Instruction Manual
Recommendations to avoid or minimize phosphor burn-in:
NOTE:
When you connect a computer to this monitor, attach
the supplied ferrite cores. If you do not do this, this
monitor will not conform to mandatory FCC standards.
Attaching the ferrite cores:
Set the ferrite cores on both ends of the DVI cable (not
supplied), and one end of the power cable (supplied).
Close the lid tightly until the clamps click.
Use the band to secure the ferrite core (supplied).
Like all phosphor-based display devices and all other gas
plasma displays, plasma monitors can be susceptible to
phosphor burn under certain circumstances. Certain
operating conditions, such as the continuous display of a
static image over a prolonged period of time, can result in
phosphor burn if proper precautions are not taken. To protect
your investment in this Integra plasma monitor, please adhere
to the following guidelines and recommendations for
minimizing the occurrence of image burn:
DVI cable (not supplied)
Connector
band
band
* Always enable and use your computer’s screen saver
function during use with a computer input source.
* Display a moving image whenever possible.
* Change the position of the menu display from time to time.
* Always power down the monitor when you are finished
using it.
core (small)
core (small)
Power cable (supplied)
core (large)
If the plasma monitor is in long term use or continuous
operation take the following measures to reduce the
likelihood of phosphor burn:
band
(Plasma Monitor side)
Set side
* Lower the Brightness and Contrast levels as much as
possible without impairing image readability.
* Display an image with many colors and color gradations
(i.e. photographic or photo-realistic images).
* Create image content with minimal contrast between light
and dark areas, for example white characters on black
backgrounds. Use complementary or pastel color whenever
possible.
To avoid damage and prolong operating life:
1. Use only with 120V 50/60Hz AC power supply.
Continued operation at line voltages greater than 120Volts
AC will shorten the life of the unit, and might even cause
a fire hazard.
2. Handle the unit carefully when installing it and do not
drop.
3. Set the unit away from heat, excessive dust, and direct
sunlight.
* Avoid displaying images with few colors and distinct,
sharply defined borders between colors.
4. Protect the inside of the unit from liquids and small
metal objects. In case of accident, unplug the unit and
have it serviced by an authorized Integra/Onkyo service
station.
5. Do not hit or scratch the panel surface as this causes
flaws on the surface of the screen.
6. For correct installation and mounting it is strongly
recommended to use a trained, authorized Integra dealer.
7. As is the case with any phosphor-based display (like a
CRT monitor, for example) light output will gradually
decrease over the life of a Plasma Display Panel.
Précautions
Mises en garde et précautions de
Veuillez lire ce manuel avec attention avant d’utiliser votre
moniteur Plasma Monitor Integra et conserver ce manuel à
portée de la main pour une consultation ultérieure.
sécurité
Le moniteur Plasma Monitor Integra a été conçu et
fabriqué pour une utilisation fiable et durable. Il ne
nécessite aucun entretien en dehors du nettoyage.
Utiliser un chiffon doux et sec pour nettoyer la surface
de l’écran. Ne jamais utiliser de solvant comme
l’alcool ou le diluant. Le panneau à affichage plasma
est constitué de fines particules d’images ou pixels
(cellules). Bien que Integra produise des panneaux
à affichage plasma avec plus de 99,99 % de cellules
actives, il peut y avoir des cellules qui ne produisent
pas de lumière
ATTENTION
RISQUE D’ELECTROCUTION
NE PAS OUVRIR
MISE EN GARDE
:
AFIN DE REDUIRE LES RISQUES D’ELECTRO-
CUTION, NE PAS DEPOSER LE COUVERCLE, IL N’Y
A AUCUNE PIECE UTILISABLE A L’INTERIEUR DE
CET APPAREIL. NE CONFIER LES TRAVAUX
D’ENTRETIEN QU’A UN PERSONNEL QUALIFIE.
ou qui restent allumées.
Pour des raisons de sécurité et pour éviter
d’endommager l’appareil, lire attentivement les
instructions suivantes.
Ce symbole a pour but de prévenir l’utilisateur de la
présence d’une tension dangereuse, non isolée se trouvant
à l’intérieur de l’appareil. Elle est d’une intensité suffisante
pour constituer un risque d’électrocution. Eviter le contact
avec les pièces à l’intérieur de cet appareil.
Pour éviter les risques d’éléctrocution et d’incendie:
1. Laisser suffisament d’espace autour de l’appareil pour
la ventilation et éviter toute augmentation excessive de
la température interne. Ne pas couvrir les évents ou
l’installer dans un endroit trop exigu.
L’appareil est équipé de ventilateurs de refroidissement.
Si vous installez l’appareil dans un espace clos,
assurezvous qu’il y ait suffisamment d’espace au dessus
pour permettre à l’air chaud de s’élever et de s’évacuer.
Si la température du moniteur devient excessive, la
protection contre les surchauffes entrera en action et
coupera l’alimentation. Dans ce cas, éteindre l’appareil
et débrancher le câble d’alimentation. Si la température
de la pièce dans laquelle le moniteur est installé est
particulièrement excessive, déplacer l’appareil dans un
endroit plus frais et le laisser refroidir 60 minutes. Si le
problème persiste, prendre contact avec le revendeur
Integra pour le service après-vente.
Ce symbole a pour but de prévenir l’utilisateur de la
présence d’importantes instructions concernant l’entretien
et le fonctionnement de cet appareil. Par conséquent, elles
doivent être lues attentivement afin d’éviter des problèmes.
AVERTISSEMENT
AFIN DE REDUIRE LES RISQUES D’INCENDIE OU
D’ELECTROCUTION, NE PAS EXPOSER CETAPPAREIL
ALAPLUIE OUAL’HUMIDITE.AUSSI, NE PAS UTILISER
LA FICHE POLARISEE AVEC UN PROLONGATEUR OU
UNEAUTRE PRISE DE COURANT SAUF SI CES LAMES
PEUVENT ETRE INSEREES A FOND. NE PAS OUVRIR
LE COFFRET, DES COMPOSANTS HAUTETENSION SE
2. Ne pas utiliser la fiche polarisée du cordon d’alimentation
avec des prolongateurs ou des prises de courant, sauf si
les lames peuvent être insérées à fond.
TROUVENT
A
L’INTERIEUR. LAISSER
A
UN
PERSONNEL QUALIFIE LE SOIN DE REPARER CET
APPAREIL.
3. Ne pas exposer à L’eau ou à l’humidité.
4. Eviter d’endommager le cordon d’alimentation, et ne pas
modifier le cordon d’alimentation.
DOC avis de conformation
Cet appareil numérigue de la classeArespecte toutes les exigences
du Réglement sur le Matériel Brouilleur du Canada.
5. Débrancher l’appareil pendant les tempêtes ou si
l’appareil n’est pas utilisé pendant une longue période.
6. Ne pas ouvrir le coffret. Des composants de haute
tension se trouvent à l’intérieur. Si l’appareil est
endommagé de cette manière, la garantie devient
caduque. De plus, il y a risque d’électrocution.
7. Ne pas essayer de réparer ou entretenir l’appareil
soimême. Integra ne saura être tenu pour responsable
pour toute blessure ou dommage causé par des
personnes non qualifiées qui essayent de réparer ou
d’ouvrir le couvercle arrière. Confier toute réparation
à un centre de service agréé Integra/Onkyo.
Pour éviter le risque de combustion au phosphore, les
mesures suivantes sont recommandées :
REMARQUE:
Lorsque vous branchez un micro-ordinateur sur ce
moniteur, fixez les noyaux en ferrites fournis. Si vous
ne le faîtes, le moniteur ne sera pas en conformité avec
les exigences des standards FCC.
Comme tous les appareils d’affichage à base de phosphore
et tous les autres affichages à gaz plasma, les moniteurs
Plasmasync peuvent être sujets à la combustion au
phosphore dans certaines circonsatnces. Certaines
conditions d’utilisation, telles que l’affichage continu d’une
image statique pour une durée prolongée, peuvent causer des
brûlures au phophore si aucune précaution n’est prise. Pour
protéger votre investissement dans ce moniteur PlasmaSync
Integra, veuillez suivre les directives et les recommandations
suivantes pour minimiser l’occurence de brûlure d’image :
Fixation des noyaux en ferrite.
Installez les noyaux en ferrite sur chaque bout du câble
DVI (non fourni), ainsi que sur un côté du câble
d’alimentation électrique (founi).
Fermez doucement le couvercle jusqu’à ce que les crans
se clipsent.
Utiliser les colliers pour fixer la tore en ferrite (fourni)
Câble DVI (non fourni)
Connecteur
• Assurez-vous de mettre en marche et d’utliser
l’économisateur d’écran chaque fois que c’est possible
lorsque vous l’utilisez avec une source d’entrée
d’ordinateur.
• Affichez une image en mouvement aussi souvent que
possible.
Collier
Collier
noyau (petit)
noyau (petit)
• Changer la position de l’affichage de menu de temps àautre.
• Coupez toujours l’alimentation lorsque vous avez terminé
d’utiliser la moniteur.
Câble d'alimentation
électrique (fourni)
noyau (large)
Collier
Si le moniteur est en usage continu ou longue durée, prenez
les mesures suivantes afin d’éviter l’occurence de
combustion au phosphore :
Côté de l'appareil
(côté du moniteur à plasma)
• Abaissez le niveau de l’image (contraste, luminosité)
autant que possible, sans faire perdre la lisibilité de
l’image.
• Affichez une image avec de nombreuses couleurs et
graduations de couleur (par ex. des images
photographiques ou photo-réalistes).
• Créez un contenu d’image avec un contraste minimal
entre les zones sombres et les zones claires, par exemple,
des caractères blancs sur un fond noir. Utilisez des
couleurs complémentaires ou pastels le plus souvent
possible.
Pour éviter des dommages et prolonger la durée de
service de l’appareil:
1. N’utiliser qu’une source d’alimentation de 120 V 50/
60 Hz CA. Le fait d’utiliser l’appareil en continu à des
tensions de ligne supérieures à 120 Volts CA réduit sa
durée de vie et risque de provoquer un incendie.
2. Manipuler l’appareil avec soin pendant son
déplacement et ne pas le faire tomber.
3. Eloigner l’appareil des endroits chauds, très poussiéreux
et exposés en plein soleil.
4. Eviter que des liquides et des petits objets métalliques
pénètrent à l’intérieur de l’appareil. En cas d’accident,
débrancher l’appareil et le confier à un centre de service
agréé Integra/Onkyo.
• Évitez d’afficher des images avec peu de couleurs et des
limites nettes et clairement définies entre les couleurs.
5. Ne pas frapper ou rayer la surface de la écran plasma,
car des défauts risquent de se produire sur la surface
de la écran plasma.
6. Pour effectuer une installation et un montage corrects,
il est recommandé de faire appel au concessionnaire
Integra autorisé et spécialisé.
7. Comme c’est le cas pour tout affichage à base de
phosphore (comme un moniteur CRT, par exemple), la
puissance de lumière baisse graduellement au cours de
la vie du Panneau d’Affichage à Plasma.
Contents
How to Mount to the Plasma Monitor ................ 1
OSM Controls ................................................. 17
Menu Operations ................................................... 17
Picture Settings Menu............................................. 19
Adjusting the picture ................................................. 19
Setting the picture mode according to the
Introduction ..................................................... 2
Introduction to the Plasma Monitor PLA-50V1 .............. 2
The features you’ll enjoy include:............................... 2
Contents of the Package ........................................... 2
brightness of the room ............................................... 20
Setting the color temperature .................................... 21
Adjusting the color to the desired quality ................... 22
Reducting noise in the picture .................................... 23
Sound Settings Menu .............................................. 24
Adjusting the treble, bass and left/right balance ........ 24
Screen Settings Menu ............................................. 25
Adjusting the Position, Size, Fine Picture,
Picture Adj ................................................................ 25
Function Settings Menu .......................................... 26
Setting the on-screen display ..................................... 26
Adjusting the position of the menu display ................ 27
Setting the power management for computer images . 28
POWER/STANDBY indicator ................................... 29
Setting the gray level for the sides of the screen ......... 30
Setting the picture to suit the movie ........................... 30
Setting RGB3 ADJ. .................................................... 31
Reducing burn-in of the screen................................... 31
Resetting to the default values .................................... 32
Option Settings Menu ............................................. 33
Setting the allocation of the audio connectors ........... 33
Setting the BNC connectors ...................................... 33
Setting a computer image to the correct RGB
Part Names and Function ................................. 3
Front View............................................................... 3
Rear View / Terminal Board ...................................... 4
Remote Control Unit ................................................. 5
Battery Installation and Replacement .......................... 6
Using the wired remote control mode ......................... 7
Operating Range ..................................................... 7
Handling the remote control unit ................................ 7
Installation ...................................................... 8
Connecting Your PC or Macintosh Computer ............... 9
Connections with Equipment that has a Digital Interface ...
9
Connecting Your Document Camera ........................... 9
Connecting Your VCR or Laser Disc Player.................. 9
Connecting Your DVD Player ..................................... 9
External Speaker Connections.................................. 10
Pin Assignments and Signal Levels
for 15 pin RGB (Analog) ......................................... 11
Pin Configuration and Signal
of the RGB 3 IN Connector (DVI Connector) .............. 11
select screen ............................................................. 34
Setting high definition images to the suitable
Basic Operations............................................. 12
POWER ................................................................ 12
To turn the unit ON and OFF: .................................... 12
VOLUME .............................................................. 12
To adjust the volume: ................................................ 12
MUTE ................................................................... 12
To cancel the sound:.................................................. 12
DISPLAY ................................................................ 12
To check the settings: ................................................. 12
DIGITAL ZOOM ..................................................... 12
AUTO ADJUST ...................................................... 12
To adjust the size or quality of the picture
screen size ............................................................... 35
Setting the picture size for RGB input signals ............ 36
Information Menu ................................................. 36
Checking the frequencies, polarities of input signals,
and resolution ........................................................... 36
Setting the language for the menus............................. 37
Setting the video signal format .................................. 37
External Control ............................................. 39
Table of Signals Supported .............................. 47
automatically: ............................................................ 12
OFF TIMER ........................................................... 13
To set the off timer: ................................................... 13
To check the remaining time: ..................................... 13
To cancel the off timer ............................................... 13
Supported resolution .............................................. 47
Troubleshooting............................................. 49
Specifications ................................................. 50
WIDE Operations............................................. 14
Watching with a wide screen (manual) .................... 14
When watching videos or digital video discs............. 14
When watching high definition video source ............. 14
Watching computer images with a wide screen ......... 15
When “PICTURE SIZE” is set to “OFF” ................... 15
MULTI SCREEN Operations ............................... 16
Showing a couple of pictures on the screen
at the same time ................................................... 16
Selecting the input signals to be displayed ................. 16
Adjusting the OSM controls...................................... 16
How to Mount the Plasma Monitor
• This device cannot be installed on its own.
Be sure to use a stand or mounting unit
designed for Plasma Monitor PLA-50V1. (Wall
mount unit, Stand, etc.)
• For correct installation and mounting it is
strongly recommended to use a trained,
authorized Integra dealer.
Failure to follow correct mounting
procedures could result in damage to the
equipment or injury to the installer.
Product warranty does not cover damage
caused by improper installation.
Ventilation Requirements for
enclosure mounting
To allow heat to disperse, leave space between
surrounding objects as shown on the diagram
below when installing.
Wall
50mm (2")
50mm (2")
1240mm (48.8")
Wall
50mm (2")
1
Introduction
Introduction to the Plasma Monitor
Contents of the Package
Ⅺ Plasma Monitor PLA-50V1
Ⅺ Power cord
PLA-50V1
Integra’s Plasma Monitor is a seamless blend of cutting-
edge visual technology and sophisticated design. At 50-
inches, with a 16:9 aspect ratio, the Plasma Monitor PLA-
50V1 certainly makes a big impression. However, at a mere
4.2 inches/107 mm thin, the monitor’s sleek techno-art
lines blend in well with your environment. Plasma
Monitor’s crisp, vivid image quality will transform data
from any graphic medium from PCs to DVD players- into
art. And weighing only 101.3 lbs/ 46 kg, it actually can be
hung almost anywhere. Integra has made sure that a host
of multimedia resources can be easily connected and
displayed as brilliantly as intended on the Plasma monitor.
Ⅺ RGB cable (Mini D-Sub 15-pin to Mini D-Sub 15-
pin connector)
Ⅺ Adapter for Macintosh
Ⅺ Remote control unit with two AAA Batteries
Ⅺ Instruction manual
Ⅺ Registration card
Ⅺ 7 Days Customer service sheet
ⅪRemote cable
The features you’ll enjoy include:
• 50-inch screen
• 16:9 aspect ratio
Ⅺ Ferrite core (small×2, large×1), band
Ⅺ Safety metal fittings*
• Capsulated color filter and black matrix
• 4.2 inch / 107 mm thin
• 101.3 lbs/ 46 kg light
• High-resolution screen: 1365
ן 768 pixels • 160-degrees of off-axis viewing, horizontally and
vertically.
Ⅺ Screws for safety metal fiting*
* These are fittings for fastening the unit to a wall to prevent
tipping due to external shock when using the stand (option).
Fasten the safety fittings to the holes in the back of the
monitor using the safety fitting mount screws.
• Flicker - and warp - free display provides excellent
image geometry even in screen corners
• Not affected by magnetic fields, no color drift or edge
distortion.
• VGA, SVGA, XGA, SXGA, computer signal
compatibility
• NTSC, PAL, SECAM, composite and S-Video signal
compatibility
• 480P, 1080I, 720P and HDTV signal compatibility
• PCs, VCRs, Laser Disc and DVD player source
compatibility
• Scan conversion system automatically converts VGA,
SVGA and SXGA signals to the panel’s native resolution
• RGB input (3*), Video input (3), DVD/HD input (2*),
Audio input (3), External Control input (1)
• AccuColor control system provides user selectable on-
screen color temperature settings
• New Drive Technology
• Component video input terminal for DVD, 15.75kHz
(Y, CB, CR )
• Digital broadcasting source compatibitly
• Menu-driven on screen control system that makes image
adjustments a snap
• Seven languages (English, German, French, Italian,
Spanish, Swedish, and Japanese)
* You can select RGB source or Component source for
the 5BNC terminal. When selecting an RGB input, the
source is switched to the RGB input (3); when selecting
a component input, the source is switched to the DVD/
HD input (2).
2
Part Names and Function
Front View
POWER/STANDBY
INPUT SELECT
VOLUME
POWER/STANDBY
VOLUME
DOWN UP
INPUT SELECT
/EXIT
PROCEED
LEFT/–
RIGHT/+
q
w
e
r
t
y u
qPROCEED
t POWER/STANDBY indicator
Sets the On-Screen Menu (OSM) mode and displays
the main menu.
When the power is on ............................. Lights green.
When the power is in the standby mode ... Lights red.
w VOLUME DOWN and UP
y Power
Adjusts the volume. Functions as the CURSOR (L/
M) buttons in the On-Screen Menu (OSM) mode.
Turns the monitor’s power on and off.
u Remote sensor window
e LEFT/– and RIGHT/+
Receives the signals from the remote control unit.
Enlarges or reduces the image. Functions as the
ᮤ
ᮣ
CURSOR (
(OSM) mode.
/
) buttons in the On-Screen Menu
r INPUT SELECT / EXIT
Switches the input, in the following order:
→ VIDEO1 → VIDEO2 → VIDEO3→ DVD/HD
RGB/PC3 ← RGB/PC2 ← RGB/PC1←
Functions as the EXIT buttons in the On-Screen Menu
(OSM) mode.
3
Rear View/ Terminal Board
VIDEO
VIDEO
1
2
B
C
VIDEO
3
VIDEO
VIDEO
1
2
L(MONO)
VIDEO
3
R
Y
L(MONO)
R
Y
CB/PB
CR/PR
L(MONO)
R
CB/PB
CR/PR
L(MONO)
R
RGB
1
R/CR/PR
G/Y
B/CB/PB
HD
VD
L(MONO)
R
RGB
3
RGB
1
(Digital RGB)
SPEAKERS MUST
HAVE MORE THAN
7WATT RATING
OHM
D
E
CONTROL
LOCK
ON /OFF
IMPEDANCE
6
RIGHT LEFT
REMOTE
CONTROL
R/CR/PR
G/Y
EXTERNAL
CONTROL
AC IN
B/CB/PB
HD
VD
K
SPEAKERS MUST
HAVE MORE THAN
7WATT RATING
L(MONO)
R
J
IMPEDANCE
6
OHM
RIGHT LEFT
F
RGB
3
(Digital RGB)
CONTROL
LOCK
ON /OFF
G
H
REMOTE
CONTROL
A
EXTERNAL
CONTROL
I
A EXT SPEAKER L and R
G CONTROL LOCK
Connect speakers here.
When “CONTROL LOCK” is set “ON”, the buttons
on the set’s control panel do not function.
B VIDEO1, 2, 3
Connect VCR’s, DVD’s or Laser Discs, etc. here.
H REMOTE CONTROL
Connect the supplied remote cable here.
C DVD1 / HD1
Connect DVD’s, High Definition or Laser Discs, etc.
I
EXTERNAL CONTROL
here.
This terminal is used when power ON/OFF, input
selection and AUDIO MUTE and other controls are
operated externally (by external control). See also page
39 for external control.
D RGB1
Inputs the analog RGB signal of personal computer,
etc.
J AUDIO1, AUDIO2, AUDIO3
These are audio input terminals.
E RGB2/ DVD2/ HD2
RGB2:
Inputs the analog RGB signal.
The input is selectable. Set which video image to allot
them to on the menu screen.
DVD2/ HD2: Connect DVD’s, High Definition or
Laser Discs, etc. here.
K AC IN
F RGB3 (DVI 29pin)
Connect the included power cord here.
Inputs a digital RGB signal (TMDS).
4
Remote Control Unit
w RGB/PC
Press this button to select RGB/PC as the source.
→ RGB/PC1 → RGB/PC2 → RGB/PC3
RGB/PC can also be selected using the INPUT
SELECT button on the monitor. The input switches as
follows each time the button is pressed:
→ VIDEO1 → VIDEO2→ VIDEO3→ DVD/HD
RGB/PC3 ← RGB/PC2 ← RGB/PC1 ←
e DVD / HD
Press this button to select DVD/HD as the source.
DVD/HD can also be selected using the INPUT
SELECT button on the monitor. The input switches as
follows each time the button is pressed:
→ VIDEO1 → VIDEO2→ VIDEO3→ DVD/HD
RGB/PC3 ← RGB/PC2 ← RGB/PC1 ←
r VIDEO
Press this button to select VIDEO as the source.
→ VIDEO1 → VIDEO2 → VIDEO3
VIDEO can also be selected using the INPUT SELECT
button on the monitor. The input switches as follows
each time the button is pressed:
→ VIDEO1 → VIDEO2→ VIDEO3→ DVD/HD
RGB/PC3 ← RGB/PC2 ← RGB/PC1 ←
t PROCEED
Press this button to access the OSM controls.
Press this button during the display of the main menu
to go to the sub menu.
ᮤ
ᮣ
)
y CURSOR (L / M /
/
Use these buttons to select items or settings and to
adjust settings or switch the display patterns.
u EXIT
Press this button to exit the OSM controls in the main
menu. Press this button during the display of the sub
menu to return to the main menu.
i POINTER
Press this button to display the pointer.
o ZOOM (+ /–)
Enlarges or reduces the image.
! VOLUME (+ /–)
Adjusts the volume.
q POWER ON/OFF
Switches Power ON/OFF.
(This does not operate when POWER/STANDBY
indicator of the main unit is off.)
! MUTE
Mutes the sound.
! WIDE
The type of broadcast is detected automatically, and
the recommended wide screen is set.
5
! DISPLAY
Battery Installation and Replacement
Insert the 2 “AAA” batteries, making sure to set them in
with the proper polarity.
Displays the source settings on the screen.
! OFF TIMER
Activates the off timer for the unit.
1.Press and open the cover.
! MULTI
Press this button to select a screen mode from among
single mode, side by side, and picture in picture.
! SELECT
Press this button to select the active picture in a multi
screen mode.
! AUTO ADJUST
Press this button to adjust Fine Picture, Picture ADJ,
Position, and Contrast automatically, or to switch the
screen size to ZOOM mode automatically with the
superimposed caption displayed fully only when the
picture contains dark areas above and below the picture.
2.Align the batteries according to the (+) and (–) indication
inside the case.
! Remote control signal transmitter
Transmits the remote control signals.
! Remote Jack
Insert the plug of the supplied remote cable here when
using the supplied remote control unit in the wired
condition.
3.Replace the cover.
6
Using the wired remote control mode
Connect the supplied remote cable to the remote control
unit’s remote jack and the “REMOTE CONTROL”
terminal on the monitor.
Operating Range
* Use the remote control unit within a distance of about 7 m/
23ft. from the front of the monitor’s remote control sensor
and at a horizontal angle of within 30°.
When the cable is connected, the mode automatically
switches to wired remote control. When the wired remote
control mode is used, the remote control unit can be
operated even if no batteries are loaded.
* The remote control operation may not function if the
monitor’s remote control sensor is exposed to direct
sunlight or strong artificial light, or if there is an obstacle
between the sensor and the remote control unit.
VIDEO
VIDEO
1
2
CONTROL
LOCK
ON /OFF
VID
REMOTE
CONTROL
EXTERNAL
CONTROL
L(
R
POWER/STANDBY
LUME
INPUT SELECT
/EXIT
UP
LEFT/–
RIGHT/+
RGB
3
(Digital RGB)
RS MUST
ORE THAN
RATING
CONTROL
LOCK
ON /OFF
NCE
6
OHM
LEFT
REMOTE
CONTROL
EXTERNAL
CONTROL
Approx.
7m/ 23ft
30˚
30˚
Remote Control
Cable
To Remote Jack
Handling the remote control unit
• Do not drop or mishandle the remote control unit.
• Do not get the remote control unit wet. If the remote
control unit gets wet, wipe it dry immediately.
• Avoid heat and humidity.
• When not using the remote control unit for a long period,
remove the batteries.
• Do not use new and old batteries together, or use different
types together.
• Do not take apart the batteries, heat them, or throw them
into a fire.
• When using the remote control unit in the wireless
condition, be sure to unplug the remote cable from the
REMOTE CONTROL terminal on the monitor.
7
Installation
VCR or Laser Disc Player
To video inputs on
the plasma monitor
VIDEO
VIDEO
1
2
VIDEO
3
Document Camera
L(MONO)
R
Y
CB/PB
CR/PR
L(MONO)
R
IBM VGA or Compatibles
RGB
1
R/CR/PR
G/Y
Macintosh or Compatibles
(Desk top type)
B/CB/PB
HD
VD
L(MONO)
R
Monitor adapter for
Macintosh (supplied)
Signal cable (supplied)
RGB
3
(Digital RGB)
To Mini D-Sub 15 pin connector on the plasma monitor
CONTROL
LOCK
ON /OFF
REMOTE
CONTROL
EXTERNAL
CONTROL
DVD Player
Personal computer with a
digital RGB output
8
Connecting Your PC or Macintosh Computer
Connecting your PC or Macintosh computer to your plasma
monitor will enable you to display your computer’s screen
image for an impressive presentation. The plasma monitor
supports the signals described on page 47.
Connecting Your Document Camera
You can connect your plasma monitor to a document
camera. To do so, simply:
1. Turn off the power to your plasma monitor and
document camera.
To connect a PC, Macintosh or compatible graphics adapter,
simply:
2. Use a standard video cable to connect your document
camera to the Video input on your plasma monitor.
1. Turn off the power to your plasma monitor and computer.
3. Turn on the plasma monitor and the document camera.
2. If your PC does not support XGA/SVGA/VGA you will
need to install an XGA/SVGA/VGA graphics board.
Consult your computer’s instruction manual for your
XGA/SVGA/VGA configuration. If you need to install a
new board, see the manual that comes with your new
graphics board for installation instructions.
Note: Refer to your document camera instruction
manual for more information about your camera’s video
output requirements.
Connecting Your VCR or Laser Disc
3. The plasma monitor provides signal compatibility up to
VESA 1600
ן 1200 (UXGA). However, it is not recommended to use this resolution due to image
readability on the monitors 1365
ן 768 native pixel resolution panel.
Player
Use common RCA cables (not provided) to connect your
VCR or laser disc player to your plasma monitor. To make
these connections, simply:
4. Use the signal cable that’s supplied to connect your PC or
Macintosh computer to the plasma monitor. For Macintosh,
use the supplied monitor adapter to connect to your
computer’s video port.
1. Turn off the power to your plasma monitor and VCR
or laser disc player.
2. Connect one end of your RCA cable to the video output
connector on the back of yourVCR or laser disc player,
connect the other end to theVideo input on your plasma
monitor. Use standard RCA audio patch cords to
connect the audio from your VCR or laser disc player
to your plasma monitor (if yourVCR or laser disc player
has this capability). Be careful to keep your right and
left channel connections correct for stereo sound.
5. Turn on the plasma monitor and the computer.
6. If the plasma monitor goes blank after a period of inactivity,
it may be caused by a screen saver installed on the computer
you’ve connected to the plasma monitor.
When using a Macintosh with the plasma monitor, the
following four display standards are supported using the
included Macintosh adapter :
3. Turn on the plasma monitor and the VCR or laser disc
player.
13" fixed mode
16" fixed mode
19" fixed mode
21" fixed mode
The 19" fixed mode is recommended for the plasma monitor.
Note: Refer to yourVCR or laser disc player instruction
manual for more information about your equipment’s video
output requirements.
Connections with Equipment that
Connecting Your DVD Player
You can connect your plasma monitor to a DVD player.
To do so, simply:
has a Digital Interface
Connections can be made with equipment that is equipped
with a digital interface compliant with the DVI (Digital
Visual Interface) standard.
* Use a DVI 29-pin signal cable and the ferrite cores
(supplied) when making connections to the RGB3 IN (DVI)
connector of the main unit.
Note that the RGB3 IN(DVI) terminal does not support
analog RGB input source.
1. Turn off the power to your plasma monitor and DVD
player.
2. Use a standard video cable to connect your DVD player
to the Y, Cb, and Cr inputs on your plasma monitor.
Or use the DVD-player’s S-Video output. Use a
standard S-Video cable to connect to the S-Video input
on the plasma monitor.
Note:
1. Input TMDS signals conforming to DVI standards.
The TMDS input corresponds to 1 link.
3. Turn on the plasma monitor and the DVD player.
2. To maintain display quality, use a cable with a quality
prescribedbyDVIstandardsthatiswithin5metersinlength.
9
External Speaker Connections
VIDEO
VIDEO
1
2
VIDEO
3
L(MONO)
R
Y
CB/PB
CR/PR
L(MONO)
R
RGB
1
R/CR/PR
G/Y
RIGHT LEFT
B/CB/PB
HD
VD
L(MONO)
R
RGB
3
(Digital RGB)
SPEAKERS MUST
HAVE MORE THAN
7WATT RATING
OHM
CONTROL
LOCK
ON /OFF
IMPEDANCE
5
RIGHT LEFT
REMOTE
CONTROL
EXTERNAL
CONTROL
AC IN
External speakers may be connected to the plasma monitor
to reproduce sound from VIDEO, DVD or RGB signal
sources.
To connect external speakers directly to the plasma
monitor:
1. Strip the ends of the speaker wires.
2. Press down the tabs below the SPEAKERS terminals,
insert the speaker wire and release the tab to secure the
speaker wire connection:
External speakers may be connected directly to the
SPEAKERS terminals or indirectly by connecting a stereo
system amplifier to the audio outputs.
[a] Connect the right speaker (located at right side
of the monitor when viewed from the front)
positive (+) wire to RIGHT +.
[b] Connect the right speaker negative (–) wire to
RIGHT –.
CAUTION: Unplug the plasma monitor and all
connected components before connecting external
speakers. Use only speakers with 6-ohm impedance and
a power input rating of 7 watts or more.
[c] Connect the left speaker negative (–) wire to
LEFT–.
[d] Connect the left speaker positive (+) wire to
LEFT+.
10
Pin Assignments and Signal Levels for 15 pin RGB (Analog)
Pin No.
Signal (Analog)
5
4
3
2
1
1
2
3
Red
10
9
8
7
6
Green or sync-on-green
Blue
15 14 13 12 11
4
5
No connection
Ground
6
Red ground
7
Green ground
8
Blue ground
9
No connection
Sync signal ground
No connection
Bi-directional DATA (SDA)
Horizontal sync or Composite sync
Vertical sync
10
11
12
13
14
15
Data clock
Pin Configuration and Signal of the RGB 3 IN Connector (DVI Connector)
The unit is equipped with a type of connector commonly
used for both analog and digital.
(Functionally, this cannot be used for an
analog input.)
Pin No.
1
Signal (Digital)
T.M.D.S Data 2 -
T.M.D.S Data 2 +
T.M.D.S Data 2 Shield
No connection
No connection
DDC Clock
2
3
4
5
(TMDS can be used for one link only.)
RGB 3
6
7
8
9
DDC Data
1
9
2
3
4
5
6
7
8
25 26
No connection
T.M.D.S Data 1 -
T.M.D.S Data 1 +
T.M.D.S Data 1 Shield
No connection
No connection
+5V Power
10 11 12 13 14 15 16
27 28
29
17 18 19 20 21 22 23 24
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Ground
Hot Plug Detect
T.M.D.S Data 0 -
T.M.D.S Data 0 +
T.M.D.S Data 0 Shield
No connection
No connection
T.M.D.S Clock Shield
T.M.D.S Clock +
T.M.D.S Clock -
No connection
No connection
No connection
No connection
No connection
11
Basic Operations
POWER
DIGITAL ZOOM
Digital zoom specifies the picture position and enlarges
the picture.
To turn the unit ON and OFF:
1. Plug the power cord into an active AC power outlet.
1. Press the POINTER button to display the pointer. (
)
2. Press the POWER ON button (on the remote control
unit) to turn on the unit.
To change the size of the picture:
Press the ZOOM+ button and enlarge the picture.
The monitor’s POWER/STANDBY indicator will light
up (green) when the unit is on.
The pointer will change to resemble a magnifying
glass. (
)
3. Press the POWER OFF button (on the remote control
unit or the unit) to turn off the unit.
A press of the ZOOM- button will reduce the picture
and return it to its original size.
The monitor’s POWER/STANDBY indicator turns red
and the standby mode is set (only when turning off the
unit with the remote control unit).
To change the picture position:
Select the position with the LM
ᮤ ᮣ
buttons.
2. Press the POINTER button to delete the pointer.
VOLUME
To adjust the volume:
AUTO ADJUST
To adjust the size or quality of the picture
automatically:
1. Press and hold theVOLUME
button (on the remote
control unit or the unit) to increase to the desired level.
Press the AUTO ADJUST button.
2. Press and hold theVOLUME button (on the remote
control unit or the unit) to decrease to the desired level.
MUTE
To cancel the sound:
Information
Press the MUTE button on the remote control unit to cancel
the sound; press again to restore.
Ⅵ AUTO ADJUST ON setting
When RGB (still picture) input
is selected ...... Fine Picture, Picture ADJ, Position,
and Contrast will be adjusted
automatically.
DISPLAY
To check the settings:
1. The screen changes each time the DISPLAY button is
pressed.
When RGB (motion picture),
VIDEO, or Y/Pb/Pr (component) input
is selected ...... The screen size switches to ZOOM
mode automatically with the
superimposed caption displayed fully
only when the picture contains dark
areas above and below the picture.
2. If the button is not pressed for approximately three
seconds, the menu turns off.
12
To cancel the off timer:
OFF TIMER
To set the off timer:
1. Press the OFF TIMER button twice in a row.
2. The off timer is canceled.
The off timer can be set to turn the power off after 30, 60,
90 or 120 minutes.
1. Press the OFF TIMER button to start the timer at 30
minutes.
OFF TIMER0
2. Press the OFF TIMER button to the desired time.
3. The timer starts when the menu turns off.
→ 30 → 60 → 90 → 120 → 0
OFF TIMER30
Note:
After the power is turned off with the off timer ...
A slight current is still supplied to the monitor. When you
are leaving the room or do not plan to use the system for a
long period of time, turn off the power of the monitor.
To check the remaining time:
1. Once the off timer has been set, press the OFF TIMER
button once.
2. The remaining time is displayed, then turns off after a
few seconds.
3. When five minutes remain the remaining time appears
until it reaches zero.
OFF TIMER28
13
WIDE Operations
STADIUM size screen
Watching with a wide screen (manual)
With this function, you can select one of four screen sizes.
When watching videos or digital video discs
1. Press the WIDE button on the remote control unit.
2. Within 3 seconds ...
Press the WIDE button again.
The picture is expanded in the horizontal and vertical
directions at different ratios.
The screen size switches as follows:
* Use this for watching normal video programs (4:3) with a
wide screen.
→ ZOOM → NORMAL → FULL → STADIUM
When watching high definition video source
ZOOM size screen
1. Press the WIDE button on the remote control unit.
FULL size screen (16 : 9)
The picture is expanded in the horizontal and vertical
direction, maintaining the original proportions.
* Use this for theater size (wide) movies, etc.
The full size screen is displayed.
NORMAL size screen (4:3)
* The picture has the same size as video pictures (16 : 9).
The normal size screen is displayed.
* The picture has the same size as video pictures with a
4 : 3 aspect ratio.
FULL size screen
The image is expanded in the horizontal direction.
* Images compressed in the horizontal direction (“squeezed
images”) are expanded in the horizontal direction and
displayed on the entire screen. (Normal images are
expanded in the horizontal direction.)
14
FULL size screen
Watching computer images with a
wide screen
Switch to the wide screen mode to expand the 4 : 3 image
to fill the entire screen.
1.Press the WIDE button on the remote control unit.
2.Within 3 seconds ...
Press the WIDE button again.
The screen size switches as follows:
→ NORMAL → FULL
The image is expanded in the horizontal and vertical
direction.
When wide signals are input.
NORMAL size screen (4:3 or SXGA 5:4)
TRUE
The picture has the same size as the normal computer
image.
The image is true resolution.
FULL size screen
FULL
The image is expanded in the horizontal direction.
When wide signals are input.
Information
FULL size screen
Ⅵ Supported resolution
See page 47 for details on the display output of the
various VESA signal standards supported by the
monitor.
Ⅵ “PICTURE SIZE” setting
When the setting of “PICTURE SIZE” is OFF, the size
of RGB-input pictures will be TRUE in place of
NORMAL.
When “PICTURE SIZE” is set to “OFF”
The screen size switches as follows:
→ TRUE → FULL
Ⅵ When 852 (848) dot
ן 480 line wide VGA* signals with a vertical frequency of 60 Hz and
horizontal frequency of 31.7 (31.0) kHz are in-
put
TRUE size screen (VGA, SVGA 4:3)
Select an appropriate setting for RGB SELECT mode
referring to the“Table for Signals Supported” on page
47.
* “ IBM PC/AT” and “VGA” are registered trademarks
of IBM, Inc. of the United States.
The image is true resolution.
15
MULTI SCREEN Operations
Showing a couple of pictures on the
VIDEO1
RGB/PC1
screen at the same time
A
B
* An RGB-input picture may not be displayed in these modes,
depending on the input signal specifications.
1. Press the MULTI button to select a screen mode from
among single mode, side by side, and picture in picture.
VIDEO1
RGB/PC1
Side by side 1
A
B
VIDEO1
RGB/PC1
A
B
Selecting the input signals to be displayed
1. Press the SELECT button to make the desired picture
active.
ᮤ ᮣ
Press the cursor buttons
on the remote control
ᮣ
unit to switch either side by side 1 (with ) or side by
ᮤ
side 2 (with ).
2. Press the RGB/PC, VIDEO, or DVD/HD button.
Each press of the button changes the selection of the
input signal.
Note:
The INPUT SELECT button on the monitor can also
be used to change the selection.
Picture A and B on the above screen are not always of the
same height.
Side by side 2
Adjusting the OSM controls
1. Press the PROCEED button to display the MAIN
MENU.
VIDEO1
RGB/PC1
Sub screen
Main screen
2. Adjust the setting to your preference.
For details, see “OSM (On Screen Menu) Controls” on
page 17.
Note:
Picture in picture
During multi mode, Auto Adjust does not affect the screen.
VIDEO1
RGB/PC1
Information
Ⅵ Positioning on the screen (for side by side)
Depending on the input-signal selection,
positioning of the picture is settled as follows.
Pictures displayed
Main screen
Sub
screen
on the left ........VIDEO1, VIDEO2, VIDEO3, HD1/
DVD1/DTV1, or HD2/DVD2/
ᮤ ᮣ
Press the cursor buttons
on the remote control
unit to switch the position of the sub screen.
DTV2
Pictures displayed
on the right ...... RGB/PC1, RGB/PC2, RGB/PC3
VIDEO1
RGB/PC1
Ⅵ Positioning on the screen (for picture in
picture)
Pictures displayed
Main screen
Sub
screen
Main screen ....RGB/PC1, RGB/PC2, RGB/PC3
Sub screen...... VIDEO1, VIDEO 2, VIDEO 3,
HD 1/DVD 1/DTV 1, or HD 2/
DVD 2/DTV 2
2. If you wish to switch the setting of the picture, press
the SELECT button to make the desired picture active.
Each press of the SELECT button changes the selection
of the active picture.
Ⅵ Multi screen operations may not function
depending on the type of the RGB signals.
16
OSM(On Screen Menu) Controls
5. The change is stored until you adjust it again.
Menu Operations
6. Repeat steps 2 – 5 to adjust an additional item, or press
the EXIT button on the remote control unit to return to
the main menu.
The OSM window is displayed with respect to the
screen as shown on the diagram.
* Depending on the screen’s mode, the OSM may be
displayed slightly differently.
In the explanation, the OSM section is shown close up.
Note:The main menu disappears by pressing the EXIT
button.
MAIN MENU
PICTURE
SOUND
SCREEN
FUNCTION
OPTIONS
INFORMATION
SEL.
PROCEED OK
EXIT EXIT
The following describes how to use the menus and the
selected items.
1. Press the PROCEED button on the remote control unit
to display the MAIN MENU.
MAIN MENU
PICTURE
SOUND
SCREEN
FUNCTION
OPTIONS
INFORMATION
SEL.
PROCEED OK
EXIT EXIT
2. Press the cursor buttons L M on the remote control
unit to highlight the menu you wish to enter.
3. Press the PROCEED button on the remote control unit
to select a submenu or item.
PICTURE
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
TINT
R
:
:
G
PICTURE MODE
COLOR TEMP.
NR
MEMORY
2
OFF
:
SEL.
ADJ.
EXIT RETURN
4. Adjust the level or change the setting of the selected
ᮤ
ᮣ
item by using the cursor buttons
control unit.
on the remote
17
Main menu
Sub menu
Functions
Default
Reset
PICTURE
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
Adjusts the contrast.
Adjusts the brightness.
Adjusts the sharpness.
Adjusts the color.
Center
Center
Center
Center
Center
Yes
Yes
Yes
Yes
Yes
Yes
TINT
Adjusts the tint.
PICTURE MODE Sets the picture mode according to the VIDEO environment and
image software.
COLOR TEMP
NR
MEMORY
Adjusts the color temperature and white balance.
Reduces noise visible in image.
2*1
OFF
Yes
Yes
Main menu
Sub menu
Functions
Default
Reset
SOUND
BASS
TREBLE
BALANCE
Sets the bass.
Sets the treble.
Sets the left/right balance.
Center
Center
Center
Yes
Yes
Yes
Main menu
Sub menu
Functions
Default
Reset
SCREEN
V-POSITION
H-POSITION
V-HEIGHT
H-WIDTH
AUTO PICTURE
Adjusts the vertical position.
Adjusts the horizontal position.
Adjusts the vertical size.
Center
Center
Min
Yes
Yes
Yes
Yes
No
Adjusts the horizontal size.
Min
Turn this on to have the monitor automatically adjust “FINE PICTURE” OFF*1
and “PICTURE ADJ”.
FINE PICTURE
PICTURE ADJ.
Adjusts for flickering on the computer image.
Adjusts for striped patterns on the computer image.
Min*1
Yes
Yes
Center*1
Main menu
Sub menu
Functions
Default
Reset
FUNCTION
OSM
Turns the on-screen display (screen mode, etc.) off (when set to “OFF”). ON
When set to “ON”, the on-screen display is displayed.
Yes
OSM ADJ.
POWER MGT
Adjusts the vertical and horizontal positions of the menu display.
Sets the monitor for use as an energy-saving display when used with a OFF
computer.
1
Yes
Yes
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
In case of 4 : 3, sets the luminance of both sides.
Sets the picture to suit the movie.
3
ON
1
Yes
Yes
Yes
Adjusts the picture when the picture input from the RGB3 input
terminal is distorted.
Sets the picture to reduce burn-in of the display.
Resets all the settings (PICTURE, SOUND, SCREEN, FUNCTION,
etc.) to the factory default values.
2
LONG LIFE
RESET
*
Yes
—
—
Main menu
Sub menu
Functions
Default
Reset
3
OPTION
AUDIO INPUT
BNC SELECT
RGB SELECT
Sets the allocation of the audio connectors.
Sets the BNC connectors.
Sets the appropriate mode for the computer image.
*
Yes
Yes
Yes
RGB
AUTO
RGB (VGA signals), VIDEO (Moving picture), WIDE (WIDE VGA) DTV.
Sets the digital broadcasting (1080A,1080B) or the High Vision (1035I). 1080B
HD SELECT
No
PICTURE SIZE
Sets the picture size for RGB input.
ON
Yes
Main menu
Sub menu
Functions
Default
Reset
INFORMATION
FREQUENCY
Used to check the frequency and synchronizing polarities of the signal
currently being inputted.
—
—
LANGUAGE
Sets the language of the menus (Japanese, English, German, French, English
Swedish, Italian or Spanish).
No
No
COLOR SYSTEM Sets the VIDEO format (AUTO1, AUTO2, PAL, PAL-M, PAL-N, PAL60, AUTO1
SECAM, 4.43 NTSC or 3.58 NTSC).
*1 RGB/PC only.
*2 PLE: AUTO ORBITER: OFF INVERSE: OFF
*3 AUDIO1: VIDEO1 AUDIO2: HD/DVD1 AUDIO3: RGB1
18
4. Once the adjustment is completed ...
Picture Settings Menu
Press the EXIT button to return to the main menu.
Adjusting the picture
The contrast, brightness, sharpness, color and tint can be
adjusted as desired.
To delete the main menu, press the EXIT button once
more.
Note:If “CAN NOT ADJUST” appears ...
When trying to enter the PICTURE submenu, make sure
PICTURE MODE is set to MEMORY.
Example: Adjusting the contrast
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
Information
1. Use the L and M buttons to select “PICTURE”, then
press the PROCEED button. The “PICTURE” screen
appears.
Ⅵ Picture adjustment screen
CONTRAST ....Changes the picture’s contrast.
BRIGHTNESS. Changes the picture’s brightness.
SHARPNESS .. Changes the picture’s sharpness.
Adjusts picture detail of VIDEO
2. Use the L and M buttons to select “CONTRAST”.
PICTURE
display.
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
COLOR ........... Changes the color density.
TINT ................Changes the picture’s tint. Adjust for
natural colored skin, background, etc.
TINT
R
:
:
G
Ⅵ Adjusting the computer image
PICTURE MODE
COLOR TEMP.
NR
MEMORY
2
OFF
Only the contrast and brightness can be adjusted when
a computer signal is connected.
:
SEL.
ADJ.
EXIT RETURN
Ⅵ Restoring the factory default settings
Select “RESET” under the “PICTURE MODE” settings.
ᮤ
ᮣ
and buttons to adjust the contrast.
3. Use the
CONTRAST
ᮤ
ᮣ
* If neither the or button is pressed within 5 seconds,
the current setting is set and the previous screen
reappears.
19
Setting the picture mode according to the
brightness of the room
There are four picture modes that can be used effectively
according to the environment in which you are viewing
the display.
4. Once the adjustment is completed ...
Press the EXIT button to return to the main menu. To
delete the main menu, press the EXIT button once more.
Information
Example: Setting the “THEATER” mode
Ⅵ Types of picture modes
MEMORY ........The last picture adjustments are stored
here.
THEATER ........Set this mode when watching video in
a dark room.
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
1. Use the L and M buttons to select “PICTURE”, then
This mode provides darker, finer
pictures, like the screen in movie
theaters.
CONTRAST = 80% for RESET mode
BRIGHTNESS = 95% for RESET
mode
press the PROCEED button.
The “PICTURE” screen appears.
2. Use the L and M buttons to select “PICTURE MODE”.
NORMAL .........Set this mode when watching video in
a bright room.
PICTURE
This mode provides dynamic pictures
with distinct differences between light
and dark sections.
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
CONTRAST = 96% for RESET mode
RESET ............Use this to reset the picture to the
factory default settings.
TINT
R
:
:
G
PICTURE MODE
COLOR TEMP.
NR
MEMORY
2
OFF
:
SEL.
ADJ.
EXIT RETURN
3. To set to “THEATER” ...
ᮤ
ᮣ
Use the and buttons to select “THEATER”.
ᮤ
ᮣ
The mode switches as follows when the
buttons are pressed:
and
→ MEMORY ↔ THEATER ↔ NORMAL ↔ RESET ←
PICTURE MODE
:
THEATER
ᮤ
ᮣ
* If neither the or button is pressed within 5 seconds,
the current selection is set and the previous screen
reappears.
20
Setting the color temperature
Use this procedure to set color tone produced by the plasma
display.
4. Once the setting is completed...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
Example: Setting “1”
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
Information
Ⅵ Setting the color temperature
1 ......................High (bluer)
2......................... Middle (Standard)
3 ......................Low (redder)
1. Use the L and M buttons to select “PICTURE”, then
press the PROCEED button.
The “PICTURE” screen appears.
2. Use the L and M buttons to select “COLOR TEMP.”.
Ⅵ Restoring the factory default settings
PICTURE
Select “RESET” under the function menu. Note that this
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
also restores other settings to the factory defaults.
TINT
R
:
:
G
PICTURE MODE
COLOR TEMP.
NR
MEMORY
2
OFF
:
SEL.
ADJ.
EXIT RETURN
ᮤ
ᮣ
3. Use the and buttons to select “1”.
ᮤ
ᮣ
The mode switches as follows when the
buttons are pressed:
and
→ 1 ↔ 2 ↔ 3 ↔ PRO ←
* See page 22 to set “PRO”.
:
1
COLOR TEMP.
ᮤ
ᮣ
* If neither the or button is pressed within 5 seconds,
the current selection is set and the previous screen reappears.
21
Adjusting the color to the desired quality
Use this procedure to adjust the white balance for bright
pictures and dark pictures to achieve the desired color
quality.
4. Press the PROCEED button.
The “WHITE BALANCE” screen appears.
5. Use the L and M buttons to select “RED-GAIN”.
WHITE BALANCE
GAIN
RED
GREEN
BLUE
BIAS
RED
GREEN
BLUE
Example: Adjusting the “WHITE BALANCE”
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
1. Use the L and M buttons to select “PICTURE”, then
press the PROCEED button.
SEL.
ADJ.
EXIT RETURN
The “PICTURE” screen appears.
ᮤ
ᮣ
6. Adjust the white balance using the and buttons.
2. Use the L and M buttons to select “COLOR TEMP.”.
PICTURE
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
TINT
R
:
:
G
PICTURE MODE
COLOR TEMP.
NR
MEMORY
2
OFF
R-GAIN
:
ᮤ
ᮣ
* If neither the or button is pressed within 5 seconds,
the current setting is set and the previous screen reappears.
SEL.
ADJ.
EXIT RETURN
7. Once the adjustment is completed...
ᮤ
ᮣ
3. Use the and buttons to select “PRO”.
Press the EXIT button to return to the main menu. To
delete the main menu, press the EXIT button once more.
ᮤ
ᮣ
The mode switches as follows when the
buttons are pressed:
and
→ 1 ↔ 2 ↔ 3 ↔ PRO ←
Information
Ⅵ Adjusting the white balance
RGB-GAIN ....... White balance adjustment for signal
level
RGB-BIAS .......White balance adjustment for black
level
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
COLOR TEMP.
:
PRO
ᮤ
ᮣ
* If neither the or button is pressed within 5 seconds,
the current selection is set and the previous screen reappears.
22
Reducing noise in the picture
Use these settings if the picture has noise due to poor
reception or when playing video tapes on which the picture
quality is poor.
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
Example: Setting “NR-3”
Information
Ⅵ NR
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
* “NR” stands for Noise Reduction.
* This function reduces noise in the picture.
1. Use the L and M buttons to select “PICTURE”, then
press the PROCEED button.
Ⅵ Types of noise reduction
The “PICTURE” screen appears.
There are three types of noise reduction. Each has a
different level of noise reduction.
2. Use the L and M buttons to select “NR”.
The effect becomes stronger as the number increases
(in the order NR-1 → NR-2 → NR-3).
OFF ...............Turns the noise reduction function off.
PICTURE
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
TINT
R
:
:
G
PICTURE MODE
COLOR TEMP.
NR
MEMORY
2
OFF
:
SEL.
ADJ.
EXIT RETURN
ᮤ
ᮣ
3. Use the
and
buttons to select “NR-3”.
ᮤ
ᮣ
The mode switches as follows when the
buttons are pressed:
and
→ OFF ↔ NR-1 ↔ NR-2 ↔ NR-3 ←
:
NR-3
NR
ᮤ
ᮣ
* If neither the or button is pressed within 5 seconds,
the current selection is set and the previous screen
reappears.
23
To continue adjusting the sound ...
Repeat from step 2.
Sound Settings Menu
Adjusting the treble, bass and left/right
balance
The treble, bass and left/right balance can be adjusted to
suit your tastes.
4. Once the adjustment is completed ...
Press the EXIT button to return to the main menu. To
delete the main menu, press the EXIT button once more.
Note :If “CAN NOT ADJUST” appears...
Set “AUDIO INPUT” on the OPTION menu correctly.
Example: Adjusting the bass
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
Information
Ⅵ Sound settings menu
BASS ..............Changes the level of low frequency
1. Use the L and M buttons to select “SOUND”, then
press the PROCEED button.
sound.
TREBLE ..........Changes the level of high frequency
sound.
BALANCE .......Changes the balance of the left and
right channels.
The “SOUND” screen appears.
2. To adjust the bass ...
Use the L and M buttons to select “BASS”.
SOUND
BASS
TREBLE
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
BALANCE
L
R
this also restores other settings to the factory defaults.
SEL.
ADJ.
EXIT RETURN
ᮤ
ᮣ
3. Adjust the bass using the and buttons.
SOUND
BASS
TREBLE
BALANCE
L
R
SEL.
ADJ.
EXIT RETURN
ᮤ
ᮣ
* If neither the or button is pressed within 5 seconds,
the current selection is set and the previous screen reappears.
24
ᮤ
ᮣ
3. Adjust using the and buttons.
Screen Settings Menu
AdjustingthePosition,Size,FinePicture,PictureAdj
The position of the image can be adjusted and flickering
of the image can be corrected.
Example:Adjusting the vertical position in the normal
mode
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
V–POSITION
ᮤ
ᮣ
* If neither the or button is pressed within 5 seconds,
the current setting is set and the previous screen
reappears.
1. Use the L and M buttons to select “SCREEN”, then
press the PROCEED button. The “SCREEN” menu
appears.
Default settings (when RGB/PC is selected)
To continue making other computer image
adjustments ...
SCREEN
Repeat from step 2.
MODE
:
NORMAL
V–POSITION
H–POSITION
V–HEIGHT
H–WIDTH
AUTO PICTURE
FINE PICTURE
PICTURE ADJ.
4. Once all adjustments are completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
:
OFF
SEL.
ADJ.
EXIT RETURN
Information
* The settings on the SCREEN menu are not preset at the
factory.
Ⅵ When “AUTO PICTURE” is “OFF”
SCREEN
To select a mode ...
MODE
:
FULL
ᮤ
ᮣ
Use the and buttons to select a mode.
The mode switches as follows when the
buttons are pressed:
V–POSITION
H–POSITION
V–HEIGHT
H–WIDTH
ᮤ
ᮣ
and
→ NORMAL ↔ FULL ←
AUTO PICTURE
FINE PICTURE
PICTURE ADJ.
:
OFF
* The mode can also be switched by pressing the “WIDE”
button on the remote control unit.
SEL.
ADJ.
EXIT RETURN
2. To adjust the vertical position ...
When Auto Picture is off, the Fine Picture and the
Picture ADJ items are displayed so that you can adjust
them.
Use the L and M buttons to select “V-POSITION”.
SCREEN
MODE
:
NORMAL
V–POSITION
H–POSITION
V–HEIGHT
H–WIDTH
AUTO PICTURE
FINE PICTURE
PICTURE ADJ.
:
OFF
SEL.
ADJ.
EXIT RETURN
25
Function Settings Menu
Information
Setting the on-screen display
When using the monitor for presentations, etc., the monitor
can be set so that the input source, screen mode, etc., do
not appear.
Ⅵ Adjusting the Auto Picture
ON...................The Picture ADJ and Fine Picture
adjustments are made automatically.
OFF .................The Picture ADJ and Fine Picture
adjustments are made manually.
Example: Turning the on-screen display mode off
Ⅵ Adjusting the position of the image
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
V-POSITION ...Adjusts the vertical position of the
image.
H-POSITION ... Adjusts the horizontal position of the
image.
V-HEIGHT .......Adjusts the vertical size of the image.
(Except for STADIUM mode)
1. Use the L and M buttons to select “FUNCTION”, then
press the PROCEED button.
The “FUNCTION” screen appears.
H-WIDTH ......... Adjusts the horizontal size of the
image. (Except for STADIUM mode)
FINE PICTURE*.. Adjusts for flickering.
PICTURE ADJ* .... Adjusts for striped patterns on the
image.
2. Use the L and M buttons to select “OSM”.
FUNCTION
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
* The PictureADJ and Fine Picture features are available
only when the “Auto Picture” is off.
* TheAUTO PICTURE, FINE PICTURE and PICTURE
ADJ. are not available forVIDEO and HD/ DVD source.
SEL.
ADJ.
EXIT RETURN
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults
except for Auto Picture.
3. To turn the on-screen display mode off ...
ᮤ
ᮣ
Use the and buttons to select “OFF”.
ᮤ
ᮣ
The mode switches as follows each time the or
button is pressed:
ON ↔ OFF
FUNCTION
OSM
:
:
:
:
:
:
OFF
1
OFF
3
ON
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
SEL.
ADJ.
EXIT RETURN
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
Information
Ⅵ OSM modes
ON ...................The on-screen display appears.
OFF .................The on-screen display does not appear.
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
26
Adjusting the position of the menu display
Use these operations to adjust the position of the menus
that appear on the screen.
3. To adjust the position...
ᮤ
ᮣ
Adjust using the and buttons.
FUNCTION
OSM
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
:
:
:
:
:
ON
2
OFF
3
Example: Adjusting the position of the menu display
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
ON
RGB3 ADJ.
LONG LIFE
RESET
:
1
1. Use the L and M buttons to select “FUNCTION”,
then press the PROCEED button.
SEL.
ADJ.
EXIT RETURN
The “FUNCTION” menu appears.
2. Use the L and M buttons to select “OSM ADJ.”
FUNCTION
FUNCTION
OSM
OSM ADJ.
:
:
:
:
:
:
ON
1
OFF
3
ON
1
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
1
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
RESET
SEL.
ADJ.
EXIT RETURN
SEL.
ADJ.
EXIT RETURN
FUNCTION
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
4. Once all adjustments are completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
SEL.
ADJ.
EXIT RETURN
Information
Ⅵ Adjusting the position of the menu display
The position can be set
1 2 3
between 1 and 9.
4 5 6
7 8 9
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
27
Setting the power management for computer images
This energy-saving (power management) function
automatically reduces the monitor’s power consumption
if no operation is performed for a certain amount of time.
Information
Ⅵ Power management function
* The power management function automatically reduces
the monitor’s power consumption if the computer’s
keyboard or mouse is not operated for a certain amount
of time. This function can be used when using the
monitor with a computer conforming to the VESA
DPMS format.
Example: Turning the power management function on
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
* If the computer’s power is not turned on or if the
computer and selector tuner are not properly connected,
the system is set to the off state.
1. Use the L and M buttons to select “FUNCTION”, then
press the PROCEED button.
The “FUNCTION” screen appears.
* For instructions on using the computer’s power
management function, refer to the computer’s operating
instructions.
2. Use the L and M buttons to select “POWER MGT”.
FUNCTION
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
1
Ⅵ Power management settings
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
ON...................In this mode the power management
function is turned on.
OFF .................In this mode the power management
function is turned off.
SEL.
ADJ.
EXIT RETURN
Ⅵ Power management function and POWER/
STANDBY indicator
3. To turn the power management function on ...
The POWER/STANDBY indicator indicates the status
of the power management function. See page 29 for
indicator status and description.
ᮤ
ᮣ
Use the and buttons to select “ON”.
ᮤ
ᮣ
The mode switches as follows each time the or
button is pressed:
ON ↔ OFF
Ⅵ Restoring the factory default settings
FUNCTION
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
OSM
:
:
:
:
:
:
ON
1
ON
3
ON
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
SEL.
ADJ.
EXIT RETURN
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
28
POWER/STANDBY indicator
Power management POWER/STANDBY Power management
Description
Turning the picture back on
mode
indicator
operating status
Horizontal and vertical synchronizing Picture already on.
signals are present from the computer.
On
Green
Not activated.
No horizontal synchronizing signals Operate the keyboard or mouse. The
Standby
Suspend
Orange
Red
Activated.
Activated.
are sent from the computer.
picture reappears immediately.
No vertical synchronizing signals are Operate the keyboard or mouse. The
sent from the computer.
picture reappears, but more time is
required than from the standby
mode.
No horizontal or vertical synchronizing Operate the keyboard or mouse. The
signals are sent from the computer.
picture reappears, but more time is
required than from the standby mode
or suspend mode.
Off
Red
Activated.
29
Setting the gray level for the sides of the screen
Use this procedure to set the gray level for the parts on the
screen on which nothing is displayed when the screen is
set to the 4:3 size.
Setting the picture to suit the movie
The film image is automatically discriminated and
projected in an image mode suited to the picture.
[NTSC, PAL60, 480I(60Hz) only]
Example: Adjusting the “GRAY LEVEL”
Example: Setting the “CINEMA MODE” to “OFF”
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
1. Use the L and M buttons to select “FUNCTION”, then
press the PROCEED button.
1. Use the L and M buttons to select “FUNCTION”, then
press the PROCEED button.
The “FUNCTION” screen appears.
The “FUNCTION” screen appears.
2. Use the L and M buttons to select “CINEMA MODE”.
2. Use the L and M buttons to select “GRAY LEVEL”.
FUNCTION
FUNCTION
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
1
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
SEL.
ADJ.
EXIT RETURN
SEL.
ADJ.
EXIT RETURN
3. To set the CINEMA MODE to “OFF” ...
3. To adjust the “GRAY LEVEL”...
ᮤ
ᮣ
Use the and buttons to select “OFF”.
ᮤ
ᮣ
Use the and buttons to adjust the GRAY LEVEL.
ᮤ
ᮣ
The mode switches as follows each time the or
button is pressed:
FUNCTION
→ ON ↔ OFF ←
OSM
:
:
:
:
:
:
ON
1
OFF
9
ON
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
FUNCTION
OSM
:
:
:
:
:
:
ON
1
OFF
3
OFF
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
SEL.
ADJ.
EXIT RETURN
5. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
SEL.
ADJ.
EXIT RETURN
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
Information
Ⅵ GRAY LEVEL
Information
This adjusts the brightness of the black (the gray level)
for the sides of the screen.
The standard is 0 (black). The level can be adjusted
from 0 to 15. The factory setting is 3 (dark gray).
Ⅵ CINEMA MODE
ON...................Automatic discrimination of the
image and projection in cinema mode.
OFF ................... Cinema mode does not function.
Ⅵ Restoring the factory default settings
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
30
Setting RGB3 ADJ.
Reducing burn-in of the screen
The brightness of the screen, the position of the picture,
and positive/negative mode are adjusted to reduce burn-
in of the screen.
When the picture input from the RGB3 input terminal is
distorted, select the most appropriate setting from among
“1”, “2”, and “3”.
Example: Setting “2”
Example: Setting “PLE” to “LOCK”
Press the PROCEED button on the remote control unit to
display MAIN MENU on the screen, then...
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then proceed as
follows.
1. Use the L and M buttons to select “FUNCTION”,
then press the PROCEED button.
1. Use the L and M buttons to select “FUNCTION”, then
press the PROCEED button.
The “FUNCTION” screen appears.
The “FUNCTION” screen appears.
2. Use the L and M buttons to select “RGB3 ADJ.”.
2. Use the L and M buttons to select “LONG LIFE”, then
FUNCTION
press the PROCEED button.
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
FUNCTION
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
SEL.
ADJ.
EXIT RETURN
3. To select “2”...
PROCEED OK
SEL.
EXIT RETURN
Use the ᮤ and ᮣ buttons to select “2”.
The mode switches as follows each time the ᮤ or ᮣ
buton is pressed:
The “LONG LIFE” screen appears.
3. Use the L and M buttons to select “PLE”, then use the
→ 1 ↔ 2 ↔ 3 ←
ᮤ
ᮣ
and buttons to select “LOCK”.
FUNCTION
ᮤ
The mode switch changes as follows each time the
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
2
ᮣ
or button is pressed:
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
AUTO ↔ LOCK
LONG LIFE
PLE
ORBITER
INVERSE
:
:
:
LOCK
OFF
OFF
SEL.
ADJ.
EXIT RETURN
4. Once the setting is completed...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
SEL.
ADJ.
EXIT RETURN
4. Once the setting is completed...
Information
Press the EXIT button to return to the FUNCTION
menu.
To exit the main menu, press the EXIT button twice.
Ⅵ When you adjust the RGB3 ADJ.
The position of the menu display will change. In such
a case, be sure to adjust the position.
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
31
Resetting to the default values
Information
Use these operations to restore all the picture adjustments,
audio settings, to the factory default values.
Refer to page 18 for items to be reset.
Ⅵ PLE
AUTO .............. The brightness of the screen is
adjusted automatically to suit the
picture quality.
LOCK .............. The brightness level is set to
minimum.
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
1. Use the L and M buttons to select “FUNCTION”, then
press the PROCEED button.
Ⅵ ORBITER
ON...................The picture moves around the screen
intermittently.
The “FUNCTION” screen appears.
OFF .................Orbiter mode does not function.
2. Use the L and M buttons to select “RESET”, then press
the PROCEED button.
Ⅵ INVERSE
ON ..................... The picture is displayed alternately
between positive image and negative
image.
OFF .................Inverse mode does not function.
WT .................. The entire screen turns white.
FUNCTION
OSM
:
:
:
:
:
:
ON
1
OFF
3
ON
1
OSM ADJ.
POWER MGT
GRAY LEVEL
CINEMA MODE
RGB3 ADJ.
LONG LIFE
RESET
Ⅵ Restoring the factory default settings
Select “RESET” from the function menu. Note that this
also restores other settings to the factory defaults.
SEL.
EXIT RETURN
PROCEED OK
The “RESET” screen appears.
3. Use the L and M buttons to select “RESET”, then press
the PROCEED button.
RESET
RESET
RETURN
PROCEED OK
EXIT RETURN
RESET
SETTING NOW
When the “SETTING NOW” screen disappears, the
screen will be restored to the previous “RESET” mode,
then all the settings are restored to the default values.
4. Once the setting is completed ...
Press the EXIT button.
To delete the main menu, press the EXIT button once
more.
32
Setting the BNC connectors
Select whether to set the input of the 5 BNC connectors to
RGB or component.
Option Settings Menu
Setting the allocation of the audio connectors
Setting the AUDIO 1, 2, and 3 connectors to the desired
input.
Example: Set the BNC SELECT mode to “COMP.”
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
Example: Setting “AUDIO 1” to “VIDEO 2”
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
1. Use the L and M buttons to select “OPTION”, then
press the PROCEED button.
The “OPTION” screen appears.
1. Use the L and M buttons to select “OPTION”, then
press the PROCEED button.
2. Use the L and M buttons to select “BNC SELECT”.
The “OPTION” screen appears.
OPTION
2. Use the L and M buttons to select “AUDIO 1”.
AUDIO INPUT
AUDIO1
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
:
:
:
:
:
:
:
VIDEO1
HD/DVD1
RGB1
RGB
AUTO
1080B
ON
OPTION
AUDIO INPUT
AUDIO1
:
:
:
:
:
:
:
VIDEO1
HD/DVD1
RGB1
RGB
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
AUTO
1080B
ON
SEL.
ADJ.
EXIT RETURN
3. To set the BNC SELECT mode to “COMP.”...
SEL.
ADJ.
EXIT RETURN
ᮤ
ᮣ
Use the and buttons to select “COMP.”.
ᮤ
ᮣ
The mode switches as follows each time the or
button is pressed:
3. To set the AUDIO1 to “VIDEO2”...
ᮤ
ᮣ
Use the and buttons to select “VIDEO2”.
RGB ↔ COMP.
ᮤ
ᮣ
The mode switches as follows each time the or
button is pressed:
OPTION
→
VIDEO1
↔
VIDEO2
↔
VIDEO3
↔
HD/DVD1
↔
RGB/PC1
↔
RGB/PC2
↔
RGB/PC3
←
AUDIO INPUT
AUDIO1
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
:
:
:
:
:
:
:
VIDEO1
HD/DVD1
RGB1
COMP.
AUTO
1080B
ON
OPTION
AUDIO INPUT
AUDIO1
:
:
:
:
:
:
:
VIDEO2
AUDIO2
AUDIO3
HD/DVD1
RGB1
RGB
AUTO
1080B
ON
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
SEL.
ADJ.
EXIT RETURN
4. Once the setting is completed...
SEL.
ADJ.
EXIT RETURN
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
4. Once the setting is completed...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
Information
Ⅵ AUDIO INPUT
A single audio input cannot be selected as the audio
channel for more than one input terminal.
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
33
Setting a computer image to the correct RGB
select screen
With the computer image, select the RGB Select mode
for a moving image such as (video) mode, wide mode or
digital broadcast.
Information
Ⅵ BNC SELECT
RGB ................ Uses the 5BNC terminal for RGB
input.
COMP..............Use the 3BNC terminal for component
Example: Setting the “RGB SELECT” mode to
“MOTION ”
input.
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
1. Use the L and M buttons to select “OPTION”, then
press the PROCEED button.
The “OPTION” screen appears.
2. Use the L and M buttons to select “RGB SELECT”.
OPTION
AUDIO INPUT
AUDIO1
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
:
:
:
:
:
:
:
VIDEO1
HD/DVD1
RGB1
RGB
AUTO
1080B
ON
SEL.
ADJ.
EXIT RETURN
3. To set the RGB select mode to “MOTION” ...
ᮤ
ᮣ
Use the and buttons to select “MOTION”.
ᮤ
ᮣ
The mode switches as follows each time the or
button is pressed:
→ AUTO ↔ STILL ↔ MOTION ↔ WIDE1 ↔ WIDE2 ↔ DTV ←
OPTION
AUDIO INPUT
AUDIO1
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
:
:
:
:
:
:
:
VIDEO1
HD/DVD1
RGB1
RGB
MOTION
1080B
ON
SEL.
ADJ.
EXIT RETURN
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
34
Setting high definition images to the suitable
screen size
Use this procedure to set whether the number of vertical
lines of the input high definition image is 1035 or 1080.
Information
Ⅵ RGB SELECT modes
One of these 6 modes must be selected in order to
display the following signals correctly.
AUTO .............. Select the suitable mode for the
specifications of input signals as
listed in the table “Computer input
signals supported by this system” on
page 47.
Example: Setting the “1080B” mode to “1035I”
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
STILL .............. To display VESA standard signals.
(Use this mode for a still image from
a computer.)
1. Use the L and M buttons to select “OPTION”, then
press the PROCEED button.
The “OPTION” screen appears.
MOTION..........The video signal (from a scan
converter) will be converted to RGB
signals to make the picture more
easily viewable. (Use this mode for a
motion image from a computer.)
WIDE1.............When an 852 dot
ן 480 line signal with a horizontal frequency of
31.7kHz is input, the image may be
compressed horizontally. To prevent
this, set RGB SELECT to WIDE1.
2. Use the L and M buttons to select “HD SELECT”.
OPTION
AUDIO INPUT
AUDIO1
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
:
:
:
:
:
:
:
VIDEO1
HD/DVD1
RGB1
RGB
AUTO
1080B
ON
WIDE2.............When an 848 dot
ן 480 line signal with a horizontal frequency of 31.0
kHz is input, the image may be
compressed horizontally. To prevent
this, set RGB SELECT to WIDE2.
DTV .................Set this mode when watching digital
broadcasting (480P).
See page 47 for the details of the above settings.
SEL.
ADJ.
EXIT RETURN
3. To set the HD SELECT mode to “1035I” ...
ᮤ
ᮣ
Use the and buttons to select “1035I”.
ᮤ
ᮣ
The mode switches as follows each time the or
button is pressed:
→1080A ↔ 1080B ↔ 1035I ←
Ⅵ Restoring the factory default settings
OPTION
AUDIO INPUT
AUDIO1
AUDIO2
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
:
:
:
:
:
:
:
VIDEO1
HD/DVD1
RGB1
RGB
AUTO
1035I
ON
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
SEL.
ADJ.
EXIT RETURN
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
Information
Ⅵ HD SELECT modes
These 3 modes are not displayed in correct image
automatically.
1080A ............... Special Digital broadcasts (for
example : DTC100)
1080B ...............Standard digital broadcasts
1035I ...............Japanese “High Vision” signal format
35
Setting the picture size for RGB input signals
Use this procedure to switch the setting to “ON” or “OFF”.
Information Menu
Checking the frequencies, polarities of input
signals, and resolution
Example: Setting the “ON” mode to “OFF”
Use this function to check the frequencies and polarities
of the signals currently being input from a computer, etc.
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
1. Use the L and M buttons to select “OPTION”, then
press the PROCEED button.
The “OPTION” screen appears.
1. Use the L and M buttons to select “INFORMATION”,
then press the PROCEED button.
2. Use the L and M buttons to select “PICTURE SIZE”.
The “INFORMATION” screen appears.
OPTION
2. Use the L and M buttons to select “FREQUENCY”,
AUDIO INPUT
AUDIO1
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
:
:
:
:
:
:
:
VIDEO1
HD/DVD1
RGB1
RGB
AUTO
1080B
ON
then press the PROCEED button.
INFORMATION
FREQUENCY
LANGUAGE
COLOR SYSTEM
SEL.
ADJ.
EXIT RETURN
3. To set PICTURE SIZE mode to “OFF”...
ᮤ
ᮣ
Use the and buttons to select “OFF”.
EXIT RETURN
PROCEED OK
SEL.
ᮤ
ᮣ
The mode switches as follows when the or buttons
are pressed:
3. The frequency is displayed.
ON ↔ OFF
FREQUENCY
OPTION
H. FREQ
V. FREQ
: 37.5KHz
: 75.0Hz
AUDIO INPUT
AUDIO1
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
:
:
:
:
:
:
:
VIDEO1
HD/DVD1
RGB1
RGB
AUTO
1080B
OFF
H. POL
V. POL
: NEG.
: NEG.
MODE
RESOLUTION : 640
ן 480 : 8
EXIT RETURN
SEL.
ADJ.
EXIT RETURN
* Press the EXIT button to return to the previous screen.
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
4. Once you have checked the frequency ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
Information
Ⅵ PICTURE SIZE
ON ..................... For RGB Input: “NORMAL” and
“FULL” can be selected for Wide-
Screen switching.
OFF ................... For RGB Input: “TRUE” and
“FULL” can be selected for Wide-
Screen switching.
Ⅵ Restoring the factory default settings
Select “RESET” under the function menu. Note that
this also restores other settings to the factory defaults.
36
Setting the language for the menus
The menu display can be set to one of seven languages:
Japanese, English, German, French, Swedish, Italian or
Spanish.
Setting the video signal format
Use these operations to set the video signal format.
Example: Setting the video signal format to “3.58
NTSC”
Example: Setting the menu display to “DEUTSCH”
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
Press the PROCEED button on the remote control unit to
display the MAIN MENU on the screen, then...
1. Use the L and M buttons to select “INFORMATION”,
then press the PROCEED button. The
“INFORMATION” screen appears.
1. Use the L and M buttons to select “INFORMATION”,
then press the PROCEED button.
The “INFORMATION” screen appears.
2. Use the L and M buttons to select “LANGUAGE”,
then press the PROCEED button.
INFORMATION
2. Use the L and M buttons to select “COLOR SYSTEM”,
then press the PROCEED button.
FREQUENCY
LANGUAGE
INFORMATION
COLOR SYSTEM
FREQUENCY
LANGUAGE
COLOR SYSTEM
EXIT RETURN
PROCEED OK
SEL.
EXIT RETURN
PROCEED OK
The “LANGUAGE” screen appears.
SEL.
3. To select “ DEUTSCH ” ...
The “COLOR SYSTEM” screen appears.
ᮤ
ᮣ
Use the and buttons to select “ DEUTSCH ”.
ᮤ
ᮣ
The mode switches as follows when the
buttons are pressed:
and
COLOR SYSTEM
COLOR SYSTEM
→ ENGLISH ↔ DEUTSCH ↔ FRANÇAIS ←
:
AUTO1
→
↔ SVENSKA ↔ ITALIANO ↔ ESPAÑOL ←
LANGUAGE
LANGUAGE
:
DEUTSCH
ADJ.
EXIT RETURN
3. To select “3.58 NTSC” ...
ᮤ
ᮣ
Use the and buttons to select “3.58 NTSC”.
ᮤ
ᮣ
The mode switches as follows when the
buttons are pressed:
and
EXIT RETURN
ADJ.
PROCEED OK
4. Press the PROCEED button.
→ AUTO1 ↔ AUTO2 ↔ 3.58NTSC ↔ 4.43NTSC ←
→ SECAM ↔ PAL-M ↔ PAL-N ↔ PAL60 ↔ PAL ←
The display language is switched to Deutsch.
5. Once the setting is completed ...
COLOR SYSTEM
COLOR SYSTEM
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
:
3.58NTSC
Information
Ⅵ Language settings
ENGLISH ........English
DEUTSCH.......German
FRANÇAIS...... French
ESPAÑOL .......Spanish
ITALIANO ........Italian
SVENSKA .......Swedish
.............. Japanese
ADJ.
EXIT RETURN
37
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
The color system is set to “3.58 NTSC”.
Information
Ⅵ Video signal formats
Different countries use different formats for video
signals. Set to the format used in your current country.
AUTO1/2 ......... The video signals are automatically
detected and the format is set
accordingly.
AUTO1: 3.58NTSC, 4.43NTSC, PAL, SECAM,
PAL60
AUTO2: PAL-M, PAL-N, 3.58NTSC
PAL (B, G) .......This is the standard format used
mainly in the United Kingdom and
Germany.
SECAM............. This is the standard format used
mainly in France and Russia.
4.43 NTSC,
PAL60.............. This format is used for videos in
countries using PAL and SECAM
video signals.
3.58 NTSC ...... This is the standard format used
mainly in Japan and the United States.
PAL-M ............. This is the standard format used
mainly in Brazil.
PAL-N .............. This is the standard format used
mainly in Argentina.
38
External Control
Application
Communication Parameters
These specifications cover the communications control of
the plasma monitor by external equipment.
(1) Communication system
(2) Interface
Asynchronous
RS-232C
9600 bps
8 bits
(3) Baud rate
(4) Data length
(5) Parity
Connections
Connections are made as described below.
Odd
(6) Stop bit
1 bit
External equipment
e.g., Personal computer
(7) Communication code
Hex
plasma monitor
1) Connector on the plasma monitor side: EXTERNAL
CONTROL connector.
Type of connector: D-Sub 9-pin male
No. Pin Name
1
2
3
4
5
6
7
8
9
No Connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
1
5
9
6
2) Connector on the external equipment side: Serial port
(RS-232C) connector.
See the specifications of the equipment that is to be
connected for the type of connector and the pin
assignment.
3) Wiring
Use a crossed (reverse) cable.
Wire the cable so that each pair of data lines cross
between the two devices. These data line pairs are RXD
(Receive data) and TXD (Transmit data), DTR (DTE
side ready) and DSR (DCE side ready), and RTS (Ready
to send) and CTS (Clear to send).
39
Check Sum Example
Communication Format
DFH
Command
80H
60H
47H
01H
01H
08H
Check Sum
1
Unit ID 1 Unit ID 2 Command
2
Data Length Data
8 bit 8 bit 8 bit 8 bit 8 bit
8 bit 8 bit
8 bit
L
Command 1
Unit ID 1
Total
208H
Unit ID 2
2) Error Processing
Command 2
Data length
Data
• When the communication interval is vacant for more
than 4 ms, thereafter a received Command 1 will be
recognized. If, at this time, meaningful data cannot
be recognized, that data will not be recognized (as
valid data).
Check sum
• An ACK will not be returned unless the receive data
error, the check sum error, and the receive data are all
taken in.
Command 1
Command 1, along with command 2, is a number used to
distinguish each command.
In the case of ACK, when the lower order 4 bits is FH (as
in 3FH and 7FH), this indicates that the commands and
data of the supported equipment have been received. When
the lower order 4 bits is BH (as in 3BH and 7BH), this
indicates that unsupported commands and data have been
received.
Unit ID 1 and Unit ID 2
Unit ID 1 and unit ID 2 are numbers used to identify the
equipment that is to be connected.
60H is used for the plasma monitor and 80H is used for
external control equipment such as a personal computer.
1) Unit ID 1: Indicates the equipment sending the signal
2) Unit ID 2: Indicates the equipment receiving the signal
Command 2
Command 2, along with command 1, is a number used to
distinguish each command.
Check Sum (CKS), Error Processing, and ACK
1) The check sum described below and RS-232C odd
parity are used together for a check of the received data.
The check sum is the lower order 8 bits of one frame of
sent or received data comprising the sum total of
Command 1, Unit ID 1 and 2, Command 2, Data Length,
and Data.
40
03. Input Switch Change
Function
Command Reference List
The external control equipment switches the input of the plasma monitor.
CMD1 CMD2 LEN
Transmission Data
01. Power ON
9FH
9FH
DFH
DFH
DFH
9FH
9FH
DFH
DFH
DFH
DFH
DFH
DFH
1FH
1FH
DFH
DFH
DFH
DFH
1FH
DFH
1FH
DFH
1FH
4EH
4FH
47H
7FH
51H
3EH
3FH
58H
7FH
7FH
7FH
7FH
7FH
41H
54H
00H
7FH
7FH
7FH
45H
70H
6FH
6BH
3FH
00H
00H
01H
03H
01H
00H
00H
01H
03H
03H
03H
03H
03H
00H
00H
01H
04H
04H
04H
00H
02H
00H
03H
00H
DFH 80H 60H 47H 01H DATA00
CKS
02. Power OFF
03. Input Switch Change
04. VOLUME Gain Data
05. SCREEN MODE Select
06. AUDIO Mute On
07. AUDIO Mute Off
08. OSM Select
DATA00 : Input Select
01H: Video1
02H: Video2
03H: Video3
05H: HD (HD1 or DTV or DTV1)
06H: HD2 (DTV2)
07H: RGB1/PC1
09. Color Gain Data
10. TINT Gain Data
08H: RGB2/PC2
0CH: RGB3/PC3
11. SHARPNESS Gain Data
12. CONTRAST Gain Data
13. BRIGHT Gain Data
14. Input MODE Request
15. RESET
ACK
The plasma monitor returns the following ACK when the input is switched.
3FH 60H 80H 47H 00H CKS
04. VOLUME Gain Data
Function
The external control equipment changes the VOLUME gain data of the plasma
monitor.
16. COLOR TEMP SELECT
17. RED Gain Data
18. GREEN Gain Data
19. BLUE Gain Data
20. VIDEO ADJ Request
21. Audio Select Set
22. Audio Select Request
23. LONG LIFE Set
Transmission Data
DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 CKS
DATA00 USER SOUND Gain Flag
DATA01 VOLUME Gain Flag
DATA02 VOLUME Gain
05H
01H
00H: Step 0
24. Failure Mode Request
01. Power ON
Function
The external control equipment switches on the power of the plasma monitor.
0AH: Step 10 (Default)
2AH: Step 42
Transmission Data
ACK
9FH 80H 60H 4EH 00H CKS
7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
ACK
DATA00 USER SOUND Gain Flag
DATA01 VOLUME Gain Flag
05H
01H
The plasma monitor returns the following ACK when the power is switched on.
3FH 60H 80H 4EH 00H CKS
05. SCREEN MODE Select
Function
NOTE: Do not set the Power ON or Power OFF command
continuously.
The external control equipment switches the screen mode of the plasma monitor.
Transmission Data
02. Power OFF
Function
The external control equipment switches off the power of the plasma monitor.
DFH 80H 60H 51H 01H DATA00
CKS
DATA00 02H : STADIUM
03H : ZOOM
Transmission Data
04H : NORMAL
05H : FULL
9FH 80H 60H 4FH 00H CKS
06H : TRUE (REAL)
ACK
ACK
The plasma monitor returns the following ACK when the power is switched off.
7FH 60H 80H 51H 01H DATA00
CKS
3FH 60H 80H 4FH 00H CKS
DATA00 02H : STADIUM
03H : ZOOM
NOTE: Do not set the Power ON or Power OFF command
continuously.
04H : NORMAL
05H : FULL
06H : TRUE (REAL)
41
06. AUDIO Mute On
09. COLOR Gain Data
Function
Function
The external control equipment switches on AUDIO Mute of the plasma monitor.
The external control equipment changes the COLOR gain data of the plasma
monitor.
Transmission Data
Transmission Data
9FH 80H 60H 3EH 00H CKS
DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 CKS
ACK
DATA00: USER PICTURE Gain Flag
DATA01: COLOR Gain Flag
DATA02: COLOR Gain
* COLOR Gain is from -22 (EAH) to
+22 (16H) only during video.
01H
04H
E0H: -32
3FH 60H 80H 3EH 00H CKS
07. AUDIO Mute Off
Function
The external control equipment switches off AUDIO Mute of the plasma monitor.
FFH: -01
00H: 0
Transmission Data
01H: +01
9FH 80H 60H 3FH 00H CKS
20H: +32
ACK
ACK
3FH 60H 80H 3FH 00H CKS
7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
DATA00: USER PICTURE Gain Flag
DATA01: COLOR Gain Flag
01H
04H
08. OSM Select
Function
The external control equipment switches on or off the on-screen display (OSM)
of the plasma monitor.
10.TINT Gain Data
Function
The external control equipment changes the TINT gain data of the plasma
monitor.
Transmission Data
DFH 80H 60H 58H 01H DATA00
CKS
CKS
DATA00 01H : Screen display On
02H : Screen display Off
ACK
Transmission Data
DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 CKS
DATA00: USER PICTURE Gain Flag
DATA01: TINT Gain Flag
01H
05H
7FH 60H 80H 58H 01H DATA00
DATA02: TINT Gain
* TINT Gain is from -22 (EAH) to
+22 (16H) only during video.
E0H: -32
DATA00 01H : Screen display On
02H : Screen display Off
FFH: -01
00H: 0
01H: +01
Screen display On/Off is equivalent to the screen display On/Off
function of the convenient function settings.
*Operation is as described in the table below.
20H: +32
ACK
7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
DATA00: USER PICTURE Gain Flag
DATA01: TINT Gain Flag
01H
05H
On-Screen Display (OSD)
Operation
Display of items and adjustments on the menu Volume display, input display, and screen size display
When screen display is ON When screen display is OFF When screen display is ON When screen display is OFF
Remote control operation
Yes
No
Yes
No
Yes
Yes
No
No
Personal computer control operation
42
ACK
7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
11. SHARPNESS Gain Data
Function
The external control equipment changes the SHARPNESS gain data of the
plasma monitor.
DATA00: USER PICTURE Gain Flag
DATA01: BRIGHT Gain Flag
01H
08H
Transmission Data
DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 CKS
14. Input MODE Request
Function
DATA00: USER PICTURE Gain Flag
DATA01: SHARPNESS Gain Flag
DATA02: SHARPNESS Gain
01H
06H
F0H: -16
The display returns the current input information by the external control
equipment’ s request.
Transmission Data
FFH: -01
00H: 0
01H: +01
1FH 80H 60H 41H 00H CKS
ACK
7FH 60H 80H 41H 01H DATA00
CKS
10H:+16
DATA00: Input Select
ACK
01H: Video1
03H: Video3
05H: RGB1/PC1
0AH:DVD (DVD1)
0DH:DVD2
02H: Video2
04H: HD (HD1 or DTV or DTV1)
06H: RGB2/PC2
0CH:HD2 (DTV2)
0EH:RGB3/PC3
7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
DATA00: USER PICTURE Gain Flag
DATA01: SHARPNESS Gain Flag
01H
06H
12. CONTRAST Gain Data
Function
The external control equipment changes the CONTRAST gain data of the plasma
monitor.
15. RESET
Function
The external control equipment resets the user adjustment of the plasma
monitor.
Transmission Data
Transmission Data
DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 CKS
1FH 80H 60H 54H 00H CKS
DATA00: USER PICTURE Gain Flag
DATA01: CONTRAST Gain Flag
DATA02: CONTRAST Gain
01H
07H
CCH: -52
ACK
3FH 60H 80H 54H 00H CKS
FFH: -01
00H: 0
01H: +01
16. COLOR TEMP SELECT
Function
The external control equipment changes the COLOR TEMP of the plasma
monitor.
14H: +20
Transmission Data
ACK
DFH 80H 60H 00H 01H DATA00
CKS
CKS
7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
DATA00
00H: 1
01H: 2
02H: 3
03H: PRO
ACK
DATA00: USER PICTURE Gain Flag
DATA01: CONTRAST Gain Flag
01H
07H
13. BRIGHT Gain Data
Function
The external control equipment changes the BRIGHT gain data of the plasma
monitor.
7FH 60H 80H 00H 01H DATA00
Transmission Data
DATA00:
00H: 1
DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 CKS
01H: 2
02H: 3
03H: PRO
DATA00: USER PICTURE Gain Flag
DATA01: BRIGHT Gain Flag
DATA02: BRIGHT Gain
01H
08H
E0H: -32
NOTE: Set so that at the selection of 1, 2, or 3 of COLOR TEMP
change of the following R/G/B GAIN data cannot be accepted.
(This must be operated in the same way as OSD menu.)
FFH: -01
00H: 0
01H: +01
43
20H: +32
17. RED Gain Data
19. BLUE Gain Data
Function
Function
The external control equipment changes the RED Gain Data of the plasma
monitor.
The external control equipment changes the BLUE Gain Data of the plasma
monitor.
Transmission Data
Transmission Data
DFH 80H 60H 7FH 04H DATA00 to DATA03 CKS
DFH 80H 60H 7FH 04H DATA00 to DATA03 CKS
DATA00: USER PICTURE Gain Flag
DATA01: BLUE Gain Flag
DATA02: BLUE Gain1(Bias)
01H
03H
D8H:-40
DATA00: USER PICTURE Gain Flag
DATA01: RED Gain Flag
DATA02: RED Gain 1 (Bias)
01H
01H
D8H: -40
FFH:-1
00H: 0
FFH: -1
00H: 0
IEH: +30
D8H: -40
IEH: +30
D8H: -40
DATA03: BLUE Gain2(Drive)
DATA03: RED Gain 2 (Drive)
FFH:-1
00H: 0
FFH: -1
00H: 0
IEH:+30
IEH: +30
ACK
ACK
7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
DATA00: USER PICTURE Gain Flag
DATA01: BLUE Gain Flag
01H
03H
DATA00: USER PICTURE Gain Flag
DATA01: RED Gain Flag
01H
01H
18. GREEN Gain Data
Function
The external control equipment changes the GREEN Gain Data of the plasma
monitor.
Transmission Data
DFH 80H 60H 7FH 04H DATA00 to DATA03 CKS
DATA00: USER PICTURE Gain Flag
DATA01: GREEN Gain Flag
01H
02H
DATA02: GREEN Gain 1 (Bias)
D8H: -40
FFH: -1
00H: 0
IEH: +30
D8H: -40
DATA03: GREEN Gain2 (Drive)
FFH: -1
00H: 0
IEH: +30
ACK
7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
DATA00: USER PICTURE Gain Flag
DATA01: GREEN Gain Flag
01H
02H
44
20. VIDEO ADJ Request
Function
The display returns the video adjustments information by the external control
equipment’s request.
Transmission Data
DATA05: SHARPNESS Gain
DATA06: CONTRAST Gain
DATA07: BRIGHT Gain
F0H: -16
FFH: -01
00H: 0
01H: +01
1FH 80H 60H 45H 00H CKS
10H: +16
CCH: -52
ACK
7FH 60H 80H 45H 0CH DATA00 to DATA0B CKS
DATA00: RED Gain(Bias)
DATA01: GREEN Gain(Bias)
DATA02: BLUE Gain(Bias)
DATA03: COLOR Gain
D8H: -40
FFH: -01
00H: 0
01H: +01
FFH: -1
00H: 0
14H: +20
E0H: -32
IEH: +30
D8H: -40
FFH: -01
00H: 0
01H: +01
FFH: -1
00H: 0
IEH: +30
D8H: -40
20H: +32
D8H: -40
DATA08: RED Gain(Drive)
DATA09: GREEN Gain(Drive)
DATA0A: BLUE Gain(Drive)
DATA0B: COLOR TEMP
FFH: -1
00H: 0
FFH: -1
00H: 0
IEH: +30
E0H: -32
IEH: +30
D8H: -40
* COLOR Gain is from -22 (EAH) to
+22 (16H) only during video.
FFH: -01
00H: 0
01H: +01
FFH: -1
00H: 0
IEH: +30
D8H: -40
20H: +32
E0H: -32
DATA04: TINT Gain
FFH: -1
00H: 0
* TINT Gain is from -22 (EAH) to
+22 (16H) only during video.
FFH: -01
00H: 0
01H: +01
IEH: +30
20H: +32
00H: 1
01H: 2
02H: 3
03H: PRO
45
21. Audio Select Set
23. LONG LIFE Set
Function
Function
The external control equipment sets combinations of audio and video inputs
for the plasma monitor.
The external control equipment sets the PLE, ORBITER, and INVERSE (inverse
of image brightness) of the plasma monitor.
Transmission Data
Transmission Data
DFH 80H 60H 70H 02H DATA00 DATA01 CKS
DFH 80H 60H 6BH 03H DATA00 DATA01 DATA02 CKS
DATA00: AUDIO INPUT
DATA00 : PLE
01H:
02H:
03H:
AUDIO 1
AUDIO 2
AUDIO 3
01H:
02H:
AUTO
LOCK
DATA01 : INVERSE
DATA01: VISUAL INPUT
01H:
02H:
03H:
ON
OFF
WHITE
01H:
02H:
03H:
05H:
06H:
07H:
08H:
Video 1
Video 2
Video 3
HD (HD1 or DTV or DTV1)
HD2 (DTV2)
RGB 1/ PC 1
RGB 2/ PC 2
DATA02 : ORBITER (PICTURE SHIFT)
01H:
02H:
ON
OFF
ACK
The plasma monitor returns the following ACK when setting the PLE, ORBITER,
and INVERSE (inverse of image brightness):
0CH: RGB 3/ PC 3
ACK
3FH 60H 80H 6BH 00H CKS
The plasma monitor returns the following ACK when the input is switched.
3FH 60H 80H 70H 00H CKS
24. Failure Mode Request
Function
* The plasma monitor returns “Not Available” when selecting the
video input same as the one set at one of the AUDIO 01 to 3.
Example:
The plasma monitor returns “Not Available” when selecting the
VIDEO1 for AUDIO2 or VIDEO3 after VIDEO1 has been set to
AUDIO1.
The external control equipment inquires the detection of failures of the plasma
monitor.
Transmission Data
1FH 80H 60H 3FH 00H CKS
ACK
The plasma monitor returns the following ACK:
22. Audio Select Request
Function
The external control equipment inquires the current combinations of audio
and video inputs for the plasma monitor.
Transmission Data
7FH 60H 80H 3FH 02H DATA00 DATA01 CKS
DATA00: FAILURE MODE 1
Bit 0 : PDP MODULE
0: Abnormal
1: Normal
1FH 80H 60H 6FH 00H CKS
Bit 1 : 1: fixed (backup)
Bit 2 : TEMPERATURE
0: Abnormal
ACK
The plasma monitor returns the following ACK:
1: Normal
Bit 3 : FAN
7FH 60H 80H 6FH 03H DATA00 DATA01 DATA02 CKS
0: Abnormal
1: Normal
Bit 4 : 1: fixed (backup)
Bit 5 : 1: fixed (backup)
Bit 6 : 1: fixed (backup)
Bit 7 : 1: fixed (backup)
DATA00: AUDIO 1
DATA01: AUDIO 2
DATA02: AUDIO 3
VISUAL INPUT DATA
01H:
02H:
03H:
05H:
06H:
07H:
08H:
Video 1
Video 2
Video 3
HD (HD1 or DTV or DTV 1)
HD2 (DTV2)
RGB 1 /PC 1
RGB 2 /PC 2
DATA00:FILURE MODE 2
Bit 0–7 : 1: fixed (backup)
0CH: RGB 3 /PC 3
46
Table of Signals Supported
Supported resolution
• When the screen mode is NORMAL, each signal is converted to a 1024 dots
ן 768 lines signal. (Except for *2, 3, 4 • When the screen mode is TRUE, the picture is displayed in the original resolution.
• When the screen mode is FULL, each signal is converted to a 1364 dots
ן 768 lines signal. (Except for *3) )
Computer input signals supported by this system
Sync Polarity
Horizontal Vertical Horizontal Vertical
Presence
Screen mode
Vertical
Horizontal
frequency frequency
(Hz) (kHz)
70.1 31.5
RGB
Model
Dots
ן lines NORMAL TRUE FULL select*5
Signal Type
(4:3)
YES*2
YES
YES
YES
YES
YES
YES
– –
(16:9)
YES YES
640
ן 400 – –
NEG
NEG
NEG
NEG
NEG
NEG
NEG
POS
NEG
POS
POS
POS
POS
POS
POS
POS
NEG
NEG
POS
POS
NEG
POS
POS
POS
NEG
POS
POS
POS
POS
POS
POS
POS
NEG
NEG
NEG
NEG
NEG
NEG
NEG
POS
NEG
POS
POS
POS
POS
POS
POS
POS
NEG
NEG
POS
POS
NEG
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
– –
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
– –
640
ן 480 59.9
72.8
75.0
85.0
100.4
120.4
60.0
60.0
56.3
60.3
72.2
75.0
85.1
99.8
120.0
60.0
70.1
75.0
85.0
100.6
75.0
56.2
60.0
59.9
60.0
75.0
85.0
60.0
65.0
70.0
75.0
66.7
74.6
74.9
75.1
60.0
71.2
72.0
31.5
37.9
37.5
43.3
51.1
61.3
31.0
31.7
35.2
37.9
48.1
46.9
53.7
63.0
75.7
48.4
56.5
60.0
68.7
80.5
67.5
45.1
47.7
48.3
64.0
80.0
91.1
75.0
81.3
87.5
93.8
35.0
49.7
60.2
68.7
64.6
75.1
78.1
YES YES STILL
YES YES – –
YES YES STILL
YES YES
YES YES
YES YES
– –
– –
– –
848
ן 480 852
ן 480*1 800
ן 600 YES YES WIDE2
YES YES WIDE1
YES YES STILL
YES YES STILL
– –
YES
YES
YES
YES
YES
YES
YES
YES*3
YES*3
YES*3
YES*3
YES*3
YES
– –
YES YES
YES YES
YES YES
YES YES
YES YES
– –
– –
– –
– –
– –
*IBM PC/AT
compatible
computers
1024
ן 768 – – YES STILL
– – YES – –
– – YES STILL
– – YES
– – YES
– –
– –
1152
ן 864 1280
ן 768 1360
ן 765 1376
ן 768 1280
ן 1024 – – YES STILL
– – YES WIDE1
– – YES*3 WIDE1
– – YES WIDE2
– – YES STILL
– –
– –
YES*4
YES*4
YES*4
YES
YES
YES
YES
YES
YES
YES*3
YES
YES*4
YES*4
YES*4
– – YES
– – YES
– – YES
– – YES
– – YES
– – YES
YES YES
YES YES
– – YES
– – YES
– – YES
– – YES
– – YES
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
1600
ן 1200 640
ן 480 832
ן 624 *Apple
Sync on G Sync on G
Sync on G Sync on G
Sync on G Sync on G
Sync on G Sync on G
Macintosh*6
– –
– –
1024
ן 768 1152
ן 870 1280
ן 1024 – –
– –
– –
– –
Work Station
(EWS4800)
NEG
NEG
– –
NEG
NEG
– –
YES
YES
– –
YES
YES
– –
Work Station
(HP)
1280
ן 1024 – –
– –
Work Station
(SUN)
1152
ן 900 66.0
76.0
76.1
60.0
60.0
61.8
71.7
81.1
49.7
63.9
YES
YES
YES*4
YES*3
YES*4
– – YES
– – YES
– – YES
– – YES
– – YES
– –
– –
– –
– –
– –
C Sync
C Sync
C Sync
– –
C Sync
C Sync
C Sync
– –
– –
– –
– –
– –
1280
ן 1024 1024
ן 768 1280
ן 1024 – –
– –
Work Station
(SGI)
– –
– –
– –
– –
– –
– –
IDC-3000G
768
ן 576 50.0
59.9
31.4
31.5
YES*7
YES*7
– – YES*7
– –
NEG
NEG
NEG
NEG
YES
YES
YES
YES
PAL625P
NTSC525P
640
ן 480 – – YES*7 MOTION
47
*1 Only when using a graphic accelerator board that is capable of displaying 852
ן 480. *2 This signal is converted to a 1228 dots
ן 768 lines signal. *3 The picture is displayed in the original resolution.
*4 The aspect ratio is 5:4. This signal is converted to a 960 dot
ן 768 line signal. *5 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the
RGB mode prepared for the input signals listed in the table above.
*6 To connect the monitor to Macintosh computer, use the supplied monitor adapter (D-Sub 15-pin) to your computer's video
port. If your computer has a mini D-Sub 15-pin connector, you may have to use the supplied RGB cable.
*7 Other screen modes (ZOOM and STADIUM) are available as well.
NOTE:
• While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size
of the picture or the fine picture because of errors in synchronization of your computer.
• When a 1280 dot
ן 1024 line signal or 1600 dot ן 1200 line signal is input to the monitor, the picture will be compressed.
• This monitor has a resolution of 1365 dot
ן 768 line. It is recommended that the input signal should be XGA, wide XGA, or equivalent.
• With digital input some signals are not accepted.
• The sync may be disturbed when a nonstandard signal other than the aforementioned is input.
• If you are connecting a composite sync signal, use the HD terminal.
* “IBM PC/AT” and “VGA” are registered trademarks of IBM, Inc. of the United States.
* “Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.
48
Troubleshooting
If the picture quality is poor or there is some other problem, check the adjustments, operations, etc., before requesting service.
Symptom
Checks
Remedy
Picture is disturbed.
Sound is noisy.
• Is a connected component set directly in • Leave some space between the display and
front or at the side of the display?
the connected components.
Remote control unit operates
erroneously.
The remote control unit does not work. • Are the remote control unit’s batteries
worn out?
• Replace both batteries with new ones.
Monitor’s power does not turn on
when the remote control unit’s power
button is pressed.
• Is the monitor’s power cord plugged into a • Plug the monitor’s power cord into a power
power outlet?
outlet.
• Are all the monitor’s indicators off?
• Press the power button on the monitor to
turn on the power.
• Are the remote control unit’s batteries
worn out?
• Replace both batteries with new ones.
Monitor does not operate when the
remote control unit’s buttons are
pressed.
• Is the remote control unit pointed at the
monitor, or is there an obstacle between
the remote control unit and the monitor?
• Point the remote control unit at the monitor’s
remote control sensor when pressing
buttons, or remove the obstacle.
• Is direct sunlight or strong artificial light
shining on the monitor’s remote control
sensor?
• Eliminate the light by closing curtains,
pointing the light in a different direction, etc.
• Are the remote control unit’s batteries
worn out?
• Replace both batteries with new ones.
• The remote cable is plugged into the
REMOTE IN terminal (Wired).
• Unplung the remote cable from the monitor.
• The front panel buttons of the main unit
do not function.
• The front panel buttons do not function
during Control Lock.
No sound or picture is produced.
• Is the monitor’s power cord plugged into a • Plug the monitor’s power cord into a power
power outlet?
outlet.
Picture appears but no sound is
produced.
• Is the volume set at the minimum?
• Is the mute mode set?
• Increase the volume.
•
Press the remote control unit’s MUTE button.
• Are the speakers properly connected?
• Is AUDIO INPUT set correctly?
• Connect the speakers properly.
• Set AUDIO INPUT on the OPTION menu
correctly.
Poor picture with VIDEO signal input. • Improper control setting.
Local interference.
• Adjust picture control as needed.
Try another location for the monitor.
Be sure all connections are secure.
Cable interconnections.
Input impedance is not correct level.
Poor picture with RGB signal input.
• Improper control setting.
Incorrect 15 PIN connector pin
connections.
• Adjust picture controls as needed.
Check pin assignments and connections.
Tint is poor or colors are weak.
Nothing appears on screen.
• Are the tint and colors properly adjusted? • Adjust the tint and color (under “PICTURE”).
• Is the computer’s power turned on?
• Is a source connected?
• Turn on the computer’s power.
• Connect source to the monitor.
• Is the power management function in the
standby or off mode?
• Operate the computer (move the mouse,
etc.).
Part of picture is cut off or picture is
not centered.
• Is the position adjustment appropriate?
• Adjust the “SCREEN” properly.
Image is too large or too small.
• Is the screen size adjustment
appropriate?
• Press the “WIDE” button on the remote
control unit and adjust properly.
• Set to the proper resolution.
Picture is unstable.
• Is the computer’s resolution setting
appropriate?
POWER/STANDBY indicator is
lighted in orange or red.
• Horizontal and / or vertical sync signal is • Check the input signal.
not present when the Intelligent Power
Manager control is on.
POWER/STANDBY indicator is
blinking in red.
• The temperature inside the main unit has • Promptly switch off the power of the main
become too high and has activated the
protector.
unit and wait until the internal temperature
drops. See*1.
POWER/STANDBY indicator is
blinking in green.
• Prompty switch off the power of the main
unit. See *2.
——————
*1 Overheat protector
If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens., turn off the power to the
monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location and wait for the
monitor to cool for 60 minutes. If the problem persists, contact your Integra dealer for service.
*2 In the following case, power off the monitor immediately and contact your dealer or authorized Integra/Onkyo service station.
The monitor turns off 5 seconds after powering on and then the POWER/STANDBY indicator blinks. It indicates that the power supply circuit or, one or
more fans have been damaged.
49
Specifications
Product Name
Model Number
Screen Size
Plasma Monitor
PLA-50V1
1.89"
(48)
4.21"
(107)
48.8" (1240)
43.5"(H)
ן 24.5"(V) inches 1106(H)
ן 622(V) mm diagonal 50"
43.5" (1106)
Aspect Ratio
Resolution
Pixel Pitch
16 : 9
1365(H)
ן 768(V) pixels 0.032"(H)
ן 0.032"(V) inches 0.81(H)
ן 0.81(V) mm Color Reproduction
Signals
256 levels, 16,770,000 colors
Synchronization Range Horizontal : 15.5 to 93.8 kHz
(automatic : step scan)
4.2"
(107)
Vertical : 50.0 to 120 Hz
(automatic : step scan)
Input Signals
RGB, NTSC (3.58/4.43), PAL (B,G,M,N),
PAL60, SECAM, HD*1 , DVD*1 , DTV*1
Units are in inch
(mm)
Input Terminals
RGB
The features and specifications may be subject to change without
notice.
Visual 1 (Analog) mini D-sub 15-pin
ן 1 Visual 2 (Analog) BNC (R, G, B, H/CS, V)
ן 1 Visual 3 (Digital) DVI-I 29-pin
ן 1*2 (Not compatible with analog input)
Video
Visual 1
Visual 2
Visual 3
DVD/HD/DTV
Visual
Audio
External Control
*1HD/DVD/DTV input signals supported on this
system
RCA-pin
ן 1 BNC
ן 1 S
2-Video: DIN 4-pin
ן 1 480P (60 Hz)
525P (60 Hz)
625P (50 Hz)
720P (60 Hz)
480I (60 Hz)
525I (60 Hz)
625I (50 Hz)
1035I (60 Hz)
1080I (60 Hz)
RCA-pin (Y, PB[CB], PR[CR])
Stereo RCA
ן 3 D-sub 9-pin
ן 1(RS-232C) 7W+7W at 6 ohm
Sound output
Power Supply
Current Rating
Power Consumption
Dimensions
AC120V 50/60Hz
*2 It doesn’t cope with copy protection.
5.9A (maximum)
595W (typical)
48.8 (W)
ן 30.2 (H)ן 4.2 (D) inches 1240 (W)
ן 766 (H)ן 107(D) mm Weight
101.3 lbs / 46.0 kg
Environmental Considerations
Operating Temperature 0°C to 35°C / 32°F to 95°F
Humidity 20 to 80%
Storage Temperature -10°C to 50°C / 14°F to 122°F
Humidity 10 to 90%
Front Panel User Controls Power on/off, Input source select,
Volume up/down/ OSM control
Remote Control Functions Power on/off, Input source select, OSM
control,Volume up/down, Cursor (UP,
DOWN,LEFT, RIGHT), Pointer, Zoom up/
down, Off timer, Wireless/ Wired remote
control
Other Features
Accessories
Power management, plug and play (DDC1,
DDC2b, RGB3: DDC2b only), Control
lock, MULTI SCREEN operations
OSM Functions
Picture (Contrast / Brightness / Sharpness/
Color / Tint / Picture mode / Color
temperature/ Noise reductions), Sound (Bass
/ Treble/ Balance),Screen (V-Position / H-
Position/ V-Height / H-Width /Auto Picture
/ Fine picture/ Picture adjustment), Function
(OSM/ OSM adjustment/ Power
management/ Gray level/ Cinema mode/
RGB3Adjustment, Long Life (PLE, Orbiter,
Inverse)/ Reset)/Option (Audio input/ BNC
select/ RGBselect/ HD select/ Picture Size),
Information (Frequency / Language / Color
system)
Remote control unit with two AAA
batteries, Remote cable, Adapter for
Macintosh, RGB cable (Mini D-Sub 15-
pin to Mini D-Sub 15-pin connector),
Power cord, Instruction Manual,
Registration card, 7 Days Customer
service sheet, Safety metal fittings,
Screws for safety metal fittings,
Ferrite cores, Bands
Regulations
UL Approved (UL 1950/ CSA 950)
DOC Canada requirements
Meets FCC class A requirements
50
Integra Division of
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458 U.S.A
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div.:
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-833-5222
Printed in Japan
N0103-1
E
SN 29343119
|