T54A-toc.fm Page 1 Thursday, July 26, 2001 6:30 PM
Contents
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Handling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Workplace Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Adjusting the Monitor Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Working Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Connecting your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Switching on your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Configuring your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Setup Diskette for Windows 95, Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Setup Diskette for Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Auto Setup for DOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Auto Setup for Windows 3.1, Windows 95,
Windows 98, Windows NT or Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Manual Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Adjusting Your LCD Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
User controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
On-screen display (OSD) controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Further Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Display modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Product Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Further Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Compliances
1
T50_setup.fm Page 2 Thursday, August 9, 2001 11:09 AM
Setup
Hardware Requirements
This monitor requires a computer with a suitable on-board sub-system or
Video Adapter card that can support XGA 1024 × 768, SVGA 800 x 600, or
VGA 640 x 480 at 60 Hz.
Handling Instructions
Do not support the monitor
within the screen area. The
Liquid Crystal Display is
glass and can be damaged
by rough handling or
1. Lift the monitor by placing your hands where indicated below.
excessive pressure.
2. Before using your monitor for the first time, remove the clear protective
film from the front of the screen.
Workplace Preparation
This section gives advice
Height
on what you should
consider before you set up your
monitor.
The monitor should be positioned so that the top of the screen is slightly
below your eye level when you sit at your workstation.
Orientation
Choose a position that gives the least reflection from lights and windows,
usually at a right angle to any windows. The monitor should be positioned
directly in front of you so that you do not have to twist your body to use it. Tilt
the monitor to a comfortable viewing angle.
2
T50_setup.fm Page 3 Thursday, August 9, 2001 11:09 AM
Adjusting the Monitor Position
Viewing Angle
You can tilt the screen backward and forward as shown below.
Working Practices
This section gives
advice on how you can
work comfortably and reduce
fatigue.
Rest
Take regular breaks. Vary your posture, stand up and stretch occasionally as
prolonged use of computer workstations can be tiring.
Back
You should sit back in your chair and use the backrest.
Hands
Adjust the seat height so that your forearms are approximately horizontal and
your wrists are straight when using the keyboard. Your upper arms should be
relaxed with your elbows near your body.
Use a light touch on the keyboard, keeping your hands and fingers relaxed.
Allow a space in front of the keyboard to rest your wrists when not typing.
Consider using a wristpad.
3
T50_setup.fm Page 4 Thursday, August 9, 2001 11:09 AM
Eyesight
Working with monitors, in common with any prolonged close work, can be
visually demanding. Look away from the screen periodically and have your
eyesight checked regularly.
Screen settings
Set the screen brightness and contrast to a comfortable level. You may have
to adjust this as the lighting changes during the day. Many application
programs let you select color combinations which can help you to view in
comfort. See the User controls section for more information.
4
T50_setup.fm Page 5 Thursday, August 9, 2001 11:09 AM
Connecting your Monitor
Be sure to read the ‘Monitor
Safety and Warranty
1. Turn off your PC and all attached devices.
2. Connect the signal cable to the video port on the back of your computer.
This port might be directly attached to your computer (figure A), or it
might be part of a video adapter card (figure B). The video port on your
computer or video adapter card may be colored blue to match the blue
connector on your monitor’s video cable.
Information’ book before
carrying out this procedure.
The AC adapter and signal
cable are connected to
your monitor. If you wish to
change these or to fit a different
stand, see Further help section.
3. Connect the power cord to the power adapter first, then insert the plug
into a properly grounded electrical outlet.
Switching on your Monitor
1. Switch on the power source and your computer.
2. Switch on your monitor by pushing and releasing the power switch
marked
.
To switch off your monitor, push and release the power switch again.
3. Turn on the monitor and then the computer.
4. Run AUTO SETUP by following the instructions in the Configuring your
monitor section.
5
T50_setup.fm Page 6 Thursday, August 9, 2001 11:09 AM
Configuring your Monitor
Setup Diskette for Windows 95 or Windows 98
This section must be
completed before
continuing with the
Windows 95 or Windows 98
Auto Setup.
To use the Plug and Play feature in Windows 95 or Windows 98, files should
be loaded from the IBM Flat Panel Monitor Installation diskette:
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow the system to boot
into Windows 95 or Windows 98.
Your computer’s Plug and Play code may warn you that your system
hardware has changed. This probably means that it has detected your
new monitor for the first time.
4. Open the DISPLAY PROPERTIES window by clicking on START, SETTINGS,
CONTROL PANEL and then double clicking on the DISPLAY icon.
5. Select the SETTINGS tab.
On LCD monitors,
unlike CRTs, a faster
refresh rate does not
improve display quality.
IBM recommends using
either 1024 x 768 at a refresh
rate of 60Hz.
• In case of Windows 95:
6. -1. Select the Change Display Type button.
2. Select the Change Monitor Type button.
• In case of Windows 98:
6. -1. Select the ADVANCED BUTTON.
2. Select the MONITOR tab.
3. Open the UPGRADE DEVICE WIZARD windows by clicking on
Change button and then select the NEXT button.
If the UPGRADE DEVICE WIZARD is open go step 6-3. if not
continue to step 4.
4. Select the “Display a list of the known drivers for this device so that
I can choose a specific driver” and then select the NEXT button.
7. Insert the Setup diskette into drive A: and select the HAVE DISK button.
8. Select OK
.
9. Choose IBM T50 monitor and select OK. The files will be copied from the
diskette to your hard drive.
10. Close all open windows and remove the diskette.
11. Reboot the system.
The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
6
T50_setup.fm Page 7 Thursday, August 9, 2001 11:09 AM
Setup Diskette for Windows 2000
This section must be
completed before
continuing with the
Windows 2000 confguring
for your monitor.
To use the Plug and Play feature in Windows 2000, files should be loaded
from the IBM Flat Panel Monitor Installation diskette.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow the system to boot
into Windows 2000.
4. Open the DISPLAY PROPERTIES window by clicking on START, SETTINGS,
CONTROL PANEL and then double clicking on the DISPLAY icon.
5. Select the SETTINGS tab.
6. Select the ADVANCED button.
On LCD monitors, unlike
CRTs, a faster refresh rate
does not improve display
quality. IBM recommends using
either 1024 x 768 at a refresh
rate of 60Hz.
7. Select the MONITOR tab.
8. Select the PROPERTIFS button.
9. Select the Driver tab.
10. Open the Upgrade Device Driver Wizard window by clicking on
UPDATE DRIVER and then select the NEXT button.
11. select the “Display a list of the known dirvers for this device so that lcan
choose a specifc driver” and then sefect the NEXT button.
12. Inset the Setup diskette into drive A: and select the HAVE DISK button.
13. select OK.
14. Choose IBM T50 monitor and select OK. The files will be copied from the
diskette to your hard drive.
15. Close all open windows and remove the diskette.
16. Reboot the system.
The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
7
T50_setup.fm Page 8 Thursday, August 9, 2001 11:09 AM
Auto Setup
Auto Setup
Before carrying out this
section, it is very
important that The Setup
Diskette for Windows 95 or
Windows 98 has been run.
When you first use your monitor you must perform Auto Setup. This
procedure sets up your monitor to process the video signals from your
computer without image discoloration or smearing. After you perform Auto
Setup, the settings are stored and used each time you turn on the monitor.
In order to optimise the displayed image a set-up utility is provided on the IBM
Monitor Installation Diskette. Operation of the utility is dependent on the
operating system on your PC. For correct operation locate the operating
system on your PC from the table below and follow the appropriate
instructions. You may choose to run AUTO SETUP for each operating system
that you use. This means that if you sometimes use your monitor while
running any version of Windows and sometimes also use it from within DOS
(not a DOS window), you must run AUTO SETUP for both Windows and DOS.
You may run versions of AUTO SETUP in any order.
The Setup Utility
included on the setup
diskette is for displaying
dot patterns. They do not
replace or modify the display
dirver.
The Auto Setup instructions
require the monitor to be
warmed up for 15 minutes.
This is not required for normal
operation.
Operating System
DOS
Corresponding Auto Setup procedure
Auto Setup for DOS
Windows 3.1
Windows 95
Windows 98
Window 2000
Window NT
Auto Setup for Windows 3.1, Windows 95,
Windows 98, Windows 2000 or
Windows NT
If your PC does not run
with the setup diskettes
shipped with the monitor, refer
to Manual Setup.
Before you begin AUTO SETUP for your PC:
1. Make a backup copy of the setup diskettes supplied with the monitor.
2. Make sure the PC’s video mode is set in the range of the supported
screen resolution shown in the table.
The AUTO SETUP process
only applies to the current
screen mode. When a new
mode is selected, repeat this
section to reset the monitor
You should perform AUTO SETUP for each screen mode you use.
8
T50_setup.fm Page 9 Thursday, August 9, 2001 11:09 AM
Auto Setup for DOS
If the monitor is in standby
1. Turn on the monitor first; then the PC.
mode (STANDBY ON), it
may automatically turn off while
you are waiting for it to warm up.
If this happens, switch off the
monitor and switch it on again
after a few seconds.
If the message CHECK SIGNAL CABLE is displayed, or if nothing is
displayed check:
•
•
•
that the video interface cable is connected properly.
the correct video adapter card is installed.
the correct supported display mode is selected for your PC.
If you are using PC-DOS
IV, change to U.S. mode
by typing ‘CHEV US’ and
pressing ENTER at the
command prompt.
2. Wait approximately 15 minutes, until the monitor warms up.
3. Insert the diskette labelled ‘IBM Flat Panel Monitor Installation Diskette
into the diskette drive.
You must use DOS when
you run DOS Auto Setup.
4. Display the command prompt screen of the DOS full-screen display.
5. At the command prompt, type ‘A:’ and press ENTER.
6. Type ‘TESTPATD’ and press ENTER.
7. Select from the screen the number for the color or text mode you want to
setup.
8. Select from the screen the number for the video mode you want to
setup.
You may repeat this process for as many of the color and video modes
as you need.
The size and diversity of
the dot pattern varies with
the screen resolution.
9. When the dot pattern appears, press the OSD Enter button
at the
bottom of the monitor to display the initial OSD menu.
If the screen flickers,
repeat the setup several
times until the flicker is
minimised, or adjust it manually
by following Manual setup.
10. Use buttons ( - , +) to select the IMAGE LOCK icon
OSD Menu button to access the function.
11. Using buttons ( - , +), select AUTOMATIC and press the OSD Menu
button . This activates the AUTO SETUP procedure, which will optimize
then press the
the display settings with the provided dot-patterns.
The screen will be off several times and you may notice small changes
to the test pattern.
12. When finished, the OSD main menu returns. Press the Exit button to exit
from the OSD.
13. Press the ESCAPE key to exit the test pattern program.
14. Type ‘Exit’ at the command prompt to return to Windows.
If you use other operating systems, perform the appropriate AUTO SETUP for
those systems, also: see
Auto Setup for Windows 3.1, Windows 95, Windows 98, Windows NT or
Windows 2000.
9
T50_setup.fm Page 10 Thursday, August 9, 2001 11:09 AM
Auto Setup for Windows 3.1, Windows 95, Windows 98, Windows NT
or Windows 2000
If the monitor is in standby
mode (STANDBY ON), it
1. Turn on the monitor first; then the PC.
may automatically turn off while
you are waiting for it to warm up.
If the message CHECK SIGNAL CABLE is displayed, or if nothing is
displayed check:
•
•
•
that the video interface cable is connected properly.
the correct video adapter card is installed.
the correct supported display mode is selected for your PC.
2. Wait approximately 15 minutes, until the monitor warms up.
3. Drag the icon bar and tool bar, if they are displayed, to the bottom of the
screen.
4. Insert the diskette labelled ‘IBM Flat Panel Monitor Installation Disk’ into
the diskette drive.
The size and diversity of
the dot pattern varies with
the screen resolution.
5. Check the operating system installed on your PC and follow the
instructions from the table below.
Operating
System
Step1
Step2
Step3
Step4
Windows 3.1
Open
PROGRAM
MANGER
Select
FILE
Select
RUN
Windows NT 3.5
Type
‘A:\TESTPAT’
and press
ENTER
Windows 95
Select
START
Windows 98
Select RUN
Windows NT 4.0
6. When the test pattern appears, press the OSD Menu button
bottom of the monitor to display the initial OSD menu.
at the
Position the mouse pointer
at the bottom center of the
screen. This allows AUTO
SETUP to run properly
7. Use buttons ( - , +) to select the IMAGE LOCK icon
OSD Menu button to access the function.
8. Using buttons ( - , + ), select AUTOMATIC and press the OSD Menu
button . This activates the AUTO SETUP procedure, which will optimize
and press the
the display settings with the provided test pattern.
The screen will dim, blink on and off several times, and you may notice
small changes to the test pattern.
To abort the AUTO SETUP function, press the ESC key.
9. When finished, the OSD main menu returns. Press the Exit button once
to exit from the OSD.
10. Press the ESC key to return to Windows.
10
T50_setup.fm Page 11 Thursday, August 9, 2001 11:09 AM
You have completed the monitor setup for Windows. If you use other operat-
ing systems, perform the appropriate AUTO SETUP for those systems, also: see
Auto Setup for DOS.
11
T50_setup.fm Page 12 Thursday, August 9, 2001 11:09 AM
Manual Setup
Normally, you can complete the setup procedure using AUTO SETUP, however,
if your screen image is still distorted after you perform AUTO SETUP or the
setup diskette does not run on your system, perform MANUAL SETUP.
If the monitor is in standby
mode (STANDBY ON), it
might automatically turn off
while you are waiting for it to
warm up.
1. Have your monitor turned on for about 15 minutes, until the monitor
warms up.
2. Display the image you most frequently use on the screen.
3. Press the OSD Menu button
the initial OSD menu.
at the bottom of the monitor to display
4. Use buttons ( - , +) to select the IMAGE LOCK icon
OSD Menu button to access the function.
5. Using buttons ( - , +), select MANUAL, press
once to select COARSE. Left and right adjustment indicators become
illuminated
and press the
and then press “+
“
.
6. Use the buttons ( - , +) to manually adjust to correct (as much as
possible) for noise in the video signal then press Exit to save the
changes.
7. Use buttons ( - , +) to select FINE and press the
button.
8. Use the buttons ( - , +) again to tune the image to your liking.
9. When finished, press the Exit button four times to exit from the OSD.
You have completed the monitor setup.
12
T50_setup.fm Page 13 Thursday, August 9, 2001 11:09 AM
Adjusting Your LCD Monitor
User controls
User control features
Icon
Control
Auto
Description
Auto-adjust direct access
Displays the OSD main menu
Exits from menus and sub-menus
Exits the OSD
Exit
Adjust Button
Menu
highlight and adjust items in the menu.
- , +
Displays the OSD main menu
Enters menus and sub-menus and selects the
highlighted option
Power Switch
Switches the monitor on and off
Operation
The image is already
optimized for many display
modes, however the user
controls can be used to adjust
the image to your liking.
•
•
Press any of the OSD control buttons to display the main OSD menu.
Use the Adjust buttons to move among the icons. Select an icon and
press OSD Menu to access that function. If there is a sub-menu, you can
move between options using the Adjust buttons, then press OSD Menu to
select that function. Use the Adjust buttons to make adjustments.
13
T50_setup.fm Page 14 Thursday, August 9, 2001 11:09 AM
The settings are saved
•
Press the Exit button to move backwards through the sub-menus and exit
from the OSD.
after adjustment and when
exiting the OSD and will be
effective thereafter.
Note: After making adjustments, the Power indicator LED will briefly
turn amber to indicate that the new value has been saved.
OSD Lock / Unlock
This feature allows you to secure the current control settings, while allowing
the user to adjust Brightness and Contrast, so that they cannot be
inadvertently changed. You can unlock the OSD controls at any time by using
the same procedure.
Push and hold the OSD Menu button for 10 seconds to Lock or to Unlock.
When locked, a “LOCKED” message will be displayed.
14
T50_setup.fm Page 15 Thursday, August 9, 2001 11:09 AM
On-screen display (OSD) controls
The settings adjustable with the user controls are viewed through the On-
Screen Display (OSD). Press any of the OSD buttons to activate the OSD.
The LCD monitor needs
time to become thermally
Initial appearance of OSD
stable the first time you turn it on
each day. Thus, to achieve more
accurate adjustments for
MAIN MENU
parameters, allow the LCD
monitor to warm up (be On) for
at least 15 minutes before
making any screen adjustments.
i
BRIGHTNESS
OSD functions
Controls and
Adjustments
OSD Icon
Description
Sub-menu(s)
Adjusts brightness
BRIGHTNESS
CONTRAST
Adjusts contrast
The image lock function is used to
adjust the level of noise in the video
signal which causes horizontal lines or
areas on the screen where the image
appears to be unstable and jitters or
shimmers. This can be done
Automatic adjustment
Automatic
IMAGE LOCK
automatically or manually.
15
T50_setup.fm Page 16 Thursday, August 9, 2001 11:09 AM
Controls and
Adjustments
OSD Icon
Description
Sub-menu(s)
Manual -
Use the Adjust buttons
to adjust away the
interference. If
satisfactory results are
not obtained using the
Fine adjustment, use the
Coarse adjustment and
then use Fine again.
This function may
•
•
Fine
Coarse
IMAGE LOCK
(continued)
change the width of the
display image. Use the
H-Position function on
the Image Position
menu to center the
display image on the
screen.
Moves the screen left and right or up
and down.
H-Position
V-Position
Color Mode
IMAGE
POSITION
Select the Color Mode you find most
comfortable and then fine tune the
colors using the User Color Mode
menu, if necessary.
Mode 1
(Cool White)
COLOR
Mode 2
(Normal White)
Mode 3
(Warm White)
User Mode -
•
•
•
Red
Increases or decreases
redness
Green
Blue
Increases or decreases
greenness
Increases or decreases
blueness
16
T50_setup.fm Page 17 Thursday, August 9, 2001 11:09 AM
Controls and
Adjustments
OSD Icon
RESET
Description
Sub-menu(s)
Color Reset
Resets the Brightness, Contrast and
Color settings.
NO - Does not make the
adjustment
YES - Resets the color
Resets the Image position settings
Geometry
Reset
NO - Does not make the
adjustment
YES - Resets the
geometry
Shows information about the
addressability and the horizontal and
vertical frequencies of the images
received from the computer or video
board.
i
INFORMATION
The language chosen affects only the
language of the OSD. It has no effect
on any software running on the
computer.
Select one of the five
languages to use for the
OSD.
LANGUAGE
Changes the position of the OSD on
the screen.
H-Position
V-Position
OSD MENU
POSITION
17
T50_setup.fm Page 18 Thursday, August 9, 2001 11:09 AM
Further Information
Display modes
The display mode the monitor uses is controlled by the computer. Therefore,
you should refer to your computer documentation for details on how to
change display modes.
The image size, position and shape may change when the display mode
changes. This is normal and the image can be readjusted using AUTO SETUP
and the monitor controls.
Unlike CRT monitors, which require a high refresh rate to minimize flicker,
TFT technology is inherently flicker-free. If possible, configure your computer
for 1024 × 768 addressability at 60Hz vertical refresh rate.
For the display modes listed below, the screen image has been optimized
during manufacture.
Factory Set Display Modes
Addressability
Refresh Rate
Horizontal Frequency
640 × 350
640 × 480
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768†
1024 × 768
1024 × 768
70 Hz
60 Hz
72 Hz
75 Hz
70 Hz
75 Hz
72 Hz
60 Hz
56 Hz
60 Hz
70 Hz
75 Hz
31.5 kHz
31.5 kHz
37.9 kHz
37.5 kHz
31.5 kHz
46.9 kHz
48.1 kHz
37.9 kHz
35.2 kHz
48.4 kHz
56.5 kHz
60.0 kHz
† Recommended
‘Note: VESA timings are as detailed in the VESA “Display Monitor Timing
Specification”. Version 1.0, Revision 0.8, dated 09/17/98.’
18
T50_setup.fm Page 19 Thursday, August 9, 2001 11:09 AM
Power Management
If your computer has
previously been used
To benefit from power management, the monitor must be used in conjunction
with a computer that implements the Video Electronics Standards Association
(VESA) Display Power Management Signalling (DPMS) Standard.
with a CRT monitor and is
currently configured to a
display mode outside the
range that the Flat Panel
monitor can display, you
may need to re-attach the
CRT monitor temporarily
until youhave re-configured
the computer, preferably to
1024 x 768 at 60Hz.
The power management feature is invoked when the computer recognizes
that you have not used your mouse or keyboard for a user-definable period.
There are several states as described in the table below.
As an ENERGY STAR® Partner, IBM has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
IBM recommends that you switch off your monitor at the end of each working
day, or whenever you expect to leave it unused for long periods during the
day.
Power
Indicator
Restoring
Operation
State
Screen
Normal
Blank
Compliance
On
Steady green
Steady amber
®
Press a key or
move the mouse. ‡
ENERGY STAR
and NUTEK
Active Off
‡ There may be a slight delay before the picture reappears.
Product Disposal
The fluorescent lamp in the liquid crystal display contains mercury. Dispose of
it as required by local ordinances and regulations.
19
T50_setup.fm Page 20 Thursday, August 9, 2001 11:09 AM
Troubleshooting
If you have a problem setting up or using your monitor, you may be able to
solve it yourself. Before calling your retailer or IBM, try the suggested actions
that are appropriate to your problem.
Possible
Cause
Problem
Suggested Action
Reference
ꢀ
Ensure that the
electrical outlet and the
monitor are both switched
on.
ꢀ
Check that the power
cord is firmly plugged into
the electrical outlet and the
power supply unit.
Screen is blank
and power
indicator is off
Connecting
your monitor
section
No power to
monitor
ꢀ
If the power cord plug
has a removable fuse,
replace it.
ꢀ
Try another power
cord.
ꢀ
Try another electrical
outlet.
Screen is blank
and power
indicator is
Brightness
and Contrast
may be too
low
User controls
section
ꢀ
Adjust brightness and
contrast.
steady green
ꢀ
Press any key on the
Themonitoris
in the Power
Management
Standby or
Suspend or
Off state
keyboard or move the
mouse to restore
operation.
Screen is blank
and power
indicator is
Power
Management
section
ꢀ
Check the Power
steady amber
Management software on
your computer
20
T50_setup.fm Page 21 Thursday, August 9, 2001 11:09 AM
Possible
Cause
Problem
Suggested Action
Reference
ꢀ
Check that the signal
cable is firmly connected to
the computer.
Themonitor is
not receiving
a video signal
Connecting
your monitor
section
ꢀ
Check that no pins are
bent in the signal cable
connector.
Screen is blank
and power
indicator is
Flashing green
every 0.5
Display mode
of the
computer is
outside the
range of the
monitor
second
Further
information
section
ꢀ
Reconfigure the
computer to use a
supported display mode.
ꢀ
Select IMAGE LOCK
There are
noises in the
video signal
Image appears
to be smeared
User controls
section
menu in the OSD. Then
select MANUAL to adjust
FINE/COARSE settings.
Image appears
to be
discolored
The Color
setting may
be incorrect
User controls
section
ꢀ
Adjust the Color
settings.
For image problems, you
may want to run AUTO
ꢀ
The LCD contains over 2,300,000 thin-
A few dots are
missing,
discolored, or
inappropriately
lighted.
film transistors (TFTs). A small number of
missing, discolored, or lighted dots may be
present on the screen, which is an intrinsic
characteristic of the TFT LCD technology
and is not an LCD defect.
Setup again before consulting
to this section. In most cases,
AUTO SETUP can fix the
problems. See Auto Setup
section for details.
21
T50_setup.fm Page 22 Thursday, August 9, 2001 11:09 AM
Further Help
If you are unable to correct the problem yourself, you may seek further help
as follows:
Call the IBM HELPCENTER.
In the US call 1-800-772-2227
In Canada call 1-800-565-3344
In other countries contact your dealer, retailer, or other IBM authorized
Servicer.
If possible, stay by your
computer. Your Technical
Support Representative may
wish to go through the problem
with you during the call.
Before calling, please have available as much of the following information as
possible:
1. Model and serial number from the label on your monitor.
2. Purchase receipt.
3. Description of problem.
4. Computer type and model.
5. System configuration (hardware fitted, etc.).
6. System BIOS version number.
7. Operating System and version number.
8. Display driver version number.
9. Video Adapter Type.
More help, late-breaking
news and details of the
Removing the stand and cables
Alternative stands for your IBM Flat Panel Monitor may be available from
specialist suppliers.
latest accessories for these
products may be found on the
worldwide web at:
This product is equipped with mounting facilities that conform to the VESA
Flat Panel Monitor Physical Mounting Interface Standard (FPMPMI).
accessories
This product is shipped with the signal cable and the power cord attached to
the monitor. If you want to use other cables for reasons such as having the
monitor wall-mounted, follow the instructions below:
Information about the Video
Electronics Standards
Association can be found on the
worldwide web at:
1. Turn off the monitor and unplug it from the electrical outlet.
22
T50_setup.fm Page 23 Thursday, August 9, 2001 11:09 AM
2. Place the monitor panel-side down on a stable, padded, flat work
surface.
3. Remove the four mounting plate retaining screws. One screw at each
corner. Lift the base up and away from the monitor.
Attaching the stand and cables
1. Turn off the monitor and unplug it from the electrical outlet.
2. Place the monitor panel-side down on a stable, padded, flat work
surface
3. Align the screw holes on the swivel base with the corresponding holes
on the back of the monitor.
4. Insert and loosely secure the four screws on the base. Tighten the
screws in an alternating pattern and make sure not to over-tighten.
To obtain the correct cables and/or to get further instructions on installing
them, call the IBM HELPCENTER at the above numbers or contact your
dealer, retailer, or other IBM authorized Servicer.
23
T50_setup.fm Page 24 Thursday, August 9, 2001 11:09 AM
Specifications
This color monitor (Type-model 9511-AxC) uses a 15-inch TFT LCD
Dimensions
Width:
Depth:
Height:
364 mm
173 mm
400 mm
Weight
Tilt
Unpackaged:
packaged:
8.8 lb. (4.0 Kg)
11.5 lb (5.2 Kg)
Forward Tilt:
Backward tilt:
– 5°
+ 30°
Image
Viewable Image Size:
Maximum Height:
Maximum Width:
Pixel Pitch:
15.0” (381 mm)
228.1 mm
304.1 mm
0.297 mm (H) × 0.297 mm (V)
Power Input
Supply Voltage:
90 - 260 Vac
60/50 ± 3 Hz
1.0 A at 120 Vac
Max Supply Current:
Power consumption
figures are for the monitor
and the power supply
combined.
Power Consumption
Video Input
Normal Operation:
Active Off:
Off:
< 30 W
<
<
3 W
1 W
Input Signal:
Analog Direct Drive
75 ohm 0.7 V
Horiz. Addressability:
Vert. Addressability:
Clock Frequency:
1024 pixels (max)
768 lines (max)
78 MHz
Communications
VESA DDC:
2 B
Supported Display
Modes
VESA Standard 12 modes
See Display mode section
Environment
Temperature:
Operating:
Storage:
10 to 35° C
- 20 to 60° C
- 20 to 60° C
Shipping:
Humidity:
Operating:
Storage:
10 to 80%
5 to 95%
5 to 95%
Shipping:
24
T50_Compliance.fm Page I Wednesday, August 8, 2001 9:20 AM
Compliances
Federal
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Communications
Commission (FCC)
Statement
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult an IBM authorized dealer or service representative for help.
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits.
Proper cables and connectors are available from IBM authorized dealers. IBM is not responsible for any
radio or television interference caused by using other than recommended cables and connectors or by
unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could
void the user’s authority to operate the equipment.
Declaration of Conformity
Trade Name:
Model No.:
IBM Corporation
9511-AxC
Responsible Party:
Address:
Samsung Electronics Co., Ltd.
QA Lab of Samsung America
85 West Tasman Drive
San Jose, CA 95134 USA
408-554-5124
Telephone:
Fax:
408-554-5191
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Power Cords
For your safety, IBM provides a power cord with a grounded attachment plug to use with this IBM
product. To avoid electrical shock, always use the power cord and plug with a properly grounded power
outlet.
IBM power cords used in the United States and Canada are listed by the Underwriters Laboratories (UL)
and certified by the Canadian Standards Association (CSA).
For units intended to be operated at 115 volts: Use a UL listed and CSA certified cord set consisting of a
minimum 18 AWG, type SVT or SJT, three conductor cord, a maximum of 4.5 meters (15 feet) in length
and a parallel blade, grounding type attachment plug rated 15 amperes, 125 volts.
I
T50_Compliance.fm Page II Wednesday, August 8, 2001 9:20 AM
For units intended to be operated at 230 volts (U.S. use): Use a UL listed and CSA certified cord set
consisting of a minimum 18 AWG, type SVT or SJT, three conductor cord, a maximum of 4.5 meters (15
feet) in length and a tandem blade, grounding type attachment plug rated 15 amperes 250 volts.
For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a grounding type
attachment plug rated 13 amperes (minimum), 250 volts. The cord set should be marked <HAR> and have
the appropriate safety approvals for the country in which the equipment will be installed.
®
As an ENERGY
S
TAR Partner, IBM Corporation has determined that this product meets the ENERGY
S
TAR guidelines for energy efficiency.
MPRII
This product complies with Swedish National Council for Metrology (MPR) standards issued in December
1990 (MPRII) for very low frequency (VLF) and extremely low frequency (ELF).
II
T50_Svc.fm Page I Thursday, August 9, 2001 11:10 AM
Service Information
The following parts are for use by IBM service, or IBM authorised dealers, to support the
customer warranty. Parts are for service use only
.
9511 Flat Panel Monitor
31P6259
31P6260
31P6295
31P6294
04N8984
9511-AGC
9511-AWC
Flat Panel Monitor - Stealth Black
Flat Panel Monitor - Pearl White
Stand - Stealth Black
Stand - Pearl White
Power Supply
I
|