Back Panel
Marshall Lynx LCD Monitor
M-Lynx-10W
User Manual
Marshall
Industrial Video/Security Div.
For more information, contact Marshall Electronics, Industrial Video & Security (800) 800-6608
Lynx LCD Monitor User Manual
Lynx LCD Monitor User Manual
INTRODUCTION
CONNECTION
V1
R
1
2
3
4
hank you for purchasing the Marshall Lynx 10W LCD Monitor. The Lynx Se-
T
ries of Universal Monitors offers high performance features and excellent pic-
ture quality for use in a variety of industrial/commercial and mobile applications.
L
The information contained in this instruction manual covers the installation and
operation of the monitors. We encourage you to read it carefully and keep it for
future reference. All the installation materials and wire/cables must pass qual-
ity inspections in accordance with international electrical rules and laws. When
installing your monitor, remember to always adhere to local ordinances and laws
concerning wire and cable installation.
5
INSTALLATION
DC12V
We strongly recommend that a qualified installation and maintenance technician
install this product. Improper installation of this monitor may cause battery leak-
age or a short circuit.
1. Yellow 1 Video input 1
2. Red Audio Right input
3. White Audio Left input
4. Yellow 2 Video input 2 (BNC)
5. DC12V
PRECAUTIONS
Remote Control
In mobile applications, do not place the remote control in direct sunlight, especial-
ly in the summer. For example, avoid placing the remote on the dashboard, steer-
ing wheel or any other place where high temperatures could cause damage. When
parking in the sun, be sure the remote is safely stored in a glove box or tool kit.
LCD PANEL FUNCTIONS
When exposed to direct sunlight, signals emitted from the remote control may
not be properly received by the monitor. The remote should be pointed within
close proximity of the front panel receiver.
Double-sided Tape
The included double-sided tape is intended for use on a flat desktop surface
only. Do not attempt to affix the panel on other surfaces.
LCD
1
2
3
4
5
Do not press against the screen of the LCD. Pressing against the screen can
cause distortion or other damage. The images may become unclear or the LCD
may be damaged.
1. AV1/AV2/VGA
4. Decrease brightness, contrast, color, volume, etc.
5. Increase brightness, contrast, color, volume, etc.
2. Menu (Up/Down/Left/Right)
3. Power: ON/OFF
Do not use this product in temperatures lower than -10ºC or higher than 60ºC.
4
5
Lynx LCD Monitor User Manual
Lynx LCD Monitor User Manual
REMOTE CONTROL OPERATIONS
Battery Installation
LCD REMOTE
•
•
•
Press down the card bolt and pull out the battery card
Place battery in card with anode (+) side upward
Place battery card back in original place
1
VIDEO
SELECT
1. Power
2
3
4
2. AV1/AV2/VGA
MENU
5
6
3. Function Decrease
4. Reset
MODE
SELECT
5. Function Increase
6. Menu (Up/Down/Left/Right)
Back of remote controller
Battery Slot
Battery
Card bolt
M-Lynx-10W Specifications
Type:
TFT LCD Digital Panel
10-inch
BATTERY REPLACEMENT
Screen size:
Under normal operating conditions, the battery will have a 1-year life (shorter,
depending on the conditions). Low battery power can result in a narrower working
range, so always make sure your remote has fresh batteries.
Definition:
1024 (h) x RGB x 600 (v)
Computer Resolution:
System:
800 x 600 or 1024 x 768 (60Hz)
Lithium Batteries
NTSC/PAL
Always keep the battery out of the reach of children. Clean the batteries with a dry
cloth to ensure best performance. When installing the batteries, make sure that
the polarity is correct. Do not use a metal clamp to remove or clip the battery as a
short circuit could result.
Nominal Voltage:
Power Consumption:
Control:
12V
5W MAX
Front panel button/Remote control
Note: The battery can explode if improperly handled. Do not throw battery in trash
or fire. Always recycle battery properly.
Operating Environment: -10ºC - +60ºC
Dimensions:
9.7” x 6.5” x .75”
7
6
|