|
HS-2601A
Intel Low Power Mobile 500MHz
Mini Board Computer
•3.5” Size•All-in-One•CRT/Panel•LAN•WDT•
•DOC•2 USB•IrDA•PC/104•Flash Disk•
•PCI Bus Mini Board•
Table of Contents
Chapter 1 General Description ---------------------------------6
1.1 Major Features ------------------------------------------------------2
1.2 Specifications -------------------------------------------------------3
1.3 Board Dimensions -------------------------------------------------4
Chapter 2 Unpacking ---------------------------------------------5
2.1 Opening the Delivery Package---------------------------------5
2.2 Inspection-------------------------------------------------------------5
Chapter 3 Hardware Installation-------------------------------7
3.1 Before Installation--------------------------------------------------7
3.2 Board Layout --------------------------------------------------------8
3.3 Jumper List-----------------------------------------------------------9
3.4 Connector List ------------------------------------------------------9
3.5 Configuring the CPU ----------------------------------------------9
3.6 System Memory--------------------------------------------------- 10
3.7 DiskOnChip Address Setting ------------------------------ 10
3.7.1 Installing DiskOnChip Modules------------------------------- 10
3.7.1 Removing DiskOnChip Modules -------------------------------11
3.8 VGA Controller---------------------------------------------------- 12
JP2: Panel Voltage Select--------------------------12
CN6: 15-pin CRT Connector (DB15) ---------------12
CN10: 50-pin Panel Connector --------------------13
3.9 IDE Drive Connector--------------------------------------------- 14
CN12: Primary IDE Connector ---------------------14
3.10 Floppy Disk Drive Connector--------------------------------- 15
CN11: FDD Connector------------------------------15
3.11 Serial Port Connectors ----------------------------------------- 16
CN15 and CN14: COM1/COM2 Connector
(5x2 Header)----------------------------------------16
3.12 Parallel Connector ----------------------------------------------- 16
CN16: Parallel Connector--------------------------16
3.13 Ethernet Connector---------------------------------------------- 17
CN4: RJ-45 and LAN LED Connector --------------17
3.14 IrDA Connector --------------------------------------------------- 17
CN9: IrDA Connector-------------------------------17
3.15 USB Connector --------------------------------------------------- 18
CN13: USB Connector ------------------------------18
3.16 CMOS Data Clear------------------------------------------------- 18
JP4: Clear CMOS------------------------------------18
3.17 Power Connectors ----------------------------------------------- 18
CN1: 4-pin Power Connector ----------------------18
CN5: 2-pin Power Input Connector----------------19
3.18 Keyboard/Mouse Connectors -------------------------------- 19
CN8: 6-pin Keyboard/Mouse Connector ---------19
CN7: PS/2 6-pin Mini DIN Keyboard/Mouse
Connector-------------------------------------------19
3.19 System Front Panel Connectors ---------------------------- 19
LD2: IDE LED Connector ----------------------------19
LD1: Power LED--------------------------------------20
JP3: Reset Button Connector-----------------------20
3.20 Watchdog Timer -------------------------------------------------- 20
JP1: Watchdog Timer Active Type Setting -------20
3.21 CompactFlash Connector----------------------------------- 22
3.22 Mini PCI Connector ---------------------------------------------- 23
PC1: Mini PCI Connector Pin Information ---------23
3.23 PC/104 Connectors ---------------------------------------------- 25
CN3: 40-pin PC/104 Expansion Slot ---------------25
CN2: 64-pin PC/104 Expansion Slot ---------------26
Chapter 4 Award BIOS Setup -------------------------------- 27
4.1 Starting Setup ----------------------------------------------------- 27
4.2 Using Setup -------------------------------------------------------- 28
4.2.1 Getting Help-----------------------------------------------------------28
4.3 Main Menu ---------------------------------------------------------- 29
4.4 Standard CMOS Setup------------------------------------------ 31
4.5 BIOS Features Setup-------------------------------------------- 34
4.6 Chipset Features Setup ---------------------------------------- 39
4.7 Power Management Setup ------------------------------------ 43
4.7.1 PM Timers -------------------------------------------------------------45
4.7.2 Reload Global Timer Events --------------------------------------46
4.8 PNP/PCI Configuration ----------------------------------------- 47
4.9 Load BIOS Defaults---------------------------------------------- 48
4.10 Load Setup Defaults--------------------------------------------- 49
4.11 Integrated Peripherals ------------------------------------------ 50
4.12 Supervisor/User Password Setting------------------------- 53
4.13 IDE HDD Auto Detection --------------------------------------- 54
4.14 Save & Exit Setup ------------------------------------------------ 55
4.15 Exit Without Saving---------------------------------------------- 56
Chapter 5 Software Utilities----------------------------------- 57
5.1 VGA Driver Installation for Win 95/98---------------------- 57
5.2 VGA Driver Installation for Win NT4.0 --------------------- 59
5.3 LAN Driver Installation for WIN95 & WIN98-------------- 62
5.3.1 Win98-------------------------------------------------------------------62
5.3.2 Win95-------------------------------------------------------------------62
5.4 LAN Driver Installation for Win NT4.0 --------------------- 64
Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity.
To avoid damaging chips from electrostatic discharge, observe the
following precautions:
ꢀ
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
ꢀ
Before handling a board or integrated circuit, touch an unpainted portion
of the system unit chassis for a few seconds. This helps to discharge any
static electricity on your body.
ꢀ
ꢀ
Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR
clip of the strap to the end of the shielded wire lead from a grounded
object. Please wear and connect the strap before handle the HS-2601A
to ensure harmlessly discharge any static electricity through the strap.
Please use an anti-static pad when putting down any components or
parts or tools outside the computer. You may also use an anti-static bag
instead of the pad. Please inquire from your local supplier for additional
assistance in finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
ROTECTION.
This page intentionally left blank.
Chapter 1
General Description
The HS-2601A is a 100MHz Intel® BX chipset-based Mini PCI Bus Intel
Mobile board. With features such as enhanced I/O effects with
CRT/VGA, and LAN all combined, the HS-2601A is an ideal all-in-one
compact-size board for the demanding embedded applications and IA
platforms.
Its onboard DMA33 to IDE drive interface architecture allows the
HS-2601A to support data transfers of 33MB/sec with a maximum of
two IDE drives. Its Intel® BX chipset design makes it possible for the
board to support most Intel Mobile microprocessors in the market, The
C&T 69000 CRT/Panel display controller offers an on-chip 2MB
memory that supports up to 1280x1024x256 colors display resolution.
For suitable installation into any size system with 8/16/32bit ISA and/or
PCI slots operation, the board’s advanced PISA bus add-on feature
allows user to easily obtain both ISA's 16bit and PCI's 32bit full set
signals from a half size PISA slot. System memory is also sufficient
with the two DIMM sockets that can support up to 256MB.
Additional onboard connectors include an advanced USB and IrDA
ports providing faster data transmission,
a
DOS-compatible
DiskOnChip socket with a maximum capacity of 288MB, and one
external RJ45 connector for 10/100 Base-TX Ethernet use.
1
To ensure the reliability in an unmanned or standalone system, the
Watchdog Timer (WDT) onboard HS-2601A is designed with pure
hardware that does not need the arithmetical functions of a real-time
clock chip. If any program causes unexpected halts to the system, the
onboard Watchdog Timer (WDT) will automatically reset the CPU or
generate an interrupt to resolve such condition.
1.1 Major Features
The HS-2601A comes with the following features:
ꢁ BGA Packaged Intel Low Power Mobile CPU at 500MHz, 700MHz, and
800MHz
ꢁ One SO-DIMM socket with a maximum capacity of 256MB
ꢁ Fast PCI DMA33 controller supporting two IDE disk drives
ꢁ Mini PCI Local Bus support
ꢁ Two RS-232 serial ports
ꢁ PS/2 Keyboard and PS/2 Mouse connectors
ꢁ One enhanced bi-directional parallel port supporting SPP/ECP/EPP
modes
ꢁ Winbond W83977 super I/O chipset
ꢁ C&T 69000 CRT/Panel display controller
ꢁ Intel 82559 100 Base-TX LAN controller
ꢁ DiskOnChip memory size up to 288MB
ꢁ PC/104 Bus connector
ꢁ Optional 8~64MB Flash Disk support
2
1.2 Specifications
ꢀ CPU: Intel Low Power Mobil CPU from 500-800 MHz
ꢀ Bus Interface: Mini PCI Local Bus
ꢀ Memory: One SO-DIMM socket supporting up to 256MB
ꢀ Chipset: Intel 82443BX
ꢀ I/O Chipset: Winbond W83977
ꢀ VGA: C&T 69000 with 2MB memory supporting CRT/Panel displays up
to 1280 x1024 at 256 colors
ꢀ IDE: Two IDE disk drives supporting ATA/33 and with a transfer rate up
to 33MB/sec
ꢀ Flash Disk: 8~64 MB IDE interface Flash Disk support (optional)
ꢀ FDD: Supports up to two floppy disk drives
ꢀ Parallel: One enhanced bi-dirctional parallel port supporting
SPP/ECP/EPP
ꢀ LAN: Intel 82559 100 Base-TX LAN
ꢀ Serial Port: Two RS-232 serial ports include 16C550 UART with 16byte
FIFO
ꢀ IrDA: One IrDA TX/RX header
ꢀ USB: Two USB ports
ꢀ CompactFlash: One optional CompactFlash adapter slot on solder
side
ꢀ Keyboard/Mouse: PS/2 6-pin Mini DIN or 6-pin connector
ꢀ DiskOnChip: Socket for DiskOnChip and memory size up to 288MB
ꢀ BIOS: Award PnP Flash BIOS
ꢀ Watchdog Timer: Sets 1, 2, 10, 20, 110, 220 seconds activity trigger
with Reset or NMI
ꢀ CMOS: Battery backup
ꢀ DMA Channels:
7
ꢀ Interrupt Levels: 15
ꢀ PC/104: PC/104 connector for 16bit ISA Bus
ꢀ Main Power: Single +5V power input
ꢀ Extra Power: One 4-pin +12V/-12V connector
ꢀ Max. Power Consumption: +5V@6A
ꢀ Operating Temperature: 0~60 oC
ꢀ Board Size: 10.3 x 14.6 cm
3
1.3 Board Dimensions
4
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-2601A is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
to ensure that they are firmly seated. The HS-2601A delivery package
contains the following items:
ꢂHS-2601A Industrial Single Board
ꢂPrinter Ports Flat Cable x 1
ꢂCOM port Flat Cable x 1
ꢂIDE port Flat Cable x 1
ꢂFDD port Flat Cable x 1
ꢂPS/2 Keyboard/Mouse Transfer Cable x 1
ꢂUtility Disc
ꢂUser’s Manual
5
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.
6
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-2601A. This chapter also contains information related to
jumper settings of switch, watchdog timer, and the DiskOnChip
address selection etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1.
Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper.
2.
Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3.
Keep the manual and diskette in good condition for future
reference and use.
7
3.2 Board Layout
8
3.3 Jumper List
Jumper
JP1
Definition
Watchdog Timer Active Type Select
Default Page
Short 2-3
Short 1-2
Short 1-2
20
12
18
JP2
Panel Voltage Select
JP4
Clear CMOS
3.4 Connector List
Connector
JP3
Definition
Page
20
18
26
25
17
18
12
19
19
17
13
15
14
18
16
16
16
22
19
19
23
10
10
Reset Button
CN1
CN2
CN3
CN4
CN5
CN6
4-pin Power In Connector
PC/104 64-pin Connector
PC104 40-pin Connector
RJ45 and LAN LED Connector
2-pin Power In Connector
CRT Connector
CN7
CN8
CN9
PS/2 6-pin Mini Din KB/Mouse Connector
6-pin Keyboard/Mouse Connector
IrDA Connector
CN10
CN11
CN12
CN13
CN14
CN15
CN16
CN17
LD1
Panel Connector
Floppy Connector
IDE Connector
USB Connector
COM2 Connector (5x2 Header)
COM1 Connector (5x2 Header)
Parallel Connector
CompactFlash Connector
Power LED Connector
HDD LED Connector
Mini PCI Connector
LD2
PC1
U2
SO-DIMM Socket
U7
DiskOnChip Socket
3.5 Configuring the CPU
The HS-2601A, with its onboard BGA processor, auto-detects the
features of the mounted microprocessor onboard. The HS-2601A
automatically identifies the frequency and clock speed of the installed
microprocessor chip, thereby eliminating the need for user to do
additional CPU configuration or hardware settings related to it.
9
3.6 System Memory
The HS-2601A provides one SO-DIMM socket at location U2. This
onboard memory socket can support 64MB, 128MB and 256MB
SO-DIMM modules. The system’s maximum memory capacity is
256MB.
143
144
1
2
144-pin SO-DIMM Socket
pin orientation
NOTE: SO-DIMM sockets out on the market these days have very fragile
contacts that attach to modules. We highly recommend you not to
regularly remove the installed SO-DIMM from its socket. Doing so
may wear out the contact between the socket and module.
3.7 DiskOnChip Address Setting
The DiskOnChip function allows the system to boot or operate
without a FDD or a HDD. DiskOnChip modules may be formatted as
drive C or A. With DiskOnChip, user may also execute DOS
commands such as FORMAT, SYS, COPY, XCOPY, DISCOPY and
DISKCOMP etc.
The U7 location onboard the HS-2601A is the DiskOnChip module
socket. The board circuitry assigns a LOCKED starting memory
address of the installed module at D000. If you have another memory
device that has a similar memory capacity with that of the DOC in your
system, please set both at different memory address mapping to avoid
the mapping area conflicts. Failing to do so will not make the HS-2601A
and the additional memory device function properly.
3.7.1 Installing DiskOnChip Modules
When installing a DiskOnChip module onto your board, please take
note of the following:
1. Orient yourself properly with the location of the DiskOnChip
socket. Try to locate the pin 1 location on your socket. Pin
numbers are usually printed on either the component side or the
solder side of your board.
2. Locate the Pin 1 location on your DiskOnChip module. More
often than not, Pin 1 can be found on the lower right corner of
the chip. Please refer to the diagram for the exact location.
10
3. Once you have figured out where the pin 1 locations are on both
chip and socket, align the module’s pins on an upright angle
against the socket. Using both thumbs, gently press the module
into the socket until all the pins are secured to their
designations.
Pin 1
Location
4. The installation is now complete and your module is now ready
for use.
NOTE: If you encounter difficulty installing your DiskOnChip module,
please consult a qualified technician or engineer to perform the
installation.
3.7.1 Removing DiskOnChip Modules
When removing a DiskOnChip module from its socket, please take
note of the following:
1. Loosen the contact of the module from its socket using a
screwdriver.
2. Insert the screwdriver’s flat head into a gap on either end of the
socket. Do not insert the screwdriver head on either side where
the pins are located. Doing so might damage the pins in the
process.
3. Slowly lift the screwdriver handle upwards. This will disengage
the module from its socket.
NOTE: If you encounter difficulty removing your DiskOnChip module,
please consult a qualified technician or engineer to remove it for
you.
11
3.8 VGA Controller
The HS-2601A has an onboard jumper that selects the working voltage
of the flat panel connected to the system. Jumper JP2 offers two
voltage settings for the user.
ꢃ
JP2: Panel Voltage Select
Options
5.0 V (default)
3.3 V
Settings
Short 1-2
Short 2-3
3
2
1
WARNING: Please contact the supplier of your panel and make sure of
the correct voltage it uses. Incorrect settings on JP8 may
cause internal damage to your panel.
The built-in C&T 69000 CRT/Panel display controller, onboard
HS-2601A, uses 2MB memory to support resolutions up to
1280x1024x256 colors.
The HS-2601A provides two connection methods of a VGA device.
CN20 offers a single standard CRT connector (DB15) while CN16 is
the 50-pin panel connector onboard reserved for flat panel installation.
ꢃ
CN6: 15-pin CRT Connector (DB15)
PIN
1
Description
Red
PIN Description
2
Green
3
Blue
4
N/C
5
GND
6
GND
7
GND
8
GND
9
N/C
N/C
HSYNC
GND
10
12
14
GND
GND
VSYNC
11
13
15
5
1
10
6
15
11
12
ꢃ
CN10: 50-pin Panel Connector
PIN.
1
3
5
7
Description
+12V
GND
3.3V / 5V Note
ENAVEE
P0
PIN Description
2
+12V
GND
ENAVDD
GND
P1
4
6
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
P2
P4
P6
P8
P10
P12
P14
P16
P18
P20
P22
P24
SHFCLK
M
GND
P26
P28
P30
P3
P5
P7
P9
P11
P13
P15
P17
P19
P21
P23
P25
FLM
LP
ENABKL
P27
P29
P31
P33
P35
P32
P34
47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11
9
7
5
3
49
50
1
2
48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8
6
4
NOTE: Please set the proper voltage of your panel using JP8 before
proceeding on installing it.
13
3.9 IDE Drive Connector
CN12, a 44-pin connector, provides the PCI E-IDE drive provisions
onboard. A maximum of four IDE drives may be connected on them.
ꢃ CN12: Primary IDE Connector
CN15
Description
CN15
Description
1
3
5
7
BRSTDRVJ
DD7-1
2
4
6
8
GND
DD8-1
DD9-1
DD10-1
DD11-1
DD12-1
DD13-1
DD14-1
DD15-1
N/C
GND
GND
GND
PRIPD1-
GND
DD6-1
DD5-1
DD4-1
DD3-1
DD2-1
DD1-1
DD0-1
GND
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
RPDDREQ-
RPDIOW-
RPDIOR-
PIORDY
RPDACK-
IRQ14
RPDA1-
RPDA0-
RPCS1-
HLED
N/C
N/C
RPDA2-
RPCS3-
GND
VCC
GND
VCC
VCC
44 42 40 38 36 34 32 30 28 26 24 22 20
16
8
7
6
5
4
18
14 12
10
2
1
43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11
9
3
14
3.10 Floppy Disk Drive Connector
The HS-2601A uses a standard 34-pin header connector, CN11, for
floppy disk drive connection. A total of two FDD drives may be
connected to CN11 at any given time.
ꢃ
CN11: FDD Connector
PIN
Description
PIN
Description
1
3
5
7
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
N/C
2
4
6
8
RWC-
N/C
DS1-
Index#
9
10
12
14
16
18
20
22
24
26
28
30
32
34
Motor Enable A#
Drive Select B#
Drive Select A#
Motor Enable B#
Direction#
Step#
11
13
15
17
19
21
23
25
27
29
31
33
WD-
WE-
Track 0#
WP-
RDATA-
HEAD-
GND
N/C
DSKCHG-
33
34
1
2
u
15
3.11 Serial Port Connectors
The HS-2601A offers two NS16C550 compatible UARTs with
Read/Receive 16byte FIFO serial ports and two internal 10-pin
headers.
ꢃ
CN15 and CN14: COM1/COM2 Connector (5x2 Header)
PIN
Description
PIN
Description
1
3
5
7
9
DCD
RXD
TXD
DTR
GND
2
4
6
8
10
DSR
RTX
CTX
RI
N/C
DSR
RTX
CTX
RI
2
4
1
3
5
7
9
DCD
RXD
TXD
DTR
GND
6
8
N/C
10
CN14 and CN15
3.12 Parallel Connector
CN16 is a standard 26-pin flat cable connector deigned to
accommodate parallel port connection onboard the HS-2601A.
ꢃ
CN16: Parallel Connector
PIN
1
3
Description
STBJ
PD1
PIN
2
4
Description
PD0
PD2
5
PD3
6
PD4
7
PD5
8
PD6
9
PD7
10
12
14
16
18
20
22
24
26
ACKJ
PE
AFDJ
INITJ
GND
GND
GND
GND
GND
11
13
15
17
19
21
23
25
BUSY
SLCT
ERRJ
SLINJ
GND
GND
GND
GND
16
1
2
25
26
3.13 Ethernet Connector
The HS-2601A provides one external RJ-45 10/100 Base-TX LAN
interface connector. Please refer to the following detail of pin
information.
ꢃ
CN4: RJ-45 and LAN LED Connector
PIN
Description
TX+
1
2
3
4
5
6
7
8
9
TX-
RX+
2
8
1
No Use
No Use
RX-
No Use
No Use
GND
7
Aside from the RJ-45 provision onboard the HS-2601A, the board also
features an LED indicator that displays the 10T speed running, 100T
speed running, and active status of the LAN connection.
3.14 IrDA Connector
CN9 is a 5-pin internal IR communication connector for connection of
an IrDA device.
ꢃ
CN9: IrDA Connector
PIN
Description
VCC
N/C
1
2
3
4
5
1
2
3
4
5
VCC
FIRRX
IRRX
GND
IRRX
VCC
IRTX
IRTX
17
3.15 USB Connector
The HS-2601A provides one 8-pin connector for USB0 & USB1 port
connections at location CN13.
ꢃ
CN13: USB Connector
PIN Description PIN Description
1
3
5
7
VCC
BD0-
BD0+
GND
2
4
6
8
VCC
BD1-
BD1+
GND
2
1
8
7
3.16 CMOS Data Clear
The HS-2601A has a Clear CMOS jumper on JP4. The JP4 settings
below apply to the standard HS-2601A using a battery backed up
CMOS chip.
ꢃ
JP4: Clear CMOS
Options
Normal Operation
* Clear CMOS
Settings
Short 1-2
Short 2-3
1
2
3
IMPORTANT: The default setting of JP4 is Short 2-3. Before you turn
on the power of your system, please set JP4 to Short 1-2
for normal operation.
3.17 Power Connectors
HS-2601A provides one 4-pin power connector at CN1 and a single
2-pin power connector at CN5.
ꢃ CN1: 4-pin Power Connector
1
PIN Description
VCC
1
2
3
4
VCC
GND
GND
+12V
GND
GND
+12V
4
18
ꢃ CN5: 2-pin Power Input Connector
PIN Description
1
2
1
+5V
2
GND
3.18 Keyboard/Mouse Connectors
The HS-2601A offers two possibilities for keyboard connections. The
connections are via CN7 for an external PS/2 type keyboard/mouse or
via CN8 for an internal 5-pin cable converter to an AT keyboard.
ꢃ
CN8: 6-pin Keyboard/Mouse Connector
PIN
Description
Keyboard Clock
Keyboard Data
Mouse Data
GND
1
2
3
4
5
6
VCC
Mouse Clock
ꢃ
CN7: PS/2 6-pin Mini DIN Keyboard/Mouse Connector
PIN
Description
Keyboard Data
Mouse Data
GND
VCC
Keyboard Clock
Mouse Clock
1
2
3
4
5
6
3.19 System Front Panel Connectors
The HS-2601A has one LED at location LD1 that indicates the
power-on status. This visual feature of the IDE LED may also be
connected to an external IDE LED via connector LD2.
ꢃ
LD2: IDE LED Connector
PIN
1
Description
1
2
+5V
2
HDD ACTIVE#
19
LD1 and JP3 are the Keylock and Reset Button connectors onboard.
ꢃ
LD1: Power LED
PIN
1
Description
2
1
+5V
2
GND
ꢃ
JP3: Reset Button Connector
PIN
1
Description
1
2
GND
2
External Reset
3.20 Watchdog Timer
There are three access cycles of Watch-Dog Timer as Enable, Refresh
and Disable are the three access cycles of Watchdog Timer. The
Enable cycle proceeds via READ PORT 443H whereas the Disable
cycle proceeds via READ PORT 045H. A continued Enable cycle after
a first Enable cycle means Refresh.
Once the Enable cycle is active, a Refresh cycle is requested before
the time-out period. This restarts counting of the WDT period. When
the time counting goes over the period preset of WDT, it will assume
that the program operation is abnormal. A System Reset signal to
re-start or a NMI cycle to the CPU transpires when such error happens.
Jumper JP1 is used to select the function of Watchdog Timer.
ꢃ
JP1: Watchdog Timer Active Type Setting
Options
Active NMI
System Reset (default)
Disabled Watchdog Timer
Settings
Short 1-2
Short 2-3
Open
3
2
1
The Watchdog Timer is disabled after the system Power-On. It can be
enabled via an Enable cycle and reading the control port (443H), or via
a Refresh cycle and reading the control port (443H), or via a Disable
cycle and reading the disable control port (045H).
20
After an Enable cycle of WDT, user must immediately execute a
Refresh cycle to WDT before its period setting comes to an end every
1, 2, 10, 20, 110 or 220 seconds. If the Refresh cycle does not activate
before WDT period cycle, the onboard WDT architecture will issue a
Reset or NMI cycle to the system. There are three I/O ports that control
the Watchdog Timer.
443H
443H
045H
I/O Read
I/O Read
I/O Read
The Enable cycle
The Refresh cycle
The Disable cycle
The following sample program shows how to Enable, Disable and
Refresh the Watchdog Timer：
WDT_EN_RF
WDT_DIS
EQU
EQU
0433H
0045H
WT_Enable
WT_Refresh
WT_DISABLE
PUSH
PUSH
MOV
IN
POP
POP
RET
AX
DX
; keep AX DX
DX,WDT_EN_RF
AL,DX
DX
; enable the WDT
; get back AX, DX
AX
PUSH
PUSH
MOV
IN
POP
POP
RET
AX
DX
; keep AX, DX
DX,WDT_ET_RF
AL,DX
DX
; refresh the WDT
; get back AX, DX
AX
PUSH
PUSH
MOV
IN
POP
POP
RET
AX
DX
DX,WDT_DIS
AL,DX
DX
; disable the WDT
; get back AX, DX
AX
21
3.21 CompactFlash Connector
The HS-2601A also offers an optional CompactFlash connector
which is IDE interface located at the solder side of the board (beneath
the SO-DIMM connector). The designated CN17 connector, once
soldered with an adapter, can hold CompactFlash cards of various
sizes. Please turn off the power before inserting the CF card. Inserting
a CompactFlash card into the adapter is not a difficult task. The
socket and card are both keyed and there is only one direction for the
card to be completely inserted. Refer to the diagram below for the
traditional way of inserting the card.
r
e
d
l
w
o
e
S
i
V
B
e
C
d
P
i
S
M
T
22
3.22 Mini PCI Connector
HS-2601A supports a Mini PCI interface which is a very popular
notebook computer expansion interface for Modem, Video, LAN,
etc. The Mini PCI onboard HS-2601A is at location PC1 with pin
definitions listed on the table below.
ꢃ
PC1: Mini PCI Connector Pin Information
PIN.
Description
PIN.
Description
1
3
INTB#
3.3V
2
4
5V
D#
5
7
RESERVED
GND
6
8
RESERVED
N.C.
9
CLK
GND
REQ#
3.3V
AD[31]
AD[29]
GND
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
RST#
3.3V
GNT#
GND
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
PME#
RESERVED
AD[30]
3.3V
AD[27]
AD[25]
RESERVED
C/BE[3]#
AD[23]
GND
AD[21]
AD[19]
GND
AD[17]
C/BE[2]#
IRDY#
3.3V
CLKRUN#
SERR#
GND
PERR#
C/BE[1]#
AD[14]
GND
AD[12]
AD[10]
GND
AD[28]
AD[26]
AD[24]
IDSEL
GND
AD[22]
AD[20]
PAR
AD[18]
AD[16]
GND
FRAME#
TRDY#
STOP#
3.3V
DEVSEL#
GND
AD[15]
AD[13]
AD[11]
GND
AD[9]
C/BE[0]#
AD[8]
. . . More on next page . . .
23
PIN.
Description
PIN.
Description
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99
AD[7]
3.3V
AD[5]
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
3.3V
AD[6]
AD[4]
AD[2]
AD[0]
RESERVED
AD[3]
5V
AD[1]
GND
RESERVED_WIP2
RESERVED_WIP2
GND
AC_SYNC
AC_SDATA_IN
AC_BIT_CLK
AC_CODEC_ID1#
MOD_AUDIO_MON
AUDIO_GND
SYS_AUDIO_OUT
M66EN
AC_SDATA_OUT
AC_CODEC_IDO#
AC_RESET#
RESERVED
GND
SYS_AUDIO_IN
2
1
100
99
Mini PCI Socket
pin orientation
24
3.23 PC/104 Connectors
The PC/104 expansion bus offers provisions to connect all types of
PC/104 modules. With the PC/104 bus being known as the new
generation of industrial embedded 16bit PC standard bus, thousands
of PC/104 modules from multiple venders can be easily installed
onboard. The detailed pin assignment of the PC/104 expansion bus
connectors CN10 and CN11 are listed on the following tables:
The PC/104 connector allows direct plugging or stack-through
piling of PC/104 modules without requiring the PC/104 mounting
kit.
NOTE：
ꢃ
CN3: 40-pin PC/104 Expansion Slot
PIN Description PIN Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
GND
MEMCS16*
IOSC16*
IRQ10
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
GND
SBHE*
LA23
LA22
LA21
LA20
LA19
LA18
LA17
MEMR*
MEMW*
SD8
1
21
IRQ11
IRQ12
IRQ15
IRQ14
DACK0*
DRQ0
DACK5*
DRQ5
DACK6*
DRQ6
DACK7*
DRQ7
SD9
SD10
SD11
SD12
SD13
SD14
SD15
N/C
+5V
MASTER*
GND
20
40
GND
25
ꢃ
CN2: 64-pin PC/104 Expansion Slot
PIN Description PIN Description
1
2
3
4
5
6
7
8
IOCHECK*
SD7
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
GND
RESETDRV
+5V
SD6
SD5
SD4
SD3
SD2
SD1
SD0
IRQ9
-5V
DRQ2
-12V
NOW*
+12V
1
33
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
IOCHRDY
AEN
GND
SMEMW*
SMEMR*
IOW*
SA19
SA18
SA17
SA16
SA15
SA14
SA13
SA12
SA11
SA10
SA9
SA8
SA7
SA6
SA5
SA4
SA3
SA2
SA1
IOR*
DACK3*
DRQ3
DACK1*
DRQ1
REFRESH*
SYSCLK
IRQ7
IRQ6
IRQ5
IRQ4
IRQ3
DACK2*
TC
BALE
+5V
OSC
32
64
SA0
GND
GND
GND
26
Chapter 4
Award BIOS Setup
The HS-2601A uses Award PCI/ISA BIOS for the system configuration.
The Award BIOS setup program is designed to provide the maximum
flexibility in configuring the system by offering various options that
could be selected for end-user requirements. This chapter is written to
assist you in the proper usage of these features.
4.1 Starting Setup
The Award BIOS is immediately activated when you first power on the
computer. The BIOS reads the system information contained in the
CMOS and begins the process of checking out the system and
configuring it. When it finishes, the BIOS will seek an operating system
on one of the disks and then launch and turn control over to the
operating system.
While the BIOS is in control, the Setup program can be activated in one
of two ways:
1. By pressing <Del> immediately after switching the system
on, or
2. By pressing the <Del> key when the following message
appears briefly at the bottom of the screen during the POST
(Power On Self Test).
Press DEL to enter SETUP.
If the message disappears before you respond and you still wish to
enter Setup, restart the system to try again by turning it OFF then ON or
pressing the "RESET" button on the system case. You may also restart
by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. If you do
not press the keys at the correct time and the system does not boot, an
error message will be displayed and you will again be asked to...
PRESS F1 TO CONTINUE, DEL TO ENTER SETUP
27
4.2 Using Setup
In general, you use the arrow keys to highlight items, press <Enter> to
select, use the <PageUp> and <PageDown> keys to change entries,
press <F1> for help and press <Esc> to quit. The following table
provides more detail about how to navigate in the Setup program using
the keyboard.
Up arrow
Down arrow
Left arrow
Right arrow
Esc key
Move to previous item
Move to next item
Move to the item in the left hand
Move to the item in the right hand
Main Menu -- Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu --
Exit current page and return to Main Menu
Increase the numeric value or make changes
Decrease the numeric value or make changes
Increase the numeric value or make changes
Decrease the numeric value or make changes
General help, only for Status Page Setup Menu and Option
Page Setup Menu
PgUp key
PgDn key
+ key
- key
F1 key
(Shift)F2 key
Change color from total 16 colors. F2 to select color
forward, (Shift) F2 to select color backward
Calendar, only for Status Page Setup Menu
Reserved
Restore the previous CMOS value from CMOS, only for
Option Page Setup Menu
F3 key
F4 key
F5 key
F6 key
Load the default CMOS value from BIOS default table, only
for Option Page Setup Menu
F7 key
F8 key
F9 key
F10 key
Load the default
Reserved
Reserved
Save all the CMOS changes, only for Main Menu
4.2.1 Getting Help
Press F1 to pop up a small help window that describes the appropriate
keys to use and the possible selections for the highlighted item. To exit
the Help Window press <Esc> or the F1 key again.
28
4.3 Main Menu
Once you enter the Award BIOS CMOS Setup Utility, the Main Menu
will appear on the screen. The Main Menu allows you to select from
several setup functions and two exit choices. Use the arrow keys to
select among the items and press <Enter> to enter the sub-menu.
ROM PCI/ISA BIOS (2A69KD2L)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ꢄꢅꢆꢇ：
Select Item
(Shift)F2：Change Color
Esc：Quit
F10：Save & Exit
NOTE: A brief description of the highlighted choice appears at the bottom
of the screen.
ꢃ Standard CMOS Setup
This setup page includes all the items in a standard, AT-compatible BIOS.
ꢃ BIOS Features Setup
This setup page includes all the items of Award special enhanced features.
ꢃ Chipset Features Setup
This setup page includes all the items of chipset special features.
ꢃ Power Management Setup
This entry only appears if your system supports Power Management,
“Green PC”, standards.
ꢃ PNP/PCI Configuration Setup
This entry appears if your system supports PNP/PCI.
ꢃ Load BIOS Defaults
The BIOS defaults have been set by the manufacturer and represent
settings that provide the minimum requirements for your system to operate.
29
ꢃ Load Setup Defaults
The chipset defaults are settings that provide for maximum system
performance. While Award has designed the custom BIOS to maximize
performance, the manufacturer has the right to change these defaults to
meet their needs.
ꢃ Integrated Peripherals
This section page includes all the items of IDE hard drive and Programmed
Input / Output features.
ꢃ Set Supervisor / User Password
Change, set, or disable password. It allows you to limit access to the system
and Setup, or just to Setup.
ꢃ IDE HDD Auto Detection
Automatically detect and configure hard disk parameters. The Award BIOS
includes this ability in the event you are uncertain of your hard disk’s
parameters.
ꢃ Save & Exit Setup
Save CMOS value changes to CMOS and exit setup.
ꢃ Exit Without Saving
Abandon all CMOS value changes and exit setup.
30
4.4 Standard CMOS Setup
The Standard Setup is used for the basic hardware system
configuration. The main function is for Data/Time and Floppy/Hard Disk
Drive settings. Please refer to the following screen for the setup. When
the IDE hard disk drive you are using is larger than 528MB, you must
set the HDD mode to
mode. Please use the IDE Setup Utility in
LBA
BIOS SETUP to install the HDD correctly.
ROM PCI/ISA BIOS (2A69KD2L)
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Data (mm:dd:yy) : Fri, Dec 19 1998
Time (hh:mm:ss) : 00:00:00
TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE
:
:
:
:
Primary Master
Primary Slave
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CHS
CHS
Secondary Master
Secondary Slave
Drive A
Drive B
: 1.44M , 3.5 in.
: None
Base
Memory
:
640K
15360K
384K
LCD&CRT
Halt On
: Auto
Extended
Other
Memory
Memory
Memory
:
:
:
: All, But Keyboard
Total
16384K
ESC : Quit
F1 : Help
ꢄꢅꢆꢇ: Select Item
(Shift) F2: Change Color
PU/PD/ + / - : Modify
ꢃ
Date:
The date format is <day>, <date> <month> <year>. Press <F3> to
show the calendar.
day
The day, from Sun to Sat, determined by the BIOS and is
display-only
date
month
year
The date, from 1 to 31 (or the maximum allowed in the month)
The month, Jan through Dec.
The year, from 1900 through 2099
ꢃ
Time:
The time format is <hour> <minute> <second>. The time is
calculated based on the 24-hour military-time clock. For example,
1 p.m. is 13:00:00.
31
ꢃ
Primary Master/Slave & Secondary Master/Slave Drives:
The categories identify the types of 4 channels that have been
installed in the computer. There are 45 predefined types with 4
user-definable types for Enhanced IDE BIOS. Type 1 to Type 45
are predefined. Type user is user-definable.
Press PgUp or PgDn to select a numbered hard disk type or type
the number and press <Enter>. Note that the specifications of
your drive must match with the drive table. The hard disk will not
work properly if you enter improper information for this category. If
your hard disk drive type is not matched or listed, you can use
Type “User” to define your own drive type manually.
If you select Type “User”, you will need to know the information
listed below. Enter the information directly from the keyboard and
press <Enter>. This information should be included in the
documentation from your hard disk vendor or the system
manufacturer.
If the controller of HDD interface is ESDI, the selection shall be
“Type 1”.
If the controller of HDD interface is SCSI, the selection shall be
“None”.
If you select Type ”Auto”, BIOS will Auto-Detect the HDD &
CD-ROM Drive at the POST stage and showing the IDE for HDD
& CD-ROM Drive.
If a hard disk has not been installed select NONE and press
<Enter>.
TYPE
CYLS.
HEADS
PRECOMP
LANDZONE
SECTORS
MODE
drive type
number of cylinders
number of heads
write precompensation
landing zone
number of sectors
mode type
ꢃ
Drive A / Drive B:
The category identifies the types of floppy disk drive A or drive B
that have been installed in the computer.
None
No floppy drive installed
360K, 5.25 in
1.2M, 5.25 in
5-1/4 inch PC-type standard drive; 360 kilobyte capacity
5-1/4 inch AT-type high-density drive; 1.2 megabyte
capacity
720K, 3.5 in
1.44M, 3.5 in
2.88M, 3.5 in
3-1/2 inch double-sided drive; 720 kilobyte capacity
3-1/2 inch double-sided drive; 1.44 megabyte capacity
3-1/2 inch double-sided drive; 2.88 megabyte capacity
32
ꢃ
LCD&CRT:
The category selects the type of video adapter used for the
system monitor. Although secondary monitors are supported, you
do not have to select the type in Setup.
BOTH
LCD
CRT
Enables display of both CRT and LCD
Enables display of LCD displays only
Enables display of CRT displays only
Auto detects the installed display on the system
Auto
ꢃ
Halt On: The category determines whether the computer will stop if an
error is detected during power up.
No errors
The system boot will not be stopped for any error that
may be detected.
All errors
Whenever the BIOS detects a non-fatal error the
system will be stopped and you will be prompted.
The system boot will not stop for a keyboard error; it will
stop for all other errors.
The system boot will not stop for a disk error; it will stop
for all other errors.
All,
But Keyboard
All, But
Diskette
All, But
Disk/Key
The system boot will not stop for a keyboard or disk
error; it will stop for all other errors.
ꢃ
Memory:
The category is display-only that is determined by POST (Power
On Self Test) of the BIOS.
ꢀ Base Memory: The POST will determine the amount of base
(or conventional) memory installed in the
system. The value of the base memory is
typically 512K for systems with 512K memory
installed on the motherboard, or 640K for
systems with 640K or more memory installed
on the motherboard.
ꢀ Extended Memory: The BIOS determines how much extended
memory is present during the POST. This is
the amount of memory located above 1MB
in the CPU's memory address map.
ꢀ Total Memory: This refers to the memory located in the 640K
to 1024K address space. This is memory that
can be used for different applications. DOS
uses this area to load device drivers in an effort
to keep as much base memory free for
application programs. The BIOS is the most
frequent user of this RAM area since this is
where it shadows RAM
33
4.5 BIOS Features Setup
This section allows you to configure your system for the basic
operation. You have the opportunity to select the system’s default
speed, boot-up sequence, keyboard operation, shadowing and
security.
ROM PCI/ISA BIOS (2A69KD2L)
BIOS FEATURES SETUP
AWARD SOFTWARE, INC.
Virus Warning
CPU Internal Cache
External Cache
CPU L2 Cache ECC Checking
Processor Number Feature
Quick Power On Self Test
Boot from LAN First
Boot Sequence
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
PS/2 mouse function control
PCI/VGA Palette Snoop
OS Select For DRAM > 64MB
Report No FDD For WIN 95
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Disabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
A,C,SCSI
Disabled
Enabled
On
Fast
Disabled
6
250
Setup
Video BIOS
Shadow
Shadow
Shadow
Shadow
Shadow
Shadow
Shadow
:
:
:
:
:
:
:
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
C8000-CBFFF
CC000-CFFF
D0000-D3FFF
D4000-D7FFF
D8000-DBFFF
DC000-DFFFF
ꢄꢅꢆꢇ
PU/PD/+/-: Modify
ESC
: Quit
: Help
: Select Item
Enabled
Disabled
Non-OS2
Yes
F1
F5
F6
F7
: Old Values (Shift) F2 : Color
: Load BIOS Defaults
: Load Setup Defaults
ꢃ
Virus Warning:
When this item is enabled, the Award BIOS will monitor the boot
sector and partition table of the hard disk drive for any attempt at
modification. If an attempt is made, the BIOS will halt the system
and the following error message will appear. Afterwards, if
necessary, you will be able to run an anti-virus program to locate
and remove the problem before any damage is done.
! WARNING !
Disk boot sector is to be modified
Type "Y" to accept write or "N" to abort write
Award Software, Inc.
Enabled
Activates automatically when the system boots up causing a
warning message to appear when anything attempts to access
the boot sector or hard disk partition table.
Disabled
No warning message will appear when anything attempts to
access the boot sector or hard disk partition table.
34
NOTE: Many disk diagnostic programs that attempt to access the boot
sector table can cause the above warning message. If you will be
running such a program, we recommend that you first disable
Virus Protection beforehand.
ꢃ
CPU Internal Cache/External Cache:
These two categories speed up memory access. However, it
depends on CPU/chipset design. The default value is en able.
Enabled
Disabled
Enable cache
Disable cache
ꢃ
ꢃ
CPU L2 Cache ECC Checking:
This item allows you to enable/disable CPU L2 Cache ECC
checking. The available choices are Enabled, Disabled.
Processor Number Feature:
This option allows the system to automatically detect and display
the Pentium III microprocessor installed. When enabled, this
option is only available when using Pentium III chips.
ꢃ
Quick Power On Self Test:
This category speeds up Power On Self Test (POST) after you
power up the computer. If it is set to Enable, BIOS will shorten or
skip some check items during POST.
Enabled
Disabled
Enable quick POST
Normal POST
ꢃ
ꢃ
Boot from LAN First:
When Enabled, the BIOS attempts to boot from a LAN boot
image before it attempts to boot from a local storage
device.
Boot Sequence:
This category determines which drive to search first for the disk
operating system (i.e., DOS). The available options are:
ꢀA, C, SCSI
ꢀC, S, SCSI
ꢀ
ꢀ
SCSI, C, A
C only
ꢀC, CD-ROM, A ꢀ LS, C
ꢀCD-ROM, C, A ꢀ Zip100, C
ꢀD, A, SCSI
ꢀE, A, SCSI
ꢀF, A, SCSI
ꢀSCSI, A, C
ꢀ
ꢀ
ꢀ
ꢀ
USB-FDD, C
USB-Zip, C
USB-CD, C
USB-HDD, C
ꢃ
Swap Floppy Drive:
This item allows you to determine whether enable the swap floppy
drive or not. The available choices are Enabled/Disabled.
35
ꢃ
Boot Up Floppy Seek:
During POST, BIOS will determine if the floppy disk drive installed
is 40 or 80 tracks. 360K type is 40 tracks while 760K, 1.2M and
1.44M are all 80 tracks.
Enabled
BIOS searches for floppy disk drive to determine if it is 40 or
80 tracks. Note that BIOS cannot tell from 720K, 1.2M or
1.44M drive type as they are all 80 tracks.
Disabled
BIOS will not search for the type of floppy disk drive by track
number. Note that there will not be any warning message if
the drive installed is 360K.
ꢃ
ꢃ
Boot Up NumLock Status:
This allows you to determine the default state of the numeric
keypad. By default, the system boots up with NumLock on.
On
Off
Keypad is number keys
Keypad is arrow keys
Gate A20 Option:
This entry allows you to select how the gate A20 is handled. The
gate A20 is a device used to address memory above 1 Mbytes.
Initially, the gate A20 was handled via a pin on the keyboard.
Today, while keyboards still provide this support, it is more
common, and much faster, for the system chipset to provide
support for gate A20.
Normal
Fast
keyboard
chipset
ꢃ
Typematic Rate Setting:
This determines if the typematic rate is to be used. When
disabled, continually holding down a key on your keyboard will
generate only one instance. In other words, the BIOS will only
report that the key is down. When the typematic rate is enabled,
the BIOS will report as before, but it will then wait a moment, and,
if the key is still down, it will begin the report that the key has been
depressed repeatedly. For example, you would use such a feature
to accelerate cursor movements with the arrow keys.
Enabled
Disabled
Enable typematic rate
Disable typematic rate
36
ꢃ
Typematic Rate (Chars/Sec):
When the typematic rate is enabled, this selection allows you
select the rate at which the keys are accelerated.
6
8
6 characters per second
8 characters per second
10 characters per second
12 characters per second
15 characters per second
20 characters per second
24 characters per second
30 characters per second
10
12
15
20
24
30
ꢃ
Typematic Delay (Msec):
When the typematic rate is enabled, this selection allows you to
select the delay between when the key was first depressed and
when the acceleration begins.
250
500
750
250 msec
500 msec
750 msec
1000 msec
1000
ꢃ
Security Option:
This category allows you to limit access to the system and Setup,
or just to Setup.
System
The system will not boot and access to Setup will be denied if
the correct password is not entered at the prompt.
The system will boot, but access to Setup will be denied if the
correct password is not entered at the prompt.
Setup
NOTE: To disable security, select PASSWORD SETTING at Main Menu
and then you will be asked to enter password. Do not type anything
and just press <Enter>, it will disable security. Once the security is
disabled, the system will boot and you can enter Setup freely.
ꢃ
PS/2 Mouse Function Control:
This lets you enable or disable the hardware PS/2 mouse function
onboard.
ꢃ
PCI/VGA Palette Snoop:
It determines whether the MPEG ISA/VESA VGA Cards can work
with PCI/VGA or not.
Enabled
Disabled
When PCI/VGA working with MPEG ISA/VESA VGA Card
When PCI/VGA not working with MPEG ISA/VESA VGA Card
ꢃ
OS Select For DRAM > 64MB:
This item allows you to access the memory that over 64MB in
OS/2. The available choices are Non-OS2, OS2.
37
ꢃ
ꢃ
Report No FDD For WIN 95:
Whether report no FDD for Win 95 or not. The available choices
are Yes, No.
Video BIOS Shadow:
Determines whether video BIOS will be copied to RAM. However,
it is optional depending on chipset design. Video Shadow will
increase the video speed.
Enabled
Disabled
Video shadow is enabled
Video shadow is disabled
ꢃ
C8000 - CBFFF Shadow/D0000 - DFFFF Shadow:
These categories determine whether option ROMs will be copied
to RAM. An example of such option ROM would be support of
on-board SCSI.
Enabled
Disabled
Optional shadow is enabled
Optional shadow is disabled
38
4.6 Chipset Features Setup
This section allows you to configure the system based on the specific
features of the installed chipset. This chipset manages bus speeds and
the access to the system memory resources, such as DRAM and the
external cache. It also coordinates the communications between the
conventional ISA and PCI buses. It must be stated that these items
should never be altered. The default settings have been chosen
because they provide the best operating conditions for your system.
You might consider and make any changes only if you discover that the
data has been lost while using your system.
ROM PCI/ISA BIOS (2A69KD2L)
CHIPSET FEATURES SETUP
AWARD SOFTWARE, INC.
Auto Configuration
: Enabled
: 60ns
: 2
: 1
: 3
Power-Supply Type
Auto Detect DIMM/PCI Clk
Spread Spectrum
CPU Host Clock (CPU/PCI)
CPU Warning Temperature
Current CPU Temperature
Shutdown Temperature
:
:
:
:
:
Auto
EDO DRAM Speed Selection
EDO CASx# MA Wait State
EDO RASx# Wait State
SDRAM RAS-to-CAS Delay
SDRAM RAS Precharge Time
SDRAM CAS latency Time
SDRAM Precharge Control
DRAM Data Integrity Mode
System BIOS Cacheable
Video BIOS Cacheable
Video RAM Cacheable
8 Bit I/O Recovery Time
16 Bit I/O Recovery Time
Memory Hole At 15M-16M
Passive Release
Enabled
Disabled
Default
Disabled
: 3
: 2
:
Disabled
: Enabled
: Non-ECC
: Enabled
: Enabled
: Enabled
: 3
: 2
: Disabled
: Enabled
: Disabled
: 64
ꢄꢅꢆꢇ
PU/PD/+/-: Modify
(Shift) F2 : Color
ESC : Quit
: Select Item
Delayed Transaction
AGP Aperture Size (MB)
F1
F5
F6
F7
: Help
: Old Values
: Load BIOS Defaults
: Load Setup Defaults
ꢃ
ꢃ
Auto Configuration:
Auto Configuration selects predetermined optimal values of
chipset parameters. When Disabled, chipset parameters revert to
setup information stored in CMOS. Many fields in this screen are
not available when Auto Configuration is Enabled. The available
choices are Enabled, Disabled.
EDO DRAM Speed Selection:
The DRAM timing is controlled by the DRAM Timing Registers.
The timings programmed into this register are dependent on the
system design. Slower rates may be required in certain system
designs to support loose layouts or slower memory.
39
50ns
60ns
DRAM Timing Type
DRAM Timing Type
ꢃ
ꢃ
ꢃ
EDO CASx# MA Wait State:
You could select the timing control type of EDO DRAM CAS MA
(memory address bus). The available choices are 1, 2.
EDO RASx# Wait State:
You could select the timing control type of EDO DRAM RAS MA
(memory address bus). The available choices are 1, 2.
SDRAM RAS to CAS Delay:
You can select RAS to CAS Delay time in HCLKs of 2/2 or 3/3.
The system board designer should set the values in this field,
depending on the DRAM installed. Do not change the values in
this field unless you change specifications of the installed DRAM
or the installed CPU. The available choices are 2, 3.
ꢃ
ꢃ
SDRAM RAS Precharge Time:
Defines the length of time for Row Address Strobe is allowed to
precharge. The available choices are 2, 3.
SDRAM CAS Latency Time:
You can select CAS latency time in HCLKs of 2/2 or 3/3. The
system board designer should set the values in this field,
depending on the DRAM installed. Do not change the values in
this field unless you change specifications of the installed DRAM
or the installed CPU. The available choices are 2, 3.
ꢃ
ꢃ
ꢃ
SDRAM Precharge Control:
When enabled, all CPU cycles to SDRAM results in an All Banks
Precharge Command on the SDRAM Interface.
DRAM Data Integrity Mode:
Select Parity or ECC (error-correcting code), according to the type
of installed DRAM. The available choices are Non-ECC, ECC.
System BIOS Cacheable:
Select Enabled allows caching of the system BIOS ROM at
F000h-FFFFFh, resulting in better system performance.
However, if any program writes to this memory area, a system
error may result.
Enabled
Disabled
BIOS access cached
BIOS access not cached
ꢃ
Video BIOS Cacheable:
Select Enabled allows caching of the video BIOS ROM at
C0000h-F7FFFh, resulting in better video performance. However,
if any program writes to this memory area, a system error may
result.
40
Enabled
Disabled
Video BIOS access cached
Video BIOS access not cached
ꢃ
ꢃ
Video RAM Cacheable:
Select Enabled allows caching of the video RAM , resulting in
better system performance. However, if any program writes to this
memory area, a system error may result.
8 Bit I/O Recovery Time:
The recovery time is the length of time, measured in CPU clocks,
which the system will delay after the completion of an input/output
request. This delay takes place because the CPU is operating so
much faster than the input/output bus that the CPU must be
delayed to allow for the completion of the I/O. This item allows you
to determine the recovery time allowed for 8-bit I/O. The available
choices are from NA, 1 to 8 CPU clocks.
ꢃ
ꢃ
16 Bit I/O Recovery Time:
This item allows you to determine the recovery time allowed for
16-bit I/O. The available choices are from NA, 1 to 4 CPU clocks.
Memory Hole At 15M-16M:
In order to improve performance, certain space in memory can be
reserved for ISA cards. This memory must be mapped into the
memory space below 16 MB.
Enabled
Disabled
Memory hole supported
Memory hole not supported
ꢃ
ꢃ
ꢃ
Passive Release:
When Enabled, CPU to PCI bus accesses are allowed during
passive release. Otherwise, the arbiter only accepts another PCI
master access to local DRAM. The available choices are Enabled,
Disabled.
Delayed Transaction:
The chipset has an embedded 32-bit posted write buffer to
support delay transactions cycles. Select Enabled to support
compliance with PCI specification version 2.1. The available
choices are Enabled, Disabled.
AGP Aperture Size (MB):
Select the size of the Accelerated Graphics Port (AGP) aperture.
The aperture is a portion of the PCI memory address range
dedicated for graphics memory address space. Host cycles that
hit the aperture range are forwarded to the AGP without any
available choices are 16 MB, 32 MB, 64 MB, 128 MB, and 256MB.
41
ꢃ
Power-Supply Type:
This item allows you to select the type of power supply installed to
your board. The available choices are Auto (for auto-detection),
P8&P9 (for AT power supplies), and ATX (for ATX power supply).
ꢃ
ꢃ
Auto Detect DIMM/PCI Clk:
This item allows you to enable/disable auto detect DIMM/PCI
Clock. The available choices are Enabled, Disabled.
Spread Spectrum:
When the system clock generator pulses, the extreme values of
the pulse generate excess EMI. Enabling this option changes the
extreme values from spikes to flat curves, thus reducing EMI. The
available choices are Enabled, Disabled.
ꢃ
ꢃ
CPU Host Clock (CPU/PCI):
This option sets the timing combination of both CPU and PCI bus.
The available choices are 66/133MHz, 100/33MHz, and
133/33MHz.
CPU Warning Temperature:
This option sets the temperature limit of the CPU, once reached,
would yield a system alarm. Select the CPU warning temperature.
If your CPU temperature is higher than the selected temperature,
the BIOS will slow down your CPU process till the temperature is
below the CPU warning temperature then the CPU will work
normally. The available choices are 50oC/122oF, 53oC/127oF,
56oC/133oF, 60oC/140oF, 63oC/145oF, 66oC/151oF,and
70oC/158oF.
ꢃ
ꢃ
Current CPU Temperature:
This field displays the current CPU temperature, if your
computer contains a monitoring system.
Shutdown Temperature:
You may select the combination of lower and upper limits for the
system shutdown temperature IF your computer contains an
environmental monitoring system,. If the temperature extends
beyond either limits, the system will automatically shut down. The
available choices are Disabled, 60oC/100oF, 65oC/149oF,
70oC/158oF, and 75oC/167oF.
42
4.7 Power Management Setup
The Power Management Setup allows user to configure the system for
saving energy in a most effective way while operating in a manner
consistent with his own style of computer use.
ROM PCI/ISA BIOS (2A69KD2L)
POWER MANAGEMENT SETUP
AWARD SOFTWARE, INC.
ACPI function
: Enabled
: User Define
: Yes
: V/H Sync + Blank
: Standby
: 3
: Disabled
: Disabled
: Disabled
: Disabled
: 62.5%
** Reload Global Timer Events **
Power Management
PM Control by APM
Video Off Method
Video Off After
MODEM Use IRQ
Doze Mode
Standby Mode
Suspend Mode
HDD Power Down
Throttle Duty Cycle
PCI/VGAAct-Monitor
Soft-Off by PWR-BTTN
IRQ3 [3-7, 9-15], NMI
Primary IDE0
Primary IDE1
Secondary IDE0
Secondary IDE1
Floppy Disk
:
:
:
:
:
:
:
:
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Serial Port
Parallel Port
: Disabled
: Instant-Off
CPUFAN Off In Suspend : Disabled
Power On by Ring
Wake Up On LAN
IRQ8 Break Suspend
: Disabled
: Disabled
: Disabled
ꢄꢅꢆꢇ
: Select Item
PU/PD/+/-: Modify
(Shift) F2 : Color
ESC : Quit
F1
F5
F6
F7
: Help
: Old Values
: Load BIOS Defaults
: Load Setup Defaults
ꢃ
ACPI function:
This item allows you to enable/disable the Advanced
Configuration and Power Management (ACPI). The available
choices are Enabled, Disabled.
43
ꢃ
Power Management:
This category allows you to select the type (or degree) of power
saving and is directly related to the following modes:
ꢀ
ꢀ
Doze Mode
ꢀ
ꢀ
Suspend Mode
Standby Mode
HDD Power Down
There are four selections for Power Management, three of which have
fixed mode settings.
Disable
(default)
Min.
Power
Saving
Max.
Power
Saving
User
No power management. Disables all four modes
Minimum power management. Doze Mode = 1 hr. Standby
Mode = 1 hr., Suspend Mode = 1 hr., and HDD Power Down =
15 min.
Maximum power management -- ONLY AVAILABLE FOR SL
CPU’S. Doze Mode = 1 min., Standby Mode = 1 min., Suspend
Mode = 1 min., and HDD Power Down = 1 min.
Allows you to set each mode individually. When not disabled,
each range is from 1 min. to 1 hr. except for HDD Power Down
that ranges from 1 min. to 15 min. and disable.
Defined
ꢃ
ꢃ
PM Control by APM:
When enabled, an Advanced Power Management device will be
activated to enhance the Max. Power Saving mode and stop the
CPU internal clock. If the Max. Power Saving is not enabled, this
will be preset to No.
Video Off Method:
This determines the manner in which the monitor is blanked.
V/H SYNC+Blank
This selection will cause the system to turn off the
vertical and horizontal synchronization ports and
write blanks to the video buffer.
Blank Screen
DPMS
This option only writes blanks to the video buffer.
Initial display power management signaling.
ꢃ
Video Off After:
When enabled, this feature allows the VGA adapter to operate in a
power saving mode.
N/A
Suspend
Monitor will remain on during power saving modes.
Monitor blanked when the systems enters the Suspend
mode.
Standby
Doze
Monitor blanked when the system enters Standby mode.
Monitor blanked when the system enters any power
saving mode.
44
ꢃ
MODEM Use IRQ:
This item determines the IRQ in which the MODEM can be used.
The available choices are 3, 4, 5, 7, 9, 10, 11, NA.
4.7.1 PM Timers
The following four modes are Green PC power saving functions that
are only user configurable when User Defined Power Management has
been selected. See above for available selections.
ꢃ
ꢃ
Doze Mode:
When enabled and after the set time of system inactivity, the CPU
clock will run at slower speed while all other devices still operate at
full speed.
Standby Mode:
When enabled and after the set time of system inactivity, the fixed
disk drive and the video would be shut off while all other devices
still operate at full speed.
ꢃ
ꢃ
Suspend Mode:
When enabled and after the set time of system inactivity, all
devices except the CPU will be shut off.
HDD Power Down:
When enabled and after the set time of system inactivity, the hard
disk drive will be powered down while all other devices remain
active.
ꢃ
Throttle Duty Cycle:
When the system enters Doze mode, the CPU clock runs only part
of the time. You may select the percent of time that the clock runs.
The available choices are 12.5%, 25.0%, 37.5%, 50.0%, 62.5%,
and 75.0%
ꢃ
ꢃ
PCI/VGA Act-Monitor:
When Enabled, any video activity restarts the global timer for
Standby mode. The available choices are Enabled, Disabled.
Soft-Off by PWR-BTTN:
When Enabled, turning the system off with the on/off button
places the system in a very low-power-usage state, with only
enough circuitry receiving power to detect power button activity or
Resume by Ring activity. The available choices are Instant-Off,
Delay 4 Sec.
ꢃ
CPUFAN Off in Suspend:
When Enabled, the CPU fan turns off during Suspend
mode.
45
ꢃ
PowerOn by Ring:
An input signal on the serial Ring Indicator (RI) line (in other
words, an incoming call on the modem) awakens the system from
a soft off state. The available choices are Enabled, Disabled.
ꢃ
ꢃ
Wake Up On LAN:
An input signal on the local area network (LAN) awakens the
system from a soft off state.
IRQ 8 Break Suspend:
You can Enable or Disable monitoring of IRQ8 so it does not
awaken the system from Suspend mode. The available choices
are Enabled, Disabled.
4.7.2 Reload Global Timer Events
When Enabled, an event occurring on each device listed below restarts
the global time for Standby mode.
ꢃ
ꢃ
ꢃ
Parallel Port IRQ[3-7,9-15], NMI ꢃ Floppy Disk
Primary IDE 0/1
ꢃ
ꢃ
Serial Port
Secondary IDE 0/1
Parallel Port
46
4.8 PNP/PCI Configuration
This section describes configuring the PCI bus system. PCI, or
Personal Computer Interconnect, is a system that allows I/O devices to
operate at speeds nearing the speed the CPU itself uses when
communicating with its own special components. This section covers
some very technical items and it is strongly recommended that only
experienced users should make any changes to the default settings.
ROM PCI/ISA BIOS (2A69KD2L)
PNP/PCI CONFIGURATION
AWARD SOFTWARE, INC.
PnP OS Installed
Resources Controlled by
Reset Configuration Data
:
:
:
Yes
Auto
Disabled
Assign IRQ For VGA
: Enabled
: Enabled
Assign IRQ For USB
ꢄꢅꢆꢇ
ESC : Quit
: Select Item
F1
F5
F6
F7
: Help
: Old Values
: Load BIOS Defaults
: Load Setup Defaults
PU/PD/+/-: Modify
(Shift) F2 : Color
ꢃ
ꢃ
PnP OS Installed:
This item allows you to determine install PnP OS or not. The
available choices are Yes or Not.
Resources Controlled by:
The Award Plug and Play BIOS has the capacity to automatically
configure all of the boot and Plug and Play compatible devices.
However, this capability means absolutely nothing unless you are
using a Plug and Play operating system such as Windows 95.
The available choices are Auto and Manual.
ꢃ
Reset Configuration Data:
This item allows you to determine reset the configuration data or
not. The available choices are Enabled and Disabled.
47
ꢃ
Assign IRQ For VGA/USB:
This option turns on or off the IRQ assignment for both VGA and
USB ports.
4.9 Load BIOS Defaults
When you press <Enter> on this item you will get a confirmation dialog
box with a message shown below. This option allows you to
load/restore the BIOS default values permanently stored in the BIOS
ROM. Pressing ‘Y’ loads the BIOS default values for the most stable,
minimal-performance system operations.
ROM PCI/ISA BIOS (2A69KD2L)
LOAD BIOS DEFAULTS
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PCI CONFIGURATION S
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
Esc : Quit
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
ETUP
Load BIOS Defaults (Y/N)? N
SAVING
ꢄꢅꢆꢇ
: Select Item
F10 : Save & Exit Setup
(Shift) F2 : Change Color
Load BIOS Defaults except Standard CMOS Setup
48
4.10 Load Setup Defaults
When you press <Enter> on this item you get a confirmation dialog box
with a message similar to the figure below. This option allows you to
load/restore the default values to your system configuration, optimizing
and enabling all high performance features. Pressing ‘Y’ loads the
default values that are factory settings for optimal performance system
operations.
ROM PCI/ISA BIOS (2A69KD2L)
LOAD SETUP DEFAULTS
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PCI CONFIGURATION S
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
Esc : Quit
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
ETUP
Load SETUP Defaults (Y/N)? N
SAVING
ꢄꢅꢆꢇ
: Select Item
F10 : Save & Exit Setup
(Shift) F2 : Change Color
Load BIOS Defaults except Standard CMOS Setup
49
4.11 Integrated Peripherals
The IDE hard drive controllers can support up to two separate hard
drives. These drives have a master/slave relationship that is
determined by the cabling configuration used to attach them to the
controller. Your system supports two IDE controllers--a primary and a
secondary--so you can install up to four separate hard disks.
PIO means Programmed Input/Output. Rather than having the BIOS
issue a series of commands to affect the transfer to or from the disk
drive, PIO allows the BIOS to tell the controller what it wants and then
let the controller and the CPU perform the complete task by them. This
is much simpler and more efficient (also faster).
ROM PCI/ISA BIOS (2A69KD2L)
INTEGRATED PERIPHERALS
AWARD SOFTWARE, INC.
IDE HDD Block Mode
: Enabled
RXD , TXD Active
IR Transmission delay
Onboard Parallel Port:
Parallel Port Mode:
ECP Mode Use DMA
EPP Mode Select
:
:
:
:
:
:
:
Hi, Hi
Disabled
378/IRQ7
SPP
3
IDE Primary Slave UDMA
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
: Auto
EPP 1.7
Panel 5
: Enabled
: Enabled
: Enabled
: Enabled
: Disabled
: PCI Slot
LCD Panel Type
On-Chip Primary
PCI IDE
On-Chip Secondary PCI IDE
USB Keyboard Support
Init Display First
KBC input clock
: 8MHz
ꢄꢅꢆꢇ
: Select Item
PU/PD/+/-: Modify
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
UART2 Duplex mode
: Enabled
: 3F8/IRQ4 F1
: 2F8/IRQ3 F5
: Normal
: Full
ESC : Quit
: Help
: Old Values (Shift) F2 : Color
: Load BIOS Defaults
: Load Setup Defaults
F6
F7
ꢃ
ꢃ
IDE HDD Block Mode:
This allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive (HDD).
Enabled
Disabled
IDE controller uses block mode
IDE controller uses standard mode
IDE Primary/Secondary Master/Slave UDMA:
Ultra DMA/33 is possible only if your IDE drive supports it and the
operating environment includes a DMA driver (Windows 95 OSR2
or a third-party IDE bus master driver). If your hard drive/system
software both support Ultra DMA/33, select Auto to enable BIOS
support.
50
ꢃ
ꢃ
On-Chip Primary/Secondary PCI IDE:
The integrated peripheral controller contains an IDE interface that
supports a single IDE channels. Select Enabled to activate the
channel.
USB Keyboard Support:
Select Enabled if your system contains a Universal Serial Bus
(USB) controller and you have a USB keyboard. The available
choices are Enabled, Disabled.
ꢃ
ꢃ
ꢃ
Init Display First:
This item allows you to decide to active whether PCI Slot or
on-chip VGA first The available choices are PCI Slot, Onboard .
KBC Input Clock:
The input clock setting of your onboard keyboard controller is set
from here.
Onboard FDC Controller:
Select Enabled if your system has a floppy disk controller (FDC)
installed on the system board and you wish to use it. If you install
and-in FDC or the system has no floppy drive, select Disabled in
this field. The available choices are Enabled, Disabled.
ꢃ
ꢃ
Onboard Serial Port 1/2:
This item allows you to determine access onboard serial port 1/2
controller with which I/O address. The available choices are
3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto.
UART Mode Select:
This option allows you to configure the infrared interface modes
(IrDA, ASKIR (an IrDA-compliant serial infrared) port, and
Normal) generated from the second serial port. Only when set to
ASKIR mode will the options RxD. TxD Active and IR
Transmission delay activate for configuration. Disabling the
Onboard Serial Port 2 setting automatically removes the UART
Mode Select option from the options list.
ꢃ
ꢃ
UART2 Duplex mode:
Select the value required by the IR device connected to the IR
port. Full-duplex mode permits simultaneous two-direction
transmission. Half-duplex mode permits transmission in one
direction only at a time. The available choices are Half, Full.
RxD, TxD Active:
This item allows you to determine the active of RxD, TxD. The
available choices are “Hi, Hi”, “Lo, Lo”, “Lo, Hi”, “Hi, Lo”.
51
ꢃ
IR Transmission delay:
Full duplex mode permits simultaneous bi-directional
transmission. Half duplex mode permits transmission in one
direction only at a time. Select Disabled if there is no infrared port
present.
ꢃ
ꢃ
Onboard Parallel Port:
Select a logical LPT port name and matching address for the
physical parallel (printer) port. The available choices are
378H/IRQ7, 278H/IRQ5, 3BCH/IRQ7, Disabled.
Parallel Port Mode:
Select an operating mode for the onboard parallel port. Select
Compatible or Extended unless you are certain both your
hardware and software support EPP or ECP mode. The available
choices are SPP, ECP+EPP1.7, EPP1.7+SPP, EPP1.9+SPP,
ECP, ECP+EPP1.9, and Normal.
ꢃ
ꢃ
ECP Mode Use DMA:
Select a DMA channel for the port. The available choices are 3, 1.
EPP Mode Select:
This item allows you to determine the IR transfer mode of onboard
I/O chip. The available choices are EPP1.9, EPP1.7.
ꢃ
LCD Panel Type:
This option allows you to select the panel display type and
resolution installed on your system.
Panel#
Panel Type
0
1
1024*768 Dual Scan STN Color Panel
128*1024 TFT Color Panel
2
3
4
640*480 Dual Scan STN Color Panel
800*600 Dual Scan STN Color Panel
640*480 Sharp TFT Color Panel
5
640*480 18-bit TFT Color Panel
6
1024*768 TFT Color Panel
7
800*600 TFT Color Panel
8
9
800*600 TFT Color Panel (Large BIOS ONLY)
800*600 TFT Color Panel (Large BIOS ONLY)
800*600 Dual Scan STN Color Panel (Large BIOS ONLY)
800*600 Dual Scan STN Color Panel (Large BIOS ONLY)
1024*768 TFT Color Panel (Large BIOS ONLY)
1280*1024 Dual Scan STN Color Panel (Large BIOS ONLY)
1024*600 Dual Scan STN Color Panel (Lange BIOS ONLY)
1024*600 TFT Color Panel (Lange BIOS ONLY)
10
11
12
13
14
15
52
4.12 Supervisor/User Password Setting
ROM PCI/ISA BIOS (2A69KD2L)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURA
LOAD BIOS DEFAULT
LOAD SETUP DEFAULTS
Esc : Quit
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
ETUP
Enter Password :
SAVING
ꢄꢅꢆꢇ
: Select Item
F10 : Save & Exit Setup
(Shift) F2 : Change Color
Change / Set / Disable Password
You can set either supervisor or user password, or both of then. The
differences between are:
ꢃ
supervisor password: can enter and change the options of the setup
menus.
ꢃ
user password: just can only enter but do not have the right to change the
options of the setup menus.
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
ENTER PASSWORD:
Type the password, up to eight characters in length, and press
<Enter>. The password typed now will clear any previously entered
password from CMOS memory. You will be asked to confirm the
password. Type the password again and press <Enter>. You may
also press <Esc> to abort the selection and not enter a password.
To disable a password, just press <Enter> when you are prompted to
enter the password. A message will confirm the password will be
disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
PASSWORD DISABLED.
53
When a password has been enabled, you will be prompted to enter it
every time you try to enter Setup. This prevents an unauthorized
person from changing any part of your system configuration.
Additionally, when a password is enabled, you can also require the
BIOS to request a password every time your system is rebooted. This
would prevent unauthorized use of your computer.
You determine when the password is required within the BIOS
Features Setup Menu and its Security option (see Section 3). If the
Security option is set to “System”, the password will be required both at
boot and at entry to Setup. If set to “Setup”, prompting only occurs
when trying to enter Setup.
4.13 IDE HDD Auto Detection
This option detects the parameters of an IDE hard disk drive, and
automatically enters them into the Standard CMOS Setup screen.
Up to four IDE drives can be detected, with parameters for each
appearing in sequence inside a box. To accept the displayed entries,
press the “Y” key; to skip to the next drive, press the “N” key. If you
accept the values, the parameters will appear listed beside the drive
letter on the screen.
ROM PCI/ISA BIOS (2A69KD2L)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
HARD DISKS
TYPE SIZE CYLS
HEAD
PRECOMP LANDZ SECTOR MODE
Primary Master:
Select Primary Master Option (N=SKIP) : N
OPTIONS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR
1 (Y)
MODE
0
0
0
0
0
0
0
NORMAL
NOTE: Some OSes (like SCO-UNIX) must use ”NORMAL” for installation
54
4.14 Save & Exit Setup
Pressing <Enter> on this item asks for confirmation:
Pressing “Y” stores the selections made in the menus in CMOS – a
special section of memory that stays on after you turn your system off.
The next time you boot your computer, the BIOS configures your
system according to the Setup selections stored in CMOS. After saving
the values the system is restarted again.
ROM PCI/ISA BIOS (2A69KD2L)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURA
LOAD BIOS DEFAULT
LOAD SETUP DEFAULTS
Esc : Quit
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
ETUP
SAVE to CMOS and EXIT (Y/N)? N
SAVING
ꢄꢅꢆꢇ
: Select Item
F10 : Save & Exit Setup
(Shift) F2 : Change Color
Saves all Data & Exit Setup
55
4.15 Exit Without Saving
Pressing <Enter> on this item asks for confirmation:
Quit without saving (Y/N)? Y
This allows you to exit Setup without storing in CMOS any change. The
previous selections remain in effect. This exits the Setup utility and
restarts your computer.
ROM PCI/ISA BIOS (2A69KD2L)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURA
LOAD BIOS DEFAULT
LOAD SETUP DEFAULTS
Esc : Quit
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
ETUP
Quit Without Saving (Y/N)? N
SAVING
ꢄꢅꢆꢇ
: Select Item
F10 : Save & Exit Setup
(Shift) F2 : Change Color
Abandon all Data & Exit Setup
56
Chapter 5
Software Utilities
This chapter contains the detailed information of IDE, VGA, Audio and
LAN driver installation procedures.
5.1 VGA Driver Installation for Win
95/98
1. Click Start, then Setting, then Control Panel.
2. Start the Display applet program.
57
3. Select the setting page, click on the Advanced properties
button.
4. Press the Change button in the adapter area.
5. Click on Next to continue and then select
Display a list of all drivers in a specific location,
so you can select the drivers you want.
6. Click on Next.
7. Select the Specify a location checkbox then Browse.
8. Specify the path to the new driver and then press the <ENTER>
key (if in driver A: select a:\win95).
9. Once completed, the Select device dialog box will appear.
Choose on:
Chips and Tech. 69000 PCI
10. Continue choosing until asked to restart machine.
58
11. After the system has restarted, you can go back into the display
applet and select alternate screen resolutions and color depths.
NOTE: Installation procedure for Windows 98 is similar to Windows95.
5.2 VGA Driver Installation for Win
NT4.0
1. Click the Start button, then go to Settings and click on Control
Panel.
2. Click on Display icon to start the Display Properties window.
3. Click on the Settings tab, and then click on Display Type.
59
4. In the Change Display Type window, click on Have Disk.
5. Specify the path to the new driver and press the <ENTER>key
(if in driver A:, type a:\nt40). Select
Chips Video Accelerator
(655545/48/50/54/55/68554 69000)
6. Click OK or press Enter.
7. You will then see warning panel about Third Party Drivers. Click
on Yes to complete installation.
8. Once the installation is complete, the system must be shut down
and restarted for the new driver to take effect.
60
9. After restarting, check on the VGA driver and make sure the
properties of the driver look similar to the following figure.
61
5.3 LAN Driver Installation for WIN95 &
WIN98
5.3.1 Win98
Windows 98 will detect the network driver automatically therefore there
is no need for further configuration.
5.3.2 Win95
1. Click Start, then Setting then select Control panel.
2. Start the network applet program.
3. In the Network window, click Add.
4. From the Select Network Component Type, select Adapter then
click Add.
62
5. Specify the path the new driver and press <ENTER> key (if in
driver a:, type a:\). If you’re not sure exactly where the drivers
are, choose the Browse button and find it.
6. Click OK.
7. Windows 95 will copy the network drivers to the proper
directories into your system.
8. Continue choosing OK until asked to restart your system.
9. After restarting your computer, check the network driver and its
properties. Be sure it looks similar with the following figure.
63
5.4 LAN Driver Installation for Win
NT4.0
1. Click the Start button, then go to Setting and click on Control
Panel.
2. Click on the Network icon to start the Network Window.
3. Click on the Adapters tab, and then click Add.
4. In the Select Network Adapter window, click Have Disk.
5. This will bring up the Insert Disk window.
6. Supply the directory where the Windows NT driver files are
located (If in driver a: type a:\).
7. The Select OEM Option window will show up. Select
Intel EtherExpress PRO Adapter
8. Click OK to finish the installation.
64
9. Once the installation is completed, the system must be shut
down and restarted for the new driver to take effect.
10.After restart, confirm the network driver and its properties.
65
This page intentionally left blank.
66
|