MODELS G0747 & G0748
10" x 50" VERTICAL
MILLING MACHINE
w/POWER FEED
OWNER'S MANUAL
(For models manufactured since 8/12)
Model
Model
g0747
g0748
Copyright © MArCh, 2013 By grizzly industriAl, inC.
WARNING: NO PORTION OF THIS MANUAL MAy bE REPRODUCED IN ANy SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIzzLy INDUSTRIAL, INC.
#ts15453 printed in ChinA
Table of Contents
INTRODUCTION............................................... 3
SECTION 4: OPERATIONS ........................... 26
operation overview..................................... 26
table Movement .......................................... 27
graduated index rings.....................................27
table locks.......................................................27
X-Axis power Feed identification......................28
X-Axis power Feed operation ..........................29
head Movement........................................... 29
tilting head Forward/Backward........................30
rotating head left/right ..................................30
ram Movement............................................ 31
Moving ram Forward/Backward.......................31
rotating ram....................................................31
spindle speed.............................................. 32
determining spindle speed ..............................32
setting Model g0747 spindle speed ...............33
setting Model g0748 spindle speed ...............35
spindle downfeed........................................ 36
downfeed Controls ...........................................36
Coarse downfeed .............................................37
Fine downfeed..................................................37
Auto-downfeed .................................................38
spindle Brake............................................... 39
loading/unloading tooling .......................... 40
loading tooling ................................................40
unloading tooling.............................................40
Machine description ...................................... 3
Contact info.................................................... 3
Manual Accuracy ........................................... 3
Front View identification ................................ 4
Model g0747 headstock identification.......... 5
Model g0748 headstock identification.......... 6
g0747 Machine data sheet .......................... 7
g0748 Machine data sheet .......................... 9
SECTION 1: SAFETy..................................... 11
safety instructions for Machinery ................ 11
Additional safety for Milling Machines......... 13
SECTION 2: POWER SUPPLy...................... 14
Availability.........................................................14
Full-load Current rating ..................................14
Circuit requirements for 220V..........................14
grounding instructions......................................15
extension Cords................................................15
SECTION 3: SETUP ....................................... 16
unpacking.................................................... 16
needed for setup......................................... 16
inventory ...................................................... 17
Cleanup........................................................ 18
site Considerations...................................... 19
lifting & placing........................................... 20
leveling & Mounting .................................... 21
leveling.............................................................21
Bolting to Concrete Floors ................................21
Machine Mounts................................................21
Assembly ..................................................... 22
initial lubrication.......................................... 22
test run ...................................................... 23
Mill test run.....................................................23
power Feed test run.......................................24
spindle Break-in .......................................... 25
inspections & Adjustments .......................... 25
SECTION 5: ACCESSORIES......................... 41
SECTION 6: MAINTENANCE......................... 43
schedule...................................................... 43
ongoing ............................................................43
Before Beginning operations............................43
daily, After operations......................................43
Cleaning & protecting.................................. 43
lubrication ................................................... 44
Quill...................................................................44
table Ways (one-shot oiler) ...........................45
headstock gearing ...........................................45
ram Ways ........................................................46
head tilt & ram pinions ..................................46
table elevation leadscrew...............................46
power Feed gears............................................47
Machine storage.......................................... 48
SECTION 7: SERVICE ................................... 49
troubleshooting ........................................... 49
Adjusting gibs.............................................. 51
Adjusting leadscrew Backlash.................... 52
X-Axis leadscrew Backlash .............................52
Cross leadscrew Backlash ..............................53
tramming spindle........................................ 54
SECTION 9: PARTS....................................... 59
Main ............................................................. 59
X- & y-Axis leadscrews .............................. 61
downfeed system........................................ 62
g0747 headstock........................................ 65
g0748 headstock........................................ 67
one-shot oiler............................................. 70
Accessories.................................................. 71
g0747 Machine labels & Cosmetics .......... 72
g0748 Machine labels & Cosmetics .......... 73
SECTION 8: WIRING...................................... 56
Wiring safety instructions............................ 56
g0747 Wiring diagram ................................ 57
g0748 Wiring diagram ................................ 58
WARRANTy & RETURNS ............................. 77
INTRODUCTION
Machine Description
Manual Accuracy
We are proud to provide a high-quality owner’s
manual with your new machine!
these milling machines are designed to remove
material from a metal workpiece that is secured
to the work table or a mill vise. the cutting tool
is fixed to the rotating spindle and moved into the
workpiece by lowering the spindle or moving the
table. the table moves in three axes (X-, y-, and
z-axis) with a power feed assist for the X-axis.
We made every effort to be exact with the instruc-
tions, specifications, drawings, and photographs
contained inside. sometimes we make mistakes,
but our policy of continuous improvement also
means that sometimes the machine you receive
will be slightly different than what is shown in
the manual.
spindle downfeed options are rapid (coarse)
control or slow (fine) control with adjustable auto-
downfeed controls.
if you find this to be the case, and the difference
between the manual and machine leaves you
confused about a procedure, check our website
for an updated version. We post current manuals
and manual updates for free on our website at
Both models offer a wide range of spindle speeds
and three auto-downfeed rates.
the wide range of cutting tools and optional
equipment available, combined with the flexible
features of these milling machines, make possible
countless metalworking operations.
Alternatively, you can call our technical support
for help. Before calling, please write down the
Manufacture Date and Serial Number stamped
into the machine id label (see below). this infor-
mation helps us determine if updated documenta-
tion is available for your machine.
Contact Info
We stand behind our machines. If you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. This will help us help you faster.
Manufacture date
Grizzly Technical Support
1203 Lycoming Mall Circle
Muncy, PA 17756
serial number
Phone: (570) 546-9663
Email: [email protected]
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
-3-
Model G0747/G0748 (Mfg. Since 8/12)
Front View Identification
headstock
(see pages 5–6)
Motor
ram
X-Axis
Ball handle
slotted
Work table
X-Axis
Ball handle
power Feed
limit switch
X-Axis
power Feed
Knee
Crank
Mounting point
(1 of 4)
y-Axis
Ball handle
Knee
-4-
Model G0747/G0748 (Mfg. Since 8/12)
Model G0747 Headstock Identification
Belt tension
Adjustment lever
Motor
high/low
range lever
Motor lock
lever
spindle
Brake
Belt housing
safety Cover
spindle
switch
spindle speed
range selector
Auto-downfeed
rate selector
Manual/power
downfeed selector
Auto-downfeed
direction pin
Coarse
downfeed lever
Fine downfeed
handwheel
Quill lock
lever
Fine downfeed
Clutch lever
Adjustable
downfeed stop
dial indicator
rod
Quill & spindle
To reduce your risk of
serious injury, read this
entire manual bEFORE
using machine.
-5-
Model G0747/G0748 (Mfg. Since 8/12)
Model G0748 Headstock Identification
Motor
high range
Variable speed
indicator
low range
Variable speed
indicator
spindle
Brake
Variable speed
handwheel
spindle
switch
spindle speed
range selector
Auto-downfeed
rate selector
Manual/power
downfeed selector
Auto-downfeed
direction pin
Coarse
downfeed lever
Fine downfeed
handwheel
Quill lock
lever
Fine downfeed
Clutch lever
Adjustable
downfeed stop
dial indicator rod
Quill & spindle
-6-
Model G0747/G0748 (Mfg. Since 8/12)
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0747 VERTICAL MILL - 16 SPEED
Product Dimensions:
Weight........................................................................................................................................................... 2,249 lbs.
Width (side-to-side) x Depth (front-to-back) x Height............................................................... 54 x 66-1/2 x 84-3/4 in.
Footprint (Length x Width)............................................................................................................................ 40 x 24 in.
Space Required for Full Range of Movement (Width x Depth).............................................................. 95 x 56-1/2 in.
Shipping Dimensions:
Type.......................................................................................................................................................... Wood Crate
Content........................................................................................................................................................... Machine
Weight............................................................................................................................................................ 2492 lbs.
Length x Width x Height....................................................................................................................... 55 x 54 x 78 in.
Must Ship Upright................................................................................................................................................... Yes
Electrical:
Power Requirement................................................................................................................... 220V, 3-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 220V
Full-Load Current Rating....................................................................................................................................... 7.9A
Minimum Circuit Size.............................................................................................................................................. 15A
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length................................................................................................................................................. 6 ft.
Power Cord Gauge......................................................................................................................................... 14 AWG
Plug Included........................................................................................................................................................... No
Recommended Plug Type................................................................................................................................... 15-15
Switch Type........................................................................................................................... Forward/Reverse Switch
Recommended Phase Converter....................................................................................................................... G5845
Motors:
Main
Type........................................................................................................................................... AEVF Induction
Horsepower................................................................................................................................................ 3 HP
Phase.................................................................................................................................................... 3-Phase
Amps................................................................................................................................................. 7.8A / 7.9A
Speed..................................................................................................................................... 3450 / 1725 RPM
Power Transfer ............................................................................................................................... V-Belt Drive
Bearings..................................................................................................... Shielded & Permanently Lubricated
-7-
Model G0747/G0748 (Mfg. Since 8/12)
Main Specifications:
Operation Info
Spindle Travel.............................................................................................................................................. 5 in.
Max Distance Spindle to Column........................................................................................................ 24-3/8 in.
Max Distance Spindle to Table............................................................................................................ 16-7/8 in.
Longitudinal Table Travel (X-Axis)...................................................................................................... 29-7/8 in.
Cross Table Travel (Y-Axis)................................................................................................................ 15-3/4 in.
Vertical Table Travel (Z-Axis).................................................................................................................... 16 in.
Ram Travel................................................................................................................................................ 24 in.
Turret or Column Swivel (Left /Right)................................................................................................... 360 deg.
Head Tilt (Left/Right).............................................................................................................................. 90 deg.
Head Tilt (Front/Back)............................................................................................................................ 45 deg.
Drilling Capacity for Cast Iron................................................................................................................ 1-1/4 in.
Drilling Capacity for Steel............................................................................................................................ 1 in.
End Milling Capacity.................................................................................................................................... 1 in.
Face Milling Capacity................................................................................................................................... 3 in.
Table Info
Table Length.............................................................................................................................................. 50 in.
Table Width................................................................................................................................................ 10 in.
Table Thickness.................................................................................................................................. 3-5/16 in.
Number of T-Slots............................................................................................................................................ 3
T-Slot Size................................................................................................................................................ 5/8 in.
T-Slots Centers...................................................................................................................................... 2-1/2 in.
X/Y-Axis Travel per Handwheel Revolution.......................................................................................... 0.200 in.
Z-Axis Travel per Handwheel Revolution............................................................................................. 0.100 in.
Spindle Info
Spindle Taper............................................................................................................................................... R-8
Number of Vertical Spindle Speeds................................................................................................................ 16
Range of Vertical Spindle Speeds............................................................................................. 80 – 5440 RPM
Quill Diameter.......................................................................................................................................... 86 mm
Quill Feed Rates.................................................................................................... 0.0015, 0.003, 0.006 in./rev.
Drawbar Thread Size............................................................................................................................. 7/16-20
Drawbar Length................................................................................................................................... 23-1/2 in.
Spindle Bearings....................................................................................................... Angular Contact Bearings
Construction
Spindle Housing/Quill....................................................................... Chrome-Plated & Precision-Ground Steel
Table..................................................................................................... Precision-Ground Meehanite Cast Iron
Head................................................................................................................................................... Aluminum
Column/Base...................................................................................................................... Meehanite Cast Iron
Base..................................................................................................................................................... Cast Iron
Paint....................................................................................................................................................... Enamel
Other Specifications:
Country Of Origin ............................................................................................................................................... China
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time .............................................................................................................. 1 Hour
Serial Number Location ............................................................................................................... ID Label on Column
ISO 9001 Factory .................................................................................................................................................. Yes
CSA Certified .......................................................................................................................................................... No
-8-
Model G0747/G0748 (Mfg. Since 8/12)
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0748 VERTICAL MILL - VARIABLE SPEED
Product Dimensions:
Weight........................................................................................................................................................... 2,315 lbs.
Width (side-to-side) x Depth (front-to-back) x Height............................................................... 54 x 66-1/2 x 84-3/4 in.
Footprint (Length x Width)............................................................................................................................ 40 x 24 in.
Space Required for Full Range of Movement (Width x Depth).............................................................. 95 x 56-1/2 in.
Shipping Dimensions:
Type.......................................................................................................................................................... Wood Crate
Content........................................................................................................................................................... Machine
Weight............................................................................................................................................................ 2558 lbs.
Length x Width x Height....................................................................................................................... 54 x 55 x 78 in.
Must Ship Upright................................................................................................................................................... Yes
Electrical:
Power Requirement................................................................................................................... 220V, 3-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 220V
Full-Load Current Rating....................................................................................................................................... 6.6A
Minimum Circuit Size.............................................................................................................................................. 15A
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length................................................................................................................................................. 6 ft.
Power Cord Gauge......................................................................................................................................... 14 AWG
Plug Included........................................................................................................................................................... No
Recommended Plug Type................................................................................................................................... 15-15
Switch Type........................................................................................................................... Forward/Reverse Switch
Recommended Phase Converter....................................................................................................................... G5845
Motors:
Main
Type........................................................................................................................................... AEVF Induction
Horsepower................................................................................................................................................ 3 HP
Phase.................................................................................................................................................... 3-Phase
Amps........................................................................................................................................................... 6.6A
Speed................................................................................................................................................ 1725 RPM
Power Transfer ............................................................................................................................... V-Belt Drive
Bearings..................................................................................................... Shielded & Permanently Lubricated
-9-
Model G0747/G0748 (Mfg. Since 8/12)
Main Specifications:
Operation Info
Spindle Travel.............................................................................................................................................. 5 in.
Max Distance Spindle to Column........................................................................................................ 24-3/8 in.
Max Distance Spindle to Table............................................................................................................ 16-7/8 in.
Longitudinal Table Travel (X-Axis)...................................................................................................... 29-7/8 in.
Cross Table Travel (Y-Axis)................................................................................................................ 15-3/4 in.
Vertical Table Travel (Z-Axis).................................................................................................................... 16 in.
Ram Travel................................................................................................................................................ 24 in.
Turret or Column Swivel (Left /Right)................................................................................................... 360 deg.
Head Tilt (Left/Right).............................................................................................................................. 90 deg.
Head Tilt (Front/Back)............................................................................................................................ 45 deg.
Drilling Capacity for Cast Iron................................................................................................................ 1-1/4 in.
Drilling Capacity for Steel............................................................................................................................ 1 in.
End Milling Capacity.................................................................................................................................... 1 in.
Face Milling Capacity................................................................................................................................... 3 in.
Table Info
Table Length.............................................................................................................................................. 50 in.
Table Width................................................................................................................................................ 10 in.
Table Thickness.................................................................................................................................. 3-5/16 in.
Number of T-Slots............................................................................................................................................ 3
T-Slot Size................................................................................................................................................ 5/8 in.
T-Slots Centers...................................................................................................................................... 2-1/2 in.
X/Y-Axis Travel per Handwheel Revolution.......................................................................................... 0.200 in.
Z-Axis Travel per Handwheel Revolution............................................................................................. 0.100 in.
Spindle Info
Spindle Taper............................................................................................................................................... R-8
Number of Vertical Spindle Speeds...................................................................................................... Variable
Range of Vertical Spindle Speeds............................................................................................. 60 – 4200 RPM
Quill Diameter.......................................................................................................................................... 86 mm
Quill Feed Rates.................................................................................................... 0.0015, 0.003, 0.008 in./rev.
Drawbar Thread Size............................................................................................................................. 7/16-20
Drawbar Length................................................................................................................................... 23-1/2 in.
Spindle Bearings....................................................................................................... Angular Contact Bearings
Construction
Spindle Housing/Quill....................................................................... Chrome-Plated & Precision-Ground Steel
Table..................................................................................................... Precision-Ground Meehanite Cast Iron
Head................................................................................................................................................... Aluminum
Column/Base...................................................................................................................... Meehanite Cast Iron
Base..................................................................................................................................................... Cast Iron
Paint....................................................................................................................................................... Enamel
Other Specifications:
Country Of Origin ............................................................................................................................................... China
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time .............................................................................................................. 1 Hour
Serial Number Location ............................................................................................................... ID Label on Column
ISO 9001 Factory .................................................................................................................................................. Yes
CSA Certified .......................................................................................................................................................... No
-10-
Model G0747/G0748 (Mfg. Since 8/12)
SECTION 1: SAFETy
For your Own Safety, Read Instruction
Manual before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAy result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
OWNER’S MANUAL. read and understand this ELECTRICAL EQUIPMENT INJURy RISKS. you
owner’s manual BeFore using machine.
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. to reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
TRAINED OPERATORS ONLy. untrained oper-
ators have a higher risk of being hurt or killed.
only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!
DISCONNECT POWER FIRST. Always discon-
nect machine from power supply BeFore making
adjustments, changing tooling, or servicing machine.
this prevents an injury risk from unintended startup
or contact with live electrical components.
DANGEROUS ENVIRONMENTS. do not use
machinery in areas that are wet, cluttered, or have
poor lighting. operating machinery in these areas
greatly increases the risk of accidents and injury.
EyE PROTECTION. Always wear Ansi-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. everyday
eyeglasses are not approved safety glasses.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. never operate under the influence of drugs or
alcohol, when tired, or when distracted.
-11-
Model G0747/G0748 (Mfg. Since 8/12)
WEARING PROPER APPAREL. do not wear FORCING MACHINERy. do not force machine.
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips, which could cause loss of work-
piece control.
it will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
HAzARDOUS DUST. dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a niosh-approved respirator to
reduce your risk.
STAbLE MACHINE. unexpected movement dur-
ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for rec-
ommended accessories. using improper acces-
sories will increase the risk of serious injury.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observing loud
machinery. extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
UNATTENDED OPERATION. to reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. never leave machine running
while unattended.
REMOVE ADJUSTING TOOLS. tools left on
machinery can become dangerous projectiles
upon startup. never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
USE CORRECT TOOL FOR THE JOb. only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. never make unapproved modifica-
tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
CHECK DAMAGED PARTS. regularly inspect
machine for any condition that may affect safe
operation. immediately repair or replace damaged
or mis-adjusted parts before operating machine.
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
MAINTAIN POWER CORDS. When disconnect-
ing cord-connected machines from power, grab
and pull the plug—not the cord. pulling the cord
may damage the wires inside. do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
CHILDREN & bySTANDERS. Keep children and
bystanders at a safe distance from the work area.
stop using machine if they become a distraction.
EXPERIENCING DIFFICULTIES. if at any time
you experience difficulties performing the intend-
ed operation, stop using the machine! Contact our
technical support at (570) 546-9663.
GUARDS & COVERS. guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly.
-12-
Model G0747/G0748 (Mfg. Since 8/12)
Additional Safety for Milling Machines
UNDERSTANDING CONTROLS: the mill is a STOPPING SPINDLE: to reduce the risk of
complex machine that presents severe cutting or hand injuries or entanglement hazards, do not
amputation hazards if used incorrectly. Make sure attempt to stop the spindle with your hand or a
you understand the use and operation of all con- tool. Allow the spindle to stop on its own or use
trols before you begin milling.
the spindle brake.
SAFETy ACCESSORIES: Flying chips or debris CHIP CLEANUP: Chips from the operation are
from the cutting operation can cause eye injury sharp and hot, which can cause burns or cuts.
or blindness. Always use safety glasses or a face using compressed air to clear chips could cause
shield when milling.
them to fly into your eyes, and may drive them
deep into the working parts of the machine. use
WORK HOLDING: Milling a workpiece that is not a brush or vacuum to clear away chips and debris
properly secured to the table or in a vise could from machine or workpiece and neVer clear
cause the workpiece to fly into the operator with chips while spindle is turning.
deadly force! Before starting the machine, be
certain the workpiece has been properly clamped MACHINE CARE & MAINTENANCE: operating
to the table. neVer hold the workpiece by hand the mill with excessively worn or damaged machine
during operation.
parts increases risk of machine or workpiece
breakage which could eject hazardous debris at
SPINDLE SPEED: to avoid tool or workpiece the operator. operating a mill in poor condition will
breakage that could send flying debris at the also reduce the quality of the results. to reduce
operator and bystanders, use the correct spindle this risk, maintain the mill in proper working con-
speed for the operation. Allow the spindle to gain dition by AlWAys promptly performing routine
full speed before beginning the cut.
inspections and maintenance.
SPINDLE DIRECTION CHANGE: Changing CUTTING TOOL USAGE: Cutting tools have
spindle rotation direction while it is spinning very sharp leading edges—handle them with
could lead to impact injury from broken tool or care! using cutting tools that are in good condi-
workpiece debris, and workpiece or machine tion helps to ensure quality milling results and
damage. AlWAys make sure the spindle is at a reduces risk of personal injury from broken tool
complete stop before changing spindle direction.
debris. inspect cutting tools for sharpness, chips,
or cracks before each use, and AlWAys make
sure cutting tools are firmly held in place before
starting the machine.
Like all machinery there is potential danger
when operating this machine. Accidents
are frequently caused by lack of familiarity
or failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre-
cautions are overlooked or ignored, seri-
ous personal injury may occur.
No list of safety guidelines can be com-
plete. Every shop environment is different.
Always consider safety first, as it applies
to your individual working conditions. Use
this and other machinery with caution and
respect. Failure to do so could result in
serious personal injury, damage to equip-
ment, or poor work results.
-13-
Model G0747/G0748 (Mfg. Since 8/12)
SECTION 2: POWER SUPPLy
Availability
Circuit Requirements for 220V
This machine is prewired to operate on a 220V
power supply circuit that has a verified ground and
meets the following requirements:
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrican or
qualified service personnel in accordance with all
applicable codes and standards.
Nominal Voltage .............................. 220V/240V
Cycle..........................................................60 Hz
Phase.................................................... 3-Phase
Power Supply Circuit ......................... 15 Amps
Plug/Receptacle ............................NEMA 15-15
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power
supply.
Full-Load Current Rating
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
Note: The circuit requirements listed in this man-
ual apply to a dedicated circuit—where only one
machine will be running at a time. If this machine
will be connected to a shared circuit where mul-
tiple machines will be running at the same time,
consult a qualified electrician to ensure that the
circuit is properly sized for safe operation.
G0747 Full-Load Current Rating ....... 7.9 Amps
G0748 Full-Load Current Rating.......6.6 Amps
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the requirements in the following section.
-14-
Model G0747/G0748 (Mfg. Since 8/12)
Grounding Instructions
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
the power cord and plug specified under “Circuit
requirements for 220V” on the previous page
has an equipment-grounding wire and a ground-
ing prong. the plug must only be inserted into
a matching receptacle (outlet) that is properly
installed and grounded in accordance with all
local codes and ordinances (see figure below).
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec-
essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service per-
sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon-
nect it from power, and immediately replace it with
a new one.
GROUNDED
15-15 RECEPTACLE
15-15 PLUG
Current
Carrying
Prongs
Grounding Prong
Extension Cords
We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
Figure 1. typical 15-15 plug and receptacle.
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
Extension cords cause voltage drop, which may
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
contain a ground wire, match the required plug
and receptacle, and meet the following require-
ments:
Minimum Gauge Size...........................14 AWG
Maximum Length (Shorter is better).......50 ft.
No adapter should be used with the
required plug. If the plug does not fit the
available receptacle, or the machine must
be reconnected for use on a different type
of circuit, the reconnection must be made
by a qualified electrician and comply with all
local codes and ordinances.
-15-
Model G0747/G0748 (Mfg. Since 8/12)
SECTION 3: SETUP
Unpacking
Needed for Setup
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover any damage, please call us immediately
at (570) 546-9663 for advice.
the following are needed to complete the setup
process, but are not included with your machine.
For Lifting (Page 20)
•
A forklift or other power lifting device rated for
25% more than the weight of the machine.
two lifting straps and chain with a safety
hook, each rated for 25% more than the
weight of the machine.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
•
•
At least two other persons to help with the
operation.
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
For Power Connection
•
We recommend a qualified electrician to
ensure a safe and code-compliant connec-
tion to the power source. (refer to Page 14
for details.)
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
For Assembly
•
•
•
•
•
Cotton disposable rags
Cleaner/degreaser (see Page 18)
safety glasses for each person
hex Wrench 4mm
open-end Wrench 14mm
-16-
Model G0747/G0748 (Mfg. Since 8/12)
Inventory
A
B
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
C
e
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
d
F
h
g
i
Small Item Inventory: (Figure 2)
Qty
J
A. Front Way Cover..........................................1
b. rear Way Cover..........................................1
K
7
C. drawbar ⁄16"-20 x 231⁄2"...............................1
l
n
D. Ball handles ................................................3
E. Fine downfeed handwheel .........................1
F. Ball handle handles....................................3
G. toolbox........................................................1
H. Bottle for oil ................................................1
I. Belt housing safety Covers (g0747 only) .. 2
J. Knee Crank .................................................1
K. Coarse downfeed lever..............................1
L. Closed-end Wrench 17 x 19mm..................1
M. phillips screwdriver #2................................1
N. slotted screwdriver #2 ................................1
M
Figure 2. small item inventory.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
-17-
Model G0747/G0748 (Mfg. Since 8/12)
Cleanup
Gasoline or products
with low flash points can
explode or cause fire if
used to clean machin-
ery. Avoid cleaning with
these products.
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
Many cleaning solvents
are toxic if concentrat-
ed amounts are inhaled.
Only work in a well-venti-
lated area.
There are many ways to remove this rust preven-
tative, but the following steps work well in a wide
variety of situations. Always follow the manufac-
turer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
NOTICE
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces. Test all cleaners
in an inconspicuous area before using to
make sure they will not damage paint.
Before cleaning, gather the following:
•
•
•
•
Disposable Rags
Cleaner/degreaser (WD•40 works well)
Safety glasses & disposable gloves
Plastic paint scraper (optional)
T23692—Orange Power Degreaser
A great product for removing the waxy shipping
Basic steps for removing rust preventative:
grease from your machine during clean up.
1. Put on safety glasses.
2. Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3. Wipe off the surfaces. If your cleaner/degreas-
er is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
4. Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
Figure 3. t23692 orange power degreaser.
-18-
Model G0747/G0748 (Mfg. Since 8/12)
Site Considerations
Weight Load
Physical Environment
refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest work-
piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
the physical environment where the machine is
operated is important for safe operation and lon-
gevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemi-
cals, airborne abrasives, or extreme conditions.
extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20–95% (non-condensing); or the
environment is subject to vibration, shocks, or
bumps.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main-
tenance and service described in this manual.
See below for required space allocation.
Electrical Installation
place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals,
or other hazards. Make sure to leave access to
a means of disconnecting the power source or
engaging a lockout/tagout device, if required.
Lighting
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
lighting around the machine must be adequate
enough that operations can be performed safely.
shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
Wall
30"
Minimum
Clearance
30"
Minimum
Clearance
95"
24"
40"
561⁄2
"
Figure 4. Minimum working clearances.
Model G0747/G0748 (Mfg. Since 8/12)
-19-
Note: After re-positioning the ram and head-
stock, make sure they are locked in place to
prevent unexpected movement during lifting.
Lifting & Placing
Make sure the four turret lock bolts (two on
either side of the ram, see Figure 6) are
torqued to 47 ft/lbs. to keep the ram from
unexpectedly moving from the force of the
lifting straps.
HEAVy LIFT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a fork lift (or other
lifting equipment) rated for
weight of this machine.
turret locking Bolts
(2 of 4)
power lifting equipment (refer to Page 16) and
at least two other people are required to lift and
place the mill.
To lift and move the mill:
1. remove the crate from the shipping pallet,
then move the mill, while it is still on the pal-
let, to the installation location.
Figure 6. locations of turret locking bolts.
3. place the lifting straps under the ram and
connect them to the safety hook, as illus-
trated in Figure 5.
2. rotate the ram 180° so the headstock is fac-
ing backwards (see Figure 5), then rotate the
head upright.
Note: Place protective material between the
straps and the mill to protect the ram and
ways, and to keep from cutting the lifting
straps.
refer to Head Movement on Page 29 and
Ram Movement on Page 31 for detailed
instructions to help with this step.
4. unbolt the mill from the shipping pallet.
5. With other people steadying the load to keep
it from swaying, lift the mill a couple of inches.
—if the mill tips to one side, lower it to the
ground and adjust the ram or table to bal-
ance the load. Make sure to re-tighten the
lock levers and bolts before lifting the mill
again.
—if the mill lifts evenly, remove the shipping
pallet and lower the mill.
Figure 5. illustrated example of using lifting to
move the mill.
-20-
Model G0747/G0748 (Mfg. Since 8/12)
bolting to Concrete Floors
Leveling & Mounting
Anchor studs and lag shield anchors with lag
screw (Figure 8) are two popular methods for
anchoring an object to a concrete floor. We sug-
gest you research the many options and methods
for mounting your machine and choose the best
that fits your specific application
generally, you can either bolt your machine to the
floor or mount it on machine mounts. Although
not required, we recommend that you secure the
machine to the floor and level it while doing so.
Because this is an optional step and floor materi-
als may vary, hardware for securing the machine
to the floor is not included.
Anchor stud
Unless otherwise specified by your local
codes, this machine MUST be secured to
the floor if it is permanently connected
(hardwired) to the power supply.
lag shield
Anchor
Leveling
lag screw
leveling machinery helps precision components,
such as dovetail ways, remain straight and flat
during the lifespan of the machine. Components
on an unleveled machine may slowly twist due to
the dynamic loads placed on the machine during
operation.
Figure 8. typical fasteners for mounting to
concrete floors.
Machine Mounts
For best results, use a precision level that is at
least 12" long and sensitive enough to show a
distinct movement when a 0.003" shim (approxi-
mately the thickness of one sheet of standard
newspaper) is placed under one end of the level.
Machine mounts (see Figure 9 for an example)
provide the advantage of fast leveling and vibra-
tion reduction. the large size of the foot pads
distributes the weight of the machine to reduce
strain on the floor.
see Figure 7 for an example of a high precision
level available from grizzly.
Figure 9. Machine mount example.
Figure 7. example of a precision level
(Model h2683 shown).
-21-
Model G0747/G0748 (Mfg. Since 8/12)
4. using the five cap screws pre-threaded into
the holes, install the front way cover as
shown in Figure 12.
Assembly
Assembly of the small components of the mill
consists of attaching the ball handles, knee crank,
and the way covers.
To assemble the mill:
Cap screws
1. remove the hex nuts from the X- and
y-axis leadscrews, then slide the ball handles
(Figure 10) onto the leadscrews and secure
them with the hex nuts.
Note: Tighten the hex nuts just until they are
snug. Overtightening could increase the wear
of the moving parts.
Figure 12. Front way cover installed.
5. using the four cap screws pre-threaded into
the holes, install the rear way cover as shown
in Figure 13.
Ball handle
handle
Ball handle
Cap
screws
Figure 10. Ball handle assemblies.
2. thread the handles into the small end of the
ball handles and tighten them.
Figure 13. rear way cover installed.
3. slide the knee crank onto the shaft so that
the teeth of the crank and shaft engage, as
shown in Figure 11.
Initial Lubrication
the machine was fully lubricated at the factory,
but we strongly recommend that before perform-
ing the Test Run you inspect all lubrication
points yourself and provide additional lubrication
if necessary. refer to the Lubrication section on
Page 44 for specific details.
Knee Crank
teeth engaged
Figure 11. Knee crank teeth engaged.
-22-
Model G0747/G0748 (Mfg. Since 8/12)
7. use the spindle switch to turn the mill ON.
Test Run
For Model G0747: turn the spindle switch to
the FLOW (forward low) position, as shown in
Figure 14.
After all preparation steps have been completed,
the machine and its safety features must be
tested to ensure correct operation. if you discover
a problem with the operation of the machine or its
safety components, do not operate it further until
you have resolved the problem.
if you discover a problem with the operation of the
machine or its safety components, do not oper-
ate it further until you have resolved the problem.
refer to the Troubleshooting section on Page
49 for solutions to common problems that may
occur with all mills. if you need additional help,
contact our tech support at (570) 546-9663.
Figure 14. Model g0747 spindle switch.
Mill Test Run
1. read and follow the safety instructions at the
beginning of the manual, take required safety
precautions, and make sure the machine is
set up and adjusted properly
For Model G0748: turn the spindle switch
to the FOR (forward) position, as shown in
Figure 15.
2. Clear away all tools and objects used during
assembly and preparation.
3. Make sure that the mill is properly lubricated
(refer to the Lubrication section on Page 44
for specific details).
4. set the spindle speed to the low range (refer
to Page 33 or 35 for detailed instructions).
5. Move the downfeed selector to the manual
(forward) position so that the spindle does
not downfeed during this test (refer to the
Downfeed Operations section on Page 36
for detailed instructions).
Figure 15. Model g0748 spindle switch.
8. listen for abnormal noises and watch for
unexpected actions from the mill. the
machine should run smoothly and without
excessive vibration or rubbing noises.
6. Connect the mill to the power source speci-
fied in the POWER SUPPLy section on
Page 14.
—strange or unusual noises or actions must
be investigated immediately. turn the
machine OFF and disconnect it from the
power source before investigating or cor-
recting potential problems.
-23-
Model G0747/G0748 (Mfg. Since 8/12)
5. Make sure the power feed direction knob is in
the neutral (middle) position, turn the speed
dial counterclockwise to the lowest setting,
then press the on button.
Power Feed Test Run
the mill comes with a power feed unit for X-axis
table travel. proper operation of the limit switch
attached to the front middle of the table is criti-
cal for the safe use of this power feed unit. if the
power feed does not operate as expected during
the following steps, disconnect it from power and
contact our tech support at (570) 546-9663 for
assistance.
6. turn the direction knob to the left, slowly
turn the speed dial clockwise to increase the
speed, then confirm that the table is moving
to the left.
7. Watch for the table limit stop to hit the limit
switch and turn the power feed OFF, stopping
the table movement.
To test the power feed:
1. Make sure all tools, cables, and other items
are well clear of table movement as you fol-
low these steps.
8. turn the direction knob through the neutral
(middle) position and all the way to the right.
the table should begin moving to the right.
2. refer to the X-Axis Power Feed section,
beginning on Page 28, to understand how
the power feed, table locks, and limit switch
function.
9. Confirm that the table stops moving when
the limit stop presses against the limit switch
plunger.
3. loosen the table locks on the front of the
10. Move the direction knob to the neutral (mid-
dle) position, turn the speed dial to the lowest
setting, and press the oFF button.
table.
4. plug the power feed power cord into a
grounded 110V power outlet.
Congratulations! the Test Run of the mill is
complete. Continue to the next page to per-
form the Spindle break-In and Adjustments &
Inspections procedures.
-24-
Model G0747/G0748 (Mfg. Since 8/12)
Spindle break-In
Since the mill head has been moved around
for shipping purposes, you will need to tram
the spindle with the table to ensure a 90°
alignment. Refer to the Tramming Spindle
section on Page 54 for detailed instructions.
Complete the spindle bearing break-in pro-
cedure to prevent rapid wear and tear of
spindle components once the mill is placed
into operation.
Inspections &
Adjustments
the bearings and gears used in the mill are man-
ufactured to very close tolerances. Before opera-
tional stress is placed on these and other moving
parts in the mill, complete this break-in procedure
to conform these components to one another and
ensure trouble-free performance from the mill.
the following list of adjustments were performed
at the factory before the machine was shipped:
•
•
gib Adjustments.............................. Page 51
leadscrew Backlash
To perform the spindle break-in procedure:
Adjustments..................................... Page 52
1. successfully perform all the steps in the Test
Run section beginning on Page 23.
Be aware that machine components can shift
during the shipping process. pay careful atten-
tion to these adjustments during operation of the
machine. if you find that the adjustments are not
set according to the procedures in this manual or
your personal preferences, re-adjust them.
2. Make sure the spindle is at a complete stop.
3. set the spindle speed to the low range (refer
to Page 33 or 35 for detailed instructions).
4. start the spindle rotation at a medium speed
and let the mill run for 20 minutes.
5. stop the spindle rotation and allow the spin-
dle to come to a complete stop by itself.
6. set the spindle speed to the high range, then
start the spindle rotation at a medium speed
and let the mill run for another 20 minutes.
7. stop the spindle rotation, and turn the mill
OFF.
the spindle break-in is now complete!
-25-
Model G0747/G0748 (Mfg. Since 8/12)
SECTION 4: OPERATIONS
To complete a typical operation, the operator
does the following:
Operation Overview
1. examines the workpiece to make sure it is
The purpose of this overview is to provide the nov-
ice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.
suitable for milling.
2. Firmly clamps the workpiece to the table or a
mill vise.
3. installs the correct cutting tool for the opera-
Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual and seek additional training from expe-
rienced machine operators, and do additional
research outside of this manual by reading "how-
to" books, trade magazines, or websites.
tion.
4. uses the manual downfeed and table con-
trols to correctly position the cutting tool and
workpiece for the operation. if the X-axis
power feed will be used during the operation,
the operator confirms the speed and length of
table movement required.
5. Configures the mill for the correct spindle
speed of the operation.
To reduce your risk of
serious injury, read this
entire manual bEFORE
using machine.
6. puts on personal protective gear, and makes
sure the workpiece and table are clear of all
tools, cords, and other items.
7. starts the spindle rotation and performs the
operation.
To reduce risk of eye or face injury from
flying chips, always wear approved safety
glasses and a face shield when operating
this machine.
8. turns the mill OFF.
If you are not experienced with this type
of machine, WE STRONGLy RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any proj-
ects. Regardless of the content in this sec-
tion, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
-26-
Model G0747/G0748 (Mfg. Since 8/12)
Table Movement
index rings
the mill table moves in three directions, as illus-
trated in Figure 16:
•
•
•
X-axis (longitudinal)
y-axis (cross)
z-axis (vertical)
these movements are controlled by table ball
handles and the z-axis crank. Additionally, the
table can be moved along the X-axis with the
power feed.
Figure 17. locations of index rings.
Table Locks
use table locks to increase the rigidity of the table
when movement in that direction is not required
for the operation.
X-Axis or Longitudinal Travel
(Left & Right)
Y-Axis or
Cross Travel
(In & Out)
refer to Figure 18 to identify the locks for each
table axis.
X-Axis locks
Z-Axis or
Vertical Elevation
(Up & Down)
z-Axis
lock
Figure 16. the directions of table movement.
(1 of 2)
Graduated Index Rings
y-Axis
lock
the table ball handles and knee crank have grad-
uated index rings (see Figure 17) that are used
to determine table movement in the increments
listed below:
Figure 18. locations of table locks for each axis.
Individual
Increment
One Full
Revolution
Axis
X
y
z
0.001"
0.001"
0.001"
0.200"
0.200"
0.100"
Always keep the table locked in place
unless table movement is required for your
operation. Unexpected table and workpiece
movement could cause the cutter to bind
with the workpiece, which may ruin the cut-
ter or the workpiece.
-27-
Model G0747/G0748 (Mfg. Since 8/12)
A. Limit Switch. stops table movement when
either of the switch side plungers are pressed
by the limit stops.
X-Axis Power Feed Identification
the mill is equipped with a power feed unit for
X-axis table movement. refer to Figure 19 and
the descriptions below to understand the func-
tions of the various components of the power feed
system.
b. Limit Stop. restricts table movement by its
positioning along the front of the table.
C. Graduated Index Ring. displays the dis-
tance of table travel in 0.001" increments,
with one full revolution equal to 0.200" of
table travel.
A
B
C
D. Feed/Jog Switch. in the left (feed) position, it
enables the power feed to operate normally.
d
While pressing the switch to the right (jog
position), the table moves in the selected
direction until the switch is released.
e
F
J
in the middle position ("0"), table movement
is disabled.
g
i
h
E. Speed Dial. Controls the speed of the power
feed. turning the dial clockwise causes the
table to move faster.
d
e
F. Direction Knob. selects the direction of table
movement. the middle position is neutral.
F
G. Rapid Traverse button. When pressed,
moves the table at full speed when it is
already in motion.
g
h
i
H. ON/OFF button. turns the power feed ON
and OFF.
Figure 19. power feed controls.
I. Circuit breaker Reset button. resets the
internal circuit breaker if the unit is overload-
ed and shuts down.
J. X-Axis ball Handle. Manually moves the
table.
-28-
Model G0747/G0748 (Mfg. Since 8/12)
X-Axis Power Feed Operation
Head Movement
Tool Needed
Qty
hex Wrench 8mm...............................................1
the head tilts 45° forward or backward, and
rotates 90° left or right (see Figures 20–21).
To operate the X-axis power feed:
1. loosen the X-axis table locks (refer to Figure
18 on Page 27 for locations).
2. secure the limit stops if needed to restrict
table movement.
Note: Make sure the cap screws firmly secure
the limit stops in place when positioned.
3. turn the speed dial all the way counterclock-
wise to the slowest setting.
4. Move the direction knob to the neutral (mid-
dle) position, press the feed/jog switch to the
left (feed position), then push the on button.
Figure 20. head tilted 45° forward.
5. With your hand poised over the oFF button in
case you need to suddenly turn the unit OFF,
move the direction knob in the desired direc-
tion of table travel.
6. use the speed dial to slowly bring the speed
of movement up to the desired rate.
7. When you are finished using the power feed:
a. turn the unit oFF.
b. rotate the speed dial all the way counter-
clockwise.
Figure 21. head rotated to the left.
c. Move the direction knob to the neutral
(middle) position to avoid unexpected
table movement later.
Tool Needed
Wrench 19mm ....................................................1
Qty
To confirm the power feed settings that you
will be using during operation, we recom-
mend that you use the power feed to move
the table through the intended cutting path
before starting the spindle rotation and tak-
ing the cut.
-29-
Model G0747/G0748 (Mfg. Since 8/12)
Rotating Head Left/Right
1. disConneCt Mill FroM poWer!
The head is heavy. When tilting or rotating
the head, get help to support the weight as
you use the controls.
2. loosen the four lock bolts shown in Figure 23.
Tilting Head Forward/backward
rotation Bolt
1. disConneCt Mill FroM poWer!
2. loosen the three tilt lock bolts shown in
Figure 22.
lock Bolts
tilt Bolt
Figure 23. head rotation controls.
3. use one hand to apply pressure to the head
in the direction of rotation, then slowly turn
the rotation bolt.
lock
Bolts
4. re-tighten the lock bolts.
Figure 22. head tilt controls.
3. use one hand to apply pressure to the head
in the direction of tilt, then slowly rotate the
tilt bolt. rotating this bolt clockwise will tilt the
head backward.
Always lock the head firmly in place after
tilting or rotating it. Unexpected movement
of the head during operations could cause
damage to the cutter or workpiece.
4. re-tighten the lock bolts.
-30-
Model G0747/G0748 (Mfg. Since 8/12)
Ram Movement
Always lock the ram firmly in place after
moving it. Unexpected movement of the ram
and head during operations could damage
the cutter or workpiece.
the ram travels forward or backward 24" and
rotates 360° around the turret.
Tool Needed
Qty
Wrench 19mm ....................................................1
Rotating Ram
1. disConneCt Mill FroM poWer!
Moving Ram Forward/backward
1. disConneCt Mill FroM poWer!
2. loosen the four lock bolts on top of the turret
(see Figure 25).
2. loosen the two lock bolts shown in Figure 24.
Note: There are two lock bolts on each side
of the ram.
lock Bolts
lock Bolts
(2 of 4)
Adjustment
rotation
scale
Bolt
Figure 24. ram forward/backward movement
controls.
Figure 25. ram rotational controls.
3. Make sure there are no obstructions to ram
travel, especially any tooling around the
workpiece, then slowly rotate the adjustment
bolt to move the ram. rotating the bolt clock-
wise will move the ram backward.
Note: In the next step, take care not to
entangle or stretch the electrical cabling as
you move the ram around the turret.
3. push on the head to manually rotate it. use
the rotation scale to determine the correct
position for your operation, then re-tighten
the four lock bolts to secure the ram in place.
4. re-tighten the lock bolts.
-31-
Model G0747/G0748 (Mfg. Since 8/12)
the procedures for setting the spindle speed for
the Models g0747 and Model g0748 differ. use
the appropriate section on the following pages for
your mill when selecting the speed range.
Spindle Speed
using the correct spindle speed is important for
safe and satisfactory results, as well as maximiz-
ing tool life.
To avoid damaging the spindle, gears, or
cutting tools when setting the spindle speed
range:
to set the spindle speed for your operation, you
will need to: (1) determine the best spindle speed
for the cutting task, and (2) configure the mill con-
trols to match the closest spindle speed.
• Spindle rotation must be turned OFF and
the spindle must be at a complete stop
bEFORE you change the spindle speed
range.
Determining Spindle Speed
Many variables affect the optimum spindle speed
to use for any given operation, but the two most
important are the recommended cutting speed for
the workpiece material and the diameter of the
cutting tool, as noted in Figure 26:
• To avoid damaging the moving parts
inside the headstock, never start spindle
rotation without the range selector detent
pin firmly seated in either the high or low
position.
• When the spindle speed range is changed,
the spindle rotation direction reverses.
you will need to either change the cutting
tool to match the direction of spindle rota-
tion or use the spindle direction switch to
compensate for the reversal.
*Recommended
Cutting Speed (FPM) x 12
= RPM
Tool Diameter (in inches) x 3.14
*
Double if using carbide cutting tool
Figure 26. spindle speed formula for milling.
Cutting speed, typically defined in feet per minute
(FpM), is the speed at which the edge of a tool
moves across the material surface.
A recommended cutting speed is an ideal speed
for cutting a type of material in order to produce
the desired finish and optimize tool life.
the books Machinery’s Handbook or Machine
Shop Practice, and some internet sites, pro-
vide excellent recommendations for which cutting
speeds to use when calculating the spindle speed.
these sources also provide a wealth of additional
information about the variables that affect cutting
speed and they are a good educational resource.
Also, there are a large number of easy-to-use
spindle speed calculators that can be found on
the internet. these sources will help you take into
account all applicable variables to determine the
best spindle speed for the operation.
-32-
Model G0747/G0748 (Mfg. Since 8/12)
3. Move the high-low range lever shown in
Setting Model G0747 Spindle Speed
Figure 28 to the high or low position.
the Model g0747 has 16 spindle speeds—eight
in low motor speed and eight in high motor speed.
setting the spindle speed involves: 1) selecting
the spindle speed range, 2) positioning the V-belt,
and 3) setting the spindle switch.
high-low
range
lever
high
low
To set the Model G0747 spindle speed:
1. Make sure the spindle is completely stopped.
2. pull the spindle speed range selector knob
(see Figure 27) out, position the selector
in the high or low position, then release the
knob to seat the knob pin in the detent.
Note: If it is difficult to move the range selec-
tor, rotate the spindle by hand to help mesh
the gears until the selector moves freely.
Figure 28. Model g0747 high-low range lever.
4. Firmly grasp the spindle, then quickly rotate it
in a back-and-forth motion until you hear/feel
the front pulley drop into the spindle clutch.
—if this step was not successful, use the
high-low range lever to re-set the speed
range, then repeat this step until you are
certain that the spindle is seated into the
spindle clutch.
5. remove the belt housing side covers on
either side of the head to expose the V-belt
and pulleys, as shown in Figure 29.
spindle speed
range selector
Figure 27. Model g0747 spindle speed range
Adjustment lever
selector in the forward (high) position.
lock lever
(1 of 2)
V-Belt & pulley
Access
Figure 29. Model g0747 V-belt and pulleys
exposed.
-33-
Model G0747/G0748 (Mfg. Since 8/12)
6. loosen the two motor lock levers, one on
each side of the head, then pull the belt ten-
sion adjustment lever forward to release the
V-belt tension.
Note: As displayed in Figure 30, the Model
G0747 has two spindle speeds for each
V-belt position depending on the spindle
switch setting.
7. refer to the illustrations in Figure 30, and
position the V-belt on the pulleys for the
desired spindle speed.
8. to re-tension the V-belt, push the adjustment
lever backward with moderate force, then
re-tighten the two lock levers to secure the
motor.
9. replace the two belt housing side covers
Low Spindle Speed Range
before re-connecting the mill to power.
Spindle Switch @
Motor
FLOW/RLOW
80
135
To avoid entanglement hazards, always
ensure belt housing safety covers are firmly
in place before connecting the mill to power.
210
325
Spindle
Switch @
FHI/RHI
10. use the chart below to find the spindle speed
range that includes the required spindle
speed for your operation and set the spindle
switch (Figure 31) accordingly.
Motor
160
270
420
Model G0747 Spindle Speed Ranges
650
low range
w/switch @ FloW/rloW
80–325 rpM
low range
160–650 rpM
w/switch @ Fhi/rhi
high range
w/switch @ FloW/rloW
660–2720 rpM
High Spindle Speed Range
high range
Spindle Switch @
1320–5440 rpM
w/switch @ Fhi/rhi
Motor
FLOW/RLOW
660
1115
1750
2720
Spindle
Switch @
Motor
FHI/RHI
1320
2230
3500
5440
Figure 31. Model g0747 spindle switch.
Figure 30. Model g0747 V-belt positions.
-34-
Model G0747/G0748 (Mfg. Since 8/12)
Setting Model G0748 Spindle Speed
the Model g0748 has variable spindle speeds
from 60 to 4200 rpM. setting the spindle speed
involves 1) selecting the spindle speed range,
and 2) using the variable-speed handwheel to
select the spindle speed.
For the Model G0748 ONLy, always make
sure that the spindle rotation has started
and is at a constant speed before using
the variable-speed handwheel to adjust the
spindle speed. Otherwise, the moving parts
inside the belt housing could be damaged
and void the warranty.
To set the Model G0748 spindle speed:
1. Make sure the spindle is completely stopped.
4. slowly rotate the speed handwheel shown
in Figure 33 until the desired speed is dis-
played in the speed indicator window for the
speed range selected.
2. pull the spindle speed range selector knob
(see Figure 32) out, position the selector
in the high or low position, then release the
knob to seat the knob pin in the detent.
Note: If it is difficult to move the range selec-
tor, rotate the spindle by hand to help mesh
the gears until the selector moves freely.
high-low range
speed indicator
Variable-speed
handwheel
spindle speed
range selector
Figure 33. Model g0748 variable-speed
controls.
Figure 32. Model g0748 spindle speed selector.
3. use the spindle switch to start spindle rota-
tion.
-35-
Model G0747/G0748 (Mfg. Since 8/12)
Spindle Downfeed
When spindle rotation is reversed, either
by changing the spindle speed range or by
using the spindle direction switch, the direc-
tion of spindle auto-downfeed will reverse.
spindle downfeed movement on the mill is con-
trolled by three mechanisms: 1) the coarse
downfeed lever, 2) the fine downfeed handwheel,
and 3) the auto-downfeed system.
D. Fine Downfeed Clutch Lever. engages the
fine/auto-downfeed gears.
Downfeed Controls
use Figure 34 and the following descriptions to
become familiar with the spindle downfeed con-
trols.
E. Downfeed Scale. used with the quill dog,
shows the depth of spindle downfeed in
inches.
F. Quill Lock Lever. secures the quill in place
A
J
for increased stability during operations.
i
G. Downfeed Stop & Locking Wheel. sets
the depth of spindle downfeed. the stop is
threaded into position, then the locking wheel
is used to secure it in place.
B
h
g
C
H. Coarse Downfeed Lever. Manually controls
quick spindle downfeed.
d
F
I. Quill Dog. Moves with the quill and spin-
dle, and disengages the downfeed clutch
lever when it contacts either the top or the
downfeed stop.
e
Figure 34. downfeed controls.
A. Auto-Downfeed Rate Selector. selects one
J. Downfeed Selector. sets the mill for manual
of the three auto-downfeed rates.
downfeed or auto-downfeed control.
b. Fine Downfeed Handwheel. Manually con-
trols slow spindle downfeed.
C. Auto-Downfeed Direction Pin. starts, stops,
and reverses the auto-downfeed direction.
-36-
Model G0747/G0748 (Mfg. Since 8/12)
4. Make sure the quill lock lever is loose so that
Coarse Downfeed
use the coarse downfeed lever to quickly move
the quill can easily move.
the spindle manually.
5. rotate the coarse downfeed lever around the
hub to control the depth of the spindle.
To use the coarse downfeed:
1. Make sure the spindle is completely stopped.
Fine Downfeed
1. Make sure the spindle is completely stopped.
2. pull the downfeed selector knob out, then
rotate it clockwise until the knob pin seats in
the forward manual (disengaged) detent (see
Figure 35).
2. pull the downfeed selector knob out, then
rotate it clockwise until the knob pin seats in
the forward manual (disengaged) detent (see
Figure 35).
Note: It may be necessary to turn the spindle
by hand as you move the selector to enable
the gears to mesh.
Note: It may be necessary to turn the spindle
by hand as you move the selector to enable
the gears to mesh.
Manual (Disengaged) Position
3. set the auto-downfeed direction pin in the
neutral (middle) position to disengage the
fine downfeed handwheel from the auto-
downfeed gears.
4. position the downfeed stop for the spindle
depth that is correct for your operation, then
secure it in place with the locking wheel.
5. use the coarse downfeed lever to lower
the spindle slightly until you can pull the
fine downfeed clutch lever out to the left
and it locks in place. this will engage the
fine downfeed handwheel with the quill and
spindle.
Figure 35. downfeed selector in manual
(disengaged) position.
3. Make sure the pin of the coarse downfeed
lever hub is engaged with one of the detents
on the downfeed sleeve (see Figure 36).
6. to lower the spindle, rotate the fine downfeed
handwheel. When the quill dog meets the
downfeed stop, the clutch lever will disen-
gage and the spindle will return to the top.
Coarse downfeed
lever hub & sleeve
Quill lock
lever
Figure 36. Coarse downfeed lever hub,
downfeed sleeve, and quill lock.
-37-
Model G0747/G0748 (Mfg. Since 8/12)
4. position the auto-downfeed direction pin in
the center of the handwheel for the spindle
travel that is correct for your operation. if nec-
essary, rock the fine downfeed handwheel
back-and-forth to move the pin all the way in
or out.
Auto-Downfeed
When using the auto-downfeed system, the spin-
dle will move in the direction you choose with the
auto-downfeed direction pin. When the quill dog
reaches the top or meets the downfeed stop, the
downfeed clutch lever will release. then, if the
spindle was traveling upward, the movement will
simply stop. if the spindle was traveling down-
ward, then the spindle will move back to the top
at a rate controlled by the return spring on the left
side of the head.
Note: The direction pin has three positions:
1) In for one downfeed direction, 2) middle
for neutral or no movement, and 3) out for
the reverse direction. The direction of spindle
travel for the in and out positions is relative to
the direction of spindle rotation. Keep in mind
that spindle rotation and downfeed direction
will reverse when the spindle speed range is
changed.
To use the auto-downfeed:
1. Make sure the spindle is completely stopped.
2. pull the downfeed selector knob out, then
rotate it clockwise until the knob pin seats
in the auto-downfeed (engaged) detent (see
Figure 37).
5. Make sure the clutch lever is all the way to
the right in the disengaged position so that
the spindle will not travel when rotation is
started.
Note: It may be necessary to turn the spindle
by hand as you move the selector to enable
the gears to mesh.
Note: We recommend that you complete
the remaining steps without a cutting tool
installed, without a workpiece in place, and
the table lower than the maximum spindle
downfeed travel. This will enable you to test
and confirm the settings before beginning the
actual cutting operation.
Auto-Downfeed (Engaged) Position
To avoid damage to the system gearing,
never use the auto-downfeed system with
spindle speeds over 1750 RPM.
6. set the mill for the correct spindle speed,
Figure 37. downfeed selector in auto-downfeed
then begin spindle rotation.
(engaged) position.
3. position the downfeed stop for the spindle
depth that is correct for your operation, then
secure it in place with the locking wheel.
-38-
Model G0747/G0748 (Mfg. Since 8/12)
Spindle brake
ALWAyS start spindle rotation before using
auto-downfeed to avoid the risk of gear
damage.
After turning the spindle switch OFF, move the
brake lever to bring the spindle to a full stop (see
Figures 39–40).
7. select one of the three downfeed rates by
pulling the knob of the auto-downfeed rate
selector out, position the selector over the
appropriate detent, then release the knob.
Make sure the pin is firmly seated by attempt-
ing to move the selector without pulling the
knob out.
To avoid premature wear of the brake sys-
tem, use the spindle brake ONLy after
power to the spindle has been turned OFF.
Note: Refer to the illustration in Figure 38
when selecting the downfeed rate.
g0747
Brake lever
Figure 39. Model g0747 brake lever.
Upper = 0.006 in./rev.
Middle = 0.0015 in./rev.
Lower = 0.003 in./rev.
g0748
Brake lever
(Rates given in inches of travel
per revolution of the spindle)
Figure 38. positions of auto-downfeed rate
selector.
8. use the coarse downfeed lever to lower the
spindle slightly until you can pull the clutch
lever out to the left and it locks in place, which
will start the auto-downfeed spindle travel.
Figure 40. Model g0748 brake lever.
To evenly wear the brake shoes, alternate
the direction you move the lever when brak-
ing.
-39-
Model G0747/G0748 (Mfg. Since 8/12)
5. With one hand holding the tool in place, insert
the drawbar into the spindle from the top of
the head, then thread it into the tool (see
Figure 42).
Loading/Unloading
Tooling
the mill is equipped with an r8 spindle taper and
head of
drawbar
a 7⁄16"-20 x 231⁄2" spindle drawbar (see Figure 41).
Figure 42. drawbar loaded
(Model g0747 shown).
Figure 41. upper portion of drawbar.
6. tighten the drawbar until it is snug. Avoid
overtightening, as this could make removing
the tool difficult.
Tools Needed
Wrench 21mm ....................................................1
Qty
Brass hammer ...................................................1
Unloading Tooling
1. disConneCt Mill FroM poWer!
Loading Tooling
1. disConneCt Mill FroM poWer!
2. place the mill in the low spindle speed range
to keep the spindle from turning in the next
step.
2. Clean any debris or surface substances from
inside the spindle taper and the mating sur-
face of the tooling.
Note: Make sure that the drawbar has at
least three threads engaged with the tool-
ing in the next step to avoid damaging the
threads of the drawbar or tool.
Note: Debris or oily substances can prevent
the tooling and spindle from properly mating.
This condition can cause excessive vibration,
poor cutting results, or tool/workpiece dam-
age.
3. loosen the drawbar a couple of turns, then
tap the top of it with a brass hammer to knock
the tool loose at the bottom of the spindle.
3. place the mill in the low spindle speed range
to keep the spindle from turning in the next
steps.
4. support the tool with one hand, then com-
pletely unthread the drawbar from the tool.
4. Align the keyway of the tool with the protrud-
ing pin inside the spindle taper, then firmly
push the tool into the spindle to seat it.
-40-
Model G0747/G0748 (Mfg. Since 8/12)
ACCessories
SECTION 5: ACCESSORIES
G1076—52-PC. Clamping Kit
this clamping kit includes 24 studs, six step block
pairs, six t-nuts, six flange nuts, four coupling
nuts, and six end hold-downs. the rack is slotted
so it can be mounted close to the machine for
easy access.
Installing unapproved accessories may
cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by Grizzly.
NOTICE
Refer to our website or latest catalog for
additional recommended accessories.
G5641—1-2-3 blocks
G9815—Parallel Set
H5556—Edge Finder Set
Figure 45. g1076 52-pC. Clamping Kit.
g5641
H6089—2 Axis Digital Read Out
(12" x 30")
H6093—3 Axis Digital Read Out
(12" x 30" x 5")
h5556
H7850—3 Axis Digital Read Out
g9815
(12" x 30" x 163⁄4")
you will be amazed the list of features for these
dros that include: selectable resolution down to
5µm, absolute/incremental coordinate display, arc
function, line of holes function, angled cuts func-
tion, 199 user defined datum points, centering/
cutter offset, double sealed scales, inches/mil-
limeters, calculator with trig functions, and linear
error compensation.
Figure 43. g5641 1-2-3 Blocks, g9815 parallel
set, and h5556 edge Finder set.
G9760—20-PC. 2 & 4 Flute TiN End Mill Set.
includes these sizes and styles in two and four
flute styles: 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/8",
3
11/16", and /4".
Figure 44. g9760 20-pC end Mill set.
Figure 46. 3 Axis digital read out.
-41-
Model G0747/G0748 (Mfg. Since 8/12)
G7155—6" Precision Milling Vise
T23962—ISO 68 Moly-D Machine Oil, 5 gal.
T23963—ISO 32 Moly-D Machine Oil, 5 gal.
Moly-d oils are some of the best we've found for
maintaining the critical components of machinery
because they tend to resist run-off and maintain
their lubricity under a variety of conditions—as
well as reduce chatter or slip. Buy in bulk and
save with 5-gallon quantities.
this swiveling milling vise features perfectly
aligned, precision-ground jaws, robust clamping
screws, and easy-to-read 0°–360° scales.
t23962
t23963
Figure 47. Model g7155 6" precision Milling
Vise.
G9299—10" yuasa-Type Rotary Table
thie high-precision, yuasa-type rotary table fea-
tures extra deep coolant channels, dual positive-
action locks, very low profiles, 10 second vernier
scales, gear drives with oil immersion, and satin
chrome dials
Figure 49. iso 68 and iso 32 machine oil.
G5562—SLIPIT® 1 Qt. Gel
G5563—SLIPIT® 12 oz Spray
G2871—boeshield® T-9 12 oz Spray
G2870—boeshield® T-9 4 oz Spray
H3788—G96® Gun Treatment 12 oz Spray
H3789—G96® Gun Treatment 4.5 oz Spray
Figure 48. Model g9299 10" yuasa-type rotary
table.
Figure 50. recommended products for
protecting unpainted cast iron/steel machinery
parts.
-42-
Model G0747/G0748 (Mfg. Since 8/12)
SECTION 6: MAINTENANCE
Daily, After Operations
•
•
disconnect the machine from power.
Vacuum/clean all chips and swarf from table,
slides, and base.
Wipe down all unpainted or machined sur-
faces with a good quality rust preventative.
To reduce risk of shock or
accidental startup, always
disconnect machine from
power before adjustments,
maintenance, or service.
•
Cleaning &
Protecting
Schedule
For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.
regular cleaning is one of the most important
steps in taking good care of this mill. each opera-
tor is responsible for cleaning the machine imme-
diately after using it or at the end of the day. We
recommend that the cleaning routine be planned
into the workflow schedule, so that adequate time
is set aside to do the job right.
Ongoing
to maintain a low risk of injury and proper
machine operation, if you ever observe any of the
items below shut the machine down immediately,
disconnect it from power, and fix the problem
before continuing operations.
typically, the easiest way to clean swarf from the
ways and table is to use a wet/dry shop vacuum
that is dedicated for this purpose only. the small
chips leftover after vacuuming can be wiped up
with a slightly oiled rag. Avoid using compressed
air to blow off chips, as this may drive them deep-
er into moving surfaces and could cause sharp
chips to fly into your face or hands.
•
•
•
•
•
loose mounting bolts or fasteners.
Worn, frayed, cracked, or damaged wires.
Missing belt guards.
reduction in braking speed or efficiency.
Any other unsafe condition.
before beginning Operations
Besides the ways and elevation leadscrew, all
other unpainted and machined surfaces should
be wiped down daily to keep them rust-free and in
top condition. this includes any surface that could
be vulnerable to rust if left unprotected (this espe-
cially includes any parts that may be exposed to
water soluble cutting fluids). typically with these
parts, a thin film of oil is all that is necessary for
protection.
•
turn the spindle direction switch to the off
(middle) position to prevent spindle startup
when connected to power (see Page 23).
Move the spindle speed range selector to
the manual (forward) position to prevent the
spindle from unexpectedly auto-downfeeding
when rotation is started (see Page 38).
Make sure the X-axis power feed is turned
OFF to prevent unintentional table movement
when connected to power (see Page 28).
perform lubrications tasks as directed in the
lubrication section on Page 44.
•
•
Keep tables rust-free with regular applications of
products like g96® gun treatment, slipit®, or
Boeshield® t-9 (see Section 5: Accessories on
Page 42 for more details).
•
•
Check table movement in all three axes
directions for loose/tight gibs. Adjust the gibs
if necessary (see Page 51).
-43-
Model G0747/G0748 (Mfg. Since 8/12)
Lubrication
Failure to follow reasonable lubrication
practices as instructed in this manual for
the mill could lead to premature failure of
the mill and will void the warranty.
the mill has numerous moving metal-to-metal
contacts that require regular and proper lubrica-
tion to ensure efficient and long-lasting operation,
and to protect your investment.
Quill
other than the lubrication points covered in this
section, all other bearings are internally lubricated
and sealed at the factory. simply leave them
alone unless they need to be replaced.
oil type ...... Model t23962 or iso 68 equivalent
oil Amount.......................................... Fill oil Cup
Check/Add Frequency............4 hrs. of operation
lift the quill oil cup cap shown in Figure52 to add
10 drops of lubricant.
Before performing any lubrication task,
disConneCt the Mill FroM poWer!
Important: Before adding lubricant, clean the
debris and grime from the oil cup or grease fitting
and the immediate area to prevent contamination
of the new lubricant.
use the schedule and information in Figure 51
as a daily guide for lubrication tasks. Follow the
referenced sections on the following pages for
detailed instructions.
Quill oil Cup
The following recommended lubrication
schedule is based on light to medium mill
usage. Keeping in mind that lubrication
helps to protect the value and operation of
the mill, you may need to perform the lubri-
cation tasks more frequently depending on
your usage.
Figure 52. Quill oil cup.
Frequency
(Hours of
Operation)
Page
Ref.
Lubrication Task
This
Page
Quill
4 hrs.
table Ways (one-shot
oiler)
4–8 hrs.
45
headstock gearing
40 hrs.
45
46
ram Ways
40 hrs.
table elevation leadscrew
(z-Axis)
40 hrs.
46
power Feed gears
160 hrs.
47
Figure 51. recommended lubrication tasks,
schedules, and instruction page references.
-44-
Model G0747/G0748 (Mfg. Since 8/12)
Table Ways (One-Shot Oiler)
oil type ...... Model t23962 or iso 68 equivalent
oil Amount................... one pull of pump handle
Check/Add Frequency........4–8 hrs. of operation
Headstock Gearing
grease type ........................nlgi 2 or equivalent
grease Amount .........two pumps of grease gun
Check/Add Frequency..........40 hrs. of operation
the one-shot oiler is connected to a series of alu-
minum tubes that carry the lubricant to wear points
along the table horizontal and vertical ways.
Add two pumps from a grease gun to the grease
fittings that are shown in Figures 54–55.
pull the handle out slowly then release it to send
the oil through the tubes (see Figure 53), then
move the table through all paths of movement to
evenly distribute the lubricant.
use the sight glass on the side of the oiler to know
when to re-fill the reservoir.
reservoir Cap
g0747
grease Fitting
Figure 54. Model g0747 headstock gearing
grease fitting.
pump
handle
sight glass
Figure 53. one-shot oiler.
g0748
grease Fitting
Figure 55. Model g0748 headstock gearing
grease fitting.
-45-
Model G0747/G0748 (Mfg. Since 8/12)
Ram Ways
oil type ...... Model t23962 or iso 68 equivalent
oil Amount............................................ thin Coat
Check/Add Frequency..........40 hrs. of operation
Table Elevation Leadscrew
grease type ........................nlgi 2 or equivalent
grease Amount .................................... thin Coat
Check/Add Frequency..........40 hrs. of operation
Move the ram back and forth as necessary to
access the full length of the ways (see Figure 56),
then use a clean shop rag to apply a thin coat of
lubricant to the ways.
elevate the table all the way up, then use mineral
spirits to clean any debris and built-up grime from
the elevation leadscrew threads. Add one pump
from a grease gun to the leadscrew grease fitting
shown in Figure 58, then run the table up and
down to distribute the grease. repeat this process
until the entire leadscrew is well lubricated.
ram Ways
leadscrew
grease
Fitting
Figure 56. ram ways.
Head Tilt & Ram Pinions
the interaction between the cast iron surfaces
of these devices (see Figure 57) produces a dry
powder that provides an adequate lubrication.
Figure 58. elevation leadscrew grease fitting.
do not apply any other lubricant that could pro-
duce a stiff compound, which may interfere with
smooth movement.
head tilt
rack & pinion gear
ram
pinion gear
Figure 57. head tilt and ram pinions.
-46-
Model G0747/G0748 (Mfg. Since 8/12)
5. Brush a light coat of lubricant on the teeth
of the bevel gear and the smaller drive gear
(see Figure 61).
Power Feed Gears
grease type ........................nlgi 2 or equivalent
grease Amount .........two pumps of grease gun
Check/Add Frequency........ 160 hrs. of operation
Brass Bevel gear
Tool Needed
Qty
Wrench 19mm ....................................................1
To lubricate the power feed gears:
1. disConneCt Mill FroM poWer!
2. remove the hex nut and ball handle from the
power unit end of the X-axis leadscrew (see
Figure 59).
drive gear
graduated
dial ring
Figure 61. power feed brass bevel gear and
drive gear.
leadscrew
6. replace the leadscrew alignment key, then
align the bevel gear keyway and the key as
you slide the gear onto the leadscrew and
mesh its teeth with the drive gear.
retaining ring
7. replace the graduated dial ring into position
and secure it with the knurled retaining ring—
do not overtighten.
Figure 59. power feed ball handle removed.
8. slide the ball handle onto the leadscrew
as you align its keyway with the leadscrew
alignment key, then secure it with the hex nut
removed in Step 2.
3. unthread and remove the knurled retaining
ring and graduated dial ring from the end of
the leadscrew.
4. remove the brass bevel gear from the
leadscrew, then remove the leadscrew align-
ment key (see Figure 60).
9. Manually move the table with the power feed
ball handle to check the gear movement and
to distribute the grease on the gears. if the
movement is not smooth, repeat Steps 2–8
until it is.
Alignment Key
Brass Bevel gear
Figure 60. power feed brass gear and
leadscrew alignment key.
-47-
Model G0747/G0748 (Mfg. Since 8/12)
•
•
loosen the belts to prevent them from stretch-
ing during storage. post a reminder on the
mill that the belts need to be re-tensioned
before resuming operations.
Machine Storage
to avoid rust problems or corrosion damage, use
the following information to protect your invest-
ment when storing the mill for any length of time.
Cover and place the machine in a dry area
that is out of direct sunlight and away from
hazardous fumes, paint, solvents, or gas.
Fumes and sunlight can bleach or discolor
paint and plastic parts.
•
•
disConneCt Mill FroM poWer!
lubricate the mill as directed in the lubrication
section beginning on Page 44.
•
At least once a month, start the mill and run
all gear-driven components for a few minutes.
this will keep the bearings, bushings, gears,
and shafts well lubricated and protected
from corrosion, especially during the winter
months.
•
thoroughly clean all unpainted, bare metal
surfaces, then coat them with a light weight
grease or rust preventative. take care to
ensure these surfaces are completely cov-
ered but that the grease or rust preventative
is kept off painted surfaces.
Note: If the machine will be out of service
for only a short period of time, use way oil or
a good grade of medium-weight machine oil
(not auto engine oil) in place of the grease or
rust preventative.
-48-
Model G0747/G0748 (Mfg. Since 8/12)
SECTION 7: SERVICE
Review the troubleshooting and procedures in this section if a problem develops with your machine. If you
need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663.
Note: Please gather the serial number and manufacture date of your machine before calling.
Troubleshooting
Symptom
Possible Cause
Possible Solution
Machine does not
start or a breaker
trips.
1. plug/receptacle at fault or wired incorrectly. 1. test for good contacts; correct the wiring.
2. power supply is switched OFF or at fault.
2. ensure hot lines have correct voltage on all legs
and main power supply is switched ON.
3. Correct motor wiring connections (Pages 57 & 58).
4. replace faulty spindle switch.
3. Motor connections wired incorrectly.
4. spindle switch at fault.
5. Motor windings or motor at fault.
5. replace motor.
Machine stalls or is 1. Machine undersized for task.
1. use smaller, sharp tools; reduce feed rate; reduce
overloaded.
spindle speed; use coolant.
2. Workpiece not securely clamped to table or 2. Make sure workpiece is properly clamped to table or
mill vise.
mill vise; use work holding jig if necessary.
3. dull, damaged or incorrect cutting tool.
4. spindle speed is incorrect for operation.
5. Motor connections wired incorrectly.
3. use sharp and correct cutting tool for operation.
4. select appropriate spindle speed (Page 33 or 35).
5. Correct motor wiring connections (Pages 57 & 58).
6. plug/receptacle at fault or wired incorrectly; 6. test for good contacts; correct wring problems;
incorrect voltage from power supply.
ensure hot lines have correct voltage on all legs.
7. re-align/replace shaft, pulley, set screw, or key as
required.
7. pulley loose.
8. Motor bearings at fault.
8. test by rotating shaft; rotation grinding/loose shaft
requires bearing replacement.
9. Motor overheated.
9. let motor cool, clean off, and reduce workload.
10. replace motor.
10. Motor at fault.
Machine has
vibration or noisy
operation.
1. tool holder or cutter at fault.
1. replace out-of-round tool holder; replace/re-
sharpen cutter; use appropriate feed rate and
spindle speed.
2. Workpiece alignment poor.
2. eliminate workpiece bindings; use vise or clamps as
required for proper workpiece alignment control.
3. spindle and spindle clutch are not properly 3. Make sure the spindle and spindle clutch are
meshed.
properly meshed.
4. Motor or component loose.
4. inspect/replace stripped or damaged bolts/nuts, and
re-tighten with thread-locking fluid.
5. re-align/replace shaft, pulley, set screw, or key as
required.
5. pulley loose.
6. Machine incorrectly mounted to floor or sits 6. re-tighten/replace mounting bolts in floor; relocate/
unevenly.
shim machine.
7. Motor bearings at fault.
7. test by rotating shaft; rotation grinding/loose shaft
requires bearing replacement.
8. gearbox at fault.
8. rebuild gearbox and replace worn/damaged gears
and bearings.
-49-
Model G0747/G0748 (Mfg. Since 8/12)
Symptom
Possible Cause
Possible Solution
tool slips in collet.
1. Collet not fully drawn into spindle taper.
2. Wrong size collet.
1. snug up drawbar to fully seat collet.
2. use correct collet for tool shank diameter.
3. remove oil and debris from mating surface, then
re-install.
3. debris on mating surface of collet and
spindle.
4. excessive depth of cut.
4. decrease depth of cut and allow chips to clear.
tool breakage.
1. spindle speed too slow or feed rate too
1. use correct spindle speed (Page 33 or 35) and feed
rate.
fast.
2. tool getting too hot.
2. use coolant; reduce spindle speed (Page 33 or 35)
or feed rate.
3. excessive depth of cut.
3. decrease depth of cut and allow chips to clear.
Workpiece chatters 1. table locks not tight.
or vibrated during
1. tighten all locks on mill that are not associated with
necessary table movement for the operation.
operation.
2. Workpiece not securely clamped to table or 2. Check that clamping is tight and sufficient for
mill vise.
operation; make sure mill vise is clamped tight to
table.
3. tool not secure or is damaged.
3. properly secure the tool; replace if damaged.
4. use correct spindle speed (Page 33 or 35) and feed
rate
4. spindle speed too fast; feed rate too slow.
5. gibs too loose.
5. properly adjust gibs (Page 51).
table hard to move. 1. table locks are tightened down.
2. Chips have loaded up on ways.
3. Ways are dry and in need of lubrication
4. gibs too tight.
1. loosen locks needed for movement.
2. Frequently clean away chips from ways.
3. use one-shot oiler to lubricate ways (Page 45).
4. properly adjust gibs (Page 51).
Bad surface finish.
1. incorrect spindle speed or feed rate.
1. use correct spindle speed Page 33 or 35) and feed
rate.
2. dull, damaged or incorrect cutting tool.
2. use sharp and correct cutting tool for operation.
3. Check for correct spindle rotation for tool.
3. Wrong spindle direction for tool.
4. Workpiece not securely clamped to table or 4. Make sure workpiece is properly clamped to table or
mill vise.
mill vise; use work holding jig if necessary.
5. gibs too loose.
5. properly adjust gibs (Page 51).
power feed chatters 1. Brass bevel gear is not meshed with drive
1. remove parts from power feed side of X-axis
leadscrew to ensure bevel gear is properly meshed
with drive gear; make sure ball handle nut is snug.
2. replace power feed unit.
or grinds during
operation.
gear.
2. power feed unit at fault.
-50-
Model G0747/G0748 (Mfg. Since 8/12)
Adjusting Gibs
gibs are tapered lengths of metal that are sand-
wiched between two moving surfaces. gibs con-
trol the gap between these surfaces and how they
slide past one another. Correctly adjusting the
gibs is critical to producing good milling results.
table gib &
tight gibs make table movement more accurate
but stiff. loose gibs make moving the table sloppy
but easier to do. the goal of gib adjustment is to
remove unnecessary sloppiness without causing
the ways to bind.
Adjustment screw
Figure 62. table gib and adjustment screw
underneath left side of table.
gibs are adjusted with a screw on each end of
the gib, that move the tapered gib back-and-forth
to increase or decrease the friction pressure
between the sliding surfaces. the process of
properly adjusting the gibs requires trial-and-error
and patience.
saddle gib &
Adjustment screw
disConneCt Mill FroM poWer BeFore
AdJusting the giBs!
Make sure all table and knee locks are loose.
then, loosen one gib adjustment screw and
tighten the other the same amount to move the
gib. use the ball handles/crank to move the table/
knee until you feel a slight drag in that path of
movement.
Figure 63. saddle gib and adjustment screw.
refer to Figures 62–64 to identify the locations of
the table, saddle, and knee gibs, and one of the
two adjustment screws for each.
Knee gib &
Adjustment screw
Note: It will be necessary to remove small parts,
such as way wipers and covers, to access the gib
adjustment screws.
Figure 64. Knee gib and adjustment screw.
-51-
Model G0747/G0748 (Mfg. Since 8/12)
X-Axis Leadscrew backlash
1. disConneCt Mill FroM poWer!
Adjusting Leadscrew
backlash
2. loosen the two cap screws on the X-axis
leadscrew nut accessed from underneath the
left side of the table (see Figure 65).
leadscrew backlash is the amount of motion the
leadscrew rotates before the attached device
begins to move.
leadscrews will always have a certain amount
of backlash that will increase with normal wear.
generally, 0.005"–0.010" leadscrew backlash is
acceptable to ensure smooth movement and
reduce the risk of premature thread wear. however,
if you find it necessary to adjust leadscrew back-
lash, perform the procedures listed below.
Cap screws
Tools Needed
Qty
t-handle hex Wrench 5mm...............................1
hex Wrench 3mm...............................................2
hex Wrench 8mm...............................................1
Wrench 19mm ....................................................1
Figure 65. X-axis leadscrew nut cap screws
(viewed from underneath left side of table).
3. rotate the adjustment plate on the leadscrew
nut in small increments, then check the
amount of backlash.
4. When you are satisfied with the adjustment,
re-tighten the two cap screws.
-52-
Model G0747/G0748 (Mfg. Since 8/12)
5. loosen the two cap screws on the face of the
Cross Leadscrew backlash
1. disConneCt Mill FroM poWer!
leadscrew nut shown in Figure 68.
2. remove the hex nut and ball handle from the
y-axis leadscrew.
Note: In the next step, take care not to mis-
place the leadscrew key as you remove the
parts.
3. unthread and remove the knurled retaining
ring, graduated dial ring, and the leadscrew
key (see Figure 66).
y-Axis leadscrew nut
& Cap screws
Figure 68. y-axis leadscrew nut and cap screws.
6. re-install the key back onto the leadscrew so
that you can use the ball handle in the next
step.
7. rotate the adjustment plate on the leadscrew
nut in small increments, slide the ball handle
on the leadscrew, then check the amount of
backlash.
y-Axis
leadscrew
8. When you are satisfied with the adjustment,
Figure 66. Ball handle, ring, and key removed
re-tighten the two cap screws.
from y-axis leadscrew.
9. re-install the parts previously removed in the
4. remove the four cap screws from the bearing
housing, then slide it off the leadscrew (see
Figure 67).
reverse order.
Note: It may be necessary to use a dead
blow hammer or rubber mallet on the housing
to knock it loose.
Bearing
housing
Figure 67. y-axis bearing housing.
-53-
Model G0747/G0748 (Mfg. Since 8/12)
Note: A precision-ground plate can be substi-
tuted for the parallel blocks. Keep in mind that
the farther the indicator point can be placed from
the spindle axis, the more accurate the alignment
measurements will be.
Tramming Spindle
After positioning the head at an angle and when
your operation requires that the spindle axis be
precisely perpendicular to the table, you must
tram or align the spindle with the table to ensure
the spindle is exactly 90° to the table.
To tram the spindle to the table:
1. disConneCt Mill FroM poWer!
this procedure involves mounting a dial test
indicator to the quill or spindle, rotating it around
the table, and adjusting the spindle axis (z-axis)
90° to the table X- and y-axes, as illustrated in
Figure 69.
2. prepare the mill for tramming by performing
the following tasks:
• Verify the table is clean by running your
hand over the top of it. if necessary, stone
the table to remove all nicks and burrs,
then clean off all debris.
Spindle
Z-Axis
• position the table for the milling operation
you intend to perform after tramming—
preferably centered with the saddle.
• tighten any table, knee, quill, or ram locks
that should be tight during the intended
milling operation.
Y-Axis
90º
90º
X-Axis
3. place the parallel block underneath the spin-
Table
dle.
4. install the indicator holder in the spindle or on
the quill, then mount the indicator so that the
point is as parallel to the block as possible
(see the illustration in Figure 70).
Figure 69. spindle z-axis perpendicular to the
table X- and y-axis.
We encourage you to research the many varia-
tions of spindle tramming to find the one that
works best for you. if you do not already have a
preference for performing this operation, use the
following widely-used procedure for accurately
tramming the spindle to the table.
Indicator Holder
Spindle
Dial Test
Indicator
Keep in mind that all workpiece top surfaces are
not exactly parallel with the table top. you may
choose to tram the spindle to the top surface of
the workpiece after it is mounted instead of that
of the table.
Parallel Block
Table
Tools Needed
Qty
dial test indicator
(with at least 0.0005" resolution) .................1
indicator holder
Figure 70. dial test indicator mounted.
(mounted on the quill/spindle) .....................1
precision parallel Block
(at least 9" in length)....................................1
-54-
Model G0747/G0748 (Mfg. Since 8/12)
5. to measure spindle alignment along the
X-axis, place the parallel block directly under
the spindle and indicator across the length of
the table, as illustrated in Figure 71.
Note: Keep one of the rotation lock bolts
just snug so the head does not move loosely
while you adjust it. Remember to tighten
all the rotation lock bolts after adjusting the
head.
Note: If you must re-position the quill or the
knee to accommodate the above step, then
review the tasks in Step 2 to make sure the
mill is properly prepared for tramming.
8. place the parallel block directly under the
spindle and across the width of the table, as
illustrated in Figure 72.
Table (Top View)
Parallel Block
Table (Top View)
Indicator
Spindle
Indicator
Spindle
Parallel Block
Figure 71. parallel block and indicator positioned
for the X-axis measurement
(top view).
Figure 72. parallel block and indicator positioned
for the y-axis measurement
(top view).
Note: Your general goal in the next steps
should be to get the difference of the indicator
readings between the ends of the parallel bar
down to 0.0005". However, the acceptable
variance will depend on the requirements for
your operation.
9. rotate the spindle so the indicator point rests
on the parallel bar, as illustrated in Figure 72,
then zero the dial.
10. rotate the spindle so that the indicator point
rests on the other end of the bar in the same
manner, then read the dial.
6. rotate the spindle by hand so that the indi-
cator point rests on one end of the parallel
block, as illustrated in Figures 70–71, then
zero the dial.
—if the indicator dial still reads zero or is
within the acceptable variance, the spindle
is precisely perpendicular to the table in
both the X- and y-axes, and the tramming
procedure is complete.
7. rotate the spindle so that the indicator point
rests in the same manner on other end of the
block, then read the dial.
—if the indicator dial has moved from zero
beyond the acceptable variance, you will
need to compensate for that amount by tilt-
ing the head forward or backward. repeat
Steps 9–10 until you are satisfied with
the spindle axis alignment along the table
y-axis.
—if the indicator dial still reads zero or is
within the acceptable variance, continue on
with Step 8.
—if the indicator dial has moved from zero
beyond the acceptable variance, you will
need to compensate for that amount by
rotating the head left or right. repeat Steps
6–7 until you are satisfied with the spindle
axis alignment along the table X-axis.
Note: Keep one of the tilt lock bolts just snug
so the head does not move loosely while you
adjust it. Remember to tighten all the tilt lock
bolts after adjusting the head.
-55-
Model G0747/G0748 (Mfg. Since 8/12)
machine
SECTION 8: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make chang-
es to the electrical systems of future machines. Compare the manufacture date of your machine to the one
stated in this manual, and study this section carefully.
If there are differences between your machine and what is shown in this section, call Technical Support at
(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
Wiring Safety Instructions
SHOCK HAZARD. Working on wiring that is con- WIRE/COMPONENT DAMAGE. Damaged wires
nected to a power source is extremely dangerous. or components increase the risk of serious per-
Touching electrified parts will result in personal sonal injury, fire, or machine damage. If you notice
injury including but not limited to severe burns, that any wires or components are damaged while
electrocution, or death. Disconnect the power performing a wiring task, replace those wires or
from the machine before servicing electrical com- components.
ponents!
MOTOR WIRING. The motor wiring shown in
MODIFICATIONS. Modifying the wiring beyond these diagrams is current at the time of printing
what is shown in the diagram may lead to unpre- but may not match your machine. If you find this
dictable results, including serious injury or fire. to be the case, use the wiring diagram inside the
This includes the installation of unapproved after- motor junction box.
market parts.
CAPACITORS/INVERTERS. Some capacitors
WIRE CONNECTIONS. All connections must and power inverters store an electrical charge for
be tight to prevent wires from loosening during up to 10 minutes after being disconnected from
machine operation. Double-check all wires dis- the power source. To reduce the risk of being
connected or connected during any wiring task to shocked, wait at least this long before working on
ensure tight connections.
capacitors.
CIRCUIT REQUIREMENTS. You MUST follow EXPERIENCING DIFFICULTIES. If you are expe-
the requirements at the beginning of this man- riencing difficulties understanding the information
ual when connecting your machine to a power included in this section, contact our Technical
source.
Support at (570) 546-9663.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
-56-
Model G0747/G0748 (Mfg. Since 8/12)
G0747 Wiring Diagram
Hot
Ground
SPINDLE SWITCH
G
Hot
Z
X
220 VAC
W
3-Phase
NEMA 15-15 Plug
Hot
Ground
(As Recommended)
S
T
R
S
T
R
FRONT
6
5
3
2
4
1
6
5
3
2
4
1
4
5
2W
1W
6
2U
2V
Ground
1V
1U
3
2
1
READ ELECTRICAL SAFETY
ON PAGE 56!
-57-
Model G0747/G0748 (Mfg. Since 8/12)
G0748 Wiring Diagram
Hot
Ground
SPINDLE SWITCH
G
Hot
Z
S
X
220 VAC
3-Phase
NEMA 15-15 Plug
W
Hot
8
7
V
3
Ground
(As Recommended)
FRONT
T
S
R
T
S
6
R
W
U
T
R
MOTOR
1U
2U
2W
1W
R
S
1V
2V
T
Ground
READ ELECTRICAL SAFETY
ON PAGE 56!
-58-
Model G0747/G0748 (Mfg. Since 8/12)
SECTION 9: PARTS
Main
8
4
7
10
9
6
2
1
13
14
127
128
129
16
126
125
132
118
17
15
23
133
18
119
19
131
124
32
120
37
123
33
43
38
31
52
39
40
53
41
49
42
55
46
56
57
47
50
58
51
48
64
98
54
105
44
60
75
77
62
61
65
69
74
71
104
103
76
82
102
80
135
134
138
81
90
79
135
137
136
91
92
93
96
85
84
86
89
87
83
88
94
95
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
-59-
Model G0747/G0748 (Mfg. Since 8/12)
Main Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
P07470001
P07470002
P07470004
P07470006
P07470007
P07470008
PK36M
QUILL HOUSING ADJUSTMENT GEAR
RAM ADAPTER
71
P07470071
PN13
KNEE PLUG
2
74
HEX NUT 1/2-13
4
LIFTING EYE BOLT 28MM DIA M10-1.5 X 35
HEAD TILT ADJUSTING WORM
THRUST WASHER 14MM
HEAD TILT ADJUSTING WORM SHAFT
KEY 5 X 5 X 50
75
PK34M
KEY 5 X 5 X 20
6
76
PW01
FLAT WASHER 1/2
7
77
P07470077
P3305
Z-AXIS BEVEL GEAR
ANGULAR CONTACT BEARING 3305
BEARING RETAINER RING
CAP SCREW M6-1 X 20
Z-AXIS LEADSCREW
CRANK HANDLE
8
79
9
80
P07470080
PCAP02M
P07470082
P07470083
P07470084
P07470085
P07470086
P07470087
P07470088
PCAP02M
P07470090
P6204ZZ
10
13
14
15
16
17
18
19
23
31
32
33
37
38
39
40
41
42
43
44
46
47
48
49
50
51
52
53
54
55
56
57
58
60
61
62
64
65
69
P07470010
PCAP13M
PRP08M
RAM CASTING
81
CAP SCREW M8-1.25 X 30
ROLL PIN 6 X 30
82
83
P07470015
PRIV001M
P07470017
PW10M
HEAD TILT SCALE
84
Z-AXIS CRANK ARM
CLUTCH
STEEL FLUTED RIVET 2 X 5MM
RAM ADAPTER PIVOT BOLT M28.5 X 181.5
FLAT WASHER 14MM
85
86
DIAL LOCK NUT
87
GRADUATED DIAL
PB197M
HEX BOLT M14-2 X 190
TABLE 10" X 50"
88
DIAL HOLDER
P07470023
P07470031
P07470032
PN09M
89
CAP SCREW M6-1 X 20
BEARING RETAINER RING
BALL BEARING 6204ZZ
BEARING CAP
LIMIT STOP T-BOLT
90
LIMIT STOP
91
HEX NUT M12-1.75
92
P07470092
PK102M
P07470037
P07470038
P07470039
PCAP146M
P07470041
P07470042
P07470043
P07470044
P07470046
P07470047
P07470048
P07470049
P07470050
PS14M
SADDLE LOCK BOLT HANDLE
SADDLE LOCK BOLT
93
KEY 4 X 4 X 18
94
P07470094
P6204ZZ
Z-AXIS SHAFT
SADDLE LOCK BOLT PLUNGER
CAP SCREW M10-1.5 X 15
GIB ADJUSTING SCREW
TABLE STOP BRACKET
TABLE GIB
95
BALL BEARING 6204ZZ
BEVELED PINION GEAR
COLUMN CASTING
CAP SCREW M10-1.5 X 40
Z-AXIS PEDESTAL
96
P07470096
P07470098
PCAP47M
P07470103
P07470104
PCAP02M
P07470118
P07470119
P07470120
PW06M
98
102
103
104
105
118
119
120
123
124
125
126
127
128
129
131
132
133
134
135
136
137
138
SADDLE WAY WIPER
Z-AXIS LEADSCREW NUT
CAP SCREW M6-1 X 20
RAM SWIVEL
TABLE LOCK BOLT PLUNGER
TABLE LOCK BOLT
TABLE LOCK BOLT HANDLE
SADDLE GIB
RAM LOCK BOLT M16-2 X 35
RAM PINION
SADDLE WIPER HOLDER
PHLP HD SCR M6-1 X 12
SADDLE CASTING
FLAT WASHER 12MM
TURRET
P07470124
P07470125
P07470126
P07470127
P07470128
P07470129
P07470131
P07470132
PN02M
P07470052
P07470053
P07470054
P07470055
PCAP26M
P07470057
P07470058
P07470060
P07470061
P07470062
P07470064
P07470065
P07470069
RAM CLAMP BAR
LEFT COLUMN WAY WIPER HOLDER
LEFT COLUMN WAY WIPER
KNEE GIB
UNTAPPED RAM CLAMP
TAPPED RAM CLAMP
DOWEL PIN 13.5 X 26
RAM LOCK BOLT M12-1.75 X 185
RAM GIB
CAP SCREW M6-1 X 12
RIGHT COLUMN WAY WIPER HOLDER
RIGHT COLUMN WAY WIPER
UPPER SADDLE COVER
LOWER SADDLE COVER
KNEE CASTING
RAM GIB ADJUSTMENT SET SCREW
HEX NUT M10-1.5
P07470134
PBHS13M
PN06M
COLUMN WAY COVER
BUTTON HED CAP SCR M5-.8 X 18
HEX NUT M5-.8
KNEE STOP BOLT
KNEE LOCK BOLT ASSEMBLY
KNEE LOCK PLUNGER
PW02M
FLAT WASHER 5MM
FRONT SADDLE WAY COVER
P07470138
-60-
Model G0747/G0748 (Mfg. Since 8/12)
X- & y-Axis Leadscrews
207
212
208
215
214
209
221
206
220
210
226
229
222
216
201
209
211
218
205
217
202
210
203
226
216
205
204
223
209
219
216
224
229
214
201
214
203
205
218
208
227
209
204
217
203
202
228
229
202
208
201
210
226
206
207
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
201
202
203
204
205
206
207
208
209
210
211
212
214
215
PN13
HEX NUT 1/2-13
216
217
218
219
220
221
222
223
224
226
227
228
229
PFH73M
FLAT HD CAP SCR M6-1 X 12
CAP SCREW M6-1 X 25
FLAT WASHER 6MM
P07470202
P07470203
P07470204
P07470205
PCAP01M
P07470207
P6204ZZ
BALL CRANK HANDLE
DIAL LOCK NUT
PCAP06M
PW03M
GRADUATED DIAL
DIAL HOLDER
P07470219
P07470220
PCAP64M
P07470222
P07470223
P07470224
P07470226
P07470227
P07470228
PLW07
LEFT X-AXIS LEADSCREW NUT
RIGHT X-AXIS LEADSCREW NUT
CAP SCREW M10-1.5 X 25
LEADSCREW NUT BRACKET
REAR Y-AXIS LEADSCREW NUT
FRONT Y-AXIS LEADSCREW NUT
BALL CRANK
CAP SCREW M6-1 X 16
BEARING RETAINER RING
BALL BEARING 6204ZZ
ROLL PIN 5 X 30
PRP05M
PCAP64M
P07470211
P07470212
PK92M
CAP SCREW M10-1.5 X 25
LEFT X-AXIS LEADSCREW BRACKET
RIGHT X-AXIS LEADSCREW BRACKET
KEY 3 X 3 X 25
Y-AXIS LEADSCREW
Y-AXIS LEADSCREW BRACKET
LOCK WASHER 1/2
P07470215
X-AXIS LEADSCREW
-61-
Model G0747/G0748 (Mfg. Since 8/12)
Downfeed System
312
313
316
314
311
317
315
308
307
304
324
303
320 322
321
302
301
319
318
309
327
305
323
306
494
310
495
328
325
491
336
331
332
333
329
489
477
493
492
490
488
487
486
344
481
338
482
347
334
335
349
337
348
350
340
351
342
476
343
485
475
472
359
360
341
484
483
478
357
356
363
352
469
366
367
355
362
361
471
465
384
385
480
466
468
463
458
383
371
369 368
456
382
364
455
453
370
457
381
377
372
376
387
386
390
375
464
391
392
394
373
400
401
380
379
374
388
389
418
393 417
415
462
461
448
452
416
414
378
446
413
397
398
420
421
459
451
396
412
419
395
399
403
404
445
444
460
423
406
407
408
409
411
427
410
424
405
440
425
442
428
441
438
437
429
430
436
435
431
434
433
432
-62-
Model G0747/G0748 (Mfg. Since 8/12)
Downfeed System Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
301 PS31
PHLP HD SCR 10-24 X 1-3/4
362 PK52M
KEY 3 X 3 X 15
302 P07470302 BEVEL PINION FLAT WASHER
303 P07470303 FEED BEVEL PINION
363 P07470363 FEED GEAR SHIFT CRANK
364 P07470364 CLUSTER GEAR SHIFT CRANK
366 P07470366 CLUSTER GEAR COVER
367 PCAP33M CAP SCREW M5-.8 X 12
368 P07470368 GEAR SHIFT PLUNGER
369 P07470369 COMPRESSION SPRING
370 P07470370 SHIFT CRANK
304 P07470304 FEED WORM GEAR SHAFT SLEEVE
305 P07470305 WORM CRADLE BUSHING
306 PSS07
SET SCREW 1/4-20 X 1/2
307 P07470307 WORM CRADLE SPACER
308 P07470308 FEED DRIVE WORM GEAR
309 P07470309 FEED DRIVE WORM GEAR SHAFT
371 PRP42M
ROLL PIN 3 X 20
310 PK39M
311 PK98M
KEY 3 X 3 X 10
KEY 3 X 3 X 16
372 P07470324 ROUND PLASTIC KNOB 1/4-20 1" OD
373 PCAP79M CAP SCREW M5-.8 X 35
374 P07470374 CLUTCH RING PIN
312 P07470312 BEVEL GEAR LOCK BOLT
313 PW01M
314 PK39M
FLAT WASHER 8MM
KEY 3 X 3 X 10
375 P07470375 CLUTCH RING
376 PSS03M
SET SCREW M6-1 X 8
315 P07470315 FEED REVERSE BEVEL GEAR
316 P07470316 FEED ENGAGEMENT PIN
317 P07470317 WORM GEAR CRADLE
318 P07470318 WORM GEAR CRADLE THROW-OUT
319 P07470319 SHIFT SLEEVE
377 P07470377 BRASS PLUG
378 P07470378 OVERLOAD CLUTCH LOCKNUT
379 P07470379 SAFETY CLUTCH COMPRESSION SPRING
380 P07470380 OVERLOAD CLUTCH
381 P07470381 OVERLOAD CLUTCH SLEEVE
320 P07470320 GEAR SHIFT PLUNGER
321 P07470321 COMPRESSION SPRING
382 PLW02M
383 PS56M
384 PSS04M
385 PSS03M
386 PSS02M
387 PSS01M
LOCK WASHER 4MM
PHLP HD SCR M4-.7 X 16
SET SCREW M6-1 X 12
SET SCREW M6-1 X 8
SET SCREW M6-1 X 6
SET SCREW M6-1 X 10
322 PRP42M
ROLL PIN 3 X 20
323 P07470323 SHIFT CRANK
324 P07470324 ROUND PLASTIC KNOB 1/4-20 1" OD
325 PCAP33M CAP SCREW M5-.8 X 12
327 P07470327 CLUSTER GEAR SHAFT BRASS SLEEVE
328 P07470328 CLUSTER COMBO GEAR
388 P07470388 COMPRESSION SPRING
389 P07470389 OVERLOAD CLUTCH LEVER SPRING PLUNGER
390 P07470390 QUILL PINION SHAFT BUSHING
391 P07470391 PINION SHAFT WORM GEAR SPACER
392 P07470392 OVERLOAD CLUTCH WORM GEAR
393 P07470393 OVERLOAD CLUTCH RING
329 PK53M
331 P07470331 CLUSTER GEAR SHAFT
332 PR06M EXT RETAINING RING 16MM
KEY 3 X 3 X 45
333 P07470333 BEVEL GEAR BRASS SLEEVE
334 P07470334 BEVEL GEAR THRUST WASHER
335 P07470335 FEED REVERSE BEVEL PINION
336 P07470336 FEED DRIVE GEAR SHAFT 18T
394 PR02M
EXT RETAINING RING 14MM
395 P07470395 DOWEL PIN
396 P07470396 OVERLOAD CLUTCH TRIP LEVER
337 PK39M
KEY 3 X 3 X 10
397 PW04M
398 PR01M
FLAT WASHER 10MM
338 P07470338 CLUSTER GEAR INPUT SHAFT
340 P07470340 FEED DRIVE GEAR 23T
341 P07470341 NEEDLE BEARING BA66
342 P07470342 BUSHING
EXT RETAINING RING 10MM
399 P07470399 CLUTCH ARM COVER
400 PSS02M
401 PN01M
SET SCREW M6-1 X 6
HEX NUT M6-1
343 P07470343 FEED WORM
403 P07470403 CAM ROD
344 P07470344 FEED WORM SHAFT BUSHING
347 P07470347 FEED WORM SHAFT THRUST WASHER
348 P07470348 BUSHING
404 P07470404 SPRING STUD 1/4-20 X 3-1/4, 3/8
405 P07470324 ROUND PLASTIC KNOB 1/4-20 1" OD
406 P07470406 FEED TRIP BRACKET
407 PCAP02M CAP SCREW M6-1 X 20
349 P07470349 FEED REVERSE BEVEL GEAR
350 P07470350 FEED REVERSE CLUTCH
351 P07470351 FEED REVERSE BEVEL GEAR
352 P07470352 BUSHING
408 PSS02M
409 PK103M
SET SCREW M6-1 X 6
KEY 3 X 3 X 12
410 P07470410 FEED REVERSE KNOB SHOULDER SCREW
411 P07470411 FEED REVERSE KNOB
355 P07470355 REVERSE CLUTCH ROD
356 PRP42M
357 P07470357 FEED WORM SHAFT
359 PRP61M ROLL PIN 3 X 12
360 P07470360 FEED SHAFT ROD
361 PSS26M SET SCREW M5-.8 X 6
ROLL PIN 3 X 20
412 PR02M
413 P07470413 HANDWHEEL CLUTCH
414 PSTB004 STEEL BALL 3/16
415 P07470415 COMPRESSION SPRING
416 PSS20M SET SCREW M8-1.25 X 8
EXT RETAINING RING 14MM
-63-
Model G0747/G0748 (Mfg. Since 8/12)
Downfeed System Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
417
418
419
420
421
423
424
425
427
428
429
430
431
432
433
434
435
436
437
438
440
441
442
444
445
446
448
451
452
453
455
456
457
458
PRP42M
ROLL PIN 3 X 20
459
460
461
462
463
464
465
466
468
469
471
472
475
476
477
478
480
481
482
483
484
485
486
487
488
489
490
491
492
493
493
494
495
P07470459
PR06M
QUILL TRAVEL SCALE
P07470418
PRP61M
CAM ROD SLEEVE ASSEMBLY
ROLL PIN 3 X 12
EXT RETAINING RING 16MM
QUILL TRAVEL STOP LOCK RING
QUILL TRAVEL STOP RING
QUILL TRAVEL DOG
P07470461
P07470462
P07470463
P07470464
P07470465
P07470466
PRP35M
P07470420
P07470421
P07470423
P07470424
P07470425
P07470427
P07470428
P07470429
P07470430
P6206ZZ
COMPRESSION SPRING
TRIP PLUNGER
TRIP PLUNGER BUSHING
FEED TRIP PLUNGER
QUILL TRAVEL SCREW
QUILL TRAVEL DOG SCREW
QUILL PINION SHAFT
FINE DOWNFEED HANDWHEEL ASSY
SPINDLE
ROLL PIN 5 X 10
QUILL SKIRT
PS40M
PHLP HD SCR M5-.8 X 16
KEY 3 X 3 X 20
SPINDLE SPANNER NUT
SPANNER NUT LOCK WASHER
BALL BEARING 6206ZZ
SPINDLE SLEEVE
PK96M
P07470472
P07470475
P07470476
P07470477
P07470478
P07470480
PSS02M
PINION SHAFT HUB SCREW
RACK FEED HANDLE HUB
PINION SHAFT HUB SLEEVE
SPRING COVER
P07470432
P07470433
P07470434
P7207
QUILL NOSE PIECE
LOWER SPINDLE SEAL 64 X 35MM
ANGULAR CONTACT BEARING 7207
LARGE BEARING SPACER
SMALL BEARING SPACER
ANGULAR CONTACT BEARING 7207
SET SCREW M6-1 X 8
QUILL RETURN COIL SPRING
QUILL PINION
P07470436
P07470437
P7207
SET SCREW M6-1 X 6
PSS01M
SET SCREW M6-1 X 10
P07470483
P07470484
P07470485
P07470486
PK102M
REVERSE TRIP BALL LEVER
FEED REVERSE TRIP PLUNGER
REVERSE TRIP BALL LEVER SCREW
WORM GEAR
PSS03M
PSS02M
SET SCREW M6-1 X 6
P07470442
PSS49M
QUILL
SET SCREW M4-.7 X 16
FEED TRIP LEVER
KEY 4 X 4 X 18
P07470445
P07470446
P07470448
P07470451
P07470452
P07470453
P07470455
P07470456
P07470457
PS17M
PSS03M
SET SCREW M6-1 X 8
TRIP LEVER PIN
P07470489
P07470490
P07470491
P07470492
P07470493
P07480493
P07470494
P07470495
WORM SHAFT
UNTAPPED QUILL LOCK PLUNGER
UPPER SPINDLE SEAL
QUILL LOCK HANDLE ASSEMBLY
TAPPED QUILL LOCK PLUNGER
HEAD ROTATION CLAMPING T-BOLT
CLAMPING BOLT SPACER
HEAD ROTATION CLAMPING BOLT
PHLP HD SCR M4-.7 X 6
SHOULDER STUD-DE 3/8-16 X 7-1/4, 1/2
ROUND PLASTIC KNOB 3/8-16 1-1/4" OD
QUILL HOUSING
POWER SWITCH YK 220V 3-POS (G0747)
POWER SWITCH YK 220V 8-POS (G0748)
MOTOR CORD 14G 4W 36"
POWER CORD 14G 4W 72"
-64-
Model G0747/G0748 (Mfg. Since 8/12)
G0747 Headstock
586
586-1
586-4
586-5
586-2
586-3
501
503
539
530
531
532
529
529
533
534
504
505
506
507
508
535
509
541
542
510
511
515
512
513
514
543
585
551
550
545
516
517
518
546
519
527
528
559
557
555
549
524
525
560
520
556
558
562
564
565
561
524
567
566
522
563
578
579
580
581
568
569
523
582
571
572
573
574
577
576
583
584
575
-65-
Model G0747/G0748 (Mfg. Since 8/12)
G0747 Headstock Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
501
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
522
523
524
525
527
528
529
530
531
532
533
534
535
539
541
542
543
545
546
549
P07470501
P07470503
P07470504
P6207ZZ
DRAWBAR 7/16-20 X 23-1/2
UPPER BEARING LOCK NUT
BEARING SLEEVE LOCK NUT
BALL BEARING 6207ZZ
SMALL UPPER BEARING SPACER
LARGE UPPER BEARING SPACER
BALL BEARING 6207ZZ
COMPRESSION SPRING
SET SCREW M6-1 X 12
SPINDLE PULLEY BEARING SLEEVE
HEX NUT 5/16-18
550
551
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
P07470550
PS08M
GEAR HOUSING COVER
PHLP HD SCR M5-.8 X 12
OIL CUP
P07470555
PK40M
KEY 8 X 8 X 16
P07470506
P07470507
P6207ZZ
P07470557
P07470558
P6203ZZ
SPLINED GEAR HUB
SPLINED BULL GEAR 81T
BALL BEARING 6203ZZ
BACK GEAR SHAFT
KEY 5 X 5 X 16
P07470509
PSS04M
P07470560
PK08M
P07470511
PN02
P07470562
P6203ZZ
BACK GEAR 26T
BALL BEARING 6203ZZ
DOWEL PIN 8.8 X 58
BACK GEAR SHIFTER FORK
GEAR HOUSING
PTLW02
EXT TOOTH WASHER 5/16
BRAKE RING STEP SCREW
EXTENSION SPRING
P07470564
P07470565
P07470566
P07470567
P07470568
PCAP06M
P6208ZZ
P07470514
P07470515
PS12M
PHLP HD SCR M3-.5 X 6
BRAKE LOCKING BOLT
BRAKE SHOE ASSEMBLY
SPINDLE PULLEY
DOWEL PIN
P07470517
P07470518
P07470519
P07470520
PVA33
ALIGNMENT PIN
CAP SCREW M6-1 X 25
BALL BEARING 6208ZZ
INT RETAINING RING 80MM
SPANNER NUT LOCK WASHER
SPANNER NUT
SPINDLE PULLEY HUB
V-BELT A-33
PR50M
P07470573
P07470574
PN19
P07470523
P07470524
P07470525
PFH30M
TIMING BELT 225L 1"W 60T
TIMING PULLEY FLANGE
TIMING PULLEY
HEX NUT 7/16-14
P07470576
P07470577
P07470578
PRP42M
T-BOLT
FLAT HD SCR M5-.8 X 8
HEX NUT 5/8-18
T-BOLT FLAT WASHER 7/16"
HIGH-LOW SHIFT LEVER
ROLL PIN 3 X 20
PN09
P07470529
P07470530
P07470531
P07470532
PSS31M
ROUND PLASTIC KNOB 5/16-18 1-1/4" OD
SHOULDER STUD 5/16-18 X 4, 1/2,3/4
CAM RING
P07470580
P07470581
P07470324
P07470583
P07470584
P07470585
P07470586
HIGH-LOW SHIFT BUSHING
HIGH-LOW SHIFT CRANK
ROUND PLASTIC KNOB 1/4-20 1" OD
DETENT LOCK PIN
CAM RING PIN
SET SCREW M5-.8 X 8
BRAKE LEVER
P07470534
P07470535
PN02
COMPRESSION SPRING
BELT SAFETY GUARD
MOTOR 3HP 220V 3-PH AEVF 112-4/2
BRAKE LOCK PIN
HEX NUT 5/16-18
P07470541
P07470542
P07470543
P07470545
P07470529
P07470549
SHOULDER STUD-DE 5/16-18 X 2-1/2, 1/2
BELT HOUSING
586-1 P07470586-1 MOTOR FAN COVER
586-2 P07470586-2 MOTOR FAN
MOTOR LOCK NUT
586-3 P07470586-3 MOTOR JUNCTION BOX
SHOULDER STUD-DE 5/16-18 X 3, 5/8
PLATIC ROUND KNOB 5/16-18 1-1/4" OD
MOTOR PULLEY
586-4 P6205ZZ
586-5 P6205ZZ
BALL BEARING 6205ZZ
BALL BEARING 6205ZZ
-66-
Model G0747/G0748 (Mfg. Since 8/12)
G0748 Headstock
501-1
501-5
501
502
501-4
605
606
501-2
604
537
501-3
506
609
607
507
610
508
602
600
504
601
611
613
614
612
599
509
597
598
616
596
594
534
510
615
595
535
578
536
537
538
593
533
577
560
511
579
512
559
530
529
528
531
576
582
580
556
561
527
513
514
575
574
558
562
557
563
526
525
539
540
541
511
564
565
556
566
523
521
520
519
583
556
543
545
555
617
554
573
584
592
585
562
515
516
570
552
572
571
551
550
570
591
517
547
546
518
587
588
548
545
549
590
589
567
568
-67-
Model G0747/G0748 (Mfg. Since 8/12)
G0748 Headstock Parts List
REF PART #
501 P07480501
DESCRIPTION
REF PART #
DESCRIPTION
MOTOR 3HP 220V 3-PH AEVF 112-4
554 P07480554 BRAKE SHAFT SLEEVE
555 P07480555 BRAKE SHAFT
501-1 P07480501-1 MOTOR FAN COVER
501-2 P07480501-2 MOTOR FAN
556 PCAP01M CAP SCREW M6-1 X 16
557 P07480557 PULLEY COVER
501-3 P07480501-3 MOTOR JUNCTION BOX
501-4 P6205ZZ
501-5 P6205ZZ
BALL BEARING 6205ZZ
BALL BEARING 6205ZZ
MOTOR MOUNT CAP SCREW 3/8-16
BALL BEARING 6009ZZ
CAP SCREW M6-1 X 20
SPINDLE TOP COVER
558 P07480558 TIMING BELT PULLEY
559 PN04
HEX NUT 5/8-11
502
504
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
523
525
526
527
528
529
530
531
533
534
535
536
537
538
539
540
541
543
545
546
547
548
549
550
551
552
P07480502
P6009ZZ
560 P07480560 TIMING BELT 225L
561 P07480561 BEARING HOUSING
PCAP02M
P07480507
P07480508
P07480509
P07480510
PCAP31M
P07480512
P07480513
P07480514
P07480515
P07480516
P07480517
P07480518
PCAP68M
PS03M
562 P6203ZZ
563 P07480563 PINION GEAR
564 PK47M KEY 4 X 4 X 15
BALL BEARING 6203ZZ
UPPER HEADSTOCK HOUSING, ALUMINUM
HOUSING SIDE COVER, PLASTIC
MOTOR FIXED PULLEY
CAP SCREW M8-1.25 X 25
VARIABLE SPEED BELT 3828 9001/Q828
MOTOR MOVABLE PULLEY
MOTOR PULLEY SHAFT
COMPRESSION SPRING
SPRING BASE
565 P07480565 TIMING BELT CLUTCH
566 P07480566 PINION SHAFT
567 P07480567 HEADSTOCK BOTTOM COVER
568 P07480568 BULL GEAR SEAT
570 P07480570 BEARING SLEEVE
571 P07480571 SPACER
572 P07480572 BEARING SLEEVE
573 P07480573 THRUST WASHER
574 P07480574 SPINDLE TIMING PULLEY
575 P07480575 CLUTCH
SPRING BASE CAP SCREW
BRAKE BRACKET, ALUMINUM
CAP SCREW M6-1 X 8
576 P07480576 CLUTCH SHAFT SLEEVE RING
577 P07480577 SPLINE SHAFT
578 P07480578 SPACER
PHLP HD SCR M6-1 X 8
BRAKE SHOE 2-PC SET
BALL BEARING 6012ZZ
LOWER SPINDLE PULLEY
UPPER SPINDLE PULLEY
EXT RETAINING RING 45MM
BALL BEARING 6012ZZ
SLIDING SLEEVE, ALUMINUM
DRAWBAR SPACER 22 X 13 X 8
ROLL PIN 3 X 20
P07480521
P6012ZZ
579 PK34M
580 PK70M
KEY 5 X 5 X 20
KEY 8 X 8 X 12
P07480525
P07480526
PR56M
582 P07480582 BEARING HOUSING
583 P07480583 CLUTCH GEAR SHAFT
584 P07480584 SPEED RANGE POSITIONING PLATE
585 PCAP33M CAP SCREW M5-.8 X 12
587 P07480587 PIVOT ARM
P6012ZZ
P07480529
P07480530
PRP42M
588 PRP07M
ROLL PIN 6 X 20
P07480533
P07480534
P07480535
P07480536
PRP76M
SLEEVE
589 P07480589 ROUND PLASTIC KNOB 1/4"-20
590 P07480590 SPRING STUD 1/4"-20 X 3/4"
591 P07480591 COMPRESSION SPRING
592 P07480592 SPEED RANGE POSITIONING PIN
593 P07480593 HANDWHEEL HANDLE
PLATE ADJUSTING ROD
DRAWBAR 7/16"-20 X 23-1/2"
CHAIN PIN
ROLL PIN 4 X 16
P07480538
PR43M
SPEED CHANGE PLATE
EXT RETAINING RING 50MM
PHLP HD SCR 5-40 X 1/4
BRAKE EXTENSION SPRING
HEX BOLT M8-1.25 X 20
E-CLIP 13MM
594 P07480594 SPEED HANDWHEEL INFO PLATE
595 P07480595 HANDWHEEL
PS50
596 PSS02M
SET SCREW M6-1 X 6
P07480541
PB09M
597 P07480597 BRASS SLEEVE
598 P07480598 SPEED CHANGE SHAFT
PEC04M
599 PRP61M
ROLL PIN 3 X 12
P07480546
P07480547
PCAP85M
P07480549
P07480550
PN08
BRAKE PIVOT ARM 2-PC SET
BRAKE PIVOT ROD
600 P07480600 WORM
601 PRP115M ROLL PIN 5 X 8
602 P07480602 CHAIN SHAFT
604 P07480604 CHAIN
CAP SCREW M6-1 X 6
TAPERED KNOB 3/8-16
BRAKE LEVER
605 P07480605 CHAIN MASTER LINK
606 P07480606 MASTER LINK PIN
607 P07480607 WORM GEAR
HEX NUT 3/8-16
PCAP06M
CAP SCREW M6-1 X 25
-68-
Model G0747/G0748 (Mfg. Since 8/12)
G0748 Headstock Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
609 P07480609 HEADSTOCK FRONT COVER, ALUMINUM
610 PCAP07M CAP SCREW M6-1 X 30
611 PCAP01M CAP SCREW M6-1 X 16
612 P07480612 BRASS SLEEVE
614 P07480614 SPEED CHANGE INDICATOR PLATE
615 PCAP26M CAP SCREW M6-1 X 12
616 PN40
ACORN NUT 5/16-18
617 P07480617 BRAKE PIVOT ARM
613 P07480613 SPEED CHANGE DIAL
-69-
Model G0747/G0748 (Mfg. Since 8/12)
One-Shot Oiler
709
703
706
703
709
702
706
705
704
702
706
704
707
701
704
702
708
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
701
702
703
704
705
P07470701
P07470702
P07470703
PCAP02M
P07470705
OILER PUMP AND RESERVOIR
ALUMINUM PIPE 4MM
706
707
708
709
P07470706
P07470707
P07470708
P07470709
ELBOW OIL DISTRIBUTOR CPS3
FLEXIBLE STEEL TUBE
ELBOW OIL DISTRIBUTOR CPS4
CAP SCREW M6-1 X 20
A-TYPE OIL DISTRIBUTOR A8
ELBOW OIL DISTRIBUTOR CPS5
A-TYPE OIL DISTRIBUTOR A4
-70-
Model G0747/G0748 (Mfg. Since 8/12)
Accessories
805
802
803
801
804
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
801
802
803
P07470801
PWR1719C
PSDF2
BOTTLE FOR OIL
804
805
PSDP2
PHILLIPS SCREWDRIVER #2
TOOLBOX
WRENCH 17 X 19MM CLOSED ENDS
STANDARD SCREWDRIVER #2
P07470805
-71-
Model G0747/G0748 (Mfg. Since 8/12)
G0747 Machine Labels & Cosmetics
902
901
903
904
913
912
911
910
906
905
909
908
904
907
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
901
902
903
904
905
906
907
P07470901
P07470902
G8588
MODEL NUMBER LABEL
908
909
910
911
912
913
PLABEL-52C
220V DISCONNECT LABEL
ENTANGLEMENT LABEL
READ MANUAL LABEL
QUILL FEED LABEL
220V 3-PHASE ELECTRICITY LABEL
SMALL GRIZZLY NAMEPLATE
ELECTRICITY LABEL
PLABEL-55C
PLABEL-12D
P07470911
P07470912
P07470913
PLABEL-14A
P07470905
PPAINT-1
P07470907
MACHINE ID LABEL
SPEED RANGE LABEL
SPINDLE SPEED LABEL
GRIZZLY GREEN TOUCH-UP PAINT
GOGGLES/FACE SHIELD LABEL
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
-72-
Model G0747/G0748 (Mfg. Since 8/12)
G0748 Machine Labels & Cosmetics
901
903
904
912
911
910
909
908
906
905
907
904
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
901
903
904
905
906
907
P07480901
H4609
MODEL NUMBER LABEL
908
909
910
911
912
PLABEL-52C
220V DISCONNECT LABEL
ENTANGLEMENT LABEL
READ MANUAL LABEL
QUILL FEED LABEL
SMALL OBLONG GRIZZLY NAMEPLATE
ELECTRICITY LABEL
PLABEL-55C
PLABEL-12D
P07470911
P07470912
PLABEL-14A
P07480905
PPAINT-1
P07471007
MACHINE ID LABEL
GRIZZLY GREEN TOUCH-UP PAINT
GOGGLES/FACE SHIELD LABEL
SPEED RANGE LABEL
-73-
Model G0747/G0748 (Mfg. Since 8/12)
-74-
Model G0747/G0748 (Mfg. Since 8/12)
WARRANTY CARD
Name_____________________________________________________________________________
Street_____________________________________________________________________________
City _______________________ State_________________________ Zip _____________________
Phone #____________________ Email _________________________________________________
Model # ____________________ Order #_______________________ Serial #__________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement
____ Card Deck
____ Friend
____ Website
____ Catalog
____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinetmaker & FDM
____ Family Handyman
____ Hand Loader
____ Popular Science
____ Popular Woodworking
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rifle
____ Shop Notes
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Woodwork
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Model Airplane News
____ Old House Journal
____ Popular Mechanics
____ Shotgun News
____ Today’s Homeowner
____ Wood
3. What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $40,000-$49,000
____ $70,000+
____ $50,000-$59,000
____ $60,000-$69,000
4. What is your age group?
____ 20-29
____ 30-39
____ 60-69
____ 40-49
____ 70+
____ 50-59
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years
____ 8-20 Years
____20+ Years
____10+
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5
____ 6-9
7. Do you think your machine represents a good value?
_____Yes
_____Yes
_____No
_____No
8. Would you recommend Grizzly Industrial to a friend?
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments:_____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
WARRANTy & RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue
you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We
will not accept any item back without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
|