52
OPERATION GUIDE
Basic Operation
5. BRIGHT +/- (Backlight adjustment)
Pressing or displays the BRIGHT menu when the
menu screen is not displayed.
1
B R I G H T
15
2
5
3
4
Press
or
to adjust the brightness.
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
6. SIZE (Screen size selection)
The menu is displayed.
Press
or
to select the screen size. (See page 4.)
6
7
8
7. DISPLAY
Displays monitor information. Every time you press this button,
the display changes from INFORMATION 1
→
INFORMATION 2
display clear and so on.
→
INFORMATION 1
XXXX/XX/XX XXX
XX:XX:XX
INPUT MODE
SIZE
:
:
:
:
:
:
:
:
:
PC3 D-SUB
WIDE
STD
15
COLOR MODE
BRIGHT
1. INPUT (Input mode selection)
The menu is displayed. Press
or
to select the input
VOLUME
ID No.
15
mode, and press
to enter.
0
* You can select the input terminal by pressing the input
switch of the monitor.
MODEL
LDT521V
S/N
STATUS
XXXX-XXXX-XXXX-XXXX
Input mode
PC1 DVI-D*1
PC2 HDMI*2
Video
Audio
LAN
PC1 input terminal
PC2 input terminal
PC3 input terminal
PC4 input terminals
AV1 input terminal
AV2 input terminal
AV3 input terminals
AV4 input terminal
AV5 input terminal
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 66.3 kHz
PC audio input
terminal
PC3 D-SUB
PC4 RGB*3
INFORMATION 2
XXXX/XX/XX XXX
XX:XX:XX
RS-232C/LAN SELECT
:
:
:
:
LAN
OFF
AV1 DVI-D*1
AV2 HDMI*2
AV3 COMPONENT*3
AV4 S-VIDEO
AV5 VIDEO
DHCP CLIENT
IP ADDRESS
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXXXXXXXXXXX
XXXXX
AV audio input
terminals
SUBNET MASK
DEFAULT GATEWAY :
MONITOR NAME
DATA PORT
:
:
:
MAC ADDRESS
XX-XX-XX-XX-XX-XX
*1 Select the terminal for DVI SELECT. (See page 7.)
*2 Select the terminal for HDMI SELECT. (See page 7.)
Select the terminal for HDMI AUDIO SELECT which is
used for audio input. (See page 7.)
LAN
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 66.3 kHz
*3 Select the terminal for BNC SELECT. (See page 7.)
• The display disappears automatically after about 15
seconds.
2. MUTE
•
LAN is displayed during LAN communication.
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
• If LAN is displayed in red, there is a duplicate IP address.
8. MODE (Color mode selection)
Each time you press this button, the color mode changes in
the following order:
3. MENU
Displays and turns off the menu screen (see page 5).
STD (Standard)
VIVID
sRGB
STD...
→
→
→
4. VOL +/- (Volume adjustment)
Pressing
menu screen is not displayed.
or
displays the VOLUME menu when the
• sRGB applies to PC input only.
sRGB is international standard of color representation
specified by IEC (International Electrotechnical
Commission). Color conversion is made in taking account
of liquid crystal’s characteristics and represents color tone
close to its original image.
V O L U M E
15
Press
or
to adjust the volume of the sound.
* If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
E
3
Basic Operation
Switching the screen size
„
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDE
PC input
AV input
PC input
AV input
PC input
AV input
PC input
AV input
PC input
AV input
Displays image so it fills the entire screen.
An image with a 4:3 aspect ratio is stretched to fill the entire
screen.
ZOOM 1
ZOOM 2
NORMAL
Dot by Dot
An image with a 4:3 aspect ratio is enlarged to fill the entire screen
without changing the aspect ratio. The edges of the image may be
cut off.
Use this size if ZOOM 1 cuts off the subtitles.
Displays image so it fills the screen without changing the aspect
ratio of the input signals.
Displays the entire image of the aspect ratio of 4:3 without
changing the aspect ratio.
Displays the dots of the signals input from the connected PC as
the corresponding dots on the screen. *
Displays the dots of the input signals as the corresponding dots on
the screen.
*: With a monitor of screen resolution 1600 x 1200 or 1920 x 1200, selecting Dot by Dot displays the NORMAL screen.
TIPS
• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial
or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright
Law, so please be careful.
• When “Enlarge” is set, the screen size is fixed to “WIDE” mode.
• When dual-screen display is selected, the screen size cannot be changed.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original
image (e.g. TV broadcast or video input from external equipment).
• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this
monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen
size to “NORMAL”.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen
size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
E
4
Menu Items
Menu screen display
„
Displaying the menu screen
1
3
2
4
Video and audio adjustment and settings of various functions
are enabled. This section describes how to use the menu
items. See pages 6 to 8 for details of each menu items.
SCREEN
PICTURE
AUDIO
PICTURE
1/2
PC3 D-SUB
AUTO
CONTRAST
BLACK LEVEL
TINT
30
96
30
30
12
Example of operation
„
SETUP
(Adjusting CONTRAST in the PICTURE menu)
OPTION
ENLARGE
PIP/PbyP
1. Press MENU to display the menu screen.
COLORS
SHARPNESS
SCREEN
PICTURE
AUDIO
SCREEN
AUTO
1/1
PC3 D-SUB
OK···[MENU]
600
31
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 66.3 kHz
CLOCK
PHASE
150
31
50
50
1920
1080
H-POS
V-POS
H-SIZE
V-SIZE
H-RESOLUTION
V-RESOLUTION
RESET
SETUP
1 Name of the menu
2 Input mode
3 An item being selected (highlighted)
OPTION
ENLARGE
PIP/PbyP
4 Screen resolution of input signal, and other data.
END···[MENU]
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 66.3 kHz
TIPS
• Items that cannot be selected appear in gray.
(e.g. Function not supported by the current input signal)
2. Press
or
to select PICTURE, and press
.
PICTURE menu is displayed.
3. Press
or
to select CONTRAST.
SCREEN
PICTURE
AUDIO
PICTURE
1/2
PC3 D-SUB
AUTO
CONTRAST
BLACK LEVEL
TINT
30
96
30
30
12
SETUP
OPTION
ENLARGE
PIP/PbyP
COLORS
SHARPNESS
OK···[MENU]
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 66.3 kHz
4. Press
or
to adjust the setting.
SCREEN
PICTURE
AUDIO
PICTURE
1/2
PC3 D-SUB
AUTO
CONTRAST
40
96
30
30
12
SETUP
BLACK LEVEL
TINT
OPTION
ENLARGE
PIP/PbyP
COLORS
SHARPNESS
OK···[MENU]
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 66.3 kHz
For items that have
press MENU
, press
, make settings and then
.
5. Press MENU twice to close the menu screen.
TIPS
• The menu will differ depending on the input mode.
• The menu screen will close automatically if no operation is
performed for about 15 seconds. (DATE/TIME SETTING,
SCHEDULE and LAN SETUP screens will close in about 4
minutes.)
E
5
Menu Items
SHARPNESS
Menu item details
The menu will differ depending on the input mode.
Adjusts the sharpness of the image.
ADVANCED (AV input)
You can adjust more specifically. (See page 10.)
COLOR MODE
SCREEN
AUTO (PC3/PC4)
„
Changes the color mode on the screen. The color mode on
the screen can also be changed using a remote control unit.
(See page 3.)
The CLOCK, PHASE, H-POS, and V-POS are automatically
adjusted.
Pressing
performs adjustment.
* sRGB is PC input only. See page 3 for details.
Use this automatic adjustment when you use the PC3 input
terminal or PC4 input terminals to display a PC screen for
the first time or when you change the setting of the PC. (See
page 10.)
WHITE BALANCE
THRU.............. Displays the input signal level as is. (for PC1/
PC2 only)
PRESET ......... Selects the color temperature using PRESET.
USER.............. Used for adjusting R-CONTRAST,
G-CONTRAST, and B-CONTRAST
respectively.
CLOCK (PC3/PC4)
Adjusts frequency for sampling clock for applicable video.
Adjust when there is flickering in the form of vertical stripes.
When using the adjustment pattern (see page 10), make
adjustments so that no vertical stripe noise appears in it.
PRESET
PHASE (PC3/PC4)
Selects the color temperature when the WHITE BALANCE is
set to PRESET.
The setting values are shown for reference. The color
temperature of the screen varies over time.
This function is not intended to keep the color temperature
constant.
Adjusts sampling clock phase for applicable video.
Useful when small characters appear with low contrast and/
or there are flickers at corners.
When using the adjustment pattern (see page 10), make
adjustments so that no horizontal stripe noise appears in it.
* Adjustments to PHASE should be made only after CLOCK
has been correctly set.
R-CONTRAST
Adjusts red component when the WHITE BALANCE is set to
USER.
H-POS
Adjust the horizontal position of the image.
V-POS
G-CONTRAST
Adjusts green component when the WHITE BALANCE is set
to USER.
Adjust the vertical position of the image.
H-SIZE
B-CONTRAST
Adjusts blue component when the WHITE BALANCE is set
to USER.
Adjust the horizontal size of the image.
V-SIZE
COPY TO USER
Adjust the vertical size of the image.
H-RESOLUTION (PC3/PC4)
Copies the value set for PRESET to the USER setting.
Select “ON” and then press MENU
GAMMA
.
Sets proper horizontal resolution when the resolution of
input signals is not recognized properly. (Adjustment may be
impossible with some signals.)
Select a gamma value.
RESET
V-RESOLUTION (PC3/PC4)
Resets the values of the PICTURE menu items to the factory
preset values.
Sets proper vertical resolution when the resolution of input
signals is not recognized properly. (Adjustment may be
impossible with some signals.)
Select “ON” and then press MENU
.
RESET
AUDIO
TREBLE
„
Resets the values of the SCREEN menu items to the factory
preset values.
Select “ON” and then press MENU
.
Adjusts the volume of treble-level sound.
BASS
PICTURE
„
Adjusts the volume of bass-level sound.
BALANCE
AUTO (PC3/PC4)
The CONTRAST and BLACK LEVEL are automatically
adjusted.
Adjusts the balance of the audio sound between right and left.
RESET
Pressing
performs adjustment.
Resets the values of the AUDIO menu items to the factory preset values.
CONTRAST
Select “ON” and then press MENU
.
Adjusts the brightness of the image.
BLACK LEVEL
SETUP
„
Adjusts the entire brightness of the video signals.
TINT
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the hue. Selecting + changes the color towards
green, and selecting - changes it towards magenta.
Adjusts the vertical display position of menu screen.
COLORS
Adjusts the color intensity.
E
6
Menu Items
SCREEN MOTION
ID No. SET
Residual images are reduced by moving the screen.
PATTERN 1 .... The whole screen moves vertically and
horizontally.
PATTERN 2 .... A black screen spreads from the bottom of
the screen and then shrinks to the bottom of
the screen. If the monitor is installed in the
vertical orientation, a black screen spreads
from the left end of the screen and then
shrinks to the left end of the screen.
Assigns ID numbers to monitors connected in a daisy chain
(see page 13), using RS-232 cables.
The numbers 1 to 255 are available for ID numbers.
If “0” is set, the system regards this as the state where no ID
number is set.
LAN SETUP
Configures the settings to control the monitor from the
computer via LAN. (See page 21.)
PATTERN 3 .... A black bar moves from the left end to the right
end of the screen. If the monitor is installed in
the vertical orientation, a black bar moves from
the top to the bottom of the screen.
PATTERN 4 .... Black screens appear from both the top and
bottom of the screen, and the displayed
image is compressed into the central field.
If the monitor is installed in the vertical
OPTION
DATE/TIME SETTING
„
Set the date and time. Press
time, and press
Set the date in “Year/Month/Day” order.
Set the time on a 24-hour basis.
or
to select the date and
or
to change the numerical values.
orientation, the screen is compressed from
the left and right ends.
SCHEDULE (See page 9.)
You can set the time to switch the monitor on and off.
INPUT SELECT
PATTERN1
PATTERN2
PATTERN3
PATTERN4
DVI SELECT.......Selects the input mode to be used.
BNC SELECT.....Selects the input mode to be used.
HDMI SELECT ...Selects the input mode to be used.
HDMI AUDIO SELECT ..Selects a terminal to which audio signals
are input in PC2/AV2 mode.
MOTION TIME 1
Specify a time period (operating interval) until SCREEN
MOTION starts.
AUDIO OUTPUT
MOTION TIME 2
Sets the volume of sound output from the PC/AV audio
output terminals.
VARIABLE ..........You can adjust the volume using VOLUME.
FIXED.................Fixes the sounds.
Specify a time period during which SCREEN MOTION
operates (time period during which the screen will move).
MONITOR
Select the installation direction of the monitor.
LANDSCAPE............Horizontal orientation
PORTRAIT ...............Vertical orientation
INPUT SIGNAL (PC3/PC4)
If a computer connected to the PC3/PC4 input terminal
outputs any of the following resolutions, make a selection
from the following options.
LANGUAGE
Sets the display language for the menu screen.
HDMI AUTO VIEW
480 LINES..........AUTO, 640x480 or 848x480
768 LINES..........AUTO, 1024x768, 1280x768, or 1360x768
1050 LINES........1400x1050 or 1680x1050
When ON is selected, the screen size is adjusted
automatically according to the screen size control signal
included in the video signal input from the AV2 input terminal.
SCAN MODE (AV input)
Sets the scan mode used for AV mode input.
MODE1...............Over-scan display
MODE2...............Under-scan display
MODE3...............Under-scan display when the input signal
is 1080i/p. Otherwise, over-scan display
POWER ON DELAY
You can delay the screen display after the monitor is turned
on. The period can be set up to 60 seconds in units of one
second. When this function is activated, the power LED
flashes (at approx. 1 second interval) in orange. This function
is disabled when 0 is specified.
*
Even when MODE1 is selected, under-scan display is used when
the input signal is 1080i/p and the screen size is Dot by Dot.
SELF ADJUST
STANDBY MODE
On a PC3/PC4 screen, specify whether to perform screen
adjustment automatically or not. When ON is selected, the
screen is automatically adjusted when its resolution is 800
x 600 or higher and the timing of input signals changes.
“ADJUSTING” appears on the screen during the adjustment.
When STANDARD is selected, startup time from standby
mode is reduced. Note, however that, more power will be
consumed in standby mode.
When LOW POWER is selected, current consumption
is reduced while the monitor is in standby mode. Note,
however, that the startup time from standby mode becomes
longer. Also, certain RS-232C commands cannot be used in
standby mode. (See page 16.)
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to
switch modes from no signal to the input signal standby
mode when the PC screen is displayed.
RS-232C/LAN SELECT
AUTO INPUT CHANGE
Selects the method with which to control the monitor from
the computer.
Specify whether to change inputs automatically. When ON is
selected and no signal is present in the selected input mode,
AUTO INPUT CHANGE automatically changes the selected
mode to another mode where a video signal is present.
When video signals exist in multiple input modes, the
switching priority is as follows:
PC1, PC2, PC3, PC4, AV1, AV2, AV3, AV4 and AV5.
(Input mode switching may take 15 seconds or more,
depending on the connected equipment. Input signals
may not be detected properly and a priority may change,
depending on the connected equipment or video signals.)
RS-232C/LAN COMMAND
Set the return value for the RS-232C command.
Normally, you do not need to change this setting from NORMAL.
NORMAL ...... The end code of the return value is CR+LF.
MODE1......... The end code of the return value is CR only.
MODE2......... The length of the return value is fixed to 4
digits. The end code is CR only.
When the return value has 1 to 3 digits, the
empty digit(s) from the left is filled with a
one-byte space(s).
E
7
Menu Items
COLOR SYSTEM (AV4/AV5)
TIPS
Select the color system of the AV equipment which is
connected to AV4 and AV5 input terminal. (AUTO / PAL /
PAL-60 / SECAM / NTSC3.58 / NTSC4.43)
When AUTO is selected, the color system is automatically
set according to the input signal.
• When WHITE BALANCE is set to THRU, BLACK LEVEL,
CONTRAST, TINT, COLORS and GAMMA cannot be set.
• If COLOR MODE is set to sRGB or VIVID, the following
items cannot be set.
WHITE BALANCE, PRESET, R-/G-/B-CONTRAST, COPY
TO USER, and GAMMA
ENLARGE (PC input)
ENLARGE H
„
Dual screen display
„
You can display the screens of the PC input signal and AV
input signal simultaneously.
Set this function with “PIP MODES” in the PIP/PbyP menu.
Sets the number of screen splits (number of monitors) in the
horizontal direction used for the enlargement. (See page 9.)
ENLARGE V
PIP
A sub screen is displayed
inside a main screen.
Sets the number of screen splits (number of monitors) in the
vertical direction used for the enlargement. (See page 9.)
Main screen
ENLARGE-POS H / ENLARGE-POS V
Sub
screen
Specify the split screen to be displayed when the
enlargement function is used. (See page 9.)
PbyP
PbyP2
A main screen and a sub
screen are displayed in a
line.
BEZEL H / BEZEL V
Main
screen
Sub
screen
Sets the frame width of the display when the enlargement
function is used.
H-POS
Adjust the horizontal position of the enlarged screen.
V-POS
Displays a main screen
which measures 1280
pixels in the longest
direction and a sub
screen in a line.
Sub
screen
Main screen
Adjust the vertical position of the enlarged screen.
PIP/PbyP
„
PIP MODES
* The currently selected input signal is displayed on the main
screen.
* You cannot simultaneously display the screens of signals
of the same type, such as two types of PC input signals or
two types of AV input signals.
* The dual screen display cannot be used with the
combination of PC1 and AV2 or of AV1 and PC2.
Sets the display method.
OFF .........Displays one screen.
PIP...........Displays a sub screen inside a main screen.
PbyP........Displays a main screen and a sub screen in a line.
PbyP2......Displays a main screen which measures 1280 pixels
in the longest direction and a sub screen in a line.
PIP SIZE
TIPS
Sets the size of the sub screen in PIP mode.
• You might infringe on a copyright of the author which is
protected by copyright law when you display the images of
the computer screen and television/VCR simultaneously for
profit-making or to show the image to the public.
• The screen size for dual-screen display is the same as
the screen size for single-screen display. The Dot by Dot
screen is displayed in NORMAL size except when it is set
as the PIP main screen.
PIP H-POS
Adjusts the horizontal position of the sub screen in PIP mode.
PIP V-POS
Adjusts the vertical position of the sub screen in PIP mode.
PIP BLEND
In PIP mode, use this menu item to display the sub screen
transparently.
• When dual-screen display is selected, the AUTO INPUT
CHANGE function is disabled.
• When dual-screen display is selected, the SCREEN
PIP SOURCE
Selects the input signal of the sub screen in PIP, PbyP, or
PbyP2 mode.
MOTION function is disabled.
• When dual-screen display is selected, the screen cannot
be enlarged.
• When dual-screen display is selected, the following
adjustments of ADVANCED are invalid and adjusting is
disabled.
3D-NR, MPEG-NR and 3D-Y/C
• When dual-screen display is selected, the INPUT SELECT
options cannot be set.
SOUND CHANGE
Sets the sound which is output in PIP, PbyP, or PbyP2 mode.
If the main screen is displayed as a full screen by the AUTO
OFF function, the sound for the main screen is output even
when the sound for the sub screen is specified.
MAIN POS
Sets the position of the main screen in PbyP or PbyP2 mode.
PbyP2 POS
Sets the position of the sub screen in PbyP2 mode.
AUTO OFF
Sets the display method when no signals for the sub screen
are input in PIP, PbyP, or PbyP2 mode.
MANUAL....... Displays a main screen and a black sub screen.
AUTO............ Displays the main screen as a full screen.
E
8
Menu Items
Enlarge
„
TIPS
• You can align several monitors and integrate them into a
single large screen to display.
• Up to five monitors can be aligned in both the horizontal
and vertical directions.
• Each monitor displays enlarged views of separated images.
• AV input signals cannot be used for the Enlarge function.
• To connect 6 or more monitors using PC1 signals, a splitter
for the video signal (commercially available) is required.
• When connected in PC2/PC3/PC4, a splitter for the video
signal (commercially available) is required.
• When Enlarge is used, the AUTO INPUT CHANGE function
is disabled.
(Example)
Horizontal direction: 2 monitors
Vertical direction: 2 monitors
• When Enlarge is used, the SCREEN MOTION function is
disabled.
• To cancel the enlargement, set 1 for ENLARGE H and
ENLARGE V respectively.
SCHEDULE
You can set the time to switch the monitor on and off.
Set this function with “SCHEDULE” in the OPTION menu. (See
page 7.)
„
Horizontal direction: 3 monitors
Vertical direction: 2 monitors
PC3 D-SUB
SCHEDULE
XXXX/XX/XX XXX XX:XX:XX
No.
(1) POWER (2)
DAY OF THE WEEK (3)
TIME(4)
INPUT(5)
Setting procedure
In the ENLARGE menu, set ENLARGE H/V and
ENLARGE-POS H/V. (See page 8.)
1. Set the number of monitors aligned in the horizontal
direction in ENLARGE H.
2. Set the number of monitors aligned in the vertical
direction in ENLARGE V.
3. Set the section of the separated image to be displayed
on each monitor in ENLARGE-POS H and
ENLARGE-POS V.
…
OK [MENU]
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 66.3 kHz
In horizontal orientation
ENLARGE H
1. Press
press
2. Set the SCHEDULE. (See the description below.)
Press or to select items, and press or
change the setting.
3. Press MENU
SCHEDULE becomes effective.
or
to select the SCHEDULE number, and
1
2
3
4
5
.
1
2
3
4
5
(1,1)
(2,1)
(3,1)
(4,1)
(5,1)
to
(1,2)
(1,3)
(1,4)
(1,5)
(2,2)
(2,3)
(2,4)
(2,5)
(3,2)
(3,3)
(3,4)
(3,5)
(4,2)
(4,3)
(4,4)
(4,5)
(5,2)
(5,3)
(5,4)
(5,5)
.
(1)
• : SCHEDULE effective
: SCHEDULE not effective
(2) POWER
ON : Switches the monitor on at the specified time.
-
In vertical orientation
OFF : Switches the monitor off at the specified time and puts
ENLARGE H
the monitor in standby mode.
5
4
3
2
1
(3) DAY OF THE WEEK
(5,1) (4,1) (3,1) (2,1) (1,1)
(5,2) (4,2) (3,2) (2,2) (1,2)
(5,3) (4,3) (3,3) (2,3) (1,3)
(5,4) (4,4) (3,4) (2,4) (1,4)
(5,5) (4,5) (3,5) (2,5) (1,5)
1
2
3
4
5
Specifies the day of the week to execute the SCHEDULE.
ONLY ONCE:
Executes the SCHEDULE once on the specified day.
Specify the day of the week to execute the SCHEDULE.
EVERY WEEK:
Executes the SCHEDULE on the specified day of the week
every week. Specify the day of the week to execute the
SCHEDULE.
Periodic setting such as “Monday through Friday” is also
possible.
EVERY DAY:
Executes the SCHEDULE every day regardless of the day
of the week.
(4) TIME
Specifies the time to execute the SCHEDULE.
Set the time on a 24-hour basis.
* The numbers in parentheses are the setting values in
(ENLARGE-POS H, ENLARGE-POS V) format.
E
9
Menu Items
(5) INPUT
Adjustments for PC screen display
Specifies the input mode at power-on. When not specifying,
the screen at the previous power-off appears.
Input modes displayed on “PC1/AV1” depend on DVI
SELECT settings.
Input modes displayed on “PC2/AV2” depend on HDMI
SELECT settings.
Automatic adjustment
„
When you use the PC3 input terminal or PC4 input terminals
to display a PC screen for the first time, or when you change
the setting of the PC, use the automatic screen adjustment.
1. Switch the input to PC3 or to PC4 and display the
adjustment pattern. (See the description below.)
Input modes displayed on “PC4/AV3” depend on BNC
SELECT settings.
2. Press MENU and use
menu.
or
to display the SCREEN
Caution
3. Press
4. Press
and select “AUTO”.
• Do not switch off the main power after setting the
SCHEDULE.
• Specify the correct date and time. (See page 7.)
SCHEDULE does not function unless the date and time are
specified.
.
The automatic adjustment is complete in several seconds.
5. Press MENU twice to close the menu screen.
• Check regularly that the set date and time are correct.
TIPS
• If the screen cannot be adjusted properly with one
automatic adjustment, repeat the automatic adjustment two
or three times. Try manual adjustment if necessary.
TIPS
• Up to 8 SCHEDULE items can be registered.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
Screen display for adjustment
„
• A SCHEDULE that has a large number has precedence
over that of a small number when schedules overlap.
Before making adjustments in the SCREEN menu or
PICTURE menu, display an image to brighten the entire
screen. If you are using a Windows PC, use the adjustment
pattern on the supplied CD-ROM.
ADVANCED items (AV input) (See page 6.)
„
FLESH TONE
Adjust the hue control.
3D-NR
Opening the adjustment pattern
1. Load the supplied CD-ROM into the computer’s CD-
ROM drive.
2. Open the CD-ROM in [My Computer].
3. Double-click [Adj_uty.exe].
Reduce the noise of playback images on video.
Setting a higher level reduces more noise. However, it may
cause blurring on an image.
The adjustment pattern will appear.
Adjust the screen automatically or manually.
MPEG-NR
Reduce block noise caused by digital compression.
3D-Y/C (AV5)
Specify whether to perform 3-dimension Y/C separation.
If dot interference or cross-color is occurring in fast-motion
scenes, selecting “OFF” may improve the image quality.
C.M.S.-HUE
4. When adjustment is finished, press the [Esc] on the
computer’s keyboard to quit the adjustment program.
5. Eject the CD-ROM from the CD-ROM drive.
Adjusts color tone with 6 colors of R (red), Y (yellow), G
(green), C (cyan), B (blue), and M (magenta).
C.M.S.-SATURATION
Adjusts color vividness with 6 colors of R (red), Y (yellow), G
(green), C (cyan), B (blue), and M (magenta).
TIPS
• If the display mode on the computer you are using is
65,000 colors, the color levels in the color pattern may
appear differently or grayscale may appear to be colored.
(This is due to the specifications of the input signal and is
not a malfunction.)
C.M.S.-VALUE
Adjusts color brightness with 6 colors of R (red), Y (yellow),
G (green), C (cyan), B (blue), and M (magenta).
TIPS
• When FLESH TONE is set to LOW or HIGH, C.M.S.-HUE/
-SATURATION/-VALUE cannot be set.
E
10
Initialization (Reset)/Functional Restriction Setting
You can return the settings to their factory-preset values and
restrict operations.
TEMPERATURE ALERT
Selects the notification method for an abnormal
temperature.
OFF .............. Do not notify about an abnormal
temperature.
SIZE
1. After pressing
for about 5 seconds, press
in that order.
,
,
, and
OSD & LED .. When an abnormal temperature is
detected, the power LED flashes in red
and green alternately and the screen
displays a message: TEMPERATURE.
LED............... When an abnormal temperature is
detected, the power LED flashes in red
and green alternately.
1/1
FUNCTION
ALL RESET
ADJUSTMENT LOCK
RS-232C/LAN
OFF
UNLOCKED
ON
OSD DISPLAY
LED
ON
STATUS ALERT
TEMPERATURE ALERT
STATUS ALERT
LED
Selects the notification method for a hardware error.
OFF .............. Do not notify about the error.
OSD & LED .. When a hardware error is detected, the
power LED flashes in red and the screen
displays a message: STATUS [xxxx].
OFF
…
END [MENU]
2. Select and set the items.
ALL RESET
LED............... When a hardware error is detected, the
power LED flashes in red.
Resets the settings to the factory default settings.
3. Press MENU to return to the normal screen.
Press
, select the resetting method, and then press
MENU
.
TIPS
After initialization, turn the main power switch off and
then back on.
• When both abnormal temperature and hardware error are
ALL RESET1 ....Resets all the settings to the factory
default settings.
detected, the hardware error notification overrides.
ALL RESET2 ....Returns all settings to the factory default
settings except for the following items:
LAN SETUP, RS-232C/LAN SELECT,
NETWORK, MAIL, and SERVICE &
SUPPORT (See page 7, and pages 25
to 28.)
ADJUSTMENT LOCK
You can disable operations on the monitor and the
remote control unit that use buttons.
OFF ...Enables operation.
1.........Disables all operations other than turning power
on/off and FUNCTION.
2.........Only the FUNCTION operation is enabled.
Disables all operations other than FUNCTION (not
even power on/off).
RS-232C/LAN
Specifies whether to allow control via RS-232C or LAN
(see pages 12 and 21).
OSD DISPLAY
Hides/shows menus.
The FUNCTION screen cannot be hidden.
LED
Specifies whether to light power LEDs.
E
11
Controlling the Monitor with a PC (RS-232C)
You can control this monitor from a PC via RS-232C (COM
port) on the PC.
Communication conditions
You can also connect multiple monitors via a daisy chain by
using a PC. By assigning ID numbers to each monitor (see
page 13), you can make input mode selection/adjustment or
can check the status of a specific monitor.
Set the RS-232C communication settings on the PC to match
the monitor’s communication settings as follows:
Baud rate
Data length
Parity bit
9600 bps
8 bits
Stop bit
1 bit
Flow control
None
Caution
None
• To control the monitor via RS-232C, set RS-232C/LAN
SELECT to RS-232C.
• You cannot use RS-232C and LAN control simultaneously.
Communication procedure
Command format
„
PC connection
When a command is sent from the PC to the monitor, the
monitor operates according to the received command and
sends a response message to the PC.
Return code
One-to-one connection with a PC
„
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the monitor.
C1 C2 C3 C4 P1 P2 P3 P4
Parameter field
(4 character string comprised of:
0-9, +, -, space, ?)
Command field
(4 prescribed
alphanumerical characters)
Example: VOLM0030
RS-232C input terminal
VOLM
30
* Be sure to input 4 characters for the parameter. Pad with
spaces (“ ”) if necessary.
PC
H
H
H
(“
” is a return code (0D , 0A or 0D ))
To COM port
Wrong : VOLM30
Right : VOLM
30
RS-232 straight cable
(commercially available)
When inputting a negative value, specify a numerical value in
three digits.
Example: AUTR-009
Advanced operation
Daisy chain connection…
„
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the first monitor.
Next, connect RS-232 straight cable to the first monitor’s
RS-232C output terminal and to the second monitor’s
RS-232C input terminal. Connect in the same way to the third
and subsequent monitors.
Do not use spaces for MPOS, DATE, and SC01 through
SC08. Specify parameters using a specified number of
characters.
Example: MPOS010097
If a command has “R” listed for “DIRECTION” in the
“RS-232C command table” on page 16, the current value can
be returned by using “?” as the parameter.
Up to 25 monitors can be connected. (Depending on the
length of the cable used and the surrounding environment.)
First monitor
Second monitor
Example:
From PC to monitor (How much
is current volume setting?).
VOLM ? ? ? ?
30
←
←
From monitor to PC (Current
volume setting: 30).
RS-232C
* If an ID number (see page 13) has been assigned
(For example, ID number = 1).
input terminal
RS-232C
output terminal
From PC to monitor.
From monitor to PC.
VOLM
30
?
←
←
001
PC
RS-232 straight cables
(commercially available)
To COM port
E
12
Controlling the Monitor with a PC (RS-232C)
Communication interval
Response code format
„
„
When a command has been executed correctly
• After OK or ERR is returned, you must send the following
commands.
O
K
Return code
(0DH, 0AH)
To set a timeout for the command response, specify 10
seconds or longer.
• Provide an interval of 100 ms or more between the
command response and the transmission of the next
command.
A response is returned after a command is executed.
* If an ID number has been assigned
Return code
Space (20H)
(0DH, 0AH)
VOLM0020
OK
O
K
SPC
0
0
1
Interval of 100 ms or more
ID number of responding monitor
INPS0001
WAIT
When a command has not been executed
OK
E
R
R
Return code
(0DH, 0AH)
TIPS
* If an ID number has been assigned
• When executing ALL RESET, set the timeout period to 30
seconds or longer.
• When turning the power on while the POWER ON DELAY
function is in use, set the timeout period to the POWER ON
DELAY period + 10 seconds or longer.
Return code
(0DH, 0AH)
Space (20H)
E
R
R
SPC
0
0
1
ID number
Advanced operation
TIPS
This section explains commands for daisy chain connection.
The basic communication procedure is the same as in the
“One-to-one connection with a PC” section.
• “ERR” is returned when there is no relevant command or
when the command cannot be used in the current state of
the monitor.
• If communication has not been established for reasons
such as a bad connection between the PC and monitor,
nothing is returned (not even ERR).
ID numbers
You can assign a unique ID number to each monitor (see
page 7). This allows you to control a particular monitor in a
daisy chain of monitors.
You can assign ID numbers either from the menu screen (using
the remote control) or from the PC using RS-232 cable.
„
• If no monitor has been assigned the designated ID number
(e.g. if the command IDSL0002
is used, but no monitor
with ID number: 2 is found), no response is returned.
• If RS-232C/LAN COMMAND is set to options other than
NORMAL, the return code for a response is 0DH only.
[Example]
ID number: 1 ID number: 2 ID number: 3 ID number: 4
If execution of the command is taking some time
W
A
I
T
Return code
(0DH, 0AH)
If monitors are connected as shown above, you can
execute commands like “Set the volume of the monitor with
ID 4 to 20”.
When the following commands are used, “WAIT” is returned.
In this case, a value will be returned if you wait a while. Do not
send any command during this period.
No ID number is attached to WAIT response.
• Commands which return WAIT:
When controlling monitors linked in a daisy chain by
designating ID numbers, you should basically avoid any
duplication of ID numbers.
ID numbers do not have to be assigned in ascending order
starting from the PC. They can also be connected as shown
below.
1. When repeater control is used
2. When an IDSL or IDLK command is used
3. When one of the following commands is used: RSET,
INPS, ASNC, WIDE, EMAG, EPOS, PXSL, POWR,
AGIN, MWIN, MWIP, MWPP, ESTG, EMHV, EPHV,
ESHV
[Example]
ID number: 3 ID number: 2 ID number: 4 ID number: 1
When control via RS-232C is locked (to prevent use)
using the operation lock function (see page 11)
L
O
C
K
E
D
Return code
(0DH, 0AH)
When RS-232C/LAN SELECT is set to LAN
U
N
S
E
L
E
C
T
E
D
Return code
(0DH, 0AH)
E
13
Controlling the Monitor with a PC (RS-232C)
IDLK ........The parameter of this command sets the ID
number of the monitor. The monitor is subject to all
subsequent commands.
Commands for ID control
The command examples shown on this page assume the
following connection and ID number set up.
„
ID number: 1 ID number: 2 ID number: 3 ID number: 4
Example:
Following commands are for the monitor
with ID number: 2.
IDLK0002
WAIT
←
Searching for monitor with ID number:
2
←
←
←
←
IDST .........A monitor receiving this command sets its own ID
Found monitor with ID number: 2
OK
002
number in the parameter field.
Sets volume of monitor with ID
number: 2 to 30.*
Example:
IDST0001
VOLM0030
WAIT
Processing
The ID number of this monitor is set to 1.
OK
001
←
OK
002
Sets volume of monitor with ID
number: 2 to 20.*
VOLM0020
WAIT
←
TIPS
You can automatically assign ID numbers by using the IDST
command with the Repeater control (see “Repeater control”
on page 15).
For example, using the command “IDST001+” automatically
sets the ID numbers, as shown below.
OK
002
Canceling fixed ID number setting
Canceling IDLK
IDLK0000
WAIT
←
←
←
Cancelation complete
OK
002
[Example]
ID number: 1 ID number: 2 ID number: 3 ID number: 4
VOLM0010
The volume of the monitor with ID number:
1 (the one directly connected to the PC) is
set to 10. (IDLK is canceled.)
OK
001
←
* The IDLK command remains effective until it is
canceled, or power is shut off.
ID setting command with repeater control
IDST001 +
WAIT
←
IDCK........Provides screen display of the ID number currently
assigned to a monitor, and the ID number currently
set for IDLK (if any).
“OK” response from ID number: 1
“OK” response from ID number: 2
“OK” response from ID number: 3
“OK” response from ID number: 4 (End)
OK
OK
OK
OK
001
002
003
004
←
←
←
←
Example:
(After executing IDLK0002)
IDCK0000
(Parameter has no meaning.)
←
←
←
IDSL ........The parameter of this command sets the ID number
of the monitor. The monitor is subject to the next
command.
Returned response. The ID
number is also displayed on the
monitor screen.
ID : 001 IDLK : 002
Example:
Repeater control. (If a command
is used with repeater control, ID
designation using IDSL or IDLK
is canceled.)
IDCK000 +
The next command is for the monitor
with ID number: 2.
WAIT
IDSL0002
WAIT
←
ID : 001 IDLK : 000
ID : 002 IDLK : 000
ID : 003 IDLK : 000
ID : 004 IDLK : 000
Searching for monitor with ID number:
2
←
←
←
←
←
←
Found monitor with ID number: 2
OK
002
Sets volume of monitor with ID
number: 2 to 30.
VOLM0030
WAIT
Processing
OK response from monitor with ID
number: 2
OK
VOLM0020
OK 001
002
Sets volume to 20.
The volume of the monitor with ID
number: 1 (the one directly connected
to the PC) is set to 20.*
←
* The IDSL command is effective only once, for the
immediately succeeding command.
E
14
Controlling the Monitor with a PC (RS-232C)
Repeater control
„
This system has a function to allow setting of multiple
monitors connected in a daisy chain using a single command.
This function is called repeater control. You can use Repeater
control function without assigning ID numbers.
[Example]
Set 1
Set 2
Set 3
Set 4
* If monitors are connected as shown above, you can
execute a command like “Set all monitors’ input settings to
PC1 DVI-D”.
Repeater control command
„
Repeater control is achieved by setting the FOURTH
CHARACTER of the parameter to “+”.
Example:
Sets volume of all monitors to 30.
VOLM030 +
←
In repeater control, responses are returned by all the
connected monitors.
If you want to determine that a value has been returned by a
specific set, assign ID numbers to each monitor in advance.
When some monitors do not return their responses, the
probable cause is that the monitors could not receive the
command or command processing is not complete. Do not
send a new command.
Example: (When 4 monitors are connected, and
assigned ID numbers: 1 through 4)
VOLM030 +
WAIT
OK
OK
OK
OK
001
002
003
004
If 4 monitors are connected in
a chain, reliable operation can
be ensured by sending a new
command only after a reply
has been returned by 4th (last)
monitor.
←
Repeater control can also be used for reading settings.
Example:
VOLM ? ? ? +
WAIT
10
20
30
30
001
002
003
004
Volume settings for all
monitors are returned.
TIPS
• If repeater control is used during ID designation (IDSL,
IDLK), the ID designation is canceled.
E
15
Controlling the Monitor with a PC (RS-232C)
RS-232C command table
How to read the command table
Command:
Direction:
Command field (See page 12.)
W When the “Parameter” is set in the parameter field (see page 12), the command functions as described
under “Control/Response Contents”.
R The returned value indicated under “Reply” can be obtained by setting “????”, “
(repeater control) in the parameter field (see page 12).
Parameter field (See page 12.)
Response (Returned value)
“A” indicates a command which can be used in power standby mode regardless of the STANDBY MODE
setting.
?” or “???+”
Parameter:
Reply:
*:
“B” indicates command which can be used in power standby mode when STANDBY MODE is set to
STANDARD. (It cannot be used in the power standby mode when LOW POWER is selected.)
“–” indicates a command which cannot be used in power standby mode.
Power control/Input mode selection
Function
Command
Direction
Parameter
Reply
Control/Response contents
Switches to standby mode.
*
POWER CONTROL
POWR
W
0
1
Returns from standby mode.
Standby mode
R
0
1
2
A
Normal mode
Input signal waiting mode
INPUT MODE SELECTION
INPS
W
0
1
Toggle change for input mode. Terminals not selected in DVI SELECT/
BNC SELECT/HDMI SELECT cannot be selected.
PC1 DVI-D
“ERR” when AV1 DVI-D is selected for DVI SELECT.
2
3
PC3 D-SUB
AV3 COMPONENT
“ERR” when PC4 RGB is selected for BNC SELECT.
4
6
AV5 VIDEO
A
PC4 RGB
“ERR” when AV3 COMPONENT is selected for BNC SELECT.
7
AV1 DVI-D
“ERR” when PC1 DVI-D is selected for DVI SELECT.
8
9
AV4 S-VIDEO
AV2 HDMI
“ERR” when PC2 HDMI is selected for HDMI SELECT.
10
PC2 HDMI
“ERR” when AV2 HDMI is selected for HDMI SELECT.
R
1
2
3
4
6
7
8
9
PC1 DVI-D
PC3 D-SUB
AV3 COMPONENT
AV5 VIDEO
PC4 RGB
A
AV1 DVI-D
AV4 S-VIDEO
AV2 HDMI
10 PC2 HDMI
SCREEN menu
Function
Command
ASNC
CLCK
Direction
Parameter
Reply
Control/Response contents
When the input mode is PC3, PC4.
*
AUTO
W
1
CLOCK
PHASE
WR
WR
WR
0-1200
0-63
0-1200 When the input mode is PC3, PC4. Varies depending on the signal.
0-63 When the input mode is PC3, PC4.
PHSE
POSITIONING
POSITION OF
HPOS
0-100
0-100 0-800 on PC3/PC4.
THE LONGEST
DIRECTION
Varies depending on the signal.
POSITION OF
THE SHORTEST
DIRECTION
VPOS
HSIZ
VSIZ
WR
WR
WR
0-100
0-100
0-100
0-100 0-200 on PC3/PC4.
Varies depending on the signal.
-
SIZE
POSITION OF
THE LONGEST
DIRECTION
0-100
POSITION OF
THE SHORTEST
DIRECTION
0-100
RESOLUTION
RESET
L-DIRECTION RES HRES
S-DIRECTION RES VRES
WR
WR
300-1920
200-1200
300-1920 When the input mode is PC3, PC4.
Only even numbers are valid for parameters.
200-1200
Varies depending on the signal.
ARST
W
1
E
16
Controlling the Monitor with a PC (RS-232C)
PICTURE menu
Function
Command
AGIN
Direction
Parameter
Reply
Control/Response contents
When the input mode is PC3, PC4.
0-60 0-127 on PC3/PC4.
*
AUTO
W
1
-
CONTRAST
BLACK LEVEL
TINT
CONT
BLVL
WR
WR
WR
WR
WR
WR
WR
WR
WR
WR
0-60
0-60
0-60
0-60
0-24
0-2
0-60 0-127 on PC3/PC4.
TINT
0-60
0-60
0-24
B
B
COLORS
COLR
SHRP
FLES
SHARPNESS
ADVANCED
(When the input
mode is AV.)
FLESH TONE
3D-NR
0-2 0: OFF, 1: LOW, 2: HIGH
0-2 0: OFF, 1: LOW, 2: HIGH
0-1 0: OFF, 1: ON
TDNR
MPNR
YCSP
CMHR
CMHY
CMHG
CMHC
CMHB
CMHM
CRST
CMSR
CMSY
CMSG
CMSC
CMSB
CMSM
CRST
CMVR
CMVY
CMVG
CMVC
CMVB
CMVM
CRST
BMOD
0-2
MPEG-NR
3D-Y/C
0-1
0-1
0-1 0: OFF, 1: ON (When the input mode is AV5)
C.M.S.-HUE
-10-10
-10-10
R
Y
G
C
B
M
W
1
Resets the hue.
C.M.S.-
SATURATION
WR
-10-10
-10-10
R
Y
G
C
B
B
M
W
2
Resets the saturation.
C.M.S.-VALUE
WR
-10-10
-10-10
R
Y
G
C
B
M
W
3
Resets the brightness.
STD
COLOR MODE
WR
0
2
0
2
3
0
VIVID
B
B
3
sRGB (When the input mode is PC)
When the input mode is PC1/PC2.
WHITE BALANCE THRU
PRESET
CTMP
WR
0
1-15
1-15 From 1: approximately 3,000K to 15: approximately 10,000K
(500K steps)
USER
99
0-512
0-512
0-512
0
99
R-CONTRAST
G-CONTRAST
B-CONTRAST
CRTR
CRTG
CRTB
CPTU
GAMM
ARST
WR
WR
WR
W
0-512 “ERR” when CTMP is not set to 99.
0-512
0-512
COPY TO USER
GAMMA
Copies a preset value to the user setting.
0-2 0: 1.8, 1: 2.2, 2: 2.4
-
B
-
WR
W
0-2
RESET
2
AUDIO menu
Function
Command
AUTR
AUBS
AUBL
Direction
WR
Parameter
Reply
Control/Response contents
*
TREBLE
-10-10
-10-10
-10-10
3
-10-10
-10-10
-10-10
BASS
WR
B
-
BALANCE
WR
RESET
ARST
W
E
17
Controlling the Monitor with a PC (RS-232C)
SETUP menu
Function
Command
OSDH
OSDV
SCSV
MTIM
Direction
Parameter
Reply
Control/Response contents
*
OSD H-POSITION
WR
0-100
0-100
0-100
B
OSD V-POSITION
SCREEN MOTION
MOTION TIME 1
MOTION TIME 2
WR
0-100
WR
0-4
0-4 0: OFF, 1-4: PATTERN1-4
0-20
B
B
WR
0-20
PATTERN1
MINT
WR
10-990
10-990 Per 10 seconds
5-20 Per second
B
B
PATTERN2-4
MINT
WR
5-20
0-1
14
1
MONITOR
STDR
LANG
WR
0-1 0: LANDSCAPE, 1: PORTRAIT
14 ENGLISH
LANGUAGE
WR
1
2
3
4
5
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
2
3
B
4
5
РУССКИЙ
6
0-1
6
HDMI AUTO VIEW
Power On Delay
HDAW
PWOD
WR
WR
0-1 0: OFF, 1: ON
OFF
B
B
0
0
1-60
0-1
1-60 ON
STANDBY MODE
STBM
CTLS
CMDM
IDST
WR
WR
WR
W
0-1 0: STANDARD, 1: LOW POWER
0-1 0 : RS-232C 1 : LAN
B
B
B
RS-232C/LAN SELECT
0-1
RS-232C/LAN COMMAND
0-2
0-2 0 : NORMAL, 1 : MODE1, 2 : MODE2
Sets the monitor’s ID number. (“0” means “no ID number”.)
0-255 Returns the monitor’s ID number.
ID NUMBER
ID NO. SETTING
0-255
R
ID NO. SETTING
(ONCE)
IDSL
IDLK
IDCK
W
1-255
Sets a monitor ID number.
This ID number is only effective for the command immediately after this
command.
A
B
0
Clears the ID number if one has been designated.
ID NO. SETTING
(SUBSEQUENT)
W
W
1-255
Sets a monitor ID number.
This ID number is effective for the next and all subsequent commands
after this command.
0
0
Clears the ID number if one has been designated.
ID CHECK
ID
: xxx
Displays monitor’s own ID number and the selected ID number on the
screen.
IDLK : yyy
OPTION menu
Function
Command
Direction
Parameter
Reply
Control/Response contents
*
DATE/TIME SETTING
DATE
WR
AABBCCDDEE
ABCDEFFGGH
AABBCCDDEE
AA: Year, BB: Month, CC: Day, DD: Time, EE: Minute
B
SCHEDULE
SC01-
SC08
WR
ABCDEFFGGH
Schedule of a specified number
A: Schedule
B: Power
0= Not effective, 1 = Effective
0 = OFF, 1 = ON
C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day
D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
B
E: Day of the week 3 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
F: Time
G: Minute
H: Input
00-23
00-59
0 = Not specified, 1 = PC1/AV1, 2 = PC3,
3 = PC4/AV3, 4 = AV5, 5 = AV4, 6 = PC2/AV2
INPUT SELECT
AUDIO OUTPUT
DVI SELECT
DVSL
BNSL
HDSL
WR
WR
WR
WR
WR
R
0-1
0-1 0: PC1 DVI-D, 1: AV1 DVI-D
0-1 0: PC4 RGB, 1: AV3 COMPONENT
0-1 0: PC2 HDMI, 1: AV2 HDMI
0-1 0: DIGITAL, 1: ANALOG
B
B
B
B
B
BNC SELECT
HDMI SELECT
0-1
0-1
0-1
0-1
HDMI AUDIO SELECT HMDA
AOUT
0-1 0: VARIABLE, 1: FIXED
INPUT
RESOLUTION
(PC)
RESOLUTION CHECK PXCK
-
1
2
3
5
6
7
8
9
Returns current resolution in the form of hhh, vvv.
768) 1360 x 768
PIXEL SETTING
(PC3, PC4)
PXSL
WR
1
2
768) 1280 x 768
3
768) 1024 x 768
5
480) 848 x 480
-
6
480) 640 x 480
7
1050) 1680 x 1050
1050) 1400 x 1050
768) AUTO
8
9
10
10 480) AUTO
INPUT RESOLUTION (AV) RESOLUTION CHECK RESO
R
-
480i, 480p, 1080i, 720p, 1080p, VGA , etc.
-
SCAN MODE
SCAN
AADJ
PMNG
AINC
WR
WR
WR
WR
WR
0-2
0-1
0-1
0-1
0-5
0-2 0: MODE1, 1: MODE2, 2: MODE3 (When the input mode is AV)
0-1 0: OFF, 1: ON
B
B
B
B
B
SELF ADJUST
POWER MANAGEMENT
AUTO INPUT CHANGE
COLOR SYSTEM
0-1 0: OFF, 1: ON
0-1 0: OFF, 1: ON
CSYS
0-5 0: AUTO, 1: PAL, 2: PAL-60, 3: SECAM, 4: NTSC3.58, 5: NTSC4.43
E
18
Controlling the Monitor with a PC (RS-232C)
ENLARGE menu (When the input mode is PC)
Function
Command
Direction
Parameter
Reply
Control/Response contents
0-4 0: OFF, 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5
*
ENLARGE MODE
EMAG
WR
0-4
EMHV
WR
11-55
11-55 1 x 1 (OFF) to 5 x 5 (“m x n” is expressed as “mn”, where m and n are
the numbers of monitors specified for the longest direction and the
shortest direction respectively.)
BEZEL WIDTH
WIDTH OF THE
SHORTER SIDE
BEZH
BEZV
WR
WR
0-100
0-100
0-100
WIDTH OF THE
LONGER SIDE
0-100
IMAGE POSITION (M x N)
IMAGE POSITION (2 x 2)
IMAGE POSITION (3 x 3)
IMAGE POSITION (4 x 4)
IMAGE POSITION (5 x 5)
EPHV
EPOS
EPOS
EPOS
EPOS
EPSH
WR
WR
WR
WR
WR
WR
11-55
0-3
11-55 Specify values in the order of ENLARGE-POS LD/ENLARGE-POS SD.
0-3 See the description below.
0-8
0-8
0-15
0-24
-
0-15
0-24
ENLARGED
SCREEN
THE LONGEST
DIRECTION
-999-999
-999-999 The setting range depends on the ENLARGE MODE setting and the
IMAGE POSITION.
POSITIONING
THE SHORTEST
DIRECTION
EPSV
WR
WR
WR
-999-999
XXYY
-999-999
ENLARGE/IMAGE POSITION SETTING ESTG
XXYY XX: ENLARGE MODE (Same as EMAG), YY: IMAGE POSITION (Same
as EPOS)
ESHV
XXYY
XXYY XX: ENLARGE MODE (Same as EMHV), YY: IMAGE POSITION (Same
as EPHV)
• IMAGE POSITION (EPOS) setting
In horizontal orientation
2 x 2
3 x 3
4 x 4
5 x 5
0
1
3
0
3
6
1
4
7
2
5
8
0
4
3
7
0
5
1
3
4
2
7
1
5
2
6
2
6
8
9
8
9
10
14
11
15
10
15
20
11
16
21
12
17
22
13
18
23
14
19
24
13
12
In vertical orientation
2 x 2
3 x 3
4 x 4
5 x 5
2
0
6
7
8
3
4
5
0
12
8
4
5
6
7
0
20
15
10
5
6
7
8
9
0
1
1
2
9
21
16
17
18
19
11
12
13
14
13
1
3
1
14
2
22
2
10
11
23
24
3
4
15
3
E
19
Controlling the Monitor with a PC (RS-232C)
PIP/PbyP menu
Function
Command
Direction
Parameter
Reply
Control/Response contents
*
PIP MODES
PIP SIZE
MWIN
WR
WR
W
0-3
0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2
1-12
B
B
B
B
B
B
MPSZ
1-12
PIP POS
THE LONGEST
DIRECTION
MHPS
0-100
R
0-100
0-100
THE SHORTEST
DIRECTION
MVPS
MPOS
W
0-100
R
PIP POS LD+SD BATCH
W
0-100,0-100
Specify the position in MPOSxxxyyy format.
(xxx: Longer side, yyy: Shorter side position)
B
R
0-100,0-100 Returns a response in (xxx,yyy) format.
(xxx: Longer side, yyy: Shorter side position)
B
B
PIP BLEND
MWBL
MWIP
WR
WR
0-15
1
0-15
PIP SOURCE
1
2
3
4
6
7
8
9
PC1 DVI-D
2
PC3 D-SUB
AV3 COMPONENT
AV5 VIDEO
PC4 RGB
3
4
6
B
7
AV1 DVI-D
8
AV4 S-VIDEO
AV2 HDMI
9
10
1-2
0-1
0-2
0-1
10 PC2 HDMI
SOUND CHANGE
MAIN POS (Main screen)
PbyP2 POS (Sub screen)
AUTO OFF
MWAD
MWPP
MW2P
MOFF
WR
WR
WR
WR
1-2 1: MAIN, 2: SUB
B
B
B
B
0-1 0: POS1, 1: POS2
0-2 0: POS1, 1: POS2, 2: POS3
0-1 0: MANUAL, 1: AUTO
Initialization/Functional Restriction Setting (FUNCTION) menu
Function
Command
RSET
ALCK
LOSD
OFLD
TALT
Direction
Parameter
Reply
Control/Response contents
0: ALL RESET 1, 1: ALL RESET 2
0-2 0: OFF
*
ALL RESET
W
0-1
0-2
0-1
0-1
0-2
0-2
-
ADJUSTMENT LOCK
OSD DISPLAY
WR
WR
WR
WR
WR
B
B
B
B
B
0-1 0: ON, 1: OFF
0-1 0: ON, 1: OFF
LED
TEMPERATURE ALERT
STATUS ALERT
0-2 0: OFF, 1: OSD & LED, 2: LED
0-2 0: OFF, 1: OSD & LED, 2: LED
SALT
Others
Function
Command
WIDE
WIDE
VOLM
MUTE
INF1
Direction
WR
WR
WR
WR
R
Parameter
Reply
Control/Response contents
*
B
B
B
-
SCREEN SIZE (PC)
SCREEN SIZE (AV)
VOLUME
1-5
1-5
1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2
1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot
0-31
0-1
0-31
0-1 0: OFF, 1: ON
Value
MUTE
INFORMATION
MODEL
SERIAL NO
A
B
SRNO
VLMP
DSTA
R
Value
BRIGHT
WR
R
0-31
0-31 Brightness
TEMPERATURE SENSOR
0
1
2
Internal temperature normal
Internal temperature abnormal (Standby mode)
Internal temperature abnormal (Temperature is normal now, but it was
abnormal during operation.)
A
A
3
4
Internal temperature abnormal (Brightness of the backlight decreases.)
Temperature sensor abnormal
TEMPERATURE ACQUISITION
ERRT
STCA
R
Value Temperature at temperature sensors 1 through 3 are returned in the
following forms:
[Sensor 1], [Sensor 2], [Sensor 3]
Indicates a temperature sensor abnormality when “126” is returned.
CAUSE OF LAST STANDBY MODE
W
R
0
Initialization
0
1
2
3
4
6
8
No detectable error has occurred
Standby mode by POWER button
Main power “OFF” by the main power switch
Standby mode by RS-232C or LAN
A
Waiting mode by No Signal (Incl: VESA DPMS/DMPM)
Standby mode by abnormal temperature
Standby mode by SCHEDULE setting
E
20
Controlling the Monitor with a PC (LAN)
Your monitor can be connected to a LAN allowing you to
control it from a PC on the LAN.
Settings to connect to a LAN
You can also configure the monitor to send e-mail notification
when it has a problem.
Set the monitor’s IP address and subnet mask to match the
settings of your LAN.
The connection requires a commercially available LAN cable
(UTP cable, Category 5, straight through).
These settings can be made on either the monitor or a PC
connected to the monitor.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
Network (LAN)
To set on the monitor
„
Set RS-232C/LAN SELECT on the SETUP menu to LAN, and
then set the LAN SETUP options. (See page 7.)
After setting each item, select SET and press MENU
.
LAN terminal
Hub
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to ON.
To set the address manually, set this to OFF.
IP ADDRESS
LAN cable (commercially available, straight)
If the DHCP CLIENT is set to OFF, specify an IP address.
Press
or
to select items, and press
or
to
change the values.
TIPS
SUBNET MASK
• You must assign an IP address to the monitor by following
the procedures in “Settings to connect to a LAN”. (See the
description on the right.)
If the DHCP CLIENT is set to OFF, specify the subnet mask.
Press
or
to select items, and press
or
to
change the values.
• Your PC must be installed with Internet Explorer (version 6.0
or later).
• To control the monitor via LAN, set RS-232C/LAN SELECT
to LAN. (See page 7.)
DEFAULT GATEWAY
If the DHCP CLIENT is set to OFF, specify the default
gateway.
If you are not using a gateway, specify “0.0.0.0”.
• You cannot use RS-232C and LAN control simultaneously.
Press
or
to select items, and press
or
to
change the values.
RESET
Resets the values of the LAN settings to the factory preset
values.
Select ON and then press MENU
.
E
21
Controlling the Monitor with a PC (LAN)
To set from a PC
When the monitor is connected to a PC, LAN settings can be
configured via PC.
7. Temporarily change the IP address and subnet mask.
To access the monitor as it is shipped from the factory, set
as follows.
„
• IP Address: 192.168.150.3
• Subnet Mask: 255.255.255.0
• Default Gateway: (leave blank)
Set up process
(1) Connect your monitor to a PC
(2) Specify the PC’s IP address
(3) Configure the monitor’s LAN settings
(1) Connecting your monitor to a PC
Connect a commercially available crossover LAN cable
(UPT cable, Category 5) to the LAN port on the PC and this
monitor.
8. Click [OK] and then reboot the PC.
LAN terminal
TIPS
• This monitor is factory preset as shown below.
IP Address
Subnet Mask
: 192.168.150.2
: 255.255.255.0
PC
Default Gateway : 0.0.0.0
To LAN terminal
(3) Configuring the monitor’s LAN settings
Access the monitor using Internet Explorer.
LAN cable (commercially available, crossover)
Controlling the monitor
(2) Specifying the PC’s IP address
To configure the monitor’s LAN settings, you must temporarily
change the settings on the PC.
1. Turn the power ON to the monitor.
2. Set RS-232C/LAN SELECT on the SETUP menu to LAN.
This explanation is based on Windows XP.
1. Log on to the PC with an administrator account.
2. Click [Start], and then click “Control Panel”.
3. Click “Network and Internet Connections”, and then click
“Network Connections”.
PC operation
3. Launch Internet Explorer, in the “Address” box type
If you are using the classic display style, double-click on
“Network Connections”.
4. Right click on “Local Area Connection” and from the menu,
click “Properties”.
5. Click “Internet Protocol (TCP/IP)”, and then click
“Properties”.
You will be prompted to enter a user name and password.
4. Leave the user name and password boxes blank and click
[OK].
6. Make a note of the current IP address, subnet mask, and
default gateway settings.
Make sure you write this information now as you will
be changing the IP address, subnet mask, and default
gateway settings back to these settings afterwards.
E
22
Controlling the Monitor with a PC (LAN)
5. Click on “LAN SETUP” under NETWORK.
Controlling with a PC
Basic operation
„
You use Internet Explorer on a PC on the LAN to control the
monitor.
1. Launch Internet Explorer on the PC.
IP address followed by “/”, then press the Enter key.
When prompted to enter a user name and password, type
the user name and password that you specified in the
security settings (see page 25), and click [OK].
If you did not make any security settings, leave the spaces
blank and click on [OK].
3. You can check, control, and change the monitor’s status
and settings by clicking the menu items on the left side of
the screen.
6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
• If you see an [Apply] button next to a setting, click it after
you change that setting.
IP ADDRESS
If the DHCP CLIENT is set to “OFF”, specify an IP
address.
TIPS
SUBNET MASK
• See pages 24 to 28 for details on each setting.
• If you click [Refresh] before the screen finishes updating
the current display, the “Server Busy Error” will appear.
Wait for a moment before operating your monitor again.
• You cannot operate the monitor while it is warming up.
If the DHCP CLIENT is set to “OFF”, specify the subnet
mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to “OFF”, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
• If “DHCP CLIENT” is set to “ON”, press DISPLAY on the
remote control unit two times and then check the monitor’s
IP address.
7. When the setting is changed, click [Apply].
8. Check the message and click [OK].
9. Exit Internet Explorer.
10. Restore the PC’s IP address jotted in Step 6, “(2)
Specifying the PC’s IP address”.
11. Connect the monitor and the PC to the LAN.
Caution
• Wait 10 seconds after clicking [OK] before proceeding.
• When operating using the remote control unit or similar,
click [Refresh].
E
23
Controlling the Monitor with a PC (LAN)
INFORMATION
ADJUSTMENT
„
„
Information about this monitor appears.
You can adjust these settings which are also available on the
monitor’s menu.
• SCREEN (See page 6.)
• PICTURE (See Page 6.)
• PICTURE (ADVANCED) (See Page 6.)
• AUDIO (See page 6.)
• SETUP (See page 7.)
• OPTION (See page 7.)
• SCHEDULE (See page 9.)
• ENLARGE (See page 9.)
• PIP/PbyP (See page 8.)
• FUNCTION (See page 11.)
CONTROL
„
You can control the operations corresponding to the buttons
POWER INPUT
(
SIZE ) on the remote control unit. (See page 3.)
TIPS
• In standby mode, Power ON is the operation available.
E
24
Controlling the Monitor with a PC (LAN)
NETWORK (SECURITY)
NETWORK (LAN SETUP)
„
„
This screen allows you to set the settings necessary when the
This screen allows you to specify the security-related settings.
monitor is connected to a LAN.
USER NAME / PASSWORD
DHCP CLIENT
Sets up a user name and password to restrict access to this
monitor.
After entering a user name and password, click [Apply].
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
ACCEPT IP ADDRESS
IP ADDRESS
You can limit access to this monitor by registering IP
addresses of PCs that should have access.
To limit access, specify the option “From only specific IP
addresses”. Otherwise, to allow access from any PC, specify
“All IP Addresses”.
If the DHCP CLIENT is set to “OFF”, specify an IP address.
SUBNET MASK
If the DHCP CLIENT is set to “OFF”, specify the subnet
mask.
IP ADDRESS 1 to 3
DEFAULT GATEWAY
If “ACCEPT IP ADDRESS” is set to “From only specific IP
addresses”, enter the IP addresses that you want to allow.
If the DHCP CLIENT is set to “OFF”, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
TIPS
DNS SERVER
• The USER NAME and PASSWORD can be up to 8
alphanumeric characters or symbols.
Specify the DNS server address.
If you are not using a DNS server, specify “0.0.0.0”.
• To cancel the user name and/or password after it has been
set, make the box empty and click [Apply].
RESET
Clicking [Execute] returns all of the LAN SETUP settings
to the factory-preset values except for the DNS SERVER
setting.
E
25
Controlling the Monitor with a PC (LAN)
NETWORK (GENERAL)
MAIL (ORIGINATOR)
„
„
This screen allows you to specify the general LAN settings.
This screen allows you to configure the e-mail sent periodically
or when the monitor has an error.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
SMTP SERVER
Specify the SMTP server address for sending e-mail.
* When using a domain name, make sure to specify the
DNS server as well. (See page 25.)
MONITOR NAME
Specify a name for this monitor as it should appear on the
Internet Explorer screen.
ORIGINATOR E-MAIL ADDRESS
AUTO LOGOUT TIME
Specify the e-mail address for this monitor.
This address becomes the e-mail address of the originator.
Specify the time (in minutes) to elapse before automatically
disconnecting this monitor from the network.
Specify in minutes from 1 to 65535. A value of ‘0’ will disable
this function.
ORIGINATOR NAME
Specify the name for the originator.
This name appears in the “Originator Name” field of the
e-mail.
DATA PORT
Specify the TCP port number to use for exchanging data with
the monitor.
Specify a value from 1025 to 65535.
AUTHENTICATION
Specify the authentication method to use when sending
e-mail.
SEARCH PORT
POP SERVER
Specify the port number to use when searching for this
monitor.
Specify a value from 1025 to 65535.
If the “AUTHENTICATION” method is “POP before SMTP”,
specify the POP server address.
ACCOUNT NAME / PASSWORD
TIPS
If the “AUTHENTICATION” method is “POP before SMTP”,
specify the account name and password to connect to the
POP server.
• The MONITOR NAME can be up to 16 alphanumeric
characters or symbols.
TIPS
• You can enter up to 64 alphanumeric characters or symbols
for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR
NAME, ACCOUNT NAME, and PASSWORD.
• The SMTP SERVER and POP SERVER can be up to 64
characters.
The following characters can be used: a-z, A-Z, 0-9, - , .
E
26
Controlling the Monitor with a PC (LAN)
MAIL (PERIODICAL)
MAIL (RECIPIENT)
„
„
This screen allows you to specify the recipients of the e-mail
When PERIODICAL for CONDITION of MAIL (RECIPIENT) is
sent periodically or when the monitor has an error.
checked, set the date and time to send the mail.
RECIPIENT E-MAIL ADDRESSES
DAY OF THE WEEK
Specify the e-mail addresses to send error notification e-mail
to.
Specify the day of the week to send the periodical mails.
TIME
CONDITION
Specify the time of the day to send the periodical mails.
Specify the conditions to send mails.
When you check PERIODICAL, specify the date and time to
send the mails in the PERIODICAL setting.
Caution
• Do not turn off the main power when you set to send the
periodical mails.
CONFIRMATION
Sends test e-mail.
This allows you to confirm that the e-mail settings are
configured properly.
• Specify the correct date and time. (See page 7.)
If the date and time settings are incorrect, the periodical
mail is not sent properly.
• Regularly confirm that the specified date and time is
correct.
Attach the log file to a TEMPERATURE/HARDWARE error
e-mail
When this option is checked, a log is added to the mail which
notifies a temperature or status error.
TIPS
• The RECIPIENT E-MAIL ADDRESSES can be up to 64
alphanumeric characters or symbols.
E
27
Controlling the Monitor with a PC (LAN)
SERVICE & SUPPORT
(URL INFORMATION)
„
You can display a specific URL in the URL INFORMATION
field on the INFORMATION screen when an error occurs in
the monitor. (See page 24.)
URL INFORMATION
Enter a URL to display when an error occurs on the monitor.
Up to 64 alphanumeric characters or symbols can be used.
CONDITION
Specify the condition to display the URL.
CONFIRMATION
The home page of the specified URL is displayed.
You can check whether the URL you entered is correct.
TIPS
• It is also possible to specify the message text, such as the
name of a contact or a telephone number, to be displayed
instead of the linked URL.
E
28
M E M O
E
29
MITSUBISHI Contact Information
North America
Europe
MESCA (Mitsubishi Electric Sales Canada Inc.)
Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2,
Canada
MEU-FRA (Mitsubishi Electric Europe B.V French Branch)
25, Boulevard des Bouvets 92 741, Nanterre CEDEX, France
Sales
Phone
Fax
:+33 (0)1 55-68-55-07
:+33 (0)1 55-68-57-31
:+33 (0)1 55-68-56-42
:+33 (0)1 55-68-57-31
Sales
Phone
Fax
:+1-(905) 475-7728
:+1-(905) 475-7958
Technical
Phone
Fax
E-mail
Phone
Fax
:+1-(905) 475-7728
MEU-GER(Mitsubishi Electric Europe B.V. German Branch)
Technical
:+1-(905) 475-7958
Gothaer Strasse 8, 40880 Ratingen, Germany
Customer Care
MEU-IR(Mitsubishi Electric Europe B.V. Irish Branch)
Westgate Business Park, Ballymount, Dublin 24, Ireland
E-mail
MDEA (Mitsubishi Digital Electronics America, Inc.)
(Warranty Registration)
Presentation Products Division, 9351 Jeronimo Road, Irvine, CA 92618 U.S.A
Sales
Phone
Fax
Phone
Fax
:+353-(0)1- 4198844
:+353-(0)1-4564422
:+353-(0)1-4198807
:+353-(0)1-4198895
Technical
Phone
Main Line
Technical
Product Information
:+1-(949) 465-6000
:+1-(888) 307-0309
:+1-(888) 307-0312
MEU-IT(Mitsubishi Electric Europe B.V. Italian Branch)
Centro Direzionale Colleoni, Palazzo Persero-Ingresso 2, Via Paracelso 12, 20041
Agrate Brianza, Italy
Technical Support
E-mail
Sales
Phone
Fax
E-mail
:+39-(0)39-60531
:+39-(0)39-6053214
MEU-NL(MitsubishiElectric Europe B.V. Benelux Branch)
Nijverheidsweg 23a, 3641 RP Mijdrecht, The Netherlands
Sales
Phone
Fax
:+31-297-282461
:+31-297-283936
:+31-297-282461
:+31-297-283936
E-mail
Phone
Fax
Technical
E-mail
MEU (MITSUBISHI ELECTRIC EUROPE B.V.)
Moscow Representative Office, 12/1 Goncharnaya St. 109240, Moscow, Russia
Sales
Phone
Fax
:+7 (095) 915 8602
:+7 (095) 915 8603
MEU-SP(Mitsubishi Electric Europe B.V. Spanish Branch)
Ctra. de Rubi, 76-80, 08190 Sant Cugat del Valles, Barcelona, Spain
Sales
Phone
Fax
:+34-93.565.31.54
:+34-93.589.43.88
E-mail
Phone
Fax
:+34-93.586.27.51
Technical
:+34-93.699.74.45
E-mail
MEU-SWE(Mitsubishi Electric Europe B.V Scandinavian Branch)
Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden
Sales
Phone
Fax
Phone
Fax
:+46-(0)8-6251070
:+46-(0)8-6251036
:+46-(0)8-6251052
:+46-(0)8-6251036
Technical
MEU-UK(Mitsubishi Electric Europe)
Visual Information Systems Division, Travellers Lane, Hatfield, Hertfordshire, AL10 8XB
Sales
Phone
Fax
:+44 (1707) 278684
:+44 (1707) 278541
E-mail
Phone
Fax
:+44 (870) 606 5008
Technical
:+44 (1506) 431927
E-mail
Russia (Mitsubishi Electric Europe B.V Moscow Representative Office)
52, bldg.5, Kosmodamianskaya Nab, 113054, Moscow, Russian Federation
Sales
Phone
Fax
Phone
Fax
:+7 (095) 721 2070
:+7 (095) 721 2071
:+7 (095) 721 2070
:+7 (095) 721 2071
Technical
|