Motorola D1000 Series
For D1001, D1002, D1003 and D1004
Digital Cordless Phone
Warning
Use only rechargeable batteries.
This User Guide provides you with all the information
you need to get the most from your phone.
Before you make your first call you will need to set up
your phone.
Follow the simple instructions in ‘Getting Started’, on the next
few pages.
IMPORTANT
Only use the telephone line cord supplied.
This equipment is not designed for making emergency telephone calls when the power fails. Alternative
arrangements should be made for access to emergency services.
Got everything?
•
•
•
•
•
•
D1000 handset
D1000 base
User guide
2 x AAA NiMH rechargeable batteries
Mains power adapter for the base
Telephone line cord
If you have purchased a D1000 multiple pack you will also have the following additional items:
•
•
•
D1000 handset & charger
2 x AAA NiMH rechargeable batteries
Mains power adaptor for the charger
Need help?
If you have any problems setting up or using your D1000, please contact Customer Services on (65) 6841 2668.
Email: [email protected]
Alternatively, you may find the answer in the ‘Help’ section at the back of this guide.
4.6 View an entry......................................................18
4.7 Edit an entry .......................................................18
4.8 Delete an entry ...................................................18
4.9 Delete all entries.................................................19
4.10Copy phonebook to another handset .................19
4.11One touch keys ..................................................19
4.12Dial a one touch number ....................................19
4.13Store a phonebook entry as a
1. Getting started ................................................6
2. Getting to know your phone..........................9
3. Using the phone............................................14
3.1 Calls................................................................... 14
3.1.1 Make a call ............................................ 14
3.1.2 Pre-dial .................................................. 14
3.1.3 Dial one touch numbers 1 to 9 .............. 14
3.1.4 Call from the phonebook ....................... 14
3.1.5 Call from the calls list ............................ 14
3.1.6 Answer a call ......................................... 14
3.1.7 Adjust volume ....................................... 15
3.1.8 Mute ...................................................... 15
3.1.9 End a call .............................................. 15
3.1.10 Switch handset on/off ............................ 15
3.2 Intercom............................................................. 15
3.2.1 Call another handset ............................. 15
3.2.2 Transfer an external call to
one touch number ..............................................19
4.14Delete a one touch number ................................20
5. Caller display and Calls list.........................20
5.1 Calls list..............................................................20
5.1.1 View the calls list ...................................21
5.1.2 Dial from the calls list .............................21
5.1.3 Save a number from the calls list
to the phonebook ...................................21
5.1.4 Delete a calls list entry ...........................22
5.1.5 Delete entire calls list .............................22
5.2 Redial .................................................................22
5.2.1 Redial the last number ...........................22
5.2.2 View and dial a number in the
another handset .................................... 16
3.2.3 Three-party conference call .................. 16
4. Phonebook ....................................................16
4.1 View and dial phonebook entries....................... 16
4.2 Store an entry.................................................... 16
4.3 Entering names ................................................. 17
4.4 Character map................................................... 17
4.5 Enter a pause .................................................... 18
redial list .................................................22
5.2.3 Copy a redial number to the
phonebook .............................................22
5.2.4 Delete a redial list entry .........................22
5.2.5 Delete entire redial list ...........................23
4
8.3 Call barring.........................................................28
8.3.1 Switch call barring on/off .......................28
8.3.2 Set a number to be barred ....................29
8.4 Easy call.............................................................29
8.4.1 Switch easy call on/off ...........................29
8.4.2 Set the easy call number .......................29
8.4.3 Dial an easy number .............................30
8.5 Registration........................................................30
8.6 Register a handset.............................................30
8.7 Select a base .....................................................31
8.8 Unregister a handset..........................................31
8.9 PIN .....................................................................31
8.10Reset..................................................................31
8.11Default settings ..................................................32
8.12Auto prefix..........................................................32
8.13Country...............................................................32
8.14Intrusion .............................................................33
8.15ECO mode .........................................................33
6. Clock & Alarm .............................................. 23
6.1 Set date and time...............................................23
6.2 Set alarm............................................................24
6.3 Set alarm melody ...............................................24
7. Personal settings......................................... 24
7.1 Handset tones....................................................24
7.1.1 Ring volume ...........................................24
7.1.2 Ring melody ...........................................24
7.1.3 Group melody ........................................25
7.1.4 Key tones on/off .....................................25
7.1.5 First ring .................................................25
7.2 Handset name....................................................26
7.3 Auto pick up .......................................................26
7.4 Auto hang up......................................................26
7.5 Display language................................................26
7.6 Room Monitor on/off...........................................26
7.7 Room Monitor.....................................................27
7.8 Backlight on/off...................................................27
7.9 Keypad lock........................................................27
9. Help................................................................34
10. General information .....................................35
11. Wall mounting...............................................42
8. Advanced settings...................................... 28
8.1 Recall time .........................................................28
8.2 Dial mode...........................................................28
8.2.1 Temporarily switch from Pulse to
Tone dialling ..........................................28
5
If you are on a call, the line will hang up if the handset moves
out of range of the base. Move back within in range. The
handset will automatically re-connect to the base.
1. Getting started
WARNING
Do not place your D1000 in the bathroom or other humid
areas.
Setting up
IMPORTANT
Location
The base station must be plugged into the mains power at all
times. Do not connect the telephone line cord into the wall
socket until the handset is fully charged. Only use the power
and telephone cables supplied with the product.
You need to place your D1000 base within 2 metres of the
mains power socket and telephone socket so that the cables
will reach.
WHICH POWER ADAPTOR?
Make sure it is at least 1 metre away from other electrical
appliances to avoid interference. Your D1000 works by
sending radio signals between the handset and base. The
strength of the signal depends on where you place the base.
Putting it as high as possible ensures the best signal.
The power adaptor with a clear connector is for the base unit
and the power adaptor with a red colour connector is for the
charger unit.
Connecting up the base
HANDSET RANGE
The D1000 has a range of up to 300 metres outdoors when
there is a clear line of sight between the base and handset.
Any obstruction between the base and handset will reduce
the range significantly. With the base indoors and handset
either indoors or outdoors, the range will normally be up to
50 metres. Thick stone walls can severely affect the range.
SIGNAL STRENGTH
The
icon on your handset indicates when you are in
range. When out of range of the base, the screen shows
Plug the mains power cable with the clear connector into the
SEARCHING and the
flashes.
socket marked
on the underside of the base and plug
6
Getting started
the other end into the mains power wall socket and switch
the power on.
3. Place the handset on the charger to charge for at least
24 hours. When the handset is fully charged the
icon will indicate that it is fully charged.
Connecting the handset and charger (Multi-
pack only)
If you have purchased a multiple pack, this process will need
to be carried out for all handsets and chargers:
4. When the handset is fully charged after 24 hours, plug
the telephone line cord from the large base into the
telephone wall socket.
1. Plug the mains power cable with the red connector into
IMPORTANT
the socket marked
on the underside of the charger.
Warning! Use only the approved rechargeable Ni-MH battery
cells (2 x AAA Ni-MH 550mA rechargeable batteries)
supplied with your D1000. Please do not use alkaline or non
rechargeable batteries. It may cause permanent damage to
the product and void the warranty.
BATTERY LOW WARNING
If the
icon flashes in the display, you will need to
recharge the handset before you can use it again.
During charging, the icon will scroll in the display.
Once fully charged scrolling will stop.
BATTERY PERFORMANCE
In ideal conditions, fully charged batteries should give up to
10 hours talk time or up to 150 hours standby* time on a
single charge.
2. Insert the 2 x AAA NiMH batteries supplied into the
handset. Then slide the compartment cover into place.
*All talk and standby times are approximate and depend on
features selected and usage pattern.
Getting started
7
To keep your batteries in the best condition, leave the
handset off the base for a few hours at a time.
Date and time
Providing you have subscribed to your network’s Caller
Display service, the date and time is set automatically for all
handsets every time a call is received.
Running the batteries right down at least once a week will
help them last as long as possible.
If you do not have a Caller Display service you can set the
date and time manually.
The charge capacity of rechargeable batteries will reduce
with time as they wear out, giving the handset less talk/
standby time. Eventually they will need to be replaced.
Set date and time manually
After charging your handset for the first time, subsequent
charging time is about 6–8 hours a day. Batteries and
handset may become warm during charging. This is normal.
1. Press m and scroll d to CLOCK/ALARM. Press m.
Display shows DATE & TIME, then press m.
2. Enter the date using the format DD/MM e.g. 04/ 08 for 4th
Setting up your D1000
Welcome screen
August.
3. Press mand enter the time using the 24 hour format
1. WELCOME is displayed and scrolls in different languages.
Press m. The country name is shown on the display.
HH:MM, e.g. 14:45 for 2:45pm.
4. Press m to confirm or > to return to standby.
YOUR D1000 IS NOW READY FOR USE.
2. Scroll uor dto your country and press m. CONFIRM?
is displayed.
3. Press OK to confirm.
The handset and base will reset to load the correct
settings. The standby screen is then displayed and your
phone is ready to use.
You can still make and receive calls without first selecting
your country and network operator, however the Welcome
screen will re-appear until you have configured your phone
country settings.
8
Getting started
A
B
Earpiece
2. Getting to know your phone
Overview of your handset
Display
See page 10 for an overview of the display icons.
Menu key
C
D
Enter the main menu. Select the option displayed on
screen. Confirm menu option – OK is displayed on screen.
Redial / Scroll right / Clear / Mute
Open the redial list. Scroll to the right.
Delete characters on screen when entering names and
numbers.
Mute / unmute the micrBoApChKone during a call. Go back to
previous menu level –
Call log / Scroll Up / Volume up
Open the calls log.
displayed on screen.
E
F
Scroll up through lists and settings.
Increase the earpiece volume during a call.
Talk / Recall
Make or answer a call.
Use recall (R) functions.
When on an external call, press this key once to get a
fresh dial tone or to access a Call Waiting Line when
you hear the call waiting prompt signal. Press this key
again to toggle between the two calls. Also used with
switchboard / PABX services and some network
services.
G
End / Exit / Switch handset on/off
End a call.
When in a menu, go back to standby mode. Press and
hold to switch handset off (when in standby) or on.
Getting to know your phone
9
H
Phonebook / Scroll Down / Volume down
Open the phonebook.
Handset display
Scroll down through lists and menus.
Decrease the earpiece volume.
Navigator glow ring
I
Illuminates when the phone is in use. Flashes to
indicate new Voicemail.
J
* / Keypad lock
Press and hold to lock/unlock the keypad.
During a call, press and hold to switch from pulse
dialling to tone dialling.
Dial a star.
K
L
# / Ringer off / Pause
A
Display icons
Press and hold to switch handset ringer on or off.
When dialling or storing a number, press and hold to
enter a pause (P).
On when the line is in use.
Flashes when there is an incoming call.
Dial a #.
Loudspeaker key
Activate and deactivate the loudspeaker during a call.
WARNING
Flashes when you have new voicemail messages.*
Off when you have no new voicemail messages.
Handsfree activation can suddenly increase the volume
in the earpiece to a very high level. Make sure the
handset is not too close to your ear.
Flashes when you have missed calls and new
number(s) are in the Calls list.*
Phonebook is open.
M
Intercom (at least 2 handsets needed)
In standby mode, use to make an internal call.
During a call, use to transfer an external call to another
handset.
The alarm clock has been set.
Handsfree mode.
10
Getting to know your phone
Handset ringer is off.
D
Back ! displayed
Press e to go back to the previous menu option, to
Steady when the handset is registered and within
range of the base. Flashes when the handset is out
of range or searching for base.
cancel an action or to delete a character.
Overview of the base
The approximate power levels of your battery are indicated
as below:
Battery is fully charged.
Battery is partially charged.
Battery is running low.
Battery is almost empty. The battery icon will flash
and emit a warning beep every minute during call.
A
Paging key
* For this feature to work, you must subscribe to Voicemail
service or Caller ID from your network operator. A
subscription fee may be payable.
Paging is a useful way of finding lost handsets.
1. Press p on the base.
-
All handsets ring.
B
OK displayed
2. Press p again to cancel the paging call or press any
Press the m key to select and validate a setting
key on the handset to stop the paging call.
C
! " displayed
Press uor d to scroll through the options in a menu, to open
the phonebook or call list when in standby.
Getting to know your phone
11
Navigating the menus
The basic steps of navigating through the menu and on-
screen options.
1. From the standby screen, press m.
The main menu is opened.
2. Use the u or d keys to scroll through the menu.
3. Soft key options OK and BACK are displayed. Press
m to select OK and open a sub-menu or validate an
option.
Press BACK and go back to previous menu level, correct
a character or cancel an action.
4. Press > to return to standby.
If you do not press any button on the handset for 15 seconds
the display will automatically return to standby. It will also
return to standby when the handset is placed on the base or
charger.
12
Getting to know your phone
Menu map
PHONEBOOK
CLOCK/ALARM
PERSONAL SET
ADVANCED SET
NEW ENTRY
LIST ENTRY
<NAME>
DATE & TIME
SET ALARM
ALARM TONE
HANDSET TONE
RING VOLUME
RING MELODY
GROUP MELODY
KEY TONE
RECALL TIME
DIAL MODE
CALL BARRING
EASY CALL
EDIT ENTRY
DELETE ENTRY
REGISTRATION
SELECT BASE
REGIST. BASE
FIRST RING
DELETE ALL
DIRECT MEM
PB TRANSFER*
HANDSET NAME
AUTO PICK-UP
AUTO HANG-UP
LANGUAGE
UNREGISTER
PIN
RESET UNIT
PREFIX
ROOM MONITOR
BACKLIGHT
SEL. COUNTRY
INTRUSION
ECO MODE
*This option is only available if more than one D1000 handset is registered to the base.
Getting to know your phone
13
3.1.5
NOTE
Call from the calls list
3. Using the phone
3.1
Calls
You need to subscribe to your network’s Caller Line
Identification service to be able to see the caller’s number in
the calls list. See “Calls list” on page 20 for more details.
3.1.1
Make a call
1. Press <.
2. Dial the telephone number.
1. Press u to enter CALL LOG menu. You have the options
to access CALL LIST. Press m to enter CALL LIST. The
first entry in the call list is displayed.
3.1.2
Pre-dial
1. Enter the phone number (maximum 24 digits). If you
2. Scroll u or d to the entry you want.
make a mistake press e.
3. Press < to dial the number.
2. Press < to dial the phone number entered.
3.1.6
Answer a call
3.1.3
Dial one touch numbers 1 to 9
1. When the phone rings and
<or press vto answer the call via the loudspeaker.
WARNING
When the phone is ringing, avoid holding the earpiece too
close to your ear as it may damage your hearing. Handsfree
activation can suddenly increase the volume in the earpiece
to a very high level. Make sure the handset is not too close
to your ear.
flashes in the display, press
1. Press and hold a key from 1 to 9 until the number
is displayed and dialled.
-
If no number is stored, you hear a beep.
Call from the phonebook
3.1.4
1. Press d. The first entry in the phonebook is displayed.
2. Scroll u or d to the entry you want.
3. Press < to dial the number.
TIP
NOTE
Instead of scrolling to browse the phonebook entries, press
the numeric key corresponding to the first letter of the entry
you wish to locate. For example, pressing 2will show the
entries starting with A. Pressing 2 again will show the
entries starting with B, etc...
If you have subscribed to your Network’s Caller Identity
service and assigned a VIP Group to the caller’s number, the
caller’s details are displayed before the phone starts ringing
(see “Store an entry” on page 16 and “Group melody” on
page 25). You can set your phone to give the default
14
Using the phone
ringtone as soon as the call is received then once the caller’s
identity is displayed, the assigned ringtone will start. See
“First ring” on page 25.
If auto hang-up is on (see page 26) simply replace the handset
on the base to end the call. The default setting is ON.
TIP
3.1.10 Switch handset on/off
1. Press and hold > until the handset switches off.
If Auto Pick up mode (see page 26) is on, simply lift up the handset
from its base to answer the call. The default setting is On.
2. Press and hold >again to switch the handset back on.
NOTE
An incoming call has priority over other events. Whenever
there is an incoming call, other operations in progress such
as phone settings, menu navigation, etc. will be ended.
3.2
Intercom
This feature is only available when there are at least 2
registered handsets. It allows you to make internal calls,
transfer external calls from one handset to another and use
the conference option.
3.1.7
Adjust volume
1. During a call, press u or d to adjust the earpiece or
loudspeaker volume.
3.2.1
Call another handset
-
The level is shown in the handset display.
Mute
1. Press I.
3.1.8
•
If you have two handsets, the other handset is called
automatically.
Mute the microphone so that you can talk to someone else
in the room without your caller hearing you.
•
If more than two handsets are registered to the base,
their numbers are displayed, e.g. 2345*. Enter the number
of the handset you want to call or press * to ring all
handsets.
1. During a call, press e.
-
The microphone is muted.
2. Press e again to turn the microphone back on.
3.1.9 End a call
2. Press > to hang up.
1. Press >.
After you hang up, the duration the phone is off-hook is
displayed for 5 seconds.
NOTE
If the handset does not belong to D1000/1010 range, this
function may not be available.
Using the phone
15
3.2.2
1. During an external call, press I.
Your caller is put on hold.
Transfer an external call to another handset
4. Phonebook
The D1000 handset phonebook can store up to 100 names
and numbers.
-
2. Enter the number of the handset you want to call or
NOTE
press * to ring all handsets.
Numbers can be up to 24 digits long and names up to 12
characters long. Entries are stored in alphabetical order.
-
If there are only two handsets, the other handset is
called automatically.
3. When the other handset answers, announce the caller
then press > to transfer the call. If the other handset
does not answer, press Ito talk to your caller again.
4.1
View and dial phonebook entries
1. Press d. Display shows the first entry.
2. Scroll u or d to the entry you want.
Or
3.2.3
1. During an external call, press I.
Your caller is put on hold.
Three-party conference call
To search alphabetically, press dthen press the key
with the first letter of the name, e.g. if the name
begins with N, press 6 twice.
-
2. Enter the number of the handset you want to call or
-
The display shows the first entry beginning with N. If
press * to ring all handsets.
required, press u or d to scroll to the exact entry.
-
If there are only two handsets, the other handset is
called automatically.
3. Press < to dial the entry displayed.
3. When the other handset answers, announce the call
then press and hold I to connect both calls. If the
other handset does not answer, press I to talk to
your caller again.
4.2
Store an entry
1. Press m. PHONEBOOK is displayed.
2. Press m. NEW ENTRY is displayed.
4. Press > to hang up.
3. Press m. ENTER NAME is displayed.
4. Enter a name and press m.
16
Phonebook
5. Enter a number. Press m to save. Press u or d to
or
and press m to
To enter a space press 1
select NO GROUP
confirm.
,
GROUP A
,
B
C
Press eto delete a character or press and hold eto
delete all characters.
6. Press > to return to standby.
4.4
Character map
NOTE
Use the keypad to enter names and characters.
You can assign individual contacts to specific groups of your
choice. For example, Group A contains phone numbers of all
your co-workers. You can also assign a specific ring melody
to that group (see “Group melody” on page 25). You can
benefit from this feature only if you have subscribed to Caller
Line Identification service from your network provider. If it is
the case, every time someone from that group calls you, you
will hear the designated ringtone for that group.
1
2
3
4
5
6
7
8
9
0
Space
1
C
F
I
-
<
>
*
A
D
G
J
B
2
3
4
5
6
S
8
Z
\
E
H
K
N
Q
U
X
-
L
O
R
V
Y
/
M
P
T
NOTE
Cancel storing an entry by pressing > at any time during
7
?
9
#
the process.
4.3
Entering names
W
0
Use the alphanumeric keypad to enter names in the phonebook.
+
For instance to enter the name Paul
P
A
U
L
Press 7 once
Press 2 once
Press 8 twice
Press 5 three times
Phonebook
17
display the number. If there are more than 12 digits,
4.5
Enter a pause
press e again to see the rest of the number.
If your D1000 is connected to a switchboard, you may need
to enter a pause in a stored number. This gives the
switchboard time to get an outside line. A Pause is normally
stored after the switchboard access code (e.g. 9)
3. Press > to cancel the phonebook display.
4. Press > again to end the call.
1. When storing a number, press and hold # until the
display shows P. You can then continue storing the
phone number.
4.7
1. Press d.
Edit an entry
2. Scroll u or d to the entry you want to edit and press
m. EDIT ENTRY is dsplayed. Press m again.
3. Edit the name and press mto confirm. Use eto
delete characters.
4.6
View an entry
In standby:
1. Press d.
4. Press m and edit the number.
2. Enter the first letter of the name to search alphabetically
then scroll u or d to the exact entry. The name is
displayed.
5. Press m to confirm.
6. Scroll u or d to select NO GROUP
,
GROUP A
,
B
or
C
and
3. Press e to display the number. If there are more
than 12 digits, press e again to see the rest of the
number.
press m to confirm.
7. Press > to return to standby.
4.8
1. Press d.
Delete an entry
4. Press > to return to standby.
During a call:
2. Scroll to the entry you want to delete and press m.
3. Scroll d to DELETE ENTRY and press m.
4. Display shows CONFIRM?. Press m.
1. Press m twice to open the phonebook menu.
2. Enter the first letter of the name you want then scroll u
or d if necessary to the exact name. Press e to
18
Phonebook
5. Press > to return to standby.
4.11 One touch keys
The keys 1 to 9 enable one touch dialling of entries
4.9
Delete all entries
stored in the phonebook.
1. Press m twice.
4.12 Dial a one touch number
2. Scroll d to DELETE ALL and press m.
3. Display shows CONFIRM?. Press m.
4. Press > to return to standby.
1. Press and hold a number key 1 to 9.
-
The number is displayed and dialled.
2. Press > to cancel the dialling and return to standby.
4.10 Copy phonebook to another handset
1. Press m twice.
4.13 Store a phonebook entry as a one
touch number
2. Scroll d to PB TRANSFER and press m.
1. Press m twice.
3. Scroll uor dto the number of the handset you want the
2. Scroll d to DIRECT MEM and press m.
phonebook copied to. Press m.
3. Press u or d to select KEY 1 - 9 and press m. The
current entry, if any, is displayed.
On the receiving handset:
1. TRANS. FROM: HANDSET X (where X is the handset number
of the sending handset) is displayed.
4. Press m again to open the options menu.
5. Press m to ADD an entry from the phonebook.
6. Scroll u or d to the entry you want. Press m to
confirm or > to return to standby.
Press mto start the copying process.
2. When DONE! is displayed on both handsets, press >to
return to standby.
NOTE
If an entry with the same name and number is already stored
in the receiving handset, it will not be copied across.
Phonebook
19
4.14 Delete a one touch number
1. Press m twice then scroll u or d to DIRECT MEM and
press m.
5. Caller display and Calls list
If you have subscribed to Caller Line Identification (CLI), and
provided the identity of the caller is not withheld, the number
of the caller will be displayed together with the date and time
of the call (if provided by the network).
2. Scroll u or d to select KEY 1- 9
.
3. Press m to display the current entry. Press m
NOTE
again to open the options menu.
•
•
•
If the caller’s number is stored in your phonebook along
with a name, the name will also be displayed.
If the telephone number is not available for incoming
4. Scroll d to DELETE and press m.
5. Display shows CONFIRM?. Press m.
6. Press > to return to standby.
calls, the handset will display UNAVAILABLE
.
Information about incoming calls will vary by country and
network operator. Some operators may charge a
subscription for their Caller Line Identification service.
5.1
Calls list
The calls list contains details of missed and received call.
Details include the date and time of the call. Entries are
displayed in chronological order with the most recent call at
the top of the list.
NOTE
•
•
•
When the calls list is full, a new call replaces the oldest in
the list.
The received and missed calls log holds details of up to
50 calls.
If you receive more than one call from the same number,
only the most recent call is kept in the calls list.
20
Caller display and Calls list
When you have missed calls (incoming calls that you haven’t
answered) the icon will be displayed in the display on all
handsets registered to the base.
5.1.2
Dial from the calls list
1. Press u to enter the CALL LOG option menu, then press
m to enter CALL LIST. The most recent call is
displayed.
If one handset is used to view the calls log, the icon on the
other handsets continue to flash (Multipack user only).
2. Scroll u or d to the entry you want.
5.1.1
1. Press u to enter CALL LOG option menu, then press
m to enter CALL LIST
The most recent number or name if stored in the
View the calls list
3. Press < or v to dial.
5.1.3
Save a number from the calls list to the
phonebook
.
-
1. Press u then m. The most recent call is displayed.
phonebook is displayed. New calls are marked with
icon flashing.
2. Scroll u or d to the number you want.
3. Press m then scroll d to SAVE NUMBER and press
2. Scroll u or d through the calls log.
At the end of the log, you will hear a beep.
Press e to see the number. If the number has more
than 12 digits, press e to see the rest of the
number.
m.
4. Press m. ENTER NAME is displayed. Use the keypad to
enter the name.
5. Press m then the number is displayed, the user can
then edit the number if required and must press mto
save the number (even if has not been edited).
3. Press > to return to standby.
NOTE
6. Press u or d to select NO GROUP
,
GROUP A
,
B
or
C
and
The
icon stops flashing once all new calls have been
press m to confirm.
viewed.
7. Display shows CONFIRM?. Press m to confirm.
8. Press > to return to standby.
Caller display and Calls list
21
2. Press < to dial.
5.1.4
Delete a calls list entry
1. Press u. The most recent call is displayed.
2. Scroll u or d to the number you want.
5.2.2
View and dial a number in the redial list
1. Press e. The last number dialled is displayed.
If required, scroll uor dto display the number you want.
3. Press m then scroll d to DELETE and press m.
4. Display shows CONFIRM?. Press m to confirm.
5. Press > to return to standby.
2. Press < to dial the number.
5.2.3
Copy a redial number to the phonebook
1. Press e and scroll u or d to the entry you want.
2. Press m.
5.1.5
Delete entire calls list
1. Press u. The most recent call is displayed.
2. Scroll u or d to the number you want.
3. Display shows SAVE NUMBER. Press m.
4. Enter the name and press m.
3. Press mthen scroll dto DELETE ALL and press m.
4. Display shows CONFIRM?. Press m to confirm.
5. Press > to return to standby.
5. Edit the number if required and press m.
6. Press u or d to select NO GROUP
,
GROUP A
,
B
or
C
and
press m to confirm.
5.2
Redial
7. Press > to return to standby.
The D1000 lets you redial any of the last 10 numbers called.
Numbers can be up to 24 digits long.
5.2.4
Delete a redial list entry
1. Press e. Scroll u or d to display the number you
5.2.1
Redial the last number
want.
1. Press e. The last number dialled is displayed.
If the number has more than 12 digits, the display shows
! and the cursor blinks. Press eto display the rest.
If the number is stored in the Phonebook, the name is
displayed as well.
2. Press m and scroll d to DELETE then press m.
3. Display shows CONFIRM?. Press m to confirm, then
> to return to standby.
22
Caller display and Calls list
5.2.5
Delete entire redial list
6. Clock & Alarm
If you subscribe to your network’s Caller Identification service,
the time on your D1000 may be set automatically each time
you receive a call, depending on your network provider.
1. Press e then press m.
2. Scroll d to DELETE ALL and press m.
3. Display shows CONFIRM?. Press m to confirm. Press
> to return to standby.
You can also set or adjust the time using the Clock & Alarm
menu.
6.1
Set date and time
1. Press m and scroll d to CLOCK/ALARM. Press m.
Display shows DATE & TIME, then press m.
2. Enter the date using the format DD/MM e.g. 04/ 08 for 4th
August.
3. Press mand enter the time using the 24 hour format
HH:MM, e.g. 14:45 for 2:45pm.
4. Press m to confirm.
5. Press > to return to standby.
NOTE
The date and time is retained during a power failure or when
the batteries are discharged.
Clock & Alarm
23
6.2
Set alarm
7. Personal settings
1. Press m, scroll d to CLOCK/ALARM and press m.
7.1
Handset tones
2. Scroll d to SET ALARM and press m.
WARNING
3. Scroll u or d to OFF, ON ONCE or ON DAILY and press
When the phone is ringing, avoid holding the earpiece too
close to your ear as it may damage your hearing.
m.
4. If you select ON ONCE or ON DAILY, enter the time using the
24 hour format HH - MM e.g 14:45 for 2:45pm and press
m.
7.1.1
Ring volume
Choose from: Ringer Off, Low, Medium, High, Boost and
Progressive (increasing ring volume).
NOTE
5. Press > to return to standby. When the alarm goes
off, press any key to stop the ring.
NOTE
The default setting is High.
1. Press m, scroll d to PERSONAL SET and press m.
2. HANDSET TONE is displayed. Press m.
3. RING VOLUME is displayed. Press m.
4. Scroll u or d to adjust the ringer volume level.
5. Press m to save the settings.
Once the alarm is set to on, the
icon is displayed.
The alarm will ring at the medium level. ALARM ON and the
will flash on the display.
6.3
Set alarm melody
There are three alarm ringtones.
6. Press > to return to standby.
1. Press m and scroll d to CLOCK/ALARM
.
7.1.2
Ring melody
Press m.
Choose from 10 ringer melodies.
2. Scroll d to ALARM TONE and press m.
1. Press m, scroll d to PERSONAL SET and press m.
-
Melodies are played.
2. HANDSET TONE is displayed. Press m and scroll d to
3. Scroll u or dand press m.
RING MELODY. Press m.
24
Personal settings
3. Press u or d to select the ringtone.
A sample of the ringtone is played.
7.1.4
Key tones on/off
When you press a key on the handset you hear a beep. You
can switch these beeps on or off.
-
4. Press m to confirm.
1. Press m, scroll d to PERSONAL SET and press m.
5. Press > to return to standby.
2. HANDSET TONE is displayed. Press m and scroll d to
7.1.3
Group melody
KEY TONE. Press m.
To benefit from this feature, you must subscribe to the Caller
Line ldentification service.This menu enables you to select
and set the melodies to be played when there is an external
incoming call from a contact whose name is stored in your
phonebook and is part of a group. You can associate 1 ring
melody to each group. There are three phonebook groups
(Group A, B, C) available for you to organize your contacts.
Each group can be assigned a unique melody.
3. Scroll u or d to select ON or OFF
.
4. Press m to confirm.
5. Press > to return to standby.
7.1.5
First ring
Your D1000 will automatically detect the Caller identification
(Subscription dependent). If you do not wish to hear the ring
before the caller identification is displayed you can manually
set FIRST RING to OFF. The default setting is ON.
1. Press m, scroll d to PERSONAL SET and press m.
2. HANDSET TONE is displayed. Press m and scroll d to
1. Press m, scroll d to PERSONAL SET and press m.
GROUP MELODY. Press m.
2. HANDSET TONE is displayed. Press m and scroll d to
3. Scroll u or d to select: GROUP A
,
B
or C, then press
FIRST RING. Press m.
m.
4. Press u or d to select the ringtone you want for the
3. Scroll u or d to select ON or OFF
.
group and press m.
4. Press m to confirm.
5. Press > to return to standby.
5. Press > to return to standby.
Personal settings
25
7.2
Handset name
7.4
Auto hang up
Personalise your handset, with a name or location for
example Peter or Bedroom. Maximum 10 characters.
With Auto hang up switched on, you can end a call just by
replacing the handset on the base or charger. If switched off,
you have to press >to hang up. The default setting is On.
1. Press m, scroll d to PERSONAL SET and press m.
2. Scroll d to HANDSET NAME and press m. The current
1. Press m, scroll d to PERSONAL SET and press m.
name is displayed.
2. Scroll d to AUTO HANG UP. Press m.
3. Press e to delete the current name.
4. Enter the name you want – maximum 10 characters and
press m to save.
5. Press > to return to standby.
3. Scroll u or d to select ON or OFF
.
4. Press m to confirm.
5. Press > to return to standby.
7.5
Display language
7.3
Auto pick up
You can change the display language.
1. Press m, scroll d to PERSONAL SET and press m.
2. Scroll d to LANGUAGE. Press m.
3. Scroll u or d to select the language you want.
4. Press m to confirm.
With Auto pick up switched on, you can answer a call just by
lifting the handset off the base or charger. If switched off, you
will have to press < to answer a call. The default setting
is On.
1. Press m, scroll d to PERSONAL SET and press m.
5. Press > to return to standby.
2. Scroll d to AUTO PICK UP. Press m.
3. Scroll u or d to select ON or OFF
.
7.6
Room Monitor on/off
4. Press m to confirm.
Leave one handset in a room and use another handset to
hear sounds in that room.
5. Press > to return to standby.
26
Personal settings
1. Press m, scroll d to PERSONAL SET and press m.
7.8
Backlight on/off
2. Scroll d to ROOM MONITOR. Press m.
1. Press m, scroll d to PERSONAL SET and press m.
3. Press u or d to select ON or OFF
.
2. Scroll d to BACKLIGHT. Press m.
4. Press m to confirm.
3. Press u or d to select ON or OFF
.
When switched On, you can leave this handset in the room
you wish to monitor. Only the microphone is on. Anyone in
the room cannot hear you.
4. Press m to confirm.
7.9
Keypad lock
Prevent accidental dialling while carrying the handset by
locking the keypad.
7.7
Room Monitor
1. Switch a handset’s room monitor mode setting On and
1. Press and hold *.
place that handset in the room.
-
The display shows KEYS LOCKED.
2. At a second handset, press Iand enter the number
of the handset you are using as a room monitor. You can
now hear sounds coming from the room.
2. To unlock the handset, press and hold * again.
NOTE
While the keypad is locked, you can answer incoming calls
as normal.
TIP
To stop room monitoring at any time, press >.
NOTE
If you have only registered 2 handsets with the base unit, in
step 2 above Room Monitor will be automatically activated
without entering the handset number.
WARNING
This product is not intended for use as a baby safety device
and is not a substitute for adult supervision.
Personal settings
27
3. Press u or d to select TONE or PULSE
4. Press m to confirm.
.
8. Advanced settings
This setting is useful to access certain network and PABX/
switchboard services.
5. Press > to return to standby.
8.2.1
Temporarily switch from Pulse to Tone
dialling
8.1
Recall time
The default D1000 recall time is suitable for your country and
network operator. It is unlikely that you should need to
change this setting unless advised to do so.
1. Press and hold *.
The dial mode will change from Pulse to Tone for the
duration of the call.
1. Press m, scroll d to ADVANCED SET and press m.
8.3
Call barring
2. RECALL TIME is displayed. Press m.
Prevent certain numbers from being dialled from your
D1000. Store up to four specific numbers, each up to 4 digits
– for example, international or local prefixes.
3. Press u or d to select the setting you want: SHORT
,
MEDIUM LONG.
,
4. Press m to confirm.
Bypass call barring by switching the setting Off or On.
5. Press > to return to standby.
NOTE
If you switch Call barring on, BARR MODE ON will be displayed
on your screen in standby mode.
NOTE
The use of your D1000 cannot be guaranteed on all PABX.
8.3.1
Switch call barring on/off
8.2
Dial mode
1. Press m, scroll d to ADVANCED SET and press m.
The default D1000 dialling mode is suitable for your country
and network operator. It is unlikely that you should need to
change this setting unless advised to do so.
2. Scroll d to CALL BARRING. Press m.
3. Enter the master PIN (default setting 0000) and press
m.
1. Press m, scroll d to ADVANCED SET and press m.
2. Scroll d to DIAL MODE. Press m.
4. MODE is displayed. Press m.
28
Advanced settings
5. Press uor dto select ON or OFF. Press mto confirm.
3. Enter the master PIN (default setting 0000) and press
m.
6. Press > to return to standby. You can now set the
4. MODE is displayed. Press m then press u or d to
number (See below).
select ON or OFF. Press m to confirm.
8.3.2
Set a number to be barred
1. Press m, scroll d to ADVANCED SET and press m.
5. Press > to return to standby.
2. Scroll d to CALL BARRING. Press m.
NOTE
If you switch Easy call on, EASY CALL ON will be displayed on
your screen in standby mode.
3. Enter the master PIN (default setting 0000) and press
m.
To switch Easy call off again:
4. Scroll d to NUMBER. Press m.
1. Press >.
5. If necessary, scroll u or d to the next available slot.
2. OFF? is displayed. Press m to confirm.
6. Press m and enter the number or prefix you want to
8.4.2
Set the easy call number
bar. Press m to confirm.
1. Press m, scroll d to ADVANCED SET and press m.
7. Press > to return to standby.
2. Scroll d to EASY CALL. Press m.
8.4
Easy call
3. Enter the master PIN (Default setting 0000) and press
When activated, this feature allows you to dial a number by
pressing any key on your handset (except >). This feature
is very useful for access to emergency services.
m.
4. Scroll d to NUMBER. Press m.
5. Enter the number. Press m to confirm
6. Press > to return to standby.
8.4.1
Switch easy call on/off
1. Press m, scroll d to ADVANCED SET and press m.
2. Scroll d to EASY CALL. Press m.
Advanced settings
29
8.4.3
Dial an easy number
8.6
Register a handset
When an easy call number has been stored and the easy call
setting switched on, press any key (apart from >), to dial
a number.
At the base:
1. Press and hold the p button on the base station for at
least 3 seconds. The base station emits a beep when it
is ready to accept registration. You have 90 seconds in
which to register a handset.
NOTE
When easy call is switched on, you can still answer any
incoming call as normal.
At the handset:
1. Press m and scroll d to ADVANCED SET and press
8.5
Registration
m.
Up to 5 handsets can be registered to one base station.
Additional handsets must be registered to the base before
you can use them.
2. Scroll d to REGISTRATION and press m.
3. If necessary, scroll u or d to display REGIST. BASE and
press m. BASE 1 2 3 4 is displayed and the registered
base number is flashing. Enter the number of the base
on which you wish to register your handset.
•
The instructions described below apply specifically to
your D1000 handset. If you wish to register another
manufacturer’s handset, the instructions may vary. In this
case, please refer to the manufacturer of the additional
handset.
If you have only 1 base station, press 1. If you have 2
•
The Master PIN is required before you can register or
base stations, press 1 or 2, etc.
unregister handsets. The default PIN is 0000
.
4. When the display shows PIN----, enter the base PIN.
-
When the handset registers with the base, it is
assigned a handset number.
30
Advanced settings
8.7
Select a base
8.9
PIN
You can register your D1000 handset with up to 4 bases.
Once registered, you can switch between bases, for
example, bases at home and at work.
The 4-digit master PIN is used when registering or
unregistering a handset and when changing some settings
on your D1000. The default setting is 0000. You can change
this PIN for more security.
1. Press m and scroll d to ADVANCED SET and press
1. Press m, scroll d to ADVANCED SET and press m.
m.
2. Scroll d to PIN. Press m.
2. Scroll d to REGISTRATION and press m.
3. Enter the current 4 digit master PIN and press m.
3. SELECT BASE is displayed. Press m.
(Default setting 0000).
-
The available bases are displayed with the current
base number flashing.
4. Enter the new PIN and press m.
4. Enter the number of the base you want – 1,2,3 or 4 and
NOTE
press m.
Make a note of your PIN. If you forget your PIN you will
need to reset your product.
-
When the base is found you hear a beep. If not found,
the display shows UNREGISTERED
.
8.10 Reset
8.8
Unregister a handset
This will reset your D1000 to its default settings.
1. Press m and scroll d to ADVANCED SET and press
m.
1. Press m, scroll d to ADVANCED SET and press m.
2. Scroll d to RESET UNIT. Press m.
2. Scroll d to UNREGISTER and press m.
3. Enter the 4 digit master PIN and press m.
3. CONFIRM? is displayed. Press m.
-
Display shows the registered handset numbers.
NOTE
4. Scroll u or d to select the handset you want to delete
Entries stored in the phonebook are retained. After reset,
depending on your country, the welcome mode setting may
be shown on the handset display.
and press m.
-
UNREGISTERED is displayed on the handset screen.
Advanced settings
31
8.11 Default settings
8.12 Auto prefix
You can set the D1000 to detect a dialling number and
replace it with another number. The number to be detected
can be up to 5 digits long. It can be replaced with a number
up to 10 digits.
Handset name
Handset
On
Key tone
First ring
On
Auto pick up
Auto hang up
Ringer melody
Ringer volume
Earpiece volume
Phonebook
Call log
On
1. Press m, scroll d to ADVANCED SET and press m.
2. Scroll d to PREFIX. Press m.
On
Melody 1
High
3
3. DETECT DIGIT is displayed. Press m.
4. Enter the number you want to be detected and press
m.
Unchanged
Empty
Empty
0000
Off
5. Scroll to PREFIX NUM. and press m.
6. Enter the number you want it replaced with and press
m.
Redial list
7. Press > to return to standby.
Master PIN
Keypad lock
Clock
8.13 Country
If you move to another country you can set your phone to be
compatible with the network settings of that country.
00:00
Off
Alarm
NOTE
Dial mode
Tone
If you make a mistake during welcome mode country
selection, you can also reset your country.
Depending on your country, this option may be displayed as
NOT AVAIL or you country may not be displayed.
32
Advanced settings
1. Press m, scroll d to ADVANCED SET and press m.
2. Scroll d to SEL. COUNTRY. Press m.
3. Enter the 4-digit master PIN and press m.
4. Scroll u or d to display the required country.
5. Press m to confirm.
1. Press m, scroll d to ADVANCED SET and press m.
2. Scroll d to ECO MODE and press m.
3. Press u or d to highlight ON or OFF then press m to
confirm.
-
A confirmation beep is emitted and the handset
display will switch between the handset’s name and
ECO MODE
.
8.14 Intrusion
When an external call is taking place, another handset
NOTE
When Eco Mode is set to ON, the handset range will be
reduced.
registered to the base can join in, making the call a 3-way
conference, just by pressing <.
To enable this, Intrusion must be switched On.
1. Press m, scroll d to ADVANCED SET and press m.
2. Scroll d to INTRUSION. Press m.
3. Scroll u or d to ON or OFF
.
4. Press m to confirm.
5. Press > to return to standby.
8.15 ECO mode
To reduce the level of power emissions, you can select low
power or ECO mode. When the ECO mode is set to ON, the
base transmission power will be reduced.
To turn ECO Mode to ON or OFF
:
Advanced settings
33
The
icon is blinking
9. Help
•
Handset is not registered to the base – register the
handset to the base
Charging
•
•
You are too far from the base – move closer to the base
Switch OFF the Eco mode.
The
icon is not scrolling when the handset is placed
on the base
No ring tone
•
•
Bad battery contact – move the handset slightly
Dirty contact – Clean the battery contact with a cloth
moistened with alcohol
•
•
The ring tone is deactivated.
Increase the volume.
•
Battery is full – no need to charge
Caller Line Identification (CLI) service
does not work
Calls
Check your subscription with your network operator
No dialling tone
•
No power – check the connections. Reset the phone:
unplug and plug back in the mains
Batteries are empty – charge the batteries for at least 24
hours
You are too far from the base – move closer to the base
Wrong line cable – use the line cable provided
Line adaptor (when needed) is not connected to the line cord
– connect the line adaptor (when needed) to the line cord
Phonebook
•
A phonebook entry cannot be stored
The phonebook is full. Delete an entry to free memory
•
•
•
Display
No display
•
•
•
Try recharging or replacing the batteries.
Try disconnecting and connecting the base power supply.
If LED is not lit up, then try disconnecting and connecting
the base power supply.
Poor audio quality
The base is too close to electrical appliances, reinforced
concrete walls or metal doorframes – move the base at least
one metre away from any electrical appliances
34
Help
Registration
10.General information
IMPORTANT
This equipment is not designed for making emergency
telephone calls when the power fails. Alternative arrangements
should be made for access to emergency services.
Unable to register another handset
•
•
Maximum number of 5 handsets has been reached.
The display shows SEARCHING. You must unregister a
handset in order to register a new one.
Handset display shows NOT REG
•
Please refer to page 30 of the user guide to re-register
your handset to the base.
This product is intended for connection to analogue public
switched telephone networks and private switchboards in
Singapore.
Interference
Important safety instructions
Follow these safety precautions when using your phone to
reduce the risk of fire, electric shock, and injury to persons
or property:
Noise interference on your radio or television
Your base or charger may be too close. Move it as far away
as possible.
1. Keep all slits and openings of the phone unblocked. Do not
set the phone on a heating register or over a radiator. Ensure
that proper ventilation is provided at the installation site.
2. Do not use while wet or while standing in water.
3. Do not use this product near water (for example, near a
bath tub, kitchen sink, or swimming pool).
4. Do not allow anything to rest on the power cord. Place
the power cord so that it will not be walked on.
5. Never insert objects of any kind into the product vents
as that may result in fire or electric shock.
General information
35
6. Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
Installation Guidelines
1. Read and understand all instructions and save them for
future reference.
7. Do not disassemble this product. If service or repair
work is required, contact the customer service helpline
found in this user's Guide.
2. Follow all warnings and instructions marked on the product.
3. Do not install this product near a bath tub, sink, or shower.
4. Operate this phone using only the power source that is
indicated on the marking label. If you are unsure of the
power supply to your home, consult with your dealer or
local power company.
5. Do not place this product on an unstable cart, stand, or
table. This product may fall, causing serious damage to
the product.
6. Adjust only those controls that are covered by the
operating instructions. Improper adjustment of other
controls may result in damage and will often require
extensive work to restore the product to normal operation.
8. Do not overload wall outlets and extension cords.
9. Avoid using during an electrical storm. Use a surge
protector to protect the equipment.
10. Do not use this phone to report a gas leak, especially if
you are in the vicinity of the gas line.
CAUTION
To reduce the risk of fire, use only the supplied power adaptor.
Unplug this cordless phone immediately from an
outlet if:
•
•
•
The power cord or plug is damaged or frayed.
Liquid has been spilled on the product.
7. Clean this product with a soft, damp cloth. Do not use
chemicals or cleaning agents to clean this phone.
8. Use only the power supply that came with this unit.
The product has been exposed to rain or water. Do not
retrieve the handset or base until after you have
unplugged the power and phone from the wall. Then
retrieve the unit by the unplugged cords.
The product has been dropped or the cabinet has been
damaged.
Using other power supplies may damage the unit.
9. Because this phone operates on electricity, you should have
at least one phone in your home that could operate without
electricity in the case the power in your home goes out.
•
•
The product exhibits a distinct change in performance.
36
General information
10. To avoid interference to nearby appliances, do not place
the base of the phone on or near a TV, microwave oven,
or VCR.
•
Never use household polish as this will damage the
product. Never use a dry cloth as this may cause a static
shock.
Battery Safety Instructions
Environmental
•
Do not burn, disassemble, mutilate, or puncture the
battery. The battery contains toxic materials that could be
released, resulting in injury.
•
•
Do not expose to direct sunlight.
The handset may become warm when the batteries are
being charged or during prolonged periods of use. This is
normal. However, we recommend that to avoid damage
you do not place the product on antique/veneered wood.
Do not stand your product on carpets or other surfaces
which generate fibres, or place it in locations preventing
the free flow of air over its surfaces.
Do not submerge any part of your product in water and
do not use it in damp or humid conditions, such as
bathrooms.
CAUTION
•
There is a risk of explosion if you replace the battery with
•
•
an incorrect battery type. Use only the battery pack that
came with your phone or an authorized replacement
recommended by the manufacturer.
•
•
•
Keep battery packs out of the reach of children.
Remove battery packs if storing over 30 days.
Do not dispose of battery packs in fire, which could result
in explosion.
•
•
Do not expose your product to fire, explosive or other
hazardous conditions.
There is a slight chance your phone could be damaged
by an electrical storm. We recommend that you unplug
the power and telephone line cord during an electrical
storm.
•
The rechargeable battery packs that power this product
must be disposed of properly and may need to be
recycled. Refer to your battery’s label for battery type.
Contact your local recycling center for proper disposal
methods.
SAVE THESE INSTRUCTIONS
Product disposal instructions
•
European Union (EU) Waste of Electrical and
Electronic Equipment (WEEE) directive
Cleaning
•
Clean the handset and base (or charger) with a damp
(not wet) cloth, or an anti-static wipe.
The European Union's WEEE directive requires that
products sold into EU countries must have the crossed
General information
37
out trashbin label on the product (or the package in some
cases). As defined by the WEEE directive, this crossed-
out trashbin label means that customers and end-users
in EU countries should not dispose of electronic and
electrical equipment or accessories in household waste.
Customers or end-users in EU countries should contact
their local equipment supplier representative or service
centre for information about the waste collection system
in their country.
The Waste of Electrical and Electronic Equipment
(WEEE) Directive (2002/96/EC) has been put in place to
recycle products using best available recovery and
recycling techniques to minimize the impact on the
environment, treat any hazardous substances and avoid
the increasing landfill.
Consumer Products and Accessories
Warranty
Thank you for purchasing this Motorola branded product
manufactured under license by Suncorp Technologies
Limited, 3001-3005 China Resources Building, 26 Harbour
Road, Wan Chai, Hong Kong. ("Suncorp")
What Does this Warranty Cover?
Subject to the exclusions contained below, SUNCORP
TECHNOLOGIES LTD. warrants that this Motorola branded
product ("Product") or certified accessory ("Accessory") sold
for use with this product that it manufactured to be free from
defects in materials and workmanship under normal
consumer usage for the period outlined below. This Limited
Warranty is your exclusive warranty and is not transferable.
•
Product disposal instructions for residential users
When you have no further use for it, please remove any
batteries and dispose of them and the product per your local
authority’s recycling processes. For more information please
contact your local authority or the retailer where the product
was purchased.
Who is covered?
This warranty extends only to the first consumer purchaser,
and is not transferable.
What will SUNCORP TECHNOLOGIES LTD do?
SUNCORP TECHNOLOGIES LTD or its authorized distributor
at its option and within a commercially reasonable time, will at
no charge repair or replace any Products or Accessories that
does not conform to this limited warranty. We may use
functionally equivalent reconditioned/ refurbished/ pre-owned
or new Products, Accessories or parts.
Product disposal instructions for business users
Business users should contact their suppliers and check the
terms and conditions of the purchase contract and ensure
that this product is not mixed with other commercial waste
for disposal.
38
General information
Some jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the
length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that
vary from one jurisdiction to another.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR OR
REPLACEMENT PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO
EVENT SHALL MOTOROLA OR SUNCORP
Products Covered
Length of Coverage
Consumer Products
One (1) year from the date of the
products original purchase by the
first consumer purchaser of the
product.
TECHNOLOGIES LTD BE LIABLE, WHETHER IN
CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR
DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES
OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS
OF BUSINESS, LOSS OF INFORMATION OR OTHER
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS
OR ACCESSORIES TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
Consumer Accessories Ninety (90) days from the date
(battery, power supply(s) of the accessories original
and line cords)
purchase by the first consumer
purchaser of the product.
Consumer Products and The balance of the original
Accessories that are
Repaired or Replaced
warranty or for ninety (90)
days from the date returned to
the consumer, whichever is
longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are
excluded from coverage.
General information
39
Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak are
covered by this limited warranty.
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or parts,
are excluded from coverage.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or
neglect, such as physical damage (cracks, scratches, etc.)
to the surface of the product resulting from misuse; (b)
contact with liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or food; (c)
use of the Products or Accessories for commercial purposes
or subjecting the Product or Accessory to abnormal usage or
conditions; or (d) other acts which are not the fault of
Motorola or SUNCORP TECHNOLOGIES LTD., are
excluded from coverage.
Communication Services. Defects, damages, or the failure
of Products or Accessories due to any communication
service or signal you may subscribe to or use with the
Products or Accessories is excluded from coverage.
How to Obtain Warranty Service or Other
Information?
To obtain service or information, please call: (65) 6841 2668
Email: [email protected]
You will receive instructions on how to ship the Products or
Accessories at your expense, to SUNCORP TECHNOLOGIES
LTD. It is the responsibility of the purchaser to contact the
nearest authorised service center/distributor and bring the
product at the purchaser's risk to that authorised service center.
Use of Non-Motorola branded Products and
Accessories. Defects or damage that result from the use of
Non-Motorola branded or certified Products or Accessories
or other peripheral equipment are excluded from coverage.
Authorized Repair Center
Unauthorized Service or Modification. Defects or
damages resulting from service, testing, adjustment,
installation, maintenance, alteration, or modification in any
way by someone other than Motorola, SUNCORP
TECHNOLOGIES LTD. or its authorized service centers, are
excluded from coverage.
To obtain service, you must include: (a) the Product or
Accessory; (b) the original proof of purchase (receipt) which
includes the date, place and seller of the Product; (c) if a
warranty card was included in your box, a completed warranty
card showing the serial number of the Product; (d) a written
description of the problem; and, most importantly; (e) your
address and telephone number.
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
40
General information
Technical Information
Inserting a pause
With some switchboards, after dialling the access code you
may have to wait for a moment while the switchboard picks
up an outside line so you will need to enter a pause in the
dialing sequence.
How many telephones can I have?
All items of telephone equipment have a Ringer Equivalence
Number (REN), which is used to calculate the number of items
which may be connected to any one telephone line. Your
D1000 has a REN of 1. A total REN of 4 is allowed. If the total
REN of 4 is exceeded, the telephones may not ring. With
different telephone types there is no guarantee of ringing, even
when the REN is less than 4.
Press and hold #to insert a pause (P) before entering the
telephone number.
You may also need to enter a pause when storing
international numbers or charge card numbers.
Any additional handsets and chargers that you register have
a REN of 0.
Recall
You may need to use the recall function if you are connected
to a switchboard/PABX (Private Automatic Branch
Exchange), contact your PABX supplier for further
information.
R&TTE
This product is intended for use within Singapore for
connection to the public telephone network and compatible
switchboards.
This equipment complies with the essential requirements for
the Radio Equipment and Telecommunications Terminal
Equipment Directive 1999/5/EC including compliance with
ICNIRP standard for electromagnetic energy exposure.
Connecting to a switchboard
This product is intended for use within Singapore for
connection to the public telephone network.
General information
41
•
To wall-mount the charger, drill two holes in the wall
3.2cm apart horizontally using an 8mm drill bit.
12. Wall mounting
IMPORTANT
Before you wall-mount your D1000, check that you are not
drilling into any hidden wiring or pipes.
Before you drill, make sure the power and telephone line
cables will reach the sockets.
1. Use the following templates to mark the drilling locations.
•
To wall-mount the base, drill two holes in the wall 4.5cm
apart horizontally using an 8mm drill bit.
42
Wall mounting
2. Insert the wall plugs if necessary, then insert the screws
leaving about 5mm protruding from the wall on which to
hang the phone.
3. Pull the base/charger out of the stand and slot the holes
on the back of the base over the screw heads and
gently pull the base/charger down to make sure it is
securely in place.
Wall mounting
43
Manufactured, distributed or sold by Suncorp
Technologies Ltd. , official licensee for this product.
MOTOROLA and the Stylized M Logo are
trademarks or registered trademarks of Motorola
Trademark Holdings, LLC. and are used under
license. All other trademarks are the property of
their respective owners.
© 2012 Motorola Mobility, Inc. All rights reserved.
Version 5 (SG)
|