Instructions for Installation and Use
Hob
Models GF960, GF941
CONTENTS
Introduction
4
For Your Safety
Know your Hob
How to use your Hob
Practical Advice
Care and Cleaning
Troubleshooting
Installation
5
6
7
8-9
10
11
12-14
Electrical Connection
15
Characteristics of Burners and Nozzels
After Sales Service
Hotpoint Guarantee
16
18
19
Key Contacts
Back Cover
Retention of this Instruction Book
This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use
of the appliance.
If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book is also
provided so the new owner can become familiar with the appliance and safety warnings.
If the Book is lost or damaged a copy may be obtained from:
INDESIT Company UK LTD, Morley Way, Peterborough, PE2 9JB
3
Introduction
Your new hob is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been
installed in accordance with the installation instructions detailed in this booklet.
To help make best use of your cooking equipment, please read this booklet carefully.
The hob is designed specifically for domestic use and responsibility will not be accepted for use in any other installation.
* The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with this booklet.
(b) Has been properly connected to a suitable supply voltage as stated on the rating plate, attached to the
appliance.
(c) Has not been subjected to misuse or accident or been modified or repaired by any person other than the
manufacturers authorised employee or agent.
(d) Has been correctly installed.
This appliance conforms with the following European Economic Community directives:
-
-
-
-
-
73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications;
89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications;
93/68/EEC of 22/07/93 and subsequent modifications.
90/396/EEC of 29/06/90 (Gas) and subsequent modifications;
2002/96/EC
The European Directive 2002/96/EC onWaste Electrical and Electronic Equipment (WEEE), requires that old household
electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must
be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the
impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the appliance it must be separately collected.
Consumers should contact their local authority or retailer for information concerning the correct disposal of their old
appliance.
4
For Your Safety
When used properly your appliance is completely safe but as with any electrical product there are certain
precautions that must be observed.
PLEASE READ THE BELOW PRECAUTIONS BEFORE USING YOUR APPLIANCE.
To maintain the efficiency and safety of this appliance, we recommend you do the following:
- only call the Service Centres authorised by the manufacturer.
- always use genuine spare parts.
ALWAYS:
NEVER:
- make sure you remove all packaging and dispose of safely. - attempt to install or repair the appliance without the
- check the soundness of the appliance after it has been assistance of qualified personnel.
unpacked.
- store items above the appliance that children may attempt
- make sure you understand the controls before using the to reach.
appliance.
- heat up unopened food containers, as pressure can build
up causing the container to burst.
- keep children away from the appliance during use.
- take care to avoid heat/steam burns when operating the - use the appliance to heat up anything other than food.
controls. - use the appliance as a room heater.
- make sure the controls are turned off when you have finished - dry any items on the hob.
cooking and when not in use.
- install the appliance next to curtains or other soft furnishings.
- take care to avoid heat/steam burns when operating the - allow children to play with or tamper with the controls.
controls.
-leave children unsupervised where cooking appliances are
- disconnect from the power supply, and allow to cool, before installed as all the cooking surfaces get hot during and after
cleaning or performing maintenance.
use.
- refer servicing to a qualified appliance service engineer.
- store chemicals, foodstuffs or pressurised containers in or
- keep the hob clean as a build up of grease or fat from on the appliance, or in cabinets immediately above or next
cooking can cause a fire. to the appliance.
- follow the basic principles of food handling and hygiene to - use flammable or plastic items on or near the hob.
prevent the possibility of bacterial growth. - use adapters, multiple sockets and/or extension leads.
- dry food thoroughly before frying and lower it slowly into the - fill a deep fat frying pan more than 1/3 full of oil, or use a lid.
hot oil or fat. Frozen food in particular, will cause frothing and DO NOT LEAVE UNATTENDED WHILE COOKING.
spitting if added too quickly.
- keep outside of pans clean and free from streaks of oil or only lowers the temperature or the oil or fat too much, resulting
fat. in greasy food.
- fry too much food at a time, especially frozen food. This
- place pans centrally over the cooking areas making sure - pull on the appliance or the supply able to unplug it from
handles are kept away from the edge of the hob and cannot the electrical outlet.
be heated by other heating areas/pans.
- keep any ventilation slots clear of obstructions.
- allow power cables of other appliances to come into contact
with hot parts of this appliance.
- expose the appliance to atmospheric agents, such as
rain or sunlight.
- operate the appliance with wet hands.
- allow anyone to sit or stand on any part of the appliance.
- use misshapen pans which may be unstable.
- use round base woks directly on the gas pan supports.
- use fish kettles or large preserving pans across two gas
burners.
- operate the appliance with wet parts of the body.
- operate the appliance when barefoot.
SAFETY ADVICE
IMPORTANT - As with any cooking appliance there could be some fire risk attached to the heating of oil, particularly for
deep fat frying. Cooking utensils containing oil must not be left unattended (eg. to answer the telephone) on or in close
proximity to the cooking areas.
IN THE EVENT OF A CHIP PAN OR ANY OTHER PAN FIRE:
1. Turn off the burners.
2. Cover the pan with a fire blanket or damp cloth, this will smother the flames and extinguish the fire.
3. Leave the pan to cool for at least 60 minutes before moving it. Injuries are often caused by picking up a hot pan and
rushing outside with it.
NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force of the extinguisher is likely to tip the pan
over. Never use water to extinguish oil or fat fires.
5
Know your Hob
S
A
RR
TC
B
F
1
12
2
11
3
Model GF941V
Model GF941B
Model GF960
4
10
5
9
6
8
7
D
C
I
H
S
A
RR
TC
B
1
6
12
11
10
2
3
4
5
9
8
7
C
L
H
S
A
RR
TC
B
SP
C
B. Pan Support for Cookware
C. Control Knobs
D. Ignitor for Gas Burners
F. Flame Failure Device - Activates if the flame accidentally
goes out (spills, drafts, etc.), interrupting the delivery of
gas to the burner.
A.
Auxilliary Burner
RR Reduced Rapid Burner
S.
SP. Semi-Fish Kettle Burner
TC. Triple Crown Burner (Wok Burner)
Semi Rapid Burner
H. Indicator for Electric Hotplates - ( models GF941V
and GF941B only) - On those models equipped with
electric hotplates and ignitor, the indicator light is
incorporated into the ignition button.
I. Glass Ceramic Module - (model GF941V only)
L. Griddle - (model GF941B only).
NOTICE
The cast-iron grill, located in the burner and grate packing box, must be installed, below and above the electric heating
element so that the element is enclosed between the two.
6
How To Use Your Hob
The position of the corresponding gas burner is indicated on
each control knob.
Griddle (model GF941B only)
Thegriddlecanberegulatedbyturningthecorrespondingknob
in the clockwise or counter-clockwise direction to any of the 12
possible settings:
Gas Burners
The burners differ in size and power. Choose the most
appropriate one for the diameter of the cookware being used.
The burner can be regulated with the corresonding control
knob by using one of the following settings:
• Off
0
1
Off
Low
2-11 Medium
12 High
When the knob is on any of the settings other than "Off", the
"H" operating light comes on.
High
Low
Ceramic Glass Module(model GF941V)
On those models fitted with an ignitor (D),
To light a burner, simply press the corresponding knob all
the way in and then turn it in the counter-clockwise direction
to the "High" setting, keeping it pressed in until the burner
lights.
As they are fitted with a flame failure device (F), the
knob must be pressed in for about 6 seconds until the device
that keeps the flame lighted warms up.
Caution: If the burner accidently goes out, turn off the gas
with the control knob and try to light it again after waiting at
least 1 minute.
To turn off a burner, turn the knob in the clockwise direction
until it stops (it should be on the “•” setting).
This cooktop is fitted with dual-ring radiant heating elements
located beneath the glass. It is possible to turn on only the
circular part of the elemement (identified by the letter "A") or the
cooking surface can be enlarged by turning on both "A" and
"B". Toturnonlythecircular"A"element, simplyturntheknobin
the clockwise direction to any one of the 12 available settings.
To add the "B" section, turn the knob to setting 12 and then click
it into the
setting. Then proceed by turning the knob in the
counter-clockwise direction to one of the 12 settings.
The figure shows the heating zones, which become red when
the element is turned on.
A. Circular heating zone;
B. Extended heating zone;
C. Indicator light to show when the cooking zone is above
60°C, even after the heating element has been turned off.
C
A
B
When the knob is on any of the settings other than "Off", the
"H" operating light comes on.
7
Practical Advice
Practical Advice on Using the Half Fish-Kettle Burner
Practical Advice on Using the Burners
For best performance, follow these general guidelines:
The two central burners, or Half Fish-Kettle burners, are eliptic
in form and can be turned up to 90°. This makes the hob
more flexible in terms of how it can be used.
•
Use the appropriate cookware for each burner (see
table) in order to prevent the flame from reaching the
sides of the pot or pan;
•
•
Alwasy use cookware with a flat bottom and keep the
lid on;
When the contents come to a boil, turn the knob to
"Low".
To turn the two central burners 90°, proceed as follows:
Burner
Cookware Diameter
(cm)
24 - 26
24 - 26
16 - 20
•
•
•
•
Make sure that the burners are cool;
Lift the burner completely out of its housing;
Replace it in its housing in the position desired;
Make sure that the burners are positioned correctly before
use.
Rapid (R)
Reduced Rapid (RR)
Semi-Rapid (S)
Auxilliary (A)
10 - 14
Semi-Fish Kettle (SP)
Triple Crown (TC)
16 - 20
24 - 26
In addition, the two cetnral burners can be used in tandem
or speartely with cookware of different shapes and sizes:
•
•
Double burner for a fish-kettle or oval cookware (Fig. A).
Double burner for a griddle or rectangular/square
cookware with minimum dimensions of 28x28 cm (Fig. B)
Double burner for large cookware (diameter of 26-28 cm)
(Fig. C).
To identify the type of burner, refer to the 'Burner and Nozzle
Specifications' section.
•
•
Single burner for medium size cookware (diameter of 16-
20 cm) (Fig. D).
Fig. A
Fig. B
Fig. C
Fig. D
8
Practical Advice
Practical Advice on Using the Griddle
Preheat the griddle by turning the knob to 12. Settings 1-8
are recommended for reheating food or for keeping it warm
after it has been cooked. In general, cooking vegetables
can cause stains which are difficult to remove.
Weight
(kg)
Knob Preheati- Cooking Time
Food
Setting ng (min.)
(min.)
12
15
20
Pork
Chops
0.5
5
10
Steak
0.6
0.45
0.4
12
10
12
10
11
5
5
5
5
5
10
20
14
15
2
Sausages
Shish Kabobs
(meat)
Hamburgers
0.4
Toasted
Sandwiches
No. 3
Bread
3 Slices
3 Slices
11
12
5
5
3
Aubergines
5 – 7
Oven-roasted
Tomatoes
No. 4
12
5
10 – 15
Practical Advise on Using the Ceramic Glass Module
For best performance, keep in mind the following:
•
All types of casseroles can be used on the ceramic glass
cooking surface. However, it is important that the bottom
be perfectly flat. Casseroles with thicker bottoms distribute
heat more evenly.
Set. Radiant Burner
0
1
Off
To melt butter and chocolate.
2
•
Use cookware the diameter of which is at least as large
as the cooking area so that all of the heat produced by
the heating element is used.
To heat liquids.
3
4
For creams and sauces.
For cooking at the boiling point.
For roasts.
5
6
•
•
Make sure that the bottom of the pot is always dry and
clean to insure good contact between the cookware and
the cooking surface. This will also increase the life of the
pots and of the ceramic glass surface as well.
Do not use the same cookware that you use for gas
burners because the concentrated heat they produce can
deform the bottom of the pot. Therefore, you will not
achieve best results when using these pots on the
ceramic glass surface.
7
8
9
10
11
For boiling large pieces of meat.
12 For frying.
For utilising both cooking areas.
Notice: The glue used to seal the glass surface may leave
traces on the appliance. We recommend that the module be
cleaned with a non-abrasive cleaner before being used the
first time. During the first few hours of use, you may detect
the smell of rubber; this will disappear after a short time.
9
Care and Cleaning
Before cleaning or performing maintenance on your hob,
disconnect it from the power supply.
To extend the life of the hob, it should be cleaned
carefully and thoroughly on a frequent basis, keeping in
mind the following:
• When cleaning the griddle, it is recommeded that you do
so while it is still hot, using the handles provided to move
it from the hob to the sink. To remove the pan beneath
the griddle, it is a good idea to wait until the heating element
has cooled (roughly after 15 minutes).
·
•
Do not use steam equipment to clean the appliance.
The enamelled parts must be washed with warm water
without using abrasive powders or corrosive substances
which could ruin them.
•
•
•
The removable parts of the burners should be washed
frequently with warm water and soap, making sure to
remove caked-on substances.
On hobs with automatic ignition, the end of the electronic
ignition device must be cleaned carefully and frequently,
making sure that the gas holes are not clogged.
Stainless steel can be stained if it remains in contact
with highly calcareous water or aggressive detergents
(containing phosphorous) for an extended period of time.
It is recommended that these parts be rinsed thoroughly
with water and then dried well. It is also a good idea to
clean up any spills.
•
Before using the ceramic glass module, the surface should
be cleaned , using a damp cloth to remove dust or food
residue. It must be cleaned regularly with a solution of
warm water and a non-abrasive detergent. First, remove
all food build up or grease with a cleaning scraper - not
supplied (Fig.A).
Greasing theTaps
The taps may jam in time or they may become difficult to
turn. If so, the tap itself must be replaced.
N.B.:This operation must be performed by a technician
authorised by the manufacturer.
Clean the cooking surface when it is still warm with a
suitable cleaning product, rub with a clean damp cloth
and dry. Sugar or foods with a high sugar content that
have melted onto the surface must be removed
immediately with a scraper while the surfacr is still hot. DO
NOT use abrasive sponges or cleaning products under
any circumstances. This holds true for chemically
aggressive cleaners, like oven sprays and stain removers.
Fig. A
1 0
Troubleshooting
Before calling service for assistance, check through the
If the burner does not remain on when set to "Low".
following list, there may be nothing wrong.
Check to make sure that:
First of all, check to see that there are no interruptions in the
gas and electrical supplies, and, in particular, that the gas
valves for the mains are open.
•
•
•
The gas holes are not clogged.
There are no draughts near the cooking surface.
The minimum has been adjusted correctly (see Installation
section, "Minimum Regulation").
If the burner does not light or the flame is not uniform
around the burner.
If the cookware is not stable.
Check to make sure that:
Check to make sure that:
•
•
The gas holes on the burner are not clogged.
All of the movable parts that make up the burner are
mounted correctly.
•
•
•
The bottom of the cookware is perfectly flat.
The cookware is centered correctly on the burner .
The support grids have not been inverted.
•
There are no draughts around the cooking surface.
If, despite all of these checks, the hob does not function
properly and problem persists, call Hotpoint Service (see
KEY CONTACTS, back page), informing them of:
- The type of problem.
- The abbreviation used to identify the model (Mod. ...) as
indicated on the warranty.
If the flame does not stay lit on a model with the
Flame Failure device.
Check to make sure that:
•
•
You press the knob all the way in.
You keep the knob pressed in long enough to activate
the flame failure device.
•
The gas holes are not clogged in the area corresponding
to the flame failure device.
IMPORTANT:
Never call upon technicians not authorized by the
manufacturer, and refuse to accept spare parts that are not
original.
1 1
Installation
Thefollowinginstructionsareintendedfortheinstallersothatthe
d) Liquidifiedpetroleumgasesareheavierthanairand,asaresult,
settle downwards. Rooms in which LPG tanks are installed
mustbefittedwithventilationopeningstotheoutsideinorderto
allowthegastoescapeintheeventofaleak. Therefore, LPG
tanks, whether empty or partially full, must not be installed or
storedinroomsorspacesbelowgroundlevel(cellars,ect.).Itis
alsoagoodideatokeeponlythetankcurrentlybeingusedin
theroom,makingsurethatitisnotnearsourcesofheat(ovens,
fireplaces,stoves,etc.)thatcouldraisetheinternaltemperature
of the tank above 50°C.
installationandmaintenanceproceduresmaybefollowedinthe
most professional and expert manner possible. Important:
Disconnect the appliance from the electrical supply before
performinganymaintenanceorrepair.
PositioningtheHob
Important: this unit may be installed and used only in
permanently ventilated rooms in accordance with British
Standard Codes Of Practice:B.S. 6172 / B.S. 5440, Par. 2 and
B.S.6891 Current Editions.The following requirements must be
observed:
Installation of built-in hobs
a) Theroommustbefittedwithaventilationsystemwhichvents
smokeandgasesfromcombustiontotheoutside.Thismust
be done by means of a hood or electric ventilator that turns
onautomaticallyeachtimethehobisoperated.
The gas hobs are prepared with protection degree against
excessive heating of type X, the appliance can therefore be
installed next to cabinets, provided the height does not
exceed that of the hob. For a correct installation of the cooking
hob the following precautions must be followed:
a) The hob may be located in a kitchen, a kitchen/diner or
bed sitting room, but not in a bathroom or shower room.
b) The furniture standing next to the unit, that is higher than
the working boards, must be placed at least 110mm from
the edge of the board.
c) The cabinets should be positioned next to the hood at a
height of at least 420 mm (Fig. C).
HOOD
Min. 900mm.
In a chimney stack or branched flue.
(exclusively for cooking appliances)
Directly to the Outside
b) Theroommusthaveanairflowtoallowforpropercombustion.
3
Thismustbe2m ³/hperkWofinstalledpower.Theairflowcan
becreatedusinganenclosedventwithaninnercrosssection
ofatleast100cm²whichmustnotbeabletobeblocked. Ithe
appliancedoesnothaveaflamefailuredevice, theventmust
Fig. C
d) Should the hob be installed directly under a cupboard,
the letter should be at least 700mm (millimetres) from the
worktop, as shown in Fig. C.
e) The dimensions of the room for the furniture must be those
indicated in the figures in the last two pages of the cover.
Fixing hooks are provided which allow to place the hob
plate on work tops that measure from 20 to 40 mm in
thickness (see Fig. D). To obtain a good fixing of the hob
plate it is advisable to use all the hooks supplied.
3
haveaninternalcrosssectionof200cm ³(Fig.A). Alternatively
theroominwhichthehobissituatedcanbeventedindirectly
through ventilation ducts as specified above, as long as the
adjacentroomisnotasharedarea, abedroomorpresentany
riskoffire(Fig.B).
Detail A
Adjacent
Room
Room to be
Vented
Fig. D
min. 55 mm.
A
Examples of ventilation holes
for comburant air.
Enlarging the ventilation slot
between window and floor.
835 mm.
Fig.A
Fig.B
c) Intensiveandprolongeduseoftheappliancemaynecessitate
supplementalventilation, e.g. openingawindoworincreasing
thepoweroftheairintakesystem(ifpresent).
Fig. D
1 2
Installation
Gas connection for gas hob
The hob should be connected to the gas-supply by a corgi
registered installer. During installation of this product it is
essential to fit an approved gas tap to isolate the supply
from the appliance for the convenience of any subsequent
removal or servicing. Connection of the appliance to the gas
mains or liquid gas must be carried out according to the
prescribed regulation in force, and only after it is ascertained
that it is adaptable to the type of gas to be used. If not,
follow the instructions indicated in the paragraph headed
“Adaptation to different gas types”. In the case of connection
to liquid gas, by tank, use pressure regulators that conform
to the regulation in force.
Hook position for
H=30mm top
Hook position for
H=40mm top
Front
Important: For safety, for the correct regulation of gas use
and long life of the appliance, ensure that the gas pressure
conforms to the indications given in table 1 “Nozzle and burner
characteristics”.
Hook position for
Back
H=20mm top
Connection to non-flexible tube
(copper or steel)
N.B: Use the hook contained in the "accessoires set"
f) In the event the hob is not installed above a built-in oven,
a wood panel must be inserted as insulation. This panel
must be placed at least 20 mm from the bottom of the
hob itself.
Important: When installing the hob above a built-in oven,
the oven should be placed on two wooden strips; in the
case of a joining cabinet surface, remember to leave a space
of at least 45 x 560 mm at the back.
Connection to the gas source must be done in such a way
as to not create any stress points at any part of the
appliance.
The appliance is fitted with an adjustable, "L" shaped connector
and a gasket for the attachment to the gas supply. Should this
connector have to be turned, the gasket must be replaced
(supplied with the appliance).
The feeding connector of the gas to the appliance is threaded
1/2 gas male cylinder.
Connection to flexible steel tube
The gas feed connector to the appliance is a threaded, male
1/2" connector for round gas pipe. Only use pipes and sealing
gaskets that that conform to the standards currently in force.
The maximum length of the flexible pipes must not exceed
2000 mm. Once the connection has been made, ensure
that the flexible metal tube does not touch any moving parts
and is not crushed.
560 mm.
Check the Seal
When installing on a built-in oven without forced ventilation,
ensure that there are air inlets and outlets for ventilating the
interior of the cabinet adequately.
Once the hob has been installed, make sure all the
connections are properly sealed, using a soapy water
solution. Never use a flame.
1 3
Installation
Adapting the Hob for Different Types of Gas
Regulation of Air Supply to the Burner
To adapt the hob to a different type of gas than that for
which it was designed, (see the sticker under the hob or on
the packaging), the burner nozzles must be changed, as
follows:
The burners do not need any primary air regulator.
Minimum Regulation
Minimum regulation:
• Turn the gas valve to minimum.
• Remove the pan supports and slide the burners out of
•
Remove the knob and turn the regulator screw (positioned
either on the side of the top or inside the shaft - Figs. A
and B) clockwise until the flame becomes small but
regular.
the hob.
• Unscrew the nozzles using a 7mm socket wrench and
replace them with those for the new type of gas. (See
table 1, “Burner and Nozzle Specifications”).
N.B.: In the case of liquid gas, the regulation screw must be
fully screwed in (clockwise).
• Reassemble the parts following the instructions in reverse
order.
• On completing the operation, replace the old rating label
with the one showing the new type of gas; the sticker is
available from Hotpoint Service (see KEY CONTACTS,
back page).
If the gas pressure is different than that prescribed, a
pressure regulator must be installed at the source, in
compliance with national standards governing the use of
piped gas regulators.
• Make sure that, when the knob is turned rapidly high to
low, the flame does not go out.
• In the event of a malfunction on appliances with the
security device (thermocouple) when the gas supply is
set at minimum, increase the minimum supply levels using
the regulator screw in Fig. A - B.
Once the adjustment has been made, apply sealing wax,
or a suitable substitute, to the old seals on the by-pass.
1 4
Electrical Connection
Before connecting to the power supply, make sure that:
Electrical connection
• the limiter switch and the domestic system can
withstand the load from the appliance (see rating
plate).
• the supply system is efficiently earthed according to
standards and laws in force.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The hob is designed to work with alternating current, the
supply voltage and frequency indicated on the rating plate
(situated under the hob). Make sure that the local supply
voltage corresponds to the voltage indicated on the rating
plate.
• the socket or double-pole switch are easily accessible
when the appliance is installed.
Connecting the supply cable to the mains electricity
supply
Important: the wires in the mains lead are coloured in
accordance with the following code:
For models supplied without a plug, fit a standard plug
suitable for the load indicated on the rating plate, onto a
cable and connect to a suitable socket.
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
To connect direct to the mains supply, a double pole switch
with a contact separation of at least 3mm suitable for the
load and complying with current standards and regulations
must be fitted between the appliance and the mains supply
outlet.
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
Connect the Green & Yellow wire to terminal marked “E”
or
or coloured Green or Green & Yellow.
The green-yellow earth wire must not be interrupted by the
switch.
Connect the Brown wire to the terminal marked “L” or coloured
Red or Brown.
The supply cable must be positioned so that no part of it
reaches a temperature of 50°C above room temperature.
For installation above a built-under oven, the hob and the
oven must be connected separately to the electricity supply,
both for safetly reasons and for easy removal of the oven
for repair, maintenance etc.
Connect the Blue wire to the terminal marked “N” or coloured
Black or Blue.
FAILURE TO OBSERVE THE ACCIDENT-
PREVENTION REGULATIONS RELIEVES THE
MANUFACTURER OF ALL LIABILITY.
DO NOT use adapters as they could cause overheating or
burning.
Replacing the cable
Use a rubber cable of the type H05RR-F with a suitable
cross section 3 x 0.75 mm².
The yellow-green earth wire must be 2-3 cm longer than
the other wires.
1 5
Characteristic of the burners and nozzles
Table 1
Liquid gas
Natural gas
Burner
Diameter Thermal power
By-pass
1/100
Nozzle
1/100
Flow*
g/h
Nozzler Flow*
(mm)
kW (p.c.s.*)
1/100
l/h
(mm)
Nom. Red.
(1)
(mm)
86
***
**
(mm)
116
Rapid
(Large) (R)
100
100
75
3.00
2.60
1.65
0.7
0.7
0.4
41
41
30
39
39
28
218
214
286
248
157
Reduced
Rapid (RR)
80
64
189
120
186
118
110
96
Semi Rapid
(Medium) (S)
Auxiliary
(Small) (A)
55
130
-
1.00
3.25
1.50
0.4
1.3
0.7
30
60
41
28
57
39
50
91
60
73
71
71
133
88
95
Triple Crown (TC)
236
109
232
107
309
143
Semi-Fish Kettle
Burner (SP)
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
Supply pressures
*
**
At 15°C and 1013 mbar-dry gas
*** Butane
Naturale
P.C.S. = 49,47 MJ/kg
P.C.S. = 37,78 MJ/m3
Propane
P.C.S. = 50,37 MJ/kg
(1) for models with security device (ref. F).
1 6
Notes
1 7
After Sales Service
"No company is better positioned to offer an after sales service on a
Hotpoint appliance than us - the manufacturer"
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts
and labour guarantee for the first 12 months. In addition to this you also have the advantage of free
replacement parts for the first 5 years when fitted by a Hotpoint
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales
service options:
Repair Service and Information Help Desk
UK: 08709 066066
Republic of Ireland: 1850 302 200
Note: Our operators will require the Model number and the Serial number of your appliance
Available 364 days a year with a fast, effective and value for money service. We have the largest white
goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a parts
and labour guarantee for 12 months from the date of the repair.
If you require any information or have any questions about your appliance, our operators are on hand with
help and advice.
All this ensures that you will receive the best available after sales service possible.
Extended Warranties
UK: 08709 088 088
Republic of Ireland: 1850 502 200
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover
plans to give you total peace of mind.
l Repair Protection Plan
-
FREE service repairs for a single Hotpoint appliance during the period
of cover.
l Kitchen Cover
-
FREE service repairs for all your Hotpoint appliances less than 8
years old.
Genuine Parts and AccessoriesUK: 08709 077 077
Republic of Ireland: (01) 842 6836
A wide range of genuine parts and accessories are available from our hotline or through our web site.
Genuine parts and accessories, extended warranties and service repairs are all
available on our web-site at:
GB
18
Guarantee
"Satisfaction guaranteed or your money back"
We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service or
engineer to call. If the technical problem is not resolved under this guarantee, we will replace your
machine or, if you prefer, give you your money back.
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free
replacement parts for the first 5 years (except microwaves, selected integrated appliances and cooker
hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.
Guarantee terms and conditions
Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the
following provisions that your appliance:
l
l
Has been installed and used correctly in accordance with this instruction booklet.
Has been used solely for domestic purposes and is located on domestic premises (ie. not for
commercial or trade use).
l
l
Has been properly connected to a suitable electrical supply voltage as stated on the appliance
rating plate.
Has not been subject to misuse, accident, modified or repaired by anyone other than one of our
own service engineers.
For pre purchase information on any other Hotpoint product call: 08701 50 60 70
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to
use quality recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the plug and cut mains cable off flush with the appliance.
Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains
socket.
GB
19
Key Contacts
After Sales Service
Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in
both the appliances and services we offer.
Repair Service and Information Desk
UK: 08709 066 066
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Model number:
Serial number:
Extended Warranties
UK: 08709 088 088
(Open 8 to 8 Mon - Sun)
Republic of Ireland: 1850 502 200
Genuine Parts and Accessories
UK: 08709 077 077
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)
Republic of Ireland: (01) 842 6836
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB.
195.036.405.03
10/2005 Part no. FP163 - 01
|