Marantz DVD Recorder CDR310 User Manual

Model CDR310 User Guide

CD Recorder

CLASS 1 LASER PRODUCT

LUOKAN LASERLAITE

KLASS 1 LASERAPPARAT

IMPORTANT SAFETY

INSTRUCTIONS

READ BEFORE OPERATING EQUIPMENT

This product was designed and manufactured to meet strict quality

11. Only use attachments/accessories specified by the

and safety standards. There are, however, some installation and

operation precautions which you should be particularly aware of.

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified

by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

13. Unplug this apparatus during lightning storms or when unused

for long periods of time.

4. Follow all instructions.

14. Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacture’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

Additional Safety Information!

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has

•

This product should not be placed in a built-in installation such

as a bookcase or rack unless proper ventilation is provided or

the manufacturer’s instructions have been adhered to.

two blades with one wider than the other. A

grounding type plug has two blades and a

third grounding prong. The wide blade or the

third prong are provided for your safety. If the

provided plug does not fit into your outlet,

Apparatus shall not be exposed to dripping or splashing and

that no objects filled with liquids, such as vases, shall be

placed on the apparatus.

consult an electrician for replacement of the obsolete outlet.

The AC adaptor shall be installed near the Socket-Outlet and

shall be easily accessible.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

NOTE TO CATV SYSTEM INSTALLER:

This reminder is provided to call the CATV (Cable-TV) system installer's attention to Article 820-40 of the NEC, which provides guidelines for

proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the

point of cable entry as practical.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

NOTE:

Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user's authority to operate the

equipment.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B est conforme á la norme NMB-003 du Canada.

CE marking (only EU version)

English

This product is in conformity with the EMC directive and low-voltage directive.

Français

Cet appareil est conforme á la directive EMC et á la de directive sur les basses tensions.

Deutsch

Dieses Gerät entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte.

Nederlands

Dit apparaat voldoet aan de EMC-richtlijnene en de richtlijnen voor apparatuur met laag voltage.

Italiano

Quest' unitá è conforme alle direttive EMC ed alla direttiva sulle basse tensioni.

Português

Esta unidade está em conformidade com as directivas EMC e as directivas de baixa voltagem.

Español

Esta unidad estáde acuerdo con las normas EMC y las relacionadas con baja tensión.

Svenska

Produkten är tillverkad i enlighet med EMC-direktivet och direktivet för lågspänningsutrustning.

Equipment mains working system

This product complies with household power and safety requirements in your area.

SI DICHIARA CHE L'APPARECCHIO SINTO-AMPLIFACATORE SR-39

RISPONDE ALLE PRESCRIZIONI DELL'ART. 2 COMMA 1 DEL D.M. 28

AGOSTO 1995 N° 548.

FATTO A EINDHOVEN, IL 1/1/1997.

MARANTZ EUROPE B.V.

5600 EINDHOVEN

THE NETHERLANDS

"Este aparato lleva elementos antiparasitarios necesarios para cumplir

con los limites que se establecen en el Anexo V del Reglamento sobre

Pertubaciones Radioelectricas e Interferencias aprobado en el Real

Decreto 138/1989. (B.O.E. de 9 Febrero 1989)."

Table of Contents

3. AllMkErase (How to erase all EDL marks)

Package contents ......................... 3

Introduction .................................. 4

4. Format (How to format a CF card) ...... 28

Features .................................................... 4

Virtual Track and Copy Segment 29

Virtual Track .............................................. 29

Copy Segment ......................................... 29

Virtual Track Edit Mode ............................ 29

Preparation ................................... 6

Installing the carry strap ........................... 6

Installing batteries .................................... 6

Creating a Virtual Track ..............30

Controls and Connections .......... 7

Top side ..................................................... 7

Front side ................................................ 12

Left / Right side ....................................... 13

Rear side ................................................. 14

Display ..................................................... 15

Using Copy Segment to

create a new file ..........................31

Entering Virtual Playback mode 32

Virtual Track EDIT mode .............33

Basic operation .......................... 16

Copy SEG?

[How to convert a Virtual Track to a new file] 33

CF cards ...................................... 17

To insert a CF card .................................. 17

To eject a CF card ................................... 17

CF card security ...................................... 18

CF card Format ....................................... 18

Copy SEG A?

[How to convert all Virtual Tracks to new files]

VT Erase?

[How to erase a Virtual Track] .................. 34

AVT Erase?

Recording ................................... 19

Connection Diagram ............................... 19

Recording Procedure .............................. 19

Audio input for recording ........................ 20

Recording Format parameters ................ 21

Recording time chart ............................... 21

Recording Level Control .......................... 22

Microphone Attenuator ............................ 22

Pre Record .............................................. 22

Silent Skip (Automatic Pause Recording) 22

Add a Track manually .............................. 22

Add a Track automatically ....................... 23

[How to erase all Virtual Tracks] ............... 35

USB mode ................................... 36

Computer compatible .............................. 36

How to connect via the USB port ............ 36

Diagram of file structure .......................... 37

Machine ID .............................................. 37

Additional Functions ................. 38

Battery ..................................................... 38

Auto power off ......................................... 38

Beep Alarm .............................................. 38

Key lock ................................................... 39

Set Date and Time .................................. 39

LED level meter ....................................... 39

Phantom Power ....................................... 39

Display ..................................................... 40

Playback ...................................... 23

Connection Diagram ............................... 23

Playback Procedure ................................ 24

Track Access ........................................... 24

Search ..................................................... 24

Audible Search ........................................ 25

Audio output for playback ....................... 25

Preset Setup ............................... 41

Table of Preset defaults (USA) ................ 42

Table of Preset defaults (Europe) ........... 43

EDL Mark ..................................... 25

Add an EDL mark manually .................... 25

Search the EDL mark .............................. 25

Add an EDL mark automatically .............. 26

Troubleshooting ......................... 55

Error Message ............................ 57

Specifications ............................. 58

Edit ............................................... 26

LIMITED WARRANTY - USA .................. 59

1. Trk Erase (How to erase tracks) ......... 27

2. TrkMkErase (How to erase

all EDL marks within one track) ....... 27

●

Recording level and LR balance adjustment ( XX)

• Automatic recording level control (ALC)

• Manual control

☞

Introduction

Thank you for purchasing this CDR310 CD Recorder.

Before using the CD recorder, make sure that you read

through this instruction manual carefully to fully understand

the device’s functions and how to operate them. We hope

that you will continue to enjoy using the recorder for a very

long time. After reading this manual, please keep it in a safe,

easy to reach place for future reference.

You can record and playback audio in stereo (2 channel)

or monaural (1 channel).

●

You can play back CD-DA and Data CD (MP3, AIF, WAV).

The following sound outputs are available.

• Internal speakers

• Headphones connected to the headphone (PHONES)

Features

jack

●

You can record audio from an external microphone onto

the internal HD (Hard Disk), and then burn the audio onto

a CD-R.

• Amp or other analog audio devices connected to the

LINE OUT jack.

• Digital output

●

Audio input

●

2 types of power supply source

• Use the provided AC adaptor.

• Use alkaline batteries, the optional Nickel-Cadmium

battery (RB1100), or the optional Nickel-Metal Hydride

battery (RB1650).

• Condenser microphone or dynamic microphone (XLR

balanced input) connected to the MIC IN jack

• Internal microphone

• Line level audio source connected to the LINE IN jack

• Digital input (Coaxial input)

• Phantom power supply

• L/R independent attenuator for external microphone

input or internal microphone input

●

4 different types of recording format

(MP3, WAVE, CD-DA, AIFF)

• Compressed sound recording uses MPEG1 Layer III

(MP3) monaural and stereo recording.

• MP3 are compressed to 128kbps (stereo) or 64kbps

(monaural).

• Non-compressed sound recording uses 16-bit linear

pulse code modulation (PCM).

●

Simple recording

• You can start simple recording to the HD just by

pressing the REC button once. The HD capacity is

1.5GB. (Approx. 2 hours in PCM recording)

●

You can create an extended play recorded CD (maximum

25 hours 29 minutes on a 700MB CD-R disc in MP3 mono

format).

●

Simple CD creation

• You can burn data recorded on the HD onto a CD-R just

by pressing the MAKE CD button.

●

Convenient special recording functions

• Pre-code cache

(

☞

XX)

• Background recording ( XX)

☞

• Silent skip

• Auto track

• Manual track

(

☞

(

☞

(

☞

XX)

Package contents

• CDR310

• AC power pack

• Power cord

• Battery holder (AA type)

• User Guide

• Customer Registration Document

Quick Start Guide

Before using the CDR310, please read through the following section which explains the basic flow of operation.

1. Setup the power supply ( P.XX)

☞

• Use either the provided AC adaptor or batteries.

• You can use any one of the 3 types of batteries:

Alkaline, optional Nickel-Cadmium, or optional Nickel-

Metal Hydride.

POWER

OFF ON

• Please make sure batteries are fully charged.

2. Connect an external microphone and turn the power ON. ( P.XX)

☞

• Connect the external microphone to the MIC IN jack. (

☞

P.XX)

• Slide the power switch to the ON side. ( P.XX)

☞

MIC IN

3. Record ( P.XX)

☞

• Press the REC button, and recording starts.

• Adjust the recording level/LR balance. ( P.XX)

☞

• Detailed settings for recording. ( P.XX)

☞

• Press the STOP button, and recording stops.

4. Burn a CD ( P.XX)

☞

• Press the MAKE CD button to burn to a CD-R.

• When the CD burning process has completed, the CD-R is

automatically ejected.

• To continue to burn to a different CD-R, insert a new

CD-R.

• If the CD creation is ended without burning onto another

CD-R, all of the HD data is deleted.

ADDITIONAL INFORMATION

About Discs

The glossy side shining like a rainbow is the front side of the

disc, and the side on which the label is printed is the back.

Unlike conventional turntables for playing analog discs,

the unit reads the information recorded on the disc from

underneath without contacting it using a beam of laser

light. Therefore, the performance of a compact disc will not

degrade like conventional analog records.

Playable discs

CD-R

Handle discs carefully so as not to damage or scratch

the front side.

To protect the disc, avoid placing it in the following

locations:

CD-RW

•

In direct sunlight or near a source of heat like a heater.

In a place which is damp or dirty.

In a place which could be exposed to rain, such as near a

window.

Finalized CD-R and CD-RW discs recorded in the CD-DA

format, MP3 format or Video-CD format can be played with

the unit.

Always keep the disc surface clean.

When cleaning the disc surface, always be sure to use a

special compact disc cleaner and wipe as shown below.

•

Finalize is the process to make a CD-R/CD-RW playable

for players (not recorders)

Some discs may not be able to be played depending on

condition of the discs and recording software.

Single CDs (8cm) cannot be used.

•

Do not use conventional record cleaner for analog records,

as this will adversely affect the disc surface.

Store discs properly by placing them in their disc cases.

Do not attach a piece of paper or sticker on the label side

of disc. When a disc has a piece of plastic tape or rental

DVD/CD label with paste protruded from the edge or when

a disc has a trace of such a sticky object, do not attempt

to play the disc. If such a disc is played on the DVD player,

impossibility of taking out the disc or other malfunction

may result.

•

Do not use a disc with a special shape.

Do not attempt to play a disc with a special shape such

as a heart-shaped disc or octagonal disc. Otherwise the

equipment malfunction may result.

Names and Functions

Top side

q Power switch

• Track selection

Slide this switch to switch the power on/off.

You can select the track you wish to play back by rotating

the JOG while playback is paused, stopped, or during

playback. After selecting the track that you wish to play

back, press the JOG or PLAY/PAUSE button to play back

w DISPLAY button

Press this button to switch the contents of the display.

The displayed information is different when the recorder is

stopped, recording, and playing back. ( P.XX)

☞

the selected track. ( P.XX)

☞

• MENU mode

e LIGHT button

You can select the MENU items by rotating the JOG in

the MENU mode. Press the JOG after selecting an item to

choose that item. Press the CANCEL button to cancel the

selection.

Press this button to light the display light for 3 seconds.

Hold this button down for 1 second to keep the display

light on. Press this button once again to turn the display

light off.

u Internal speakers

r MAKE CD button

The audio signal being played back is output to the

internal speakers. If headphones are connected to the

headphone (PHONES) jack, sound is not output from

the internal speakers. Adjust the speaker volume using

LEVEL volume.

You can burn the recorded data to CD-R by pressing this

button when the recorder is stopped. ( P.XX)

☞

t HD/CD button

Press this button when the recorder is stopped to switch

between the HD recording/playback mode and CD

playback mode.

i MIC (Internal microphone)

o CHARGE Indicator

y JOG/ENTER button

• REC LEVEL control

This LED flashes while the optional rechargeable

batteries are being recharged.

You can adjust the recording level by rotating the JOG

while the recording is paused, or during recording.

You can also adjust the recording level left and right (L/R)

balance by holding down the MENU button and rotating

The LED goes out when recharging has finished.

! Display ( P.XX)

☞

the JOG. ( P.XX)

☞

! PLAY/PAUSE button

Press this button when the recorder is stopped to start

playback.

Press this button during playback to pause playback.

Also, if this button is pressed when playback is paused,

playback restarts.

! STOP button

Press this button during recording to stop the recording

and save the recorded track (file).

Press this button during playback to stop playback. If you

press the PLAY/PAUSE button after pressing the STOP

button, the stopped track starts playback again from the

beginning of the track.

! REC PAUSE button

Press this button when the recorder is stopped to pause

recording. You can adjust the recording level before

recording in this state.

Press this button during recording to pause recording.

The REC indicator flashes while recording is paused.

! MENU/STORE button

! REC button

Press this button when the recorder is stopped to start

recording.

Also, press this button when recording is paused to start

recording again.

If “Manual Trk” is set to ON in the menu item labeled

“preset menu”, pressing this button during recording

saves the track currently being recorded, and starts

recording as a new track.

• MENU

Press this button when the recorder is stopped to switch

to the Menu mode. Turn the JOG to select the item that

you wish to set from the various menu items. ( P.XX)

☞

• STORE

Press this button when you want to enter changes in the

menu items, and when you want to write to the recorder.

Press the STOP button to stop recording.

• REC BALANCE

! REC Indicator

You can adjust the recording level L/R balance by holding

down this button and rotating the JOG.

Remains lit while recording and flashes while recording is

paused.

! F.REV (5) button

@ UNDO button

Press this button when the recorder is stopped to pause

playback. Continue to press and hold this button to search

tracks in reverse direction from the first track.

Press this button after stopping recording to delete the

recorded track. ( P.XX)

☞

Press and hold this button during playback to search

tracks in reverse direction at 2 times speed playback.

Release the button to return to normal playback.

Press and hold this button when playback is paused to

search tracks in reverse direction.

! F.FWD (6) button

Press this button when the recorder is stopped to pause

playback. Continue to press and hold this button to search

tracks in the forward direction from the first track.

Press and hold this button during playback to search

tracks in the forward direction at 2 times speed playback.

Release the button to return to normal playback.

Press and hold this button when playback is paused to

search in the forward direction.

! CANCEL button

Press this button in the MENU mode to cancel the menu

contents being set, and to return to the stopped status.

Front side

z CD slot

b Headphone (PHONES) jack

Insert the stereo headphones plug here.

x EJECT button

n LEVEL volume

Press this button to eject the CD that is inside the CD slot.

Turn this knob to adjust the internal speaker volume or

volume output from the headphone jack.

c KEYLOCK switch

Set this switch ON to set to the key-lock status. All of the

operating buttons and switches are locked, except for the

LIGHT button.

Notes

When recording with the internal microphone, switch the

SPEAKER switch OFF to avoid feedback between the

internal microphone and speakers.

v SPEAKER switch

Set this switch to OFF to mute the output from the internal

speakers.

Rear side

m Battery case

Open the battery cover case, and insert the supplied

battery holder (with alkaline batteries inserted), or the

commercially available Nickel-Cadmium battery or Nickel-

Metal Hydride battery.

Right side

E F G

A MIC IN jacks (L/R) (XLR balanced input)

E LINE IN jacks (L/R)

Insert an external microphone plug.

For monaural recording, plug into either the L side or R

side jack.

Insert RCA audio cable plugs connected to an external

audio device into these jacks to input the signals output

from the external device into the recorder.

B DC IN jack

F LINE OUT jacks (L/R)

Insert the provided AC adaptor plug.

The power supply is DC15V, 2.3A.

If the AC adaptor plug is inserted while using the recorder

on battery power, the recorder will automatically switch to

adaptor power. Also, if the AC adaptor plug is removed,

the recorder will automatically switch to battery power.

Insert RCA audio cable plugs connected to an external

audio device into these jacks to output audio signals to an

external device (amp, etc.).

G DIGITAL IN/OUT

• IN

Connects to the digital signal output terminal (Coaxial) of

a digital device (DVD, CD, MD, etc.).

C REMOTE 1 jack

Insert a contact closure plug similar to the one shown

below into this 2.5mm mini jack.

• OUT

Connects to the digital signal input terminal (Coaxial) of a

digital recording device (CD recorder, MD recorder, etc.).

Switch

2.5mm mini jack

You can remotely control playback/recording of the

recorder by opening and closing the switch contact. (

P.XX)

☞

D REMOTE 2 jack

Connect microphone remote RC600PMD (sold

separately) to this jack. There is a recording indicator

lamp on the RC600PMD.

Display

s d f g hj k l ¡

¡ ¡

a Upper character display section

l M.TRACK icon

Displays the remaining time, etc.

Lights when “ManualTR” is set to ON in the preset menu.

s TOTAL/TRACK/TIME/REC/REMAIN icon

¡ A.TRACK icon

The following types of details are displayed in the upper

character display section.

Lights when “Auto TRK” is set to ON in the preset menu.

¡ S.SKIP icon

Explanation of display

Lit display

Lights when “SilentSkip” is set to ON or TRK in the preset

menu.

in upper character display section

Lights when the remaining recordable

time is being displayed.

REC REMAIN TIME

¡ TRACK icon

Lights when the current time or the

recording time is being displayed.

TIME

Lights when the track number is displayed in the lower

character display section.

Lights when the playback elapsed time

TRACK TIME

or the recording elapsed time is being

displayed.

¡ Lower character display section

Lights when the recording time of the

track is being displayed.

Displays the track number, channel, etc.

REC TIME

¡ Input signal (DIG/MIC/INT/LINE) icon

Lights when the remaining playback time

is being displayed.

Lights when the total time for all tracks is

being displayed.

TRACK REMAIN TIME

TOTAL TRACK TIME

Shows the type of input signal when recording.

Lit display

DIG

Type of input signal

Lights when “Input” is set to Dig-In in the preset

menu.

d kbps icon

Lights when “Input” is set to MIC in the preset

menu.

Lights when the bit rate for the recording format is being

displayed in the upper character display section.

MIC

Lights when “Input” is set to Int. MIC in the

preset menu.

Lights when “Input” is set to Line in the preset

menu.

INT MIC

LINE

f ALC icon

Lights when “REC Level” is set to ALC in the preset menu.

g PHANTOM icon

¡ Recording/Playback/Pause mark

Lights when “Phantom” is set to ON in the preset menu.

Shows the operating status of the recorder.

h kHz icon

Lit display

Operating status

Lights when the sampling frequency for the recording

format is being displayed in the upper character display

section.

Playback

2 ;

Playback paused

Recording

0 2

Recording paused

(Recording standby status)

0 2 ;

j AM/PM icon

When the clock setting is set to 12-hour display, the current

time or recording time is displayed in the AM/PM format.

¡ Battery remaining indicator

Displays the remaining battery power.

k Level meter icon

¡ HD/CD icon

Displays the recording levels in the left and right channels

during recording.

Lights when the recorder is in the HD mode or CD mode.

Displays the playback levels in the left and right channels

during playback.

The level meter display dots have a peak hold function

that holds for a fixed amount of time. (Self reset)

Using batteries

If you wish to run the recorder on battery power, follow the

procedure below to install batteries into the provided battery

holder, and insert the holder into the recorder.

Preparations Before Use

AC adaptor connection

When using the recorder with the provided AC adaptor, follow

the procedure below to connect the AC adaptor.

If you wish to use batteries, please refer to the [Using

batteries] section. ( P.XX)

☞

The following types of battery can be used.

●

Alkaline batteries

●

Optional Nickel-Cadmium battery (option: parts number

RB1100)

●

Optional Nickel-Metal Hydride battery (option: parts

Notes

number RB1650)

Only use the AC adaptor that is provided with the recorder.

Running the recorder on DC power without using the

provided AC adaptor will cause damage to the recorder.

(Guide to battery lifespan)

When alkaline batteries (1450mAh type) are used

HD Recording: about 4 hours

1 Connect the plug of AC power pack into the DC IN jack on

Notes

the recorder.

●

When running the recorder on batteries, always set the

battery type in the preset menu to the correct setting for

the batteries used. ( P.XX)

☞

2 Connect the Power cord to a regular household plug

socket.

1 Insert 8 batteries into the battery holder correctly as

shown in the diagram below, while paying attention to the

polarity displays (+: plus, and -: minus).

POWER

OFF ON

Power cord

DC IN jack

Battery holder

AC power pack

Notes

2 Remove the battery case cover from the rear side of the

recorder.

If a optional rechargeable battery is inside the recorder, the

battery will be recharged in this state.

Battery case cover

Installing an optional Ni-Cd or Ni-MH battery

3 Insert the battery holder into the battery case of the

recorder correctly as shown in the diagram below, while

paying attention to the polarity displays (+: plus, and -:

minus) on the case.

Optional battery

tab

Battery holder

tab

ribbon

Install the battery with tab as shown and over the ribbon for

easy battery removal.

When changing battery type, be sure you change the Battery

type menu setting for optimal battery performance.

4 Re-attach the removed battery case cover.

Notes

Charging the optional Ni-Cd battery

• Load the Ni-Cd battery correctly in the battery

●

When using the optional rechargeable batteries for the first

time, fully charge the batteries Connect the provided AC

adaptor to the recorder to recharge the batteries.

compartment.

• Connect the AC power pack and AC adaptor into power

supply.

●

If the batteries run out during the HD recording, recording

automatically stops and the file information is updated

before the recorder shuts down.

• Select Ni-Cd in the battery type menu. ( P.XX)

☞

• Power the CDR310 on, then off for the charging cycle to

begin.

• The CDR310 must be off during battery charging.

●

When burning data from the HD to a CD-R, the CD

burning process will not start if there is not enough battery

power remaining. Furthermore, if the batteries run out

while burning to the CD-R, recording will stop and the

recorder will shut down. If this happens, the CD burning

process may not complete correctly.

While charging (about 3 hours), the CHARGE indicator will be

lit and steady.

When the Ni-Cd battery charge cycle is complete, the

CHARGE indicator will be off.

Safety cautions on handling batteries

Always follow the points below when using batteries to avoid

electrolyte leakage, overheating, fire, rupturing, ingestion, etc.

●

Electrolyte leakage or corrosion may occur if batteries

are kept inside the recorder for prolonged periods of

time. If the recorder is not to be used for a prolonged

period, remove the batteries to prevent electrolyte

leakage.

●

Make sure that the + and – markings on the batteries

are aligned with the corresponding markings in the

battery case and the battery holder.

Do not recharge, heat, or disassemble batteries. Do not

●

throw dry cell batteries onto a fire.

Do not insert old or exhausted batteries into the

●

recorder.

●

Do not mix the type of battery, and do not use both old

and new batteries together.

If the recorder does not operate correctly, replace the old

●

batteries with new ones.

If electrolyte has leaked, thoroughly wipe the inside of

●

the battery holder, and then insert new batteries.

Battery type settings

Set the battery type for the recorder to match the type of

batteries you are using.

Basic Operations

Power on/off

1 Slide the power switch to the ON side to switch the

< Default value > Alkaline

power ON.

1 While the recorder is stopped, press the MENU/STORE

Notes

button.

The factory-preset settings are set to record sound using

the external microphone input. Refer to “Menu Settings”

for details on the default settings of the various menus. (

P.XX)

☞

2 Turn the JOG to select “Batt Type” and press the JOG.

• At this time, the display shows “Loading”.

The recorder’s BOOT process starts.

3 Turn the JOG to select the type of battery, and press the

JOG.

• The recorder stops when the BOOT process completes.

2 Slide the power switch to the OFF side to switch the

power OFF.

Display

Alkaline

Battery type

Alkaline battery

Optional Nickel-Cadmium

battery

NiCd

Optional Nickel-Metal

Hydride battery

NiMH

4 Press the MENU/STORE button to register the settings.

Battery remaining indicator

The recorder operates using commercially available AA size

alkaline batteries, the optional Nickel-Cadmium battery, or the

optional Nickel-Metal Hydride battery. During operation, the

battery remaining indicator is as follows.

Remaining

Display explanation

indicator

Nothing is displayed when the AC adaptor is being

No display

used. The adaptor power supply is valid.

There is still ample battery power remaining.

The amount of battery power remaining has

decreased to approx. half.

Only a small amount of battery power remaining.

There is not enough battery power remaining to

record or playback. Either replace the batteries with

new ones, or recharge the rechargeable batteries.

There is almost no remaining battery power.

If the “Beep” setting in the menu are set to ON, the

beep sound will be heard.

If you continue recording while this indicator is

flashing, recording/playback will stop, and the

recorder will shut down.

Flashing

Notes

If the battery type is not set correctly to match the type of

battery being used, the battery remaining display may not

be displayed correctly.

Setting the clock

Set the current time (year, month, date, hour, minute).

5 Turn the JOG to select [Year (2006 to 2099)], and press

the JOG.

Notes

The setting order is different depending on the “DateForm”

settings in the menu. Check the “Date form settings”

setting. ( P.XX)

☞

DateForm

Setting order

M (Month) / D (Date) / Y (Year) Month/Date/Year/Hour/Minute

D (Date) / M (Month) / Y (Year) Date/Month/Year/Hour/Minute

Y (Year) / M (Month) / D (Date) Year/Month/Date/Hour/Minute

6 Turn the JOG to select [Time], and press the JOG.

For 24 hour display : 0 ~ 23

For 12 hour display : 0am ~ 11pm

< When DateForm: M/D/Y >

1 While the recorder is stopped, press the MENU/STORE

button.

7 Turn the JOG to select [Minute (00 to 59)], and press the

JOG.

2 Turn the JOG to select “Date/time” and press the JOG.

8 Press the MENU/STORE button to register the settings.

3 Turn the JOG to select [Month (Jan to Dec)], and press

the JOG.

4 Turn the JOG to select [Date (01 to 31)], and press the

JOG.

Date form settings

Time form settings

There are 3 types of date form. You can set the form to your

own preference.

There are 2 types of time form. You can set the form to your

own preference.

Form type

M/D/Y

Form subjects

Month/Date/Year

Date/Month/Year

Year/Month/Date

Form example

Jan 10 2006

10 Jan 2006

2006 Jan 10

Form type

12H

Form subjects

AM/PM display

24 hour display

Form example

01 : 00 : 00 pm

13 : 00 : 00

D/M/Y

24H

Y/M/D

< Default value > 12H

< Default value > M/D/Y

1 While the recorder is stopped, press the MENU/STORE

button.

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Time Form” and press the JOG.

2 Turn the JOG to select “Date Form” and press the JOG.

3 Turn the JOG to select the type of time form, and press

the JOG.

3 Turn the JOG to select the type of date form, and press

the JOG.

4 Press the MENU/STORE button to register the settings.

Menu Settings

The recorder uses 8 menus to set the various functions.

There is a menu for basic settings such as time (display method), alarm, automatic power off, and battery type, and a menu for

formatting the internal HD. These menus are displayed by pressing the MENU/STORE button once to enter the menu mode.

You can also perform detailed settings for the recording and playback conditions, and register up to 3 of these settings in the

preset menu. To enter this preset menu, select “PRESET” using the JOG, then specify the preset number.

Refer to “Preset Menu” for details on preset items. ( P.XX)

☞

Menu mode

MENU/STORE Button

First level

Second level

Preset

Input

Date/Time

RecFormat

CD Split

Default

FORMAT HD

The composition of these menu contents is explained below.

P.XX)

Menu explanation

Settings

Default settings

Preset-1

3 settings can be registered. Select the

preset number, and set the various items.

Preset-1, 2, 3

Preset (

☞

2006−2099

JAN − DEC

1 − 31

2006

JAN

Sets the clock (current date and time).

Date/Time (

P.XX)

☞

AM/PM 0:00 − 11:59, (0:00 − 23:59)

AM0:00 (0:00)

Selects the type of date form.

Selects the type of time form.

Sets the alarm on/off.

M (Month) / D (Date) / Y (Year), D/M/Y, Y/M/D,

M/D/Y

12H

Date Form (

P.XX)

☞

12H, 24H

On/Off

Time Form (

☞

Beep (

P.XX)

☞

On/Off

Time : 5/10/15/30 min

Off

15 min

Sets the automatic power off setting.

A.PowOff (

P.XX)

☞

You can select the type of battery.

Formats the HD.

Alkaline, NiCd, NiMH

(Execute)

Alkaline

−

Batt_Type (

P.XX)

☞

HD Format (

☞

Preset menu

You can register up to 3 detailed setting on the recorder for such settings as recording input, recording conditions, recording

format, playback mode, remote control, etc. There are 17 setting items in the preset menu, and 3 presets can be set with the

desired conditions.

The contents of the preset menu are explained below.

Preset1 : High quality PCM recording

Preset2 : Meeting recording (monaural)

Preset3 : MP3 music recording

Default settings

Preset menu

Input ( P.xx)

Menu explanation

Selects the input source.

Settings

Preset1

MIC

Preset2

MIC

Preset3

MIC

MIC, Line, Int. MIC, Dig-In

☞

Stereo, Mono

CD-DA, WAVE, MP3, AIFF

Stereo

CD-DA

Mono

MP3

Stereo

MP3

Sets the recording format.

RecFormat (

P.xx)

☞

When burning HD data to CD-R, this sets

the saving procedure for the final track

when all of the contents will not fit onto one

CD-R.

On/Off

CD Split (

P.xx)

☞

Sets PreRecord.

Off/1−10 sec (1 sec steps)

Off

4 sec

PreRecord (

Rec Level (

P.xx)

☞

Sets the recording level operating method. Manual/ALC

Manual

P.xx)

☞

External microphone

Sets the attenuator function for the left On/Off

channel side.

Off

MIC-ATT-L (

P.xx)

☞

External microphone

Sets the attenuator function for the right On/Off

channel side.

MIC-ATT-R (

P.xx)

☞

Sets the attenuator function for the internal

microphone.

On/Off

Off

IntMicATT (

Phantom (

☞

Sets the Phantom power supply when a

On/Off

P.xx)

☞

condenser microphone is connected.

Sets background recording.

Sets Manual Track.

On/Off

Off

BkGrndRec (

P.xx)

☞

ManualTR (

P.xx)

☞

On/Off

Off

5 min

Off

5 min

Time : 1/5/10/15/30 min,

1/2/6/8/12/24 Hrs,

640/700 MB CD

Sets Auto Track.

Sets Silent Skip.

Auto TRK (

P.xx)

☞

On/Off

Off

3 sec

-40dB

Off

3 sec

-40dB

Off

3 sec

-40dB

Time : 1−5 sec (1 sec steps)

Level: -60− -20dB

(5dB steps)

SilentSkp (

P.xx)

☞

Normal, Repeat All,

Repeat TRK, Single

Sets the playback mode.

Sets the Stop Monitor.

Normal

Off

Normal

Off

Normal

Off

Play Mode (

P.xx)

☞

On/Off

StopMonit (

☞

Sets the operating mode controlled by the * StartPause, StartPauTR,

Manual TRK StartPauTR StartPause

Remote (

P.xx)

☞

opening and closing of a switch contact.

Manual TRK

Returns the settings of the selected preset

number only to the default values.

(Execute)

---

Default (

P.xx)

☞

* StartPause : Start / stop

StartPauTR : Start / stop + track increment

Manual TRK : Manual track

Menu operation

The recorder uses menus to set various functions. (

4 Turn the JOG to select the menu settings, then press the

JOG to choose the selected settings.

☞

P.XX) You can alter the basic settings and use a wide range

of recording and playback functions by changing the menu

settings. The basic menu operations are explained in this

section.

Second level

Input

RecFormat

CD Split

1 While the recorder is stopped, press the MENU/STORE

PreRecord

button to enter the menu mode.

Menu mode

• Repeat the procedure above of rotating the JOG to

select settings and items, and pressing the JOG to

choose items and contents, to set each of the menu

items.

MENU/STORE Button

First level

Preset

Date/Time

Date Form

5 Finally, press the MENU/STORE button to register all of

the settings.

• The recorder enters the menu mode.

2 Turn the JOG to select a menu item.

Menu mode

MENU/STORE Button

First level

Preset

Date/Time

Date Form

3 Press the JOG to choose the selected menu item.

Menu mode

MENU/STORE Button

First level

Preset

Date/Time

Date Form

• The recorder enters the setting mode for the menu item.

2 Press the REC PAUSE button to pause recording.

• The recording mark flashes in the display while

recording is paused.

Recording to the HD

Schematics

REC PAUSE

• Press the REC button when recording is paused to start

recording again.

MIC IN

LINE

DIGITAL

3 Press the STOP button to stop recording.

• The recorded track (file) information is saved to the HD.

Basic operations for recording

• Press the PLAY button after this to play back the

recorded track from the start.

1 Press the REC button when the recorder is stopped to

start recording.

4 Press the STOP button once again to return to the

• During recording, the REC indicator lights and the

following contents are displayed on the display.

stopped status.

• Press the PLAY button after this to play back from the

first track.

Notes

●

The default preset settings for [Recording level control

settings] are set to “Manual”. For details on adjusting the

recording level/LR balance, please refer to [Recording

level control settings]. ( P.XX)

☞

●

When recording with the internal microphone, switch the

SPEAKER switch OFF to avoid feedback between the

internal microphone and speakers.

• Also, to start recording from the recording standby

status, press the REC PAUSE button while the recorder

is stopped to switch to recording standby status.

When in recording standby status, the REC indicator

flashes and the following contents are displayed on the

display.

REC PAUSE

Adjust the recording level/LR balance while in recording

standby. ( P.XX)

☞

After adjusting the recording level/LR balance, press the

REC button to start recording.

Erasing recordings

Formatting the HD

You can erase data (tracks) recorded to the HD after stopping

recording.

Formats all of the tracks recorded onto the HD.

Notes

1 After stopping recording, press the UNDO button to

switch to the erase mode of the recorded track.

• “REC UNDO?” is displayed for 3 seconds.

If the HD is formatted, all contents of the HD are erased.

Before formatting, re-check the contents of the HD.

1 While the recorder is stopped, press the MENU/STORE

button.

2 Press the UNDO button again while “REC UNDO?” is

being displayed.

• The recorded track is erased, and “Completed” is

displayed for 3 seconds.

2 Turn the JOG to select “Format HD” and press the JOG.

• A confirmation message to perform HD format is

displayed.

3 To format the HD, press the JOG.

• “Formatting” is displayed while the HD is being

formatted.

• After formatting has completed, “Completed” is

displayed for 1 second After that, the recorder returns to

the stopped status.

5 Turn the JOG to select the type of input source (“MIC”,

Detailed Settings for HD Recording

“Line”, “Int.Mic”, “Dig-In”), and press the JOG.

Input source settings

Set the input source (internal microphone, external

microphone, line input, digital input) for recording.

< Default value > Preset1 : MIC

Preset2 : MIC

Preset3 : MIC

Notes

6 Press the MENU/STORE button to register the settings.

If digital input is set, only the sampling frequency 44.1KHz

is available. Any other frequencies are displayed as

unlocked, and are not recorded.

1 While the recorder is stopped, press the MENU/STORE

button.

Notes

Depending on the combination of input source

and recording format (channel), the input signal

stereo / monaural settings are as follows.

For details on the recording format settings, please refer to

[Recording format settings]. ( P.XX)

☞

2 Turn the JOG to select “Preset” and press the JOG.

Recording format (channel)

Stereo

Mono

External microphone

L/R Stereo

L/R Mono Mix

Mono

Internal microphone Same source in L/R

LINE Input

L/R Stereo

L/R Mono Mix

DIGITAL input

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

4 Turn the JOG to select “Input” and press the JOG.

Recording format settings

Set the recording format (compression format and channel) for recording.

< Default value > Preset1 : Stereo/CD-DA

Preset2 : Mono/MP3

Preset3 : Stereo/MP3

Notes

The recording format can only be changed when there are no tracks saved on the HD. There is only one HD recording format

on the recorder. This cannot be changed if tracks are already recorded in a certain format. To change the recording format,

either burn the data to a CD-R, or format the HD. When data is burned to a CD-R, the data on the HD is erased. Stereo/

monaural can be changed.

[Recording format parameters]

The recorder can record in the following compression formats and channels.

• Compressed sound recording that uses MPEG Audio Layer III (MP3) in either monaural or stereo.

• Non-compressed sound recording that uses the 16-bit linear pulse code modulation used on a CD.

• Non-compressed sound recording that uses WAVE (Windows standard audio file format)

• Non-compressed sound recording that uses AIFF (the audio file format developed by Apple Computer, Inc.)

The format parameters that can be recorded are as shown below.

When the channel setting is Stereo

Recording format Sampling frequency

Bit rate

Extension

.mp3

.cda

Recordable time

055:55:24

MP3

CD-DA

WAVE

AIFF

44.1KHz

128Kbps

005:04:21

.wav

005:04:21

.aif

005:04:21

When the channel setting is Mono

Recording format Sampling frequency

Bit rate

64Kbps

Extension

.mp3

.cda

Recordable time

111:50:49

MP3

CD-DA

WAVE

AIFF

44.1KHz

010:08:42

.wav

010:08:42

.aif

010:08:42

When burning from the HD to CD, the CD-R Format is decided by the recording format as shown below.

Recording format

MP3

CD Format

Data Disc

CD-DA Disc

Data Disc

CD-DA

WAVE

AIFF

Set the recording format (compression format and channel)

using the procedure shown below.

6 Turn the JOG to select the channel (“Stereo”, “Mono”)

and press the JOG.

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Preset” and press the JOG.

7 Press the MENU/STORE button to register the settings.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

4 Turn the JOG to select “RecFormat” and press the JOG.

5 Turn the JOG to select the compression format (“MP3”,

“CD-DA”, “WAVE”, “AIFF”), and press the JOG.

Recording level control settings

Set the recording level control and operating method (ALC,

Manual) for recording.

4 Turn the JOG to select “RecLevel” and press the JOG.

• Automatic level control (ALC)

If the recording level control or operating method is set to

ALC, the recording level for external microphone input or

internal microphone input is automatically set.

When ALC is set, the ALC icon lights in the display.

Notes

5 Turn the JOG to select the operating method of the

ALC becomes invalid for line input or digital input

recording. Even if the ALC is set, control switches to

manual control.

recording level (“ALC”, “Manual”) and press the JOG.

• Manual control (Manual)

If the recording level control or operating method is set

to Manual, turn the JOG to set the recording level when

recording is paused or during recording.

Also, the LR balance can be set by holding down the

MENU button and rotating the JOG during recording.

6 Press the MENU/STORE button to register the settings.

< Default value > Preset1 : Manual

Preset2 : Manual

Preset3 : Manual

While the recorder is stopped, press the MENU/STORE button.

2 Turn the JOG to select “Preset” and press the JOG.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

[Operations when manual control is set]

When the recording level control or operating method is

set to Manual, use the JOG as shown below to set the

recording level.

• Recording level settings

Turn the JOG while recording is paused or during

recording, and the manual level control screen is

displayed.

Turn the JOG to set the level.

(The level can be changed from +10dB to -∞dB)

• LR balance settings

Hold down the MENU button and turn the JOG while

recording is paused or during recording, and the LR

balance control screen is displayed.

Turn the JOG to set the LR balance.

The LR balance can be changed to 0dB to -18dB on the

left, or 0dB to -18dB on the right.

If the above-mentioned recording level and LR balance

are left without operation for 3 seconds, the recorder

returns to the previous display mode.

Microphone attenuator

Set the attenuator function for external microphone input and

internal microphone input.

4 Turn the JOG to select the microphone attenuator item

(“MIC-ATT-L”, “MIC-ATT-R”, “IntMicATT”) that you want to

set in the preset menu, and press the JOG.

For external microphone input, set this function when using

microphones directly that have different sensitivity levels. The

attenuator function for the external microphone can be set for

the L/R sides respectively.

For internal microphone input, set this function when the

sensitivity is too high.

• Attenuator OFF (0dB)

No microphone level attenuation.

Preset menu

MIC-ATT-L

MIC-ATT-R

IntMicATT

Menu contents

External microphone L Channel

External microphone R Channel

Internal microphone

• Attenuator ON (-20dB)

The input signal from either the microphone connected to

the MIC IN jack or the internal microphone is attenuated

by 20dB.

< Default value > Preset1 : Off

Preset2 : Off

5 5 Turn the JOG to select function On/Off, and press the

JOG.

Preset3 : Off

1 While the recorder is stopped, press the MENU/STORE

button.

6 Press the MENU/STORE button to register the settings.

2 Turn the JOG to select “Preset” and press the JOG.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

Phantom power settings

The recorder has DC+48V (P48) phantom power, and the

phantom power can be set On/Off.

5 Turn the JOG to select function On/Off, and press the

JOG.

Set to On when a condenser microphone that requires the

external power source is used.

When set to On, the “PHANTOM” icon lights in the display.

For details, please refer to the instruction manual that came

with your microphone.

Phantom power consumes battery power. Set this setting

to Off when using the internal microphone, a dynamic type

microphone, or other such microphone that does not use

phantom power.

6 Press the MENU/STORE button to register the settings.

< Default value > Preset1 : Off

Preset2 : Off

Preset3 : Off

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Preset” and press the JOG.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

4 Turn the JOG to select “Phantom” and press the JOG.

Prerecord

Set the PreRecord function.

5 Turn the JOG to select the temporary save time (1 to 10

seconds), and press the JOG.

When the PreRecord function is set to On, sounds from the

input source are always saved only for a set period of time

(1 to 10 seconds) in modes other than CD playback mode,

Make CD mode, during playback, or during playback pause.

When the recording is restarted, the audio data temporarily

saved in the recorder is written to the HD, then recording

continues from there.

This can be set to a maximum of 10 seconds, which prevents

missing the first part of a recording when recording is

suddenly started.

6 Press the MENU/STORE button to register the settings.

< Default value > Preset1 : Off

Preset2 : 4 sec

Preset3 : 4 sec

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Preset” and press the JOG.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

4 Turn the JOG to select “PreRecord” and press the JOG.

Background recording

Set background recording.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

When background recording is set to On, recording is

continued inside the recorder while recording is paused. This

can be used to recover data after pausing a recording, so that

nothing is missed even if important contents are lost while the

recording is paused.

When the REC button is pressed to restart recording from the

recording paused status, the display shows “Cont REC?” (Do

you continue the recording?) “Yes”.

4 Turn the JOG to select “BkGrndRec” and press the JOG.

Turn the JOG to select Yes/No, and press the JOG.

• When Yes is selected

The audio data recorded by background while the

recording was paused continues to be recorded.

• When No is selected

The data recorded by background is erased, and the

recording starts as a new track. The new track is created

from the point in which the track No is selected. At this

time, if prerecord is set, only the data for the prerecord

setting time remains.

5 Turn the JOG to select function On/Off, and press the

JOG.

Also, if the STOP button is pressed, the recording and this

function stops.

< Default value > Preset1 : Off

Preset2 : Off

Preset3 : Off

6 Press the MENU/STORE button to register the settings.

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Preset” and press the JOG.

Silent skip

Set the silent skip function.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

• Silent skip

The silent skip function automatically pauses the recording

if there is a period of no signal during recording. Recording

automatically starts again when an input signal is received.

This function cuts unnecessary sections (sections with

no sound) from within one track, and saves only the

necessary sections. The file size is smaller, search is

easier during playback, and the tracks are easier to listen

to.

4 Turn the JOG to select “SilentSkp” and press the JOG.

When silent skip is set, “S.SKIP” lights in the display, and

it flashes when the recording is paused while there is no

input signal.

• Silent skip/Track increment

Silent skip is processed within one track. However, if this

function is set, every time the input signal is received, a

new track is automatically created for the recording.

Notes

5 Turn the JOG, and select “On” to set silent skip, “T/ON” to

set silent skip/track increment, or “Off” if you do not wish

to set either. After making your selection, press the JOG.

• This function does not operate when [Background

recording] is set to On in the preset menu.

• When silent skip is set to ON, the prerecord function

operates for 2 seconds, irrespective of the prerecord

setting time.

• When silent skip is set to On, and the REC PAUSE button

is pressed while the recorder is paused due to there being

no signal, the recorder switches to regular recording pause

status. At this time, the S.SKIP icon flashes in the display.

T / ON

Off

Silent Skip

Silent Skip Track

Off

< Default value >

Preset1 : Off / Time : 3 sec / Level : -40dB

Preset2 : Off / Time : 3 sec / Level : -40dB

Preset3 : Off / Time : 3 sec / Level : -40dB

6 If you activate this function, turn the JOG to select the no

signal status judgment level (-60 to -20dB: 5dB steps) and

press the JOG.

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Preset” and press the JOG.

7 If you activate this function, turn the JOG to select the no

signal status judgment time (1 to 5 seconds) and press

the JOG.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

4 Turn the JOG to select “ManTrack” and press the JOG.

8 Press the MENU/STORE button to register the settings.

Manual track

Set the manual track.

5 Turn the JOG to select function On/Off, and press the

JOG.

If the manual track is set to On, press the REC button during

recording to record as a new track at the point when the

button was pressed.

This function can be used to create new tracks whenever

desired, making it easier to search for tracks during playback.

When manual track is set to On, the “M.TRACK” icon lights in

the display.

< Default value > Preset1 : On

Preset2 : On

6 Press the MENU/STORE button to register the settings.

Preset3 : On

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Preset” and press the JOG.

Auto track

Set auto track.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

When auto track is set to On, new tracks are automatically

created and recorded at the set time interval.

Auto track can be set to increase the number of tracks every

1, 5, 10, 15, 30 minutes, or every 1, 2, 6, 8, 12, 24 hours, or

every 640 Mbytes or 700 Mbytes.

By using this function, it is easy to search recorded contents

for specific points.

For example, if the Auto Track function is set to “every

1 minute”, the track number is updated every 1 minute.

When playing back the recorded data, you can play back

approximately the 3rd minute of the recording data by

choosing track 4. To listen directly to the 10th minute of

the recorded data, the search can be performed easily by

selecting track 11.

4 Turn the JOG to select “Auto TRK” and press the JOG.

(To search and listen from a certain number of minutes after

the start, specify the track number n+1.)

Also, when burning from the HD to a CD-R, you can also

divide the tracks by the capacity of one CD-R disc (640Mbyte

or 700Mbyte).

When auto track is set to On, the “A.TRACK” icon lights in the

display.

5 Turn the JOG to select function On/Off, and press the

JOG.

Notes

●

When both auto track and manual track are set to On at

the same time, if many tracks are created using manual

track, the relationship between track number and time will

not be consistent.

●

If background recording is set to On and a No is chosen

when recording is restarted, the data recorded by

background is erased and a new track is created.

6 When this function is activated, turn the JOG to select the

auto track time (every 1, 5, 10, 15, 30 minutes, or every

1, 2, 6, 12, 24 hours, or every 640Mbyte, 700Mbyte), and

press the JOG.

The auto track setting time is also reset and a new count is

started.

< Default value > Preset1 : Off / Time : 5 min

Preset2 : On / Time : 5 min

Preset3 : Off / Time : 5 min

1 While the recorder is stopped, press the MENU/STORE

button.

7 Press the MENU/STORE button to register the settings.

2 Turn the JOG to select “Preset” and press the JOG.

4 When CD burning is completed, the CD-R disc is

CD Burning

automatically ejected from the CD slot.

You can easily burn all of the data recorded on the HD onto

a CD-R with this recorder. You cannot specify particular data

on the HD for burning onto a CD-R. After burning onto the

CD-R, all of the data is erased from the HD.

If all of the HD data did not fit onto 1 CD-R disc, “Insert

CD” message is displayed.

Notes

• Do not attempt to playback or burn a CD while the

recorder is on a slant, standing on its edge, or on an

unstable surface.

(Displayed when 2 discs are required)

• Do not move or carry the recorder while a CD is inserted

and operating. Doing so may cause damage to the

inserted CD.

5 To continue recording the remaining HD data to CD-R,

insert the seconds CD-R disc into the recorder.

• When the CD-R disc is inserted, the recorder starts

burning HD data to the CD-R again.

1 Insert a CD-R disc into the recorder’s CD slot.

Notes

• Use CD-R discs that are compatible with the recorder. (

P.XX)

☞

• When CD burning is completed, “Complete” is displayed

for 3 seconds, and the CD-R disc is automatically

ejected from the CD slot.

• Also, if all of the data will not fit onto one CD-R disc, the

recording method for the final track can be set in [CD Split]

in the preset menu. ( P.XX)

☞

2 While the recorder is stopped, press the MAKE CD

• When CD creation is fully completed, “MoreCopy?” is

displayed.

button.

• A confirmation message to perform CD burning is

displayed.

If you select No when “MoreCopy?” is displayed, the

display switches to “FORMAT HD”.

If you wish to format the HD, select YES.

If you wish to create another CD, select No. The display

returns to “MoreCopy?”.

3 Press the MAKE CD button again to start burning all of

the HD data onto a CD-R.

• The progress status is shown in the lower character

display section.

The display is a 10-figure display, with one figure

representing 10%.

• Press the CANCEL button to cancel CD creation.

6 To burn the data again onto a different CD-R disc, turn the

JOG to select “Yes”, and press the JOG.

If you have finished burning to CD-R, select “No” and

press the JOG.

• If you selected “Yes”, CD creation starts again.

• If you selected “No”, all of the HD data is erased.

After all of the HD data is erased, “HD Clear” is

displayed for 3 seconds, after which the display returns

to the default display.

Notes

If an error occurs during CD creation, “Write_Err” is

displayed in the lower section, and the CD-R disc is

automatically ejected from the CD slot.

If a new CD-R disc is inserted, the recorder automatically

starts CD creation again.

CD Split

1 While the recorder is stopped, press the MENU/STORE

button.

When copying the HD data to CD-R disc, the recording

method for the final track when all of the data will not fit onto 1

CD is set in the CD Split function.

• CD Split On Setting

This setting uses all of the unused space on a CD-R disc

to save data.

This enables the effective use of disc space, and reduces

the number of discs required. Also, when creating a CD

with data from a meeting, etc., a 30 second overlap of the

beginning and end contents is burned to make it easier to

understand the context.

2 Turn the JOG to select “Preset” and press the JOG.

HD Data

001.wav

002.wav

003.wav

Track 1

Track 2

First CD-R

Track 1

30 sec of overlap

Track 2

Second CD-R

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

If track 001 and only part of track 002 can be saved to

the first CD-R as shown in the diagram above, track 001

and part of track 002 are saved to the first disc. Then,

the remainder of track 002 that could not be saved onto

the first disc is saved onto the second disc, starting 30

seconds before the track cut off on the first disc.

• CD Split Off Setting

The final track that could not fit onto the first CD-R is not

saved to the first CD-R, but is saved from the beginning of

the track onto the second CD-R.

Unused space remains on the disc, but it is easier to play

back these tracks because only complete tracks exist on

the same disc.

4 Turn the JOG to select “CD Split” and press the JOG.

If a track with a file size larger than the capacity of the disc

is being burned to disc, CD Split Off becomes invalid, and

the track is cut midway.

If the file size of the next track is small, CD Split Off

becomes valid again.

HD Data

001.wav

002.wav

003.wav

5 Turn the JOG to select function On/Off, and press the

Track 1

1st CD-R

2nd CD-R

JOG.

Track 1

Track 2

If only track 001 and part of track 002 can be saved onto

the first CD-R as shown in the diagram above, track 001 is

saved onto the first CD-R, and track 002 is saved from the

start onto the second CD-R.

It is convenient to use auto track. ( P.XX)

☞

Creating tracks with the desired time interval increases the

efficiency with which discs are used.

If you do not wish to create many tracks, you can create a

disc with one CD-sized track by setting the capacity of the

disc being used.

6 Press the MENU/STORE button to register the settings.

< Default value > Preset1 : On

Preset2 : On

Preset3 : On

Basic operations for playback

Playing Back HD Data

1 Press the PLAY/PAUSE button while the recorder is

stopped to play back.

Schematics

• The following information is displayed during playback.

LINE

OUT

DIGITAL

OUT

2 During playback, press the PLAY/PAUSE button to pause

playback.

3 Press the STOP button to stop playback.

• This display shows the stopped status of playback. If

you press the PLAY/PAUSE button again, the stopped

track starts playback again from the beginning of the

track.

4 Press the STOP button again to return to the stopped

status.

• Press the PLAY/PAUSE button to play back from the

first track.

[Fast reverse]

Track access

1 You can search at high speed in the reverse direction by

You can select the track that you wish to play back while the

recorder is stopped, during playback, or while playback is

paused.

holding down the 5 button while playback is paused or

stopped. The search starts from the end of the final track

while playback is stopped.

The first 3 seconds of the reverse search are performed

at 10 times speed, after which the speed automatically

increases to 140 times speed.

1 Turn the JOG to display track selection while the recorder

is stopped, during playback, or while playback is paused.

When you release the button, the recorder returns to

playback paused.

2 Select the track that you wish to play back, and press

either the JOG or the PLAY/PAUSE button to play back

the track.

Notes

If the start of the track is passed with 5 button still held

down, search moves to the previous track and continues

searching in the reverse direction.

Audible search

[Fast forward]

1 You can search audio at 2 times speed in the forward

direction while listening to the audio by holding down the

6 button during playback. Release the button to return to

[Fast forward]

normal forward direction playback.

1 You can search at high speed in the forward direction by

holding down the 6 button while playback is paused or

stopped. The search starts from the beginning of the first

track while playback is stopped.

The first 3 seconds of the forward search are performed

at 10 times speed, after which the speed automatically

increases to 140 times speed.

When you release the button, the recorder returns to

playback paused.

[Fast reverse]

1 You can search audio at 2 times speed in the reverse

direction while listening to the audio by holding down the

5 button during playback. Release the button to return to

normal forward direction playback.

Notes

If the end of the track is passed with 6 button still held

down, search moves to the next track and continues

searching in the forward direction.

Playback mode settings

You can select the playback mode from the following 4

modes.

5 Turn the JOG to select the playback mode and press the

JOG.

Mode

Mode explanation

Play back the tracks in numerical order, and

playback stops when the final track playback is

completed.

Normal

Repeat All

Repeat playback of all tracks.

Repeat Track Repeat playback of selected tracks only.

After completing playback of the tracks, playback

Single

is paused at the start of the next track.

6 Press the MENU/STORE button to register the settings.

< Default value > Preset1 : Normal

Preset2 : Normal

Preset3 : Normal

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Preset” and press the JOG.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

4 Turn the JOG to select “Play Mode” and press the JOG.

Playing Back CDs

Schematics

2 Insert a CD into the recorder’s CD slot.

3 Press the PLAY/PAUSE button while the recorder is

stopped to restart playback.

• The following information is displayed during playback.

LINE

OUT

DIGITAL

OUT

4 Press the PLAY/PAUSE button to pause playback.

CD Playback

Pay attention to the following points when playing back a CD

that was not created on the recorder.

• Data discs recorded in MP3, WAVE, and AIFF format may

contain a number of hierarchies (directory folders).

In this case, the tracks are played back in a decided order

because the recorder does not have an album (directory)

selection function.

5 Press the STOP button to stop playback.

• This display shows the stopped status of playback. If

you press the PLAY/PAUSE button again, the stopped

track starts playback again from the beginning of the

track.

• As the recorder does not have a file name display function,

only the track number starting from track 1 is displayed in

the display.

• Maximum number of hierarchies that can be played back

: 8

• Maximum number of displayable file : 999

6 Press the STOP button once again to return to the

stopped status.

• In this state, press the PLAY/PAUSE button to play back

from the first track.

You can playback a CD using the same playback mode as

HD playback. ( P.XX)

☞

Notes

• Do not attempt to playback or burn a CD while the

recorder is on a slant, standing on its edge, or on an

unstable surface.

• Do not move or carry the recorder while a CD is inserted

and operating. Doing so may cause damage to the

inserted CD.

7 Press the EJECT button to eject the CD.

[Various CD playback operations]

When playing back a CD, you can perform the following

various operations just as when playing back HD data.

Basic operations for playback

1 While the recorder is stopped, press the HD/CD button to

switch to CD playback mode.

• Track access

• Search

• Audible search

(

☞

(

☞

(

☞

P.XX)

• Playback mode settings ( P.XX)

☞

Beep sound (alarm) setting

Other Functions

If there are no operations performed for the set amount

of time for auto power off while the recorder is stopped or

playback is paused, the beep sound can be heard.

The beep sound can be heard through the speakers or

headphones.

The beep sound that occurs when the remaining battery

power is low can be heard through the headphones even if

the recorder volume is set to minimum.

Auto power off settings

If there are no operations for the set amount of time while

the recorder is stopped or playback is paused, the power is

automatically turned off.

Before the power turned off, the beep sound can be heard for

xx seconds through the speakers or headphones.

This function is used to conserve battery power.

< Default value > On

< Default value > Off / 15 min

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Beep” and press the JOG.

2 Turn the JOG to select “A.Pow Off” and press the JOG.

3 Turn the JOG to select function On/Off, and press the

JOG.

4 If this function is activated turn the JOG to select the

automatic power off (5, 10, 15, 30 minutes) and press the

JOG.

4 Press the MENU/STORE button to register the settings.

5 Press the MENU/STORE button to register the settings.

[When CD is stopped]

Switching the display mode

Depending on the status of the recorder, you can switch the

information in the display by pressing the DISPLAY button.

CD total time and total number of tracks

(Default display)

[When the HD is stopped]

Remaining recordable time on the HD

(Default display)

Current time

Total number of tracks

Recorded track information

Current time

CD total time and total number of tracks

(Return to the default display)

[When in HD recording or recording paused status]

Recording elapsed time of current track

(Default display)

Remaining recordable time on the HD

Recording format of recorded track

Recording date and time information

Remaining recordable time on the HD

(Return to the default display)

Recording elapsed time

(Return to the default display)

[When in HD/CD playback or playback paused status]

The following display screens are for HD playback.

The following display screens are for CD playback.

Playback elapsed time for the track

currently being played back

(Default display)

Playback elapsed time for the track

currently being played back

(Default display)

Level margin display

Remaining playback time for track

currently being played back

Remaining playback time for track

currently being played back

Recording format of the track being played back

Remaining playback time for all tracks

Recording format of the track being played back

Recording date and time information

Playback elapsed time for the track

currently being played back

(Return to the default display)

Playback elapsed time for the track

currently being played back

(Return to the default display)

Stop Monitor settings

5 Turn the JOG to select function On/Off, and press the

JOG.

This function constantly monitors the input signal from the

selected input source while the recorder is stopped.

When the Stop Monitor function is set to On, the level

and level margin of the currently connected input signal is

displayed in the display. Furthermore, audio is output to the

line out jack, speakers, or headphones.

Level meter display

6 Press the MENU/STORE button to register the settings.

Margin display

< Default value > Preset1 : Off

Preset2 : Off

Preset3 : Off

1 While the recorder is stopped, press the MENU/STORE

button.

Key lock settings

When the KEYLOCK switch is switched ON, all of the

operating buttons and switches are locked, except for the

LIGHT button.

1 Set the KEYLOCK switch to ON while the recorder is

stopped, paused, recording, or playing back to engage

the key lock.

2 Turn the JOG to select “Preset” and press the JOG.

• If any of the buttons (except for the LIGHT button) are

operated while key lock is engaged, the display shows

“KEY LOCKED”.

3 Turn the JOG to select the preset number that you wish to

2 Return the KEYLOCK switch to OFF to disengage the

set, and press the JOG.

key lock.

4 Turn the JOG to select “StopMonit” and press the JOG.

Various remote functions

4 Turn the JOG to select “Remote” and press the JOG.

1. Using a contact remote (contact closure) and

setting the operating mode

Set the operating mode for the switch contact connected

to the REMOTE1 jack.

There are the following 3 operating modes for when the

switch contact is opened and closed.

Wiring diagram of switch contact device

5 Turn the JOG to select the switch contact operating

mode, and press the JOG.

Switch

2.5mm mini jack

• Start / pause mode (StartPause)

Open / Close : Playback or recording starts.

Close / Open : Playback or recording pauses.

• Start / pause + track increment mode (StartPauTR)

Open / Close : Playback or recording starts.

Close / Open : Playback or recording pauses.

Creates a new track during recording.

6 Press the MENU/STORE button to register the settings.

• Manual track mode (Manual TRK)

Open / Close : Creates a new track.

Close / Open : No operation.

< Default value > Preset1 : Manual TRK

Preset2 : StartPauTR

2. Microphone remote connection

Optional jack for the microphone remote RC600PMD

(sold separately). The RC600PMD is a small unit that

can be attached to the microphone.

As the recorder can be controlled by hand while holding

the microphone, this is a very useful device in situations

such as recording interviews, etc.

Preset3 : StartPause

1 While the recorder is stopped, press the MENU/STORE

button.

2 Turn the JOG to select “Preset” and press the JOG.

• Microphone remote RC600PMD has 3 buttons, REC,

REC PAUSE, and MARK, which perform the same

functions as the buttons on the recorder.

3 Turn the JOG to select the preset number that you wish to

set, and press the JOG.

However, as the CDR310 does not have a marking

function, the MARK button cannot be used.

• The microphone remote has 1 LED that serves as the

REC indicator and peak indicator.

(REC indicator)

Lights red during recording, and flashes red while

recording is paused.

(Peak indicator)

Initialization of preset settings

Returns the settings of the selected preset number to default.

Lights orange when the source level becomes the same

level as [OVER] on the level meter during recording or

recording pause.

1 While the recorder is stopped, press the MENU/STORE

button.

However, it lights green when in standby (statuses other

than recording and recording pause). Orange (peak)

takes precedence over red in the display.

Margin display

For this reason, a precise clip margin (amount of margin

from the current source level at 0dB) is displayed in –dB. The

value is held in the same way as for peak hold. Press the

CANCEL button to reset it.

2 Turn the JOG to select “Preset” and press the JOG.

Margin display

CD-TEXT, ID3 tag

3 Turn the JOG to select the preset number that you wish to

There is no text display function on the recorder. However,

the Time/Date stamp (the recording start date and time for a

certain file) information can be recorded as text information.

This is so file recording information can be seen on a regular

CD player. The information is recorded in the title areas for

both, as CD text for CD-DA, and as an ID3 tag for MP3.

These text displays can be displayed on CD players that

support these text displays.

set, and press the JOG.

4 Turn the JOG to select “Default” and press the JOG.

• At this time, a default process confirmation screen is

displayed. Press the JOG to perform the process.

• After default processing, “Completed” is displayed for

1 second, and the settings only for the selected preset

number are returned to the default values. After that, the

recorder returns to the stopped status.

There is no signal from the microphone input.

• Check the input source settings. ( P.XX)

Troubleshooting

☞

• Check the recording level settings. ( P.XX)

☞

If you think a malfunction has occurred, there may be no

need to contact the dealer or the repair service counter.

Please check the following points. You can easily solve many

problems without needing to ask for professional help. If

the problem cannot be solved even after performing these

checks, contact your dealer.

• Check if the microphone requires Phantom power. (

P.XX)

☞

Cannot change recording format.

• There is only one HD recording format.

If tracks already recorded in a certain format already

exist, the format cannot be changed.

CD, or format the HD.

Recorder power will not turn on.

• Insert new batteries.

• If you are using rechargeable batteries, recharge the

batteries.

• Check the connection of the AC adaptor.

Too much noise

• Check the cable connection between each device.

Replace the cable if required.

• Check that the recording level is suitable.

The recorder power turns itself off after it is turned on.

• Insert new batteries.

Care and maintenance

There is no sound from the internal speakers.

• Check the LEVEL volume setting on the front side of the

recorder.

Dip a soft cloth into water mixed with a small amount of

neutral detergent, wring out the cloth, and gently wipe the

recorder.

• Check the ON/OFF position of the speaker switch on the

front side of the recorder.

Cannot record

• Check that the input source settings are correct.

• Check to see if the maximum number of tracks, 999

tracks, have been recorded.

• Check that there is enough recording time remaining on

the HD.

Error Messages

Display

Full_HD

Full_999

No Track

No Disc

Description

There is no space remaining on the HD.

Error messages

The track number on the HD has reached the maximum number, track 999.

No track files detected.

No disc in the CD slot.

Blank Disc

No files detected on the CD.

Cannot synchronize the signal because the sampling frequency of the digital input

signal is not 44.1kHz.

Unlocked

Write_Err

Read_Err

Format_Err

Err_MPU

Write to the HD or CD-R failed.

Read from the HD or CD-R failed.

Formatting failed.

MPU error detected.

Err_HD

HD error detected.

Err_CDR

CD-R drive error detected.

Real Time Clock error detected.

EEPROM error detected.

SRAM error detected.

Err_RTC

Err_EEPROM

Err_SRAM

LowBattery

Not Blank

KEY LOCKED

ALC On

Warning messages

System messages

Battery voltage is low.

There is no writable CD-R disc in the CD-R slot.

Key Lock is engaged.

The recording level control is set by ALC.

Output

Specifications

LINE OUT L/R

Digital audio system

Type ............................................................... RCA terminal

Standard level ................................... 2 Vrms max./2 kohms

DIGITAL OUT

Type ............................................................... RCA terminal

Output impedance ................................................. 75 ohms

Standard input/output level ..................................... 0.5Vp-p

Sampling frequency .............................................. 44.1 kHz

Format ...................................................................... SPDIF

System ................................................................ HD recorder

Recording media ............................................... 1-inch 4G HD

Writing CD media ........................................................... CD-R

Recording format

MP3 ( .mp3) ........................ MPEG1 layer 3 compression

WAV ( .wav) ...........................................16-bit linear PCM,

WAVE file format

AIFF ( .aif) ...............................................16bit linear PCM,

Audio Interchange File format

CD ( .cda) .............................................16bit linear PCM,

CD audio file format

General

Headphone output ........................................ 8 mW/ 32 ohms

Speaker output ............................................ 150 mW/ 8 ohms

Phantom power .................................................... + 48V, 5mA

Power consumption

Recording .......................................................... 5.0 W(DC)

Playback ............................................................ 5.0 W(DC)

Battery lifespan ............................... 4 hours (standard value)

Dimensions

Width ....................................................................... 113 mm

Height ....................................................................... 47 mm

Length ................................................................. 183.5 mm

Weight......................................................................... 0.5 kg

Recording bit rate

MP3 .......................................... 128 kbps (mono : 64 kbps)

WAV ................................... 1412 kbps (mono : 705.5 kbps)

AIFF ................................... 1412 kbps (mono : 705.5 kbps)

CD ...................................... 1412 kbps (mono : 705.5 kbps)

Sampling frequency ................................................. 44.1 kHz

Channel ................................................... 2 (stereo), 1 (mono)

Frequency characteristics ........................ 16,000 Hz (-0.5dB)

S/N ratio

IEC-A load ......................................................... LINE 80 dB

MIC 60 dB

Overall height harmonic distortion by 0 VU (wav)

.............................................................................. LINE 0.06%

MIC 0.06%

Provided accessories

Dynamic range .............................................................. 80 dB

AC adaptor ............................................................................ 1

AA battery holder ................................................................... 1

User’s guide ...........................................................................1

Input

MIC IN L/R

Type ................................... XLR (1:GND, 2:HOT, 3:COLD)

Input sensitivity (MIC) ...................... 1.0 mVrms/6.5 kohms

LINE IN

Type ............................................................... RCA terminal

Input sensitivity ................................ 500 mVrms/20 kohms

DIGITAL IN

Accessories sold separately**

(Please refer to http://www.d-mpro.com/ for descriptions and

ordering information.)

Wired remote control ........................................... RC600PMD

Type ............................................................... RCA terminal

Input impedance .................................................... 75 ohms

Standard input/output level ..................................... 0.5Vp-p

Sampling frequency .............................................. 44.1 kHz

Format ...................................................................... SPDIF

* Specifications are subject to change without prior notice.

Exclusion of Damages (Americas only)

LIMITED WARRANTY

Your Marantz Professional product is warranted against

manufacturer defects in material and workmanship for a

period of one year parts and labor.

Liability for any defective product is limited to repair or

replacement of the product at manufacturer’s option.

Manufacturer shall not be liable for damage to other products

caused by any defects in Marantz products, damages based

on inconvenience or loss of use of the product, or any other

damages, whether incidental, consequential, or otherwise.

Except as specified below, this warranty covers defects in

material and workmanship. The following are not covered

under warranty:

Some States do not allow limitations on how long an implied

warranty lasts and/or do not allow the exclusion or limitation

of incidental or consequential damages, so the above

limitations and exclusions may not apply to you.

1. Damage, deterioration, malfunction or failure to meet

performance specifications resulting from:

a)Accidents, acts of nature, misuse, abuse, neglect or

unauthorized product modification.

How State Law Relates to the Warranty (Americas only)

This warranty gives you specific legal rights, and you may

have other rights which may vary from State to State.

b)Improper installation, removal or maintenance, or failure

to follow supplied instructions.

c)Repair or attempted repair by a non-Marantz authorized

agent.

Marantz Professional Service Number (Americas only):

Marantz Professional Factory Service (630) 741-0330, toll

free within the US (866) 405-2154.

d)Any shipment (claims must be presented to the carrier).

e)Any cause other than a defect of manufacturing.

2. Cleaning, check-ups with no fault found or changes

incurred for installation, removal or reinstallation of the

product.

3. Any serialized product on which the serial number has

been defaced, modified or removed.

Products purchased outside of the United States, its

possessions or territories.

This warranty is enforceable only in the United States and its

possessions or territories.

Marantz Professional products Sales Office Site:

For inquiries or information on repair service of Marantz

Professional Products, please contact our Sales Office

or Tech Support Centre near you which are listed in D&M

Professional website below.

4. Batteries and battery chargers.

5. Accessories, including but not limited to: cables, mounting

hardware and brackets, cleaning accessories, power cords

and adapters, and carry cases.

Non-transferable warranty

This Warranty may be enforced only by the original

purchaser.

AMERICA

D&M Professional America http://www.d-mpro.com

Service number : 866-405-2154 (Toll Free)

EUROPE

What We Will Pay For

We will pay for all labor and material expenses for items

covered by the warranty.

D&M Professional Europe

http://www.d-mpro.eu.com

ASIA / OTHERS

HowYou Can Get Service (Americas only)

1. If your unit needs service in the USA, contact our service

referral at the appropriate telephone number indicated

below. We will advise you of the name and location of one

or more authorized service centers from which service

may be obtained. Please do not return the unit directly to

us.

Marantz Korea Co.,Ltd.

DENON Asia Co.,Ltd.

D&M Electronics Singapore Pte. Ltd.

http://www.denonsingapore.com

http://www.marantz.co.kr

http://www.denon.com.hk

2. You must pay any shipping charges if it is necessary

to ship the product for service. If the necessary repairs

are covered by the warranty, we will pay return shipping

charges to your location anywhere in the United States or

its territories.

3. Whenever warranty service is required, you must present

the original dated sales receipt or other proof of date

purchased.

Limitation of Implied Warranties

All implied warranties, including warranties of merchantability

and fitness for a particular purpose, are limited in duration to

the length of this warranty.

D&M Holdings Inc.

PROFESSIONAL BUSINESS COMPANY

Printed in Japan

08/2006

00M28BS851250 ecmf-e

Intel Computer Hardware 48201201 User Manual
JVC KD G312 User Manual
Lenovo 3000 N500 User Manual
LG Electronics RH199H User Manual
Mustek LM 3000 User Manual
NEC AccuSync AS171 User Manual
Nortel Networks Cordless Telephone C3060 User Manual
Panasonic TH 32LR11UK User Manual
Parkinson Cowan OVATION 60 GLXA User Manual
Philips SmartCard PPC927C User Manual