V-LCD70P-HDA
7” High Resolution Field Monitor
Operating Instructions
Contents
Product Overview .................................................................................................................................................................................4
Features...................................................................................................................................................................................................4
Installation and Initial Setup...............................................................................................................................................................5
Unpacking...........................................................................................................................................................................5
Mounting .............................................................................................................................................................................5
Changing the Battery Adapter ............................................................................................................................................5
Connections and Power-On................................................................................................................................................5
Front and Side Panel Features..........................................................................................................................................................6
Power Button ......................................................................................................................................................................6
Menu Navigation Buttons....................................................................................................................................................6
User-Definable Function Buttons........................................................................................................................................6
Menu Navigation Buttons....................................................................................................................................................6
Image Adjustment Knobs....................................................................................................................................................6
Power Switch ......................................................................................................................................................................6
Power Switch ......................................................................................................................................................................6
Rear Panel Features.............................................................................................................................................................................7
Component and Composite Input and Output....................................................................................................................7
Power Input.........................................................................................................................................................................7
Battery Adapter...................................................................................................................................................................7
1/4-20 Mounting Hole .........................................................................................................................................................7
Compatible Input Formats..................................................................................................................................................................8
On-Screen Menu....................................................................................................................................................................................9
STRUCTURE OVERVIEW .................................................................................................................................................9
MAIN MENU AND NAVIGATION .......................................................................................................................................9
VIDEO CONFIGURATION SUBMENU ............................................................................................................................10
Color Temperature Presets.............................................................................................................................................................10
RGB Bias and Gain.........................................................................................................................................................................10
Check Field.....................................................................................................................................................................................11
Aspect Ratio Setting .......................................................................................................................................................................11
Pixel-to-Pixel Mode.........................................................................................................................................................................12
H/V Delay........................................................................................................................................................................................12
Underscan ......................................................................................................................................................................................12
NTSC Black Level...........................................................................................................................................................................12
MARKER CONFIGURATION SUBMENU ........................................................................................................................13
Markers...........................................................................................................................................................................................13
Center Marker.................................................................................................................................................................................13
16:9 Markers / Full Screen Markers................................................................................................................................................13
4:3 Markers.....................................................................................................................................................................................14
Marker Background.........................................................................................................................................................................14
FILTER CONFIGURATION SUBMENU ...........................................................................................................................15
False Colors....................................................................................................................................................................................15
Peaking Filter (Focus Assist) ..........................................................................................................................................................16
Mosquito Filter ................................................................................................................................................................................16
SYSTEM CONFIGURATION SUBMENU.........................................................................................................................17
Input Format OSD...........................................................................................................................................................................17
User-Definable Function Buttons....................................................................................................................................................17
Freeze Input....................................................................................................................................................................................17
Manufacturer Default ......................................................................................................................................................................17
Specifications ......................................................................................................................................................................................18
Maintenance.........................................................................................................................................................................................19
Warranty................................................................................................................................................................................................19
3
Product Overview
The V-LCD70P-HDA is a 7.0” high-definition widescreen LCD monitor featuring our completely digital TFT-MegaPixel
active matrix LCD platform. With built-in focus assist and false color filters, this monitor is ideal as a light-weight high
resolution viewfinder or focus-assist monitor. Our proprietary digital signal processing features 10-bit A/D conversion of all
analog signals, with 4X over-sampling and 5-line super-adaptive 2D comb filtering of composite signals. De-interlacing is
performed using our HyperProcess algorithm with motion adaptive interpolation. Multi-format compatibility accommodates
virtually all video formats including NTSC/PAL, 480i/p, 720p, and 1080i standards. Adjustable color temperature enables
the most precise color representation possible. Advanced features include aspect ratio settings, a variety of screen
markers, underscan mode, blue-only mode, monochrome mode, H/V delay, and Pixel-to-Pixel mode.
Features
High-Resolution 7.0” Widescreen Panel
The V-LCD70P-HDA features an all-digital TFT-MegaPixel active matrix LCD system with 1.2 million pixels. The LCD
panel features a brightness of 250 cd/m2 and a contrast ratio of 400:1 making the display ideal in a variety of
environments and lighting conditions.
Multi-Format Compatibility
The V-LCD70P-HDA accommodates virtually all video standards with Composite Video and YPbPr inputs. Accepted
formats include NTSC/PAL, 480i/p, 576i/p, 720p, 1035i, and 1080i standards.
End-to-End Digital Signal Processing
Analog input signals are digitized using an advanced 10-bit process with 4x over-sampling, 5-line super-adaptive 2D
comb filtering, and exacting color space conversion. Video is scaled to fit on the screen in the highest possible
resolution using a state-of-the-art LSI that incorporates precision gamma correction and our HyperProcess motion
adaptive interpolation for interlaced images.
ColorMatch Conversion with Color Temperature Adjustment
Emulation of SMPTE-C/EBU color space allows the V-LCD70P-HDA to replace any broadcast CRT monitor. Presets
include D55, D65 and D93. Bias and Gain adjustment for each color enables precise color matching and white
balance.
Focus-Assist, False Color Filter, and other Advanced Features
Focus-Assist, False Color filter, Aspect ratio settings, underscan mode, blue-only mode, monochrome mode, and H/V
delay are a few of the advanced features which make the V-LCD70P-HDA at home in any broadcast environment.
Pixel-to-Pixel mode also allows native display of any incoming image format.
Flexible Screen Markers
A variety of screen markers in 4:3, 16:9, and full screen modes allow accurate monitoring of the different aspect ratios
used in broadcast environments.
User-Definable Function Buttons
Four user-assignable function buttons on the front-panel allow quick access to numerous settings and features
including focus-assist, false color filter, aspect ratio, screen markers, monochrome mode, color temperature, delay
mode, and more.
User-Interchangeable Battery Adapters
Several battery adapter options accommodate a wide variety of professional batteries and camcorder batteries.
4
Installation and Initial Setup
Unpacking
Carefully unpack the V-LCD70P-HDA monitor and verify that the following items are included:
• V-LCD70P-HDA Monitor
• V-PS12-5V-XLR Power Supply with 4-Pin Female XLR Connector
• Operating Instructions
Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage,
immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States,
call +1 (310) 333-0606.
Mounting
The V-LCD70P-HDA monitor features a ¼”-20 mounting hole on the underside of the enclosure, allowing the monitor
to be flexibly mounted to a camera or other device using a variety of mounts.
Changing the Battery Adapter
The V-LCD70P-HDA ships with a single battery adapter, specified at the time of ordering. Several other batteries
adapters are available to accommodate a variety of batteries.
•
Six user-interchangeable “camcorder battery” adapters are available: Canon, Panasonic, JVC, Sony BP,
Sony NP-Q, and Sony NP-F.
Installation: To uninstall one of the above battery adapters, remove the 5 screws on the adapter. Remove
the adapter and carefully disconnect the 4-pin connector between the monitor and adapter. To install one
of the above battery adapters, connect the 4-pin connector of the new battery adapter to the monitor, and
re-install the 5 screws.
Note: Do not change the pinout of the 4-pin connector connecting the battery adapter to the monitor. This
pinout is factory-configured according to each battery adapter.
•
IDX and Anton Bauer battery adapters are available, but must be installed at the factory. Contact Marshall
Electronics for further information.
Connections and Power-On
Plug the V-PS12-5V-XLR power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 4-pin female
XLR connector to the back of the monitor. Please note that 12VDC can be also supplied directly to the monitor from a
variety of sources. The monitor will draw no more than 1.0 Amps at 12 Volts in operation (12 Watts).
Connect the required cables for video signal input and output. (Power must be applied to the V-LCD70P-HDA for the
active loop-though outputs to be activated.) All BNC connectors are rated at 75.
The unit defaults to ‘ON’ when power is supplied. Video will automatically be detected and displayed on the screen.
5
Front and Side Panel Features
Power Button
Image Adjustment Knobs
Use the power button to toggle between ON and
STANDBY modes. In the STANDBY state, the LED
on the button will illuminate bright green. In the ON
state, the LED will dimly illuminate green.
Use the image adjustment knobs to adjust color
saturation, brightness and contrast of the image.
The status of each image adjustment parameter is
shown on the bottom left of the screen, with values
ranging from 0 to 100. Pressing each knob resets
the corresponding adjustment to its default setting
(50).
Input Select Buttons
Use the VIDEO and YPbPr buttons to select the
corresponding analog input. Video standards
(NTSC/PAL, etc.) are automatically detected.
Power Switch
Use the hard power switch to supply power to the
monitor, and choose the input from which the
monitor draws power. The upper switch position
uses the battery adapter, the lower switch position
uses the XLR input, and the center position is OFF.
Battery life can be preserved by setting this switch to
the OFF position when the monitor is not in use.
User-Definable Function Buttons
Four user-definable function buttons can be used for
direct access to various settings. Functions are
assigned using the on-screen menu (See User-
Definable Function Buttons – Page 17).
Menu Navigation Buttons
Use the Menu, , , and Select buttons to display
and navigate the on-screen menu (See Main Menu
and Navigation – Page 9).
Service Connector
This connector is for factory and future use.
6
Rear Panel Features
Component and Composite Input and Output
The V-LCD70P-HDA has HD component (YPbPr)
and composite inputs, as well as an active loop-
through output for each input. See page 8 for
supported video formats. These inputs are internally
terminated with 75 ohms.
Battery Adapter
The V-LCD70P-HDA can be powered from a variety
of batteries. Several user-interchangeable battery
adapters are available. See page 18 for available
adapters.
¼-20 Mounting Hole
Power Input
Use the ¼-20 mounting hole to attach the monitor to
a camera or variety of mounting devices.
Connect 12VDC to the 4-Pin XLR power input
connector. Power can be supplied from the included
power supply, or from a variety of DC sources
supplying at least 1 Amp at 12 Volts.
IMPORTANT: If using a power source other than the
included power supply, be sure that the polarity of
the DC input is correct:
Pin 1: GND
Pin 2: N/C
Pin 3: N/C
Pin 4: +12VDC
7
Compatible Input Formats
Format
Composite
YPbPr
NTSC
PAL
480i
576i
480p / 59.94
576p / 50
720p / 60
720p / 59.94
720p / 50
720p / 30
720p / 29.97
720p / 25
720p / 24
720p / 23.98
1035i / 60
1035i / 59.94
1080i / 60
1080i / 59.95
1080i / 50
1080psF / 24
1080psF / 23.98
1080p / 30
1080p / 29.97
1080p / 25
1080p / 24
1080p / 23.98
8
On-Screen Menu
STRUCTURE OVERVIEW
Color Temperature
RGB Bias and Gain
Check Field
Ratio
D93, D65, D55, User
R, G, B Bias (0-100) / R, G, B Gain (0-100)
Off, Mono, Blue, Green, Red
Full Screen, 4:3, 16:9
Off, On
Video Configuration
Pixel-to-Pixel
H/V Delay
Off, H & V Delay, V Delay, H Delay
Off, On
Underscan
NTSC Black Level
Markers
0 IRE, 7.5 IRE
Off, On
Center Marker
Off, On
Off, 4:3, 13:9, 14:9, 1.85:1, 2.35:1, 95% Safe,
93% Safe, 90%Safe, 88% Safe, 85% Safe, 80%
Safe
16:9 Markers
Off, 4:3, 13:9, 14:9, 1.85:1, 2.35:1, 95% Safe,
93% Safe, 90%Safe, 88% Safe, 85% Safe, 80%
Safe
Marker Configuration
Full Screen Markers
4:3 Markers
Off, 95% Safe, 93% Safe, 90% Safe, 88% Safe,
85% Safe, 80% Safe
Marker Background
False Colors
Normal, Black
Off, On
Main Menu
Filter Configuration
Peaking Filter
Off, On
Mosquito Filter
Input Format OSD
Off, On
5 sec, Off, On
Ratio, Check Field, Mosquito Filter, Peaking
Filter, False Colors, Freeze Input, Aspect Markers,
Center Marker, Markers, Underscan, H/V Delay,
Pixel-to-Pixel
Function on F1
Function on F2
Function on F3
Function on F4
Ratio, Check Field, Mosquito Filter, Peaking
Filter, False Colors, Freeze Input, Aspect Markers,
Center Marker, Markers, Underscan, H/V Delay,
Pixel-to-Pixel
Ratio, Check Field, Mosquito Filter, Peaking
Filter, False Colors, Freeze Input, Aspect Markers,
Center Marker, Markers, Underscan, H/V Delay,
Pixel-to-Pixel
System Configuration
Ratio, Check Field, Mosquito Filter, Peaking
Filter, False Colors, Freeze Input, Aspect Markers,
Center Marker, Markers, Underscan, H/V Delay,
Pixel-to-Pixel
Freeze Input
Freeze, Unfreeze
Manufacturer Default
Version Number Display
Select
(Software Version Number Displayed)
MAIN MENU AND NAVIGATION
Access the main menu by pushing and holding the MENU button on the front panel of the monitor.
•
•
•
•
Step through menu items using the and buttons.
Choose a submenu or select a menu item by pressing SELECT.
Return to the previous menu by pressing MENU.
Exit the main menu by pressing MENU. The menu will automatically
time out after about 15 seconds.
Main Menu
9
On-Screen Menu (continued)
VIDEO CONFIGURATION SUBMENU
Video Configuration Submenu
Color Temperature
Use this setting to choose one of three color temperature presets:
• D55 (5500K)
• D65 (6500K)
• D93 (9300K)
• USER (Adjustable Color Bias and Gain)
RGB Bias and Gain
Select this submenu to adjust bias and gain of the monitor’s response to each color (R, G, B). The bias and gain
controls can be used to alter the white balance of the image. Note: The Color Temperature preset will automatically
switch to USER when Color Bias settings are adjusted. It is normal for color bias adjustments to be very subtle.
When selecting the RGB Bias and Gain submenu, gain adjustment indicators will appear at the top of the screen, and
bias adjustment indicators will appear at the bottom of the screen:
RGB Bias and Gain Submenu
Use the and buttons to select each individual bias or gain control. Press SELECT to begin adjusting the control. Use
the and buttons to increase or decrease the value.
Alternately, the image adjustment knobs (Brightness, Color, Tint, Contrast) can be used to easily adjust the bias and gain
settings as shown below. The knobs affect whichever row of controls (gain or bias) is currently selected.
10
RED GREENBLUE ALL
On-Screen Menu (continued)
VIDEO CONFIGURATION SUBMENU (continued)
Check Field
Use the check field modes for monitor calibration or to analyze individual color components of an image. In
Monochrome mode, all color is disabled and only a grayscale image is shown. In Blue, Green, and Red check field
modes, all color components but one are disabled.
Use the following procedure when calibrating the monitor to SMPTE color bars with the following procedure:
1.
2.
3.
4.
Allow the monitor to warm up for at least 5-10 minutes.
Display SMPTE split-field color bars on the monitor using an external source.
Enable Monochrome mode.
Locate the pluge pattern (super black, black, and gray bars) at the lower-right corner of the screen. Adjust the Brightness knob until
there is no visible difference between the super black and black bars, but the gray bar is still visible.
5.
6.
7.
8.
Adjust the Contrast knob until an even grayscale appears along the top bars.
Disable Monochrome mode.
Enable Blue Check Field mode and adjust the Color knob so that the outermost bars (white and blue) appear to match in brightness.
Composite NTSC only: Adjust the Tint knob until the third bar from the left (cyan) and the third bar from the right (magenta) appear to
match in brightness.
9.
Disable Blue Check Field mode.
Aspect Ratio Settings
Use to switch between Full Screen, 4:3 and 16:9 aspect ratios.
As the V-LCD70P-HDA monitor has a native resolution of 800 x 480 RGB pixels, incoming images are automatically
scaled to fit the screen:
•
•
In Full Screen, images are scaled to fill the entire 15x9 screen.
In 4:3 mode, images are scaled to fill the maximum 4:3 portion of the screen (640 x 480), with black bars filling the
remainder of the screen.
•
In 16:9 mode, images are scaled to fill the maximum 16:9 portion of the screen (800 x 450), with black bars filling
the remainder of the screen
16:9 Mode
Full Screen
4:3 Mode
Note: The aspect ratio setting is ignored when Pixel-to-Pixel mode is enabled.
11
On-Screen Menu (continued)
VIDEO CONFIGURATION SUBMENU (continued)
Pixel-to-Pixel Mode
Use this setting to enable Pixel-to-Pixel mode.
This mode bypasses the monitor’s internal scaling function and displays incoming images in their native resolution and
aspect ratio, with a one-to-one mapping:
•
For incoming formats smaller than the native resolution of the LCD panel (800 x 480), the image will be displayed
in the center of the screen using only the necessary LCD pixels. For example, NTSC images will occupy exactly
720 x 480 pixels. The surrounding pixels will be black.
•
For incoming formats exceeding 800 x 480 pixels, only the center 800 x 480 of the incoming image will displayed
occupying the whole screen, with the remainder of the picture cropped. For example, 1080i formats will both be
cropped to 800 x 480 and displayed full-screen.
Note: Pixel-to-Pixel mode disables aspect ratio control and H/V Delay.
H/V Delay
Use this setting to enable one of three delay modes (H & V Delay, V Delay, H Delay):
•
In H & V Delay mode, both horizontal sync and vertical sync are delayed, resulting in both horizontal and vertical
blanking periods being shown on the screen.
•
•
In V Delay mode, vertical sync is delayed so that the vertical blanking period is displayed on screen.
In H Delay mode, horizontal sync is delayed so that the horizontal blanking period is displayed on the screen.
Underscan
Use this setting to enable or disable Underscan mode:
•
•
When Underscan is OFF, the active portion of the video signal is displayed on the screen, with 0% overscan.
When Underscan is ON, the area around the active video area is displayed on the screen, resulting in blanking
intervals being shown around the perimeter of the active image. Use this mode to clearly view the edges of the
active video area.
NTSC Black Level
Set the NTSC Black Level according to the type of NTSC composite video input:
•
•
7.5 IRE: Use this setting for standard NTSC-M signals which use a 7.5 IRE setup (black level).
0 IRE: Use this setting for NTSC-J signals which have no setup, or a black level of 0 IRE.
Note: This setting is disabled for PAL composite input and all component formats.
12
On-Screen Menu (continued)
MARKER CONFIGURATION SUBMENU
Marker Configuration Submenu
Markers
Use this setting to enable or disable all on screen markers. This setting affects the center marker, full screen markers,
16:9 markers, and 4:3 markers.
Center Marker
Use this setting to display a center marker on the screen.
16:9 Markers / Full Screen Markers
Use these setting to superimpose one of 11 markers on the screen when in Full Screen mode or 16:9 mode.
•
•
•
•
•
•
•
•
•
•
•
4:3
13:9
14:9
1.85:1
2.35:1
95% Safe
93% Safe
90%Safe
88% Safe
85% Safe
80% Safe
16:9 Marker Examples:
4:3 Aspect Ratio Marker
2.35:1 Aspect Ratio
OFF (No Marker)
90% Safe Area
13
On-Screen Menu (continued)
MARKER SETUP SUBMENU (continued)
4:3 Markers
Use this setting to superimpose one of 5 markers on the screen when in 4:3 mode. This setting is disabled when the
aspect ratio is set to 16:9, or when Pixel-to-Pixel, Underscan, or H/V Delay is enabled.
• 95% Safe Area
• 93% Safe Area
• 90% Safe Area
• 88% Safe Area
• 85% Safe Area
• 80% Safe Area
4:3 Marker Examples:
OFF (No Marker)
90% Safe Area
Marker Background
Use this setting to choose how selected markers are displayed on the screen:
• Normal
• Black
The marker is superimposed on the complete image.
Image area beyond the marker is shown at 0% intensity (black).
Example (80% Marker in 4:3 Mode):
Normal Background
Black Background
14
On-Screen Menu (continued)
FILTER CONFIGURATION SUBMENU
False Colors
The V-LCD70P-HDA has a false color filter to aid the in setting camera exposure. As the camera Iris is adjusted,
elements of the image will change color based on the luminance or brightness values. This enables proper exposure to
be achieved without the use of costly, complicated external equipment. To best utilize this feature, you must
understand the color chart below and have a basic understanding of camera exposure. Normally, when shooting
subjects like people, it is common practice to set exposure of faces to the equivalent of approximately 56 IRE. The
false color filter will show this area as the color PINK on the monitor. Therefore, as you increase exposure (open the
IRIS), your subject will change color as indicated on the chart: PINK, then GREY, then a few shades of YELLOW. Over
exposed subjects (above 101 IRE) on the monitor will be shown as RED. In addition, underexposed subjects will show
as DEEP-BLUE to DARK –BLUE, with clipped-blacks indicated with a FUCHSIA-like color. Lastly, the color GREEN is
used to indicate elements of the image that are approximately 45 IRE. This represents a ‘neutral’ or ‘mid-level’
exposure commonly used for objects (not people).
False Color Key
15
On-Screen Menu (continued)
FILTER CONFIGURATION SUBMENU (continued)
Peaking Filter (Focus assist)
The Peaking Filter is used to aid the camera operator in obtaining the sharpest possible picture. When activated, all
color will be removed from the display and a black-and-white image will remain. The internal processor will display
RED color on the screen where sharp edges appear. When the camera operator adjusts (racks) the focus control (on
the camera lens), different parts of the image will have RED colored edges. This indicates that that portion of the
image is sharp – or in focus. Final focus is achieved by racking the camera lens focus control back and forth until the
desired portion of the image has RED colored edges. Please note that this feature is most effective when the subject is
properly exposed and contains enough contrast to be processed.
Mosquito Filter
Use this setting to filter out “Mosquito Noise” – an artifact that appears as specs around edges of objects. This artifact
is the result of video that has been compressed at some point. Video sources from DVD-Players, PDA’s, Digital Cable
Boxes, Camcorders, etc. often have this artifact.
16
On-Screen Menu (continued)
SYSTEM CONFIGURATION SUBMENU
System Configuration Submenu
Input Format OSD
Use this option to enable on-screen display of input/format status in the upper-left corner of the screen.
User-Definable Function Buttons
Use the Function on F1, F2, F3 and F4 menu items to define each function button on the front panel of the monitor.
The following options are available for each button:
•
•
•
•
•
•
•
•
•
•
•
•
Ratio
Check Field
Mosquito Filter
Peaking Filter
False Colors
Freeze Input
Aspect Markers
Center Marker
Markers
Underscan
H/V Delay
Pixel-to-Pixel
Freeze Input
Use the Freeze function to “freeze” the current image on the screen. Select this menu item again (Unfreeze) to return
to the real-time video input.
Manufacturer Default
Select this menu item to reset all adjustments and menu settings to the factory default configuration.
17
Specifications
PANEL
BATTERY ADAPTER
Screen Size
Display Area (h x v)
Aspect Ratio
Pixels
7.0” Diagonal
152.40 x 91.44 mm
15:9 (16:9 / 4:3 Selectable)
800 x 480
Field-Interchangeable Battery Adapter Options
(Sold Separately):
Color Depth
Viewing Angle (h x v) 140°x 100°(CR >10)
Brightness
Contrast Ratio
Dot Pitch (h x v)
Pixel Pitch (h x v)
18-bit (262,144 Colors)
Marshall
Adapter
Battery
Type
Battery
Voltage
Recommended
Battery
250 cd/m2
400:1
0.0635 x 0.1905 mm
0.1905 x 0.1905 mm
CM
Canon
7.4 V
Canon BP-970G
Panasonic CGA-D54
JVC BN-V438U
Sony BP-460
PM
JM
SB
SM
SL
Panasonic
JVC
7.2 V
7.2 V
14.4 V
7.2 V
7.2 V
Sony BP
Sony NP-Q
Sony NP-F
Sony NP-QM91
Sony NP-F970
VIDEO INPUT/OUTPUT
Video Input / Output
Supports SMPTE 170M, NTSC/PAL
Factory Configured Battery Adapter Options:
Marshall
Adapter
Battery
Type
Battery
Voltage
Recommended
Battery
YPBPR Input / Output
Supports SMPTE 260M, 274M, 296M
IDX
AB
V-Mount
Anton Bauer
14.4 V
14.4 V
IDX E7S
Anton Bauer Hytron 50
CONNECTORS
Video Input
MECHANICAL
Dimensions (w x h x d): 6.85” x 5.67” x 1.95”
Additional Mounting: ¼”-20 Mounting Bracket
Video
YPBPR
1 x BNC Female (75 )
3 x BNC Female (75 )
Video Output (Active Loop-Through)
Video
1 x BNC Female (75 )
YPBPR
3 x BNC Female (75 )
Weight (Monitor Only): 1.55 lbs
Operating Temperature 32°F to 95°F (0°C to 35°C)
Power Input
Storage Temperature
Compliance
-4°F to104°F (-20°C to 40°C)
4-Pin Male XLR
Pin 1: GND
Pin 2: N/C
Pin 3: N/C
, FCC-Class A, ANSI-63.4
(Certificates on file)
Pin 4: +12VDC
RoHs
Do not dispose. Return to
Manufacturer or Authorized
Recycle Facility.
ELECTRICAL
Power Consumption 1 Amp (Max) @ 12VDC (12 W Max)
Voltage Requirement 12VDC (10VDC-18VDC)
V-PS12-5V-XLR Power Supply:
Input
Output
100V-240V, 1.5A, 50-60Hz
12VDC, 5A, 60W Max
18
Specifications (continued)
Maintenance
Screen Cleaning
Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro-
fiber cloth can also be used using only non-abrasive and ammonia-free cleaning agents. Do not use paper towels.
Paper towel fibers are coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the
surface. Antistatic and fingerprint resistant cleaning agents are recommended. Do not apply excessive pressure to the
screen to avoid damaging the LCD.
Faceplate Dusting
Dust the unit with a soft, damp cloth or chamois. Dry or abrasive cloths may cause electrostatic charge on the surface,
attracting dust particles. Neutralize static electricity effects by using the recommended cleaning and polishing practice.
Warranty
Marshall Electronics warranties to the first consumer that this V-LCD70P-HDA LCD monitor will, under normal use, be
free from defects in workmanship and materials, when received in its original container, for a period of one year from the
purchase date. This warranty is extended to the first consumer only, and proof of purchase is necessary to honor the
warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to
honor the warranty set forth above. Therefore, labor and parts may be charged to the consumer. This warranty does not
apply to the product exterior or cosmetics. Misuse, abnormal handling, alterations or modifications in design or
construction void this warranty. It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the
periphery of the display active viewing area. Marshall Electronics reserves the option to refuse service for display pixel
failure if deemed unobtrusive to effective use of the monitor by our technicians. No sales personnel of the seller or any
other person is authorized to make any warranties other than those described above, or to extend the duration of any
warranties on behalf of Marshall Electronics, beyond the time period described above. Due to constant effort to improve
products and product features, specifications may change without notice.
19
1910 East Maple Ave.
El Segundo, CA 90245
Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688
V1.0
|