Magnavox MDV650R User Manual

Safety Information

Safety Precautions

Warning:To prevent fire or shock hazard, do not expose this equipment o rain or moisture.

Federal Communications Commission (FCC) Warning: Any unauthorized changes or modifications to this equipment void the user’s

authority to operate it.

Laser Safety

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible

eye injury.

CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous

radiation exposure. The set complies with the FCC-Rules, Part 15 and with 21 CFR 1040.10.

CAUTION: Visible and invisible laser radiation when open and interlock defeated. Do not stare into the beam. The beam is located

inside, near the deck mechanism.

Special Information for Canadian Users

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio

Interference Regulations of the Canadian Department of Communications.

Radio/TV Interference

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and the receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

Note to Cable TV system installer:

This reminder is provided to call the Cable TV(CATV) system installer 's attention to Article 820-40 of the NEC (National Electrical

Code) that provides guidelines for proper grounding and, in particular, specifies that the cableground shall be connected to the

grounding system of the building, as close to the point of cable entry as practical.

Unauthorized copying, broadcasting, public performance and lending of Discs are prohibited. This product incorporates copyright

protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by

Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision

Corporation and is intended for home andother limited viewing uses only unless otherwise authorized by Macrovision Corporation.

Reverse engineering or disassembly is prohibited.

Declaration ofConformity

Model Number:

Trade Name:

MDV630R/MDV650R

MAGNAVOX

Responsible Party:

Philips Consumer Electronics

P.O. Box 14810, Knoxville, TN 37914-1810(865) 521-4316

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

11.Only use attachments/accessories specified by the

manufacturer.

12.

Use only with a cart, stand, tripod, bracket, or

table specified by the manufacturer or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid

injury from tip-over.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

13.Unplug this apparatus during lightning storms or when

unused for long periods of time.

7. Do not block any ofthe ventilation openings. Install

inaccordance with the manufacturer’s instructions.

14.Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as if the power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen into the

8. Do not install near any heat sources such as

radiators,heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

apparatus, or if the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

9. Do not defeat the safety purpose

of the polarized or grounding-type

15.Battery usage CAUTION - To prevent battery

leakage which may result in bodily injury or damage to the

plug. A polarized plug has two blades

with one wider than the other.

unit:

• Install all batteries correctly, + and @ as marked on the

unit.

• Do not mix batteries (old and new or carbon and

alkaline , etc.).

• Remove batteries when the unit is not used for a

longtime.

A grounding type plug has two blades and a third grounding

prong. The wide blade or third prong are provided for your

safety. When the provided plug does not fit into your

outlet,consult an electrician for replacement of the obsolete

outlet.

10.Protect the power cord from being walked on or

pinched, particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus.

EL 6475@E003:01/6

The remote control

MONITOR

STANDBY m

TV/DVD

Monitor: To switch between the internal tuner of the DVD recorder

(TV reception) and playback of the DVD recorder

Switch on or off: To switch set on or off, interrupt menu function,

interrupt a programmed recording (TIMER)

TV/DVD: To connect the antenna signal directly to the TV. This button

lets you switch between the DVD recorder and the antenna signal. This

function operates when the DVD recorder is connected to the TV with

only an antenna cable.

T/C

Title/Chapter: To directly select a ' '(title)/' '(chapter) in the menu

bar

If 'INFO' appears in the display, the index menu of the loaded disc will

appear or an introduction will play. In this case, this function will not be

available.

PLAY MODE

REC. MODE

Playback mode: To select Repeat, Shuffle, and Intro Scan

Recording mode (quality): To select the maximum possible

recording duration

0..9

Number buttons: 0 - 9 Use to select TV channels.

DISC-MENU

SYSTEM-MENU

Disc Menu: To display the DVD menu or index screen

System Menu: To display/hide the main menu (menu bar at top of

screen)

SELECT

Select: To select a function

Store/Confirm: To store or confirm an entry

Cursor : To move left, right, up, or down

D C A B

RETURN

Back: To return to the previous menu step on a video CD (VCD). This

also functions with some DVDs.

CLEAR

Delete: To delete last entry or clear programmed recording (TIMER)

Plus: Next channel

CHANNEL q

CHANNEL r

PLAY/PAUSE G9

Minus: Previous channel

Play/Pause: To play a recorded disc.

When this button is pressed during playback, the disc is paused. You will

see a still picture.

When this button is pressed during recording, the disc recording is

paused.

Previous Chapter Track/Reverse search:

Pressing this button once during playback will return to the previous

chapter/track/ title or to the beginning of the current title/chapter/track.

If this button is held down during playback, it will search backward.

If this button is held down during a still picture, it will search backward

in slow motion.

Next title/Chapter/Track/Forward search:

Pressing this button once during playback will jump to the next

chapter/track.

If this button is held down during playback, it will search forward.

If button is held down during a still picture function, it will search

forward in slow motion.

STOP h

Stop: To stop playback/recording, except with programmed recordings

(TIMER)

Holding down the button will open and close the disc tray.

REC/OTR n

Record: To record the current TV channel

EDIT

EDIT: To display the edit menu for DVD+R(W) discs; DVD +R or

DVD+RW to set chapter marker

TIMER

TIMER: To make a TIMER programming with VCR Plus+^®system /

without VCR Plus+^®system or to alter or clear a programmed TIMER

Additional TV functions

TV VOLUME q

TV volume: Increase TV volume

TV VOLUME r

TV volume: Reduce TV volume

For the following functions, you must hold down the side button DVD/TV and then select the

function with the corresponding button. For the following functions, you must hold down the

side button DVD/TV while pressing the other button.

0..9

Number buttons: 0 - 9: Use to select TV channels.

CHANNEL q

CHANNEL r

TV channel number: TV Channel: Select the next highest TV channel.

TV channel number: TV Channel: Select the next lower TV channel.

Front ofthe Recorder

STANDBY/ON

Switch on or off: To switch off or on, interrupt a function, interrupt a

programmed recording (TIMER)

CHANNEL r

CHANNEL q

REC MODE

RECORD

Select: Channel forwards

Select: Channel backwards

Recording mode (quality): To select a recording quality.

Record: To record the currently selected TV channel

RECORD LED

Recording in progress: Red light in the RECORD button indicates a

recording is in progress.

OPEN/CLOSE

Open/Close disc tray: to open/close disc tray

Previous title/Reverse search

Next title/Forward search

hSTOP

Stop: To stop playback.

G9PLAY/PAUSE

Playback/Pause: To play a disc, pause playback, still picture

Behind the door at the lower left front

corner

S-VIDEO

S@Video jack : Input for SVHS/Hi8 camcorders or SVHS/Hi8 video

recorders (channel number 'CAM1')

Yellow jack

Video input jack: Input for camcorders or video recorders (channel

VIDEO

number 'CAM1')

White/Red jack

Audio left/right (CAM1) : Input for camcorders or video recorders

left AUDIO right

(Channel number 'CAM1')

Switching between jack S-VIDEO and VIDEO is automatic. In case both jacks are occupied,

S-VIDEO has priority.

Back ofthe Recorder

4MAINS

ANTENNA

Power plug: Connection to the power outlet (110V/60Hz)

Antenna input: Connect your antenna or Cable TV signal here.

Antenna output: Connection to the TV

Input jacks

IN S-VIDEO (Y/C)

S@Video input: Connection for an additional device (channel number

'EXT2'). Switching between jack IN S-VIDEO (Y/C) and IN VIDEO

(CVBS) is done automatically.

IN VIDEO (CVBS)

Video input (yellow jack): Connection for an additional device

(channel number 'EXT2')

IN L AUDIO R

IN AUDIO L R

Analog audio input (red/white jack) underneath jack IN VIDEO

(CVBS) . Audio for jack IN VIDEO (CVBS) : Connection for an

additional device (channel number 'EXT2')

Analog audio input (red/white jack) next to jack IN

COMPONENT VIDEO : Connection for an additional device. Audio

input for component video (channel number 'EXT2')

IN COMPONENT

VIDEO

Component video input (red/blue/green jack): Connection for an

additional device with component video input (channel number 'EXT3')

Output jacks

OUT S-VIDEO (Y/C) S@Video output: Connection for a S-video-compatible TV

OUT VIDEO

(CVBS)

Video output (yellow jack): Connection to TV using a video input

(CVBS, Composite Video)

OUT L AUDIO R

Analog audio output (red/white jack) underneath jack IN VIDEO

(CVBS) . Audio for jack OUT VIDEO (CVBS) : Connection for an

additional device

OUT AUDIO LR

Analog audio output (red/white jack): Connection for an additional

device. Audio output for component video

OUT COMPONENT

VIDEO

Component video output (red/blue/green jack): Connection for

an additional device with component video output

DIGITAL AUDIO

OUT

Digital audio output: Connection for a digital audio devices

(amplifier/receiver)

The symbols on your DVD recorder

display

The following symbols may appear on your DVD recorder display:

TITLE

Displays the title number selected/being played

Displays the track selected/being played (VCD/CD)

TRACK

DVD+RW

Displays the type of disc inserted: DVD/DVD+R/DVD+RW; DVD-R

and DVD-RW' are displayed as DVD.

S-VCD

Displays the type of CD-disc inserted: S VCD/VCD/CD

Recording mode (quality)/Playback mode HQ, SP+, EP, EP+.

CHAPTER

Displays the chapter selected/being played

Displays total play time

TOTAL TIME

REMAIN

TIME

Displays remaining play or recording time

TIME

Displays current elapsed time

DTS

A DTS (Digital Theatre System) audio signal is available

A Dolby Digital audio signal is available

A MPEG audio signal is available

DD-DIGITAL

MPEG

PCM

A PCM audio signal is available

CHANNEL

Channel

Playback in progress. Flashes when Recorder is reading a disc.

Playback/Recording interrupted (Pause)

Recording in progress

RECORD

o((

Remote control command has been sent

A recording (Timer) has been programmed

STEREO

During playback a hifi/2-channel audio signal is recognized, or a

hifi/2-channel audio signal is received

Modulator is switched off. The antenna signal (RF signal) is only

connected to the TV when the modulator is switched off.

SAP

Second audio program from the tuner is selected.

Multifunction display/text line

•) Time

•) Disc/Title play time

•) OTR time

•) Title name

•) Display of TV channel number / disc position / channel name /

function.

•) Display of information, warnings

Messages on your DVD recorder display

READING

The following messages may appear on your DVD recorder display. If you name a disc, the disc

name will appear on the display panel as well.

IS TV ON?

The DVD recorder is currently in the initial installation mode. Switch on

your TV and read section 'Initial installation' in chapter 'Installing your

DVD recorder.'

NO SIGNAL

No signal or poor signal strength

The menu display is on.

OPENING

TRAY OPEN

CLOSING

READING

MENU UPDT

INIT MENU

Disc tray is opening.

Disc tray is open.

Disc tray is closing.

Disc is being read.

After a successful recording, the list of disc contents is updated.

After the first recording has been successfully completed on a new disc,

the menu structure is created.

COPY PROT

WAIT

The DVD/video cassette you are trying to copy is copy protected.

Please wait until this message disappears. The DVD recorder is busy

processing another operation.

NO DISC

No disc has been inserted. If a disc has been inserted, then it is possible

that the disc cannot be read.

INFO

Information on the inserted DVD is displayed on the screen.

The DVD Recorder is busy making changes DVD-compatible.

Entire disc is being erased.

BUSY

ERASING

EMPTYDISC

Inserted disc is new or has been completely erased (no recordings

present).

PROTECTED

MAX TITLE

Disc cannot be recorded on.

The maximum number of titles has been reached for the disc. Each disc

can have a maximum of 48 titles.

MAX CHAP

The maximum number of chapters per title/disc has been reached. The

maximum number of chapters per title is 99, and 124 per disc.

DISC FULL

PAL DISC

Disc is full. There is no room for new recordings.

A disc with PAL recordings has been inserted and an attempt was made

to establish a NTSC signal. Insert a new disc or use a disc containing

NTSC recordings.

NTSC DISC

A disc with NTSC recordings has been inserted and an attempt was

made to establish a PAL signal. Insert a new disc or use a disc containing

PAL recordings.

RECORDING

An unauthorized action was attempted during recording (e.g. pressing

the OPEN/CLOSE button).

FREETITLE

DISC LOCK

The following title is empty.

An attempt was made to record on a protected disc during playback.

This message will also appear when an attempt is made to insert a

chapter marker( EDIT button).

DISC ERR

An error occurred when writing the title. If this happens often, please

clean the disc or use a new one.

Read section 'Cleaning discs' in the next chapter on how to clean the

disc.

DISC WARN

SETUP

An error occurred when writing the title. The recording will continue,

but the error will be skipped.

After the automatic channel search, the time/date menu appears on the

screen.

WAIT 01

During automatic channel search, the detected TV channels are

counted.

BLOCKED

It is not possible to close/open the disc tray.

SAFE REC

The new recording will be added to the end of all recordings (SAFE

RECORD).

Table ofcontents

Playing a DVD+RW or DVD+R ................................................................. 44

Playing audio CDs .......................................................................................... 45

Playing MP3 CDs ............................................................................................ 45

Playback of a (Super) Video CD ................................................................. 46

Introduction .................................. 13

Dear Magnavox customer, ........................................................................... 13

Region codes ................................................................................................... 16

Technical data ................................................................................................. 16

Accessories ...................................................................................................... 16

Important notes regarding operation ........................................................ 17

Cleaning discs .................................................................................................. 18

Special functions of your new DVD recorder ......................................... 18

Other playback functions............. 47

Changing to a different chapter track/title ............................................... 47

Disc search ...................................................................................................... 47

Still picture ....................................................................................................... 48

Slow motion .................................................................................................... 48

Search with time entry .................................................................................. 49

Repeating/Shuffle ............................................................................................ 49

Repeat a specific segment A-B .................................................................... 50

Scan function ................................................................................................... 50

Zoom function ................................................................................................ 51

Camera angle ................................................................................................... 51

Changing audio language ............................................................................... 52

Subtitles ............................................................................................................ 52

Connecting the DVD recorder ... 20

Preparing the remote control for operation ........................................... 20

Connecting your DVD recorder to the TV ............................................. 20

Connecting with a Component Video (Y Pb Pr) cable .......................... 22

Connecting with a S-Video (Y/C) cable .................................................... 23

Connecting with Video (CVBS) .................................................................. 24

Connecting only with the antenna cable ................................................... 25

Connecting additional devices .... 27

Recording ...................................... 53

Connecting an additional video recorder ................................................. 27

Connecting a camcorder to the front jacks ............................................. 28

Connecting audio devices to analog audio jacks ..................................... 28

Connecting audio devices to the digital audio jack ................................. 29

General information ...................................................................................... 53

Recording without automatic switch-off ................................................... 54

Pausing recording ........................................................................................... 56

Recording with automatic switch-off (OTR one-touch-recording) .... 56

Preventing accidental erasing of discs ........................................................ 57

Lining up recordings within a title (assemble cut) .................................. 58

Installing your DVD recorder...... 30 Selecting the recording mode (quality) ..................................................... 59

Initial installation ............................................................................................. 30

Automatic TV channel search ..................................................................... 32

Adding and deleting TV channels manually ............................................... 33

Setting the language ....................................................................................... 34

Switching audio recording (stereo, SAP) .................................................. 35

VCR Plus+^®Guide channel numbers ......................................................... 36

Setting the time/date automatically ............................................................ 37

Manually setting the time & date ................................................................ 38

Managing disc content ................. 60

General information ...................................................................................... 60

Editing recording titles (name) .................................................................... 61

Playing the entire title ................................................................................... 61

Deleting recordings/titles ............................................................................. 62

Disc settings .................................................................................................... 63

Changing disc name ....................................................................................... 63

Finalize editing ................................................................................................. 64

Information on the TV screen .... 39 Finalizing DVD+R discs ................................................................................. 64

Erasing DVD+RWs ........................................................................................ 65

Edit menu ......................................................................................................... 65

Changing the index picture .......................................................................... 65

Splitting titles ................................................................................................... 66

Menu bar icons ............................................................................................... 39

Menu bar 1 ....................................................................................................... 39

Menu bar 2 ....................................................................................................... 39

Field for temporary messages ..................................................................... 40

Status box ........................................................................................................ 40

Disc type icons ................................................................................................ 40

Disc status icons ............................................................................................. 41

Tuner info box ................................................................................................ 41

Timer info box ................................................................................................ 41

Programming a recording

(TIMER) .............................................. 67

General information ...................................................................................... 67

Programming a recording (with VCR Plus+^®system) ............................ 67

Programming a recording (without VCR Plus+^®system) ..................... 69

How to check, change, or delete a programmed recording (TIMER) 70

Problem solving for programmed recordings .......................................... 71

Playback ........................................ 42

General information regarding playback ................................................... 42

Inserting a disc ................................................................................................ 42

Playing a DVD ................................................................................................. 43

Table of contents

User preferences .......................... 72

Picture settings ................................................................................................ 73

Sound settings ................................................................................................. 73

Language settings ............................................................................................ 74

Additional settings .......................................................................................... 75

Child lock....................................... 76

Child lock (DVD and VCD) ......................................................................... 76

Activating/Deactivating the child lock ........................................................ 76

Authorizing discs ............................................................................................ 77

Locking authorized discs ............................................................................... 77

Parental control (DVD video only) ............................................................ 78

Activating/Deactivating the parental control ............................................ 78

Changing the country .................................................................................... 79

Changing the PIN ........................................................................................... 80

Before you call technical support 81

Table of contents

AIntroduction

Dear Magnavox customer,

Instruction manuals are usually very dry since they are technically-oriented and often poorly

translated. I have been employed by Magnavox for this reason.

Allow me to introduce myself.

My name is Phil. I will be guiding you through the instruction manual and try to be of help in

operating your new device. At appropriate points along the way, I will be providing you with the

following information:

(Question)?

Tip

Problem

Here I will be explaining

seemingly unimportant things.

Here I will be giving you

instructions on functions that

help make it easier to use your

DVD Recorder.

Here I will help you find the

cause of problems and their

solutions.

I hope you have lots of fun with your new DVD Recorder.

Phil

P.S. If you have questions or if problems come up during operation, please see the helpful

information in the chapter 'Before you call technical support. If this doesn't help you resolve the

problem, please call the customer support service for your country.

The corresponding telephone numbers and e-mail addresses are listed in the warranty booklet

provided.

Introduction

Welcome to the large family of Magnavox DVD owners.

Thank you for buying a MDV630R/MDV650R .

Please take the time to read this owner's manual before using your DVD recorder. It contains

important information and notes regarding operation.

The DVD recorder should not be turned on immediately after transportation from a

cold to a hot area or vice versa, or in conditions of extreme humidity.

Wait at least three hours after transporting the device. The DVD recorder needs this to

acclimate to its new environment (temperature, air humidity, etc.).

Your Magnavox team hopes you

will enjoy

using your new DVD recorder.

What is a DVD?

DVDs (Digital Video Discs) are the new storage medium that combines

the convenience of the Compact Disc with the latest advanced digital

video technology. DVD Video uses state-of-the-art MPEG2 data

compression technology that allows an entire film to be put on a single

5-inch disc.

How high is the resolution compared to VHS?

The crystal-clear digital pictures have a resolution of over 500 lines, with

720 pixels (picture elements) per line. This resolution is more than

double that of VHS and is superior to Laser Discs. The quality can be

compared to digital masters made in recording studios.

What is DVD+RW?

DVD+ReWritable (DVD+RW) uses phase-change media, the same

technology that formed the basis for CD-ReWritable. A high-power laser

is used to change the reflectivity of the recording layer. This process

means the disc can be recorded on more than a thousand times.

What is DVD+R?

DVD+R (recordable DVD). In contrast to DVD+RW, this disc can only

be recorded once. If a disc has not been finalized after recording, it can

continue to be recorded upon in the DVD Recorder. Old recordings can

be later deleted, but they cannot be overwritten. The deleted titles are

marked as 'Deleted title.'

For this disc to be played in a DVD player, it must be 'finalized' in the

DVD recorder. After this has been completed, no further recordings can

be added.

What can my DVD recorder do?

Your Magnavox DVD recorder is a recorder and player for digital video

discs, with a two-way compatibility to the universal DVD Video standard.

This means that:

•)existing pre-recorded DVDs can be played.

•)recordings made on your DVD recorder can play on existing DVD

Video players and DVD-ROM drives. In some cases, the discs may have

to be finalized before they will play on other DVD players.

Introduction

Compatible discs

Using this DVD recorder, you can play and record on the following discs:

Recording and Playback

DVD+RW (Digital Versatile Disc + Rewritable); can be recorded on over and over.

DVD+R (Digital Versatile Disc + recordable); can be recorded on once.

Playback only:

DVD Video (Digital Versatile Disc)

DVD-R (DVD-Recordable)

DVD-RW (DVD-Rewritable) Can only be played back when the recording was made in 'video

mode' and the recording was finalized.

Audio CD (Compact Disc Digital Audio)

Super Audio CD (only plays the CD layer of a hybrid SACD disc)

Video CD (Formats 1.0, 1.1, 2.0)

Super Video CD

CD-R (CD-Recordable) Audio/MP3 contents

CD-RW (CD-Rewritable) Audio/MP3 contents

Introduction

Region codes

Because DVDs are not released at the same time in all regions of the world, all DVD players are

keyed to a specific region code. Discs can be assigned an optional region code. If the region

codes of the player and disc do not match, playback is not possible.

This device will only play Region 1 DVDs or DVDs manufactured to be played in all regions ('ALL').

DVDs from other regions cannot be played in this DVD recorder.

The number within the globe represents the region of the world.

Region 1 represents:

U.S, Canada, upper regions of North America, Bermuda, U.S. Virgin Islands and smaller regions near

Australia.

Technical data

Voltage : 110-130V/60Hz

Power consumption : 25W

Power consumption (Standby): Less than 3W (clock display off)

Measurements in cm (W/H/D): 43.5/8.8/32.6 (disc tray closed), 46.1 cm (disc tray open)

Weight without packaging approx.: 4.0kg

Power failure/no power supply: Channel and timer data will remain stored for approx. 1 year,

the clock data for approx. 12 hours.

Operating position: max. inclination of 10 degrees in any direction

Ambient temperature: 59°F - 95°F

Humidity: 25% - 75%

Accessories

Owner's manual

Warranty booklet

Quick-start guide

Remote control and batteries

Antenna cable

Power cable

Audio cable (with red/white plugs)

Video cable (with yellow plugs)

Accessories MDV@630R

1x DVD+RW

Accessories MDV@650R

2x DVD+RW

3x DVD+R

Introduction

Important notes regarding operation

Caution!

Visible and invisible laser radiation. When open avoid exposure to beam.

Because of the danger of eye injury, only qualified service personnel should remove the cover or

attempt to service this device.

LASER

Type: Semiconductor laser InGaAlP (DVD), AlGaAs (CD)

Wavelength: 660nm (DVD), 780nm (CD)

Output power (out of objective): 20mW (DVD+RW writing), 0.8mW (DVD reading), 0.3mW (CD

reading).

Beam divergence: 82 degrees (DVD), 54 degrees (CD)

Danger: High voltage! Do not open!

There is a risk ofan electrical shock!

The machine does not contain any components that can be repaired by the customer. Please leave

all maintenance work to qualified personnel.

As soon as the DVD recorder is connected to the power supply, there are some components

that are in constant operation. To switch off the DVD recorder completely you must disconnect

it from the power supply.

If you disconnect the DVD recorder from the power supply, pull out the power cord's plug from

the wall outlet, not only the plug from the jack 4MAINS at the rear of the set. Children playing

near the device could suffer injuries at the free end of the cable.

These operating instructions have been printed on non-polluting paper.

Deposit old batteries at the appropriate collection points.

Please make use of the facilities available in your country for disposing of the packaging in a way

that helps to protect the environment.

This electronic device contains many materials that can be recycled. Please enquire about the

possibilities for recycling your old device.

Introduction

In a cabinet, allow about 2.5 cm (1 inch) of free space around the recorder for adequate

ventilation.

Make sure that air can circulate freely through the ventilation slots on the machine. Do not place

the device on an unsteady base.

Make sure that no objects or liquids enter the recorder. Do not place vases or similar objects

on the DVD recorder. If liquid spils into it, immediately disconnect the recorder from the power

supply and call Magnavox for advice.

Keep the DVD recorder away from domestic heating equipment and other sources of heat, as well

as direct sunlight.

Do not place any combustible objects on the device (candles, etc.).

Make sure children do not place any foreign objects into the openings or the disc tray.

Cleaning discs

Some problems occur because the disc inside the recorder is dirty (frozen picture, sound

disruptions, picture distortions). To avoid these problems, discs should be cleaned on a regular

basis.

When a disc is dirty, clean it with a soft cloth. Wipe the disc

from the center to the edge in a straight line.

Do not use solvents such as benzine, thinner, commercially

available cleaners, or anti-static sprays intended for analog discs.

Can I use a cleaning disc intended for DVD players?

Since the optical unit (laser) of the DVD recorder operates at a higher

power than regular DVD or CD players, these kinds of cleaning CDs

may damage the optical unit (laser).

Therefore, refrain from using a cleaning CD!

Special functions of your new DVD

recorder

Your MAGNAVOX DVD recorder has special functions that will make day-to-day use of your

new DVD recorder easier for you.

This screen provides you with an overview of the inserted disc. Each index screen corresponds

to a recording. At the right-hand side of the screen, a disc pointer is shows the duration and

position on the disc of the selected recording.

MP3 files are highly compressed pieces of music. The amount of data of the original audio material

is reduced by 1/10 of the original size using a special process. This enables you to fit up to 10 hours

of music on a single CD.

These kinds of music CDs can be played using this recorder.

Introduction

Normally, a new recording is made on the current location on the disc. This is the same with

video cassettes. However, by holding down REC/OTR n , the new recording will be made after

the last recording on the disc. This helps you avoid recording by mistake.

New recordings on a DVD+R disc will always be added after the end of all recordings.

The Magnavox DVD recorder can play DVDs and CDs. DVDs made using this DVD recorder can

be played in most other DVD players.

This is a standard from Dolby Laboratories for the transmission of 5.1 channel sound. This

acoustical playback system is used to transmit five full channels. In addition, one channel is used

exclusively for low frequencies (effects). Speakers are positioned at front left, center, and front

right, as well as rear left and right. This system is currently the most common and is also used in

movie theaters.

This DVD recorder records each sound in two-channel Dolby Digital on a DVD+RW.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are

trademarks of Dolby Laboratories.

Transmission standard for 5.1 channels from Digital Theatre Systems, Inc. It is the second most

common after Dolby Digital.

This product incorporates copyright protection technology that is protected by US patent

numbers 4631603, 4577216 and 4819098, as well as other intellectual property rights. Use of

this copyright protection technology must be authorized by Macrovision Corporation, and is only

intended for home use and other pay-per-view applications. Macrovision must provide written

authorization for any other use. Changes to the device, reverse engineering, or disassembly is

prohibited.

Simple programming system for DVD recorders. Makes programming as easy as making a telephone

call. Simply enter the number code associated with your television program. This number is located

in your television listings magazine.

VCR Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The

VCR Plus+ system is manufactured under licence from Gemstar Development Corporation. US

patent no.: 5.307.173, 5.335.079, 4.908.713, 4.751.578 and 4.706.121

So that you can identify your machine for service questions or in the event of theft, enter the

serial number here. The serial number (PROD. NO.) is printed on the type plate fixed at the

rear of the recorder:

MODEL NO.

PROD. NO.

MDV630R/MDV650R

..................

Introduction

BConnecting the DVD recorder

Preparing the remote control for

operation

The remote control and its batteries are packed separately in the original DVD recorder

packaging. You must install the batteries in the remote control before use.

Take the remote control and the enclosed batteries (2 AA

batteries).

Remove the battery compartment lid, insert the batteries as

shown, then replace the battery compartment lid. Always install

the +/- ends of the batteries as indicated inside the battery

compartment.

The remote control is now ready to use.

Its range is approximately 16-32 feet (5 to 10 meters).

Aim correctly

In the following sections, you require the remote control for the first

time. When using, always aim the front of the remote control at the

DVD recorder, and not at the TV.

Tip

Connecting your DVD recorder to the TV

The necessary cable connections must be made before you can record or playback TV programs

using your DVD recorder.

Connect the DVD recorder directly to the TV. Connecting a video cassette recorder between

the DVD recorder and the TV could result in poor picture quality because of the copy

protection system built into the DVD recorder.

Connecting the DVD recorder

When you install your DVD recorder for the first time, select one of the following options:

'Connecting with Component Video (Y Cr Cb, YUV)

If your TV is equipped with Component Video (Y Cr Cb, YUV)

What is 'Component Video (Y PB PR)'?

It is a system for transmitting high-quality video by splitting the video

signal into the Y (brightness), U and V (red minus brightness, blue minus

brightness) components. The jacks for these cables are usually red,

green, and blue.

This connection provides a studio quality picture.

'Connecting with S@Video (Y/C)'

If your TV is equipped with a S-Video (SVHS) jack.

What is a 'S@Video (Y/C) cable'?

Also called a S-VHS cable, it is a video connection standard in which the

Y signal and the C signal are transmitted separately. This mini-din

jack/jack is also called a hosiden jack/jack.

'Connecting with a Video (CVBS) cable'

If your TV is equipped with a Video (CVBS) jack.

What is a 'Video (CVBS)' jack?

This typically yellow jack is used to transmit composite video signals

(FBAS, CVBS). This system transmits the Y and C signals over the same

line. In some cases, this can lead to picture distortions, or 'Moiré'.

'Connecting only with the antenna cable'

If you do not wish to use any other cable. You may use an antenna cable (RF coaxial) if you prefer

or if your TV has only an Antenna In jack (no other audio and video in jacks). The TV's Antenna In

jack may be labeled ANT IN, RF IN, 75 ohm, etc. Check your TV instructions for details.

Connecting the DVD recorder

Connecting with a Component Video

(Y Pb Pr) cable

Have the following cables ready:

an antenna cable (1 supplied), a power cable (2 supplied), a Component Video (Y PB PR) cable

(3, red, green, blue jack) or a corresponding video-compatible cinch cable, an audio cable (4

supplied red/white jack).

Remove the antenna or cable TV signal from your TV. Connect it

to the ANTENNA jack at the bck of the DVD recorder.

Insert one end of the supplied antena cable into the TV plug at

the back of the DVD recorder and the other end into the

antenna input jack at the back of the TV.

Use the Component Video (Y PB PR) cable and connect one end

to the red, blue, green OUT COMPONENT VIDEO jacks at the

back of the DVD recorder and the other end to the Component

Video In jacks of the TV.

Please note the color order

The colors of the jacks on the DVD recorder must match those on the

TV (red-red/blue-blue/green-green). If they are not matched properly,

this could cause the color of the picture to be reversed or there could

Tip

be no picture at all.

Use the supplied audio cable and plug one end into the OUT

AUDIO LR jack at the back of the DVD Recorder (next to

OUT COMPONENT VIDEO ) and the other into the red/white

Audio In jacks of the TV (usually called Audio in', 'AV in'. Please

see your TV's owner's manual).

Switch on the TV.

Set the TV to the Component Video channel

If necessary, see the operating instructions for your TV. Or, go

to channel zero on your TV, then keep changing channels down

until you see the DVD Recorder screens (when the Recorder is

on). This is not channel 3 or 4 as it would be if you used only

the cable/antenna connection.

Connecting the DVD recorder

Insert one end of the supplied power cable into the power outlet

4MAINS at the back of the DVD recorder and the other end

into the wall socket. 'IS TV ON?' will appear on the display.

Then, read 'Initial installation' in 'Installing your DVD recorder.'

Connecting with a S@Video (Y/C) cable

Have the following cables ready:

an antenna cable (1, supplied), a power cable (2, supplied), a S-video (SVHS) cable (3), an audio

cable (4, supplied red/white jack).

Remove the antenna cable plug from your TV. Insert it into the

ANTENNA jack at the back of the DVD recorder.

Insert one end of the supplied antenna cable into the TV jack at

the back of the DVD recorder and the other end into the

antenna input jack at the back of the TV.

Use a S-Video (SVHS) cable and plug one end into the OUT

S-VIDEO (Y/C) jack at the back of the DVD Recorder and the

other end into the S-Video (SVHS) In jack of the TV (usually

called S-Video in or SVHS in. Please see your TV's owner's

manual).

Use the supplied audio (cinch) cable and plug one end into the

red/white cinch jack OUT L AUDIO R at the back of the DVD

Recorder (next to OUT S-VIDEO (Y/C) ) and the other into

the corresponding red/white audio input of the TV (usually called

Audio in', 'AV in'-please see your TV's manual).

Switch on the TV. Then switch the set to the SVHS input jack or

select the corresponding channel number. You will find the

channel number in the operating instructions of your TV.

Connecting the DVD recorder

Insert one end of the supplied power cable into the power outlet

4MAINS at the back of the DVD recorder and the other end

into the wall jack.

A message, 'IS TV ON?' will appear on the Recorder's display to

remind you to set your TV to its Audio/Video In channel.

Then, read the paragraph 'Initial installation' in the chapter 'Installing your DVD recorder'.

Connecting with Video (CVBS)

Have the following cables ready:

an antenna cable, a power cable, a video (CVBS) cable (with yellow ends), and an audio cable

(with red/white ends).

Remove the antenna cable plug from your TV. Insert it into the

ANTENNA jack at the back of the DVD recorder.

Insert one end of the supplied antenna cable into the TV jack at

the back of the DVD recorder and the other end into the

antenna input jack at the back of the TV.

Use the supplied video (CVBS) cable and plug one end into the

yellow jack OUT VIDEO (CVBS) at the back of the DVD

Recorder and the other end into the Video In jack (usually

yellow) of the TV (usually called Video in or AV in. See your TV's

owner's manual).

Use the supplied audio (cinch) cable and plug one end into the

red/white cinch jack OUT L AUDIO R at the back of the DVD

Recorder (beneath IN VIDEO (CVBS) ) and the other into the

corresponding red/white audio input of the TV (usually called

'Audio in', 'AV in'-please see your TV's manual).

Switch on the TV. Switch the TV to the Video/Audio input jack

or select the corresponding channel. For the channel, please see

your TV's operating instructions.

Connecting the DVD recorder

Insert one end of the supplied power cable into the power outlet

4MAINS at the back of the DVD recorder and the other end

into the wall jack.

A message, 'IS TV ON?' will appear on the Recorder's display to

remind you to set your TV to its Audio/Video In channel.

Then, read the paragraph 'Initial installation' in the chapter 'Installing your DVD recorder'.

Connecting only with the antenna cable

USE THIS CONNECTION IF YOUR TV ONLY HAS A SINGLE ANTENNA IN JACK AND

DOES NOT HAVE ANY AUDIO/VIDEO JACKS.

Have the following cables ready:

an antenna cable (supplied), and a power cable (supplied).

Switch off your TV.

Remove the antenna or Cable TV signal from the antenna input

jack of the TV. Connect it to the ANTENNA jack at the back of

the DVD recorder.

Connect one end of the supplied antenna cable to the TV jack at

the back of the DVD recorder and connect the other end into

the antenna jack at the back of the TV.

Insert one end of the supplied power cable into the power outlet

4MAINS at the back of the DVD recorder and the other end

into the wall jack.

A message, 'IS TV ON?' will appear on the Recorder's display to

remind you to set your TV to its Audio/Video In channel.

Switch on your TV and select the channel used for DVD/VCR

playback on your TV. Choose between channel 3 or 4. Use your

TV remote to set the TV to 3 or 4.

Connecting the DVD recorder

How do I switch the Recorder between channel 3 and 4?

The factory setting is for channel 3. However, if you would like to

switch to channel 4, proceed as follows:

Press CHANNEL q while 'IS TV ON?' is displayed. 'C04' (channel

4) will appear on the display.

If you want to switch back to channel 3, press CHANNEL r .

'C03' (channel 3) will appear on the display.

Switch your TV to the selected channel (channel 3 or 4).

The menu for language selection will appear on the screen.

Initial Setup

aI don't see a menu for language selection

b Check the cable connections.

Menu Language

b Is 'DVDR' (DVD recorder operation) lit up in the display?

If not, press the TV/DVD button until 'DVDR' is lit.

English

Español

Français

Problem

b Change between channel 3 and 4 on the TV.

Press OK to continue

This TV channel number must be used in the future for DVD

recorder playback.

Then, read the paragraph 'Initial installation' in the chapter 'Installing your DVD recorder'.

Connecting the DVD recorder

CConnecting additional devices

You can connect additional devices such as decoders, satellite receivers, camcorders, etc. to the

IN S-VIDEO (Y/C) , IN VIDEO (CVBS) , IN COMPONENT VIDEO jacks on the recorder.

You will also use the AUDIO IN jacks of the Recorder for connecting to other devices.

Can I also connect devices with 'Progressive scan'?

The IN COMPONENT VIDEO jacks are only used for 'interlaced'

signals. Signals using progressive scan cannot be processed by the DVD

recorder.

Connecting an additional video recorder

You can also connect a video recorder to the input jack. Please use the IN S-VIDEO (Y/C) jack

and the IN L AUDIO R jacks for SVHS video recorders.

Please be aware

Most pre-recorded video cassettes and DVDs are copy protected. When you attempt to copy

them, the 'COPY PROT' message will appear in the DVD recorder display.

aWhen copying video cassettes 'NO SIGNAL' appears in the

DVD recorder display

b Check to make sure that the scart cable is inserted properly.

b If the recording is made from a video recorder, adjust the "tracking"

on the video recorder.

b The DVD recorder may sometimes not recognize video input signals

that are poor or non-standard.

aWhen copying from DVDs or pre@copied video cassettes, the

picture is grainy and the brightness fluctuates.

b This occurs when you attempt to copy copy-protected DVDs or

video cassettes. Although the picture on the TV is OK, the recording

is distorted on

cassettes cannot be copied without these disruptions.

DVD+R(W). Copy-protected DVDs and video

Problem

Connecting additional devices

Connecting a camcorder to the front jacks

The front video and audio jacks can be used to easily connect a camcorder to the DVD

recorder. These jacks are behind the door in the lower left corner of the front panel.

Very good Picture Quality

If you are using a Hi8 or S-VHS camcorder, connect the S-VIDEO IN jack of the DVD

recorder to the corresponding S-video out jack on the camcorder.

You must also connect the left AUDIO right In jacks of the DVD recorder to the audio out

jacks on the camcorder.

Good Picture Quality

If your camcorder only uses a video output (Composite Video or CVBS), connect the

VIDEO input of the DVD recorder to the corresponding Video Out jack on the camcorder.

You must also connect the left AUDIO right In jacks of the DVD recorder to the audio out

jacks on the camcorder.

Connecting audio devices to analog audio

jacks

There are Left/Right Audio Out jacks OUT L AUDIO R and two Left/Right Audio In jacks IN L

AUDIO R on the back of the DVD recorder.

These can be used to connect the following devices:

•) an receiver with Dolby Surround Pro Logic

•) a receiver with two@channel analog stereo

Can I use the 'Phono input' ofmy ampliifer?

This amplifier jack (input) should only be used for record players without

amplifiers. Do not use this input for connecting the DVD recorder.

This could damage the DVD recorder or the amplifier.

Connecting additional devices

Connecting audio devices to the digital

audio jack

The rear of the DVD recorder has a DIGITAL AUDIO OUT jack for a coaxial cable

connection.

It can be used to connect the following devices:

•) a Audio Video receiver or an Audio Video amplifier with a digital multi@channel

sound decoder

•) a receiver with two@channel digital stereo (PCM)

Digital multi@channel sound

Digital multi-channel sound provides maximum sound quality. It requires

a multi-channel Audio Video receiver or amplifier that supports at least

one of the DVD recorder's audio formats (MPEG2, Dolby Digital, or

DTS). Check your receiver's manual to see which format it supports.

aA loud distorted sound is coming from my speakers

b The receiver does not support the digital audio format of the DVD

recorder. The audio format of the inserted DVD is displayed in the

display panel when another language is switched on. Playback using

6-channel digital surround sound is only possible when the receiver

has a digital multi-channel sound decoder.

Problem

Connecting additional devices

DInstalling your DVD recorder

Initial installation

After you have successfully connected the DVD recorder and other devices to your TV (as

described in the previous chapter), this chapter will help you start the initial installation. The

DVD recorder automatically seeks and stores all available TV channels.

'Correct aiming' ofthe remote control

In the following sections, you require the remote control for the first

time. When using, always aim the front of the remote control at the

DVD recorder, not the TV.

Connecting additional devices

If you have connected additional devices (satellite receiver,...) via the

antenna cable, switch them on now. The automatic channel search will

recognize them and save them.

No antenna connected

If you are only using the DVD recorder as a playback device or you only

have a satellite receiver connected, you still need to perform the initial

installation. This is necessary so the basic settings can be saved correctly.

After the initial installation is completed once, you can used the DVD

Tip

recorder normally.

Select the desired language for the on-screen menu by pressing

B or A .

Initial Setup

Menu Language

What is an on@screen menu?

English

Español

Français

The multi-language on-screen menu takes the mystery out of using your

new DVD recorder. All settings and/or functions are displayed on your

TV screen in one of the available languages (English, French, or Spanish).

Press OK to continue

Confirm by pressing OK .

Select the desired audio language using B or A .

Initial Setup

What is the audio language?

Audio Language

English

Español

Français

Português

Italiano

The DVD audio will play in the selected language if it is available. If this

language is not available on the DVD, the audio will play in the first

language on the DVD. The DVD disc menu will appear in the selected

language if it is available on the disc.

Press OK to continue

Confirm by pressing OK .

Installing your DVD recorder

Select the desired language for the subtitles by pressing B or

A .

Initial Setup

Subtitle Language

English

Español

Français

Português

What is the language ofthe subtitles?

DVD subtitles will be in the selected language if it is available. If this

language is not available, subtitles will be in the first language on the

DVD.

Italiano

Press OK to continue

Confirm by pressing OK .

Select the desired screen format with B or A . This setting

only functions if you have inserted a DVD recorded in this

format.

Initial Setup

TV Shape

4:3 letterbox

4:3 panscan

16:9

Which screen formats can I choose?

4:3 letterbox for a wide-screen display (theatrical format) with black

bars at the top and bottom of the picture.

Press OK to continue

4:3 panscan

16:9

for a full-height picture with the sides trimmed to fill you

TV screen.

for wide-screen TV (16:9) aspect ratio

Confirm by pressing OK .

After you connect the antenna (or cable TV signal, satellite

receiver, etc.) to the DVD recorder, press OK

Make sure the Cable TV signal is connected securely to the

Antenna jack on the rear of the DVD Recorder.

The automatic TV channel search starts. 'WAIT' will appear on the

display.

Installation

aDuring the channel search, ifthe DVD recorder does not ifnd

any TV channels:

Auto Ch. Programming

Searching for TV channels

000 Channels found

b Select another channel on the TV. Do you see that channel on the TV

set?

If not, check the connections between the DVD recorder and the TV.

b Please have patience.

The DVD recorder searches the entire frequency range in order to

find and save the largest possible number of TV channels. It is possible

that the TV channels in your country are broadcast in a higher

frequency range. As soon as this range is reached during the search,

the DVD recorder will find the TV channels.

Please wait

b If no antenna is connected, complete the basic settings and then, if

desired, start the automatic channel search (see section 'Automatic TV

channel search').

aThe DVD recorder finds very few/no channels during the

search.

b It is possible that the automatic switching between antenna/cable does

not properly detect your TV signal. Read the section about how to

switch manually.

Problem

Installing your DVD recorder

Wait until all available TV channels have been found. This can

take several minutes.

As soon as the automatic TV channel search is completed, 'Auto

ch. search complete' will appear on the TV screen along with

the number of channels found.

To remove the menus, press the SYSTEM-MENU button on

the Recorder's remote control.

The initial installation is now complete.

Automatic TV channel search

During installation, all available TV channels are searched for and saved. If the channel

assignments of your cable or satellite TV provider change or if you are reinstalling the DVD

recorder, e.g. after moving, you can start this procedure again. This will replace the TV channels

already saved with the new ones.

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or the Audio/Video In channel).

Turn on the DVD recorder by pressing STANDBY/ON .

Press SYSTEM-MENU on the remote control. The menu bar

will appear at the top of the TV screen.

Select ' ' using D or C .

Press B continuously to select the line 'Installation'. (It is on

the second screen of menus.) Confirm with C .

Select line 'Auto Ch. Programming' using B or A .

Press C . The automatic TV channel search starts. This allows

the DVD recorder to save all available TV channels. This

procedure may take several minutes.

When the channel search is completed, 'Auto ch. search

Installation

Auto Ch. Programming

complete' will appear on the TV screen.

Searching for TV channels

000 Channels found

Press SYSTEM-MENU repeatedly to remove all the menus

from the screen.

Please wait

Installing your DVD recorder

aVery few TV channels were found

b During 'Automatic channel search' the DVD recorder detects whether

an antenna or a cable TV signal is connected. If you have connected a

cable TV signal but found very few TV channels, you must search the

channels manually.

To do so, select 'Cable/Antenna' insted of line 'Auto Ch.

Programming' in step 6 and confirm with C .

If you select 'Cable', channels 1-125 will be available. If you select

'Anten.', channels 2-69 will be available. Select your type of

connection by pressing C repeatedly

'Anten.', 'Cable' or Auto.' automatically detects which one you have.

Confirm the setting with OK .

Press SYSTEM-MENU to go to the next menu. Press OK to start

channel search as prompted by the on-screen message. When the

channel search is complete, press SYSTEM-MENU repeatedly to

remove all the menus.

Problem

You can read about how to search for a TV channel manually in the following section 'Adding

and clearing TV channels manually'.

Adding and deleting TV channels manually

Turn on your TV. If required, select the TV's Audio/Video In (or

channel 3 or 4).

Press STANDBY m to turn on the DVD recorder. Press the

SYSTEM-MENU button on the remote control. The menu bar

will appear on the TV screen.

Select ' ' using D or C .

Press B repeatedly B to select 'Installation' and then press

C .

Select line 'Add/Delete Channels' using B or A then press

C .

Using B or A select the TV channel that you want to delete

or add.

Installation

Add/Delete Channels

...

•

Channel 001

Channel 002

Channel 003

Channel 004Delete

Channel 005

Channel 006

...

Add

Press C or D to choose 'Add' or 'Delete'.

Add

Delete

Repeat steps 6 to 7 until you have added/deleted all the TV

channels you want.

To exit press

SYSTEM MENU

To save your channel selections, press OK .

Installing your DVD recorder

To remove the menus, press SYSTEM-MENU repeatedly.

Setting the language

You can select the language for subtitles and audio for DVD playback. Please observe that with

some DVDs, you can change the audio language and/or subtitle language only via the DVD disc

menu.

Moreover, when recording the sound of a TV channel, you can switch between stereo and an

additional language (SAP - Secondary Audio Program). See the following section on Switching

audio recording (stereo, SAP).

Plus, you have the option of setting one of the displayed languages for the Recorder's on-screen

menu. However, the DVD recorder will only display show text regardless of this setting.

Switch on the TV and, if required, select the channel number for

the DVD recorder (channel 3 or 4 or Audio/Video In).

Turn on the DVD recorder by pressing STANDBY/ON .

Press SYSTEM-MENU on the remote control. The menu bar

will appear in the display.

Select ' ' using D or C .

Select the line 'Language' using B or A then press C .

Select the corresponding line and confirm with C .

Language

Which settings can I choose?

Playback audio

Recording audio

Subtitle

English

Stereo

English

Playback audio: language for playback (audio language)

Recording audio: type of audio recording 'Stereo' or 'SAP'

Subtitle: subtitle language

Tip

Menu: language of the Recorder's menu

Select the corresponding setting with B or A and confirm with

OK .

To end, press SYSTEM-MENU .

Installing your DVD recorder

Switching audio recording (stereo, SAP)

Some TV programs broadcast additional audio (SAP - Secondary Audio Program). In most cases

this means an additional language is available. For example, if a program is available in English and

Spanish, Spanish can be broadcast as the additional audio program (SAP).

In order to record TV programs in stereo or SAP, you can select stereo or SAP as a default

setting. This setting will only become active when the sound of a TV program is broadcast in

stereo or SAP.

When you playback the recording, you can playback the sound only in the setting you selected

for recording (a recording in SAP can be played back only in SAP).

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or Audio/Video In).

Switch on the DVD recorder with STANDBY/ON .

Press SYSTEM-MENU on the remote control. The menu bar

will appear in the display.

Select ' ' using D or C .

Select the line 'Language' using B or A and confirm with

C .

Select 'Recording audio' and press C .

Language

Select 'Stereo' or 'SAP' using B or A and confirm with OK .

Playback audio

Recording audio

Subtitle

English

Stereo

English

A TV program is only available in 'Stereo' but my setting is

'SAP'?

If the setting for 'Recording audio' is 'SAP' but the TV channel

broadcasts only in stereo during recording, the recording will be done in

stereo.

To end, press SYSTEM-MENU .

Installing your DVD recorder

VCR Plus+^®Guide channel numbers

If you intend to use the VCR+^®programming system, you must first assign channel numbers to

Guide channel numbers.

Press SYSTEM-MENU on the remote control. The menu bar

will appear in the display.

Select ' ' using D or C .

Select line 'Installation' using B or A and confirm with C .

Select the line 'VCR Plus+ Ch.' using B or A and confirm

with C .

Use B or A to select the Guide channel number you want to

assign to a channel number.

Installation

VCR Plus+ Ch.

Channel

Use D or C , or use the number buttons 0..9 to select the

channel corresponding to this Guide channel number. An

overview of guide numbers/TV channels can be found in your

...

001

002

003

004---

005

...

---

daily newspaper or in your TV listings.

---

Confirm the allocation with OK .

To exit press

SYSTEM MENU

To end, press SYSTEM-MENU .

Installing your DVD recorder

Setting the time/date automatically

This function uses the information sent via the local PBS channel to automatically set the

time/date. For this reason, you must enter the PBS channel that sends this additional information.

When the DVD recorder chooses a wrong PBS channel or the displayed time/date is wrong, you

must manually set the date/time (see section 'Manually setting the time & date').

Press SYSTEM-MENU on the remote control. The menu bar

will appear in the display.

Select ' ' using D or C .

Select line 'Time/Date' using B or A and confirm with C .

Select 'Automatic' with B or A and confirm with C .

Select the corresponding line with B or A .

Time/Date

Automatic

PBS Channel

Daylight Saving

Time Zone

Auto.

Select the channel which sends the time/date information in the

line 'PBS Channel' and confirm with OK . The DVD recorder

will check whether or not the information transfer is possible.

a'' will appear on the TV screen

To exit press

b No time/date data can be received from this TV channel.

SYSTEM MENU

Problem

Select a different channel or 'Auto.' in line 'PBS Channel'.

Select how switching will be done in line 'Daylight Saving':

('Auto./Yes/No').

By selecting 'Auto.', the time will be automatically set according

to the 'summer time' schedule of the PBS channel.

In the line 'Time Zone', select your time zone if the PBS channel

entered was for a different time zone. This is the only way to set

the time correctly, or, if necessary, to correct it.

If you want to use the time zone of the PBS channel, select

'Auto.'.

Confirm each line with OK .

To end, press SYSTEM-MENU .

The time and date are automatically transferred from the selected 'PBS channel' after the

recorder is shut off.

Installing your DVD recorder

Manually setting the time & date

If the time is incorrect, this could be due to a weak or disrupted TV signal. If this is the case,

switch off the automatic function.

Press SYSTEM-MENU on the remote control. The menu bar

will appear in the display.

Select ' ' using D or C .

Select line 'Time/Date' using B or A and confirm with C .

Select 'Manual' with B or A .

Confirm with OK .

Change the time in line 'Time' using the number buttons 0..9 on

your remote control.

Time/Date

Manual

Time

09:02

2002

Check 'AM/PM', 'Year', 'Month', and 'Date' in the same way. To

select between the fields, use B or A .

Change the information with D , C or the number buttons

AM/PM

Year

Month

Date

Daylight Saving

0..9 .

Select one of the following settings in line 'Daylight Saving':

To exit press

SYSTEM MENU

'Yes': The time set corresponds to the summer time (summer

time is on)

'No': The time set corresponds to the winter time (summer time

is off)

When all settings are correct, confirm with OK .

To end, press SYSTEM-MENU .

Installing your DVD recorder

EInformation on the TV screen

You can check/change many functions and settings of your DVD recorder via the system menu

bar. The menu bar cannot be displayed during recording.

Menu bar icons

The SYSTEM-MENU button is used to call up the menu bar (main menu) and to remove it.

The D and C buttons are used to select the corresponding function. The B button confirms

the function and either leads you to an additional menu or it executes the function.

Depending on the disc inserted, several functions may not be available.

Menu bar 1

User preferences

Current Title/Track

Current Chapter/Index

Audio Language

Subtitle Language

Camera Angle

Zoom

Menu bar 2

While menu bar 1 is being displayed, you can press C repeatedly to display menu bar 2.

Sound

Picture by Picture

Slow motion

Fast motion

Search with time entry

Information on the TV screen

Field for temporary messages

There is a field in the top left corner of the menu bar which displays temporary information

regarding different operating functions. This information appears briefly on the screen when

certain disc functions are activated.

Shuffle: Shuffle tracks

Scan: Play introduction to each track

Repeat entire disc

Repeat current title

Repeat current track

Repeat current chapter

Repeat A until end

Repeat A to B

Camera Angle

Child lock on

Resume

Action prohibited

Status box

The status box displays the current status of the DVD recorder and the type of disc inserted.

This display can be turned off.

Disc type icons

DVD+RW

DVD+R

DVD@Video

Video@CD

No disc

Disc error

Information on the TV screen

Disc status icons

Recording

Stop

Playing

Pause play

Pause record

Fast forward (x4)

Fast reverse (x4)

Slow motion

Tuner info box

This box appears in the bottom left corner of the TV screen. It displays the current antenna

signal and TV channel.

Current channel / selected device

No Signal

TV channel is not available or reception to too weak / Device is not

connected or is turned off

Copy@protected signal

Timer info box

This box is located above the tuner info box. When a recording is programmed (timer), it shows

the start time or date of the first recording.

When no timer is programmed, the current time will be displayed.

This box is not displayed during disc playback or recording. However, you can access it during

an OTR by pressing SYSTEM-MENU .

Timer set for day shown or time shown (if set for today).

OTR recording will run until displayed stop time

Current time

No recording (timer) programmed

Information on the TV screen

FPlayback

General information regarding playback

The DVD recorder can be used with the following systems:

•) DVD Video

•) Video CD or Super Video CD

•) DVD+RW

•) DVD+R

•) DVD-RW (video mode, finalized)

•) DVD-R

•) CD-R

•) CD-RW

•) Audio CD

•) MP3-CD

You can operate the DVD recorder using the remote control or the buttons on the front of the

DVD recorder.

Inserting a disc

Press the OPEN/CLOSE button on the front of the Recorder.

The disc tray will open. 'OPENING' will appear in the display, then

'TRAY OPEN.'

OPENING

C01

Carefully place the disc into the tray with the label facing up, then

press PLAY/PAUSE G9 or OPEN/CLOSE . 'CLOSING' then

'READING' will appear on the display. This indicates the disc is

being read.

How do I insert double@sided DVDs?

Double-sided DVDs do not have labels on either side. The label for each

side is placed in the middle (on the inner ring). To play a specific side,

the label on the side you want to play must be on top.

Opening/Closing the tray using the remote control

You can also use the remote control to open and close the disc tray.

To do this, hold down the STOP h button on the remote control until

'OPENING' (opens) or 'CLOSING' (closes) appears in the display.

Tip

Playback may begin automatically.

A menu may appear during playback of a DVD. If the titles and chapters are numbered, press a

number button on the remote control. You can also select a menu item with D , C , A ,

B and confirm with OK .

Playback

When playing a DVD+RW, the Index Picture screen appears. Choose the title you want to play

with B , or A .

Confirm with OK .

For more information, read 'Playing a DVD+RW or DVD+R'.

If Audio/CD playback does not begin automatically, press PLAY/PAUSE G9 .

For more information, read 'Playing Audio CDs'.

If 'h' is displayed during Video CD playback, begin replay with PLAY/PAUSE G9 .

If a menu appears on the screen, select the corresponding menu item with the buttons of the

remote control indicated on the screen (PREV= N , NEXT= O ) or with the remote control

buttons 0..9 .

For more information, read paragraph 'Playing Video CDs'.

Playing a DVD

a'PIN' may appear on the display.

b The child lock was activated for the inserted disc. Read 'Child lock'

and 'Authorizing discs' in the 'Child lock' chapter.

aI see an 'X' in the menu bar on the screen.

b DVDs can be manufactured in such a way that certain operations are

required or only specific functions are possible during playback. When

the 'X' symbol appears on the screen, the selected function is not

available.

aI see region code information on the screen.

b Because DVD films are usually not released at the same time in all

regions of the world, all DVD players are keyed to a specific region

code. Discs can be assigned an optional region code. If the region

codes of the player and disc do not coincide, playback is not possible.

b The region code for a DVD player can be found on a label at the

back of the device.

b There are no region codes for DVD+Rs or DVD+RWs.

aI am asked to select an option from a menu.

b Using A , B , D , C or the number buttons 0..9 select the

corresponding option.

In some cases, you will need to confirm with OK .

You can always call up the disc menu with the DISC-MENU button

on the remote control.

Problem

Playback

How can I display disc information?

Press the DISC-MENU button on the remote control. A menu

will appear on the screen. Some films may show

introductory sequence before displaying the menu.

short

Using A , B , D , C or the number buttons 0..9 select the

corresponding option.

Tip

Confirm with OK .

PLAY/PAUSE G9 .

This will appear on the display: title, chapter, elapsed time.

playback

does

not

start

automatically,

press

2:04

To stop playback, press STOP h on the remote control or

hSTOP on the DVD recorder.

To eject the disc, press OPEN/CLOSE on the front of the

DVD recorder.

Playing a DVD+RW or DVD+R

If the inserted disc has been write-protected or it is a finalized,

DVD+R, playback starts automatically.

If playback does not start automatically, select the title you want

from the index screen using B or A .

You can also use the N or O buttons on the front of the

Recorder to select a title.

2 ANNA

C01

Press the PLAY/PAUSE G9 button.

This will appear on the display: Title number, recording mode,

elapsed playing time.

aI see the message 'EMPTYDISC' on the display

Problem

b There are no recordings on this disc.

To stop playback, press STOP h on the remote control or

hSTOP on the DVD recorder.

Playback

To eject the disc, press OPEN/CLOSE on the front of the

DVD recorder.

When I play recordings that have been recorded in different

recording modes, do I have to change each manually?

During playback, the device will automatically switch to the proper mode

'HQ(HQ), SP+(SP+), EP(EP), EP+(EP+)'.

For more information, please read the section 'Selecting the recording

mode (quality)' in the chapter 'Manual recording'.

Playing audio CDs

You can also use the DVD recorder to pay audio CDs

Insert an audio CD. Playback starts automatically.

Audio CD display

If the TV is turned on, the Audio CD display will appear on the screen.

During playback, the number of the current track will be shown on the

screen and display.

Tip

Stop playback with STOP h . Track number and total play time

are displayed.

Playing MP3 CDs

MP3 (MPEG1 Audio Layer-3) files are highly compressed pieces of music. This enables you to fit

up to 10 hours of CD quality music on a single CD-ROM.

When creating MP3 CDs, keep the following in mind:

Data system supported: ISO9660, Joliet

Format supported: *.mp3

File names 6a ASCII characters max. (Joliet)

Maximum of 99 albums, 999 titles

Sampling frequency supported: 44.1kHz, 48kHz. Music pieces with different frequencies will be

skipped.

Bit rate supported: 32, 64, 96, 128, 192, 256 (kbps)

ID3 Tag: Version 1, 1.1. In the case of later versions, the directory name will appear as the

album and the file name as the title.

Insert a MP3 CD. Playback starts automatically. (See additional

instructions on the next page.)

Playback

MP3 CD display

If the TV is turned on, the MP3 CD display will appear on the TV

screen.

During playback, the number of the current track will be shown on the

screen and display.

During interrupted playback, the number of albums will be shown on the

TV and on the CD's display.

Tip

If availableon the CD, album, track, and artist may appear on the display.

Stop playback with STOP h . The number of albums appears on

the display.

Other playback functions

Select the beginning of the current track or the previous or next track

with N or O .

You can also use T/C to select tracks and albums.

Press T/C and then select symbol 'T' for album or 'C' for track

with C or D .

Select the number of the album/track with B , A or the number

buttons 0..9 on the remote control.

Tip

You can also use repeat functions ( PLAY MODE ).

Playback ofa (Super) Video CD

(Super) Video CDs may feature 'PBC' (Play Back Control). This allows the direct selection of

special playback functions (menus). The Video CD must be PBC-compatible (see CD packaging).

'PBC' is turned on by default.

Insert a (Super) Video CD.

If the 'h' appears on the display, begin playback with

PLAY/PAUSE G9 .

If a menu appears on the screen, select the corresponding menu

item with the buttons of the remote control indicated on the

screen (PREV= N , NEXT= O ) or with the remote control

buttons 0..9 . Using the buttons, select the corresponding menu

item until playback starts.

If the PBC menu contains a title list, the desired title can be

chosen directly.

The RETURN button will take you back to the previous menu.

Stop playback with STOP h .

Playback

GOther playback functions

Changing to a different chapter track/title

When a disc contains more than one track, title, or chapter, you can change to a different track,

title or chapter as follows. However, if a title contains several chapters, these are selected. Title

selection is then possible via the menu bar only.

During playback, you can go to the next title/chapter/track using

the O button. Using the N button, you can return to the

start of the current title/chapter/track. Using the N button,

you can return to the start or the previous title/chapter/track.

Using the T/C (title/chapter) button

Press the T/C (title/chapter) button and select the corresponding

title with A or B .

Make sure that the 'T' (title) icon is selected in the menu bar.

You can also select a chapter within a title using the T/C button.

Press T/C and select 'C' (chapter) using C .

Then select the corresponding chapter with A or B .

Tip

Disc search

You can fast forward a disc at four or 32 times normal playback speed. You can select other

speeds only via the menu bar ( ).

During playback, hold down N (reverse) or O (forward) to

switch to the search function. You can switch between different

speed modes using the N / O buttons.

To continue playback, press PLAY/PAUSE G9 twice at the

desired position.

aNo sound

b During search the sound is turned off. This is not a fault in your

machine.

Problem

Search function via menu bar

Press SYSTEM-MENU on the remote control during playback.

The menu bar appears at the top of the screen.

Select the '

D and confirm with B .

' symbol on the second menu bar using C or

Now you can select different search speeds forwards or backwards

using D or C .

If necessary, switch off the menu bar using SYSTEM-MENU .

To resume playback, press PLAY/PAUSE G9 twice.

Tip

Other playback functions

Still picture

During playback, press PLAY/PAUSE G9 to stop playback and

display a still picture.

2:04

Still picture features via the menu bar

While playback is paused, press the SYSTEM-MENU button on

the remote control. The menu bar will appear at the top of the

screen.

Select '

B .

' in the second menu bar with C or D then press

You can now move the still picture forward or backward using

D or C .

necessary,

remove

the

bar

with

the

SYSTEM-MENU button.

Tip

To continue playback, press PLAY/PAUSE G9 .

Slow motion

Press PLAY/PAUSE G9 on the remote control during

playback. Then hold down N or O to switch to slow

motion.

You can switch between the different speeds with N or O .

Slow motion via menu bar

During playback, press the PLAY/PAUSE G9 button and then

the SYSTEM-MENU button on the remote control. The menu

bar will appear at the top of the screen.

Select ' ' with C or D and confirm with B .

You can now move forwards or backwards at different speeds using

D or C .

necessary,

turn

off

the

line

with

the

SYSTEM-MENU button.

Tip

To continue playback, press PLAY/PAUSE G9 twice.

Other playback functions

Search with time entry

Using this function, you can start playing a disc at a specific time.

During playback, press the SYSTEM-MENU button on the

remote control. The menu bar will appear at the top of the

screen.

Select ' ' with C or D and confirm with B . The playback is

stopped and the screen displays how much play time has already

expired (playback time).

Enter the desired start time for the playback using the number

buttons 0..9 .

Confirm with OK .

aThe time that I entered is blinking on the screen

b The selected title is shorter than the time entered. Enter a new time

or cancel the function with SYSTEM-MENU .

Problem

Playback will now start at the time you entered.

Repeating/Shuffle

You can select an entire section or the entire disc for repeat playback. Depending on the disc

type (DVD-Video, DVD+RW, Video-CDs), you can select chapters, titles or the entire disc.

Select the desired chapter, title or disc and start playback.

During playback, press PLAY MODE . By pressing PLAY

MODE again, you can select from the following options:

•) '

': Repeat chapter (DVD only)

': Repeat track/title

': Repeat entire disc (video CD, audio CD only)

Shuffle

•) No display: no repeat

To cancel the repeat, press STOP h .

You can also keep pressing PLAY MODE until the displays

disappear.

Other playback functions

Repeat a specific segment A@B

You can repeat a specific segment within a title/chapter/track. To do this, you must mark the

start and end of the desired segment.

During playback, press the PLAY/PAUSE G9 at the desired

starting position. sYou will see a still picture.

Keep pressing PLAY MODE until the '

on the TV screen. This will store the start point.

' symbol appears

Start playback with PLAY/PAUSE G9 .

At the desired stop point, press the OK button. '

on the TV screen. Playback will now resume repeating the

selected segment.

' appears

To cancel the repeat, press STOP h .

You can also keep pressing PLAY MODE until the displays

disappear.

Scan function

Using this function, you can play the first 10 seconds of each chapter (DVD) or track (CD or

VCD) on the disc.

During playback, press PLAY MODE repeatedly until '

appears on the screen.

After 10 seconds, the DVD recorder will switch to the next

chapter/track. To resume the playback at the corresponding

chapter/track, press STOP h and then PLAY/PAUSE G9 .

Other playback functions

Zoom function

Using this function, you can enlarge the video image and pan through the enlarged image.

During playback, press PLAY/PAUSE G9 . You will see a still

picture.

Press the SYSTEM-MENU button and select ' ' using C .

Use B or A to select the desired zoom factor.

As soon as 'press OK to pan' appears, the zoom process is

complete.

Press OK . Use A , B , C , and D to select an area of the

image that you want to look at more closely.

Confirm with OK .

To stop zooming, press

SYSTEM-MENU .

PLAY/PAUSE G9 and then

Camera angle

If a disc contains video sequences that were recorded with different camera angles, you can

select different angles for playback.

During playback, press PLAY/PAUSE G9 . You will see a still

picture.

Press the SYSTEM-MENU button and select ' ' using C .

aThe '

' icon cannot be selected.

b The selected scene was only recorded with one camera angle. This

function is, therefore, not available. For more information, please read

the label of your DVD.

Problem

Select the desired angle with B or A . You can also directly

enter the angle number with the number buttons 0..9 .

After a short pause, playback will resume from the new angle.

The ' ' icon will remain visible until a section starts that only

has one camera angle.

Other playback functions

Changing audio language

DVDs sometimes come in different languages. The language used for playback is the one that you

selected during initial installation of the Recorder or the default language of the DVD. However,

you can change the audio language of a disc at any time.

Please note that the audio language can be changed via the menu ( DISC-MENU button) of the

inserted disc as well as via the Recorder's menu bar ( SYSTEM-MENU button). It is possible

for the audio languages of the two menus to be different. Some DVD's only allow you to change

the language in the DVD menu.

Press the SYSTEM-MENU button during playback and select

' using C .

Use B or A to select the desired audio language. You can also

directly enter the number with the number buttons 0..9 .

Playback will now resume with the new audio language.

Subtitles

DVDs sometimes come with different subtitle languages. The language used for playback is the

one that you selected during the initial installation or the default of the DVD. However, you can

change the subtitle language of a disc at any time.

Please note that the subtitle language can be changed via the menu ( DISC-MENU button) of the

inserted disc as well as via the Recorder's menu bar ( SYSTEM-MENU button). It is possible

for the subtitle languages of the two menus to be different.

Press the SYSTEM-MENU button during playback and select

' using C .

Select the desired subtitle language using the B or A . You can

also directly enter the number with the number buttons 0..9 .

You can shut the subtitles off with Number button s 0 or by

selecting 'off'.

Playback will now resume with the new subtitle language.

Other playback functions

HRecording

General information

What kind ofdiscs can be used of r recording?

You can used two different types of DVDs with this DVD recorder:

DVD+RW

This disc can be recorded on and then erased.

DVD+R

This disc can only be recorded on once.

For this DVD to be played in a DVD player, it must be finalized. After

this is done, no more recordings can be added to this disc.

If this disc is only to be played in the DVD recorder, then it does not

have to be finalized. Recordings can be added and then deleted.

However, the location (playing time) of the deleted recording (title) will

no longer be available. See page 55 for details on finalizing discs.

You can make a spontaneous recording (for example, a program currently being shown) by

following the steps.

To do this, select the title to be overwritten or choose an 'Empty title' in the 'index screen'

with the B , A buttons.

If the recording is to be inserted between existing recordings, please note the length of the old

and new recording. If the new recording is too long, the recording (title/chapter) following it will

be overwritten.

Adding new recordings after the end of all recordings (Safe

Record)

To add a new recording after the last recording on a disc, press and

hold the REC/OTR n button until 'SAFE REC' appears in the display.

For DVD+R, each new recording is always placed after all previous

recordings since previous recordings cannot be overwritten.

Tip

If you want to start and stop a recording manually, read the section 'Recording without

automatic switch@off'.

Please refer to 'Recording with automatic switch@off', if you want to start a recording

manually and conclude it within a specific amount of time. This permits accidentally recording to

the end of the disc.

Tip: If the end of a disc is reached during recording, recording will stop and the Recorder will

turn itself off automatically.

Recording

Recording without automatic switch@off

Switch on the TV and, if required, select the channel number for

the DVD recorder (channel 3 or 4 or Audio In channel).

Insert a disc to be used for the recording. The system and

content of the disc will be checked. 'READING' will appear on the

display.

aIndex display

b A DVD+RW was inserted that already contains recordings. Use

A and B to select

location where the recording should be

started.

a'EMPTYDISC' appears in the display.

b The inserted DVD is empty.

aA dialog box appears asking ifthe contents should be erased

or the disc should be ejected.

b The inserted disc is a DVD+RW whose contents are not compatible

with DVD Video (e.g. a data disc). This disc cannot be used for

recordings until the entire disc is erased using the

REC/OTR n button.

a'Too many titles' appears on the screen when a recording is

attempted.

b A disc can only contain a max. of 48 titles (including the empty titles).

Erase the titles or change the disc.

Problem

If necessary, switch to TV programming by pressing the

MONITOR button on the remote.

Use CHANNEL q or CHANNEL r to select the channel

(station name) you want to record. This will appear on the

display:

1 FREETITLE C01

Channel number ofthe external inputs:

'EXT2' SVHS jack (Y/C) IN S-VIDEO (Y/C) Video jack (CVBS) IN

VIDEO (CVBS) . Audio jack IN L AUDIO R for SVHS-jack

and Video jack.

Switching between jack IN S-VIDEO (Y/C) and IN VIDEO

(CVBS) is done automatically. In case both jacks are occupied,

the signal at jack IN S-VIDEO (Y/C) is given priority.

'EXT1' Component Video jacks on the back IN COMPONENT

VIDEO . Audio jacks IN AUDIO L R for Component Video

'CAM1' SVHS-/Audio front jacks S-VIDEO / left AUDIO right

'CAM1' Video/Audio front jacks A/V VIDEO / left AUDIO right

Switching between jack S-VIDEO and VIDEO is done

automatically. In case both jacks are occupied, the signal at jack

S-VIDEO is given priority.

Tip

Recording

To start recording, press REC/OTR n on the remote control

or RECORD on the DVD recorder. To start the recording after

all other recordings on the disc, press and hold the

REC/OTR n button until 'SAFE REC' appears in the display.

For DVD+Rs, each recording is always started after all previous

recordings since previous recordings cannot be overwritten.

The display panel will appear similar to the example shown at

right.

1 1:16:51 C01

Inserting chapter markers

During recording, scenes can be marked so they can be found or hidden

later.

During recording, press EDIT at the desired location. 'Inserting

marker' appears on the TV screen. In the display, the number of

'CHAPTERS' is increased by one.

For more information about title/chapter, please read the section

'Changing to a different title/chapter' in the chapter 'Playback'.

Tip

You can stop recording by pressing STOP h on the remote or

hSTOP on the recorder. 'MENU UPDT' will appear on the

display. The DVD recorder is preparing the list of contents. Wait

until this message disappears in the display, then the recording is

completed.

aIfdisplay reads ' DISC ERR'

b The recording could not be completed correctly because of a disc

error. Check and clean the inserted disc if necessary.

Problem

Making recordings on DVD+R discs compatible

If you want to playback recordings on a DVD player, you must first

finalize the disc in the DVD recorder. You can use the 'Finalizing'

function on the DVD so that it can be read by the DVD player without

problem. Please read paragraph 'Finalizing DVD+R discs' in the chapter

'Managing disc content'.

Tip

Recording

Pausing recording

During recording, press the PLAY/PAUSE G9 button.

To continue recording, press REC/OTR n .

Ending recording

To stop recording, press the STOP h button. Wait until 'MENU UPDT'

disappears from the display before you try another feature.

Tip

Recording with automatic switch@off

(OTR one@touch@recording)

Insert a disc.

Use CHANNEL q or CHANNEL r to select the channel you

want to record.

Press REC/OTR n on the remote control repeatedly . Each

time you press REC/OTR n you will add 30 minutes to the

recording time.

To check the remaining recording time while an OTR is in

progress, press SYSTEM MENU. The time at which the recording

will end will appear on the TV screen in the timer info box. To

stop an OTR, press STOP h .

How can I delete the recording time I just entered?

To delete an entry, press CLEAR while the display shows the recording

time.

Recording

Preventing accidental erasing ofdiscs

You can lock the entire disc to prevent important recordings from being erased by accident. You

can only lock the entire disc. It is not possible to lock individual recordings.

What happens with DVD+R discs?

As long as these discs have not been finalized, you can protect them

against being overwritten just like DVD+RW.

Put the disc to be locked into the recorder.

Press DISC-MENU to see the Index Picture Screen if necessary.

While the Index Picture Screen is displayed, press STOP h on

the remote control. The first title is selected.

Press A . The disc information screen is displayed.

Press the C button.

Select the line Protection with the up or down arrow.

Confirm with C .

Select 'Protected' using B and confirm with OK .

Press D , then press DISC-MENU to play the disc.

The entire disc is now protected. If you attempt a recording, 'DISC LOCK' will appear on the

display and 'Disc locked' will appear on the TV screen.

Tip: If you later decide to record on the disc, follow these steps but select Unprotected at step

Recording

Lining up recordings within a title

(assemble cut)

You can add further recordings to a title already contained on a DVD+RW. The new recording

will be added to the title as a chapter. Previous information will be overwritten from this

location onward. Depending on the length of the recording, this will also overwrite titles that

follow the current title. The recording mode (quality) is automatically transferred from the

current title.

To play back this recording, press SYSTEM-MENU and select 'C' (chapter) using C . You can

also use T/C .

For more information, read section 'Changing to a different title/chapter' in chapter 'Playback'.

What happens with DVD+Rs?

New recordings on DVD+R can only be made on existing space. You

cannot overwrite existing recordings on 'DVD+R' discs.

Find the title in which the new recording is to be inserted.

Look at the last minute of the old recording.

Press PLAY/PAUSE G9 on the remote control at the location

where the new recording is to start. '9' will appear on the TV

screen.

If you want to monitor the recording, you can switch to the

internal tuner using the MONITOR button.

Now start recording as usual by pressing REC/OTR n on the

remote control.

The new recording is added.

Stop recording with STOP h .

Recording

Selecting the recording mode (quality)

By selecting a recording mode, you define the picture quality of recordings and the maximum

recording time for a disc.

You can check the quality by switching to a recording mode watching the picture via the built-in

tuner. (Press the MONITOR button).

For playback, the correct picture quality will automatically be selected.

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or the Audio/Video In channel).

On the front of the DVD recorder, select the desired recording

mode using the REC MODE button.

You can also use the REC. MODE button on the remote

control.

Which recording modes can I choose?

'HQ/HQ': HighQuality offers the best picture quality with

total

recording time of 60 minutes.

'SP+/SP+': StandardPlay (better than S-VHS picture quality) offers

excellent picture quality with a total recording time of 150 minutes.

'EP/EP': ExtendedPlay (better than VHS picture quality). Total

recording time of 240 minutes

'EP+/EP+': ExtendedPlay (VHS picture quality). Total recording time of

360 minutes.

Can I also change the recording mode via a menu?

Press the SYSTEM-MENU button.

Select ' ' using D or C .

Select 'Record settings' (in the second screen of menus) using

B or A then press C .

At 'Rec Mode,' select the recording mode using D or C .

Confirm with OK then press SYSTEM-MENU .

If you select the 'EP/EP' or 'EP+/EP+' recording modes, you can

select the 'Stndrd' (standard) or 'Sport' (for quick movements)

settings in the 'Filter mode' line.

Tip

Recording

IManaging disc content

General information

Charly 1

00:29:59 • HQ

Fr15/02/2002

When a recording is made on a disc, the following information is saved at the start of each

recording:

•) Name of the recording

Empty title

01:30:01

If no name is sent by the broadcaster, then

the channel number (channel name) and time the recording started is saved as the name

•) Length of recording

•) Recording mode (quality)

•) Date of the recording

•) Recording index screen

If 'Auto chapters' is turned on in the 'Record settings' menu, a marking will be made every

5-6 minutes. These markers are called chapter markers.

Can markings also be made on DVD+Rs?

Markings can be made on these discs as long as they have not been

finalized.

Read 'Disc settings'to change general settings of the disc.

Read 'Editing recording titles (name)'to learn how to change recording names.

Read 'Playing the entire title'to learn how to play the entire title.

Read 'Deleting recordings/titles'to learn how to erase the title.

Read 'Edit menu'to learn how to make a new index picture.

Managing disc content

Editing recording titles (name)

Some TV stations transmit the name of a program. In this case, the name may be included

automatically (e.g. 'ROCKY'). Otherwise, the date and time of the recording are stored as the

name. The name of the recording can only be changed after the recording has been completed.

Press STOP h to stop playback if necessary.

Using A or B , select the title you want to edit and confirm

with C . The settings menu for that title will appear.

Settings for title Charly 1

Name

Charly 1

Select 'Name' using A or B and confirm with C .

Play full title

Erase this title

Using

C or

D , select the position where the

letter/number/symbol is to be changed.

Change the desired symbol using A or B . You can switch

between uppercase and lowercase letters with the

SELECT button. You can delete

character with the

CLEAR button.

Repeat steps 4 and 5 until you have made the desired changes.

Save the new name with OK . 'Storing name' appears on the

TV screen for confirmation.

To end, press D .

Playing the entire title

If you have hidden certain chapters of a title, with this setting you can view the entire title

including the hidden chapters. Proceed as follows:

Press the STOP h button to stop playback if necessary.

Using A or B select the title that you want to play back then

press C . The settings menu appears.

Settings for title Charly 1

Name

Charly 1

Select 'Play full title' using A or B and confirm with OK .

Play full title

Erase this title

Press OK

Playback begins automatically. The full title - including the hidden

chapters - is played.

Managing disc content

Deleting recordings/titles

You can erase selected recordings from a disc. To do this, proceed as follows:

Press STOP h to stop playback if necessary.

Using A or B to select the title to be deleted then press C .

The settings menu will appear.

Settings for title Charly 1

Name

Charly 1

Select 'Erase this title' using A or B and OK . 'This will

completely erase this title'. 'Press OK to confirm' will

appear on the screen.

Play full title

Erase this title

Press OK

If you want to delete this title, confirm with OK . Otherwise,

press D .

'Erasing title' will appear on the screen.

An 'Empty title' box will now appear at this location in the

index picture screen. New recordings can now be added at this

location.

If the deleted title was too short (less than one minute), no

'Empty title' will appear at this point.

Can titles also be deleted on DVD+Rs?

Titles on DVD+R are marked as deleted. 'Deleted title' appears on the

TV screen instead of 'Empty title.' During playback the deleted title will

be skipped. The location on the disc used for this title cannot be reused

since the title has not been physically deleted. After a disc has been

finalized, no further changes can be made.

Managing disc content

Disc settings

Magnavox1

00:35:59 used

Fr15/02/2002

This display is located before the first title and contains general information about the inserted

disc.

You can:

NTSC

•) change the disc name

•) protect or unprotect a disc

•) finalize editing (make DVD compatible)

•) finalizing DVD+Rs

DVD playback

•) Erase DVD+RWs

To show this display, proceed as follows:

Press STOP h to stop disc playback if necessary.

Select the first title with A or press STOP h again.

Press the A button. The disc information screen will appear.

Changing disc name

Press C in the 'Disc info display'. The 'Settings for' menu will

appear on the screen.

Select the 'Disc name' line using A or B and confirm with

C .

Settings for Magnavox1

Disc name

Protection

Erase disc

Magnavox1

Unprotected

Using

C or

D select

the

position

where

the

letter/number/symbol is to be changed/re-entered.

Change the desired symbol using A or B . You can switch

between uppercase and lowercase letters with the

SELECT button. You can re-delete

CLEAR button.

character with the

Repeat step 3 and step 4 until you have made the desired

changes.

Save the new title with OK . 'Storing name' appears on the TV

screen for confirmation.

To end, press D .

Managing disc content

Finalize editing

If one or more titles have been edited, it is possible that another DVD Player will display the

original titles. You can prepare your disc so a DVD player willplay the edited version.

Press C in the 'Disc info display'. The 'Settings for' menu will

appear on the screen.

Select the line 'Make edits compatible' using A or B and

confirm with OK .

aThe line 'Make edits compatible' does not appear

b Your disc is already compatible. It does not need to be converted.

Problem

To end, press SYSTEM-MENU .

'This will take...' will appear on the screen to show how long

this process will last.

To confirm, press OK . 'Working...' will appear on the TV

screen. A bar moving from left to right will show the progress of

the conversion.

Finalizing DVD+R discs

This function is necessary so that a DVD+R can be played in a DVD player. When this function

is completed, no further recordings or changes can be made to the disc.

Press C in the 'Disc info display'. The 'Settings for' menu will

appear on the screen.

Select 'Finalize disc' using A or B and OK .

a'Finalize disc' does not appear in the display.

b Either no DVD+R was inserted or the disc has already been finalized.

To end, press SYSTEM-MENU .

aThe 'Settings for' menu does not appear

b If the disc was made on another DVD recorder, it is possible that this

menu cannot be opened. In this case, use the 'Finalize disc' function

Problem

in the '

' menu, submenu 'Features'.

'This will take...' will appear on the screen to show how long

this process will last.

To confirm, press OK . 'Working...' will appear on the screen. A

bar moving from left to right will show the progress of the

process.

Managing disc content

Erasing DVD+RWs

Press C in the 'Disc info display'. The 'Settings for' menu will

appear on the screen.

Select Erase discusing A or B and press OK . 'This will

erase all titles' Press OK to confirm' appears on the screen.

Settings for Magnavox1

Disc name

Protection

Erase disc

Magnavox1

Unprotected

Press OK

If you want to delete all titles, confirm with OK . Otherwise,

press D .

'Erasing disc' will appear on the TV screen.

After the disc has been successfully erased, the index picture

screen will be empty. Tip: If the disc is empty already, you cannot

select Erase disc.

Edit menu

In this menu, you can adjust a title to your personal preferences. You can insert/delete chapter

markers or split the title. Display this menu during playback using EDIT on the remote control.

Changing the index picture

Normally, the first frame of a recording is shown as the title's index picture. You can, however,

use any picture as an index picture.

During playback, find the location that you want to use as the

new index picture. Press the PLAY/PAUSE G9 button to

pause play.

Press the EDIT button. The 'Edit menu' menu will appear on

the screen.

Edit menu

Select 'New index picture' and confirm with OK .

New index picture

Divide title

Press OK

Press OK again to confirm. 'Updating menu' appears on the

TV screen.

Press EDIT to exit

When successfully completed, the DVD recorder automatically brings you back to the index

picture screen.

Managing disc content

Splitting titles

A title can be split into several parts (titles) no matter how large. Each of these parts (titles) is

characterized by its own index picture.

Warning! Once a title is split, it cannot be reversed.

Can I also divide titles on DVD+Rs?

Because recordings on DVD+Rs cannot be overwritten, it is not possible

to divide titles.

During playback, press EDIT on the remote control. The 'Edit

menu' menu will appear on the screen.

Edit menu

Press B to select 'Divide title' and confirm with the

OK button.

New index picture

Divide title

Press OK

If you are certain, start the process with OK . 'Dividing title'

will appear on the screen.

Press EDIT to exit

Wait until the new title is displayed with an index picture in the

index picture overview.

This completes this process.

Managing disc content

JProgramming a recording (TIMER)

General information

Use programmed recording (TIMER) to automatically start and stop a recording at a later date.

The DVD recorder will switch to the right program number and begin recording at the correct

time.

With this DVD recorder, you can pre-program up to six recordings within a period of one year.

To make a programmed recording, your DVD recorder needs to know:

* the date you want to make the recording

* the TV channel numbel

* the start and stop times of the recording

* the recording mode ('HQ/SP+/EP/EP+')

This information is saved in a 'TIMER block.'

Before you begin, makee sure the clock is set. If the clock is not set, the Set Clock menu will

appear when you press the TIMER button.

Programming a recording

(with VCR Plus+^®system)

Thanks to this programming system, you no longer need to tediously enter the date, TV channel,

start and end times. All the information needed for programming is contained in the PlusCode

channel number. This PlusCode number is found in most TV listings for magazines.

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or the TV's Audio/Video In

channel).

With the Recorder on, press TIMER on the remote control.

The programming method selected last is marked.

Select line 'VCR Plus+ system' using B or A and confirm

with C .

Enter the entire PlusCode number. This number is up to 9 digits

long and can be found next to the start time of the TV program

in your TV listings magazine.

Timer

VCR Plus+ system

e.g.: 5-234-89 or 5 234 89

PlusCode number

- - - - - - - - -

Enter 523489 for the PlusCode number.

If you make a mistake, you can clear your instructions with

CLEAR .

Mo-Fr/Weekly

Press SELECT

To store

Press OK

Selecting daily/weekly recordings

Using SELECT , select from the following options:

'Mo-Fr': Repeated daily recordings from Monday to Friday.

'Weekly': Repeated weekly recordings (every week on the same day).

Tip

Programming a recording (TIMER)

Confirm with OK .

aThe following message appears on the screen: 'Please enter

channel number'

b The channel number of the TV channel has not yet been assigned

Guide. Using C , D or the number buttons 0..9 on the remote

control, select the corresponding Guide channel number (name) of

the TV channel and confirm with OK .

aThe following message appears on the screen: 'PlusCode

number wrong'

b The entered PlusCode number is incorrect. Correct your entry or

cancel using the SYSTEM-MENU button.

b Check the time/date (see chapter 'Initial installation', section 'Setting

the time and date').

aThe following message appears on the screen: 'Date does not

match Mon-Fri'

b A daily recording was entered for the wrong day. Daily programming

can only be used for recordings to be made from Monday to Friday.

Problem

The data appears after confirmation. You can go back to change

the data. Select the field with C or D . Change the information

with A , B or the number buttons 0..9 .

Timer

VCR Plus+ system

Rec

Mode

Date Ch.

01/22 001

Start

End

08:30AM 10:00PM HQ

Changing recording mode in the 'Rec Mode' input field

Select the 'Rec Mode' input field using C . Using B , A select the

recording mode 'HQ, SP+, EP, EP+'.

Tip

To store

Press OK

If all information is correct, press the OK button. The

programming information is stored in a TIMER block.

To end, press TIMER .

Insert a recordable disc in the Recorder.

Switch off the Recorder with STANDBY m .

The programmed recording will only function properly when the

DVD recorder has been switched off using the

STANDBY m button.

If any of the TIMER blocks are in use and the recordings are set ot occur, 's' will light up on

the display.

Programming a recording (TIMER)

Programming a recording

(without VCR Plus+^®system)

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or the Audio/Video In channel).

With the Recorder on, press TIMER on the remote control.

Select 'Timer Programming' using B or A and confirm with

Timer

Timer Programming

C .

Rec

The information will appear on the screen.

Date Ch. Start

End

Mode

01/22 01

08:30AM 10:00PM HQ

Select an item (date, channel, start, end, or Rec mode) with

D or C .

Enter information with B or A or with the number buttons

0..9 .

Mo-Fr/Weekly

Press SELECT

To store

Press OK

For 'Date', enter the month and then the date.

Selecting daily/weekly recordings

While date is selected, use SELECT to choose from the following

options:

'Mo-Fr': Repeated daily recordings from Monday to Friday

'Mo': Repeated weekly recordings (every week on the same day, e.g.

Monday).

Program numbers ofthe ' EXT1' and 'EXT2' cinch socket

You can also program recordings from external sources via EXT 1 TO

TV-I/O ('EXT1') or EXT 2 AUX I/O ('EXT2').

Changing recording mode in the 'Rec Mode' input field

Select the 'Rec Mode' input field using C .

Using B , A select the recording mode 'HQ, SP+, EP, EP+'.

Tip

If all information is correct, press the OK button. The

information is stored in a TIMER block.

To end, press TIMER .

Insert a recordable disc in the Recorder.

The disc is checked.

Switch the Recorder off with STANDBY m .

The programmed recording will only function properly when the

DVD recorder has been switched off using the

STANDBY m button.

If any of the TIMER blocks are in use, 's' will light up on the display.

Programming a recording (TIMER)

How to check, change, or delete a

programmed recording (TIMER)

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or the Audio/Video In channel).

With the Recorder on, press TIMER on the remote control.

Select 'Timer List' using B or A and confirm with C .

Select the programmed recording you want to check, change, or

delete with B or A .

Timer

Timer List

Rec

Date Ch. Start

01/22 01

--/-- ----- --:--

End

Mode

04:25PM 06:05PM HQ

Delete programmed recording

--:--

---

Press the CLEAR button.

Confirm with OK . 'Timer Cleared' will briefly appear on the TV

screen.

Total record time: 01:40

'--' appears rather than the displayed values

To end, press TIMER .

To change

Press ›

To exit

Press TIMER

Tip

Press C .

Select a field with D or C .

If required, change the information with A , B or the number

buttons 0..9 .

In 'Date', you first enter the month and then the date.

Confirm with OK .

To end, press TIMER .

Switch off with STANDBY m .

Programming a recording (TIMER)

Problem solving for programmed

recordings

PROBLEM

SOLUTION

DVD recorder does not

respond

bWhile a programmed recording is being made, you cannot operate your DVD recorder

manually. If you want to cancel the programmed recording, press STANDBY m .

'Switch off, timer recording'

flashes on the TV screen.

bThe DVD recorder was switched on before the start of a programmed recording.

Turn off the DVD recorder by pressing STANDBY m . A programmed recording (timer) will

only function if the DVD recorder is switched off (button STANDBY m ).

Error message: 'Insert

recordable disc'

bEither no disc was inserted or a disc was inserted that cannot be used for recordings. Insert a

disc that can be recorded upon. Turn off the DVD recorder by pressing STANDBY m .

The message 'Disc locked'

flashes briefly on the

screen.

bA protected disc was inserted. Undo the erase protection or insert a different disc.

Error message: 'Memory

full'

bIf this error message appears after pressing TIMER , then all TIMER blocks are already

programmed. No more recordings can be programmed. Press the C button. If you want to

clear or check a programmed recording, select it with A or B .

The 'Data error' message

appears on the screen.

bThe data for the recording could not be transferred. Please check date, start time, and end

time of the programmed recording.

The message 'Collision'

appears on the screen.

bThe timer recorder overlaps with another timer recording.

bIf you ignore this warning, the programmed recording with the early start time will start first.

The second recording will then lack the beginning.

bChange the information from one of the two recordings.

bDelete one of the two recordings.

Programming a recording (TIMER)

KUser preferences

This section explains how to customize the DVD recorder to your preferences. These icons

indicate the following:

Picture settings

Sound settings

Language settings

Additional settings

Recording settings

Installation

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or Audio/Video In).

Press SYSTEM-MENU on the remote control. The menu bar

will appear at the top of the TV screen.

Select ' ' with D or C and confirm with B .

Select the corresponding function with B or A and confirm

with C .

Select the corresponding line with B or A and confirm with

the C button. Choose an item you want to adjust, using the

instructions provided on the following pages.

Select the corresponding function with B or A , or select the

setting with D or C . Choose an item you want to adjust, using

the instructions provided on the following pages.

Confirm the new setting by pressing OK .

To close the menu item, press D . To remove the menus, press

SYSTEM MENU repeatedly.

User preferences

Picture settings

You can select the following functions in this menu:

'TV shape'

Picture

TV shape

16:9

Off

The picture signal can be adjusted to fit your TV:

Black level shift

Video shift

'4:3 letterbox' for a 'wide-screen' display with black bars on the top and bottom

'4:3 panscan' for a full-height picture with the sides trimmed

'16:9' for wide-screen TV

'Black level shift'

Adapts the color dynamic for NTSC playback when set to ON.

'Video shift'

This allows you to move the picture left or right using the D , C buttons in order to adjust

the picture to your TV screen.

Sound settings

Depending on the audio outputs being used, this menu provides you with a selection of settings.

If you are only using the analog audio outputs (red and white AUDIO OUT L/R), select 'Off' in

the 'Digital output' menu.

'Digital output'

You can select from the following settings for devices connected to the DIGITAL AUDIO

OUT jack.

Sound

Digital output

Analog output

Night mode

All

Stereo

Off

'All': Dolby Digital and DTS signals are going out unchanged to the digital output. MPEG-2

Multi-channel signals are converted to PCM (Pulse Code Modulation).

Use receivers/amplifiers with a digital Multi@channel sound decoder.

'PCM only' : Dolby Digital and MPEG-2 Multi-channel signals are converted to PCM (Pulse Code

Modulation).

Use receivers/amplifiers without a digital Multi@channel sound decoder.

'Off' : digital output turned off.

Use devices with an analog audio input.

User preferences

'Analog output'

You can select from the following settings for devices connected to the analog outputs (AUDIO

OUT L/R).

Stereo: For devices that use neither DolbySurround nor TruSurround. Only use this setting

when the DVD recorder is connected to a stereo TV.

Surround: Dolby Digital and MPEG-2 Multi-channel are mixed to a Dolby Surround-compatible

two-channel output.

Use devices with a Dolby Surround / Pro Logic decoder .

'Night mode'

Night mode optimizes the sound dynamic for low volumes When turned on. This provides less

disturbance in quiet environments. This setting only functions with Dolby Digital Audio on

DVDs.

Language settings

You can select the following settings in this menu:

'Playback audio'

Language of DVDs

Language

Playback audio

Recording audio

Subtitle

English

Stereo

English

'Recording audio'

Audio recording of a TV channel

'Subtitle'

Subtitle language for DVDs

'Menu'

Recorder menu language

User preferences

Additional settings

You can select the following functions in this menu:

'Access control'

Please read the chapter on Child lock.

Features

Enter code...

Access control

Status field

Off

'Status field'

Auto resume

Low power standby

Along with the on screen menu, the OSD (On Screen Display) also displays the current

operating status on the TV screen (counter, playback, recording, TV channel,...).

You can switch off the information about the operating status so as to avoid recording this

information when making recordings.

'On': The Status Box appears with every selected mode for a few seconds, then disappears again.

'Off': The Status Boxes will not appear on the TV screen.

Auto resume

If playback of a pre-recorded DVD or VCD is interrupted ( STOP h or OPEN/CLOSE ),

playback will be restarted at the exact location when the disc is reinserted. This function only

applies to the last 20 discs you played.

If desired, this function can be turned off.

Low power standby

To save energy, you can switch off the clock display on the DVD recorder. Programmed

(TIMER) recordings will still take place.

'On': If the DVD Recorder is switched off using STANDBY m , the clock display is also switched

off.

'Off': If the DVD Recorder is switched off using STANDBY m , the clock display is visible.

'PBC'

This line only appears when a VCD has been inserted.

This function is used to activate or deactivate the PBC menu (playback control) of the Video

CDs. For more information, please see the chapter on "Playback", "Playback of a (Super) Video

CD.

User preferences

LChild lock

Child lock (DVD and VCD)

This function can prevent children from viewing discs.

When in use, a four-digit code (PIN) must be entered in order to play a disc.

In addition, you can set a disc to be played 'always' or 'once' despite the child lock.

•)Play always:

This disc has been placed in a list of 50 other 'child safe discs'. When more than 50 discs have

been added to the list, the oldest disc is removed to make room for the new one. 'Child safe'

will appear on the screen at the start of playback.

•)Play once:

This disc can be played only once. The PIN must be reentered the next time you try to play the

disc.

Activating/Deactivating the child lock

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or the Audio/Video In channel).

Turn on the DVD recorder by pressing STANDBY/ON .

Press SYSTEM-MENU . The menu bar will appear at the top of

the TV screen.

Select ' ' using D or C .

Select line 'Features' using B or A and confirm with C .

'Access control' will be selected. Press C .

Press the number buttons to enter a four-digit code of your

choice. If this is you first time entering your code, you must

enter this code a second time to confirm it.

Select 'Child lock' using A or B and press C .

Select ' ' using B or A .

Confirm with OK .

To end, press D and SYSTEM-MENU .

If you activated Child Lock, you will need to enter the four-digit PIN in order to play locked

discs.

Child lock

Authorizing discs

Insert a disc. After a short check, the access control menu will

appear on the TV screen.

Using A or B , select 'Play once' or 'Play always.'

Use the number buttons 0..9 to enter your PIN.

Double-sided DVDs can have a unique ID number for each side. To completely authorize these

discs, you must authorize each side separately. 'Multi-track' VCDs can also have a unique ID

number for each track. To authorize the complete set, each track must be authorized separately.

Locking authorized discs

Proceed as follows to lock an authorized disc.

Insert the disc. Playback starts automatically. If playback does not

start automatically, press PLAY/PAUSE G9 .

Press STOP h while the icon '

' is being displayed. The

icon will change to '

use.

'. This disc is now locked for further

Child lock

Parental control (DVD video only)

Movies on DVDs may contain scenes which are not suitable for children. DVDs sometimes come

with rating information for the entire DVD or only for certain scenes.

Affected scenes are rated from 1 to 8. If a scene with such a rating is recognized during

playback, the DVD recorder compares the Parental control rating with that of the DVD scene. If

the scene rating exceeds the Parental control rating, an alternative scene will be played back (if

available).

Activating/Deactivating the parental

control

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4).

Turn on the DVD recorder by pressing STANDBY/ON .

Press SYSTEM-MENU . The menu bar will appear in the

display.

Select ' ' using D or C .

Select line 'Features' using B or A and confirm with C .

'Access control' wil be selected. Press C .

Features

Enter code...

Enter a four-digit code of your choice. If you are entering the

code for the first time, you must enter it again to confirm.

Access control

Status field

Off

Auto resume

Select 'Parental level' with A or B and confirm with C . A

bar appears for selecting the parental control level.

Low power standby

Select the corresponding parental level using B , A or the

number buttons 0..9 .

What do the parental levels mean?

Rating 0 (displayed as '--') parental control is not active.

Rating 1 (childsafe)

Rating 8 (for adults only)

What happens when a DVD scene with a higher rating than

authorized is played?

If the recorder cannot find a suitable alternative, playback is stopped

until the four-digit code is entered.

Tip

Confirm with OK . To remove the menus, press D and

SYSTEM-MENU .

Child lock

Most DVDs apply the rating to an entire DVD. Therefore, if certain scenes exceed the rating

you select, the entire disc will be blocked from viewing.

Changing the country

The Parental Contro levels depend on the country in which the DVD was manufactured.

Therefore, it is necessary that you enter the country for which these filter values apply.

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or Audio/Video in).

Turn on the DVD recorder by pressing STANDBY/ON .

Press SYSTEM-MENU . The menu bar will appear in the

display.

Select ' ' using D or C .

Select line 'Features' using B or A and confirm with C .

'Access control' will be selected. Press C .

Features

Enter code...

Enter your four-digit code. (You may have to enter it twice to

confirm it.)

Access control

Status field

Off

Auto resume

Select 'Change country' using A or B and confirm with C .

Low power standby

Select your country ot that of the DVD using A or B and

confirm with OK .

To end, press SYSTEM-MENU .

Child lock

Changing the PIN

Switch on the TV. If required, select the channel number for the

DVD recorder (channel 3 or 4 or Audio/Video in channel).

Turn on the DVD recorder by pressing STANDBY/ON .

Press SYSTEM-MENU . The menu bar will appear in the

display.

Select ' ' using D or C .

Select line 'Features' using B or A and confirm with C .

'Access control' wil be selected. Press C .

Features

Enter code...

Enter your four-digit code. (You may have to enter the code

twice to confirm it.)

Access control

Status field

Off

Auto resume

Select the line 'Change code' using A or B and confirm with

C .

Low power standby

Enter the new code with the number buttons 0..9 . Enterthe

code again to confirm the change.

To end, press SYSTEM-MENU .

I forgot my code.

When it asks for the code, press the STOP h button four times and

then press OK . The code entry is now deactivated. You can now enter

a new code as described above.

Tip

Child lock

MBefore you call technical support

If you have any problems using this DVD recorder, it may be caused by one of the following

reasons. You can also call the customer service centerin your country.

The telephone numbers are listed in the warranty booklet provided.

Have the model number (MODEL NO) and the production number (PROD.NO) ready.

The serial number (PROD. NO.) is printed on the type plate fixed at the rear of the set.

PROBLEM

SOLUTION

Your DVD recorder does

not respond to any button

being pressed, and 'IS TV

ON?' appears in the display:

bDevice is in initial installation mode. Turn on the TV and set it to the Audio/Video In channel

or channel 3 or 4.

Now the menu for language selection should appear. Please read 'Initial Installation' in

'Installing your DVD Recorder'.

The device does not react

to the touch ofa button, or

the remote control is

working

b'Dealer Mode' is on. All buttons at the front of the Recorder are locked.

To switch off this function:

Disconnect the recorder from the power supply.

Press and hold down hSTOP and OPEN/CLOSE and re-connect the recorder to

the power supply.

As soon as the time or '--:--' appears in the display (6 - 10 seconds), release

hSTOP and OPEN/CLOSE .

Your DVD recorder does

not respond to any button

being pressed.

bThere is no power. Check the power supply.

bA programmed recording (TIMER) is currently being made. If desired, cancel the programmed

recording (Timer) with STANDBY m .

bThere is a technical problem. Disconnect from the power outlet for 30 seconds, then connect

again. If this doesn't help, reset your DVD recorder to the default factory settings.

Resetting devices to default

factory settings

bAll the information stored (TV channels, time and date, and TIMER recordings) will be cleared.

Disconnect the Recorder from the power outlet.

Press and hold down the STANDBY/ON button on the front of the Recorder

while reconnecting to the power outlet.

Release STANDBY/ON when 'IS TV ON?' appears in the display. All the

information stored will be cleared.

Read paragraph 'Initial Installation' in 'Installing your DVD Recorder'.

Remote control does not

work.

bThere is a technical problem. Take out the batteries, wait for 10 seconds, and then replace

them.

PboBiantttetrhieesrehmavoeterucnonoturto. lCahtatnhgee Rtheecobradteter.riSeese. if the ?? appears on the display briefly each time

you press a remote control button. If it does, the Recorder is receiving information from the

remote correctly.

No playback on DVD

recorder:

bThere is no recording on the disc. Change disc.

bYou inserted the wrong disc type. Your recorder can play the following disc types: DVD

Video, (Super)Video CD, DVD+R(W) Audio CDs and MP3 CDs.

bYou inserted the disc the wrong way: Insert the disc with the label facing up.

bDisc is dirty. Clean the disc

bWrong region code. The region code of the DVD and the DVD recorder must match.

bParental control is on. Read chapter 'Child lock'

bYou have selected the wrong channel number on the TV for the DVD recorder: On the TV,

select the correct channel number (channel 3 or 4).

bThe cable connecting the TV and the DVD recorder may be loose. Check the cable.

Before you call technical support

PROBLEM

SOLUTION

I cannot playback (Super)

Video CDs

bIt is possible that this (Super) Video CD contains a menu and the 'PBC' is switched off. You

can see this in status field 'PBCOFF '. To activate this function, proceed as follows:

Press SYSTEM-MENU while the (Super) Video-CD is inserted.

Select ' ' using D or C .

Select line 'Features' using B or A and confirm with C .

Select 'On' in line 'PBC' using B or A .

Confirm with OK and end with SYSTEM-MENU .

Poor playback on DVD

recorder (distorted

picture/distorted sound)

bYour TV is not properly adjusted.

bThe disc is dirty. Clean the disc.

bSometimes the picture may be temporarily distorted. This is not a defect of your DVD

recorder.

No recording possible.

bThe TV channel you want to record is not stored or you selected the wrong program

number: Check TV channels stored.

bDisc is write-protected (cannot be recorded on). Remove write-protection or change disc.

For more information, please see 'Preventing accidental erasing of discs' on the 'Manual

Recording' page.

bA finalized DVD+R disc has been inserted. Change disc.

Programmed recording

does not work.

bYou have programmed the wrong time or date. Check time/date.

bYou have not set the TIMER properly. Check the programmed recordings.

bA locked disc inserted. Remove disc lock.

bA finalized DVD+R has been inserted. Change disc.

The wrong TV channel was

entered after you

programmed a recording

using the VCR Plus+

system.

Enter the PlusCode programming number of the desired TV channel.

Confirm with OK .

Check the channel number in the 'Ch.' input field

If this does not correspond to the desired TV channel, select the channel field and

change the channel number.

Confirm with OK .

There is picture or sound

interference with the TV

reception.

bDuring playback via the internal TV tuner ( MONITOR button), switch to recording mode 'HQ'

by pressing REC MODE . This will give you the best possible picture quality.

Before making the recording, select the recording mode as described in 'Selecting the

recording mode (quality)' .

bChange channels at the TV. Press CH- or CH+ to go to channel 4, 3, or Audio/Video In, EXT

IN, ANT IN, etc.

bHave your antenna or Cable TV signal checked.

Distorted sound coming

from a connected hi@fi

amplifier

bThe DVD recorder is connected to the 'Phono-input' of your amplifier. This jack is provided

only for record players without a preamplifier. Connect to a different audio input.

The picture is distorted or

black@and@white during

playback.

bThe TV system of the disc does not match that of your TV (PAL/NTSC).

bThe recording can be made in color only when the TV channels or the connected additional

device sends

color signal. Black-and-white signals without color information (color

subcarriers) cannot be recorded in color.

No sound signal at the

digital output

bCheck whether the sound settings match the selected inputs and connected additional devices.

Before you call technical support

PROBLEM

SOLUTION

A DVD+RW cannot be

played on certain DVD

players

bIf a recording is too short, it is possible that a DVD player cannot detect it. Please observe

the following 'Minimum recording times':

Recording mode 'HQ', 5 minutes; 'SP+', 13 minutes; 'EP', 20 minutes; 'EP+', 30 minutes,

bSome DVD players cannot playback DVD+RW recordings. You can solve this problem by

using a special function.

Open the disc tray with OPEN/CLOSE . Insert the disc but do not close the tray.

Hold down the number button 2 on the remote control until the tray closes. The

disc is modified.

If this fails to produce the desired result, repeat the procedure using the number

button 3 on the remote control.

You can restore the disc to its original condition by pressing and holding 1 .

Warning!

There is a risk that you can no longer play the disc on other DVD players after this

procedure. Therefore, apply this function with particular care.

Other disc errors

bIf it is impossible to play a disc, you can try and repair it for new recordings using the

following function. The disc will only be prepared for deletion. It will be deleted only after the

next recording has taken place.

Clean the disc.

Open the disc tray with OPEN/CLOSE . Insert the disc but do not close the tray.

Hold down CLEAR on the remote control for several seconds until the tray closes.

The disc is prepared for deletion.

Start recording as with an empty disc.

Limited Warranty

DVD Recorder

One year Free Labor / One year Parts Exchange

This product must be carried in for repair.

WHO IS COVERED?

MAKE SURE YOU KEEP...

You must have proof of purchase to receive warranty service.

A sales receipt or other document showing that you purchased

the product is considered proof of purchase.

Please keep your sales receipt or other document showing

proof of purchase. Attach it to the owner's manual and keep

both nearby. Also keep the original box and packing material in

case you need to return your product.

WHAT IS COVERED?

Warranty coverage begins the day you buy your product.

For one year thereafter, all parts will be repaired or replaced, and

labor is free.

BEFORE REQUESTING SERVICE...

Please check your owner's manual before requesting service.

Adjustments of the controls discussed there may save you a

service call.

After one year fromthe day of purchase , you pay for the

replacement or repair of all parts, and for all labor charges.

All parts, including repaired and replaced parts, are covered

only for the original warranty period. When the warranty on

the product expires, the warranty on all replaced and repaired

parts also expires.

TO GET WARRANTY SERVICE IN THE

U.S.A., PUERTO RICO, OR U.S. VIRGIN

ISLANDS...

Take the product to a Magnavox factory service center (see

enclosed list) or authorized service center for repair. When the

product has been repaired, you must pick up the unit at the

center. Centers may keep defective parts.

WHAT IS EXCLUDED?

Your warranty does not cover:

•labor charges for installation or setup of the product,

adjustment of customer controls on the product, and

installation or repair of antenna systems outside of the

product.

•product repair and/or part replacement because of misuse,

accident, unauthorized repair or other cause not within the

control of Magnavox.

(In the U.S.A., Puerto Rico, and U.S. Virgin Islands, all implied

warranties, including implied warranties of merchantability and

fitness for a particular purpose, are limited in duration to the

duration of this express warranty. Because some states do not

allow limitations on how long an implied warranty may last, this

limitation may not apply to you.)

•reception problems caused by signal conditions or cable or

antenna systems outside the unit.

TO GET WARRANTY SERVICE IN

CANADA...

•a product that requires modification or adaptation to enable it

to operate in any country other than the country for which it

was designed, manufactured, approved and/or authorized, or

repair of products damaged by these modifications.

•incidental or consequential damages resulting from the

product. (Some states do not allow the exclusion of incidental

or consequential damages, so the above exclusion may not

apply to you. This includes, but is not limited to, prerecorded

material, whether copyrighted or not copyrighted.)

•a product that is used for commercial or institutional purposes

(including but not limited to rental purposes).

Please contact Magnavox at:

1-800-705-2000

(In Canada, this warranty is given in lieu of all other warranties.

No other warranties are expressed or implied, including any

implied warranties of merchantability or fitness for a particular

purpose. Magnavox is not liable under any circumstances for any

direct, indirect, special, incidental or consequential damages,

howsoever incurred, even if notified of the possibility of such

damages.)

REMEMBER...

WHERE IS SERVICE AVAILABLE?

Please record below the model and serial numbers found on the

product. Also, please fill out and mail your warranty registration

card promptly. It will be easier for us to notify you if necessary.

Warranty service is available in all countries where the product

is officially distributed by Magnavox. In countries where

Magnavox does not distribute the product, the local Magnavox

service organization will attempt to provide service (although

there may be a delay if the appropriate spare parts and technical

manual(s) are not readily available).

Model #:

Serial #:

This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.

Magnavox, P.O. Box 520890, Miami, FL 33152, (402) 536@4171

EL6554E001 / 03-03

FACTORY SERVICE LOCATIONS

NOTE: Magnavox has chosen Philips Factory Service as its preferred, authorized servicer. Please contact a Philips Factory Service

Center. If you reside in one of our Philips Factory Service Branch areas, you can contact the nearest Service Branch to obtain

efficient and expedient repair for your product. If your product is In-Warranty, you should have proof-of-purchase to ensure No

Charge Service. For Out-of-Warranty service, call the location nearest you.

NOTA: Si vous résidez dans une des régions desservies par une succursale de service après vente du fabricant Philips (voir liste

ci-dessous), vous pourrez contacter la branche de service après vente la plus près de chez vous pour obtenir un service après vente

rapide et efficace. Si le produit est sous garantie, il suffira de présenter une preuve d achat pour bénéficier d'un service sans frais.

Pour les produits non couverts par la garantie, contactez le centre le plus près de chez vous.

NOTA: Si Ud. reside en una de nuestras zonas para sucursales Philips de servicio al de fábrica (ver directorio más abajo), Ud. puede

comunicarse con la sucursal de servicio más cercana para obtener una reparación oportuna y eficaz de su producto. Si su producto

está todavía bajo garantía, Ud. debe presentar comprobante de compra para no ocasionar ningunos cargos por servicio. Para servicio

después del vencimiento de la garantía, llame al lugar más cercano de los abajo indicados.

In Canada

To obtain efficient and expedient carry-in, mail-in, or in-home service for your product, please contact Magnavox at:

1-800-661-6162 (French speaking)

1-800-705-2000 (English or Spanish speaking)

Au Canada

Comment obtenir le service après-vente pour les produits apportés ou envoyés par la poste à notre centre de service ou le service à

domicile. Veuillez contacter philips á:

1-800-661-6162 (Francophone)

1-800-705-2000 (Anglais ou Espagnol)

En el Canadá

Cómo recibir servicio efficiente para su producto, en persona, por correo o a domicillo Favor de comunicarse con Philips al:

1-800-661-6162 (francófono)

1-800-705-2000 (Inglés o Español)

Rev. HH - 1/9/2003

FACTORY SERVICE LOCATIONS

QUALITY SERVICE IS AS CLOSE AS YOUR TELEPHONE! SIMPLY LOOK OVER THE LIST BELOW FOR THE NUMBER OF A FACTORY

SERVICE CENTER NEAR YOU. YOUR PRODUCT WILL RECEIVE EFFICIENT AND EXPEDIENT CARRY@IN, MAIL@IN, OR IN@HOME

SERVICE, AND YOU WILL RECEIVE PEACE OF MIND, KNOWING YOUR PRODUCT IS BEING GIVEN THE EXPERT ATTENTION OF

PHILIPS' FACTORY SERVICE.

COMMENT OBTENIR NOTRE SERVICE APRÈS VENTE RAPIDE ET EFFICACE SOIT PAR COURRIER, À

DOMICILE, OU EN SE PRÉSENTANT À UN CENTRE DE SERVICE PHILIPS.PLUS DE 600 CENTRES DE RÉCEPTION DE

PRODUITS À RÉPARER À TRAVERS LE PAYS: CONTACTER LE CENTRE DE SERVICE AUX CONSOMMATEURS LE PLUS PROCHE POUR

SAVOIR L'EMPLACEMENT DE CES DÉPÔTS DANS UN RAYON DE 50 À 75 MILES (80 KM À 120 KM) DU CENTRE DE SERVICE LOCAL.

CÓMO OBTENER UN SERVICIO OPORTUNO Y EFICIENTE POR CORREO, EN CASA O EN PERSONA PARA

SU PRODUCTO A TRAVÉS DE UN CENTRO PHILIPS DE SERVICIO. MAS DE 600 SITIOS POR TODO EL PAIS PARA LA

RECEPCION DE PRODUCTOS NECESITADOS DE REPARACIONES: COMUNICARSE CON EL CENTRO DE SERVICIO DE FABRICA MAS

CERCANO PARA ESTOS LUGARES DENTRO DE UN RADIO DE 80 A 120 KM (50 A 75 MILLAS) DEL CENTRO DE SERVICIO LOCAL.

ATLANTA

CLEVELAND

CHICAGO

Philips Factory Service

550 Franklin Road., Suite F

Marietta, GA 30067

800-273-1501

Philips Factory Service

950 Keynote Circle

Brooklyn Heights, OH 44131

800-331-7037

Philips Factory Service

1279 W. Hamilton Pkwy.

Itasca, IL 60143

800-531-2922

TAMPA

DETROIT

KNOXVILLE

Philips Factory Service

One Philips Drive

Building 2

Knoxville, TN 37914

800-821-1767

Philips Factory Service

1911 US Highway 301 North,

Suite 100

Tampa, FL 33619

800-442-2027

Philips Factory Service

25173 Dequindre

Madison Heights, MI 48071

800-438-1398

SAN FRANCISCO

Philips Factory Service

681 East Brokaw Rd.

San Jose, CA 95112

800-300-9013

DALLAS

PHILADELPHIA

Philips Factory Service

354 Dunks Ferry Rd.

Bensalem, PA 19020

800-847-9320

Philips Factory Service

415 N. Main Street, #107

Euless, TX 76040

800-952-3254

HOUSTON

LOS ANGELES

Philips Factory Service

20930 Bonita, Ste. V

Carson, CA 90746

800-300-9013

Philips Factory Service

1110 N. Post Oak Rd.,

Suite 100

Houston, TX 77055

800-952-3254

Rev. HH @ 1/9/2003

MDV630R/MDV650R

Intel GA 8N SLI User Manual
KitchenAid W10086190 User Manual
Lenovo 2248 0CE User Manual
Lenovo ThinkVision L192P User Manual
Omron Computer Hardware C200HX User Manual
Oricom ECO5100 User Manual
Philips 31224359635103 User Manual
Philips BRILLIANCE 221B3 User Manual
Philips CD195 User Manual
Philips DVP5980K User Manual