.
Charge the battery:
1 Turn the projector power off.
2 Connect the power adapter to the projector’s DC input.
3 Connect the other end of the power adapter to the electrical outlet.
4 The status indicator will change to amber while the battery is charging.
5 Allow three hours to fully charge the battery. When charging is complete, the status
indicator will flash green.
Battery Charging Notes:
•
If the projector power is off, allow three hours for the battery to fully recharge. If the
projector power is on, the battery will take longer to charge.
•
The battery has a lifespan and ages every time it is fully charged and discharged.
The battery will gradually lose charge capacity as it ages.
Battery Maintenance Tips:
•
Charge and discharge the battery by turning on the projector at least once a
month.
•
•
When storing the projector for more than a month, store it at 50% charge.
The battery is at 50% charge when half of the battery icon is white.
© 2012 3M. All Rights Reserved.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
•
Do not store the projector when it is fully discharged. It will lose the ability to
charge.
Turning on and off the Projector
Press the power button on the projector to turn on the projector. After the projector is
powered on for the first time, you use the power button the projector or remote control
to turn the projector on and off.
MHL-enabled device such as a smartphone receives power from the projector. You can
turn off the projector's lamp without turning off the MHL-enabled device. The Lamp On
and Off button is on the remote control.
Turning the Projector On: Press the power button on the projector or remote control.
Note: Some devices that receive their power from the projector and might take 30
seconds or more to become ready to use.
Turning the Projector Off: Press and hold the power button until the projector turns
off.
Turning the Lamp On and Off: You can turn the projector's lamp off without turning
the projector off by pressing the lamp button on the remote control. The projector lamp
will turn off immediately while the cooling fans continue to run.
16
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
While the projector's lamp is off, the status indicator remains green. This tells you that
the lamp is off but the projector is still on. Press Lamp On/Off button on the remote
again and the lamp will turn on.
Important Note: Even though the lamp is off, the projector continues to use a power
and generate heat. The projector will turn off if it overheats or looses battery power.
You prevent the projector from turn off by keeping the air vents clear and plugging it
into the power adapter.
Status Indicator lights
The status indicator light provides information about the projector’s power, battery, and
error status.
Status Indicator Light
Solid amber
Solid green
Meaning
The projector is charging.
The projector is on.
Flashing green
Flashing amber
Flashing red
The projector is finished charging.
The projector has overheated.
The battery power is low.
© 2012 3M. All Rights Reserved.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Setting up the Projector
The projector is quick and easy to setup. You can project the image onto most flat
surfaces. This section covers positioning the projector, focusing the image, and
adjusting the brightness and contrast settings.
Choosing a surface
The best surface for the image is a flat, white surface. In most cases, lightly textured
walls do not affect the image quality. Alternatively, a color wall will change the hue of
the image. You can either point the projector at a wall or projector screen or a ceiling.
Placing the projector
Place the projector on a stable surface. You can place the projector on its foot or on the
rear cover. You can even attach the projector to a tripod.
18
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Attaching the Projector to Tripod (Optional Accessory)
On the bottom of the projector, you will find a tripod socket (1/4"-20) that fits most
standard camera tripods, including the optional 3M tripod (78-6972-0073-7).
© 2012 3M. All Rights Reserved.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Distance versus Image Size
The 3M Mobile Projector can project an image from 10 inches (22.1 cm) to 80 inches
(265.7 cm) diagonal. As you increase the size of the projected image, you will need to
decrease (darken) the ambient room lighting. Refer to the chart for associated
dimensions.
Image Size
Distance
Diagonal
Width
Height
10 in (25.4 cm)
20 in (50.8 cm)
35 in (88.9 cm)
45 in (114.3 cm)
55 in (139.7 cm)
65 in (165.1 cm)
76 in (193.0 cm)
80 in (203.2 cm)
8 3/4 in (22.1 cm)
17 3/8 in (44.3 cm)
30 1/2 in (77.5 cm)
39 1/4 in (99.6 cm)
47 in (121.8 cm)
4 7/8 in (12.4 cm)
9 3/4 in (24.9 cm)
17 1/8 in (43.6 cm)
22 in (56.0 cm)
26 in (68.4 cm)
31 7/8 in (80.9 cm)
37 1/4 in (94.6 cm)
39 1/4 in (99.6 cm)
16 5/8 in (42.2 cm)
33 1/4 in (84.3 cm)
58 1/8 in (147.6 cm)
74 3/4 in (189.7 cm)
91 1/4 in (231.9 cm)
107 7/8 in (274.1 cm)
126 1/8 in (320.4 cm)
132 3/4 in (337.3 cm)
56 5/8 in (143.9 cm)
66 1/4 in (168.3 cm)
69 3/4 in (177.1 cm)
20
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Adjusting the Focus
After you find a place for the projector, rotate the focus wheel to sharpen the image.
Adjusting the Brightness and Contrast settings
You can use the projector brightness and contrast settings to adjust the image based
on the lighting conditions.
Adjusting the Brightness
Adjust the brightness setting until details in the dark levels of the image appear. If you
are unable to see the detail, try reducing the image size or the lighting in the room.
Using the Remote: Press the menu button at the top-right of the remote control; press
Ok button; press the right arrow to increase the brightness or the left arrow button to
decrease the brightness. You can exit the menu by pressing the menu button twice.
Using the Projector Keypad: Press the menu button; press the Info button; press the
volume down to decrease the brightness and volume up to increase the brightness. You
can exit the menu by pressing the menu button twice.
© 2012 3M. All Rights Reserved.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Adjusting Contrast
Adjust the contrast setting until details in the bright level of the image appear.
Using the Remote: Press the menu button at the top-right of the remote control; press
the down arrow; press Ok button; press the right arrow to increase the contrast
brightness or the left arrow button to decrease the contrast. You can exit the menu by
pressing the menu button twice.
Using the Projector Keypad: Press the menu button; press the Info button; press the
volume down to decrease the brightness and volume up to increase the brightness. You
can exit the menu by pressing the menu button twice.
22
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Volume Up/ Down
The volume buttons on the projector and the remote control adjust the sound from the
speakers or the audio output. Additionally, MHL enabled devices plugged into the
projector can adjust the projector volume level using the device's remote.
Display Volume Level: Press the volume up or down button to display the volume
slider.
Increase or Decrease Volume: Press the volume up button to increase the audio
volume or press the volume down to decrease the audio volume.
Quickly Increase or Decrease Volume: Press and hold the volume up button to
quickly increase the audio volume or press and hold the volume down to quickly
decrease or mute the audio volume.
Mute the Sound: Press the volume up and down on the projector at the same time or
press the mute button on the remote control.
© 2012 3M. All Rights Reserved.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Remote Control
The 3M remote control controls the projector, or any MHL enabled device plugged into
the projector.
Remove Protective Film
Before you can begin using the remote control, you must remove the protective film
from the battery compartment. Remove the film as shown below.
Using the Remote
When using the remote control, point the remote control's infrared transmitter at the
receiver on the projector. Sometimes you can control the projector by pointing the
remote at the surface in front, beside, or above the projector. The remote control's
range is up to 20 feet.
Note: Sun light and some indoor lighting may reduce the range of the remote control.
24
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Replacing the Battery in the Remote Control
Replace the battery in the remote control with a CR2025 battery.
1. Remove the battery and battery
tray by holding latch toward the
center of the tray and then pull the
tray out of the remote control.
latch
2. Place the new battery into the tray
and orientating the battery positive
size (+) as indicated on the tray.
3. Finally, slide the tray into the
remote control.
© 2012 3M. All Rights Reserved.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Connecting to other devices
The 3M Mobile Projector connects to other digital video devices such as tablets,
computers, smartphones, and dvd players. Compatible device will most likely have one
of the following video output connector:
Description
HDMI®
Connector on
Device
Cable Connector
Example Devices
DVD Players, BluRay
DVD Players, Game
Consoles, Set-Top
Boxes, Computers
Portable Digital Media
Player, Computers
Mini-HDMI
Micro HDMI
Tablet and
Smartphones
Micro USB
(MHL)
Tablets and
Smartphones
Display
Port®
Computers
26
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Notes:
1. Not all devices with a microUSB port are MHL enabled devices. Check the
device's specification before purchasing a MHL cable.
2. Some products have proprietary connectors not shown above (such as the
dock connector on the Apple iPad or iPhone.) Check for a digital video
accessory adapters or cable from the manufacture.
Connecting to the Projector
The HDMI/MHL port on the projector can accept a standard HDMI connector. Once you
plug the cable into the port, you can close the cover.
1. Open Cover
DC in
2. Plug in HDMI cable
© 2012 3M. All Rights Reserved.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
3. Route the cable
and close the cover
28
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Connecting to a MHL Device
The 3M Mobile Projector supports MHL through the HDMI port. While playing video and
audio from your MHL compatible device, the 3M Mobile Projector charges your device.
Additionally, you can control your device using the projector's remote control. The
standard MHL cable has a microUSB connector on one end and a HDMI connector on
the other.
1 Connect the HDMI end of cable to the projector’s HDMI/MHL input.
2 Connect the other end of the cable to the device’s microUSB port (MHL).
Notes:
1. MHL cable not included. This cable is also known as a "passive MHL cable".
2. Please reference the device's user manual and specification for compatibility
with MHL.
© 2012 3M. All Rights Reserved.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Connecting to a HDMI Video Device
The 3M Mobile Projector can playback video and audio from a device with HDMI output.
1 Connect the HDMI end of the cable to the projector’s HDMI/MHL input.
2 Connect the other end of the cable to the video device’s audio and video outputs.
Notes:
1. HDMI not included.
2. Please reference the device's user manual and specification for compatibility with
HDMI.
30
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Connecting to a Display Port® Video Device
The 3M Mobile Projector can play video and audio from your Display Port compatible
device. You will need a Display Port to HDMI Adapter or cable.
1 Connect DisplayPort to HDMI adapter into device.
2 Connect the HDMI end of the cable to the projector’s HDMI/MHL input.
3 Connect the other end of the cable into the HDMI port on the adapter.
Notes:
1. The DisplayPort adapter and HDMI Cable are not included.
2. Please reference the device's user manual and specification for compatibility with
Display Port.
© 2012 3M. All Rights Reserved.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Menu
The projector's menu allows you to adjust the brightness, contrast, lamp power, and
picture mode. The following section description each setting and how the navigate the
menu system.
1
2
3
4
5
6
Item Menu Item
Description
1
2
3
Brightness
Contrast
Lamp Power
Adjusts the dark levels of the image.
Adjusts the bright levels of the image.
Switches between standard and eco mode. Eco
mode extends the battery life by reducing the
power and brightness of the lamp.
- Eco
- Normal (Default)
4
Image
Changes the image orientation
32
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Orientation
- Normal (Default)
- Upside down
- Upside down and mirrored
- Mirrored
5
6
Picture Mode
Changes the image based on the input type:
video or computer.
Since the buttons on the projector have multiple
purposes, the navigation help provides a key for
the buttons on the projector.
Navigation
Help
Using the menu
You can navigate the menu using the buttons on the projector or the remote control.
Open the Projector Menu: Press the Menu button.
Select a Menu Item:
•
Projector Control Panel: Press the Volume Up and Down to move the
selector.
•
Remote Control: Press the up or down arrows
Adjust Menu Item:
•
Projector Control Panel: Press the Info button and press Volume Up and
Down to adjust the setting.
© 2012 3M. All Rights Reserved.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
•
Remote Control: Press the Ok or right arrow and then press right or left
button to adjust the setting.
Return to Menu Item Selection: Press the Menu button or press OK on the remote
control.
On-Screen Icons
One of the these icons will appear when the projector does not detect an input, detects
an MHL device but no input, or the video resolution is not supported.
- No input detected
- video resolution is not supported
- A MHL device is detected but the video signal is not detected.
Information Screen
Press the Info button on the remote or projector to open the information screen. The
information shows you the if the sound is muted or not, the lamp power level and
battery power level.
34
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Reset Button
The reset button restarts the projector in the event the projector stops responding.
Reset the projector by disconnecting the video input and power, and then press the
reset button using an uncoiled paper clip. This will turn off the projector and allow you
to turn the projector on again.
Cleaning the Projector
1 Turn off the projector and disconnect power and other cables.
2 Use a soft cloth, such as the 3M™ High Performance Cleaning Cloth, to wipe off
dust. If the dust is difficult to remove, dampen the cloth with clean water and then wipe
the projector clean. Then use a clean cloth to dry the projector.
Important Note: Do not use cleaning chemicals or solvents to clean the projector.
Cleaning chemicals and solvents may cause the plastic parts to discolor.
© 2012 3M. All Rights Reserved.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Troubleshooting
The Power Adapter and Charging the Battery
I do not see where to insert the outlet clip into the power adapter.
•
There is a blank clip inserted into the power adapter when it is shipped. Remove
the blank clip which covers the power adapter contacts. Now install an outlet clip.
I do not see an amber light when I plug the power adapter into the projector.
•
Make sure the power outlet is working.
•
Make sure the connector from the power adapter is plugged into the "DC In" on
the projector and not the headphone jack.
•
When fully charged, the LED indicator will flash green.
Installing the HDMI or MHL cable into the Projector
The HDMI or MHL cable will not insert into the projector.
•
There may be a dust cap on the end of the connector. Remove it before inserting
connector into the projector.
•
When you insert the connector, make sure the connector orientated correctly.
The cover hits the cable when I close the cover.
36
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
•
There is a cutout on the bottom corner of the cover for the cable to exit. Route the
cable down and to the right then close the cover.
The cover does not close properly.
•
There is tab on the bottom corner of the cover. Make sure the tab inserts into the
groove on the projector and the rest of the cover snaps into place.
Turning the Projector On or Off
The projector will not turn on.
•
The battery is not charged. Plug the power adapter into the projector and try again.
The projector button panel is on but the projector is not projecting an image.
•
The video source (such as the DVD Player) is outputting a black image. First, try
disconnecting the HDMI video cable. Do you see the 3M™ logo screen? If not, try
turning off the projector and turning it on again. If you still do not see a 3M Logo
screen while the status indicator is green, contact 3M for additional support.
The Lamp is off. Press the Lamp ON/Off button on the remote control.
•
The remote control will not turn on the projector.
•
When the projector is new and never been turned on, you must use the power
button on the projector. Now you can turn on the projector by pressing the power
button on the projector or the remote control.
© 2012 3M. All Rights Reserved.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
The status indicator on the projector flashes red.
The projector's battery needs to be charged.
•
Setting Up the Projector
The projector falls over when I place it on its rear cover.
•
The cover may not be seated properly. There is a tongue on the bottom corner of
the cover. Insert the tongue into the groove on the projector and the rest of the
cover will snap into place.
The image is tinted or discolored.
•
The wall or surface you're projecting onto is colored. Try projecting onto a white
wall or surface.
•
The lens may be dirty. Use a dry cotton swab to clean it off.
Focusing the Image
The image is blurry.
•
•
•
Use the focus wheel on the side of the projector (next to the lens) to sharpen the
image.
Reduce the input resolution. The native resolution of projector is 480p. Therefore,
resolutions greater that 720p may appear blurry.
If you are closer to the projected image than the projector, you might be seeing the
individual pixels that make up the image. Reduce the size of the image or move
away from the image.
The image is too dim.
Reduce the image size and/ or decrease (darken) the room lighting.
•
38
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
The image seems bright enough but there are no details in the dark shadows.
•
Open the projector menu and increase brightness setting and then decrease the
contrast slightly.
The image seems bright enough but there are no details in the highlights.
Open the projector menu and decrease contrast.
•
Adjusting the Volume
There is no audio coming out of the speaker
•
•
•
Turn up the volume or turn off mute.
Turn up the volume on the external speakers.
There may be a moment of silence in the show you are watching.
Using the Remote Control
The remote control does not work.
•
Remove the plastic film that is in-between the battery and the remote control.
•
•
Replace the battery. The battery size is a CR 2025.
The remote control is out of range of the projector. The remote control's range is
up to 20 feet.
© 2012 3M. All Rights Reserved.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
•
Sunlight or lighting in the room can interfere with the projector's reception of the
remote control's signal.
40
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Product Specification
Description
Specification
Imager
Technology
Size
TI DLP
0.3"
Resolution
Aspect Ratio
WVGA 854 x 480 Pixels
16:9
Projection Distance
Image Size
Throw Ratio (Diagonal: Distance)
16 5/8 in. – 199 1/4 in. (42.2– 506 cm)
10 in. – 80 in. Diagonal (25.4– 203.2 cm)
1:1.66
Lens Offset
Inputs
Audio Outputs
100%
DC-in, HDMI (MHL)
1x2 Watt Speaker, Headphone Jack
Video Compatibility
Video Resolutions
NTSC, PAL
480p,576p, 720p,1080i
Dimensions
4.33 x 4.21 x 2 in. (110 x 107 x 51.6mm)
Weight
Tripod Socket
≤ 15.9 oz (≤ 450 g)
¼" - 20
Operating Conditions
Temperature
32 – 95°F (0-35°C)
Range
Humidity Range
Altitude Range
10–80% RH without condensation
Sea Level to 1,829 m (6000')
11.5 Watts (Standard Lamp Mode)
7.0 Watts (Eco Lamp Mode)
Power Consumption
© 2012 3M. All Rights Reserved.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Battery Specification
Type
Rated Capacity
Rechargeable Lithium-Ion Battery
7.4 V, 2600mAh
Video and Audio Support
The following list is the resolutions are supported by the projector. The projector
displays a WVGA (854x480) image. The best input resolution for the projector is 480p.
Other higher resolution will be reduced to 480p resolution.
Video Support
Description
480p
Resolution (width x height)
640x480p
720x480p
720x480p
720x576p
Refresh Rate
59.94/60 Hz
59.94/60 Hz
59.94/60 Hz
50 Hz
50 Hz
59.94/60 Hz
50 Hz
Aspect Ratio
4:3
4:3
16:9
4:3
16:9
16:9
16:9
16:9
16:9
576p
720p
1080i
720x576p
1280x720p
1280x720p
1920x1080i
1440x1080i
59.94/60 Hz
50 Hz
Audio Support
Audio Format: Linear PCM,
Number of Channels: 2
Sampling Frequency: 32, 44.1, and 48 kHz
Number of Bits Per Sample: 16, 20 or 24 bits
42
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Accessory List
Call 1-866-831-1656 to order 3M accessories.
© 2012 3M. All Rights Reserved.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Limited Warranty
The 3M™ Mobile Projector MP300 (the “3M Product”) is warranted to be free from
defects in material or manufacture for a period of 90 days from the date or purchase. If
the product does not conform to the warranty within the warranty period, 3M’s
exclusive obligation is to repair, replace or refund the purchase price of the non-
conforming product. To the extent permitted by law, 3M will not be liable for indirect,
incidental, special or consequential damages, irrespective of the legal theory asserted.
If the product needs service, please call 1-866-631-1656. For the detailed terms and
us at 1-866-631-1656 or [email protected]
44
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Regulatory Notices
FCC STATEMENT - CLASS B
This equipment has been tested and found to comply with the limits for aClass B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC
equipment provided that the following conditions are met. If the cables include a EMI
ferrite core, attach the ferrite core end of the cable to the projector. Use the cables
which are included with the projector or specified.
© 2012 3M. All Rights Reserved.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
Note: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CE Statement
ElectroMagnectic Compatibility Statement: Meets 2004/108/EC Directive
Low Voltage Directive: Meets 2006-95-EC Directive.
WEEE Statement
The following information is only for EU-members States: The mark shown to the right
is in compliance with Waste Electrical and Electronic Equipment Directive 2002/96/EC
(WEEE). The mark indicates the requirement NOT to dispose the equipment as unsorted
municipal waste, but use the return and collection systems according to local law.
RoHS Statement
Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic
Equipment (known as “RoHS”), 2011/65/EU of the European Parliament and of the
Council and the Regulation 1907/2006 (known as “REACH”) relating to “Substances of
Very High Concern (“SVHC’s”), the European Union’s Directive 94/62/EC relating to
packaging, the U.S. Lacey Act and other similar laws (“Substance Laws”). Product will
not contain substances in excess of permitted concentration values established by
Substance Laws unless the applicable specifications specifically permit that substance
in a higher concentration value. Without limiting the forgoing, substances in the product
will not exceed the following maximum concentration values in any homogeneous
material (“Restricted Values”): (a) 0.1% (by weight) for each of lead, mercury,
46
© 2012 3M. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3M™ Mobile Projector MP300
hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or
(b) 0.01% (by weight) for cadmium.
© 2012 3M. All Rights Reserved.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|