Thank you for purchasing the GE Wireless Metallic Thin-Profile Keyboard and
Mouse. This User’s Manual contains all of the information needed to operate your
keyboard and mouse.
1. Introduction
Do away with cables and take control of your applications. The Wireless Metallic Thin-Profile
Keyboard and Mouse are specially designed to optimize your efficiency and provide a complete
wireless solution. With 13 special PC keys and 11 special Mac keys, you can execute your favorite
commands instantly from your desktop! This wireless solution is designed to maximize your total
productivity no matter what operating system you are running!
*For Windows® 7 or later operation systems, NO driver is required; you can just plug-and-play!
*For Mac 10.3 or later operation systems a driver is required.
2. Package Contents
• Wireless Metallic Thin-Profile Keyboard
• Wireless Metallic Mouse
• Nano Receiver (in mouse’s battery compartment)
• Two AAA batteries for Keyboard
• Two AAA batteries for Mouse
• User’s Manual
• Mac Driver CD-ROM
3. System Requirement
• Pentium 1 GHz or higher processor
• Microsoft® Windows® XP, Vista or 7
• Mac 10.3 and higher
• 512 MB of RAM recommended
• 4 GB of available hard disk space
• USB Port
Page 3
4. Installation Instructions
Please keep this user’s manual in a safe place.
1). Connecting receiver to PC
(i) Plug the USB receiver into an available USB port of your PC. The USB receiver is located in the
battery compartment of the mouse.
2). Insert the batteries with correct orientation into the battery compartments of both keyboard and mouse
respectively.
3). Turn the power switch in the bottom of the mouse to the “ON” position.
4). This wireless keyboard and mouse set provides factory preset connection channels and enables Plug
and Play function.
Note:
1. This keyboard and mouse set does not require changing connection ID as there is no ID button on the
Nano receiver.
2. When this wireless set encounters radio interference, either keyboard or mouse will automatically
change to a clean channel respectively. Manually changing connection ID is not necessary.
3. For Mac 10.3 and higher you will have to use the driver provided in order to use the Mac oriented
function keys.
Page 4
5. Special Function Hot Keys
The Wireless Metallic Thin-Profile
Keyboard will come preset with these
function keys and shortcuts. In order to
toggle between the function key and the
Multimedia hotkeys, FN needs to be
selected or deselected
Page 5
6. Special Mouse Functions
Left Mouse Button
Scroll Wheel
Right Mouse Button
1000 DPI Sensor (on bottom)
7. Troubleshooting
• The Wireless Metallic Thin-Profile Keyboard or Mouse stops working
After periods of inactivity, the mouse goes into sleep mode to save batteries. To awake the
mouse just simply move it in any direction and it should respond on the screen.
You may need to change the batteries. You will need 2 AAA batteries for the Wireless
Metallic Thin-Profile Keyboard, and 2 AAA batteries for the Wireless Metallic Mouse.
If you still cannot solve the problem, please contact Jasco Products Company at
8. 2 Year Limited Warranty
TWO YEAR LIMITED WARRANTY: Jasco Products Company warrants this product to be free from
manufacturing defects for a period of 2 years from the original date of consumer purchase. This warranty
is limited to the repair or replacement of this product only and does not extend to consequential or
incidental damage to other products that may be used with this unit. This warranty is in lieu of all other
warranties express or implied. Some states do not allow limitations on how long an implied warranty
lasts or permit the exclusion or limitation of incidental or consequential damages, so the above limitations
may not apply to you. This warranty gives you specific rights, and you may also have other rights which
vary from state to state. If unit should prove defective within the warranty period, return prepaid with
dated proof of purchase to:
Jasco Products Company
10 E. Memorial Road
Oklahoma City, OK. 73114
Page 6
9. FCC Statement
Notice: Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes of modifications not expressly approved by the grantee of this device could
void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Page 7
|