PDP COLOUR TV
USER'S MANUAL
PDP4220EU
Part No: IES050723
OSD Language Settings
Using the OSD settings menu
OSD language
OSD settings
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item OSD settings.
CHANGE PASSWORD
3) Press the [CH+ or CH-] button to select OSD language,and press
the [VOL+]button to enter the OSD language
4) Press the [ VOL+] button to select the language what you want use.
OSD position
OSD timeout
OSD language
OSD lock
Transparency
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELEC-
TRIC SHOCK, DO NOT REMOVE
COVER(OR BACK).NO USER-
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance( servicing ) instructions in
the literature accompanying the set.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFEGUARD
FIRE AND SHOCK PRECAUTIONS
Adequate ventilation must be provided to prevent heat build up inside unit. Keep the inside of unit free
from foreign objects, such as hairpins, nails, paper, etc. Do not build the set into a bookcase or other
enclosures in which it would be poorly ventilated. Do not place it on carpet or a bed as low ventilation
boles could become obstructed.
Do not set liquids, including flower vases and vessels filled with chemicals or water etc., On top of the
unit as liquid could get inside the unit. If a hazardous object falls inside the TV set, unplug it immediately
and call a qualified technician for removal.
When placing or moving the TV set, take care to insure that the power cord is fitted into the allocated slot.
To avoid damage to the power cord, never allow heavy objects such as the TV set itself to be placed on
the power cord. Keep cord away from radiating appliances. Do not allow cord to become knotted or
tangled. Do not lengthen the cord. When removing the power plug from the socket, always hold onto the
plug, never pull by the cord.
This TV set shall be connected to a main socket outlet with a protective earthing contaction
The main plug and main switch should be remain readily operable after installation
No nacked flame sources, such as lighted candles, should be placed on the apparatus
Minimum distances around the apparatus for sufficient ventilation
The use of apparatus in moderate climates
WARNING
Do not remove the back cover of the TV set. Accidental contact with high voltage components could result
in electric shock. When internal adjustment is necessary, please contact your distributor.
If your set produces sound but no picture, or it emits smoke or produces a strange sound or smell, continue
operation is dangerous. Immediately turn off power and remove the power plug from the socket and
contact your distributor.
During vacation or other occasions when you will not be using the set for an extended period, remove the
power plug from the socket.
This appliance should not be operated by children or infirm persons without adequate supervision.
-1-
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
STAND IN STALLATION
Stand installation
STANDD INSTTALLATION
If the TVV is to bee ddesktop mmounted
1.Youu will Taake outt standd ffrom acccessorry box aand puutt asidee levell flat rroof , annd thenn supporrt grouupware
like ffig.1 uusingg ssix sccrrew A (MM5X122)) standd grouupware. Pleease eennsure sscrew tto be fiix closely.
2.You wwill taake outt TV set aand putt aside ssoft fllat roooff,and tthen takke off ttwo scrreew B on baack covver as ffig.2.
3.Fixxed sttaand usee four sscrew AA accorrding Fig.22 ffixingg TV sett and eennsuree sscrew tto be ffiix clossely.
SSTTAANNDD IINSTALLL SKETTCH MAP
Fig.1
Fig.2
- 2 -
Preparation for Using your new TV
Selecting a location for the TV
1)Place the TV on the floor or on a sturdy platform in a location where light does not directly hit the screen.
2)Place the TV far enough from the walls to allow proper ventilation. Inadequate ventilation may cause
overheating, which may damage the TV.
NOTE: Please contact local dealer for wall mounting.
Learning about your TV
You can operate yourTV by using the buttons on the front panel or theremote control. Theterminals on the
back panel provide all the connections you will need to connect otherequipment to your TV.
Front Controls
MENU
SOURCE
VOL
CH
- 3 -
Preparation for Using your new TV
28
21
13
18
22
11
12
14
15
16
17
19 20
24
25
26
27
AUDIO
3
AUDIO
2
AUDIO
1
PIP
AUDIO
OUT
PC
VIDEO OUT
VIDEO IN
ANT
75
AUDIO
IN
B
AUDIO OUT
L
R
AUDIO IN
L
Power
S- VID
EO
B
L
L
R
CVBS/YC
CVBS/RGB
Scart1 connector
Video input
S-video input
Remote Sensing Window
Power indicator
Menu button
CATV antenna input
Scart2 connector
YPBPR/YCBCR input
VGA input
Source
PIP headphone output
Volume up / cursor right
PC/ DVI audio input
S-VIDEO AUDIO INPUT
DVI input
Volume down / cursor left
Channel up / cursor up
RS232C DEBUG input
AC Power Socket
Spare port
YPBPR/YCBCR AUDIO input
AV audio input
Channel down / cursor down
Power button (standby)
28
audio output
(ON/OFF)
VIDEO OUTPUT
Power Switch
Note: The above figures are for reference only, please refer to the actual units to determine their appearance.
- 4 -
Preparation for Using your new TV
Connecting your TV
Caution: Do not plug the TV in until you have finished connecting all of your equipment.
Connecting to A/V equipments
To enjoy its multimedia features, you can connect your TV to A/V equipments such as VCR, DVD, STB, Satellite
receiver, Camcorder, Audio amplifier etc., and select signal sources using your remote control. Connect the
devices as shown below.
1
AUDIO
3
AUDIO
2
AUDIO
1
PIP
AUDIO
OUT
PC
VIDEO OUT
VIDEO IN
ANT IN
75
AUDIO
IN
AUDIO OUT
L
B
R
AUDIO IN
L
Power
S- VID
EO
B
L
L
R
CVBS/RGB
CVBS/YC
SCART2
SCART1
STB
PB
Y
CENTER
LEFT
S.L
S-VIDEO
VGA
ANT
1
RIGHT
S.R
SUBWOOFER
PR
CV
S/PDIF
VCD, DVD
B
R
Notes: Modes that YPBPR/YCBCR can display include:480P/60Hz,480I/60Hz,576P/50Hz,576I/50Hz
720P/50Hz,720P/60Hz,1080I/50Hz,1080I/60Hz
Connecting to a Computer
You can use your TV as a monitor/speakers for your computer by connecting through its 15pin standard RGB
interface and PC audio interface. Connect the devices as shown below.
- 5-
Preparation for Using your new TV
RGB line
PC/NB
AUDIO
3
AUDIO
2
AUDIO
1
PC
AUDIO
IN
AUDIO OUT
L
B
R
AUDIO IN
L
S- VID
EO
L
L
B
R
To speaker
To VGA
Audio line
Connecting to an antenna
To enjoy the terrestrial signal transmitted by your local TV station, you need an indoor or outdoor antenna
(not supplied). Perfect picture quality requires a good signal and generally means that an outdoor antenna
must be used. The exact type and location of the antenna will depend on your particular area. Consult your
local dealer or service personnel for best advice. If you are a subscriber of your local CATV net, the outdoor
or indoor antenna is not needed. Connect the equipments as the following figure.
Plug(not supplied)
COAXIAL CABLE (75W )
The signalcomesfrom:
An outdoor antenna
An indoor antenna
CATV net
TWIN-LEAD FEEDER(300W )
Adaptor (not supplied)
Loosen the screw
Insert the feeder in
Tighten the screw
ANTENNA SOCKET
ANT 75W
- 6-
Using the remote control
Preparing the remote control for use
Installing the remote control batteries
1. Open the battery cover on the back of the remote control.
2. Install two AAA size(1.5V) batteries. Match the + and - signs on the batteries to the signs on the battery
compartment.
3. Close the battery cover.
Note:
1.Dispose of your batteries in a designated disposal area. Do not throw batteries into fire.
2.Do not mix battery types or combine used batteries with new ones.
3.Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment.
4.If you do not intend to use the remote control for a long time, remove the batteries.
5.The effective range of remote control is suggested in the figure.
M6
15
30
30
6m
8m 6m
- 7-
Using the remote control
Learning about the remote control
Power:Power on/off
Channel number:
Direct channel selection
Teletextselect
Recall :
Return to previous channel
Display:Display current input
Text
P.Mode:Select picture mode
Teletext
CH+:Channel up
VOL-:Volume down
VOL+:Volume up
CH-:Channel down
Menu:Call up themain menu
S.Mode:Select sound mode
Mute:Mute the sound
S-VIDEO:Switch to S-VIDEOsource
:
Still:Snapshooting
Sub.Code
Zoom
Index
Zoom:Ajust zoom ration
Still
: Mono/Stereo operation
Size
Hold
Video:Switch to Videosource
Video
PC
Mix
PC:Switch to VGA/DVIsource
S-Video
Reveal
Cancel
Source:Switch input source
Source
YPBPR
Swap
SWAP:Exchange main sourceand PIP source
YPBPR:Switch to YPBPR source
PIP
Source
CH-
CH+
PIP CH+: PIP Channelup
PIP CH-: PIP Channeldown
PIP Source:Switch input PIPsource
- 8-
Using the TV features
Understanding the TV features
Multimedia - TV receiver, Video monitor and PC display, all in one.
Wider viewing angle, 16:9 display - 160 viewing angle at typical value
Digital display device - truthfully reproducing the images, without distortion or blurring, irrespective
of magnetic or geomagnetic effect.
200 channels storage
Sleep timer
Teletext with 252 pages memory
NICAM
Two SCART interface
Multi-language OSD
Basic Operations
Power ON/OFF
1) Connect the TV to power outlet and turn on the power switch, the power
indicator will be red and then turn blue.Several seconds later, TV picture
will display on the screen.
MENU
POWER
INDICATOR
SOURCE
2) Press the Power button on the front control or on the remote control to make
the TV on standby.Press the power switch to turn off power.
VOL
3) If you decide to shut off the TV for a long time, it is recommended
that you unplug the power from the outlet.
CH
POWER BUTTON
(STANDBY)
Signal source selection
Press [CH+/CH- ] button to selectTV main source input;press the [SOURCE] buttonto select TV ,YPBPR ,Video,
S-video,VGA,DVI, scart1,scart2 input;press the [VIDEO] button to selectVIDEO input; press the
[S-VIDEO] button to select S-VIDEO input;press the [ YPBPR button to select YPBPR input; press the [PC]button
to select VGA or DVI input;
press the [PIP SOURCE]button to select TV,YPBPR ,video,vga,dvi,scart1,scart2 input of pip
source input;press [PIP CH+/CH- ]button to select TVinput;
press the [SWAP] button to swap main source input and pip source input.
Select channels by [CH+/CH-]
Select channels by [CH+/CH-]
- 9-
Using the TV features
Select channels by [CH+/CH-]
You can also use[CH+ / CH-] to select channels. [CH+] indicates channel number increase; [CH-] indicates channel
number decrease.
Select channels by numbers
To select a channel : Press the channel numbers in series to select channel directly.
For example, to seclect channel 120, Press the button 1, and 1 will display on the top right corner of the screen,
then press the button 2, 12 will display, press the button zero, you can enjoy the program of channel 120.
NOTE:
1) When you changing the channel, the sound state graphics can be displayed below the channel number. There
are 3 sound states in this TV. If the sound is mono, the graphics is , If the sound is stereo, the graphics is
If the sound is NICAM dual I/II, the graphics is
.
Which indicate preset of picture system and sound system.
There are two symbol at right of thesound state graphics,
2) When you changing the channel, the sound of current channel will be firstly changed to stereo or NICAM dual I
according to the sound state of current channel. You can press the I/II button on the remote control to change
current sound type.
Adjust Volume
When menu is not displayed on the screen, press [VOL+ or VOL-] to adjust the volume.
Use [Recall] button
Power ON/OFF
Press the [ Recall ] button repeatedly to alternate between the present channel and the previous channel.
Display channel number
Press [Display] button to display the present channel number, but it will also disappear 3 seconds after your pressing.
Select picture modes
Normal
You can select the picture mode from among three preset modes and one user-set
mode. Press the [ P.mode ] button repeatedly to select the desired picture mode.
User
Soft
Bright
Select sound modes
You can select the sound mode from among three preset modes and one user-set
mode. Press the [ S.mode ] button repeatedly to select the desired sound mode.
Speech
Nomal
User
Use [Still] button
Music
Press the [ Still ] button to snapshot the present picture, and press again to return to normal watching.
Use [ Zoom ] button
Press the [ Zoom ] button to adjust the screen aspect ratio and zoom ratio
Mute function
Press [ Mute ] button repeatedly to switch between mute and unmute mode.
- 10-
Using the TV features
Using the TV settings menu
Program
Tv settings
1) Press the [MENU] button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item TV settings.
3) Press the [CH+ or CH-] button to select Program.
Program
4) Press the [VOL+ or VOL-] button to select the present channel.
Sound system
Auto search
Manual search
Fine tune
Sound system
You can set sound syetem.
Skip
1) Press the [MENU] button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item TV settings
3) Press the [CH+ or CH-] button to select sound system.and press
the [VOL+] button to enter sound system
Program edit
4) Press the [VOL+ ] button to switch among AUTO
I
D/K B/G L/L`
Tv settings
AUTO-Search
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item TV settings.
3) Press the [CH+ or CH-] button to select Auto search and press
the [ VOL+ ] button to enter Auto search .
Program
Sound system
Auto search
Manual search
Fine tune
4) Press the [ VOL+ ] button to switch among Normal and Auto +L/L`.
Normal
Notes:If you want to select L/L` and else sound system,
please select [auto search +L/L`] as right shown.
Auto +L/L`
Skip
Program edit
Manual search
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item TV settings.
3) Press the [CH+ or CH-] button to select Manual search.
4) Press the [ VOL+ or VOL-] button to start Manual searching.
Fine tune
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item TV settings.
3) Press the [CH+ or CH-] button to select Fine tune.
4) Press the [ VOL+ or VOL-] button to start Fine searching.
Skip
1) Press the [MENU] button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item TV settings
3) Press the [CH+ or CH-] button to select Skip.
4) Press the [VOL+] button to skip or unskip the present channel.
NOTE: The 'skipped' channels cannot be accessed by [CH+ or CH-] , but you can access them by digit (direct select)
button.
-11-
Using the TV features
Program edit
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item TV settings.
3) Press the [CH+ or CH-] button to select program edit.
4) Press the [ VOL+] button to start program edit.
5)Program edit can carry out program1 and program2 to be interchanged by the button [SWAP],or copy program1 to
program2 by the button [COPY].
Using the Picture menu
PROGRAM
Adjust picture settings
Picture parameters
1) Press the [MENU] button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item Picture
Parameters.
3) Press the [CH+ or CH-] button to select the item you want to adjust.
Brightness
Contrast
Saturation
4) Press the [VOL+ or VOL-] button to adjust the level.
5) The adjusted data is stored automatically in the user mode.
Hue
Colour temp
Sharpness
NOTE : The Colour temp is only to adjust in the PC mode.
.
Using the Audio settings menu
Adjust audio settings
Audio settings
1) Press the [MENU] button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item Audio settings.
3) Press the [CH+ or CH-] button to select the item you want to adjust.
4) Press the [VOL+ or VOL-] button to adjust the level.
5) The adjusted data is stored automatically in the user mode.
Bass
Treble
Balance
Sorround
Using the PIP menu
Picture in picture
1) Press the MENU button to enter the main menu ,press the
[VOL+ or VOL-] to select the Picture in picture.
2) Press the [CH+ or CH-] button to select the PIP size, and
press the [ VOL+] button to enter the PIP size, Press the
[CH+ or CH-] button to select the Off/Small/Medium/Large/PBP .
3) Press the [CH+ or CH-] button to select the PIP saturation, and
PIP position
PIPsize
PIPbrightness
PIP contrast
press the[ VOL+] button to enter the PIP saturation, Press the
[CH+ or CH-] button to select the pip saturation.
PIP saturation
Volume
4) Press the [CH+ or CH-] button to select the PIP position or PIP
brightness or PIP contrast, press the [VOL+ or VOL-] button to adjust the value.
Note: 1) When main picture is TV/ VIDEO/SCART/S-VIDEO. pip picture is HDTV/VGA.
2) When main picture is HDTV/VGA. pip picture is TV/ VIDEO/SCART.
-12 -
Using the TV features
Using the OSD settings menu
OSD position
OSD settings
1) Press the [MENU] button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item OSD
settings.
3) Press the [CH+ or CH-] button to select OSD position
4) Press the [VOL+ or VOL- ] button to
adjust the OSD POSITION
OSD position
OSD timeout
OSD language
OSD lock
OSD timeout
Transparency
1) Press the [MENU] button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item OSD
settings.
3) Press the [CH+ or CH-] button to select OSD timeout
4) Press the [VOL+ or VOL- or CH+ or CH-] button to
adjust the OSD TIMEOUT
OSD language
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item OSD settings.
CHANGE PASSWORD
3) Press the [CH+ or CH-] button to select OSD language,and press the [VOL+]]button
to enter the OSD language
4) Press the [ VOL+] button to select the language what you want use.
OSD lock
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item OSD settings.
CHANGE PASSWORD
3) Press the [CH+ or CH-] button to select OSD lock ,and press the [VOL+]button
to enter the OSD lock
4) Press the [ VOL+] button to select Yes, then OSD locked.
At that time you press MENU again,the screen will display as right shown.
Notes: If you want to unlock the OSD, please press [9] when the screen
display as right shown.
OSD locked!
Transparency
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item OSD settings
3) Press the [CH+ or CH-] button to select Transparency
4) Press the [ VOL+ or VOL-] button to adjust the ITEM
-13 -
Using the TV features
Using the General settings menu
Colour system
You can set colour syetem.
General settings
1) Press the [MENU] button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item
General settings
3) Press the [CH+ or CH-] button to select colour system and press
the [VOL+] button to enter colour system
4) Press the [VOL+ ] button to switch among Auto, Pal ,Secam.
Colour system
Noise reduce
Deinterlace
Factory reset
Sleep timer
Noise reduce
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item General settings
3) Press the [CH+ or CH-] button to select Noise reduce.
4) Press the [ VOL+ ] button to enter the Noise reduce.
5) Press the [ CH+ or CH-] button to select Low / Middle / High .
Deinterlace
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item General settings
3) Press the [CH+ or CH-] button to select Deinterlacer
4) Press the [ VOL+ ] button to enter the Deinterlacer
5) Press the [ CH+ or CH-] button to select the feature
Factory reset
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item General settings
3) Press the [CH+ or CH-] button to select Factory reset.
4) Press the [ VOL+-] button to select Yes or No .
Sleep timer
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item General settings
3) Press the [CH+ or CH-] button to select Sleep timer
4) Press the [ VOL+-] button to adjust the Sleep timer
-14-
Using the TV features
Using the PC menu
PC Parameters
1) Press the MENU button to enter the main menu.
2) Press the [VOL+ or VOL-] button to select the item
PC Parameters.
3) Press the [CH+ or CH-] button to select the item you
want to adjust.
Auto
LANGUAGE
Clock
ENGLISH
NOTE: 1)The menu is useful only on VGA/DVI and HDTV mode.
It is useless in others mode.
Phase
Position
I/p info
The button [AUTO] is used to adjust position of picture
automatic and it is effective only onVGA mode.
The button [POSITION] is used to adjust the position of
picture.
2)
The button [CLOCK] and [PHASE] can adjust quality of picture minutely,
and they are used less.
3) In HDTV mode ,Clock can not beselect.
4) In DVI mode,I/P info can beselect only.
Teletext Operations
Selecting teletext mode
Select the channel that is broadcasting the desired Teletext program.
Press [ TEXT ] button and alternate between Teletext mode and normal mode.
Note: All the operations below should be under the Teletext mode except TIME operation.
Page selection
You can directly input your desired page number by pressing [0-9] buttons.
You can sequentially read pages by pressing [CH+ or CH-] button.
Hold
Some Teletext information iscontained on more than one page, the pages automatically changing
after a given reading time.
Press [ S-Video ] button to stop the page changing.
Press [ S-Video ] button again to allow the page to change.
Reveal
Some Teletext pages containquiz or questions with hidden answers.
Press the [ Source ] button to see the answers.
Press the [ Source ] button again to hide the answers.
Cancel
When a page is selected in Teletext mode it may take some time before it becomes available.
Press the [ YPbPr ] button to switch to the TV mode.
When the required page is found, the page number will appear at the top of the TV picture,
press the [ YPbPr ] button to return to the selected Teletext page.
Note: You can not change TVprogram while in this mode.
-15-
Using the TV features
Teletext Operations
Sub code
Some Teletext pages contain sub page that require you to input the sub code.
Press [ Zoom ] button until ***|**** is displayed, and enter last four-digit sub code for the sub page you need.
Mix
You can mix Teletext with TV pictures, which means transparent teletext.
Press [ Swap ] to mix, and press [ Swap ] again to cancel the mixed effect.
Size (top/bottom/full)
Press the [ PC ] button to display the TOP HALF of the page.
Press again to display the BOTTOM HALF of the page.
Press again to return to a FULL PAGE display.
Note: Changing pages reverts to a FULL PAGE display.
Index
Teletext index page guides you quickly to your desired page.
Press [ Vedio ] button to enter index page.
Fast text
The RED, GREEN, YELLOW & CYAN buttons are used for quick access to colour coded pages
transmitted by FAST TEXT broadcast.
-16-
Appendix
The SCART interface
Also known as Peritel, this standard provides a cheap multi-signal connector
to domestic TV and other video equipment.
Arrangement 1 is the original and allows for composite video input/output,
RGB inputs and stereo audio input/output.
Arrangement 2 allows for composite video input/output,and stereo audio
input/output.
Cation:The output of video and audio are always from turner of R F.
Arrangement 3 allows for composite video input, S-Video inputs,and stereo
audio input/output.
TV can auto check aspect ratio in scart.
Scart Connector Pinout Details
SCART arrangement 1
Pin Signal
Signal level
0.5V rms
0.5V rms
0.5V rms
-
Impedance
<1kohm
>10kohm
<1kohm
-
1
2
3
4
5
6
7
Audio output B (right)
Audio input B (right)
Audio output A (left)
Ground (audio)
Ground (blue)
-
-
Audio input A (left)
Blue input
0.5V rms
0.7V
>10kohm
75ohms
-
High (5 12V) -AVmode
Mid(5-8V)-Wide-screen
8
Function select (AV control)
>10kohm
Low (0-2V)-TV mode
9
Ground (green)
-
-
-
-
-
10
11 Green input
12
0.7V
75ohms
-
-
-
13 Ground (red)
14 Ground (blanking)
15 Red input
-
-
-
-
0.7V
75ohms
High (1-3V)- RGB
16 RGB switching control
75ohms
Low (0
-0.4V)- Composite
17 Ground (video input & output)
-
-
-
18 Ground(RGB Switching
-
Control)
19 Video output (composite)
20 Video input (composite)
21 Common ground (shield)
1V including sync
75ohms
75ohms
-
1V including sync
-
-17 -
Appendix
SCART arrangement 2
Pin Signal
Signal level
Impedance
1
2
3
4
5
6
7
Audio output B (right)
Audio input B (right)
Audio output A(left)
Ground (audio)
Ground
0.5V rms
<1kohm
0.5V rms
>10kohm
0.5V rms
<1kohm
-
-
-
-
Audio input A(left)
-
0.5V rms
-
>10kohm
-
-
High(5 12V)
- AVmode
>10kohm
8
Function select (AV control)
Mid(5-8V)-Wide-screen
Low (0-2V) -TV mode
9
Ground
-
-
-
-
-
-
-
10
11 -
-
-
-
12
13 Ground
-
-
-
14 Ground (blanking)
-
75ohms
-
0.3V
15
16 -
-
-
-
-
17 Ground
-
18
19
20
-
Ground
Video output
Video input
75ohms
1V including sync
1V including sync
-
75ohms
-
21 Common ground (shield)
WARNING: Do NOT attempt to work on ANY equipment unless you KNOW what you are doing.
Notes: Y/C cannot be displayed inthe PIP source.
Cleaning and care
WARNING: Do not try to remove the cabinetback. Refer servicing toqualified service technicians.
To clean the TV screen:
1) Unplug theTV to avoid possible shock hazard.
2) Use a clean cellulose sponge or chamois clothdampened with a solution ofmild detergent and warm
water to clean theTV screen andtrim. Do not use too much wateras water spilled into the cabinet
can cause damage to theTV.
3) Wipe offany excess moisture with aclean dry cloth.
4) Polish the cabinet with a qualityfurniture polish to maintain thefinish and appearance of thecabinet.
Caution: Never use strong solvents such as thinner, benzene, or otherchemicals on or nearthe cabinet.
These chemicals can damage the finish ofthe cabinet.
-18 -
Appendix
Troubleshooting
Before calling a service technician, please check the following table for a possible cause of the problem and
some solutions.
Possible Solutions
Symptoms
Make sure the power cord is plugged in, then press [Power].
The remote control batteries may be dead. Replace the batteries.
TV will not turn on
Check if you have set the off timer.
No picture, no sound
No sound, picture OK
Poor sound, picture OK
Poor picture, sound OK
Check the antenna/cable connections.
Press [Display] to see if you have select the right signal source.
The sound may be muted. Press [ >] on the remote control or .
The station may have broadcast difficulties. Try another channel.
Check the speakers cable connections.
The station may have broadcast difficulties. Try another channel
Check the speakers cable connections.
Check the antenna connections.
The station may have broadcast difficulties. Try another channel.
Adjust the picture from the menu.
The channel may be skipped. See SKIP on page 11.
Unable to select a certain channel
Poor colour or no colour
The station may have broadcast difficulties. Try another channel.
Adjust the HUE and COLOUR in the menu.
There may be an obstruction between the remote control and the
remote control sensor.
The batteries may be installed with a wrong polarity.
The remote control batteries may be dead. Replace the batteries.
Check if youhave entered Teletext mode. Press[ Text ] toquit.
The remote control does not operate
Maybe TV signal isn't so good, you can try Fine tune to adjust.
See page 11
Abnormal TV picture
Customer important notice: When theTV can not be operationedin some special situation,please unplug the power and restart.
-19 -
Specifications
PDP4220EU
42 inch PDP
LCD panel
Multi- system(PAL,SECAM)
Television system
VHF-L: E2-S8
VHF-H: S9-S37
UHF: S38-E69
Channel coverage
640X480/60Hz,800X600/60Hz,1024X768/60Hz,1280X1024/60Hz
Analog RGB mode
Y PB/CB PR/CR mode
480I/60Hz,480P/60Hz,576P/50Hz,720P/50Hz,720P/60Hz,
1080I/50Hz,1080I/60Hz
852X480
Resolution
Contrast
10000:1
1500cd/m2
Brightness
Viewing angle
Power source
160o(H)/160o(V)
AC100V--240V, 50/60Hz
Power consumption
Audio output
280W
7W+7W
RF input:
1 CATV R
F
antenna input
VIDEO input:
1 AV input
1 s-video input
1 Y PB PR input
GRAPHIC input: 1Analog RGB 15pin(VGA) input
1 Digital RGB(DVI-D) input
Connection interface
AUDIO input:
1 AV audio
1PC/ DVI audio
1 S-video audio
1Y PB PR audio
AUDIO output: 1 audio output
1 PIP audio output
Video output
1 video output
SCART : SCART1 ( forCVBS, RGB andCANAL+ )
SCART2 ( for CVBS and Y/C)
OTHER:
1 RS232C ( for software updating )
Dimensions
1242mmX750mmX92mm
35kg
( LXWXH )
Weight
Supplied accessories
Remote control, AC Power cord, Batteries
Design and specifications are subject to change without notice.
-20-
Appendix
PDP Wall-mounting Bracket Installation Guide
READ CAREFULLY BEFORE INSTALLATION!
THE INSTALLATION GUIDE SHOULD BE RETAINED FOR FUTURE REFERENCE.
Caution:
1. Do NOT attempt to install the TV by yourself to avoid mistakes or hazard. Refer all
installation to qualified servicing personnel.
2. Do NOT install the TV on a wall aslope or a wall that makes the TV screen sloping
over 25o off plumb line. Otherwise, it may cause tumble or injury.
3. Refer all installation to qualified servicing personnel.
4. One must follow the instructions in this guide to correctly install the TV.
5. It requires more than one person to install the TV.
6. Before installation, examine whether the wall conforms to the specifications and
whether the supplied parts can be fixed on it. The wall for mounting should sustain
the weight of TV and speakers, e.g. cement wall or brick wall. Do NOT attempt to
install the TV on a flexible wall such as sand wall or plaster wall, unless the bolt are
fixed on an area with standard building rigidity which sustains the weight of the TV
and speakers. If the rigidity of the wall can not be measured, every mounting hole
should sustain a frontal force of over 100N and a shearing force of over 200N.
7. Use the specified electric drill and drill bit for drilling. The drilling holes should
conform to the specifications.
8. To avoid fire and shock, do NOT place radiator, heater or humidifier below the
installed TV.
9. The TV should be kept away from moisture, sensors and power line. The TV should
be kept away from impact and vibration.
10. Ensure that the power supply be disconnected before installation for fear of fire
and shock.
Wall-mounting Installation Steps:
1. Take out the brackets from the package, and check if there are serious defects
(e.g. infirm juncture).
2. Adjust the bracket to the desired angle. Use the bolts 2 to adjust the angle by
meeting holes of column beam 8 and holes of lever 5
3. Drill locating holes in the specified dimension in a vertical wall of concrete or brick.
The hole size should be 11mm. The hole depth should accommodate the
expanding tube of the bolt.
4. Fix the bolts into the drilled holes in step3, and then cover each bolt with a metal
washer. Meet the four mounting holes in the bracket with the four bolts in the wall,
cover each bolt with a metal washer, and then fasten with a screw nut. Check its
rigidity by pulling the bracket.
5. Fix the fixture disk 4 to the back cover of the TV using four bolt 3(M8X45).
6. Wall-mount the TV by putting the four fixture disks into the four mounting holes A.
7. If the customer is not satisfied with the mounting angle, take down the TV and
adjust the angle before re-mounting.
8. After wall-mounting the TV, use bolts 2 to fix the fixture disks for fear of accidental
slide.
-21 -
Appendix
-22-
|