|
IB865
LGA775 Pentium 4
Intel 865G Chipset
Full Size CPU Card
USER’S MANUAL
Version 1.0
Table of Contents
Introduction....................................................... 1
Checklist .......................................................................... 1
Product Description .......................................................... 2
Specifications ................................................................... 3
Board Dimensions............................................................. 4
Installations....................................................... 5
Installing the CPU ............................................................ 6
ATX Power Installation .................................................... 7
Installing the Memory....................................................... 7
Setting the Jumpers........................................................... 8
Connectors on IB865 ...................................................... 17
Watchdog Timer............................................................. 29
BIOS Setup...................................................... 31
Drivers Installation ..................................... 53
IB865 User’s Manual
iii
ATTENTION:
It is strongly recommended that only heatsinks that have corresponding
(metal) backplates are used on the CPU card. This is to avoid the CPU
card being bent/distorted, causing the CPU card to become damaged. A
reference picture of a backplate and heatsink that has backplate are
shown below.
iv
IB865 User’s Manual
INTRODUCTION
Introduction
Checklist
Your IB865 Pentium 4CPU card package should include the items listed
below:
·
·
·
·
·
·
·
The IB865 CPU Card
This User’s Manual
1 IDE Ribbon Cable
1 Floppy Ribbon Connector
SATA Power Cord
SATA Cable
2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a
Mounting Bracket
·
·
1 Y-Cable supporting a PS/2 Keyboard and a PS/2 Mouse
1 CD containing the following:
·
·
Chipset Drivers
Flash Memory Utility
·
·
·
Optional audio cable with bracket (Audio8K)
Optional USB cable with bracket (USB2K-4)
Optional Secondary CRT VGA cable with bracket (VGA4K, for
use with IBA110)
·
Optional TMDS cable with bracket (ID120P, for use with
IBA110)
·
·
Optional TV-out cable (TVOUT-6, for use with IBA120)
Optional MicroAGP cards (IBA120, IBA110)
IB865 User’s Manual
1
INSTALLATIONS
Product Description
The IB865 Pentium 4 CPU card incorporates the Intel 865G chipset that
can utilize a LGA775 processor of up to 3.8GHz or higher and supports
FSB frequency of 533/800Mhz (133Mhz, and 200Mhz HCLK
respectively).
The 865G chipset comes with a Graphics Memory Controller Hub
(GMCH) designed for use with the Pentium 4 processor with 1MB L2
cache on 0.09 micron process. The GMCH component provides the CPU
interface, DDR interface, AGP interface, Hub Interface, and integrated
graphics with display interfaces.
Aside from CRT support, the VGA function feature a Micro AGP slot
for optional daughter cards:
IBA120: with Chrontel CH7017 chipset that supports dual channel
LVDS, TV-out interface
IBA110: with ATI M7CSP32, M9CSP64 / M10CSP64 chipset,
64MB/32MB frame buffer and supports dual channel LVDS
interface, TMDS and CRT2 display function.
The board also has one Intel 82547GI Gigabit LAN and an Intel 82551
10/100MB fast Ethernet LAN.
Other advanced features include two Serial ATA ports, four USB 2.0
ports, IrDA interface and audio function.
2
IB865 User’s Manual
INTRODUCTION
Specifications
Product Name
CPU Type
CPU Voltage
System Speed
IB865
LGA775 socket (Intel Pentium 4 / Celeron D)
0.8375V~1.6V (VRD 10.1)
2.53GHz~3.8GHz
CPU
Operating 533MHz/800MHz
Frequency
Green /APM
CPU Socket
Chipset
APM1.2
LGA 775 Socket
Intel 865G Chipset
GMCH: 82865G 932-pin FC-BGA, ICH5: 82801EB
460-pin MBGA, FWH
BIOS
Cache
MicroAGP Socket
VGA
Award BIOS; support ACPI Function
256K/1M Level 2 (CPU integrated)
Two selection: IBA110 or IBA120 Micro AGP card
Two selection :
1. 82865G built-in VGA, AGP 4X, supports with CRT +
IBA120: CH7017, for LVDS dual channel or TV-OUT.
2. MicroAGP card: IBA110: ATI Mobility M7/M9/M10
graphics controller, embedded 32/64MB Frame buffer
(DDR), AGP 4X/8X, for CRT, LVDS, TMDS, 2nd CRT
Intel 82551QM LAN controller (10/100Mb)
Intel 82547GI (10/100/1000Mb) Gigabit LAN (optional)
ICH5 Built-in Sound controller + AC97 Codec ALC655
support AC3 5.1 channel, 2x6 12-pin header
2 x DDR 2.5V DDR333/400 SDRAM( without ECC
Function) DIMM Module, Max. capacity - 2GB
Winbond 83627HF: IrDAx1, Parallel x1, COM1
(RS-232), COM2 (RS-232/RS422/RS485), FDC 1.44MB,
Hardware monitor (3 thermal inputs, 6 voltage monitor
inputs, VID0-4, 1 chassis open detection, 3 fan headers)
ICH5 built-in
Primary LAN
Secondary LAN
Audio
Memory type
LPC I/O
RTC/CMOS
Local bus IDE
Serial ATA
ICH5 built-in, IDE1, 2 (Ultra DMA 33/66/100)
2 ports
D-type Connectors
Power Connector
PCI to ISA Bridge
ISA High Drive
USB
PS/2 keyboard/mouse, VGA (CRT), RJ-45 x 2
ATX 12V
ITE 8888
Yes, SN74ABT16245
4 x USB 2.0
Watchdog Timer
System Voltages
Other Features
Form Factor
Yes ( 256 segments : 0, 1, 2,...255 sec/min)
+5V, +12V, -12V, 5VSB
Modem Wakeup, LAN Wakeup, DiskOnChip, IrDA
PICMG (full size CPU card)
Board Size
122 x 338 mm
IB865 User’s Manual
3
INSTALLATIONS
Board Dimensions
4
IB865 User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the IB865 in order to set up a workable system. The topics
covered are:
Installing the CPU ............................................................ 6
ATX Power Installation .................................................... 7
Installing the Memory....................................................... 7
Setting the Jumpers........................................................... 8
Connectors on IB865 ...................................................... 17
IB865 User’s Manual
5
INSTALLATIONS
Installing the CPU
The IB865 CPU card supports a LGA 775 processor socket for Intel®
Pentium® 4 processors.
The LGA 775 processor socket comes with a lever to secure the
processor. Refer to the pictures below, from left to right, on how to place
the processor into the CPU socket. Please note that the cover of the
LGA775 socket must always be installed during transport to avoid
damage to the socket.
6
IB865 User’s Manual
INSTALLATIONS
ATX Power Installation
The system power is provided to the CPU card with theCN1 and J7 ATX
power connectors. Please note that the J7 external ATX power connector
should be connected to the backplane for IB865 to function. J7 is a 3-pin
power connector. CN1 is a 4-pin 12V power connector. CN1 is to be
connected to the ATX power supply.
Installing the Memory
The IB865 CPU card supports two DDR memory sockets for a maximum
total memory of 2GB in DDR memory type. You can install unbuffered
& non-ECC DDR DIMMs. It supports DDR266/333 when installed with
CPUs that have clock speeds of 533MHz. It supports DDR266/320/400
when installed with CPUs that have clock speeds of 800MHz. The board
provides dual channel functionality for its DIMM slots. DIMM1 is for
one channel and DIMM2 is for the other channel. Enabling dual
channels can increase data access rates.
Basically, the system memory interface has the following features:
Supports two 64-bit wide DDR data channels
Available bandwidth up to 3.2GB/s (DDR400) for single-channel
mode and 6.4GB/s (DDR400) in dual-channel mode.
Supports non ECC DIMMs.
Supports 128Mb, 256Mb, 512Mb DDR technologies.
Supports only x8, x16, DDR devices with four banks
Registered DIMMs not supported
Supports opportunistic refresh
Up to 16 simultaneously open pages (four per row, four rows
maximum)
IB865 User’s Manual
7
INSTALLATIONS
Setting the Jumpers
Jumpers are used on IB865 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB865 and their respective functions.
Jumper Locations on IB865..........................................................9
JP1: Clear CMOS Contents........................................................10
JP2, JP3, JP4: RS232/422/485 (COM2) Selection ......................10
JP5/6/7/8/9/10/11: CRT VGA Signal Select...............................10
JP13: Primary LAN Enable/Disable...........................................11
JP14: DiskOnChip Address Select .............................................11
Jumper and Connectors on IBA120............................................12
J1: Panel Inverter Power Connector ...........................................12
JP2: Panel Voltage Setting.........................................................12
J4: TV out Connector.................................................................12
JP1: TV Type Select...................................................................13
JP2: LVDS Panel Power Select ..................................................13
J2, J3: LVDS Connectors (2nd channel, 1st channel).................13
Jumper and Connectors on IBA110............................................14
J1: TMDS Panel Connector........................................................14
J2: CRT2 / TV-Out Connector ...................................................14
J3: Panel Inverter Power Connector ...........................................15
J4: VGA Chipset Fan Power Connector .....................................15
J5, J6: LVDS Connectors (2nd channel, 1st channel).................15
JP1: LVDS Panel Power Select ..................................................15
SW1: LVDS Resolution Select...................................................16
8
IB865 User’s Manual
INSTALLATIONS
Jumper Locations on IB865
JP1: Clear CMOS Contents
JP2, JP3, JP4: RS232/422/485
(COM2) Selection
JP5/6/7/8/9/10/11: CRT VGA
Signal Select
JP13: Primary LAN Enable/Disable
JP14: DiskOnChip Address Select
Jumper Locations on IB865
IB865 User’s Manual
9
INSTALLATIONS
JP1: Clear CMOS Contents
Use JP1, a 3-pin header, to clear the CMOS contents. Note that the
ATX-power connector should be disconnected from the CPU card
before clearing CMOS.
JP1
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
JP2, JP3, JP4: RS232/422/485 (COM2) Selection
J4, COM1 is fixed for RS-232 use only.
J5, COM2 is selectable for RS232, RS-422 and RS-485.
The following table describes the jumper settings for COM2 selection.
COM2
RS-232
RS-422
RS-485
Function
JP2:
1-2
JP2:
3-4
JP2:
5-6
Jumper
Setting
JP3:
JP3:
JP3:
(pin closed) 3-5 & 4-6
1-3 & 2-4
1-3 & 2-4
JP4:
JP4:
JP4:
3-5 & 4-6
1-3 & 2-4
1-3 & 2-4
JP5/6/7/8/9/10/11: CRT VGA Signal Select
Use these seven 3-pin headers to select the VGA signal either from the
on board VGA or from the MicroAGP VGA.
JP5/6/7/8/9/10/11
Setting
Function
Pin 1-2
Short/Closed
On board VGA
Pin 2-3
Short/Closed
MicroAGP VGA
10
IB865 User’s Manual
INSTALLATIONS
JP13: Primary LAN Enable/Disable
JP13 Function
Enable LAN
Disable LAN
JP14: DiskOnChip Address Select
JP14 Address
D0000-D7FFF
D8000-DFFFF (default)
IB865 User’s Manual
11
INSTALLATIONS
Jumper and Connectors on IBA120
J1: Panel Inverter Power Connector
Pin #
Signal Name
+12V
ENABKL
Ground
1
2
3
Remarks: Maximum current is 1A.
JP2: Panel Voltage Setting
JP2
Setting
Panel Voltage
Pin 1-2
Short/Closed
3.3V
Pin 2-3
Short/Closed
5V
J4: TV out Connector
The pin assignments of the TV out connector are as follows:
Signal Name
Ground
Y
Pin Pin Signal Name
1
3
5
7
2
4
6
8
Ground
C
NC
NC
COMP
Protect pin
12
IB865 User’s Manual
INSTALLATIONS
JP1: TV Type Select
JP1
Setting
TV Type
Pin 1-2
Short/Closed
NTSC
Pin 2-3
Short/Closed
PAL
JP2: LVDS Panel Power Select
JP2
Setting
Panel Voltage
Pin 1-2
Short/Closed
3.3V (default)
Pin 2-3
Short/Closed
5V
J2, J3: LVDS Connectors (2nd channel, 1st channel)
The LVDS connectors, DF13 20-pin mating connectors, are composed
of the first channel (J2) and second channel (J3) to support 24-bit or
48-bit.
Signal Name Pin # Pin #
Signal Name
TX0+
TX0-
Ground
TX1-
2
4
6
1
3
5
Ground
TX1+
5V/3.3V
TX3-
TX2-
Ground
TXC-
5V/3.3V
+12V
8
7
9
Ground
TX3+
TX2+
Ground
TXC+
ENABKL
+12V
10
12
14
16
18
20
11
13
15
17
19
Remarks: Maximum current for +12V is 1A.
IB865 User’s Manual
13
INSTALLATIONS
Jumper and Connectors on IBA110
J1: TMDS Panel Connector
TMDS stands Transition Minimized Differential Signaling.
Signal Name Pin # Pin #
Signal Name
TX1P
TXIN
GND
GND
TXCP
TXCN
GND
+5v
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
TX2P
TX2N
GND
GND
TX0P
TX0N
NC
NC
J1
HTPG
NC
DDCDATA
DDCCLK
10
J2: CRT2 / TV-Out Connector
This connectoris used fora second CRT monitor or use with a TV output device.
Signal Name Pin # Pin #
Signal Name
+5V
Ground
N. C.
CRT2 DDCDAT
HSYNC
VSYNC
CRT2 DDCCLK
N.C.
Red / C
Green / Y
Blue / COMP
N.C.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Ground
Ground
J2
Ground
Ground
14
IB865 User’s Manual
INSTALLATIONS
J3: Panel Inverter Power Connector
The connector supports 1A current (maximum).
Pin #
Signal Name
+12V
1
2
3
NC
Ground
J4: VGA Chipset Fan Power Connector
Pin #
1
2
Signal Name
+12V
Ground
J5, J6: LVDS Connectors (2nd channel, 1st channel)
The LVDS connectors, DF13 20-pin mating connectors, are composed
of the first channel (J6) and second channel (J5) to support 24-bit or
48-bit.
Signal Name Pin # Pin #
Signal Name
TX0+
TX0-
Ground
TX1-
2
4
6
1
3
5
Ground
TX1+
5V/3.3V
TX3-
TX2-
Ground
TXC-
5V/3.3V
+12V
8
7
9
Ground
TX3+
TX2+
Ground
TXC+
ENABKL
+12V
10
12
14
16
18
20
11
13
15
17
19
Remarks: Maximum current for +12V is 1A.
JP1: LVDS Panel Power Select
JP1
Setting
Panel Voltage
Pin 1-2
Short/Closed
3.3V (default)
Pin 2-3
Short/Closed
5V
IB865 User’s Manual
15
INSTALLATIONS
SW1: LVDS Resolution Select
SW1-1
OFF
ON
SW1-2
ON
OFF
OFF
SW1-3
ON
ON
Resolution
800x600 18 bit
1024x768 18bit
1024x768 24 bit
OFF
ON
16
IB865 User’s Manual
INSTALLATIONS
[
Connectors on IB865
The connectors on IB865 allows you to connect external devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The
following table lists the connectors on IB865 and their respective
functions.
Connector Locations on IB865 .................................................. 18
IDE1, IDE2: EIDE Connectors.................................................. 20
FDD1: Floppy Drive Connector................................................. 20
CN1: ATX 12V/+12V Power Connector ................................... 20
CN2, CN3: USB Connectors ..................................................... 21
J3: CPU Fan Power Connector .................................................. 21
J7: External ATX Power Connector .......................................... 21
J8, J9: System Fan Power Connector ......................................... 21
J1: System Function Connector ................................................. 22
J2: Parallel Port Connector........................................................ 24
J4, J5: COM1 and COM2 Serial Ports Connector ...................... 24
J10: Wake On LAN Connector.................................................. 25
J11: External Audio Connector ................................................. 25
J12: CD-In Audio Connector..................................................... 25
J13, J14: Serial ATA (SATA) Connectors................................. 25
J15: VGA CRT Connector......................................................... 26
J16, J18: External PS/2 Keyboard and Mouse Connector........... 26
J17: IrDA Connector ................................................................. 26
J19: PS/2 Keyboard and Mouse Connector ................................ 27
J20: Primary RJ45 Connector .................................................... 27
J21: Gigabit LAN RJ45 Connector ............................................ 27
AGP1: MicroAGP Connector (for IBA110 / IBA120)................ 27
IB865 User’s Manual
17
INSTALLATIONS
Connector Locations on IB865
Connector Locations on IB865:
IDE1, IDE2: EIDE Connectors
FDD1: Floppy Drive Connector
CN1: ATX 12V/+12V Power
Connector
CN2, CN3: USB Connectors
J3: CPU Fan Power Connector
J7: External ATX Power Connector
J8, J9: System Fan Power Connector
J1: System Function Connector
J2: Parallel Port Connector
J4, J5: COM1 and COM2 Serial Ports
Connector
J10: Wake On LAN Connector
J11: External Audio Connector
J12: CD-In Audio Connector
J13, J14: Serial ATA (SATA)
Connectors
J15: VGA CRT Connector
J16, J18: External PS/2 Mouse and
Keyboard Connector
J17: IrDA Connector
J19: PS/2 Keyboard and Mouse
Connector
J20: Primary RJ45 Connector
J21: Gigabit LAN RJ45 Connector
AGP1: MicroAGP Connector (for
IBA110 / IBA120)
18
IB865 User’s Manual
INSTALLATIONS
IDE1, IDE2: EIDE Connectors
Signal Name
Pin #
Pin #
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
1
2
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
3
4
5
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK0
Ground
Ground
Host ALE
Ground
IRQ14
No connect
No connect
Address 2
Chip select 1
Ground
Address 1
Address 0
Chip select 0
Activity
IDE1
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
Pin #
1
Pin #
2
Signal Name
Ground
3
4
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
Ground
Ground
Host ALE
Ground
5
6
8
7
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
DRQ1
Host IOW
Host IOR
IOCHRDY
DACK1
IRQ15
No connect
No connect
Address 2
Chip select 1
Ground
IDE2
Address 1
Address 0
Chip select 0
Activity
IB865 User’s Manual
19
INSTALLATIONS
FDD1: Floppy Drive Connector
FDD1 is a 34-pin header and will support up to 2.88MB floppy drives.
Signal Name Pin # Pin #
Signal Name
RM/LC
No connect
No connect
Index
Motor enable 0
Drive select 1
Drive select 0
Motor enable 1
Direction
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
1
3
5
7
2
4
6
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
11
13
15
17
19
21
23
25
27
29
31
33
Step
Write data
Write gate
Track 00
Write protect
Read data
FDD1
Side 1 select
Diskette change
CN1: ATX 12V/+12V Power Connector
Pin #
Signal Name
Ground
Ground
+12V
1
2
3
4
+12V
20
IB865 User’s Manual
INSTALLATIONS
CN2, CN3: USB Connectors
The following table shows the pin outs of the USB pin headers
connectors. Overall, the two pin headers support four USB ports.
Signal Name Pin Pin Signal Name
Vcc
1
2
3
4
5
6
7
8
Ground
USB1+
USB1-
Vcc
USB0-
USB0+
Ground
CN2
Signal Name Pin Pin Signal Name
Vcc
1
2
3
4
5
6
7
8
Ground
USB3+
USB3-
Vcc
USB2-
USB2+
Ground
CN3
J3: CPU Fan Power Connector
J3 is a 3-pin header for the CPU fan. The fan must be a 12V fan.
Pin #
Signal Name
Ground
+12V
Rotation detection
Control
1
2
3
4
J7: External ATX Power Connector
Pin #
Signal Name
1
2
3
Ground
PS-ON (soft on/off)
5VSB (Standby +5V)
J8, J9: System Fan Power Connector
J8 and J9 are 3-pin headers for system fans. The fan must be a 12V fan.
Pin #
Signal Name
Ground
+12V
Rotation detection
1
2
3
IB865 User’s Manual
21
INSTALLATIONS
J1: System Function Connector
J1 provides connectors for system indicators that provide light
indication of the computer activities and switches to change the
computer status. J1 is a 20-pin header that provides interfaces for the
following functions.
Hard Disk Drive LED
Reset Switch
Not Defined
ATX Power On Switch
SMI / Hardware Switch
Power LED
Speaker
Speaker: Pins 1 - 4
This connector provides an interface to a speaker for audio
tone generation. An 8-ohm speaker is recommended.
Pin #
Signal Name
Speaker out
No connect
Ground
1
2
3
4
+5V
Power LED: Pins 11 - 15
The power LED indicates the status of the main power
switch.
Pin #
11
12
Signal Name
Power LED
No connect
Ground
13
14
15
No connect
Ground
22
IB865 User’s Manual
INSTALLATIONS
SMI/Hardware Switch: Pins 6 and 16
This connector supports the "Green Switch" on the control
panel, which, when pressed, will force the system into the
power-saving mode immediately.
Signal Name
SMI
Pin #
6
16
Ground
ATX Power ON Switch: Pins 7 and 17
This 2-pin connector is an “ATX Power Supply On/Off
Switch” on the system that connects to the power switch on
the case. When pressed, the power switch will force the
system to power on. When pressed again, it will force the
system to power off.
Reset Switch: Pins 9 and 19
The reset switch allows the user to reset the system without
turning the main power switch off and then on again.
Orientation is not required when making a connection to
this header.
Hard Disk Drive LED Connector: Pins 10 and 20
This connector connects to the hard drive activity LED on
control panel. This LED will flash when the HDD is being
accessed.
Pin #
10
20
Signal Name
HDD Active
5V
IB865 User’s Manual
23
INSTALLATIONS
J2: Parallel Port Connector
The following table describes the pin out assignments of this connector.
Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
ACK, acknowledge
Busy
Pin # Pin # Signal Name
1
2
14
15
16
17
18
19
20
21
22
23
24
25
N/A
AutoFeed
Error
3
4
Initialize
Select
5
6
7
8
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
N/A
9
10
11
12
13
J2
Paper empty
Select
J4, J5: COM1 and COM2 Serial Ports Connector
J4 and J5 both 10-pin headers, are the onboard serial port connectors.
J4
Pin #
Signal Name
Fixed as
RS-232
RS-232
DCD
RX
RS-422
TX-
TX+
RX+
RX-
GND
RTS-
RTS+
CTS+
CTS-
NC
RS-485
DATA-
DATA+
NC
NC
GND
NC
NC
NC
NC
NC
1
2
3
4
5
6
7
8
9
TX
J5
DTR
GND
DSR
RTS
CTS
RI
Configurable
as RS-232/
RS-422/485
with jumpers
JP2/JP3/JP4
10
NC
24
IB865 User’s Manual
INSTALLATIONS
J10: Wake On LAN Connector
J10 is a 3-pin header for the Wake On LAN function on the
motherboard. The following table shows the pin out assignments of this
connector. Wake On LAN will function properly only with an ATX
power supply with 5VSB that has 1A.
Pin #
Signal Name
+5VSB
Ground
LAN Wakeup
1
2
3
J11: External Audio Connector
J11 is a 12-pin header that is used to connect to the optional audio cable
that integrates jacks for Line In, Line Out and Mic.
Signal Name
Pin #
Pin #
Signal Name
LINEOUT_R
1
2
LINEOUT_L
Ground
3
4
Ground
LINEIN_R
Ground
5
6
LINEIN L
Ground
7
8
Mic-In
9
10
12
VREFOUT
Protect pin
Ground
11
J12: CD-In Audio Connector
Pin # Signal Name
1
2
3
4
CD Audio R
Ground
Ground
CD Audio L
J13, J14: Serial ATA (SATA) Connectors
The SATA connectors support serial ATA 150. Each connector can only
use one serial ATA hard disk. J13 is port 1 and J14 is port 2.
IB865 User’s Manual
25
INSTALLATIONS
J15: VGA CRT Connector
The pin assignments of the J15 VGA CRT connector are as follows:
Signal Name Pin Pin Signal Name
Red
Blue
1
3
2
4
Green
N.C.
GND
GND
N.C.
N.C.
HSYNC
NC
5
7
9
11
13
15
6
8
10
12
14
GND
GND
GND
N.C.
J15
VSYNC
J16, J18: External PS/2 Keyboard and Mouse Connector
Pin #
J16
KB clock
KB data
N.C.
Ground
Vcc
J18
Mouse data
N.C.
Ground
Vcc
1
2
3
4
5
Mouse clock
J17: IrDA Connector
J17 is used for an optional IrDA connector for wireless communication.
Pin #
Signal Name
+5V
No connect
Ir RX
1
2
3
4
5
Ground
Ir TX
26
IB865 User’s Manual
INSTALLATIONS
J19: PS/2 Keyboard and Mouse Connector
J19 uses a Y-cable with dual D-connectors for a PS/2 keyboard and a
PS/2 mouse.
Pin #
Signal Name
Mouse data
Keyboard data
Ground
1
2
3
4
5
6
Vcc
Mouse Clock
Keyboard Clock
J19
J20: Primary RJ45 Connector
J20 is the primary RJ-45 connector based on the chipset integrated LAN.
The figure below shows the pin out assignments of the connector and its
corresponding input jack.
J21: Gigabit LAN RJ45 Connector
J21 is the Gigabit LAN RJ45 connector.
AGP1: MicroAGP Connector (for IBA110 / IBA120)
IB865 User’s Manual
27
INSTALLATIONS
Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sort of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user
will restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
This code and information is provided "as is" without warranty of any
kind, either expressed or implied, including but not limited to the
implied warranties of merchantability and/or fitness for a particular
purpose.
;[]================================================
; Name : Enable_And_Set_Watchdog
; IN : AL - 1sec ~ 255sec
; OUT : None
;[]================================================
Enable_And_Set_Watchdog Proc Near
pushax
;save time interval
call Unlock_Chip
mov cl, 2Bh
call Read_Reg
and al, NOT 10h
call Write_Reg
;set GP24 as WDTO
mov cl, 07h
mov al, 08h
call Write_Reg
;switch to LD8
mov cl, 0F5h
call Read_Reg
and al, NOT 08h
call Write_Reg
;set count mode as second
;set watchdog timer
pop ax
mov cl, 0F6h
call Write_Reg
28
IB865 User’s Manual
INSTALLATIONS
mov al, 01h
mov cl, 30h
call Write_Reg
;watchdog enabled
call Lock_Chip
ret
Enable_And_Set_Watchdog Endp
;[]===============================================
; Name : Disable_Watchdog
; IN : None
; OUT : None
;[]===============================================
Disable_Watchdog Proc Near
call Unlock_Chip
mov cl, 07h
mov al, 08h
call Write_Reg
;switch to LD8
xor al, al
mov cl, 0F6h
call Write_Reg
;clear watchdog timer
;watchdog disabled
xor al, al
mov cl, 30h
call Write_Reg
call Lock_Chip
ret
Disable_Watchdog Endp
;[]===============================================
; Name : Unlock_Chip
; IN : None
; OUT : None
;[]===============================================
Unlock_Chip Proc Near
mov dx, 2Eh
mov al, 87h
out dx, al
out dx, al
ret
Unlock_Chip Endp
;[]================================================
IB865 User’s Manual
29
INSTALLATIONS
; Name : Lock_Chip
; IN : None
; OUT : None
;[]================================================
Unlock_Chip Proc Near
mov dx, 2Eh
mov al, 0AAh
out dx, al
ret
Unlock_Chip Endp
;[]================================================
; Name : Write_Reg
; IN : CL - register index
;
AL - Value to write
; OUT : None
;[]================================================
Write_Reg Proc Near
pushax
mov dx, 2Eh
mov al,cl
out dx,al
pop ax
inc dx
out dx,al
ret
Write_Reg Endp
;[]================================================
; Name : Read_Reg
; IN : CL - register index
; OUT : AL - Value to read
;[]===================================================
Read_Reg
Proc Near
mov al, cl
mov dx, 2Eh
out dx, al
inc dx
in al, dx
ret
Read_Reg
Endp
;[]================================================
30
IB865 User’s Manual
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the Award
BIOS that comes with the CPU card. The topics covered in this chapter
are as follows:
BIOS Introduction................................................................... 32
BIOS Setup ............................................................................. 32
Standard CMOS Setup........................................................... 34
Advanced BIOS Features ....................................................... 37
Advanced Chipset Features .................................................... 40
Integrated Peripherals ............................................................. 43
Power Management Setup...................................................... 46
PNP/PCI Configurations ........................................................ 49
PC Health Status..................................................................... 50
Frequency/Voltage Control..................................................... 51
Load Fail-Safe Defaults.......................................................... 52
Load Setup Defaults ............................................................... 52
Set Supervisor/User Password............................................... 52
Save & Exit Setup .................................................................. 52
Exit Without Saving ............................................................... 52
IB865 User’s Manual
31
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your
computer system’s ROM supports Intel Pentium 4 processors. The BIOS
provides critical low-level support for a standard device such as disk
drives, serial ports and parallel ports. It also adds virus and password
protection as well as special support for detailed fine-tuning of the
chipset controlling the entire system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you
to enter the Setup utility. If you are a little bit late pressing the <Del>
key, POST (Power On Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message will
appear on the screen:
Press <DEL> to Enter Setup
In general, you press the arrow keys to highlight items, <Enter> to
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help
and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
32
IB865 User’s Manual
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Frequency/Voltage Control
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
ESC : Quit
á â à ß : Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type…
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the
control keys section, there is another section, which displays
information on the currently highlighted item in the list.
Note:
If the system cannot boot after making and saving system
changes with Setup, the Award BIOS supports an override to
the CMOS settings that resets your system to its default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum performance
and reliability. Changing the defaults could cause the system
to become unstable and crash in some cases.
IB865 User’s Manual
33
BIOS SETUP
Standard CMOS Setup
“Standard CMOS Setup” choice allows you to record some basic
hardware configurations in your computer system and set the system
clock and error handling. If the CPU card is already installed in a
working system, you will not need to select this option. You will need to
run the Standard CMOS option, however, if you change your system
hardware configurations, the onboard battery fails, or the configuration
stored in the CMOS memory was lost or damaged.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Thu, May 21, 2001
00 : 00 : 00
Item Help
Menu Level
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
IDE Channel 2 Master
IDE Channel 3 Master
Press Enter 13020 MB
Press Enter None
Press Enter None
Press Enter None
Change the day, month,
Year and century
Drive A
Drive B
1.44M, 3.5 in.
None
Video
EGA/VGA
Halt On
All , But Keyboard
Base Memory
Extended Memory
Total Memory
640K
129024K
130048K
At the bottom of the menu are the control keys for use on this menu. If
you need any help in each item field, you can press the <F1> key. It will
display the relevant information to help you. The memory display at the
lower right-hand side of the menu is read-only. It will adjust
automatically according to the memory changed. The following
describes each item of this menu.
Date
The date format is:
Day :
Sun to Sat
1 to 12
1 to 31
Month :
Date :
Year :
1994 to 2079
To set the date, highlight the “Date” field and use the PageUp/
PageDown or +/- keys to set the current time.
34
IB865 User’s Manual
BIOS SETUP
Time
The time format is: Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/
<PgDn> or +/- keys to set the current time.
IDE Primary HDDs / IDE Secondary HDDs
The onboard PCI IDE connectors provide Primary and Secondary
channels for connecting up to four IDE hard disks or other IDE devices.
Each channel can support up to two hard disks; the first is the “Master”
and the second is the “Slave”.
Press <Enter> to configure the hard disk. The selections include Auto,
Manual, and None. Select ‘Manual’ to define the drive information
manually. You will be asked to enter the following items.
CYLS :
HEAD :
Number of cylinders
Number of read/write heads
PRECOMP : Write precompensation
LANDZ :
Landing zone
SECTOR :
Number of sectors
The Access Mode selections are as follows:
Auto
Normal(HD < 528MB)
Large (for MS-DOS only)
LBA (HD > 528MB and supports
Logical Block Addressing)
Remarks: The main board supports two serial ATA ports and are
represented in this setting as IDE Channel 2 / 3 Master.
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
360KB 1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
IB865 User’s Manual
35
BIOS SETUP
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
Power up in 40 column mode.
Power up in 80 column mode.
For Hercules or MDA adapters.
CGA 40
CGA 80
MONO
Halt On
This field determines whether or not the system will halt if an error is
detected during power up.
No errors
The system boot will not be halted for any error
that may be detected.
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
The system boot will not be halted for a
keyboard error; it will stop for all other errors
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Keyboard
All, But Diskette
All, But Disk/Key
The system boot will not be halted for a key-
board or disk error; it will stop for all others.
36
IB865 User’s Manual
BIOS SETUP
Advanced BIOS Features
This section allows you to configure and improve your system and
allows you to set up some system features according to your preference.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
CPU Feature
Press Enter
Press Enter
Press Enter
Disabled
Enabled
Enabled
Enabled
Floppy
Hard Disk
CD-ROM
Enabled
Disabled
Disabled
On
ITEM HELP
Menu Level
Hard Disk Boot Priority
CD-ROM Boot Priority
Virus Warning
CPU L1 and L2 Cache
Hyper-threading Technology
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Allows you choose
the VIRUS warning
feature for IDE Hard
Disk boot sector
protection. If this
function is enabled
and someone
attempt to write data
into this area, BIOS
will show a warning
message on screen
and alarm beep
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up Numlock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (chars/Sec)
Typematic Delay (Msec)
Security Option
Fast
Disabled
6
250
Setup
APIC Mode
Enabled
1.4
Non-OS2
Yes
MPS Version Control for OS
OS Select For DRAM>64MB
Report No FDD For WIN 95
Small Logo (EPA) Show
Enable
CPU Feature
Press Enter to configure the settings relevant to CPU Feature.
Hard Disk / CD-ROM Boot Priority
This item allows you to set the priority for hard disk boot. When you press enter,
the selections shows the current hard disks used in your system as well as the
“Bootable Add-in Card” that is relevant to other boot sources media such as
SCSI cards and LAN cards.
Virus Warning
If this option isenabled, an alarm message will be displayed when trying to write
on the boot sector or on the partition table on the disk, which is typical of the
virus.
CPU L1 and L2 Cache
Cache memory is additional memory that is much faster than conventional
DRAM (system memory). CPUs from 486-type on up contain internal cache
memory, and most, but not all, modern PCs have additional (external) cache
memory. When the CPU requests data, the system transfers the requested data
from the main DRAM into cache memory, for even faster access by the CPU.
These items allow you to enable (speed up memory access) or disable the cache
function. By default, these items are Enabled.
IB865 User’s Manual
37
BIOS SETUP
Hyper-Threading Technology
This feature is enabled when your processor supports Hyper-Threading
Technology. Otherwise, this field will be hidden.
Quick Power On Self Test
When enabled, this field speeds up the Power On Self Test (POST) after the
system is turned on. If it is set to Enabled, BIOS will skip some items.
First/Second/Third Boot Device
These fields determine the drive that the system searches first for an
operating system. The options available include Floppy, LS/ZIP,
HDD-0, SCSI, CDROM, HDD-1, HDD-2, HDD-3, LAN and Disable.
Boot Other Device
These fields allow the system to search for an operating system from
other devices other than the ones selected in the First/Second/Third Boot
Device.
Swap Floppy Drive
This item allows you to determine whether or not to enable Swap Floppy
Drive. When enabled, the BIOS swaps floppy drive assignments so that
Drive A becomes Drive B, and Drive B becomes Drive A. By default,
this field is set to Disabled.
Boot Up Floppy Seek
This feature controls whether the BIOS checks for a floppy drive while
booting up. If it cannot detect one (either due to improper configuration
or its absence), it will flash an error message.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up the
system.
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a
device used to address memory above 1 MB.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
38
IB865 User’s Manual
BIOS SETUP
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. Settings are from 6 to 30 characters per second.
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
APIC Mode
APIC stands for Advanced Programmable Interrupt Controller. The
default setting is Enabled.
MPS Version Control for OS
This option is specifies the MPS (Multiprocessor Specification) version
for the OS. MPS version 1.4 added extended configuration tables to
improve support for multiple PCI bus configurations and improve future
expandability. The default setting is 1.4.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is Non-OS/2.
Report No FDD For WIN 95
If you are using Windows 95/98 without a floppy disk drive, select
Enabled to release IRQ6. This is required to pass Windows 95/98's SCT
test. You should also disable the Onboard FDC Controller in the
Integrated Peripherals screen when there's no floppy drive in the system.
If you set this feature to Disabled, the BIOS will not report the missing
floppy drive to Win95/98.
Small Logo (EPA) Show
The EPA logo appears at the right side of the monitor screen when the
system is boot up. The default setting is Enabled.
IB865 User’s Manual
39
BIOS SETUP
Advanced Chipset Features
This Setup menu controls the configuration of the chipset.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
CAS Latency Time
Active to Precharge Delay
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
Memory Frequency For
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole at 15M-16M
Delay Prior to Thermal
AGP Aperture Size (MB)
Init Display First
By SPD
2.5
6
3
3
ITEM HELP
Menu Level
Auto
Enabled
Disabled
Disabled
16 Min
128
Onboard/AGP
** On-Chip VGA Setting **
On-Chip VGA
On-Chip Frame Buffer Size
Boot Display
Enabled
8MB
CRT + LVDS
Auto
Panel Scaling
Panel Number
TV Standard
1024x768 LVDS
Off
Video Connector
TV Format
Automatic
Auto
DRAM Timing Selectable
This option refers to the method by which the DRAM timing is selected.
The default is By SPD.
CAS Latency Time
You can select CAS latency time in HCLKs of 2/2 or 3/3. The system
board designer should set the values in this field, depending on the
DRAM installed. Do not change the values in this field unless you
change specifications of the installed DRAM or the installed CPU. The
choices are 2 and 3.
Active to Precharge Delay
The default setting for the Active to Precharge Delay is 6.
DRAM RAS# to CAS# Delay
This option allows you to insert a delay between the RAS (Row Address
Strobe) and CAS (Column Address Strobe) signals. This delay occurs
when the SDRAM is written to, read from or refreshed. Reducing the
delay improves the performance of the SDRAM.
40
IB865 User’s Manual
BIOS SETUP
DRAM RAS# Precharge
This option sets the number of cycles required for the RAS to accumulate
its charge before the SDRAM refreshes. The default setting for the
Active to Precharge Delay is 3.
Memory Frequency For
This field sets the frequency of the DRAM memory installed. The
default setting is Auto. The other settings are PC200 and PC266.
System BIOS Cacheable
The setting of Enabled allows caching of the system BIOS ROM at
F000h-FFFFFh, resulting in better system performance. However, if
any program writes to this memory area, a system error may result.
Video BIOS Cacheable
The Setting Enabled allows caching of the video BIOS ROM at
C0000h-F7FFFh, resulting in better video performance. However, if
any program writes to this memory area, a system error may result.
Memory Hole At 15M-16M
In order to improve performance, certain space in memory can be
reserved for ISA cards. This memory must be mapped into the memory
space below 16 MB. The choices are Enabled and Disabled.
Delay Prior to Thermal
This field activates the CPU thermal function after the systems boots for
the set number of minutes. The options are 16Min and 64Min.
AGP Aperture Size
The field sets aperture size of the graphics. The aperture is a portion of
the PCI memory address range dedicated for graphics memory address
space. Host cycles that hit the aperture range are forwarded to the AGP
without any translation. The default setting is 128M.
Init Display First
This field allows the system to initialize first the VGA on chip or the
display card on the PCI Slot.
IB865 User’s Manual
41
BIOS SETUP
On-Chip VGA
By default, the On-Chip VGA or 865G chipset-integrated VGA is
Enabled.
On-Chip Frame Buffer Size
The On-Chip Frame Buffer Size canbe set us 1MB, 8MB or 16MB. This
memory is shared with the system memory.
Boot Display
Boot Display determines the display output device where the system
boots. The default setting is LVDS.
Panel Scaling
With the default setting of Auto, this item automatically displays the
resolution of the panel used in the system to ‘full’ screen.
Panel Number
By default, this item is set to 1024 x 768 LVDS. If you are using other
kinds of panel, enter this field to select the one that suits your panel.
TV Standard
By default, this item is set to off.
Video Connector
By default, this item is set to Automatic.
TV Format
By default, this item is set to Auto.
42
IB865 User’s Manual
BIOS SETUP
Integrated Peripherals
This section sets configurations for your hard disk and other integrated
peripherals. The first screen shows three main items for user to select.
Once an item selected, a submenu appears. Details follow.
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
Press Enter
Press Enter
Press Enter
ITEM HELP
Menu Level
On-Chip Primary IDE Device
Onboard Device
SuperIO Device
Onboard Lan Boot ROM
Enable
Phoenix - AwardBIOS CMOS Setup Utility
OnChip IDE Device
Enabled
ITEM HELP
Menu Level
IDE Block Mode
Enabled
Auto
Auto
Auto
Auto
Enabled
Auto
Auto
Auto
Auto
On-Chip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
*** On-Chip Serial ATA Setting ***
Auto
SATA0 master
On-Chip Serial ATA
Serial ATA Port0 Mode
Seril ATA Port1 Mode
SATA1 master
Phoenix - AwardBIOS CMOS Setup Utility
Onboard Device
Enabled
ITEM HELP
USB 2.0 Controller
USB Controller
USB Keyboard Support
USB Mouse Support
AC97 Audio
Enabled
Disabled
Disabled
Menu Level
Auto
CSA LAN (Giga-LAN)
Enable
IB865 User’s Manual
43
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
SuperIO Device
ITEM HELP
Menu Level
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
Onboard Parallel Port
Parallel Port Mode
Enabled
3F8/IRQ4
2F8/IRQ3
Normal
378/IRQ7
SPP
Power After PWR-Fail
off
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
OnChip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel
separately.
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster.
Rather than have the BIOS issue a series of commands that transfer to or
from the disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controllerand CPU directly. The system supports
five modes, numbered from 0 (default) to 4, which primarily differ in
timing. When Auto is selected, the BIOS will select the best mode.
IDE Primary/Secondary Master/Slave UDMA
These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature. The options are Auto and
Disabled.
On-Chip Serial ATA
The default setting of Auto allows the Serial ATA drive to be enabled,
when the system detects one.
USB Controller
By default, this field is set to Enabled.
USB 2.0 Controller
By default, this field is set to Disabled. In order to use USB 2.0,
necessary OS drivers must be installed first.
44
IB865 User’s Manual
BIOS SETUP
USB Keyboard Support
By default, this field is set to Disabled.
USB Mouse Support
By default, this field is set to Disabled.
AC97 Audio
The default setting of the AC97 Audio is Auto.
CSA LAN (Giga-LAN)
The default setting of the onboard Gigabit LAN is enabled.
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC)
installed on the CPU card and you wish to use it. If you install an add-in
FDC or the system has no floppy drive, select Disabled in this field. This
option allows you to select the onboard FDD port.
Onboard Serial/Parallel Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 1
Serial Port 2
Parallel Port
3F8/IRQ4
2F8/IRQ3
378H/IRQ7
UART Mode Select
This field determines the UART 2 mode in your computer. The default
value is Normal. Other options include IrDA and ASKIR.
Parallel Port Mode
This field allows you to determine parallel port mode function.
SPP
EPP
ECP
Standard Printer Port
Enhanced Parallel Port
Extended Capabilities Port
Power After PWR-Fail
This field refers to the power status (ON/Off) of the system when the
power returns to the system after power is cut off.
Onboard Lan Boot ROM
By default, the on board LAN boot ROM is enabled.
IB865 User’s Manual
45
BIOS SETUP
Power Management Setup
The Power Management Setup allows you to save energy of your system
effectively.
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
ATX
ITEM HELP
Menu Level
Menu Level
Power-Supply Type
ACPI Function
Enabled
User Define
V/H SYNC+Blank
Yes
Power Management
Video Off Method
Video Off In Suspend
Suspend Type
Stop Grant
3
Modem Use IRQ
Suspend Mode
Disabled
Disabled
Instant-Off
50%
Disabled
Disabled
Disabled
Disabled
0
HDD Power Down
Soft-Off by PWR-BTTN
CPU THRM-Throttling
Wake-Up by PCI Card
Power On by Ring
Wake Up on CSA Lan
Resume by Alarm
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
0 : 0 : 0
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
FDD, COM, LPT Port
PCI PIRQ[A-D] #
Power Supply Type
This field sets the power supply type that is in your system. By default,
the setting is set to ATX.
ACPI Function
Enable this function to support ACPI (Advance Configuration and
Power Interface).
46
IB865 User’s Manual
BIOS SETUP
Power Management
This field allows you to select the type of power saving management
modes. There are four selections for Power Management.
Min. Power Saving
Max. Power Saving
User Define
Minimum power management
Maximum power management.
Each of the ranges is from 1 min. to
1hr. Except for HDD Power Down
which ranges from 1 min. to 15 min.
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank
Default setting, blank the screen and turn
off vertical and horizontal scanning.
Allows BIOS to control the video display.
Writes blanks to the video buffer.
DPMS
Blank Screen
Video Off In Suspend
When enabled, the video is off in suspend mode. The default setting is
Yes.
Suspend Type
The default setting for the Suspend Type field is Stop Grant.
Modem Use IRQ
This field sets the IRQ used by the Modem. By default, the setting is 3.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Soft-Off by PWRBTN
This field defines the power-off mode when using an ATX power
supply. The Instant Off mode allows powering off immediately upon
pressing the power button. In the Delay 4 Sec mode, the system powers
off when the power button is pressed for more than four seconds or
enters the suspend mode when pressed for less than 4 seconds.
IB865 User’s Manual
47
BIOS SETUP
CPU THRM-Throttling
When the system enters Doze mode, the CPU clock runs only part of the
time. You may select the percent of time that the clock runs.
Wake-Up by PCI Cards
Enable this field to allow wake up function through a PCI card.
Power On by Ring
This field enables or disables the power on of the system through the
modem connected to the serial port or LAN.
Wake Up On CSA Lan
Enable this field to allow wake up function through the onboard CSA
LAN.
Resume by Alarm
This field enables or disables the resumption of the system operation.
When enabled, the user is allowed to set the Date and Time.
Reload Global Timer Events
The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events which
can prevent the system from entering a power saving mode or can
awaken the system from such a mode. When an I/O device wants to gain
the attention of the operating system, it signals this by causing an IRQ to
occur. When the operating system is ready to respond to the request, it
interrupts itself and performs the service.
48
IB865 User’s Manual
BIOS SETUP
PNP/PCI Configurations
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
No
ITEM HELP
Menu Level
PNP OS Install
Disabled
Reset Configuration Data
Default is Disabled.
Auto (ESCD)
Press Enter
Press Enter
Resources Controlled By
IRQ Resources
Select Enabled to reset
Extended System
Configuration Data
(ESCD) when you exit
Setup if you have
installed a new add-on
and the system
reconfiguration has
caused such a serious
conflict that the OS
cannot boot
DMA Resources
Disabled
PCI/VGA Palette Snoop
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
INT Pin 1 Assignment
INT Pin 2 Assignment
INT Pin 3 Assignment
INT Pin 4 Assignment
INT Pin 5 Assignment
INT Pin 6 Assignment
INT Pin 7 Assignment
INT Pin 8 Assignment
PNP OS Install
Enable the PNP OS Install option if it is supported by the operating
system installed. The default value is No.
Reset Configuration Data
This field allows you to determine whether to reset the configuration
data or not. The default value is Disabled.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices
automatically with the use of a use a PnP operating system such as
Windows 95.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
This field allows you to set whether or not MPEG ISA/VESA VGA
cards can work with PCI/VGA. When this field is enabled, a PCI/VGA
can work with an MPEG ISA/VESA VGA card. When this field is
disabled, a PCI/VGA cannot work with an MPEG ISA/VESA card.
IB865 User’s Manual
49
BIOS SETUP
PC Health Status
This section shows the parameters in determining the PC Health Status.
These parameters include temperatures, fan speeds and voltages.
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
ITEM HELP
CPU Warning Temperature
Current SystemTemp.
Current CPU Temp.
Disabled
34°C/93°F
35°C/95°F
34°C/93°F
4166 RPM
5625PM
Current System Temp.
CPU FAN Speed
Chassis FAN1 Speed
Chassis FAN2 Speed
0 RPM
1.63V
3.37V
Vcore (V)
Vcc3(V)
5.05V
+5(V)
12.09V
(-)12.03V
3.21V
+12(V)
-12(V)
VBAT
5.05V
5VSB(V)
Shutdown Temperature
Temperature Warning Beep
CPU Fan Failure Warning
Sys FAN Failure Warning
Aux FAN Failure Warning
Disabled
Disabled
Disabled
Disabled
Disabled
CPU Warning Temperature
This field allows the user to set the temperature so that when the
temperature is reached, the system sounds a warning. This function can
help prevent damage to the system that is caused by overheating.
Temperatures/Fan Speeds/Voltages
These fields are the parameters of the hardware monitoring function
feature of the CPU card. The values are read-only values as monitored by
the system and show the PC health status.
Shutdown Temperature
This field allows the user to set the temperature by which the system
automatically shuts down once the threshold temperature is reached.
This function can help prevent damage to the system that is caused by
overheating.
Temperature/CPU/Chassis Fan Failure Warning
When enabled, this field lets the system sounds an audible warning to
the user that the CPU fan or chassis fan has malfunctioned.
50
IB865 User’s Manual
BIOS SETUP
Frequency/Voltage Control
This section shows the user how to configure the processor frequency.
Phoenix - AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
Disabled
Disabled
ITEM HELP
Menu Level
Auto Detect PCI Clk
Spread Spectrum
Auto Detect PCI Clk
This field enables or disables the auto detection of the PCI clock.
Spread Spectrum
This field sets the value of the spread spectrum. The default setting is
Disabled. This field is for CE testing use only.
IB865 User’s Manual
51
BIOS SETUP
Load Fail-Safe Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
Load Setup Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
Set Supervisor/User Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password,
the screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are
prompted to enter the password. A message will confirm the password to
be disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
Save & Exit Setup
This option allows you to determine whether or not to accept the
modifications. If you type “Y”, you will quit the setup utility and save all
changes into the CMOS memory. If you type “N”, you will return to
Setup utility.
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
52
IB865 User’s Manual
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers under the Windows 98, Windows NT 4.0 and Windows 2000.
The software and drivers are included with the CPU card. If you find the
items missing, please contact the vendor where you made the purchase.
The contents of this section include the following:
Intel 865G Chipset Software Intallation Utility................ 54
Intel 865G Chipset Graphics Driver ................................ 57
Realtek AC97 Codec Audio Driver Installation ............... 59
Intel PRO LAN Drivers Installation ................................ 60
IMPORTANT NOTE:
After installing your Windows operating system (Windows
98/98SE/ME/2000/XP), you must install first the Intel Chipset Software
Installation Utility before proceeding with the drivers installation.
IB865 User’s Manual
53
DRIVERS INSTALLATION
Intel 865G Chipset Software Intallation Utility
The Intel 865G Chipset Drivers should be installed first before the
software drivers to enable Plug & Play INF support for Intel chipset
components. Follow the instructions below to complete the installation
under Windows 98/98SE/ME/2000/XP.
1. Insert the CD that comes with the CPU card and the screen below
would appear. Click Intel Chipsets and then Intel 865G Chipset Family
Drivers.
2. Click Intel 865G Chipset Software Intallation Utility.
54
IB865 User’s Manual
DRIVERS INSTALLATION
3. When the Welcome screen appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with
the installation process.
IB865 User’s Manual
55
DRIVERS INSTALLATION
5. On Readme Information screen, click Next to continue the
installation.
6. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect. When the computer has
restarted, the system will be able to find some devices. Restart your
computer when prompted.
56
IB865 User’s Manual
DRIVERS INSTALLATION
Intel 865G Chipset Graphics Driver
The Intel 865G Chipset Family Graphics Drivers come in the CD with
the CPU card . Follow the instructions below to complete the
installation under Windows 98/98SE/ME/2000/XP.
1. Insert the CD that comes with the CPU card and the screen below
would appear. Click Intel Chipsets and then Intel 865G Chipset Family
Drivers.
2. When the Welcome screen appears, click Next to continue.
IB865 User’s Manual
57
DRIVERS INSTALLATION
3. Click Yes to accept the software license agreement and proceed with
the installation process.
4. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect. When the computer has
restarted, the system will be able to find some devices. Restart your
computer when prompted.
58
IB865 User’s Manual
DRIVERS INSTALLATION
Realtek AC97 Codec Audio Driver Installation
Follow the steps below to installthe Realtek AC97 Codec Audio Drivers.
1. Insert the CD that comes with the CPU card and the screen below
would appear. Click Intel Chipsets, then Intel 865G Chipset Family
Drivers. Click Realtek AC97 Codec Audio Drivers to start installation.
2. Click Finish to restart the computer and for changes to take effect. .
IB865 User’s Manual
59
DRIVERS INSTALLATION
Intel PRO LAN Drivers Installation
The Intel PRO LAN drivers support both Intel® PRO/100 and
PRO/1000 drivers. Follow the steps below to complete the installation.
1. Insert the CD that comes with the CPU card and the screen below
would appear. Click on LAN Card on the left side to make the LAN
drivers selection. Click on Intel(R) PRO LAN Drivers.
2. Click Install Now.
3. Click Restart to restart the computer and new settings to take effect.
60
IB865 User’s Manual
|