321 Studios Coffeemaker 4DX 33 User Manual

EPSON Endeavor 4SX/25, 4DX/33, and 4DX2/50

To select low speed, press the Ctrl, Alt,

and - keys simultaneously. To select

high speed, press the Ctrl, Alt, and + keys

simultaneously. (Use the - or + key on the

numeric keypad.)

hard disk

access light

diskette

drive

(SPEED) light

4MB RAM standard on a SIMM;

expandable using 1MB, 4MB, or 16MB

SIMMs to 32MB (maximum); SIMMs must

be 36-bit, fast-page mode type with 70ns

(or faster) access speed

Memory

128KB system BIOS, video BIOS, and

SETUP code located in EPROM on main

system board

ROM

hay for hard

tape, CD-ROM, or other drive

diskette,

Video RAM

512KB or 1MB DRAM on main system

board; 512KB configuration expandable

to 1MB

110/220 VAC switch

option card slots

Shadow RAM

Cache

Supports shadowing of system and video

BIOS ROM into RAM

8KB of internal cache (built into the

microprocessor)

Math

coprocessor

On 4DX/ 33 and 4DX2/ 50 systems, math

coprocessor built into the microprocessor;

optional 487 upgrade available for 4SX/ 25

system

Real-time clock, calendar, and CMOS

RAM socketed on main system board with

built-in battery backup

Clock/ calendar

power keyboard

inlet port

serial serial

port 1 port 2

VGA

monitor

parallel

mouse

port

Controllers

Video

Cirrus® VGA controller on main system

board; provides resolutions up to

1024 x 768

Computer Specifications

D i s k e t t e

Controller on main system board supports

up to two diskette drives or one diskette

drive and one tape drive

CPU and Memory

32-bit CPU

4SX/25: Intel® i486SX, 25 MHz

microprocessor; can be replaced with

optional 487SX/ 25 or ODP486-25

processor

Hard disk

Interface on main system board supports

up to two IDE hard disk drives with

built-in controlIers

4DX/ 33: Intel i486DX, 33 MHz

microprocessor; can be replaced with

optional ODP486-33 OverDrive processor

Interfaces

Monitor

VGA interface built into main system

board for analog or multifrequency VGA

monitor; 15-pin, D-shell connector

4DX2/ 50: Intel i486DX2, 50 MHZ

microprocessor

Parallel

Serial

One standard &bit parallel, uni- or bi-

directional interface built into main system

board; I/ O address selectable through

SETUP; 25-pin, D-shell connector

System speed

High and low speeds available; high speed

depends on CPU (25 MHz, 33 MHz, or

50 MHz), low speed is simulated 8 MHz

speed; speed selection through keyboard

command; 0 wait state memory access at

highspeed

Two RS-232C, programmable,

asynchronous interfaces built into main

system board; 9-pin, D-shell connectors

4/1/93

EPSON Endeavor-1

Download from Www.Somanuals.com. All Manuals Search And Download.

EPSON Endeavor 4SX/25, 4DX/33, and 4DX2/50

PS/ 2 compatible keyboard interface built

into main system board; num lock setting

selectable through SETUP; 6-pin, mini DIN

connector

Keyboard

SETUP

Stored in ROM; accessible by pressing the

Delete key at the SETUP prompt during boot

Program

Video Modes

PS/ 2 compatible mouse interface built into

main system board; 6-pin, mini DIN

connector

Memory required

512KB

Mouse

Mode

VGA

Resolution

Colors

6 4 0 x 4 8 0

8 0 0 x 6 0 0

1 0 2 4 x 7 6 8

512KB

2 5 6

1 M B

32, 768*

65, 536*

16, 777, 216**

Four 16-bit (or 8-bit) I/ O expansion slots,

ISA compatible, 8 MHz bus speed; three

slots accommodate any size card,

bottom slot can hold reduced size card

(4.4 inch/ l 10 mm)

Option slots

1 M B

512KB

2 5 6

512KB

1 M B

32, 768*

65, 536*

1 M B

Speaker

Internal

512KB

1 M B

2 5 6

Alternate VGA

IBM compatible VGA pass-through

interface built into main system board;

26-pin connector

** TrueColor

* Hi-Color

Power Supply

Mass Storage

Three drives maximum (two horizontal

mounts and one vertical mount),

configurable using the following:

145 Watt, fan cooled

Type

Input ranges

98 to 132 VAC and 180 to 264 VAC,

switch-selectable voltage

Horizontal

mounts

Up to two externally-accessible,

half-height horizontal mounts; each

horizontal bay can accommodate one

form factor diskette, tape,

CD-ROM, or other drive, or one

form factor hard disk, diskette, tape,

CD-ROM, or other drive with

mounting frames attached

+5 VDC at 18 Amps, +12 VDC at 4.0 Amps,

-5 VDC at 0.3 Amps, -12 VDC at 0.3 Amps

Maximum

outputs

Frequency

Cables

47 to 63 Hz

Two to main system board; four to mass

storage devices

Option Slot Power Limits

One internal third- or half-height vertical

mount; vertical bay can accommodate one

form factor hard disk or other

drive

Vertical

mount

+12 Volts -5 Volts and -12 Volts

Maximum current +5 Volts

For each slot

For all four slots

7 Amps

16 Amos

1.5 Amps

3 Amos

0.5 Amps

Diskette drives

5.25-inch, 1.2MB (high-density)

3.5-inch, 1.44MB (high-density)

5.25-inch, 360KB (double-density)

3.5-inch, 720KB (doubledensity)

Combo 5.25-inch, 1.2MB/ 3.5-inch, 1.44MB

(highdensity); combines two diskette

drives in one

Environmental Requirements

Hard disk

drives

form factor hard disk drive(s),

third- or half-height size; the first mounted

vertically, second mounted horizontally

Other devices

Half-height tape drive, CD-ROM drive, or

other storage device;

form factor

form factor with

mounting frames attached

Physical Characteristics

Width

14.8 inches (370 mm)

Keyboard

Detachable, two-position height; 101 or 102

sculpted keys; country-dependent main

typewriter keyboard; numeric / cursor

control keypad; four-key cursor control

keypad; 12 function keys

16.5 inches (412 mm)

4.8 inches (120 mm)

Depth

Height

16.7 lb (7.5 kg) with one diskette drive and

one hard disk, without keyboard

Weight

EPSON Endeavor-2

4/1/93

Download from Www.Somanuals.com. All Manuals Search And Download.

EPSON Endeavor 49SX/25, 40X/33, and 4DX2/50

Serial Port Connectors (CN4 and CN5)

Major Subassemblies

main system option card connector board

board

(option board riser card)

Serial Port Connector Pin Assignments

Keyboard Connector (CN3) and

Mouse Connector (CN2)

speaker drive

drive bays

Although the keyboard and mouse connectors are physically

identical, they cannot be used interchangeably.

Keyboard and Mouse Connector Pin Assignments

Connector Pin Assignments

Pin Signal

Data

Reserved

Ground

+5 VDC (fused)

Clock

Reserved

Parallel Port Connector (CN6)

pin 1

pin 13

VGA Port Connector (CN7)

pin 5

pin 10

pin 15

pin 1

pin 14

pin 25

pin 6

Parallel Port Connector Pin Assignments

pin 11

VGA Port Connector Pin Assignments

EPSON Endeavor-4

4/1/93

Download from Www.Somanuals.com. All Manuals Search And Download.

EPSON Endeavor 4SX/25, 4DX/33, and 4DX2/50

System I/O Address Map

VGA Feature Connector (CN8)

VGA Feature Connector Pin Assignments

‘Active low logic

DMA Assignments

Level

Assigned device

Spare (&bit)

FDD controller (&bit)

Spare (8-bit)

Spare (16-bit)

DMA0

DMA1

DMA2

DMA3

DMA5

DMA6

DMA7

Hardware Interrupts

IRQ no.

IRQ0

IRQ1

Function

Timer output

Keyboard

IRQ3

IRQ4

IRQ5

IRQ6

Serial port 2

Serial port 1

Available (parallel port 2)

FDD controller

4/1/93

EPSON Endeavor-5

Download from Www.Somanuals.com. All Manuals Search And Download.

EPSON Endeavor 4SX/25, 4DX/33, and 4DX2/50

Jumper Settings

If the computer’s microprocessor is a FQFP type, it is surface-

mounted on the main system board. To add an OverDrive

processor, install it in the empty OverDrive socket and

disable the original microprocessor by setting jumper J23 to

position 2-3. Also make sure J10, J11, and J12 are set correctly.

Processor Speed Jumper Settings

You need to change the processor speed jumper settings if

rocessor with a 33 MHz processor.

you replace a 25 MHz

J13

J15

Processor Chips

If you have the 4SX/ 25 or 4DX/ 33 system, you can install an

p rocessor on the main system board to

Intel OverDrive

effectively double the internal clock speed of the computer’s

microprocessor. Alternatively, for the 4SX/ 25, you can install

the 487SX/ 25 microprocessor with built-in math coprocessor.

OverDrive Processors

OverDrive processor

ODP486-25

ODP486-33

System

4SX/25

40X/33

Adapter, CMOS, and PQFP jumper Settings

Jumper

setting

Jumper

number

Function

SIMM Installation

Off*

Supports CGA adapters

Supports monochrome, EGA, MCGA, and

VGA adapters

J5***

The computer comes with 4MB of memory installed in a

SIMM socket. To increase the amount of memory in the

computer up to 32MB, you can install 36-bit, fast-page mode

SIMMs that operate at an access speed of 70ns or faster, with

a capacity of 1MB, 4MB, or 16MB.

1-2*

2-3

Enables the built-in VGA display adapter

Disables the built-in VGA display adapter so

you can use a display adapter on an option

card in the computer as the primary adapter

Returns CMOS RAM to the factory settings

Retains SETUP program settings

J7***

Off’

1-2*

The following table shows the possible SIMM configurations;

do not install memory in any other configuration. Make sure

that both SIMMs operate at the same speed.

Reserved

J18

J23**

1-2*

2-3

1-2

2-3

Gate A20 reset (standard setting for windows)

Keyboard reset

Enables the WFP SX/25 processor

Disables the PQFP SX/25 processor

SIMM Configurations

Total memory

4MB *

4MB

5MB

SIMM

4MB

* Factory setting

** Factory setting depends on type of processor on system board

** Two pin jumpers

4MB

1MB

4MB

1MB

4MB

16MB

8MB

Processor Jumper Settings

16MB

17MB

20MB

32MB

16MB

1MB

16MB

4MB

16MB

1MB

16MB

4MB

16MB

You need to change the processor jumper settings if you

install a new processor chip. The settings for J10, J11, and J12

must correspond to the type of chip installed.

Standard memory

4/1/93

EPSON Endeavor-6

Download from Www.Somanuals.com. All Manuals Search And Download.

EPSON Endeavor 4SX/25, 40X/33, and 4DX2/50

Hard Disk Drive Types (continued)

Video Memory

If the computer has 512KB of video memory, you can install

four 256K x 4 bit, 70ns, 20-pin DRAM DIP (Dual Inline

Package) chips to increase the video memory to 1MB. The

following table lists which DRAM DIP chips you can install

on the main system board.

Supported DRAM Chips

Part number

Manufacturer

Mitsubishi®

Toshiba®

M5M44256BP-7

TC514256AP-70

MT4C4256-70

Micron®

Hard Disk Drive Types

The table below lists types of hard disk drives you can use in

the computer. Check this table and your hard disk manual to

find the correct type number(s) for the hard disk drive(s)

installed in the computer. You need to enter the type

number(s) when you set the hard disk drive configuration in

the SETUP program.

If the computer has an Epson 120MB or 240MB hard disk

drive, select the appropriate type number from the table

below when you run the SETUP program.

Hard Disk Drive Types

Epson Hard Disk Drive Types

Type number

Epson hard disk drive

120MB

240MB

Installation/Support Tips

Power

The computer has an input voltage selection switch on the

back panel to select between 115V, for USA and Canadian

use, and 230V, for use in other countries.

Mouse and Keyboard

When connecting the mouse and keyboard to the computer,

be careful to plug them into the proper ports. Although the

ports are physically identical, they are not interchangeable,

and damage may occur to the main system board if you plug

the connectors into the wrong ports

Installing Diskette Drives

Make sure that the drive type has been correctly selected in

the SETUP program.

4/1/93

EPSON Endeavor-7

Download from Www.Somanuals.com. All Manuals Search And Download.

EPSON Endeavor 4SX/25, 4DX/33, and 4DX2/50

Installing Hard Disk Drives

Information Reference List

It is recommended that a 16-bit, AT-type hard disk

controller be used if you are installing a drive that cannot

Engineering Change Notices

use the embedded IDE interface. If you install

non-IDE

None.

hard disk drive and controller card, you need to use the

SETUP program to disable the built-in IDE hard disk drive

interface.

Technical Information Bulletins

None.

When installing a hard disk drive, see the hard disk drive

type tables on page 7 and use the SETUP program to select

the correct type number for the drive. You can select a

type number that matches the parameters for the drive or

a type number with parameters having lesser values, as

long as they do not exceed the maximum capacity (in MB)

of the drive. If there is no match for the drive, you can

select a user-defined drive type (48 or 49) and enter the

drive’s exact parameters.

Product Support Bulletins

None.